/* ATR - Arbiter Timers Register
*/
#define ATR_DTO 0x00FF0000 /* Data time out */
+#define ATR_DTO_SHIFT 16
#define ATR_ATO 0x000000FF /* Address time out */
+#define ATR_ATO_SHIFT 0
/* AER - Arbiter Event Register
*/
/* AEATR - Arbiter Event Address Register
*/
#define AEATR_EVENT 0x07000000 /* Event type */
+#define AEATR_EVENT_SHIFT 24
#define AEATR_MSTR_ID 0x001F0000 /* Master Id */
+#define AEATR_MSTR_ID_SHIFT 16
#define AEATR_TBST 0x00000800 /* Transfer burst */
+#define AEATR_TBST_SHIFT 11
#define AEATR_TSIZE 0x00000700 /* Transfer Size */
+#define AEATR_TSIZE_SHIFT 8
#define AEATR_TTYPE 0x0000001F /* Transfer Type */
+#define AEATR_TTYPE_SHIFT 0
/* HRCWL - Hard Reset Configuration Word Low
*/
#if defined(CONFIG_MPC834X)
#define HRCWH_ROM_LOC_PCI2 0x00200000
#endif
-#if defined(CONIFG_MPC837X)
+#if defined(CONFIG_MPC837X)
#define HRCWH_ROM_LOC_ON_CHIP_ROM 0x00300000
#endif
#define HRCWH_ROM_LOC_LOCAL_8BIT 0x00500000
#define HRCWH_RL_EXT_LEGACY 0x00000000
#define HRCWH_RL_EXT_NAND 0x00040000
+#define HRCWH_TSEC1M_MASK 0x0000E000
#define HRCWH_TSEC1M_IN_MII 0x00000000
#define HRCWH_TSEC1M_IN_RMII 0x00002000
#define HRCWH_TSEC1M_IN_RGMII 0x00006000
#define HRCWH_TSEC1M_IN_RTBI 0x0000A000
#define HRCWH_TSEC1M_IN_SGMII 0x0000C000
+#define HRCWH_TSEC2M_MASK 0x00001C00
#define HRCWH_TSEC2M_IN_MII 0x00000000
#define HRCWH_TSEC2M_IN_RMII 0x00000400
#define HRCWH_TSEC2M_IN_RGMII 0x00000C00
#define SCCR_USBDRCM_2 0x00800000
#define SCCR_USBDRCM_3 0x00c00000
-#define SCCR_PCIEXP1CM 0x00300000
-#define SCCR_PCIEXP2CM 0x000c0000
-
#define SCCR_SATA1CM 0x00003000
#define SCCR_SATA1CM_SHIFT 12
#define SCCR_SATACM 0x00003c00
#define SCCR_USBDRCM_2 0x00800000
#define SCCR_USBDRCM_3 0x00c00000
+/* All of the four SATA controllers must have the same clock ratio */
+#define SCCR_SATA1CM 0x000000c0
+#define SCCR_SATA1CM_SHIFT 6
+#define SCCR_SATACM 0x000000ff
+#define SCCR_SATACM_SHIFT 0
+#define SCCR_SATACM_0 0x00000000
+#define SCCR_SATACM_1 0x00000055
+#define SCCR_SATACM_2 0x000000aa
+#define SCCR_SATACM_3 0x000000ff
+#endif
+
#define SCCR_PCIEXP1CM 0x00300000
#define SCCR_PCIEXP1CM_SHIFT 20
#define SCCR_PCIEXP1CM_0 0x00000000
#define SCCR_PCIEXP2CM_2 0x00080000
#define SCCR_PCIEXP2CM_3 0x000c0000
-/* All of the four SATA controllers must have the same clock ratio */
-#define SCCR_SATA1CM 0x000000c0
-#define SCCR_SATA1CM_SHIFT 6
-#define SCCR_SATACM 0x000000ff
-#define SCCR_SATACM_SHIFT 0
-#define SCCR_SATACM_0 0x00000000
-#define SCCR_SATACM_1 0x00000055
-#define SCCR_SATACM_2 0x000000aa
-#define SCCR_SATACM_3 0x000000ff
-#endif
-
/* CSn_BDNS - Chip Select memory Bounds Register
*/
#define CSBNDS_SA 0x00FF0000
#define TIMING_CFG1_WRTORD_SHIFT 0
#define TIMING_CFG1_CASLAT_20 0x00030000 /* CAS latency = 2.0 */
#define TIMING_CFG1_CASLAT_25 0x00040000 /* CAS latency = 2.5 */
-#define TIMING_CFG1_CASLAT_30 0x00050000 /* CAS latency = 2.5 */
+#define TIMING_CFG1_CASLAT_30 0x00050000 /* CAS latency = 3.0 */
+#define TIMING_CFG1_CASLAT_35 0x00060000 /* CAS latency = 3.5 */
+#define TIMING_CFG1_CASLAT_40 0x00070000 /* CAS latency = 4.0 */
/* TIMING_CFG_2 - DDR SDRAM Timing Configuration 2
*/
*/
#define PMCCR1_POWER_OFF 0x00000020
-/* FMR - Flash Mode Register
- */
-#define FMR_CWTO 0x0000F000
-#define FMR_CWTO_SHIFT 12
-#define FMR_BOOT 0x00000800
-#define FMR_ECCM 0x00000100
-#define FMR_AL 0x00000030
-#define FMR_AL_SHIFT 4
-#define FMR_OP 0x00000003
-#define FMR_OP_SHIFT 0
-
-/* FIR - Flash Instruction Register
- */
-#define FIR_OP0 0xF0000000
-#define FIR_OP0_SHIFT 28
-#define FIR_OP1 0x0F000000
-#define FIR_OP1_SHIFT 24
-#define FIR_OP2 0x00F00000
-#define FIR_OP2_SHIFT 20
-#define FIR_OP3 0x000F0000
-#define FIR_OP3_SHIFT 16
-#define FIR_OP4 0x0000F000
-#define FIR_OP4_SHIFT 12
-#define FIR_OP5 0x00000F00
-#define FIR_OP5_SHIFT 8
-#define FIR_OP6 0x000000F0
-#define FIR_OP6_SHIFT 4
-#define FIR_OP7 0x0000000F
-#define FIR_OP7_SHIFT 0
-#define FIR_OP_NOP 0x0 /* No operation and end of sequence */
-#define FIR_OP_CA 0x1 /* Issue current column address */
-#define FIR_OP_PA 0x2 /* Issue current block+page address */
-#define FIR_OP_UA 0x3 /* Issue user defined address */
-#define FIR_OP_CM0 0x4 /* Issue command from FCR[CMD0] */
-#define FIR_OP_CM1 0x5 /* Issue command from FCR[CMD1] */
-#define FIR_OP_CM2 0x6 /* Issue command from FCR[CMD2] */
-#define FIR_OP_CM3 0x7 /* Issue command from FCR[CMD3] */
-#define FIR_OP_WB 0x8 /* Write FBCR bytes from FCM buffer */
-#define FIR_OP_WS 0x9 /* Write 1 or 2 bytes from MDR[AS] */
-#define FIR_OP_RB 0xA /* Read FBCR bytes to FCM buffer */
-#define FIR_OP_RS 0xB /* Read 1 or 2 bytes to MDR[AS] */
-#define FIR_OP_CW0 0xC /* Wait then issue FCR[CMD0] */
-#define FIR_OP_CW1 0xD /* Wait then issue FCR[CMD1] */
-#define FIR_OP_RBW 0xE /* Wait then read FBCR bytes */
-#define FIR_OP_RSW 0xF /* Wait then read 1 or 2 bytes */
-
-/* FCR - Flash Command Register
- */
-#define FCR_CMD0 0xFF000000
-#define FCR_CMD0_SHIFT 24
-#define FCR_CMD1 0x00FF0000
-#define FCR_CMD1_SHIFT 16
-#define FCR_CMD2 0x0000FF00
-#define FCR_CMD2_SHIFT 8
-#define FCR_CMD3 0x000000FF
-#define FCR_CMD3_SHIFT 0
-
-/* FBAR - Flash Block Address Register
- */
-#define FBAR_BLK 0x00FFFFFF
-
-/* FPAR - Flash Page Address Register
- */
-#define FPAR_SP_PI 0x00007C00
-#define FPAR_SP_PI_SHIFT 10
-#define FPAR_SP_MS 0x00000200
-#define FPAR_SP_CI 0x000001FF
-#define FPAR_SP_CI_SHIFT 0
-#define FPAR_LP_PI 0x0003F000
-#define FPAR_LP_PI_SHIFT 12
-#define FPAR_LP_MS 0x00000800
-#define FPAR_LP_CI 0x000007FF
-#define FPAR_LP_CI_SHIFT 0
-
-/* LTESR - Transfer Error Status Register
- */
-#define LTESR_BM 0x80000000
-#define LTESR_FCT 0x40000000
-#define LTESR_PAR 0x20000000
-#define LTESR_WP 0x04000000
-#define LTESR_ATMW 0x00800000
-#define LTESR_ATMR 0x00400000
-#define LTESR_CS 0x00080000
-#define LTESR_CC 0x00000001
-
/* DDRCDR - DDR Control Driver Register
*/
#define DDRCDR_DHC_EN 0x80000000
#define DDRCDR_M_ODR 0x00000002
#define DDRCDR_Q_DRN 0x00000001
+/* PCIE Bridge Register
+*/
+#define PEX_CSB_CTRL_OBPIOE 0x00000001
+#define PEX_CSB_CTRL_IBPIOE 0x00000002
+#define PEX_CSB_CTRL_WDMAE 0x00000004
+#define PEX_CSB_CTRL_RDMAE 0x00000008
+
+#define PEX_CSB_OBCTRL_PIOE 0x00000001
+#define PEX_CSB_OBCTRL_MEMWE 0x00000002
+#define PEX_CSB_OBCTRL_IOWE 0x00000004
+#define PEX_CSB_OBCTRL_CFGWE 0x00000008
+
+#define PEX_CSB_IBCTRL_PIOE 0x00000001
+
+#define PEX_OWAR_EN 0x00000001
+#define PEX_OWAR_TYPE_CFG 0x00000000
+#define PEX_OWAR_TYPE_IO 0x00000002
+#define PEX_OWAR_TYPE_MEM 0x00000004
+#define PEX_OWAR_RLXO 0x00000008
+#define PEX_OWAR_NANP 0x00000010
+#define PEX_OWAR_SIZE 0xFFFFF000
+
+#define PEX_IWAR_EN 0x00000001
+#define PEX_IWAR_TYPE_INT 0x00000000
+#define PEX_IWAR_TYPE_PF 0x00000004
+#define PEX_IWAR_TYPE_NO_PF 0x00000006
+#define PEX_IWAR_NSOV 0x00000008
+#define PEX_IWAR_NSNP 0x00000010
+#define PEX_IWAR_SIZE 0xFFFFF000
+#define PEX_IWAR_SIZE_1M 0x000FF000
+#define PEX_IWAR_SIZE_2M 0x001FF000
+#define PEX_IWAR_SIZE_4M 0x003FF000
+#define PEX_IWAR_SIZE_8M 0x007FF000
+#define PEX_IWAR_SIZE_16M 0x00FFF000
+#define PEX_IWAR_SIZE_32M 0x01FFF000
+#define PEX_IWAR_SIZE_64M 0x03FFF000
+#define PEX_IWAR_SIZE_128M 0x07FFF000
+#define PEX_IWAR_SIZE_256M 0x0FFFF000
+
+#define PEX_GCLK_RATIO 0x440
+
#ifndef __ASSEMBLY__
struct pci_region;
void mpc83xx_pci_init(int num_buses, struct pci_region **reg, int warmboot);
+void mpc83xx_pcislave_unlock(int bus);
+void mpc83xx_pcie_init(int num_buses, struct pci_region **reg, int warmboot);
#endif
#endif /* __MPC83XX_H__ */
projects / karo-tx-uboot.git / blobdiff