X-Git-Url: https://git.kernelconcepts.de/?a=blobdiff_plain;f=include%2Fconfigs%2FHUB405.h;h=afb827324af96857a41d032a767510a63687ed9a;hb=88a85fb9f3578f513d7053ac9a3f1ff7521b2771;hp=0e7d2c010399348cdc0771d245ce6638c1836534;hpb=ee924e00300bd1136589b2d5f8ad1f008df01bd4;p=karo-tx-uboot.git

diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index 0e7d2c0103..afb827324a 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -37,6 +37,8 @@
 #define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_HUB405		1	/* ...on a HUB405 board		*/
 
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
@@ -117,9 +119,14 @@
 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
 #undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
 #define CONFIG_SYS_BASE_BAUD	    691200
-#undef	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE	\
@@ -243,6 +250,7 @@
  * I2C EEPROM (CAT24WC16) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
@@ -314,10 +322,9 @@
 #define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
 #define CONFIG_SYS_OCM_DATA_SIZE	0x1000
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
 
-#define CONFIG_SYS_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -332,12 +339,12 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CONFIG_SYS_GPIO0_OSRH		0x40000550
-#define CONFIG_SYS_GPIO0_OSRL		0x00000110
-#define CONFIG_SYS_GPIO0_ISR1H		0x00000000
-#define CONFIG_SYS_GPIO0_ISR1L		0x15555445
-#define CONFIG_SYS_GPIO0_TSRH		0x00000000
+#define CONFIG_SYS_GPIO0_OSRL		0x40000550
+#define CONFIG_SYS_GPIO0_OSRH		0x00000110
+#define CONFIG_SYS_GPIO0_ISR1L		0x00000000
+#define CONFIG_SYS_GPIO0_ISR1H		0x15555445
 #define CONFIG_SYS_GPIO0_TSRL		0x00000000
+#define CONFIG_SYS_GPIO0_TSRH		0x00000000
 #define CONFIG_SYS_GPIO0_TCR		0xF7FE0014
 
 #define CONFIG_SYS_DUART_RST           (0x80000000 >> 14)
@@ -346,14 +353,6 @@
 #define CONFIG_SYS_UART4_RS232         (0x80000000 >> 7)
 #define CONFIG_SYS_UART5_RS232         (0x80000000 >> 8)
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
 /*
  * Default speed selection (cpu_plb_opb_ebc) in mhz.
  * This value will be set if iic boot eprom is disabled.