--- /dev/null
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+ "arm,pl310-cache"
+ "arm,l220-cache"
+ "arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+ registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+ read, write and setup latencies. Minimum valid values are 1. Controllers
+ without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+ read, write and setup latencies. Controllers without setup latency control
+ should use 0. Controllers without separate read and write Tag RAM latency
+ values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+ filter. Addresses in the filter window are directed to the M1 port. Other
+ addresses will go to the M0 port.
+
+Example:
+
+L2: cache-controller {
+ compatible = "arm,pl310-cache";
+ reg = <0xfff12000 0x1000>;
+ arm,data-latency = <1 1 1>;
+ arm,tag-latency = <2 2 2>;
+ arm,filter-latency = <0x80000000 0x8000000>;
+ cache-unified;
+ cache-level = <2>;
+};
The base address of exception vectors.
config ARM_PATCH_PHYS_VIRT
- bool "Patch physical to virtual translations at runtime"
+ bool "Patch physical to virtual translations at runtime" if EMBEDDED
+ default y
depends on !XIP_KERNEL && MMU
depends on !ARCH_REALVIEW || !SPARSEMEM
help
kernel in system memory.
This can only be used with non-XIP MMU kernels where the base
- of physical memory is at a 16MB boundary, or theoretically 64K
- for the MSM machine class.
+ of physical memory is at a 16MB boundary.
+
+ Only disable this option if you know that you do not require
+ this feature (eg, building a kernel for a single machine) and
+ you need to shrink the kernel to the minimal size.
-config ARM_PATCH_PHYS_VIRT_16BIT
- def_bool y
- depends on ARM_PATCH_PHYS_VIRT && ARCH_MSM
- help
- This option extends the physical to virtual translation patching
- to allow physical memory down to a theoretical minimum of 64K
- boundaries.
source "init/Kconfig"
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
select CLKDEV_LOOKUP
- select ARM_PATCH_PHYS_VIRT if MMU
help
This enables support for systems based on the Atmel AT91RM9200,
AT91SAM9 and AT91CAP9 processors.
If you don't know what to do here, say Y.
+config ARM_CPU_TOPOLOGY
+ bool "Support cpu topology definition"
+ depends on SMP && CPU_V7
+ default y
+ help
+ Support ARM cpu topology definition. The MPIDR register defines
+ affinity between processors which is then used to describe the cpu
+ topology of an ARM System.
+
+config SCHED_MC
+ bool "Multi-core scheduler support"
+ depends on ARM_CPU_TOPOLOGY
+ help
+ Multi-core scheduler support improves the CPU scheduler's decision
+ making when dealing with multi-core CPU chips at a cost of slightly
+ increased overhead in some places. If unsure say N here.
+
+config SCHED_SMT
+ bool "SMT scheduler support"
+ depends on ARM_CPU_TOPOLOGY
+ help
+ Improves the CPU scheduler's decision making when dealing with
+ MultiThreading at a cost of slightly increased overhead in some
+ places. If unsure say N here.
+
config HAVE_ARM_SCU
bool
help
ifeq ($(CONFIG_ARCH_SA1100),y)
textofs-$(CONFIG_SA1111) := 0x00208000
endif
+textofs-$(CONFIG_ARCH_MSM7X30) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
# Machine directory name. This list is sorted alphanumerically
# by CONFIG_* macro name.
$(obj)/uImage: STARTADDR=$(LOADADDR)
+check_for_multiple_loadaddr = \
+if [ $(words $(LOADADDR)) -gt 1 ]; then \
+ echo 'multiple load addresses: $(LOADADDR)'; \
+ echo 'This is incompatible with uImages'; \
+ echo 'Specify LOADADDR on the commandline to build an uImage'; \
+ false; \
+fi
+
$(obj)/uImage: $(obj)/zImage FORCE
+ @$(check_for_multiple_loadaddr)
$(call if_changed,uimage)
@echo ' Image $@ is ready'
( echo "following symbols must have non local/private scope:" >&2; \
echo "$$bad_syms" >&2; rm -f $@; false )
+check_for_multiple_zreladdr = \
+if [ $(words $(ZRELADDR)) -gt 1 -a "$(CONFIG_AUTO_ZRELADDR)" == "" ]; then \
+ echo 'multiple zreladdrs: $(ZRELADDR)'; \
+ echo 'This needs CONFIG_AUTO_ZRELADDR to be set'; \
+ false; \
+fi
+
$(obj)/vmlinux: $(obj)/vmlinux.lds $(obj)/$(HEAD) $(obj)/piggy.$(suffix_y).o \
$(addprefix $(obj)/, $(OBJS)) $(lib1funcs) FORCE
+ @$(check_for_multiple_zreladdr)
$(call if_changed,ld)
@$(check_for_bad_syms)
return -EINVAL;
mask = 0xff << shift;
- bit = 1 << (cpu + shift);
+ bit = 1 << (cpu_logical_map(cpu) + shift);
spin_lock(&irq_controller_lock);
val = readl_relaxed(reg) & ~mask;
unsigned int irq_start)
{
unsigned int gic_irqs, irq_limit, i;
+ u32 cpumask;
void __iomem *base = gic->dist_base;
- u32 cpumask = 1 << smp_processor_id();
+ u32 cpu = 0;
+#ifdef CONFIG_SMP
+ cpu = cpu_logical_map(smp_processor_id());
+#endif
+
+ cpumask = 1 << cpu;
cpumask |= cpumask << 8;
cpumask |= cpumask << 16;
#ifdef CONFIG_SMP
void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
{
- unsigned long map = *cpus_addr(*mask);
+ int cpu;
+ unsigned long map = 0;
+
+ /* Convert our logical CPU mask into a physical one. */
+ for_each_cpu(cpu, mask)
+ map |= 1 << cpu_logical_map(cpu);
/*
* Ensure that stores to Normal memory are visible to the
*/
#include <linux/device.h>
+#include <linux/gpio.h>
#include <linux/string.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <asm/gpio.h>
#include <asm/hardware/scoop.h>
/* PCMCIA to Scoop linkage
include include/asm-generic/Kbuild.asm
header-y += hwcap.h
+
+generic-y += auxvec.h
+generic-y += bitsperlong.h
+generic-y += cputime.h
+generic-y += emergency-restart.h
+generic-y += errno.h
+generic-y += ioctl.h
+generic-y += irq_regs.h
+generic-y += kdebug.h
+generic-y += local.h
+generic-y += local64.h
+generic-y += percpu.h
+generic-y += poll.h
+generic-y += resource.h
+generic-y += sections.h
+generic-y += siginfo.h
+generic-y += sizes.h
+++ /dev/null
-#ifndef __ASMARM_AUXVEC_H
-#define __ASMARM_AUXVEC_H
-
-#endif
+++ /dev/null
-#include <asm-generic/bitsperlong.h>
+++ /dev/null
-#ifndef __ARM_CPUTIME_H
-#define __ARM_CPUTIME_H
-
-#include <asm-generic/cputime.h>
-
-#endif /* __ARM_CPUTIME_H */
#define CPUID_CACHETYPE 1
#define CPUID_TCM 2
#define CPUID_TLBTYPE 3
+#define CPUID_MPIDR 5
#define CPUID_EXT_PFR0 "c1, 0"
#define CPUID_EXT_PFR1 "c1, 1"
return read_cpuid(CPUID_TCM);
}
+static inline unsigned int __attribute_const__ read_cpuid_mpidr(void)
+{
+ return read_cpuid(CPUID_MPIDR);
+}
+
/*
* Intel's XScale3 core supports some v6 features (supersections, L2)
* but advertises itself as v5 as it does not support the v6 ISA. For
static inline void *dma_to_virt(struct device *dev, dma_addr_t addr)
{
- return (void *)__bus_to_virt(addr);
+ return (void *)__bus_to_virt((unsigned long)addr);
}
static inline dma_addr_t virt_to_dma(struct device *dev, void *addr)
int dma_mmap_writecombine(struct device *, struct vm_area_struct *,
void *, dma_addr_t, size_t);
+/*
+ * This can be called during boot to increase the size of the consistent
+ * DMA region above it's default value of 2MB. It must be called before the
+ * memory allocator is initialised, i.e. before any core_initcall.
+ */
+extern void __init init_consistent_dma_size(unsigned long size);
+
#ifdef CONFIG_DMABOUNCE
/*
/* Private internal data */
const char *card_desc; /* Card description */
- CONST unsigned int podaddr; /* Base Linux address for card */
CONST loader_t loader; /* loader program */
u64 dma_mask;
};
+++ /dev/null
-#ifndef _ASM_EMERGENCY_RESTART_H
-#define _ASM_EMERGENCY_RESTART_H
-
-#include <asm-generic/emergency-restart.h>
-
-#endif /* _ASM_EMERGENCY_RESTART_H */
+++ /dev/null
-#ifndef _ARM_ERRNO_H
-#define _ARM_ERRNO_H
-
-#include <asm-generic/errno.h>
-
-#endif
/* not all ARM platforms necessarily support this API ... */
#include <mach/gpio.h>
+#ifndef __ARM_GPIOLIB_COMPLEX
+/* Note: this may rely upon the value of ARCH_NR_GPIOS set in mach/gpio.h */
+#include <asm-generic/gpio.h>
+
+/* The trivial gpiolib dispatchers */
+#define gpio_get_value __gpio_get_value
+#define gpio_set_value __gpio_set_value
+#define gpio_cansleep __gpio_cansleep
+#endif
+
+/*
+ * Provide a default gpio_to_irq() which should satisfy every case.
+ * However, some platforms want to do this differently, so allow them
+ * to override it.
+ */
+#ifndef gpio_to_irq
+#define gpio_to_irq __gpio_to_irq
+#endif
+
#endif /* _ARCH_ARM_GPIO_H */
#define L2X0_CLEAN_INV_WAY 0x7FC
#define L2X0_LOCKDOWN_WAY_D 0x900
#define L2X0_LOCKDOWN_WAY_I 0x904
+#define L2X0_ADDR_FILTER_START 0xC00
+#define L2X0_ADDR_FILTER_END 0xC04
#define L2X0_TEST_OPERATION 0xF00
#define L2X0_LINE_DATA 0xF10
#define L2X0_LINE_TAG 0xF30
#define L2X0_CACHE_ID_PART_L310 (3 << 6)
#define L2X0_AUX_CTRL_MASK 0xc0000fff
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT 0
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK 0x7
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT 3
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK (0x7 << 3)
+#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT 6
+#define L2X0_AUX_CTRL_TAG_LATENCY_MASK (0x7 << 6)
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT 9
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK (0x7 << 9)
#define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT 16
#define L2X0_AUX_CTRL_WAY_SIZE_SHIFT 17
#define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x7 << 17)
#define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT 29
#define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT 30
+#define L2X0_LATENCY_CTRL_SETUP_SHIFT 0
+#define L2X0_LATENCY_CTRL_RD_SHIFT 4
+#define L2X0_LATENCY_CTRL_WR_SHIFT 8
+
+#define L2X0_ADDR_FILTER_EN 1
+
#ifndef __ASSEMBLY__
extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
+extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
#endif
#endif
#include <mach/hardware.h>
#include <asm-generic/gpio.h>
+#define __ARM_GPIOLIB_COMPLEX
+
#define IOP3XX_N_GPIOS 8
static inline int gpio_get_value(unsigned gpio)
*/
#include <mach/io.h>
+/*
+ * This is the limit of PC card/PCI/ISA IO space, which is by default
+ * 64K if we have PC card, PCI or ISA support. Otherwise, default to
+ * zero to prevent ISA/PCI drivers claiming IO space (and potentially
+ * oopsing.)
+ *
+ * Only set this larger if you really need inb() et.al. to operate over
+ * a larger address space. Note that SOC_COMMON ioremaps each sockets
+ * IO space area, and so inb() et.al. must be defined to operate as per
+ * readb() et.al. on such platforms.
+ */
+#ifndef IO_SPACE_LIMIT
+#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff)
+#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffff)
+#else
+#define IO_SPACE_LIMIT ((resource_size_t)0)
+#endif
+#endif
+
/*
* IO port access primitives
* -------------------------
+++ /dev/null
-#include <asm-generic/ioctl.h>
+++ /dev/null
-#include <asm-generic/irq_regs.h>
+++ /dev/null
-#include <asm-generic/kdebug.h>
+++ /dev/null
-#include <asm-generic/local.h>
+++ /dev/null
-#include <asm-generic/local64.h>
struct machine_desc {
unsigned int nr; /* architecture number */
const char *name; /* architecture name */
- unsigned long boot_params; /* tagged list */
+ unsigned long atag_offset; /* tagged list (relative) */
const char **dt_compat; /* array of device tree
* 'compatible' strings */
*/
#define IOREMAP_MAX_ORDER 24
-/*
- * Size of DMA-consistent memory region. Must be multiple of 2M,
- * between 2MB and 14MB inclusive.
- */
-#ifndef CONSISTENT_DMA_SIZE
-#define CONSISTENT_DMA_SIZE SZ_2M
-#endif
-
#define CONSISTENT_END (0xffe00000UL)
-#define CONSISTENT_BASE (CONSISTENT_END - CONSISTENT_DMA_SIZE)
#else /* CONFIG_MMU */
* so that all we need to do is modify the 8-bit constant field.
*/
#define __PV_BITS_31_24 0x81000000
-#define __PV_BITS_23_16 0x00810000
extern unsigned long __pv_phys_offset;
#define PHYS_OFFSET __pv_phys_offset
{
unsigned long t;
__pv_stub(x, t, "add", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- __pv_stub(t, t, "add", __PV_BITS_23_16);
-#endif
return t;
}
{
unsigned long t;
__pv_stub(x, t, "sub", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- __pv_stub(t, t, "sub", __PV_BITS_23_16);
-#endif
return t;
}
#else
/* Add __virt_to_phys patching state as well */
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-#define MODULE_ARCH_VERMAGIC_P2V "p2v16 "
-#else
#define MODULE_ARCH_VERMAGIC_P2V "p2v8 "
-#endif
#else
#define MODULE_ARCH_VERMAGIC_P2V ""
#endif
+++ /dev/null
-#ifndef __ARM_PERCPU
-#define __ARM_PERCPU
-
-#include <asm-generic/percpu.h>
-
-#endif
*/
#define pmd_alloc_one(mm,addr) ({ BUG(); ((pmd_t *)2); })
#define pmd_free(mm, pmd) do { } while (0)
-#define pgd_populate(mm,pmd,pte) BUG()
+#define pud_populate(mm,pmd,pte) BUG()
extern pgd_t *pgd_alloc(struct mm_struct *mm);
extern void pgd_free(struct mm_struct *mm, pgd_t *pgd);
#define _ASMARM_PGTABLE_H
#include <linux/const.h>
-#include <asm-generic/4level-fixup.h>
#include <asm/proc-fns.h>
#ifndef CONFIG_MMU
+#include <asm-generic/4level-fixup.h>
#include "pgtable-nommu.h"
#else
+#include <asm-generic/pgtable-nopud.h>
#include <asm/memory.h>
#include <mach/vmalloc.h>
#include <asm/pgtable-hwdef.h>
#define pgd_offset_k(addr) pgd_offset(&init_mm, addr)
/*
- * The "pgd_xxx()" functions here are trivial for a folded two-level
- * setup: the pgd is never bad, and a pmd always exists (as it's folded
- * into the pgd entry)
+ * The "pud_xxx()" functions here are trivial when the pmd is folded into
+ * the pud: the pud entry is never bad, always exists, and can't be set or
+ * cleared.
*/
-#define pgd_none(pgd) (0)
-#define pgd_bad(pgd) (0)
-#define pgd_present(pgd) (1)
-#define pgd_clear(pgdp) do { } while (0)
-#define set_pgd(pgd,pgdp) do { } while (0)
+#define pud_none(pud) (0)
+#define pud_bad(pud) (0)
+#define pud_present(pud) (1)
+#define pud_clear(pudp) do { } while (0)
#define set_pud(pud,pudp) do { } while (0)
/* Find an entry in the second-level page table.. */
-#define pmd_offset(dir, addr) ((pmd_t *)(dir))
+static inline pmd_t *pmd_offset(pud_t *pud, unsigned long addr)
+{
+ return (pmd_t *)pud;
+}
#define pmd_none(pmd) (!pmd_val(pmd))
#define pmd_present(pmd) (pmd_val(pmd))
+++ /dev/null
-#include <asm-generic/poll.h>
+++ /dev/null
-#ifndef _ARM_RESOURCE_H
-#define _ARM_RESOURCE_H
-
-#include <asm-generic/resource.h>
-
-#endif
+++ /dev/null
-#include <asm-generic/sections.h>
+++ /dev/null
-#ifndef _ASMARM_SIGINFO_H
-#define _ASMARM_SIGINFO_H
-
-#include <asm-generic/siginfo.h>
-
-#endif
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-/* Size definitions
- * Copyright (C) ARM Limited 1998. All rights reserved.
- */
-#include <asm-generic/sizes.h>
-
-#define SZ_48M (SZ_32M + SZ_16M)
*/
extern void platform_smp_prepare_cpus(unsigned int);
+/*
+ * Logical CPU mapping.
+ */
+extern int __cpu_logical_map[NR_CPUS];
+#define cpu_logical_map(cpu) __cpu_logical_map[cpu]
+
/*
* Initial data for bringing up a secondary CPU.
*/
#ifndef __ASSEMBLY__
+#include <linux/compiler.h>
#include <linux/linkage.h>
#include <linux/irqflags.h>
extern void show_pte(struct mm_struct *mm, unsigned long addr);
extern void __show_regs(struct pt_regs *);
-extern int cpu_architecture(void);
+extern int __pure cpu_architecture(void);
extern void cpu_init(void);
void arm_machine_restart(char mode, const char *cmd);
#define pte_free_tlb(tlb, ptep, addr) __pte_free_tlb(tlb, ptep, addr)
#define pmd_free_tlb(tlb, pmdp, addr) pmd_free((tlb)->mm, pmdp)
+#define pud_free_tlb(tlb, pudp, addr) pud_free((tlb)->mm, pudp)
#define tlb_migrate_finish(mm) do { } while (0)
#ifndef _ASM_ARM_TOPOLOGY_H
#define _ASM_ARM_TOPOLOGY_H
+#ifdef CONFIG_ARM_CPU_TOPOLOGY
+
+#include <linux/cpumask.h>
+
+struct cputopo_arm {
+ int thread_id;
+ int core_id;
+ int socket_id;
+ cpumask_t thread_sibling;
+ cpumask_t core_sibling;
+};
+
+extern struct cputopo_arm cpu_topology[NR_CPUS];
+
+#define topology_physical_package_id(cpu) (cpu_topology[cpu].socket_id)
+#define topology_core_id(cpu) (cpu_topology[cpu].core_id)
+#define topology_core_cpumask(cpu) (&cpu_topology[cpu].core_sibling)
+#define topology_thread_cpumask(cpu) (&cpu_topology[cpu].thread_sibling)
+
+#define mc_capable() (cpu_topology[0].socket_id != -1)
+#define smt_capable() (cpu_topology[0].thread_id != -1)
+
+void init_cpu_topology(void);
+void store_cpu_topology(unsigned int cpuid);
+const struct cpumask *cpu_coregroup_mask(unsigned int cpu);
+
+#else
+
+static inline void init_cpu_topology(void) { }
+static inline void store_cpu_topology(unsigned int cpuid) { }
+
+#endif
+
#include <asm-generic/topology.h>
#endif /* _ASM_ARM_TOPOLOGY_H */
obj-$(CONFIG_CPU_HAS_PMU) += pmu.o
obj-$(CONFIG_HW_PERF_EVENTS) += perf_event.o
AFLAGS_iwmmxt.o := -Wa,-mcpu=iwmmxt
+obj-$(CONFIG_ARM_CPU_TOPOLOGY) += topology.o
ifneq ($(CONFIG_ARCH_EBSA110),y)
obj-y += io.o
memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (IO_SIZE / PGDIR_SIZE));
- src_pgd = pgd_offset(mm, EASI_BASE);
+ src_pgd = pgd_offset(mm, (unsigned long)EASI_BASE);
dst_pgd = pgd_offset(mm, EASI_START);
memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
#define ecard_probeirqhw() (0)
#endif
-#ifndef IO_EC_MEMC8_BASE
-#define IO_EC_MEMC8_BASE 0
-#endif
-
-static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
+static void __iomem *__ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
{
- unsigned long address = 0;
+ void __iomem *address = NULL;
int slot = ec->slot_no;
if (ec->slot_no == 8)
- return IO_EC_MEMC8_BASE;
+ return ECARD_MEMC8_BASE;
ectcr &= ~(1 << slot);
switch (type) {
case ECARD_MEMC:
if (slot < 4)
- address = IO_EC_MEMC_BASE + (slot << 12);
+ address = ECARD_MEMC_BASE + (slot << 14);
break;
case ECARD_IOC:
if (slot < 4)
- address = IO_EC_IOC_BASE + (slot << 12);
-#ifdef IO_EC_IOC4_BASE
+ address = ECARD_IOC_BASE + (slot << 14);
else
- address = IO_EC_IOC4_BASE + ((slot - 4) << 12);
-#endif
+ address = ECARD_IOC4_BASE + ((slot - 4) << 14);
if (address)
- address += speed << 17;
+ address += speed << 19;
break;
-#ifdef IO_EC_EASI_BASE
case ECARD_EASI:
- address = IO_EC_EASI_BASE + (slot << 22);
+ address = ECARD_EASI_BASE + (slot << 24);
if (speed == ECARD_FAST)
ectcr |= 1 << slot;
break;
-#endif
+
default:
break;
}
ecard_t **ecp;
ecard_t *ec;
struct ex_ecid cid;
+ void __iomem *addr;
int i, rc;
ec = ecard_alloc_card(type, slot);
}
rc = -ENODEV;
- if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0)
+ if ((addr = __ecard_address(ec, type, ECARD_SYNC)) == NULL)
goto nodev;
cid.r_zero = 1;
ec->cid.fiqmask = cid.r_fiqmask;
ec->cid.fiqoff = ecard_gets24(cid.r_fiqoff);
ec->fiqaddr =
- ec->irqaddr = (void __iomem *)ioaddr(ec->podaddr);
+ ec->irqaddr = addr;
if (ec->cid.is) {
ec->irqmask = ec->cid.irqmask;
set_irq_flags(ec->irq, IRQF_VALID);
}
-#ifdef IO_EC_MEMC8_BASE
if (slot == 8)
ec->irq = 11;
-#endif
#ifdef CONFIG_ARCH_RPC
/* On RiscPC, only first two slots have DMA capability */
if (slot < 2)
ecard_probe(slot, ECARD_IOC);
}
-#ifdef IO_EC_MEMC8_BASE
ecard_probe(8, ECARD_IOC);
-#endif
irqhw = ecard_probeirqhw();
#include <asm/unwind.h>
#include <asm/unistd.h>
#include <asm/tls.h>
+#include <asm/system.h>
#include "entry-header.S"
#include <asm/entry-macro-multi.S>
ldr r0, [r4, #-4]
#else
ldrh r0, [r4, #-2] @ Thumb instruction at LR - 2
- and r9, r0, #0xf800
- cmp r9, #0xe800 @ 32-bit instruction if xx >= 0
+ cmp r0, #0xe800 @ 32-bit instruction if xx >= 0
ldrhhs r9, [r4] @ bottom 16 bits
orrhs r0, r9, r0, lsl #16
#endif
#endif
beq call_fpe
@ Thumb instruction
-#if __LINUX_ARM_ARCH__ >= 7
+#if CONFIG_ARM_THUMB && __LINUX_ARM_ARCH__ >= 6 && CONFIG_CPU_V7
+/*
+ * Thumb-2 instruction handling. Note that because pre-v6 and >= v6 platforms
+ * can never be supported in a single kernel, this code is not applicable at
+ * all when __LINUX_ARM_ARCH__ < 6. This allows simplifying assumptions to be
+ * made about .arch directives.
+ */
+#if __LINUX_ARM_ARCH__ < 7
+/* If the target CPU may not be Thumb-2-capable, a run-time check is needed: */
+#define NEED_CPU_ARCHITECTURE
+ ldr r5, .LCcpu_architecture
+ ldr r5, [r5]
+ cmp r5, #CPU_ARCH_ARMv7
+ blo __und_usr_unknown
+/*
+ * The following code won't get run unless the running CPU really is v7, so
+ * coding round the lack of ldrht on older arches is pointless. Temporarily
+ * override the assembler target arch with the minimum required instead:
+ */
+ .arch armv6t2
+#endif
2:
ARM( ldrht r5, [r4], #2 )
THUMB( ldrht r5, [r4] )
THUMB( add r4, r4, #2 )
- and r0, r5, #0xf800 @ mask bits 111x x... .... ....
- cmp r0, #0xe800 @ 32bit instruction if xx != 0
+ cmp r5, #0xe800 @ 32bit instruction if xx != 0
blo __und_usr_unknown
3: ldrht r0, [r4]
add r2, r2, #2 @ r2 is PC + 2, make it PC + 4
orr r0, r0, r5, lsl #16
+
+#if __LINUX_ARM_ARCH__ < 7
+/* If the target arch was overridden, change it back: */
+#ifdef CONFIG_CPU_32v6K
+ .arch armv6k
#else
+ .arch armv6
+#endif
+#endif /* __LINUX_ARM_ARCH__ < 7 */
+#else /* !(CONFIG_ARM_THUMB && __LINUX_ARM_ARCH__ >= 6 && CONFIG_CPU_V7) */
b __und_usr_unknown
#endif
UNWIND(.fnend )
movw_pc lr @ CP#14 (Debug)
movw_pc lr @ CP#15 (Control)
+#ifdef NEED_CPU_ARCHITECTURE
+ .align 2
+.LCcpu_architecture:
+ .word __cpu_architecture
+#endif
+
#ifdef CONFIG_NEON
.align 6
#include <asm/memory.h>
#include <asm/thread_info.h>
#include <asm/system.h>
+#include <asm/pgtable.h>
#ifdef CONFIG_DEBUG_LL
#include <mach/debug-macro.S>
#error KERNEL_RAM_VADDR must start at 0xXXXX8000
#endif
+#define PG_DIR_SIZE 0x4000
+#define PMD_ORDER 2
+
.globl swapper_pg_dir
- .equ swapper_pg_dir, KERNEL_RAM_VADDR - 0x4000
+ .equ swapper_pg_dir, KERNEL_RAM_VADDR - PG_DIR_SIZE
.macro pgtbl, rd, phys
- add \rd, \phys, #TEXT_OFFSET - 0x4000
+ add \rd, \phys, #TEXT_OFFSET - PG_DIR_SIZE
.endm
#ifdef CONFIG_XIP_KERNEL
pgtbl r4, r8 @ page table address
/*
- * Clear the 16K level 1 swapper page table
+ * Clear the swapper page table
*/
mov r0, r4
mov r3, #0
- add r6, r0, #0x4000
+ add r6, r0, #PG_DIR_SIZE
1: str r3, [r0], #4
str r3, [r0], #4
str r3, [r0], #4
sub r0, r0, r3 @ virt->phys offset
add r5, r5, r0 @ phys __enable_mmu
add r6, r6, r0 @ phys __enable_mmu_end
- mov r5, r5, lsr #20
- mov r6, r6, lsr #20
+ mov r5, r5, lsr #SECTION_SHIFT
+ mov r6, r6, lsr #SECTION_SHIFT
-1: orr r3, r7, r5, lsl #20 @ flags + kernel base
- str r3, [r4, r5, lsl #2] @ identity mapping
- teq r5, r6
- addne r5, r5, #1 @ next section
- bne 1b
+1: orr r3, r7, r5, lsl #SECTION_SHIFT @ flags + kernel base
+ str r3, [r4, r5, lsl #PMD_ORDER] @ identity mapping
+ cmp r5, r6
+ addlo r5, r5, #1 @ next section
+ blo 1b
/*
* Now setup the pagetables for our kernel direct
* mapped region.
*/
mov r3, pc
- mov r3, r3, lsr #20
- orr r3, r7, r3, lsl #20
- add r0, r4, #(KERNEL_START & 0xff000000) >> 18
- str r3, [r0, #(KERNEL_START & 0x00f00000) >> 18]!
+ mov r3, r3, lsr #SECTION_SHIFT
+ orr r3, r7, r3, lsl #SECTION_SHIFT
+ add r0, r4, #(KERNEL_START & 0xff000000) >> (SECTION_SHIFT - PMD_ORDER)
+ str r3, [r0, #((KERNEL_START & 0x00f00000) >> SECTION_SHIFT) << PMD_ORDER]!
ldr r6, =(KERNEL_END - 1)
- add r0, r0, #4
- add r6, r4, r6, lsr #18
+ add r0, r0, #1 << PMD_ORDER
+ add r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ORDER)
1: cmp r0, r6
- add r3, r3, #1 << 20
- strls r3, [r0], #4
+ add r3, r3, #1 << SECTION_SHIFT
+ strls r3, [r0], #1 << PMD_ORDER
bls 1b
#ifdef CONFIG_XIP_KERNEL
*/
add r3, r8, #TEXT_OFFSET
orr r3, r3, r7
- add r0, r4, #(KERNEL_RAM_VADDR & 0xff000000) >> 18
- str r3, [r0, #(KERNEL_RAM_VADDR & 0x00f00000) >> 18]!
+ add r0, r4, #(KERNEL_RAM_VADDR & 0xff000000) >> (SECTION_SHIFT - PMD_ORDER)
+ str r3, [r0, #(KERNEL_RAM_VADDR & 0x00f00000) >> (SECTION_SHIFT - PMD_ORDER)]!
ldr r6, =(_end - 1)
add r0, r0, #4
- add r6, r4, r6, lsr #18
+ add r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ORDER)
1: cmp r0, r6
add r3, r3, #1 << 20
strls r3, [r0], #4
* Then map boot params address in r2 or
* the first 1MB of ram if boot params address is not specified.
*/
- mov r0, r2, lsr #20
- movs r0, r0, lsl #20
+ mov r0, r2, lsr #SECTION_SHIFT
+ movs r0, r0, lsl #SECTION_SHIFT
moveq r0, r8
sub r3, r0, r8
add r3, r3, #PAGE_OFFSET
- add r3, r4, r3, lsr #18
+ add r3, r4, r3, lsr #(SECTION_SHIFT - PMD_ORDER)
orr r6, r7, r0
str r6, [r3]
*/
addruart r7, r3
- mov r3, r3, lsr #20
- mov r3, r3, lsl #2
+ mov r3, r3, lsr #SECTION_SHIFT
+ mov r3, r3, lsl #PMD_ORDER
add r0, r4, r3
rsb r3, r3, #0x4000 @ PTRS_PER_PGD*sizeof(long)
cmp r3, #0x0800 @ limit to 512MB
movhi r3, #0x0800
add r6, r0, r3
- mov r3, r7, lsr #20
+ mov r3, r7, lsr #SECTION_SHIFT
ldr r7, [r10, #PROCINFO_IO_MMUFLAGS] @ io_mmuflags
- orr r3, r7, r3, lsl #20
+ orr r3, r7, r3, lsl #SECTION_SHIFT
1: str r3, [r0], #4
- add r3, r3, #1 << 20
- teq r0, r6
- bne 1b
+ add r3, r3, #1 << SECTION_SHIFT
+ cmp r0, r6
+ blo 1b
#else /* CONFIG_DEBUG_ICEDCC */
/* we don't need any serial debugging mappings for ICEDCC */
* If we're using the NetWinder or CATS, we also need to map
* in the 16550-type serial port for the debug messages
*/
- add r0, r4, #0xff000000 >> 18
+ add r0, r4, #0xff000000 >> (SECTION_SHIFT - PMD_ORDER)
orr r3, r7, #0x7c000000
str r3, [r0]
#endif
* Similar reasons here - for debug. This is
* only for Acorn RiscPC architectures.
*/
- add r0, r4, #0x02000000 >> 18
+ add r0, r4, #0x02000000 >> (SECTION_SHIFT - PMD_ORDER)
orr r3, r7, #0x02000000
str r3, [r0]
- add r0, r4, #0xd8000000 >> 18
+ add r0, r4, #0xd8000000 >> (SECTION_SHIFT - PMD_ORDER)
str r3, [r0]
#endif
#endif
add r5, r5, r3 @ adjust table end address
add r7, r7, r3 @ adjust __pv_phys_offset address
str r8, [r7] @ save computed PHYS_OFFSET to __pv_phys_offset
-#ifndef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
mov r6, r3, lsr #24 @ constant for add/sub instructions
teq r3, r6, lsl #24 @ must be 16MiB aligned
-#else
- mov r6, r3, lsr #16 @ constant for add/sub instructions
- teq r3, r6, lsl #16 @ must be 64kiB aligned
-#endif
THUMB( it ne @ cross section branch )
bne __error
str r6, [r7, #4] @ save to __pv_offset
.text
__fixup_a_pv_table:
#ifdef CONFIG_THUMB2_KERNEL
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- lsls r0, r6, #24
- lsr r6, #8
- beq 1f
- clz r7, r0
- lsr r0, #24
- lsl r0, r7
- bic r0, 0x0080
- lsrs r7, #1
- orrcs r0, #0x0080
- orr r0, r0, r7, lsl #12
-#endif
-1: lsls r6, #24
- beq 4f
+ lsls r6, #24
+ beq 2f
clz r7, r6
lsr r6, #24
lsl r6, r7
orrcs r6, #0x0080
orr r6, r6, r7, lsl #12
orr r6, #0x4000
- b 4f
-2: @ at this point the C flag is always clear
- add r7, r3
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- ldrh ip, [r7]
- tst ip, 0x0400 @ the i bit tells us LS or MS byte
- beq 3f
- cmp r0, #0 @ set C flag, and ...
- biceq ip, 0x0400 @ immediate zero value has a special encoding
- streqh ip, [r7] @ that requires the i bit cleared
-#endif
-3: ldrh ip, [r7, #2]
+ b 2f
+1: add r7, r3
+ ldrh ip, [r7, #2]
and ip, 0x8f00
- orrcc ip, r6 @ mask in offset bits 31-24
- orrcs ip, r0 @ mask in offset bits 23-16
+ orr ip, r6 @ mask in offset bits 31-24
strh ip, [r7, #2]
-4: cmp r4, r5
+2: cmp r4, r5
ldrcc r7, [r4], #4 @ use branch for delay slot
- bcc 2b
+ bcc 1b
bx lr
#else
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- and r0, r6, #255 @ offset bits 23-16
- mov r6, r6, lsr #8 @ offset bits 31-24
-#else
- mov r0, #0 @ just in case...
-#endif
- b 3f
-2: ldr ip, [r7, r3]
+ b 2f
+1: ldr ip, [r7, r3]
bic ip, ip, #0x000000ff
- tst ip, #0x400 @ rotate shift tells us LS or MS byte
- orrne ip, ip, r6 @ mask in offset bits 31-24
- orreq ip, ip, r0 @ mask in offset bits 23-16
+ orr ip, ip, r6 @ mask in offset bits 31-24
str ip, [r7, r3]
-3: cmp r4, r5
+2: cmp r4, r5
ldrcc r7, [r4], #4 @ use branch for delay slot
- bcc 2b
+ bcc 1b
mov pc, lr
#endif
ENDPROC(__fixup_a_pv_table)
* recompiling the whole kernel when CONFIG_XIP_KERNEL is turned on/off.
*/
#undef MODULES_VADDR
-#define MODULES_VADDR (((unsigned long)_etext + ~PGDIR_MASK) & PGDIR_MASK)
+#define MODULES_VADDR (((unsigned long)_etext + ~PMD_MASK) & PMD_MASK)
#endif
#ifdef CONFIG_MMU
#include <linux/fs.h>
#include <linux/proc_fs.h>
#include <linux/memblock.h>
+#include <linux/bug.h>
+#include <linux/compiler.h>
#include <asm/unified.h>
#include <asm/cpu.h>
#include <asm/cacheflush.h>
#include <asm/cachetype.h>
#include <asm/tlbflush.h>
+#include <asm/system.h>
#include <asm/prom.h>
#include <asm/mach/arch.h>
EXPORT_SYMBOL(outer_cache);
#endif
+/*
+ * Cached cpu_architecture() result for use by assembler code.
+ * C code should use the cpu_architecture() function instead of accessing this
+ * variable directly.
+ */
+int __cpu_architecture __read_mostly = CPU_ARCH_UNKNOWN;
+
struct stack {
u32 irq[3];
u32 abt[3];
"?(17)",
};
-int cpu_architecture(void)
+static int __get_cpu_architecture(void)
{
int cpu_arch;
return cpu_arch;
}
+int __pure cpu_architecture(void)
+{
+ BUG_ON(__cpu_architecture == CPU_ARCH_UNKNOWN);
+
+ return __cpu_architecture;
+}
+
static int cpu_has_aliasing_icache(unsigned int arch)
{
int aliasing_icache;
}
cpu_name = list->cpu_name;
+ __cpu_architecture = __get_cpu_architecture();
#ifdef MULTI_CPU
processor = *list->proc;
if (__atags_pointer)
tags = phys_to_virt(__atags_pointer);
- else if (mdesc->boot_params) {
-#ifdef CONFIG_MMU
- /*
- * We still are executing with a minimal MMU mapping created
- * with the presumption that the machine default for this
- * is located in the first MB of RAM. Anything else will
- * fault and silently hang the kernel at this point.
- */
- if (mdesc->boot_params < PHYS_OFFSET ||
- mdesc->boot_params >= PHYS_OFFSET + SZ_1M) {
- printk(KERN_WARNING
- "Default boot params at physical 0x%08lx out of reach\n",
- mdesc->boot_params);
- } else
-#endif
- {
- tags = phys_to_virt(mdesc->boot_params);
- }
- }
+ else if (mdesc->atag_offset)
+ tags = (void *)(PAGE_OFFSET + mdesc->atag_offset);
#if defined(CONFIG_DEPRECATED_PARAM_STRUCT)
/*
#include <asm/cacheflush.h>
#include <asm/cpu.h>
#include <asm/cputype.h>
+#include <asm/topology.h>
#include <asm/mmu_context.h>
#include <asm/pgtable.h>
#include <asm/pgalloc.h>
#include <asm/tlbflush.h>
#include <asm/ptrace.h>
#include <asm/localtimer.h>
+#include <asm/smp_plat.h>
/*
* as from 2.5, kernels no longer have an init_tasks structure
}
#endif /* CONFIG_HOTPLUG_CPU */
+int __cpu_logical_map[NR_CPUS];
+
+void __init smp_setup_processor_id(void)
+{
+ int i;
+ u32 cpu = is_smp() ? read_cpuid_mpidr() & 0xff : 0;
+
+ cpu_logical_map(0) = cpu;
+ for (i = 1; i < NR_CPUS; ++i)
+ cpu_logical_map(i) = i == cpu ? 0 : i;
+
+ printk(KERN_INFO "Booting Linux on physical CPU %d\n", cpu);
+}
+
/*
* Called by both boot and secondaries to move global data into
* per-processor storage.
struct cpuinfo_arm *cpu_info = &per_cpu(cpu_data, cpuid);
cpu_info->loops_per_jiffy = loops_per_jiffy;
+
+ store_cpu_topology(cpuid);
}
/*
{
unsigned int ncores = num_possible_cpus();
+ init_cpu_topology();
+
smp_store_cpu_info(smp_processor_id());
/*
--- /dev/null
+/*
+ * arch/arm/kernel/topology.c
+ *
+ * Copyright (C) 2011 Linaro Limited.
+ * Written by: Vincent Guittot
+ *
+ * based on arch/sh/kernel/topology.c
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/cpu.h>
+#include <linux/cpumask.h>
+#include <linux/init.h>
+#include <linux/percpu.h>
+#include <linux/node.h>
+#include <linux/nodemask.h>
+#include <linux/sched.h>
+
+#include <asm/cputype.h>
+#include <asm/topology.h>
+
+#define MPIDR_SMP_BITMASK (0x3 << 30)
+#define MPIDR_SMP_VALUE (0x2 << 30)
+
+#define MPIDR_MT_BITMASK (0x1 << 24)
+
+/*
+ * These masks reflect the current use of the affinity levels.
+ * The affinity level can be up to 16 bits according to ARM ARM
+ */
+
+#define MPIDR_LEVEL0_MASK 0x3
+#define MPIDR_LEVEL0_SHIFT 0
+
+#define MPIDR_LEVEL1_MASK 0xF
+#define MPIDR_LEVEL1_SHIFT 8
+
+#define MPIDR_LEVEL2_MASK 0xFF
+#define MPIDR_LEVEL2_SHIFT 16
+
+struct cputopo_arm cpu_topology[NR_CPUS];
+
+const struct cpumask *cpu_coregroup_mask(unsigned int cpu)
+{
+ return &cpu_topology[cpu].core_sibling;
+}
+
+/*
+ * store_cpu_topology is called at boot when only one cpu is running
+ * and with the mutex cpu_hotplug.lock locked, when several cpus have booted,
+ * which prevents simultaneous write access to cpu_topology array
+ */
+void store_cpu_topology(unsigned int cpuid)
+{
+ struct cputopo_arm *cpuid_topo = &cpu_topology[cpuid];
+ unsigned int mpidr;
+ unsigned int cpu;
+
+ /* If the cpu topology has been already set, just return */
+ if (cpuid_topo->core_id != -1)
+ return;
+
+ mpidr = read_cpuid_mpidr();
+
+ /* create cpu topology mapping */
+ if ((mpidr & MPIDR_SMP_BITMASK) == MPIDR_SMP_VALUE) {
+ /*
+ * This is a multiprocessor system
+ * multiprocessor format & multiprocessor mode field are set
+ */
+
+ if (mpidr & MPIDR_MT_BITMASK) {
+ /* core performance interdependency */
+ cpuid_topo->thread_id = (mpidr >> MPIDR_LEVEL0_SHIFT)
+ & MPIDR_LEVEL0_MASK;
+ cpuid_topo->core_id = (mpidr >> MPIDR_LEVEL1_SHIFT)
+ & MPIDR_LEVEL1_MASK;
+ cpuid_topo->socket_id = (mpidr >> MPIDR_LEVEL2_SHIFT)
+ & MPIDR_LEVEL2_MASK;
+ } else {
+ /* largely independent cores */
+ cpuid_topo->thread_id = -1;
+ cpuid_topo->core_id = (mpidr >> MPIDR_LEVEL0_SHIFT)
+ & MPIDR_LEVEL0_MASK;
+ cpuid_topo->socket_id = (mpidr >> MPIDR_LEVEL1_SHIFT)
+ & MPIDR_LEVEL1_MASK;
+ }
+ } else {
+ /*
+ * This is an uniprocessor system
+ * we are in multiprocessor format but uniprocessor system
+ * or in the old uniprocessor format
+ */
+ cpuid_topo->thread_id = -1;
+ cpuid_topo->core_id = 0;
+ cpuid_topo->socket_id = -1;
+ }
+
+ /* update core and thread sibling masks */
+ for_each_possible_cpu(cpu) {
+ struct cputopo_arm *cpu_topo = &cpu_topology[cpu];
+
+ if (cpuid_topo->socket_id == cpu_topo->socket_id) {
+ cpumask_set_cpu(cpuid, &cpu_topo->core_sibling);
+ if (cpu != cpuid)
+ cpumask_set_cpu(cpu,
+ &cpuid_topo->core_sibling);
+
+ if (cpuid_topo->core_id == cpu_topo->core_id) {
+ cpumask_set_cpu(cpuid,
+ &cpu_topo->thread_sibling);
+ if (cpu != cpuid)
+ cpumask_set_cpu(cpu,
+ &cpuid_topo->thread_sibling);
+ }
+ }
+ }
+ smp_wmb();
+
+ printk(KERN_INFO "CPU%u: thread %d, cpu %d, socket %d, mpidr %x\n",
+ cpuid, cpu_topology[cpuid].thread_id,
+ cpu_topology[cpuid].core_id,
+ cpu_topology[cpuid].socket_id, mpidr);
+}
+
+/*
+ * init_cpu_topology is called at boot when only one cpu is running
+ * which prevent simultaneous write access to cpu_topology array
+ */
+void init_cpu_topology(void)
+{
+ unsigned int cpu;
+
+ /* init core mask */
+ for_each_possible_cpu(cpu) {
+ struct cputopo_arm *cpu_topo = &(cpu_topology[cpu]);
+
+ cpu_topo->thread_id = -1;
+ cpu_topo->core_id = -1;
+ cpu_topo->socket_id = -1;
+ cpumask_clear(&cpu_topo->core_sibling);
+ cpumask_clear(&cpu_topo->thread_sibling);
+ }
+ smp_wmb();
+}
# INITRD_PHYS must be in RAM
ifeq ($(CONFIG_ARCH_AT91CAP9),y)
- zreladdr-y := 0x70008000
+ zreladdr-y += 0x70008000
params_phys-y := 0x70000100
initrd_phys-y := 0x70410000
else ifeq ($(CONFIG_ARCH_AT91SAM9G45),y)
- zreladdr-y := 0x70008000
+ zreladdr-y += 0x70008000
params_phys-y := 0x70000100
initrd_phys-y := 0x70410000
else
- zreladdr-y := 0x20008000
+ zreladdr-y += 0x20008000
params_phys-y := 0x20000100
initrd_phys-y := 0x20410000
endif
#include <asm/mach/irq.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <mach/board.h>
#include <mach/cpu.h>
-#include <mach/gpio.h>
#include <mach/at91cap9.h>
#include <mach/at91cap9_matrix.h>
#include <mach/at91sam9_smc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200.h>
#include <mach/at91rm9200_mc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include <mach/at91sam9260.h>
#include <mach/at91sam9260_matrix.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9261.h>
#include <mach/at91sam9261_matrix.h>
#include <mach/at91sam9_smc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9263.h>
#include <mach/at91sam9263_matrix.h>
#include <mach/at91sam9_smc.h>
#include <linux/module.h>
#include <linux/pm.h>
+#include <linux/dma-mapping.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
static void __init at91sam9g45_map_io(void)
{
at91_init_sram(0, AT91SAM9G45_SRAM_BASE, AT91SAM9G45_SRAM_SIZE);
+ init_consistent_dma_size(SZ_4M);
}
static void __init at91sam9g45_initialize(void)
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <linux/atmel-mci.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9g45.h>
#include <mach/at91sam9g45_matrix.h>
#include <mach/at91sam9_smc.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
#include <video/atmel_lcdc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9rl.h>
#include <mach/at91sam9rl_matrix.h>
#include <mach/at91sam9_smc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/map.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91cap9_matrix.h>
#include <mach/at91sam9_smc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91sam9260_matrix.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include <mach/cpu.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
#include <linux/types.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include <mach/at91rm9200_mc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include "generic.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include "sam9_smc.h"
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
#include <mach/system_rev.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/at91_shdwc.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <mach/hardware.h>
#include <mach/board.h>
-#include <mach/gpio.h>
#include <mach/at91rm9200_mc.h>
#include <mach/cpu.h>
#include <linux/clk.h>
#include <linux/errno.h>
+#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/debugfs.h>
#include <mach/hardware.h>
#include <mach/at91_pio.h>
-#include <mach/gpio.h>
-
-#include <asm/gpio.h>
#include "generic.h"
#define AT91SAM9G45_EHCI_BASE 0x00800000 /* USB Host controller (EHCI) */
#define AT91SAM9G45_VDEC_BASE 0x00900000 /* Video Decoder Controller */
-#define CONSISTENT_DMA_SIZE SZ_4M
-
/*
* DMA peripheral identifiers
* for hardware handshaking interface
*/
#include <asm/errno.h>
-#include <asm-generic/gpio.h> /* cansleep wrappers */
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
#define gpio_to_irq(gpio) (gpio)
#define irq_to_gpio(irq) (irq)
* 2 of the License, or (at your option) any later version.
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <mach/board.h>
-#include <mach/gpio.h>
/* ------------------------------------------------------------------------- */
* (at your option) any later version.
*/
+#include <linux/gpio.h>
#include <linux/suspend.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <asm/mach/irq.h>
#include <mach/at91_pmc.h>
-#include <mach/gpio.h>
#include <mach/cpu.h>
#include "generic.h"
# Address where decompressor will be written and eventually executed.
#
# default to SDRAM
-zreladdr-y := $(CONFIG_BCM_ZRELADDR)
+zreladdr-y += $(CONFIG_BCM_ZRELADDR)
params_phys-y := 0x00000800
#define PLAT_PHYS_OFFSET CFG_GLOBAL_RAM_BASE
-/*
- * Maximum DMA memory allowed is 14M
- */
-#define CONSISTENT_DMA_SIZE (SZ_16M - SZ_2M)
-
#endif
*****************************************************************************/
#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
#include <asm/mach/map.h>
#include <mach/hardware.h>
{
iotable_init(bcmring_io_desc, ARRAY_SIZE(bcmring_io_desc));
+ /* Maximum DMA memory allowed is 14M */
+ init_consistent_dma_size(14 << 20);
}
# The standard locations for stuff on CLPS711x type processors
- zreladdr-y := 0xc0028000
+ zreladdr-y += 0xc0028000
params_phys-y := 0xc0000100
# Should probably have some agreement on these...
initrd_phys-$(CONFIG_ARCH_P720T) := 0xc0400000
MACHINE_START(AUTCPU12, "autronix autcpu12")
/* Maintainer: Thomas Gleixner */
- .boot_params = 0xc0020000,
+ .atag_offset = 0x20000,
.map_io = autcpu12_map_io,
.init_irq = clps711x_init_irq,
.timer = &clps711x_timer,
MACHINE_START(CDB89712, "Cirrus-CDB89712")
/* Maintainer: Ray Lehtiniemi */
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = cdb89712_map_io,
.init_irq = clps711x_init_irq,
.timer = &clps711x_timer,
MACHINE_START(CEIVA, "CEIVA/Polaroid Photo MAX Digital Picture Frame")
/* Maintainer: Rob Scott */
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = ceiva_map_io,
.init_irq = clps711x_init_irq,
.timer = &clps711x_timer,
MACHINE_START(CLEP7212, "Cirrus Logic 7212/7312")
/* Maintainer: Nobody */
- .boot_params = 0xc0000100,
+ .atag_offset = 0x0100,
.fixup = fixup_clep7312,
.map_io = clps711x_map_io,
.init_irq = clps711x_init_irq,
MACHINE_START(EDB7211, "CL-EDB7211 (EP7211 eval board)")
/* Maintainer: Jon McClintock */
- .boot_params = 0xc0020100, /* 0xc0000000 - 0xc001ffff can be video RAM */
+ .atag_offset = 0x20100, /* 0xc0000000 - 0xc001ffff can be video RAM */
.fixup = fixup_edb7211,
.map_io = edb7211_map_io,
.reserve = edb7211_reserve,
MACHINE_START(FORTUNET, "ARM-FortuNet")
/* Maintainer: FortuNet Inc. */
- .boot_params = 0x00000000,
.fixup = fortunet_fixup,
.map_io = clps711x_map_io,
.init_irq = clps711x_init_irq,
MACHINE_START(P720T, "ARM-Prospector720T")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.fixup = fixup_p720t,
.map_io = p720t_map_io,
.init_irq = clps711x_init_irq,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00C00000
}
MACHINE_START(CNS3420VB, "Cavium Networks CNS3420 Validation Board")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = cns3420_map_io,
.init_irq = cns3xxx_init_irq,
.timer = &cns3xxx_timer,
# Common objects
obj-y := time.o clock.o serial.o io.o psc.o \
- gpio.o dma.o usb.o common.o sram.o aemif.o
+ dma.o usb.o common.o sram.o aemif.o
obj-$(CONFIG_DAVINCI_MUX) += mux.o
obj-$(CONFIG_ARCH_DAVINCI_DA830) += da830.o devices-da8xx.o
obj-$(CONFIG_ARCH_DAVINCI_DA850) += da850.o devices-da8xx.o
obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += tnetv107x.o devices-tnetv107x.o
-obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o
obj-$(CONFIG_AINTC) += irq.o
obj-$(CONFIG_CP_INTC) += cp_intc.o
ifeq ($(CONFIG_ARCH_DAVINCI_DMx),y)
$(error Cannot enable DaVinci and DA8XX platforms concurrently)
else
- zreladdr-y := 0xc0008000
+ zreladdr-y += 0xc0008000
params_phys-y := 0xc0000100
initrd_phys-y := 0xc0800000
endif
else
- zreladdr-y := 0x80008000
+ zreladdr-y += 0x80008000
params_phys-y := 0x80000100
initrd_phys-y := 0x80800000
endif
}
MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
- .boot_params = (DA8XX_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = da830_evm_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
}
MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138/AM18x EVM")
- .boot_params = (DA8XX_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = da850_evm_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
}
MACHINE_START(DAVINCI_DM355_EVM, "DaVinci DM355 EVM")
- .boot_params = (0x80000100),
+ .atag_offset = 0x100,
.map_io = dm355_evm_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
}
MACHINE_START(DM355_LEOPARD, "DaVinci DM355 leopard")
- .boot_params = (0x80000100),
+ .atag_offset = 0x100,
.map_io = dm355_leopard_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
}
MACHINE_START(DAVINCI_DM365_EVM, "DaVinci DM365 EVM")
- .boot_params = (0x80000100),
+ .atag_offset = 0x100,
.map_io = dm365_evm_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
MACHINE_START(DAVINCI_EVM, "DaVinci DM644x EVM")
/* Maintainer: MontaVista Software <source@mvista.com> */
- .boot_params = (DAVINCI_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = davinci_evm_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
}
MACHINE_START(DAVINCI_DM6467_EVM, "DaVinci DM646x EVM")
- .boot_params = (0x80000100),
+ .atag_offset = 0x100,
.map_io = davinci_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
MACHINE_END
MACHINE_START(DAVINCI_DM6467TEVM, "DaVinci DM6467T EVM")
- .boot_params = (0x80000100),
+ .atag_offset = 0x100,
.map_io = davinci_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
}
MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
- .boot_params = (DA8XX_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = mityomapl138_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
MACHINE_START(NEUROS_OSD2, "Neuros OSD2")
/* Maintainer: Neuros Technologies <neuros@groups.google.com> */
- .boot_params = (DAVINCI_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = davinci_ntosd2_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
}
MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
- .boot_params = (DA8XX_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = omapl138_hawk_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
MACHINE_START(SFFSDR, "Lyrtech SFFSDR")
/* Maintainer: Hugo Villeneuve hugo.villeneuve@lyrtech.com */
- .boot_params = (DAVINCI_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = davinci_sffsdr_map_io,
.init_irq = davinci_irq_init,
.timer = &davinci_timer,
#endif
MACHINE_START(TNETV107X, "TNETV107X EVM")
- .boot_params = (TNETV107X_DDR_BASE + 0x100),
+ .atag_offset = 0x100,
.map_io = tnetv107x_init,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
#include <linux/io.h>
#include <linux/etherdevice.h>
#include <linux/davinci_emac.h>
+#include <linux/dma-mapping.h>
#include <asm/tlb.h>
#include <asm/mach/map.h>
iotable_init(davinci_soc_info.io_desc,
davinci_soc_info.io_desc_num);
+ init_consistent_dma_size(14 << 20);
+
/*
* Normally devicemaps_init() would flush caches and tlb after
* mdesc->map_io(), but we must also do it here because of the CPU
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <mach/common.h>
#include <mach/time.h>
#include <mach/da8xx.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <mach/da8xx.h>
#include <mach/cpufreq.h>
#include <mach/pm.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <mach/common.h>
#include <mach/asp.h>
#include <mach/spi.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <asm/mach/map.h>
#include <mach/asp.h>
#include <mach/keyscan.h>
#include <mach/spi.h>
-
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
#include <asm/mach/map.h>
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
#include <asm/mach/map.h>
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
--- /dev/null
+/*
+ * TI DaVinci GPIO Support
+ *
+ * Copyright (c) 2006 David Brownell
+ * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DAVINCI_DAVINCI_GPIO_H
+#define __DAVINCI_DAVINCI_GPIO_H
+
+#include <linux/io.h>
+#include <linux/spinlock.h>
+
+#include <asm-generic/gpio.h>
+
+#include <mach/irqs.h>
+#include <mach/common.h>
+
+#define DAVINCI_GPIO_BASE 0x01C67000
+
+enum davinci_gpio_type {
+ GPIO_TYPE_DAVINCI = 0,
+ GPIO_TYPE_TNETV107X,
+};
+
+/*
+ * basic gpio routines
+ *
+ * board-specific init should be done by arch/.../.../board-XXX.c (maybe
+ * initializing banks together) rather than boot loaders; kexec() won't
+ * go through boot loaders.
+ *
+ * the gpio clock will be turned on when gpios are used, and you may also
+ * need to pay attention to PINMUX registers to be sure those pins are
+ * used as gpios, not with other peripherals.
+ *
+ * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation,
+ * and maybe for later updates, code may write GPIO(N). These may be
+ * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip
+ * may not support all the GPIOs in that range.
+ *
+ * GPIOs can also be on external chips, numbered after the ones built-in
+ * to the DaVinci chip. For now, they won't be usable as IRQ sources.
+ */
+#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */
+
+/* Convert GPIO signal to GPIO pin number */
+#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio))
+
+struct davinci_gpio_controller {
+ struct gpio_chip chip;
+ int irq_base;
+ spinlock_t lock;
+ void __iomem *regs;
+ void __iomem *set_data;
+ void __iomem *clr_data;
+ void __iomem *in_data;
+};
+
+/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
+ * with constant parameters; or in outlined code they execute at runtime.
+ *
+ * You'd access the controller directly when reading or writing more than
+ * one gpio value at a time, and to support wired logic where the value
+ * being driven by the cpu need not match the value read back.
+ *
+ * These are NOT part of the cross-platform GPIO interface
+ */
+static inline struct davinci_gpio_controller *
+__gpio_to_controller(unsigned gpio)
+{
+ struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
+ int index = gpio / 32;
+
+ if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
+ return NULL;
+
+ return ctlrs + index;
+}
+
+static inline u32 __gpio_mask(unsigned gpio)
+{
+ return 1 << (gpio % 32);
+}
+
+#endif /* __DAVINCI_DAVINCI_GPIO_H */
#ifndef __DAVINCI_GPIO_H
#define __DAVINCI_GPIO_H
-#include <linux/io.h>
-#include <linux/spinlock.h>
-
#include <asm-generic/gpio.h>
-#include <mach/irqs.h>
-#include <mach/common.h>
-
-#define DAVINCI_GPIO_BASE 0x01C67000
-
-enum davinci_gpio_type {
- GPIO_TYPE_DAVINCI = 0,
- GPIO_TYPE_TNETV107X,
-};
-
-/*
- * basic gpio routines
- *
- * board-specific init should be done by arch/.../.../board-XXX.c (maybe
- * initializing banks together) rather than boot loaders; kexec() won't
- * go through boot loaders.
- *
- * the gpio clock will be turned on when gpios are used, and you may also
- * need to pay attention to PINMUX registers to be sure those pins are
- * used as gpios, not with other peripherals.
- *
- * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1). For documentation,
- * and maybe for later updates, code may write GPIO(N). These may be
- * all 1.8V signals, all 3.3V ones, or a mix of the two. A given chip
- * may not support all the GPIOs in that range.
- *
- * GPIOs can also be on external chips, numbered after the ones built-in
- * to the DaVinci chip. For now, they won't be usable as IRQ sources.
- */
-#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */
-
-/* Convert GPIO signal to GPIO pin number */
-#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio))
-
-struct davinci_gpio_controller {
- struct gpio_chip chip;
- int irq_base;
- spinlock_t lock;
- void __iomem *regs;
- void __iomem *set_data;
- void __iomem *clr_data;
- void __iomem *in_data;
-};
-
-/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
- * with constant parameters; or in outlined code they execute at runtime.
- *
- * You'd access the controller directly when reading or writing more than
- * one gpio value at a time, and to support wired logic where the value
- * being driven by the cpu need not match the value read back.
- *
- * These are NOT part of the cross-platform GPIO interface
- */
-static inline struct davinci_gpio_controller *
-__gpio_to_controller(unsigned gpio)
-{
- struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
- int index = gpio / 32;
-
- if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
- return NULL;
-
- return ctlrs + index;
-}
-
-static inline u32 __gpio_mask(unsigned gpio)
-{
- return 1 << (gpio % 32);
-}
+/* The inline versions use the static inlines in the driver header */
+#include "gpio-davinci.h"
/*
* The get/set/clear functions will inline when called with constant
return __gpio_cansleep(gpio);
}
-static inline int gpio_to_irq(unsigned gpio)
-{
- return __gpio_to_irq(gpio);
-}
-
static inline int irq_to_gpio(unsigned irq)
{
/* don't support the reverse mapping */
#define DDR2_MCLKSTOPEN_BIT BIT(30)
#define DDR2_LPMODEN_BIT BIT(31)
-/*
- * Increase size of DMA-consistent memory region
- */
-#define CONSISTENT_DMA_SIZE (14<<20)
-
#endif /* __ASM_ARCH_MEMORY_H */
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <mach/psc.h>
#include <mach/cp_intc.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/hardware.h>
#include <mach/tnetv107x.h>
+#include <mach/gpio-davinci.h>
#include "clock.h"
#include "mux.h"
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
}
MACHINE_START(CM_A510, "Compulab CM-A510 Board")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = cm_a510_init,
.map_io = dove_map_io,
.init_early = dove_init_early,
}
MACHINE_START(DOVE_DB, "Marvell DB-MV88AP510-BP Development Board")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = dove_db_init,
.map_io = dove_map_io,
.init_early = dove_init_early,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000400
initrd_phys-y := 0x00800000
MACHINE_START(EBSA110, "EBSA110")
/* Maintainer: Russell King */
- .boot_params = 0x00000400,
+ .atag_offset = 0x400,
.reserve_lp0 = 1,
.reserve_lp2 = 1,
.soft_reboot = 1,
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
u8 __inb8(unsigned int port);
void __outb8(u8 val, unsigned int port);
- zreladdr-$(CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET) := 0x00008000
+ zreladdr-$(CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET) += 0x00008000
params_phys-$(CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET) := 0x00000100
- zreladdr-$(CONFIG_EP93XX_SDCE0_PHYS_OFFSET) := 0xc0008000
+ zreladdr-$(CONFIG_EP93XX_SDCE0_PHYS_OFFSET) += 0xc0008000
params_phys-$(CONFIG_EP93XX_SDCE0_PHYS_OFFSET) := 0xc0000100
- zreladdr-$(CONFIG_EP93XX_SDCE1_PHYS_OFFSET) := 0xd0008000
+ zreladdr-$(CONFIG_EP93XX_SDCE1_PHYS_OFFSET) += 0xd0008000
params_phys-$(CONFIG_EP93XX_SDCE1_PHYS_OFFSET) := 0xd0000100
- zreladdr-$(CONFIG_EP93XX_SDCE2_PHYS_OFFSET) := 0xe0008000
+ zreladdr-$(CONFIG_EP93XX_SDCE2_PHYS_OFFSET) += 0xe0008000
params_phys-$(CONFIG_EP93XX_SDCE2_PHYS_OFFSET) := 0xe0000100
- zreladdr-$(CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET) := 0xf0008000
+ zreladdr-$(CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET) += 0xf0008000
params_phys-$(CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET) := 0xf0000100
MACHINE_START(ADSSPHERE, "ADS Sphere board")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9301
MACHINE_START(EDB9301, "Cirrus Logic EDB9301 Evaluation Board")
/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9302
MACHINE_START(EDB9302, "Cirrus Logic EDB9302 Evaluation Board")
/* Maintainer: George Kashperko <george@chas.com.ua> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9302A
MACHINE_START(EDB9302A, "Cirrus Logic EDB9302A Evaluation Board")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9307
MACHINE_START(EDB9307, "Cirrus Logic EDB9307 Evaluation Board")
/* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9307A
MACHINE_START(EDB9307A, "Cirrus Logic EDB9307A Evaluation Board")
/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
- .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9312
MACHINE_START(EDB9312, "Cirrus Logic EDB9312 Evaluation Board")
/* Maintainer: Toufeeq Hussain <toufeeq_hussain@infosys.com> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9315
MACHINE_START(EDB9315, "Cirrus Logic EDB9315 Evaluation Board")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_EDB9315A
MACHINE_START(EDB9315A, "Cirrus Logic EDB9315A Evaluation Board")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
MACHINE_START(GESBC9312, "Glomation GESBC-9312-sx")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
/* maximum value for irq capable line identifiers */
#define EP93XX_GPIO_LINE_MAX_IRQ EP93XX_GPIO_LINE_F(7)
-/* new generic GPIO API - see Documentation/gpio.txt */
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-
-/*
- * Map GPIO A0..A7 (0..7) to irq 64..71,
- * B0..B7 (7..15) to irq 72..79, and
- * F0..F7 (16..24) to irq 80..87.
- */
-#define gpio_to_irq(gpio) \
- (((gpio) <= EP93XX_GPIO_LINE_MAX_IRQ) ? (64 + (gpio)) : -EINVAL)
-
+#define gpio_to_irq __gpio_to_irq
#define irq_to_gpio(irq) ((irq) - gpio_to_irq(0))
#endif
#ifdef CONFIG_MACH_MICRO9H
MACHINE_START(MICRO9, "Contec Micro9-High")
/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_MICRO9M
MACHINE_START(MICRO9M, "Contec Micro9-Mid")
/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_MICRO9L
MACHINE_START(MICRO9L, "Contec Micro9-Lite")
/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
#ifdef CONFIG_MACH_MICRO9S
MACHINE_START(MICRO9S, "Contec Micro9-Slim")
/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
}
MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
-/* Maintainer: Ryan Mallon */
- .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100,
+ /* Maintainer: Ryan Mallon */
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
MACHINE_START(SNAPPER_CL15, "Bluewater Systems Snapper CL15")
/* Maintainer: Ryan Mallon */
- .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100,
+ .atag_offset = 0x100,
.map_io = ep93xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
MACHINE_START(TS72XX, "Technologic Systems TS-72xx SBC")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+ .atag_offset = 0x100,
.map_io = ts72xx_map_io,
.init_irq = ep93xx_init_irq,
.timer = &ep93xx_timer,
- zreladdr-y := 0x40008000
+ zreladdr-y += 0x40008000
params_phys-y := 0x40000100
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* Practically, GPIO banks up to GPZ are the configurable gpio banks */
/* GPIO bank sizes */
#define ARCH_NR_GPIOS (EXYNOS4_GPZ(EXYNOS4_GPIO_Z_NR) + \
CONFIG_SAMSUNG_GPIO_EXTRA + 1)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
MACHINE_START(ARMLEX4210, "ARMLEX4210")
/* Maintainer: Alim Akhtar <alim.akhtar@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = exynos4_init_irq,
.map_io = armlex4210_map_io,
.init_machine = armlex4210_machine_init,
MACHINE_START(NURI, "NURI")
/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = exynos4_init_irq,
.map_io = nuri_map_io,
.init_machine = nuri_machine_init,
MACHINE_START(SMDKC210, "SMDKC210")
/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = exynos4_init_irq,
.map_io = smdkc210_map_io,
.init_machine = smdkc210_machine_init,
MACHINE_START(SMDKV310, "SMDKV310")
/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
/* Maintainer: Changhwan Youn <chaos.youn@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = exynos4_init_irq,
.map_io = smdkv310_map_io,
.init_machine = smdkv310_machine_init,
MACHINE_START(UNIVERSAL_C210, "UNIVERSAL_C210")
/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = exynos4_init_irq,
.map_io = universal_map_io,
.init_machine = universal_machine_init,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
MACHINE_START(CATS, "Chalice-CATS")
/* Maintainer: Philip Blundell */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.soft_reboot = 1,
.fixup = fixup_cats,
.map_io = footbridge_map_io,
MACHINE_START(EBSA285, "EBSA285")
/* Maintainer: Russell King */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.video_start = 0x000a0000,
.video_end = 0x000bffff,
.map_io = footbridge_map_io,
#define PCIO_SIZE 0x00100000
#define PCIO_BASE MMU_IO(0xff000000, 0x7c000000)
-#define IO_SPACE_LIMIT 0xffff
-
/*
* Translation of various region addresses to virtual addresses
*/
MACHINE_START(NETWINDER, "Rebel-NetWinder")
/* Maintainer: Russell King/Rebel.com */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.video_start = 0x000a0000,
.video_end = 0x000bffff,
.reserve_lp0 = 1,
MACHINE_START(PERSONAL_SERVER, "Compaq-PersonalServer")
/* Maintainer: Jamey Hicks / George France */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = footbridge_map_io,
.init_irq = footbridge_init_irq,
.timer = &footbridge_timer,
ifeq ($(CONFIG_GEMINI_MEM_SWAP),y)
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
else
- zreladdr-y := 0x10008000
+ zreladdr-y += 0x10008000
params_phys-y := 0x10000100
initrd_phys-y := 0x10800000
endif
}
MACHINE_START(NAS4220B, "Raidsonic NAS IB-4220-B")
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = gemini_map_io,
.init_irq = gemini_init_irq,
.timer = &ib4220b_timer,
}
MACHINE_START(RUT100, "Teltonika RUT100")
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = gemini_map_io,
.init_irq = gemini_init_irq,
.timer = &rut1xx_timer,
}
MACHINE_START(WBD111, "Wiliboard WBD-111")
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = gemini_map_io,
.init_irq = gemini_init_irq,
.timer = &wbd111_timer,
}
MACHINE_START(WBD222, "Wiliboard WBD-222")
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = gemini_map_io,
.init_irq = gemini_init_irq,
.timer = &wbd222_timer,
#define __MACH_GPIO_H__
#include <mach/irqs.h>
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
#define gpio_to_irq(x) ((x) + GPIO_IRQ_BASE)
#define irq_to_gpio(x) ((x) - GPIO_IRQ_BASE)
- zreladdr-$(CONFIG_ARCH_H720X) := 0x40008000
+ zreladdr-$(CONFIG_ARCH_H720X) += 0x40008000
MACHINE_START(H7201, "Hynix GMS30C7201")
/* Maintainer: Robert Schwebel, Pengutronix */
- .boot_params = 0xc0001000,
+ .atag_offset = 0x1000,
.map_io = h720x_map_io,
.init_irq = h720x_init_irq,
.timer = &h7201_timer,
MACHINE_START(H7202, "Hynix HMS30C7202")
/* Maintainer: Robert Schwebel, Pengutronix */
- .boot_params = 0x40000100,
+ .atag_offset = 0x100,
.map_io = h720x_map_io,
.init_irq = h7202_init_irq,
.timer = &h7202_timer,
-zreladdr-$(CONFIG_ARCH_MX1) := 0x08008000
+zreladdr-$(CONFIG_ARCH_MX1) += 0x08008000
params_phys-$(CONFIG_ARCH_MX1) := 0x08000100
initrd_phys-$(CONFIG_ARCH_MX1) := 0x08800000
-zreladdr-$(CONFIG_MACH_MX21) := 0xC0008000
+zreladdr-$(CONFIG_MACH_MX21) += 0xC0008000
params_phys-$(CONFIG_MACH_MX21) := 0xC0000100
initrd_phys-$(CONFIG_MACH_MX21) := 0xC0800000
-zreladdr-$(CONFIG_ARCH_MX25) := 0x80008000
+zreladdr-$(CONFIG_ARCH_MX25) += 0x80008000
params_phys-$(CONFIG_ARCH_MX25) := 0x80000100
initrd_phys-$(CONFIG_ARCH_MX25) := 0x80800000
-zreladdr-$(CONFIG_MACH_MX27) := 0xA0008000
+zreladdr-$(CONFIG_MACH_MX27) += 0xA0008000
params_phys-$(CONFIG_MACH_MX27) := 0xA0000100
initrd_phys-$(CONFIG_MACH_MX27) := 0xA0800000
-zreladdr-$(CONFIG_ARCH_MX3) := 0x80008000
+zreladdr-$(CONFIG_ARCH_MX3) += 0x80008000
params_phys-$(CONFIG_ARCH_MX3) := 0x80000100
initrd_phys-$(CONFIG_ARCH_MX3) := 0x80800000
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <mach/hardware.h>
-#include <mach/gpio.h>
#include <mach/iomux-mx3.h>
/*
MACHINE_START(ARMADILLO5X0, "Armadillo-500")
/* Maintainer: Alberto Panizzo */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx31_map_io,
.init_early = imx31_init_early,
.init_irq = mx31_init_irq,
};
MACHINE_START(EUKREA_CPUIMX27, "EUKREA CPUIMX27")
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
MACHINE_START(EUKREA_CPUIMX35SD, "Eukrea CPUIMX35")
/* Maintainer: Eukrea Electromatique */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx35_map_io,
.init_early = imx35_init_early,
.init_irq = mx35_init_irq,
MACHINE_START(EUKREA_CPUIMX25SD, "Eukrea CPUIMX25")
/* Maintainer: Eukrea Electromatique */
- .boot_params = MX25_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx25_map_io,
.init_early = imx25_init_early,
.init_irq = mx25_init_irq,
};
MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10")
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
MACHINE_START(IMX27IPCAM, "Freescale IMX27IPCAM")
/* maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
};
MACHINE_START(IMX27LITE, "LogicPD i.MX27LITE")
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
};
MACHINE_START(KZM_ARM11_01, "Kyoto Microcomputer Co., Ltd. KZM-ARM11-01")
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = kzm_map_io,
.init_early = imx31_init_early,
.init_irq = mx31_init_irq,
MACHINE_START(MX1ADS, "Freescale MX1ADS")
/* Maintainer: Sascha Hauer, Pengutronix */
- .boot_params = MX1_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx1_map_io,
.init_early = imx1_init_early,
.init_irq = mx1_init_irq,
MACHINE_END
MACHINE_START(MXLADS, "Freescale MXLADS")
- .boot_params = MX1_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx1_map_io,
.init_early = imx1_init_early,
.init_irq = mx1_init_irq,
MACHINE_START(MX21ADS, "Freescale i.MX21ADS")
/* maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX21_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx21ads_map_io,
.init_early = imx21_init_early,
.init_irq = mx21_init_irq,
MACHINE_START(MX25_3DS, "Freescale MX25PDK (3DS)")
/* Maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX25_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx25_map_io,
.init_early = imx25_init_early,
.init_irq = mx25_init_irq,
MACHINE_START(MX27_3DS, "Freescale MX27PDK")
/* maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
-
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <mach/iomux-mx27.h>
#include "devices-imx27.h"
MACHINE_START(MX27ADS, "Freescale i.MX27ADS")
/* maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27ads_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
/* Maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx31_map_io,
.init_early = imx31_init_early,
.init_irq = mx31_init_irq,
MACHINE_START(MX31ADS, "Freescale MX31ADS")
/* Maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx31ads_map_io,
.init_early = imx31_init_early,
.init_irq = mx31ads_init_irq,
};
MACHINE_START(LILLY1131, "INCO startec LILLY-1131")
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx31_map_io,
.init_early = imx31_init_early,
.init_irq = mx31_init_irq,
MACHINE_START(MX31LITE, "LogicPD i.MX31 SOM")
/* Maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx31lite_map_io,
.init_early = imx31_init_early,
.init_irq = mx31_init_irq,
MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard")
/* Maintainer: Valentin Longchamp, EPFL Mobots group */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.reserve = mx31moboard_reserve,
.map_io = mx31_map_io,
.init_early = imx31_init_early,
MACHINE_START(MX35_3DS, "Freescale MX35PDK")
/* Maintainer: Freescale Semiconductor, Inc */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx35_map_io,
.init_early = imx35_init_early,
.init_irq = mx35_init_irq,
MACHINE_START(MXT_TD60, "Maxtrack i-MXT TD60")
/* maintainer: Maxtrack Industrial */
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
};
MACHINE_START(PCA100, "phyCARD-i.MX27")
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
MACHINE_START(PCM037, "Phytec Phycore pcm037")
/* Maintainer: Pengutronix */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.reserve = pcm037_reserve,
.map_io = mx31_map_io,
.init_early = imx31_init_early,
};
MACHINE_START(PCM038, "phyCORE-i.MX27")
- .boot_params = MX27_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
MACHINE_START(PCM043, "Phytec Phycore pcm043")
/* Maintainer: Pengutronix */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx35_map_io,
.init_early = imx35_init_early,
.init_irq = mx35_init_irq,
MACHINE_START(QONG, "Dave/DENX QongEVB-LITE")
/* Maintainer: DENX Software Engineering GmbH */
- .boot_params = MX3x_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx31_map_io,
.init_early = imx31_init_early,
.init_irq = mx31_init_irq,
MACHINE_START(SCB9328, "Synertronixx scb9328")
/* Sascha Hauer */
- .boot_params = 0x08000100,
+ .atag_offset = 100,
.map_io = mx1_map_io,
.init_early = imx1_init_early,
.init_irq = mx1_init_irq,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
/*
* WARNING: this has to mirror definitions in platform.h
*/
MACHINE_START(INTEGRATOR, "ARM-Integrator")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.reserve = integrator_reserve,
.map_io = ap_map_io,
.init_early = integrator_init_early,
MACHINE_START(CINTEGRATOR, "ARM-IntegratorCP")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.reserve = integrator_reserve,
.map_io = intcp_map_io,
.init_early = intcp_init_early,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
MACHINE_START(IQ81340MC, "Intel IQ81340MC")
/* Maintainer: Dan Williams <dan.j.williams@intel.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = iop13xx_map_io,
.init_irq = iop13xx_init_irq,
.timer = &iq81340mc_timer,
MACHINE_START(IQ81340SC, "Intel IQ81340SC")
/* Maintainer: Dan Williams <dan.j.williams@intel.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = iop13xx_map_io,
.init_irq = iop13xx_init_irq,
.timer = &iq81340sc_timer,
- zreladdr-y := 0xa0008000
+ zreladdr-y += 0xa0008000
params_phys-y := 0xa0000100
initrd_phys-y := 0xa0800000
}
MACHINE_START(EM7210, "Lanner EM7210")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = em7210_map_io,
.init_irq = iop32x_init_irq,
.timer = &em7210_timer,
MACHINE_START(GLANTANK, "GLAN Tank")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = glantank_map_io,
.init_irq = iop32x_init_irq,
.timer = &glantank_timer,
MACHINE_START(IQ31244, "Intel IQ31244")
/* Maintainer: Intel Corp. */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = iq31244_map_io,
.init_irq = iop32x_init_irq,
.timer = &iq31244_timer,
*/
MACHINE_START(EP80219, "Intel EP80219")
/* Maintainer: Intel Corp. */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = iq31244_map_io,
.init_irq = iop32x_init_irq,
.timer = &iq31244_timer,
MACHINE_START(IQ80321, "Intel IQ80321")
/* Maintainer: Intel Corp. */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = iq80321_map_io,
.init_irq = iop32x_init_irq,
.timer = &iq80321_timer,
MACHINE_START(N2100, "Thecus N2100")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = n2100_map_io,
.init_irq = iop32x_init_irq,
.timer = &n2100_timer,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
MACHINE_START(IQ80331, "Intel IQ80331")
/* Maintainer: Intel Corp. */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = iop3xx_map_io,
.init_irq = iop33x_init_irq,
.timer = &iq80331_timer,
MACHINE_START(IQ80332, "Intel IQ80332")
/* Maintainer: Intel Corp. */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = iop3xx_map_io,
.init_irq = iop33x_init_irq,
.timer = &iq80332_timer,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ixp2000.h>
static DEFINE_SPINLOCK(ixp2000_slowport_lock);
static unsigned long ixp2000_slowport_irq_flags;
MACHINE_START(ENP2611, "Radisys ENP-2611 PCI network processor board")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = enp2611_map_io,
.init_irq = ixp2000_init_irq,
.timer = &enp2611_timer,
*
* Copyright (C) 2002 Intel Corporation.
*
- * This program is free software, you can redistribute it and/or modify
+ * This program is free software, you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/*
* IXP2000 GPIO in/out, edge/level detection for IRQs:
* IRQs are generated on Falling-edge, Rising-Edge, Level-low, Level-High
- * or both Falling-edge and Rising-edge.
+ * or both Falling-edge and Rising-edge.
* This must be called *before* the corresponding IRQ is registerd.
* Use this instead of directly setting the GPIO registers.
* GPIOs may also be used as GPIOs (e.g. for emulating i2c/smb)
MACHINE_START(IXDP2400, "Intel IXDP2400 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixdp2x00_map_io,
.init_irq = ixdp2400_init_irq,
.timer = &ixdp2400_timer,
MACHINE_START(IXDP2800, "Intel IXDP2800 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixdp2x00_map_io,
.init_irq = ixdp2800_init_irq,
.timer = &ixdp2800_timer,
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <asm/mach/flash.h>
#include <asm/mach/arch.h>
-#include <mach/gpio.h>
-
+#include <mach/gpio-ixp2000.h>
/*************************************************************************
* IXDP2x00 IRQ Initialization
#ifdef CONFIG_ARCH_IXDP2401
MACHINE_START(IXDP2401, "Intel IXDP2401 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixdp2x01_map_io,
.init_irq = ixdp2x01_init_irq,
.timer = &ixdp2x01_timer,
#ifdef CONFIG_ARCH_IXDP2801
MACHINE_START(IXDP2801, "Intel IXDP2801 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixdp2x01_map_io,
.init_irq = ixdp2x01_init_irq,
.timer = &ixdp2x01_timer,
*/
MACHINE_START(IXDP28X5, "Intel IXDP2805/2855 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixdp2x01_map_io,
.init_irq = ixdp2x01_init_irq,
.timer = &ixdp2x01_timer,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
.map_io = ixp23xx_map_io,
.init_irq = ixp23xx_init_irq,
.timer = &ixp23xx_timer,
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = espresso_init,
MACHINE_END
.map_io = ixdp2351_map_io,
.init_irq = ixdp2351_init_irq,
.timer = &ixp23xx_timer,
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = ixdp2351_init,
MACHINE_END
.map_io = ixp23xx_map_io,
.init_irq = ixp23xx_init_irq,
.timer = &ixp23xx_timer,
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = roadrunner_init,
MACHINE_END
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = avila_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = avila_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
local_write_config(PCI_BASE_ADDRESS_0, 4, PHYS_OFFSET);
local_write_config(PCI_BASE_ADDRESS_1, 4, PHYS_OFFSET + SZ_16M);
local_write_config(PCI_BASE_ADDRESS_2, 4, PHYS_OFFSET + SZ_32M);
- local_write_config(PCI_BASE_ADDRESS_3, 4, PHYS_OFFSET + SZ_48M);
+ local_write_config(PCI_BASE_ADDRESS_3, 4,
+ PHYS_OFFSET + SZ_32M + SZ_16M);
/*
* Enable CSR window at 64 MiB to allow PCI masters
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = coyote_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = coyote_init,
MACHINE_END
#endif
* Author: Rod Whitby <rod@whitby.id.au>
* Maintainers: http://www.nslu2-linux.org/
*/
-
+#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/jiffies.h>
#include <linux/timer.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/time.h>
-#include <asm/gpio.h>
#define DSMG600_SDA_PIN 5
#define DSMG600_SCL_PIN 4
MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
/* Maintainer: www.nslu2-linux.org */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &dsmg600_timer,
* Maintainers: http://www.nslu2-linux.org/
*
*/
-
+#include <linux/gpio.h>
#include <linux/if_ether.h>
#include <linux/irq.h>
#include <linux/serial.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
-#include <asm/gpio.h>
#define FSG_SDA_PIN 12
#define FSG_SCL_PIN 13
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = fsg_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = gateway7001_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = gmlr_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = gtwx5715_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
#include <linux/kernel.h>
#include <mach/hardware.h>
+#define __ARM_GPIOLIB_COMPLEX
+
static inline int gpio_request(unsigned gpio, const char *label)
{
return 0;
#include <asm-generic/gpio.h> /* cansleep wrappers */
extern int gpio_to_irq(int gpio);
+#define gpio_to_irq gpio_to_irq
extern int irq_to_gpio(unsigned int irq);
#endif
#include <mach/hardware.h>
-#define IO_SPACE_LIMIT 0x0000ffff
-
extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
* Maintainers: http://www.nslu2-linux.org/
*
*/
-
+#include <linux/gpio.h>
#include <linux/if_ether.h>
#include <linux/irq.h>
#include <linux/jiffies.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
-#include <asm/gpio.h>
#define NAS100D_SDA_PIN 5
#define NAS100D_SCL_PIN 6
MACHINE_START(NAS100D, "Iomega NAS 100d")
/* Maintainer: www.nslu2-linux.org */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
* Maintainers: http://www.nslu2-linux.org/
*
*/
-
+#include <linux/gpio.h>
#include <linux/if_ether.h>
#include <linux/irq.h>
#include <linux/serial.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/time.h>
-#include <asm/gpio.h>
#define NSLU2_SDA_PIN 7
#define NSLU2_SCL_PIN 6
MACHINE_START(NSLU2, "Linksys NSLU2")
/* Maintainer: www.nslu2-linux.org */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &nslu2_timer,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = vulcan_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
- .boot_params = 0x0100,
+ .atag_offset = 0x100,
.init_machine = wg302v2_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
}
MACHINE_START(D2NET_V2, "LaCie d2 Network v2")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = d2net_v2_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
MACHINE_START(DB88F6281_BP, "Marvell DB-88F6281-BP Development Board")
/* Maintainer: Saeed Bishara <saeed@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = db88f6281_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
}
MACHINE_START(DOCKSTAR, "Seagate FreeAgent DockStar")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = dockstar_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board")
/* Maintainer: Siddarth Gore <gores@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = guruplug_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <mach/bridge-regs.h>
#include <plat/irq.h>
-#include <asm/gpio.h>
#include "common.h"
static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mbus.h>
#include <linux/io.h>
-#include <asm/gpio.h>
#include <mach/hardware.h>
#include <plat/mpp.h>
#include "common.h"
MACHINE_START(MV88F6281GTW_GE, "Marvell 88F6281 GTW GE Board")
/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = mv88f6281gtw_ge_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_NETSPACE_V2
MACHINE_START(NETSPACE_V2, "LaCie Network Space v2")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = netspace_v2_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_INETSPACE_V2
MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = netspace_v2_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_NETSPACE_MAX_V2
MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = netspace_v2_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_NET2BIG_V2
MACHINE_START(NET2BIG_V2, "LaCie 2Big Network v2")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = netxbig_v2_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_NET5BIG_V2
MACHINE_START(NET5BIG_V2, "LaCie 5Big Network v2")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = netxbig_v2_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_OPENRD_BASE
MACHINE_START(OPENRD_BASE, "Marvell OpenRD Base Board")
/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = openrd_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_OPENRD_CLIENT
MACHINE_START(OPENRD_CLIENT, "Marvell OpenRD Client Board")
/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = openrd_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_OPENRD_ULTIMATE
MACHINE_START(OPENRD_ULTIMATE, "Marvell OpenRD Ultimate Board")
/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = openrd_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
MACHINE_START(RD88F6192_NAS, "Marvell RD-88F6192-NAS Development Board")
/* Maintainer: Saeed Bishara <saeed@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = rd88f6192_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
MACHINE_START(RD88F6281, "Marvell RD-88F6281 Reference Board")
/* Maintainer: Saeed Bishara <saeed@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = rd88f6281_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_SHEEVAPLUG
MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
/* Maintainer: shadi Ammouri <shadi@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = sheevaplug_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
#ifdef CONFIG_MACH_ESATA_SHEEVAPLUG
MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = sheevaplug_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
MACHINE_START(T5325, "HP t5325 Thin Client")
/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = hp_t5325_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
MACHINE_START(TS219, "QNAP TS-119/TS-219")
/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = qnap_ts219_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
MACHINE_START(TS41X, "QNAP TS-41x")
/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = qnap_ts41x_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
# Makefile for KS8695 architecture support
#
-obj-y := cpu.o irq.o time.o gpio.o devices.o
+obj-y := cpu.o irq.o time.o devices.o
obj-m :=
obj-n :=
obj- :=
# PARAMS_PHYS must be within 4MB of ZRELADDR
# INITRD_PHYS must be in RAM
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <asm/mach/irq.h>
#include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
#include "generic.h"
MACHINE_START(ACS5K, "Brivo Systems LLC ACS-5000 Master board")
/* Maintainer: Simtec Electronics. */
- .boot_params = KS8695_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = ks8695_map_io,
.init_irq = ks8695_init_irq,
.init_machine = acs5k_init,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <asm/mach/irq.h>
#include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
#include "generic.h"
MACHINE_START(DSM320, "D-Link DSM-320 Wireless Media Player")
/* Maintainer: Simtec Electronics. */
- .boot_params = KS8695_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = ks8695_map_io,
.init_irq = ks8695_init_irq,
.init_machine = dsm320_init,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
#include <mach/devices.h>
#include "generic.h"
MACHINE_START(KS8695, "KS8695 Centaur Development Board")
/* Maintainer: Micrel Semiconductor Inc. */
- .boot_params = KS8695_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = ks8695_map_io,
.init_irq = ks8695_init_irq,
.init_machine = micrel_init,
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <mach/irqs.h>
--- /dev/null
+/*
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_KS8659_GPIO_H
+#define __MACH_KS8659_GPIO_H
+
+#include <linux/kernel.h>
+
+#define KS8695_GPIO_0 0
+#define KS8695_GPIO_1 1
+#define KS8695_GPIO_2 2
+#define KS8695_GPIO_3 3
+#define KS8695_GPIO_4 4
+#define KS8695_GPIO_5 5
+#define KS8695_GPIO_6 6
+#define KS8695_GPIO_7 7
+#define KS8695_GPIO_8 8
+#define KS8695_GPIO_9 9
+#define KS8695_GPIO_10 10
+#define KS8695_GPIO_11 11
+#define KS8695_GPIO_12 12
+#define KS8695_GPIO_13 13
+#define KS8695_GPIO_14 14
+#define KS8695_GPIO_15 15
+
+/*
+ * Configure GPIO pin as external interrupt source.
+ */
+extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
+
+/* Register the GPIOs */
+extern void ks8695_register_gpios(void);
+
+#endif /* __MACH_KS8659_GPIO_H */
#ifndef __ASM_ARCH_GPIO_H_
#define __ASM_ARCH_GPIO_H_
-#include <linux/kernel.h>
-
-#define KS8695_GPIO_0 0
-#define KS8695_GPIO_1 1
-#define KS8695_GPIO_2 2
-#define KS8695_GPIO_3 3
-#define KS8695_GPIO_4 4
-#define KS8695_GPIO_5 5
-#define KS8695_GPIO_6 6
-#define KS8695_GPIO_7 7
-#define KS8695_GPIO_8 8
-#define KS8695_GPIO_9 9
-#define KS8695_GPIO_10 10
-#define KS8695_GPIO_11 11
-#define KS8695_GPIO_12 12
-#define KS8695_GPIO_13 13
-#define KS8695_GPIO_14 14
-#define KS8695_GPIO_15 15
-
-/*
- * Configure GPIO pin as external interrupt source.
- */
-extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
-
/*
* Map IRQ number to GPIO line.
*/
extern int irq_to_gpio(unsigned int irq);
-#include <asm-generic/gpio.h>
-
-/* If it turns out that we need to optimise GPIO access for the
- * Micrel's GPIOs, then these can be changed to check their argument
- * directly as static inlines. However for now it's probably not
- * worthwhile.
- */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_to_irq __gpio_to_irq
-
-/* Register the GPIOs */
-extern void ks8695_register_gpios(void);
-
#endif
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
+#include <linux/gpio.h>
#include <asm/leds.h>
#include <mach/devices.h>
-#include <mach/gpio.h>
static inline void ks8695_led_on(unsigned int led)
#
obj-y := timer.o irq.o common.o serial.o clock.o
-obj-y += gpiolib.o pm.o suspend.o
+obj-y += pm.o suspend.o
obj-y += phy3250.o
- zreladdr-y := 0x80008000
+ zreladdr-y += 0x80008000
params_phys-y := 0x80000100
initrd_phys-y := 0x82000000
--- /dev/null
+/*
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MACH_GPIO_LPC32XX_H
+#define __MACH_GPIO_LPC32XX_H
+
+/*
+ * Note!
+ * Muxed GP pins need to be setup to the GP state in the board level
+ * code prior to using this driver.
+ * GPI pins : 28xP3 group
+ * GPO pins : 24xP3 group
+ * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
+ */
+
+#define LPC32XX_GPIO_P0_MAX 8
+#define LPC32XX_GPIO_P1_MAX 24
+#define LPC32XX_GPIO_P2_MAX 13
+#define LPC32XX_GPIO_P3_MAX 6
+#define LPC32XX_GPI_P3_MAX 28
+#define LPC32XX_GPO_P3_MAX 24
+
+#define LPC32XX_GPIO_P0_GRP 0
+#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
+#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
+#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
+#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
+#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
+
+/*
+ * A specific GPIO can be selected with this macro
+ * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+ * See the LPC32x0 User's guide for GPIO group numbers
+ */
+#define LPC32XX_GPIO(x, y) ((x) + (y))
+
+#endif /* __MACH_GPIO_LPC32XX_H */
-/*
- * arch/arm/mach-lpc32xx/include/mach/gpio.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-/*
- * Note!
- * Muxed GP pins need to be setup to the GP state in the board level
- * code prior to using this driver.
- * GPI pins : 28xP3 group
- * GPO pins : 24xP3 group
- * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
- */
-
-#define LPC32XX_GPIO_P0_MAX 8
-#define LPC32XX_GPIO_P1_MAX 24
-#define LPC32XX_GPIO_P2_MAX 13
-#define LPC32XX_GPIO_P3_MAX 6
-#define LPC32XX_GPI_P3_MAX 28
-#define LPC32XX_GPO_P3_MAX 24
-
-#define LPC32XX_GPIO_P0_GRP 0
-#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
-#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
-#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
-#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
-#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
-
-/*
- * A specific GPIO can be selected with this macro
- * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
- * See the LPC32x0 User's guide for GPIO group numbers
- */
-#define LPC32XX_GPIO(x, y) ((x) + (y))
-
-static inline int gpio_get_value(unsigned gpio)
-{
- return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- __gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
- return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
- return __gpio_to_irq(gpio);
-}
-
-#endif
#include <mach/hardware.h>
#include <mach/platform.h>
+#include <mach/gpio-lpc32xx.h>
#include "common.h"
/*
MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller")
/* Maintainer: Kevin Wells, NXP Semiconductors */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = lpc32xx_map_io,
.init_irq = lpc32xx_init_irq,
.timer = &lpc32xx_timer,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
* it under the terms of the GNU General Public License version 2 as
* publishhed by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <mach/addr-map.h>
#include <mach/mfp-pxa168.h>
#include <mach/pxa168.h>
-#include <mach/gpio.h>
#include <video/pxa168fb.h>
#include <linux/input.h>
#include <plat/pxa27x_keypad.h>
}, {
.name = "filesystem",
.offset = MTDPART_OFS_APPEND,
- .size = SZ_48M,
+ .size = SZ_32M + SZ_16M,
.mask_flags = 0,
}
};
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/irqs.h>
#include <mach/dma.h>
#include <mach/mfp.h>
-#include <mach/gpio.h>
#include <mach/devices.h>
#include <mach/mmp2.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/regs-apbc.h>
#include <mach/regs-apmu.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/dma.h>
#include <mach/devices.h>
#include <mach/mfp.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/regs-apmu.h>
#include <mach/cputype.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/dma.h>
#include <mach/mfp.h>
#include <mach/devices.h>
* it under the terms of the GNU General Public License version 2 as
* publishhed by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <mach/addr-map.h>
#include <mach/mfp-pxa910.h>
#include <mach/pxa910.h>
-#include <mach/gpio.h>
#include "common.h"
}, {
.name = "filesystem",
.offset = MTDPART_OFS_APPEND,
- .size = SZ_48M,
+ .size = SZ_32M + SZ_16M,
.mask_flags = 0,
}
};
- zreladdr-y := 0x10008000
+ zreladdr-y += 0x10008000
params_phys-y := 0x10000100
initrd_phys-y := 0x10800000
}
MACHINE_START(HALIBUT, "Halibut Board (QCT SURF7200A)")
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.fixup = halibut_fixup,
.map_io = halibut_map_io,
.init_irq = halibut_init_irq,
extern struct sys_timer msm_timer;
MACHINE_START(MAHIMAHI, "mahimahi")
- .boot_params = 0x20000100,
+ .atag_offset = 0x100,
.fixup = mahimahi_fixup,
.map_io = mahimahi_map_io,
.init_irq = msm_init_irq,
* GNU General Public License for more details.
*
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <mach/vreg.h>
#include <mach/mpp.h>
-#include <mach/gpio.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
}
MACHINE_START(MSM7X27_SURF, "QCT MSM7x27 SURF")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = msm7x2x_map_io,
.init_irq = msm7x2x_init_irq,
.init_machine = msm7x2x_init,
MACHINE_END
MACHINE_START(MSM7X27_FFA, "QCT MSM7x27 FFA")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = msm7x2x_map_io,
.init_irq = msm7x2x_init_irq,
.init_machine = msm7x2x_init,
MACHINE_END
MACHINE_START(MSM7X25_SURF, "QCT MSM7x25 SURF")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = msm7x2x_map_io,
.init_irq = msm7x2x_init_irq,
.init_machine = msm7x2x_init,
MACHINE_END
MACHINE_START(MSM7X25_FFA, "QCT MSM7x25 FFA")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = msm7x2x_map_io,
.init_irq = msm7x2x_init_irq,
.init_machine = msm7x2x_init,
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
* 02110-1301, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <linux/smsc911x.h>
#include <linux/usb/msm_hsusb.h>
#include <linux/clkdev.h>
+#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/memory.h>
#include <asm/setup.h>
-#include <mach/gpio.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
#include <mach/dma.h>
extern struct sys_timer msm_timer;
+static void __init msm7x30_fixup(struct machine_desc *desc, struct tag *tag,
+ char **cmdline, struct meminfo *mi)
+{
+ for (; tag->hdr.size; tag = tag_next(tag))
+ if (tag->hdr.tag == ATAG_MEM && tag->u.mem.start == 0x200000) {
+ tag->u.mem.start = 0;
+ tag->u.mem.size += SZ_2M;
+ }
+}
+
+static void __init msm7x30_reserve(void)
+{
+ memblock_remove(0x0, SZ_2M);
+}
+
static int hsusb_phy_init_seq[] = {
0x30, 0x32, /* Enable and set Pre-Emphasis Depth to 20% */
0x02, 0x36, /* Disable CDR Auto Reset feature */
}
MACHINE_START(MSM7X30_SURF, "QCT MSM7X30 SURF")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
+ .fixup = msm7x30_fixup,
+ .reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
MACHINE_END
MACHINE_START(MSM7X30_FFA, "QCT MSM7X30 FFA")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
+ .fixup = msm7x30_fixup,
+ .reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
MACHINE_END
MACHINE_START(MSM7X30_FLUID, "QCT MSM7X30 FLUID")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
+ .fixup = msm7x30_fixup,
+ .reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/clkdev.h>
+#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
+#include <asm/setup.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
#include "devices.h"
+static void __init msm8960_fixup(struct machine_desc *desc, struct tag *tag,
+ char **cmdline, struct meminfo *mi)
+{
+ for (; tag->hdr.size; tag = tag_next(tag))
+ if (tag->hdr.tag == ATAG_MEM &&
+ tag->u.mem.start == 0x40200000) {
+ tag->u.mem.start = 0x40000000;
+ tag->u.mem.size += SZ_2M;
+ }
+}
+
+static void __init msm8960_reserve(void)
+{
+ memblock_remove(0x40000000, SZ_2M);
+}
+
static void __init msm8960_map_io(void)
{
msm_map_msm8960_io();
}
MACHINE_START(MSM8960_SIM, "QCT MSM8960 SIMULATOR")
+ .fixup = msm8960_fixup,
+ .reserve = msm8960_reserve,
.map_io = msm8960_map_io,
.init_irq = msm8960_init_irq,
.timer = &msm_timer,
MACHINE_END
MACHINE_START(MSM8960_RUMI3, "QCT MSM8960 RUMI3")
+ .fixup = msm8960_fixup,
+ .reserve = msm8960_reserve,
.map_io = msm8960_map_io,
.init_irq = msm8960_init_irq,
.timer = &msm_timer,
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
+#include <asm/setup.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
+static void __init msm8x60_fixup(struct machine_desc *desc, struct tag *tag,
+ char **cmdline, struct meminfo *mi)
+{
+ for (; tag->hdr.size; tag = tag_next(tag))
+ if (tag->hdr.tag == ATAG_MEM &&
+ tag->u.mem.start == 0x40200000) {
+ tag->u.mem.start = 0x40000000;
+ tag->u.mem.size += SZ_2M;
+ }
+}
+
+static void __init msm8x60_reserve(void)
+{
+ memblock_remove(0x40000000, SZ_2M);
+}
static void __init msm8x60_map_io(void)
{
}
MACHINE_START(MSM8X60_RUMI3, "QCT MSM8X60 RUMI3")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
MACHINE_END
MACHINE_START(MSM8X60_SURF, "QCT MSM8X60 SURF")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
MACHINE_END
MACHINE_START(MSM8X60_SIM, "QCT MSM8X60 SIMULATOR")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
MACHINE_END
MACHINE_START(MSM8X60_FFA, "QCT MSM8X60 FFA")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
* 02110-1301, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <mach/board.h>
#include <mach/irqs.h>
#include <mach/sirc.h>
-#include <mach/gpio.h>
#include <mach/vreg.h>
#include <mach/mmc.h>
}
MACHINE_START(QSD8X50_SURF, "QCT QSD8X50 SURF")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = qsd8x50_map_io,
.init_irq = qsd8x50_init_irq,
.init_machine = qsd8x50_init,
MACHINE_END
MACHINE_START(QSD8X50A_ST1_5, "QCT QSD8X50A ST1.5")
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = qsd8x50_map_io,
.init_irq = qsd8x50_init_irq,
.init_machine = qsd8x50_init,
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
-#include <asm/gpio.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
MACHINE_START(SAPPHIRE, "sapphire")
/* Maintainer: Brian Swetland <swetland@google.com> */
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.fixup = sapphire_fixup,
.map_io = sapphire_map_io,
.init_irq = sapphire_init_irq,
/* linux/arch/arm/mach-msm/board-trout-mmc.c
** Author: Brian Swetland <swetland@google.com>
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/err.h>
#include <linux/debugfs.h>
-#include <asm/gpio.h>
#include <asm/io.h>
#include <mach/vreg.h>
/* linux/arch/arm/mach-msm/board-trout-mddi.c
** Author: Brian Swetland <swetland@google.com>
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/err.h>
#include <asm/io.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <mach/msm_fb.h>
}
MACHINE_START(TROUT, "HTC Dream")
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.fixup = trout_fixup,
.map_io = trout_map_io,
.init_irq = trout_init_irq,
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved.
- * Author: Mike Lockwood <lockwood@android.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-#ifndef __ASM_ARCH_MSM_GPIO_H
-#define __ASM_ARCH_MSM_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
-#endif /* __ASM_ARCH_MSM_GPIO_H */
+/* empty */
#elif defined(CONFIG_ARCH_QSD8X50)
#define PLAT_PHYS_OFFSET UL(0x20000000)
#elif defined(CONFIG_ARCH_MSM7X30)
-#define PLAT_PHYS_OFFSET UL(0x00200000)
+#define PLAT_PHYS_OFFSET UL(0x00000000)
#elif defined(CONFIG_ARCH_MSM8X60)
-#define PLAT_PHYS_OFFSET UL(0x40200000)
+#define PLAT_PHYS_OFFSET UL(0x40000000)
#elif defined(CONFIG_ARCH_MSM8960)
-#define PLAT_PHYS_OFFSET UL(0x40200000)
+#define PLAT_PHYS_OFFSET UL(0x40000000)
#else
#define PLAT_PHYS_OFFSET UL(0x10000000)
#endif
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
MACHINE_START(TERASTATION_WXL, "Buffalo Nas WXL")
/* Maintainer: Sebastien Requiem <sebastien@requiem.fr> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = wxl_init,
.map_io = mv78xx0_map_io,
.init_early = mv78xx0_init_early,
MACHINE_START(DB78X00_BP, "Marvell DB-78x00-BP Development Board")
/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = db78x00_init,
.map_io = mv78xx0_map_io,
.init_early = mv78xx0_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/irq.h>
-#include <asm/gpio.h>
#include <mach/bridge-regs.h>
#include <plat/irq.h>
#include "common.h"
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mbus.h>
#include <linux/io.h>
#include <plat/mpp.h>
-#include <asm/gpio.h>
#include <mach/hardware.h>
#include "common.h"
#include "mpp.h"
MACHINE_START(RD78X00_MASA, "Marvell RD-78x00-MASA Development Board")
/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = rd78x00_masa_init,
.map_io = mv78xx0_map_io,
.init_early = mv78xx0_init_early,
- zreladdr-$(CONFIG_ARCH_MX50) := 0x70008000
+ zreladdr-$(CONFIG_ARCH_MX50) += 0x70008000
params_phys-$(CONFIG_ARCH_MX50) := 0x70000100
initrd_phys-$(CONFIG_ARCH_MX50) := 0x70800000
- zreladdr-$(CONFIG_ARCH_MX51) := 0x90008000
+ zreladdr-$(CONFIG_ARCH_MX51) += 0x90008000
params_phys-$(CONFIG_ARCH_MX51) := 0x90000100
initrd_phys-$(CONFIG_ARCH_MX51) := 0x90800000
- zreladdr-$(CONFIG_ARCH_MX53) := 0x70008000
+ zreladdr-$(CONFIG_ARCH_MX53) += 0x70008000
params_phys-$(CONFIG_ARCH_MX53) := 0x70000100
initrd_phys-$(CONFIG_ARCH_MX53) := 0x70800000
MACHINE_START(EUKREA_CPUIMX51, "Eukrea CPUIMX51 Module")
/* Maintainer: Eric Bénard <eric@eukrea.com> */
- .boot_params = MX51_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
/* Maintainer: Eric Bénard <eric@eukrea.com> */
- .boot_params = MX51_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
MACHINE_START(MX51_3DS, "Freescale MX51 3-Stack Board")
/* Maintainer: Freescale Semiconductor, Inc. */
- .boot_params = MX51_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
MACHINE_START(MX51_BABBAGE, "Freescale MX51 Babbage Board")
/* Maintainer: Amit Kucheria <amit.kucheria@canonical.com> */
- .boot_params = MX51_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
MACHINE_START(MX51_EFIKAMX, "Genesi EfikaMX nettop")
/* Maintainer: Amit Kucheria <amit.kucheria@linaro.org> */
- .boot_params = MX51_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
};
MACHINE_START(MX51_EFIKASB, "Genesi Efika Smartbook")
- .boot_params = MX51_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
-zreladdr-y := 0x40008000
+zreladdr-y += 0x40008000
#ifndef __MACH_MXS_GPIO_H__
#define __MACH_MXS_GPIO_H__
-#include <asm-generic/gpio.h>
-
#define MXS_GPIO_NR(bank, nr) ((bank) * 32 + (nr))
-/* use gpiolib dispatchers */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
#define irq_to_gpio(irq) ((irq) - MXS_GPIO_IRQ_START)
#endif /* __MACH_MXS_GPIO_H__ */
- zreladdr-y := 0x80008000
+ zreladdr-y += 0x80008000
}
MACHINE_START(NXDB500, "Hilscher nxdb500")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = netx_map_io,
.init_irq = netx_init_irq,
.timer = &netx_timer,
}
MACHINE_START(NXDKN, "Hilscher nxdkn")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = netx_map_io,
.init_irq = netx_init_irq,
.timer = &netx_timer,
}
MACHINE_START(NXEB500HMI, "Hilscher nxeb500hmi")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = netx_map_io,
.init_irq = netx_init_irq,
.timer = &netx_timer,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
+#include <plat/gpio-nomadik.h>
#include <plat/mtu.h>
#include <mach/setup.h>
MACHINE_START(NOMADIK, "NHK8815")
/* Maintainer: ST MicroElectronics */
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = cpu8815_map_io,
.init_irq = cpu8815_init_irq,
.timer = &nomadik_timer,
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
#include <asm/mach/map.h>
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
#include <linux/i2c-gpio.h>
-#include <linux/gpio.h>
#include <linux/platform_device.h>
+#include <plat/gpio-nomadik.h>
/*
* There are two busses in the 8815NHK.
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H
-#include <plat/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
-zreladdr-y := 0x00008000
+zreladdr-y += 0x00008000
params_phys-y := 0x00000100
MACHINE_START(NUC932EVB, "NUC932EVB")
/* Maintainer: Wan ZongShun */
- .boot_params = 0,
.map_io = nuc932evb_map_io,
.init_irq = nuc93x_init_irq,
.init_machine = nuc932evb_init,
- zreladdr-y := 0x10008000
+ zreladdr-y += 0x10008000
params_phys-y := 0x10000100
initrd_phys-y := 0x10800000
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <plat/io.h>
#include <plat/board-ams-delta.h>
-#include <mach/gpio.h>
#include <plat/keypad.h>
#include <plat/mux.h>
#include <plat/usb.h>
MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)")
/* Maintainer: Jonathan McDowell <noodles@earth.li> */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = ams_delta_map_io,
.reserve = omap_reserve,
.init_irq = ams_delta_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/tc.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/flash.h>
#include <plat/fpga.h>
MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")
/* Maintainer: Brian Swetland <swetland@google.com> */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_fsample_map_io,
.reserve = omap_reserve,
.init_irq = omap_fsample_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710")
/* Maintainer: Tony Lindgren <tony@atomide.com> */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_generic_map_io,
.reserve = omap_reserve,
.init_irq = omap_generic_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
#include "board-h2.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/smc91x.h>
#include <mach/hardware.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
MACHINE_START(OMAP_H2, "TI-H2")
/* Maintainer: Imre Deak <imre.deak@nokia.com> */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = h2_map_io,
.reserve = omap_reserve,
.init_irq = h2_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
#include "board-h3.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/major.h>
#include <asm/setup.h>
#include <asm/page.h>
#include <mach/hardware.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
/* Maintainer: Texas Instruments, Inc. */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = h3_map_io,
.reserve = omap_reserve,
.init_irq = h3_init_irq,
* 02110-1301, USA.
*
*/
-
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
MACHINE_START(HERALD, "HTC Herald")
/* Maintainer: Cory Maccarrone <darkstar6262@gmail.com> */
/* Maintainer: wing-linux.sourceforge.net */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = htcherald_map_io,
.reserve = omap_reserve,
.init_irq = htcherald_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <plat/mux.h>
#include <plat/flash.h>
#include <plat/fpga.h>
-#include <mach/gpio.h>
#include <plat/tc.h>
#include <plat/usb.h>
#include <plat/keypad.h>
MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
/* Maintainer: MontaVista Software, Inc. */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = innovator_map_io,
.reserve = omap_reserve,
.init_irq = innovator_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mutex.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
}
MACHINE_START(NOKIA770, "Nokia 770")
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_nokia770_map_io,
.reserve = omap_reserve,
.init_irq = omap_nokia770_init_irq,
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
#include <mach/hardware.h>
-#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
MACHINE_START(OMAP_OSK, "TI-OSK")
/* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = osk_map_io,
.reserve = omap_reserve,
.init_irq = osk_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/usb.h>
}
MACHINE_START(OMAP_PALMTE, "OMAP310 based Palm Tungsten E")
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_palmte_map_io,
.reserve = omap_reserve,
.init_irq = omap_palmte_init_irq,
*/
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/led.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/usb.h>
}
MACHINE_START(OMAP_PALMTT, "OMAP1510 based Palm Tungsten|T")
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_palmtt_map_io,
.reserve = omap_reserve,
.init_irq = omap_palmtt_init_irq,
*/
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/usb.h>
}
MACHINE_START(OMAP_PALMZ71, "OMAP310 based Palm Zire71")
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_palmz71_map_io,
.reserve = omap_reserve,
.init_irq = omap_palmz71_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/tc.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/fpga.h>
#include <plat/flash.h>
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
/* Maintainer: Kevin Hilman <kjh@hilman.org> */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_perseus2_map_io,
.reserve = omap_reserve,
.init_irq = omap_perseus2_init_irq,
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
#include <plat/board-sx1.h>
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/dma.h>
}
MACHINE_START(SX1, "OMAP310 based Siemens SX1")
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = omap_sx1_map_io,
.reserve = omap_reserve,
.init_irq = omap_sx1_init_irq,
*/
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <plat/board-voiceblue.h>
#include <plat/common.h>
-#include <mach/gpio.h>
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/tc.h>
MACHINE_START(VOICEBLUE, "VoiceBlue OMAP5910")
/* Maintainer: Ladislav Michl <michl@2n.cz> */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.map_io = voiceblue_map_io,
.reserve = omap_reserve,
.init_irq = voiceblue_init_irq,
*/
#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mux.h>
-#include <mach/gpio.h>
#include <plat/mmc.h>
#include <plat/omap7xx.h>
#include <plat/mcbsp.h>
*/
#include <linux/types.h>
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <asm/mach/irq.h>
#include <plat/fpga.h>
-#include <mach/gpio.h>
static void fpga_mask_irq(struct irq_data *d)
{
#endif
omap_sram_init();
+ omap_init_consistent_dma_size();
}
/*
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/sched.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
#include <plat/cpu.h>
#define IRQ_BANK(irq) ((irq) >> 5)
* The "surfer" expansion board and H2 sample board also have two-color
* green+red LEDs (in parallel), used here for timer and idle indicators.
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel_stat.h>
#include <linux/sched.h>
#include <asm/mach-types.h>
#include <plat/fpga.h>
-#include <mach/gpio.h>
#include "leds.h"
*
* LED driver for OSK with optional Mistral QVGA board
*/
+#include <linux/gpio.h>
#include <linux/init.h>
#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <mach/gpio.h>
-
#include "leds.h"
*
* OMAP LEDs dispatcher
*/
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/leds.h>
#include <asm/mach-types.h>
-#include <mach/gpio.h>
#include <plat/mux.h>
#include "leds.h"
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <plat/board.h>
#include <plat/mux.h>
-#include <mach/gpio.h>
#include <plat/fpga.h>
#include "pm.h"
- zreladdr-y := 0x80008000
+ zreladdr-y += 0x80008000
params_phys-y := 0x80000100
initrd_phys-y := 0x80800000
MACHINE_START(OMAP_2430SDP, "OMAP2430 sdp2430 board")
/* Maintainer: Syed Khasim - Texas Instruments Inc */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap_2430sdp_map_io,
.init_early = omap_2430sdp_init_early,
MACHINE_START(OMAP_3430SDP, "OMAP3430 3430SDP board")
/* Maintainer: Syed Khasim - Texas Instruments Inc */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap_3430sdp_init_early,
}
MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap_sdp_init_early,
MACHINE_START(OMAP_4430SDP, "OMAP4430 4430SDP board")
/* Maintainer: Santosh Shilimkar - Texas Instruments Inc */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap_4430sdp_map_io,
.init_early = omap_4430sdp_init_early,
}
MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = am3517_crane_init_early,
}
MACHINE_START(OMAP3517EVM, "OMAP3517/AM3517 EVM")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = am3517_evm_init_early,
MACHINE_START(OMAP_APOLLON, "OMAP24xx Apollon")
/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap_apollon_map_io,
.init_early = omap_apollon_init_early,
}
MACHINE_START(CM_T35, "Compulab CM-T35")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = cm_t35_init_early,
MACHINE_END
MACHINE_START(CM_T3730, "Compulab CM-T3730")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = cm_t35_init_early,
}
MACHINE_START(CM_T3517, "Compulab CM-T3517")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = cm_t3517_init_early,
}
MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = devkit8000_init_early,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/common.h>
/* XXX This machine entry name should be updated */
MACHINE_START(OMAP_GENERIC, "Generic OMAP24xx")
/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap_generic_map_io,
.init_early = omap_generic_init_early,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/gpio.h>
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/common.h>
MACHINE_START(OMAP_H4, "OMAP2420 H4 board")
/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap_h4_map_io,
.init_early = omap_h4_init_early,
}
MACHINE_START(IGEP0020, "IGEP v2 board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = igep_init_early,
MACHINE_END
MACHINE_START(IGEP0030, "IGEP OMAP3 module")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = igep_init_early,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <plat/mcspi.h>
-#include <mach/gpio.h>
#include <plat/board.h>
#include <plat/common.h>
#include <plat/gpmc.h>
}
MACHINE_START(OMAP_LDP, "OMAP LDP board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap_ldp_init_early,
}
MACHINE_START(NOKIA_N800, "Nokia N800")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = n8x0_map_io,
.init_early = n8x0_init_early,
MACHINE_END
MACHINE_START(NOKIA_N810, "Nokia N810")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = n8x0_map_io,
.init_early = n8x0_init_early,
MACHINE_END
MACHINE_START(NOKIA_N810_WIMAX, "Nokia N810 WiMAX")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = n8x0_map_io,
.init_early = n8x0_init_early,
MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3_beagle_init_early,
MACHINE_START(OMAP3EVM, "OMAP3 EVM")
/* Maintainer: Syed Mohammed Khasim - Texas Instruments */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3_evm_init_early,
}
MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = omap3_map_io,
.init_early = omap3logic_init_early,
.init_irq = omap3_init_irq,
MACHINE_END
MACHINE_START(OMAP3530_LV_SOM, "OMAP Logic 3530 LV SOM board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = omap3_map_io,
.init_early = omap3logic_init_early,
.init_irq = omap3_init_irq,
}
MACHINE_START(OMAP3_PANDORA, "Pandora Handheld Console")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3pandora_init_early,
MACHINE_START(SBC3530, "OMAP3 STALKER")
/* Maintainer: Jason Lam -lzg@ema-tech.com */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = omap3_map_io,
.init_early = omap3_stalker_init_early,
.init_irq = omap3_stalker_init_irq,
MACHINE_START(TOUCHBOOK, "OMAP3 touchbook Board")
/* Maintainer: Gregoire Gentil - http://www.alwaysinnovating.com */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3_touchbook_init_early,
MACHINE_START(OMAP4_PANDA, "OMAP4 Panda board")
/* Maintainer: David Anders - Texas Instruments Inc */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap4_panda_map_io,
.init_early = omap4_panda_init_early,
}
MACHINE_START(OVERO, "Gumstix Overo")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = overo_init_early,
}
MACHINE_START(NOKIA_RM680, "Nokia RM-680 board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = rm680_map_io,
.init_early = rm680_init_early,
MACHINE_START(NOKIA_RX51, "Nokia RX-51 board")
/* Maintainer: Lauri Leukkunen <lauri.leukkunen@nokia.com> */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = rx51_reserve,
.map_io = rx51_map_io,
.init_early = rx51_init_early,
MACHINE_START(TI8168EVM, "ti8168evm")
/* Maintainer: Texas Instruments */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = ti8168_evm_map_io,
.init_early = ti8168_init_early,
.init_irq = ti816x_init_irq,
}
MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap_zoom_init_early,
MACHINE_END
MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board")
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap_zoom_init_early,
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mcbsp.h>
-#include <mach/gpio.h>
#include <plat/mmc.h>
#include <plat/dma.h>
#include <plat/omap_hwmod.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
omap2_check_revision();
omap_sram_init();
+ omap_init_consistent_dma_size();
}
#ifdef CONFIG_SOC_OMAP2420
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
#ifdef CONFIG_MACH_D2NET
MACHINE_START(D2NET, "LaCie d2 Network")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = d2net_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
#ifdef CONFIG_MACH_BIGDISK
MACHINE_START(BIGDISK, "LaCie Big Disk Network")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = d2net_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mv643xx_eth.h>
#include <linux/i2c.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
MACHINE_START(DB88F5281, "Marvell Orion-2 Development Board")
/* Maintainer: Tzachi Perelstein <tzachi@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = db88f5281_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License, or (at your option) any later version.
*
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/phy.h>
#include <linux/marvell_phy.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
/* Warning: D-Link uses a wrong mach-type (=526) in their bootloader */
MACHINE_START(DNS323, "D-Link DNS-323")
/* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = dns323_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
MACHINE_START(EDMINI_V2, "LaCie Ethernet Disk mini V2")
/* Maintainer: Christopher Moore <moore@free.fr> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = edmini_v2_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/io.h>
-#include <asm/gpio.h>
#include <mach/bridge-regs.h>
#include <plat/irq.h>
#include "common.h"
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#ifdef CONFIG_MACH_KUROBOX_PRO
MACHINE_START(KUROBOX_PRO, "Buffalo/Revogear Kurobox Pro")
/* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = kurobox_pro_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
#ifdef CONFIG_MACH_LINKSTATION_PRO
MACHINE_START(LINKSTATION_PRO, "Buffalo Linkstation Pro/Live")
/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = kurobox_pro_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
MACHINE_START(LINKSTATION_LSCHL, "Buffalo Linkstation LiveV3 (LS-CHL)")
/* Maintainer: Ash Hughes <ashley.hughes@blueyonder.co.uk> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = lschl_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
MACHINE_START(LINKSTATION_LS_HGL, "Buffalo Linkstation LS-HGL")
/* Maintainer: Zhu Qingsen <zhuqs@cn.fujistu.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = ls_hgl_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
#ifdef CONFIG_MACH_LINKSTATION_MINI
MACHINE_START(LINKSTATION_MINI, "Buffalo Linkstation Mini")
/* Maintainer: Alexey Kopytko <alexey@kopytko.ru> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = lsmini_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
MACHINE_START(MSS2, "Maxtor Shared Storage II")
/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = mss2_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <mach/orion5x.h>
#include "common.h"
/* Warning: HP uses a wrong mach-type (=526) in their bootloader */
MACHINE_START(MV2120, "HP Media Vault mv2120")
/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = mv2120_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
MACHINE_START(NET2BIG, "LaCie 2Big Network")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = net2big_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ethtool.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
MACHINE_START(RD88F5181L_FXO, "Marvell Orion-VoIP FXO Reference Design")
/* Maintainer: Nicolas Pitre <nico@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = rd88f5181l_fxo_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
MACHINE_START(RD88F5181L_GE, "Marvell Orion-VoIP GE Reference Design")
/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = rd88f5181l_ge_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/i2c.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
MACHINE_START(RD88F5182, "Marvell Orion-NAS Reference Design")
/* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = rd88f5182_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ethtool.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
MACHINE_START(RD88F6183AP_GE, "Marvell Orion-1-90 AP GE Reference Design")
/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = rd88f6183ap_ge_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
MACHINE_START(TERASTATION_PRO2, "Buffalo Terastation Pro II/Live")
/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = tsp2_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
MACHINE_START(TS209, "QNAP TS-109/TS-209")
/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = qnap_ts209_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
MACHINE_START(TS409, "QNAP TS-409")
/* Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = qnap_ts409_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
MACHINE_START(TS78XX, "Technologic Systems TS-78xx SBC")
/* Maintainer: Alexander Clouter <alex@digriz.org.uk> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = ts78xx_init,
.map_io = ts78xx_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/ethtool.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
MACHINE_START(WNR854T, "Netgear WNR854T")
/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = wnr854t_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <net/dsa.h>
#include <asm/mach-types.h>
-#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
MACHINE_START(WRT350N_V2, "Linksys WRT350N v2")
/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_machine = wrt350n_v2_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
- zreladdr-y := 0x80008000
+ zreladdr-y += 0x80008000
params_phys-y := 0x80000100
initrd_phys-y := 0x80800000
MACHINE_START(PNX4008, "Philips PNX4008")
/* Maintainer: MontaVista Software Inc. */
- .boot_params = 0x80000100,
+ .atag_offset = 0x100,
.map_io = pnx4008_map_io,
.init_irq = pnx4008_init_irq,
.init_machine = pnx4008_init,
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <mach/platform.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pnx4008.h>
/* register definitions */
#define PIO_VA_BASE IO_ADDRESS(PNX4008_PIO_BASE)
/*
- * arch/arm/mach-pnx4008/include/mach/gpio.h
+ * arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h
*
* PNX4008 GPIO driver - header file
*
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/io.h>
#include <linux/serial_core.h>
#include <linux/serial_reg.h>
-#include <mach/gpio.h>
+#include <mach/gpio-pnx4008.h>
#include <mach/clock.h>
#define UART_3 0
-zreladdr-y := 0x00008000
+zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
MACHINE_START(PRIMA2_EVB, "prima2cb")
/* Maintainer: Barry Song <baohua.song@csr.com> */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.init_early = sirfsoc_of_clk_init,
.map_io = sirfsoc_map_lluart,
.init_irq = sirfsoc_of_irq_init,
- zreladdr-y := 0xa0008000
+ zreladdr-y += 0xa0008000
.handle_irq = pxa27x_handle_irq,
.timer = &pxa_timer,
.init_machine = balloon3_init,
- .boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .atag_offset = 0x100,
MACHINE_END
MACHINE_START(CAPC7117,
"Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
.handle_irq = pxa3xx_handle_irq,
#endif
MACHINE_START(ARMCORE, "Compulab CM-X2XX")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = cmx2xx_map_io,
.nr_irqs = CMX2XX_NR_IRQS,
.init_irq = cmx2xx_init_irq,
}
MACHINE_START(CM_X300, "CM-X300 module")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
.handle_irq = pxa3xx_handle_irq,
}
MACHINE_START(COLIBRI, "Toradex Colibri PXA270")
- .boot_params = COLIBRI_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = colibri_pxa270_init,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
MACHINE_END
MACHINE_START(INCOME, "Income s.r.o. SH-Dmaster PXA270 SBC")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.init_machine = colibri_pxa270_income_init,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(COLIBRI300, "Toradex Colibri PXA300")
- .boot_params = COLIBRI_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = colibri_pxa300_init,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
}
MACHINE_START(COLIBRI320, "Toradex Colibri PXA320")
- .boot_params = COLIBRI_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = colibri_pxa320_init,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
}
MACHINE_START(CSB726, "Cogent CSB726")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
}
MACHINE_START(EM_X270, "Compulab EM-X270")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
MACHINE_END
MACHINE_START(EXEDA, "Compulab eXeda")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
MACHINE_START(E330, "Toshiba e330")
/* Maintainer: Ian Molton (spyro@f2s.com) */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.nr_irqs = ESERIES_NR_IRQS,
.init_irq = pxa25x_init_irq,
MACHINE_START(E350, "Toshiba e350")
/* Maintainer: Ian Molton (spyro@f2s.com) */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.nr_irqs = ESERIES_NR_IRQS,
.init_irq = pxa25x_init_irq,
MACHINE_START(E400, "Toshiba e400")
/* Maintainer: Ian Molton (spyro@f2s.com) */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.nr_irqs = ESERIES_NR_IRQS,
.init_irq = pxa25x_init_irq,
MACHINE_START(E740, "Toshiba e740")
/* Maintainer: Ian Molton (spyro@f2s.com) */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.nr_irqs = ESERIES_NR_IRQS,
.init_irq = pxa25x_init_irq,
MACHINE_START(E750, "Toshiba e750")
/* Maintainer: Ian Molton (spyro@f2s.com) */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.nr_irqs = ESERIES_NR_IRQS,
.init_irq = pxa25x_init_irq,
MACHINE_START(E800, "Toshiba e800")
/* Maintainer: Ian Molton (spyro@f2s.com) */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.nr_irqs = ESERIES_NR_IRQS,
.init_irq = pxa25x_init_irq,
}
MACHINE_START(EZX_A780, "Motorola EZX A780")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = EZX_NR_IRQS,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(EZX_E680, "Motorola EZX E680")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = EZX_NR_IRQS,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(EZX_A1200, "Motorola EZX A1200")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = EZX_NR_IRQS,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(EZX_A910, "Motorola EZX A910")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = EZX_NR_IRQS,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(EZX_E6, "Motorola EZX E6")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = EZX_NR_IRQS,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(EZX_E2, "Motorola EZX E2")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = EZX_NR_IRQS,
.init_irq = pxa27x_init_irq,
* initialization stuff for PXA machines which can be overridden later if
* need be.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach-types.h>
#include <mach/reset.h>
-#include <mach/gpio.h>
#include <mach/smemc.h>
#include <mach/pxa3xx-regs.h>
}
MACHINE_START(GUMSTIX, "Gumstix")
- .boot_params = 0xa0000100, /* match u-boot bi_boot_params */
+ .atag_offset = 0x100, /* match u-boot bi_boot_params */
.map_io = pxa25x_map_io,
.init_irq = pxa25x_init_irq,
.handle_irq = pxa25x_handle_irq,
}
MACHINE_START(H5400, "HP iPAQ H5000")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.init_irq = pxa25x_init_irq,
.handle_irq = pxa25x_handle_irq,
MACHINE_START(HIMALAYA, "HTC Himalaya")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.init_irq = pxa25x_init_irq,
.handle_irq = pxa25x_handle_irq,
}
MACHINE_START(H4700, "HP iPAQ HX4700")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = HX4700_NR_IRQS,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(ICONTROL, "iControl/SafeTcam boards using Embedian MXM-8x10 CoM")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
.handle_irq = pxa3xx_handle_irq,
#ifndef __ASM_ARCH_LITTLETON_H
#define __ASM_ARCH_LITTLETON_H
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#define LITTLETON_ETH_PHYS 0x30000000
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include "generic.h"
}
MACHINE_START(LITTLETON, "Marvell Form Factor Development Platform (aka Littleton)")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.nr_irqs = LITTLETON_NR_IRQS,
.init_irq = pxa3xx_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/syscore_ops.h>
#include <asm/mach/flash.h>
#include <mach/pxa27x.h>
-#include <mach/gpio.h>
#include <mach/lpd270.h>
#include <mach/audio.h>
#include <mach/pxafb.h>
MACHINE_START(LOGICPD_PXA270, "LogicPD PXA270 Card Engine")
/* Maintainer: Peter Barada */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = lpd270_map_io,
.nr_irqs = LPD270_NR_IRQS,
.init_irq = lpd270_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/hardware/sa1111.h>
#include <mach/pxa25x.h>
-#include <mach/gpio.h>
#include <mach/audio.h>
#include <mach/lubbock.h>
#include <mach/udc.h>
MACHINE_START(MAGICIAN, "HTC Magician")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.nr_irqs = MAGICIAN_NR_IRQS,
.init_irq = pxa27x_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/syscore_ops.h>
#include <asm/mach/flash.h>
#include <mach/pxa27x.h>
-#include <mach/gpio.h>
#include <mach/mainstone.h>
#include <mach/audio.h>
#include <mach/pxafb.h>
MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)")
/* Maintainer: MontaVista Software Inc. */
- .boot_params = 0xa0000100, /* BLOB boot parameter setting */
+ .atag_offset = 0x100, /* BLOB boot parameter setting */
.map_io = mainstone_map_io,
.nr_irqs = MAINSTONE_NR_IRQS,
.init_irq = mainstone_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/syscore_ops.h>
-#include <mach/gpio.h>
#include <mach/pxa2xx-regs.h>
#include <mach/mfp-pxa2xx.h>
}
MACHINE_START(MIOA701, "MIO A701")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = &pxa27x_map_io,
.init_irq = &pxa27x_init_irq,
.handle_irq = &pxa27x_handle_irq,
/* Maintainer - Michael Petchkovsky <mkpetch@internode.on.net> */
MACHINE_START(NEC_MP900, "MobilePro900/C")
- .boot_params = 0xa0220100,
+ .atag_offset = 0x220100,
.timer = &pxa_timer,
.map_io = pxa25x_map_io,
.init_irq = pxa25x_init_irq,
}
MACHINE_START(PALMLD, "Palm LifeDrive")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = palmld_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
}
MACHINE_START(PALMT5, "Palm Tungsten|T5")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.reserve = palmt5_reserve,
.init_irq = pxa27x_init_irq,
};
MACHINE_START(PALMTC, "Palm Tungsten|C")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.init_irq = pxa25x_init_irq,
.handle_irq = pxa25x_handle_irq,
}
MACHINE_START(PALMTE2, "Palm Tungsten|E2")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa25x_map_io,
.init_irq = pxa25x_init_irq,
.handle_irq = pxa25x_handle_irq,
}
MACHINE_START(TREO680, "Palm Treo 680")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.reserve = treo_reserve,
.init_irq = pxa27x_init_irq,
MACHINE_END
MACHINE_START(CENTRO, "Palm Centro 685")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.reserve = treo_reserve,
.init_irq = pxa27x_init_irq,
}
MACHINE_START(PALMTX, "Palm T|X")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = palmtx_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
}
MACHINE_START(PALMZ72, "Palm Zire72")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
MACHINE_START(PCM027, "Phytec Messtechnik GmbH phyCORE-PXA270")
/* Maintainer: Pengutronix */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pcm027_map_io,
.nr_irqs = PCM027_NR_IRQS,
.init_irq = pxa27x_init_irq,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <media/soc_camera.h>
-#include <asm/gpio.h>
#include <mach/camera.h>
#include <asm/mach/map.h>
#include <mach/pxa27x.h>
* initialization stuff for PXA machines which can be overridden later if
* need be.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/suspend.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/pxa25x.h>
#include <mach/reset.h>
#include <mach/pm.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/irq.h>
#include <asm/suspend.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
#include <mach/pxa27x.h>
#include <mach/reset.h>
#include <mach/ohci.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach/map.h>
#include <asm/suspend.h>
#include <mach/hardware.h>
-#include <mach/gpio.h>
#include <mach/pxa3xx-regs.h>
#include <mach/reset.h>
#include <mach/ohci.h>
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/syscore_ops.h>
#include <mach/hardware.h>
-#include <mach/gpio.h>
#include <mach/pxa3xx-regs.h>
#include <mach/pxa930.h>
#include <mach/reset.h>
#ifdef CONFIG_MACH_RAUMFELD_RC
MACHINE_START(RAUMFELD_RC, "Raumfeld Controller")
- .boot_params = RAUMFELD_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = raumfeld_controller_init,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
#ifdef CONFIG_MACH_RAUMFELD_CONNECTOR
MACHINE_START(RAUMFELD_CONNECTOR, "Raumfeld Connector")
- .boot_params = RAUMFELD_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = raumfeld_connector_init,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
#ifdef CONFIG_MACH_RAUMFELD_SPEAKER
MACHINE_START(RAUMFELD_SPEAKER, "Raumfeld Speaker")
- .boot_params = RAUMFELD_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = raumfeld_speaker_init,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
}, {
.name = "filesystem",
.offset = MTDPART_OFS_APPEND,
- .size = SZ_48M,
+ .size = SZ_32M + SZ_16M,
.mask_flags = 0,
}
};
MACHINE_START(SAAR, "PXA930 Handheld Platform (aka SAAR)")
/* Maintainer: Eric Miao <eric.miao@marvell.com> */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
.handle_irq = pxa3xx_handle_irq,
* it under the terms of the GNU General Public License version 2 as
* publishhed by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/i2c.h>
#include <mach/hardware.h>
#include <mach/mfp.h>
#include <mach/mfp-pxa930.h>
-#include <mach/gpio.h>
#include "generic.h"
}
MACHINE_START(SAARB, "PXA955 Handheld Platform (aka SAARB)")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.nr_irqs = SAARB_NR_IRQS,
.init_irq = pxa95x_init_irq,
.handle_irq = pxa27x_handle_irq,
.timer = &pxa_timer,
.init_machine = imote2_init,
- .boot_params = 0xA0000100,
+ .atag_offset = 0x100,
MACHINE_END
#endif
.handle_irq = pxa27x_handle_irq,
.timer = &pxa_timer,
.init_machine = stargate2_init,
- .boot_params = 0xA0000100,
+ .atag_offset = 0x100,
MACHINE_END
#endif
MACHINE_START(TAVOREVB, "PXA930 Evaluation Board (aka TavorEVB)")
/* Maintainer: Eric Miao <eric.miao@marvell.com> */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.init_irq = pxa3xx_init_irq,
.handle_irq = pxa3xx_handle_irq,
}
MACHINE_START(TAVOREVB3, "PXA950 Evaluation Board (aka TavorEVB3)")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.nr_irqs = TAVOREVB3_NR_IRQS,
.init_irq = pxa3xx_init_irq,
MACHINE_START(TRIZEPS4, "Keith und Koep Trizeps IV module")
/* MAINTAINER("Jürgen Schindele") */
- .boot_params = TRIZEPS4_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = trizeps4_init,
.map_io = trizeps4_map_io,
.init_irq = pxa27x_init_irq,
MACHINE_START(TRIZEPS4WL, "Keith und Koep Trizeps IV-WL module")
/* MAINTAINER("Jürgen Schindele") */
- .boot_params = TRIZEPS4_SDRAM_BASE + 0x100,
+ .atag_offset = 0x100,
.init_machine = trizeps4_init,
.map_io = trizeps4_map_io,
.init_irq = pxa27x_init_irq,
MACHINE_START(VIPER, "Arcom/Eurotech VIPER SBC")
/* Maintainer: Marc Zyngier <maz@misterjones.org> */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = viper_map_io,
.init_irq = viper_init_irq,
.handle_irq = pxa25x_handle_irq,
}
MACHINE_START(VPAC270, "Voipac PXA270")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
}
MACHINE_START(XCEP, "Iskratel XCEP")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.init_machine = xcep_init,
.map_io = pxa25x_map_io,
.init_irq = pxa25x_init_irq,
}
MACHINE_START(ZIPIT2, "Zipit Z2")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa27x_map_io,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
MACHINE_START(ARCOM_ZEUS, "Arcom/Eurotech ZEUS")
/* Maintainer: Marc Zyngier <maz@misterjones.org> */
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = zeus_map_io,
.nr_irqs = ZEUS_NR_IRQS,
.init_irq = zeus_init_irq,
}
MACHINE_START(ZYLONITE, "PXA3xx Platform Development Kit (aka Zylonite)")
- .boot_params = 0xa0000100,
+ .atag_offset = 0x100,
.map_io = pxa3xx_map_io,
.nr_irqs = ZYLONITE_NR_IRQS,
.init_irq = pxa3xx_init_irq,
ifeq ($(CONFIG_REALVIEW_HIGH_PHYS_OFFSET),y)
- zreladdr-y := 0x70008000
+ zreladdr-y += 0x70008000
params_phys-y := 0x70000100
initrd_phys-y := 0x70800000
else
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
endif
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
+/* empty */
MACHINE_START(REALVIEW_EB, "ARM-RealView EB")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = PLAT_PHYS_OFFSET + 0x00000100,
+ .atag_offset = 0x100,
.fixup = realview_fixup,
.map_io = realview_eb_map_io,
.init_early = realview_init_early,
MACHINE_START(REALVIEW_PB1176, "ARM-RealView PB1176")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = PLAT_PHYS_OFFSET + 0x00000100,
+ .atag_offset = 0x100,
.fixup = realview_pb1176_fixup,
.map_io = realview_pb1176_map_io,
.init_early = realview_init_early,
MACHINE_START(REALVIEW_PB11MP, "ARM-RealView PB11MPCore")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = PLAT_PHYS_OFFSET + 0x00000100,
+ .atag_offset = 0x100,
.fixup = realview_fixup,
.map_io = realview_pb11mp_map_io,
.init_early = realview_init_early,
MACHINE_START(REALVIEW_PBA8, "ARM-RealView PB-A8")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = PLAT_PHYS_OFFSET + 0x00000100,
+ .atag_offset = 0x100,
.fixup = realview_fixup,
.map_io = realview_pba8_map_io,
.init_early = realview_init_early,
MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = PLAT_PHYS_OFFSET + 0x00000100,
+ .atag_offset = 0x100,
.fixup = realview_pbx_fixup,
.map_io = realview_pbx_map_io,
.init_early = realview_init_early,
- zreladdr-y := 0x10008000
+ zreladdr-y += 0x10008000
params_phys-y := 0x10000100
initrd_phys-y := 0x18000000
#define EASI_SIZE 0x08000000 /* EASI I/O */
#define EASI_START 0x08000000
-#define EASI_BASE 0xe5000000
+#define EASI_BASE IOMEM(0xe5000000)
#define IO_START 0x03000000 /* I/O */
#define IO_SIZE 0x01000000
/*
* IO Addresses
*/
-#define VIDC_BASE IOMEM(0xe0400000)
-#define EXPMASK_BASE 0xe0360000
-#define IOMD_BASE IOMEM(0xe0200000)
-#define IOC_BASE IOMEM(0xe0200000)
-#define PCIO_BASE IOMEM(0xe0010000)
-#define FLOPPYDMA_BASE IOMEM(0xe002a000)
+#define ECARD_EASI_BASE (EASI_BASE)
+#define VIDC_BASE (IO_BASE + 0x00400000)
+#define EXPMASK_BASE (IO_BASE + 0x00360000)
+#define ECARD_IOC4_BASE (IO_BASE + 0x00270000)
+#define ECARD_IOC_BASE (IO_BASE + 0x00240000)
+#define IOMD_BASE (IO_BASE + 0x00200000)
+#define IOC_BASE (IO_BASE + 0x00200000)
+#define ECARD_MEMC8_BASE (IO_BASE + 0x0002b000)
+#define FLOPPYDMA_BASE (IO_BASE + 0x0002a000)
+#define PCIO_BASE (IO_BASE + 0x00010000)
+#define ECARD_MEMC_BASE (IO_BASE + 0x00000000)
#define vidc_writel(val) __raw_writel(val, VIDC_BASE)
-#define IO_EC_EASI_BASE 0x81400000
-#define IO_EC_IOC4_BASE 0x8009c000
-#define IO_EC_IOC_BASE 0x80090000
-#define IO_EC_MEMC8_BASE 0x8000ac00
-#define IO_EC_MEMC_BASE 0x80000000
-
#define NETSLOT_BASE 0x0302b000
#define NETSLOT_SIZE 0x00001000
#include <mach/hardware.h>
-#define IO_SPACE_LIMIT 0xffffffff
+#define IO_SPACE_LIMIT 0xffff
/*
- * We use two different types of addressing - PC style addresses, and ARM
- * addresses. PC style accesses the PC hardware with the normal PC IO
- * addresses, eg 0x3f8 for serial#1. ARM addresses are 0x80000000+
- * and are translated to the start of IO. Note that all addresses are
- * shifted left!
- */
-#define __PORT_PCIO(x) (!((x) & 0x80000000))
-
-/*
- * Dynamic IO functions.
- */
-static inline void __outb (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "strb %1, [%0, %2, lsl #2] @ outb"
- : "=&r" (temp)
- : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-static inline void __outw (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "str %1, [%0, %2, lsl #2] @ outw"
- : "=&r" (temp)
- : "r" (value|value<<16), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-static inline void __outl (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "str %1, [%0, %2, lsl #2] @ outl"
- : "=&r" (temp)
- : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-#define DECLARE_DYN_IN(sz,fnsuffix,instr) \
-static inline unsigned sz __in##fnsuffix (unsigned int port) \
-{ \
- unsigned long temp, value; \
- __asm__ __volatile__( \
- "tst %2, #0x80000000\n\t" \
- "mov %0, %4\n\t" \
- "addeq %0, %0, %3\n\t" \
- "ldr" instr " %1, [%0, %2, lsl #2] @ in" #fnsuffix \
- : "=&r" (temp), "=r" (value) \
- : "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE) \
- : "cc"); \
- return (unsigned sz)value; \
-}
-
-static inline void __iomem *__deprecated __ioaddr(unsigned int port)
-{
- void __iomem *ret;
- if (__PORT_PCIO(port))
- ret = PCIO_BASE;
- else
- ret = IO_BASE;
- return ret + (port << 2);
-}
-
-#define DECLARE_IO(sz,fnsuffix,instr) \
- DECLARE_DYN_IN(sz,fnsuffix,instr)
-
-DECLARE_IO(char,b,"b")
-DECLARE_IO(short,w,"")
-DECLARE_IO(int,l,"")
-
-#undef DECLARE_IO
-#undef DECLARE_DYN_IN
-
-/*
- * Constant address IO functions
+ * We need PC style IO addressing for:
+ * - floppy (at 0x3f2,0x3f4,0x3f5,0x3f7)
+ * - parport (at 0x278-0x27a, 0x27b-0x27f, 0x778-0x77a)
+ * - 8250 serial (only for compile)
*
- * These have to be macros for the 'J' constraint to work -
- * +/-4096 immediate operand.
+ * These peripherals are found in an area of MMIO which looks very much
+ * like an ISA bus, but with registers at the low byte of each word.
*/
-#define __outbc(value,port) \
-({ \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "strb %0, [%1, %2] @ outbc" \
- : : "r" (value), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "strb %0, [%1, %2] @ outbc" \
- : : "r" (value), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inbc(port) \
-({ \
- unsigned char result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldrb %0, [%1, %2] @ inbc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldrb %0, [%1, %2] @ inbc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result; \
-})
-
-#define __outwc(value,port) \
-({ \
- unsigned long __v = value; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outwc" \
- : : "r" (__v|__v<<16), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outwc" \
- : : "r" (__v|__v<<16), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inwc(port) \
-({ \
- unsigned short result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inwc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inwc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result & 0xffff; \
-})
-
-#define __outlc(value,port) \
-({ \
- unsigned long __v = value; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outlc" \
- : : "r" (__v), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outlc" \
- : : "r" (__v), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inlc(port) \
-({ \
- unsigned long result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inlc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inlc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result; \
-})
-
-#define inb(p) (__builtin_constant_p((p)) ? __inbc(p) : __inb(p))
-#define inw(p) (__builtin_constant_p((p)) ? __inwc(p) : __inw(p))
-#define inl(p) (__builtin_constant_p((p)) ? __inlc(p) : __inl(p))
-#define outb(v,p) (__builtin_constant_p((p)) ? __outbc(v,p) : __outb(v,p))
-#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
-#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
-
-/* the following macro is deprecated */
-#define ioaddr(port) ((unsigned long)__ioaddr((port)))
-
-#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l)
-#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l)
-
-#define outsb(p,d,l) __raw_writesb(__ioaddr(p),d,l)
-#define outsw(p,d,l) __raw_writesw(__ioaddr(p),d,l)
+#define __io(a) (PCIO_BASE + ((a) << 2))
/*
* 1:1 mapping for ioremapped regions.
.length = IO_SIZE ,
.type = MT_DEVICE
}, { /* EASI space */
- .virtual = EASI_BASE,
+ .virtual = (unsigned long)EASI_BASE,
.pfn = __phys_to_pfn(EASI_START),
.length = EASI_SIZE,
.type = MT_DEVICE
MACHINE_START(RISCPC, "Acorn-RiscPC")
/* Maintainer: Russell King */
- .boot_params = 0x10000100,
+ .atag_offset = 0x100,
.reserve_lp0 = 1,
.reserve_lp1 = 1,
.map_io = rpc_map_io,
ifeq ($(CONFIG_PM_H1940),y)
- zreladdr-y := 0x30108000
+ zreladdr-y += 0x30108000
params_phys-y := 0x30100100
else
- zreladdr-y := 0x30008000
+ zreladdr-y += 0x30008000
params_phys-y := 0x30000100
endif
* published by the Free Software Foundation.
*/
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* some boards require extra gpio capacity to support external
* devices that need GPIO.
*/
#define ARCH_NR_GPIOS (256 + CONFIG_S3C24XX_GPIO_EXTRA)
#endif
-#include <asm-generic/gpio.h>
#include <mach/gpio-nrs.h>
#include <mach/gpio-fns.h>
#ifndef __ASM_ARCH_H1940_LATCH_H
#define __ASM_ARCH_H1940_LATCH_H
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#define H1940_LATCH_GPIO(x) (S3C_GPIO_END + (x))
#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
#define __ioaddr(p) (__builtin_constant_p((p)) ? __ioaddr(p) : __ioaddrc(p))
-/* the following macro is deprecated */
-#define ioaddr(port) __ioaddr((port))
#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l)
#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l)
}
MACHINE_START(AML_M5900, "AML_M5900")
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = amlm5900_map_io,
.init_irq = s3c24xx_init_irq,
.init_machine = amlm5900_init,
MACHINE_START(BAST, "Simtec-BAST")
/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = bast_map_io,
.init_irq = s3c24xx_init_irq,
.init_machine = bast_init,
MACHINE_START(H1940, "IPAQ-H1940")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = h1940_map_io,
.reserve = h1940_reserve,
.init_irq = h1940_init_irq,
/* Maintainer: Christer Weinigel <christer@weinigel.se>,
Ben Dooks <ben-linux@fluff.org>
*/
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.timer = &s3c24xx_timer,
.init_machine = n30_init,
.init_irq = s3c24xx_init_irq,
MACHINE_START(N35, "Acer-N35")
/* Maintainer: Christer Weinigel <christer@weinigel.se>
*/
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.timer = &s3c24xx_timer,
.init_machine = n30_init,
.init_irq = s3c24xx_init_irq,
MACHINE_START(OTOM, "Nex Vision - Otom 1.1")
/* Maintainer: Guillaume GOURAT <guillaume.gourat@nexvision.tv> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = otom11_map_io,
.init_machine = otom11_init,
.init_irq = s3c24xx_init_irq,
}
MACHINE_START(QT2410, "QT2410")
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = qt2410_map_io,
.init_irq = s3c24xx_init_irq,
.init_machine = qt2410_machine_init,
MACHINE_START(SMDK2410, "SMDK2410") /* @TODO: request a new identifier and switch
* to SMDK2410 */
/* Maintainer: Jonas Dietsche */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = smdk2410_map_io,
.init_irq = s3c24xx_init_irq,
.init_machine = smdk2410_init,
}
MACHINE_START(TCT_HAMMER, "TCT_HAMMER")
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = tct_hammer_map_io,
.init_irq = s3c24xx_init_irq,
.init_machine = tct_hammer_init,
MACHINE_START(VR1000, "Thorcom-VR1000")
/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = vr1000_map_io,
.init_machine = vr1000_init,
.init_irq = s3c24xx_init_irq,
MACHINE_START(JIVE, "JIVE")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c24xx_init_irq,
.map_io = jive_map_io,
MACHINE_START(S3C2413, "S3C2413")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.fixup = smdk2413_fixup,
.init_irq = s3c24xx_init_irq,
MACHINE_START(SMDK2412, "SMDK2412")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.fixup = smdk2413_fixup,
.init_irq = s3c24xx_init_irq,
MACHINE_START(SMDK2413, "SMDK2413")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.fixup = smdk2413_fixup,
.init_irq = s3c24xx_init_irq,
}
MACHINE_START(VSTMS, "VSTMS")
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.fixup = vstms_fixup,
.init_irq = s3c24xx_init_irq,
MACHINE_START(SMDK2416, "SMDK2416")
/* Maintainer: Yauhen Kharuzhy <jekhor@gmail.com> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c24xx_init_irq,
.map_io = smdk2416_map_io,
MACHINE_START(ANUBIS, "Simtec-Anubis")
/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = anubis_map_io,
.init_machine = anubis_init,
.init_irq = s3c24xx_init_irq,
MACHINE_START(AT2440EVB, "AT2440EVB")
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = at2440evb_map_io,
.init_machine = at2440evb_init,
.init_irq = s3c24xx_init_irq,
MACHINE_START(NEO1973_GTA02, "GTA02")
/* Maintainer: Nelson Castillo <arhuaco@freaks-unidos.net> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = gta02_map_io,
.init_irq = s3c24xx_init_irq,
.init_machine = gta02_machine_init,
MACHINE_START(MINI2440, "MINI2440")
/* Maintainer: Michel Pollet <buserror@gmail.com> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = mini2440_map_io,
.init_machine = mini2440_init,
.init_irq = s3c24xx_init_irq,
MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440")
/* Maintainer: Guillaume GOURAT <guillaume.gourat@nexvision.tv> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = nexcoder_map_io,
.init_machine = nexcoder_init,
.init_irq = s3c24xx_init_irq,
MACHINE_START(OSIRIS, "Simtec-OSIRIS")
/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = osiris_map_io,
.init_irq = s3c24xx_init_irq,
.init_machine = osiris_init,
MACHINE_START(RX1950, "HP iPAQ RX1950")
/* Maintainers: Vasily Khoruzhick */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = rx1950_map_io,
.reserve = rx1950_reserve,
.init_irq = s3c24xx_init_irq,
MACHINE_START(RX3715, "IPAQ-RX3715")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.map_io = rx3715_map_io,
.reserve = rx3715_reserve,
.init_irq = rx3715_init_irq,
MACHINE_START(S3C2440, "SMDK2440")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c24xx_init_irq,
.map_io = smdk2440_map_io,
MACHINE_START(SMDK2443, "SMDK2443")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C2410_SDRAM_PA + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c24xx_init_irq,
.map_io = smdk2443_map_io,
- zreladdr-y := 0x50008000
+ zreladdr-y += 0x50008000
params_phys-y := 0x50000100
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/io.h>
+#include <linux/dma-mapping.h>
#include <mach/hardware.h>
#include <mach/map.h>
/* initialise the io descriptors we need for initialisation */
iotable_init(s3c_iodesc, ARRAY_SIZE(s3c_iodesc));
iotable_init(mach_desc, size);
+ init_consistent_dma_size(SZ_8M);
idcode = __raw_readl(S3C_VA_SYS + 0x118);
if (!idcode) {
* published by the Free Software Foundation.
*/
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* GPIO bank sizes */
#define S3C64XX_GPIO_A_NR (8)
#define S3C64XX_GPIO_B_NR (7)
#define BOARD_NR_GPIOS 16
#define ARCH_NR_GPIOS (GPIO_BOARD_START + BOARD_NR_GPIOS)
-
-#include <asm-generic/gpio.h>
#define PLAT_PHYS_OFFSET UL(0x50000000)
-#define CONSISTENT_DMA_SIZE SZ_8M
-
#endif
MACHINE_START(ANW6410, "A&W6410")
/* Maintainer: Kwangwoo Lee <kwangwoo.lee@gmail.com> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = anw6410_map_io,
MACHINE_START(WLF_CRAGG_6410, "Wolfson Cragganmore 6410")
/* Maintainer: Mark Brown <broonie@opensource.wolfsonmicro.com> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = crag6410_map_io,
.init_machine = crag6410_machine_init,
MACHINE_START(HMT, "Airgoo-HMT")
/* Maintainer: Peter Korsgaard <jacmet@sunsite.dk> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = hmt_map_io,
.init_machine = hmt_machine_init,
MACHINE_START(MINI6410, "MINI6410")
/* Maintainer: Darius Augulis <augulis.darius@gmail.com> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = mini6410_map_io,
.init_machine = mini6410_machine_init,
MACHINE_START(NCP, "NCP")
/* Maintainer: Samsung Electronics */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = ncp_map_io,
.init_machine = ncp_machine_init,
MACHINE_START(REAL6410, "REAL6410")
/* Maintainer: Darius Augulis <augulis.darius@gmail.com> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = real6410_map_io,
MACHINE_START(SMARTQ5, "SmartQ 5")
/* Maintainer: Maurus Cuelenaere <mcuelenaere AT gmail DOT com> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = smartq_map_io,
.init_machine = smartq5_machine_init,
MACHINE_START(SMARTQ7, "SmartQ 7")
/* Maintainer: Maurus Cuelenaere <mcuelenaere AT gmail DOT com> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = smartq_map_io,
.init_machine = smartq7_machine_init,
MACHINE_START(SMDK6400, "SMDK6400")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6400_init_irq,
.map_io = smdk6400_map_io,
MACHINE_START(SMDK6410, "SMDK6410")
/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
- .boot_params = S3C64XX_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s3c6410_init_irq,
.map_io = smdk6410_map_io,
- zreladdr-y := 0x20008000
+ zreladdr-y += 0x20008000
params_phys-y := 0x20000100
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/sched.h>
+#include <linux/dma-mapping.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
iotable_init(s5p64x0_iodesc, ARRAY_SIZE(s5p64x0_iodesc));
iotable_init(s5p6440_iodesc, ARRAY_SIZE(s5p6440_iodesc));
+ init_consistent_dma_size(SZ_8M);
}
void __init s5p6450_map_io(void)
iotable_init(s5p64x0_iodesc, ARRAY_SIZE(s5p64x0_iodesc));
iotable_init(s5p6450_iodesc, ARRAY_SIZE(s5p6450_iodesc));
+ init_consistent_dma_size(SZ_8M);
}
/*
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* GPIO bank sizes */
#define S5P6440_GPIO_A_NR (6)
#define ARCH_NR_GPIOS (S5P64X0_GPIO_END + CONFIG_SAMSUNG_GPIO_EXTRA)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
#define __ASM_ARCH_MEMORY_H __FILE__
#define PLAT_PHYS_OFFSET UL(0x20000000)
-#define CONSISTENT_DMA_SIZE SZ_8M
#endif /* __ASM_ARCH_MEMORY_H */
MACHINE_START(SMDK6440, "SMDK6440")
/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
- .boot_params = S5P64X0_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5p6440_init_irq,
.map_io = smdk6440_map_io,
MACHINE_START(SMDK6450, "SMDK6450")
/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
- .boot_params = S5P64X0_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5p6450_init_irq,
.map_io = smdk6450_map_io,
- zreladdr-y := 0x20008000
+ zreladdr-y += 0x20008000
params_phys-y := 0x20000100
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* GPIO bank sizes */
#define S5PC100_GPIO_A0_NR (8)
#define S5PC100_GPIO_A1_NR (5)
/* define the number of gpios we need to the one after the MP04() range */
#define ARCH_NR_GPIOS (S5PC100_GPIO_END + 1)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
MACHINE_START(SMDKC100, "SMDKC100")
/* Maintainer: Byungho Min <bhmin@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5pc100_init_irq,
.map_io = smdkc100_map_io,
.init_machine = smdkc100_machine_init,
- zreladdr-y := 0x20008000
+ zreladdr-y += 0x20008000
params_phys-y := 0x20000100
#include <linux/sysdev.h>
#include <linux/platform_device.h>
#include <linux/sched.h>
+#include <linux/dma-mapping.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
void __init s5pv210_map_io(void)
{
iotable_init(s5pv210_iodesc, ARRAY_SIZE(s5pv210_iodesc));
+ init_consistent_dma_size(14 << 20);
/* initialise device information early */
s5pv210_default_sdhci0();
#ifndef __ASM_ARCH_GPIO_H
#define __ASM_ARCH_GPIO_H __FILE__
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
/* Practically, GPIO banks up to MP03 are the configurable gpio banks */
/* GPIO bank sizes */
#define ARCH_NR_GPIOS (S5PV210_MP05(S5PV210_GPIO_MP05_NR) + \
CONFIG_SAMSUNG_GPIO_EXTRA + 1)
-#include <asm-generic/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
#define __ASM_ARCH_MEMORY_H
#define PLAT_PHYS_OFFSET UL(0x20000000)
-#define CONSISTENT_DMA_SIZE (SZ_8M + SZ_4M + SZ_2M)
/*
* Sparsemem support
/* Maintainers:
Marek Szyprowski <m.szyprowski@samsung.com>
Kyungmin Park <kyungmin.park@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5pv210_init_irq,
.map_io = aquila_map_io,
.init_machine = aquila_machine_init,
MACHINE_START(GONI, "GONI")
/* Maintainers: Kyungmin Park <kyungmin.park@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5pv210_init_irq,
.map_io = goni_map_io,
.init_machine = goni_machine_init,
MACHINE_START(SMDKC110, "SMDKC110")
/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5pv210_init_irq,
.map_io = smdkc110_map_io,
.init_machine = smdkc110_machine_init,
MACHINE_START(SMDKV210, "SMDKV210")
/* Maintainer: Kukjin Kim <kgene.kim@samsung.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5pv210_init_irq,
.map_io = smdkv210_map_io,
.init_machine = smdkv210_machine_init,
MACHINE_START(TORBRECK, "TORBRECK")
/* Maintainer: Hyunchul Ko <ghcstop@gmail.com> */
- .boot_params = S5P_PA_SDRAM + 0x100,
+ .atag_offset = 0x100,
.init_irq = s5pv210_init_irq,
.map_io = torbreck_map_io,
.init_machine = torbreck_machine_init,
#
# Common support
-obj-y := clock.o generic.o gpio.o irq.o dma.o time.o #nmi-oopser.o
+obj-y := clock.o generic.o irq.o dma.o time.o #nmi-oopser.o
obj-m :=
obj-n :=
obj- :=
- zreladdr-y := 0xc0008000
ifeq ($(CONFIG_ARCH_SA1100),y)
- zreladdr-$(CONFIG_SA1111) := 0xc0208000
+ zreladdr-$(CONFIG_SA1111) += 0xc0208000
+else
+ zreladdr-y += 0xc0008000
endif
params_phys-y := 0xc0000100
initrd_phys-y := 0xc0800000
MACHINE_START(ASSABET, "Intel-Assabet")
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.fixup = fixup_assabet,
.map_io = assabet_map_io,
.init_irq = sa1100_init_irq,
}
MACHINE_START(BADGE4, "Hewlett-Packard Laboratories BadgePAD 4")
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = badge4_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <asm/irq.h>
-#include <asm/gpio.h>
#include "generic.h"
}
MACHINE_START(H3100, "Compaq iPAQ H3100")
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = h3100_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
}
MACHINE_START(H3600, "Compaq iPAQ H3600")
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = h3600_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
*/
MACHINE_START(HACKKIT, "HackKit Cpu Board")
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = hackkit_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
#include <asm/irq.h>
#include <asm-generic/gpio.h>
+#define __ARM_GPIOLIB_COMPLEX
+
static inline int gpio_get_value(unsigned gpio)
{
if (__builtin_constant_p(gpio) && (gpio <= GPIO_MAX))
#define gpio_to_irq(gpio) ((gpio < 11) ? (IRQ_GPIO0 + gpio) : \
(IRQ_GPIO11 - 11 + gpio))
-#define irq_to_gpio(irq) ((irq < IRQ_GPIO11_27) ? (irq - IRQ_GPIO0) : \
- (irq - IRQ_GPIO11 + 11))
#endif
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffffffff
-
/*
- * We don't actually have real ISA nor PCI buses, but there is so many
- * drivers out there that might just work if we fake them...
+ * __io() is required to be an equivalent mapping to __mem_pci() for
+ * SOC_COMMON to work.
*/
#define __io(a) __typesafe_io(a)
#define __mem_pci(a) (a)
MACHINE_START(JORNADA720, "HP Jornada 720")
/* Maintainer: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> */
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = jornada720_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
}
MACHINE_START(LART, "LART")
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = lart_map_io,
.init_irq = sa1100_init_irq,
.init_machine = lart_init,
}
MACHINE_START(NANOENGINE, "BSE nanoEngine")
- .boot_params = 0xc0000000,
+ .atag_offset = 0x100,
.map_io = nanoengine_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
}
MACHINE_START(SHANNON, "Shannon (AKA: Tuxscreen)")
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = shannon_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
MACHINE_START(SIMPAD, "Simpad")
/* Maintainer: Holger Freyther */
- .boot_params = 0xc0000100,
+ .atag_offset = 0x100,
.map_io = simpad_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
- zreladdr-y := 0x08008000
+ zreladdr-y += 0x08008000
MACHINE_START(SHARK, "Shark")
/* Maintainer: Alexander Schulz */
- .boot_params = 0x08003000,
+ .atag_offset = 0x3000,
.map_io = shark_map_io,
.init_irq = shark_init_irq,
.timer = &shark_timer,
__ZRELADDR := $(shell /bin/bash -c 'printf "0x%08x" \
$$[$(CONFIG_MEMORY_START) + 0x8000]')
- zreladdr-y := $(__ZRELADDR)
+ zreladdr-y += $(__ZRELADDR)
# Unsupported legacy stuff
#
#include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/mfd/tmio.h>
#include <linux/sh_clk.h>
+#include <linux/dma-mapping.h>
#include <video/sh_mobile_lcdc.h>
#include <video/sh_mipi_dsi.h>
#include <sound/sh_fsi.h>
static void __init ag5evm_map_io(void)
{
iotable_init(ag5evm_io_desc, ARRAY_SIZE(ag5evm_io_desc));
+ /* DMA memory at 0xf6000000 - 0xffdfffff */
+ init_consistent_dma_size(158 << 20);
/* setup early devices and console here as well */
sh73a0_add_early_devices();
#include <linux/leds.h>
#include <linux/input/sh_keysc.h>
#include <linux/usb/r8a66597.h>
+#include <linux/dma-mapping.h>
#include <media/sh_mobile_ceu.h>
#include <media/sh_mobile_csi2.h>
static void __init ap4evb_map_io(void)
{
iotable_init(ap4evb_io_desc, ARRAY_SIZE(ap4evb_io_desc));
+ /* DMA memory at 0xf6000000 - 0xffdfffff */
+ init_consistent_dma_size(158 << 20);
/* setup early devices and console here as well */
sh7372_add_early_devices();
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/input/sh_keysc.h>
+#include <linux/dma-mapping.h>
#include <mach/sh7367.h>
#include <mach/common.h>
#include <asm/mach-types.h>
static void __init g3evm_map_io(void)
{
iotable_init(g3evm_io_desc, ARRAY_SIZE(g3evm_io_desc));
+ /* DMA memory at 0xf6000000 - 0xffdfffff */
+ init_consistent_dma_size(158 << 20);
/* setup early devices and console here as well */
sh7367_add_early_devices();
#include <linux/mmc/host.h>
#include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/gpio.h>
+#include <linux/dma-mapping.h>
#include <mach/sh7377.h>
#include <mach/common.h>
#include <asm/mach-types.h>
static void __init g4evm_map_io(void)
{
iotable_init(g4evm_io_desc, ARRAY_SIZE(g4evm_io_desc));
+ /* DMA memory at 0xf6000000 - 0xffdfffff */
+ init_consistent_dma_size(158 << 20);
/* setup early devices and console here as well */
sh7377_add_early_devices();
#include <linux/tca6416_keypad.h>
#include <linux/usb/r8a66597.h>
#include <linux/usb/renesas_usbhs.h>
+#include <linux/dma-mapping.h>
#include <video/sh_mobile_hdmi.h>
#include <video/sh_mobile_lcdc.h>
static void __init mackerel_map_io(void)
{
iotable_init(mackerel_io_desc, ARRAY_SIZE(mackerel_io_desc));
+ /* DMA memory at 0xf6000000 - 0xffdfffff */
+ init_consistent_dma_size(158 << 20);
/* setup early devices and console here as well */
sh7372_add_early_devices();
#ifdef CONFIG_GPIOLIB
-static inline int gpio_get_value(unsigned gpio)
-{
- return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- __gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
- return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
- return __gpio_to_irq(gpio);
-}
-
static inline int irq_to_gpio(unsigned int irq)
{
return -ENOSYS;
}
+#else
+
+#define __ARM_GPIOLIB_COMPLEX
+
#endif /* CONFIG_GPIOLIB */
#endif /* __ASM_ARCH_GPIO_H */
#define PLAT_PHYS_OFFSET UL(CONFIG_MEMORY_START)
#define MEM_SIZE UL(CONFIG_MEMORY_SIZE)
-/* DMA memory at 0xf6000000 - 0xffdfffff */
-#define CONSISTENT_DMA_SIZE (158 << 20)
-
#endif /* __ASM_MACH_MEMORY_H */
-zreladdr-y := 0x00008000
+zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
}
MACHINE_START(SPEAR300, "ST-SPEAR300-EVB")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = spear3xx_map_io,
.init_irq = spear3xx_init_irq,
.timer = &spear3xx_timer,
}
MACHINE_START(SPEAR310, "ST-SPEAR310-EVB")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = spear3xx_map_io,
.init_irq = spear3xx_init_irq,
.timer = &spear3xx_timer,
}
MACHINE_START(SPEAR320, "ST-SPEAR320-EVB")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = spear3xx_map_io,
.init_irq = spear3xx_init_irq,
.timer = &spear3xx_timer,
-zreladdr-y := 0x00008000
+zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
}
MACHINE_START(SPEAR600, "ST-SPEAR600-EVB")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = spear6xx_map_io,
.init_irq = spear6xx_init_irq,
.timer = &spear6xx_timer,
- zreladdr-y := 0x20008000
+ zreladdr-y += 0x20008000
params_phys-y := 0x20000100
initrd_phys-y := 0x20800000
}
MACHINE_START(TCC8000_SDK, "Telechips TCC8000-SDK Demo Board")
- .boot_params = PLAT_PHYS_OFFSET + 0x00000100,
+ .atag_offset = 0x100,
.map_io = tcc8k_map_io,
.init_irq = tcc8k_init_irq,
.init_machine = tcc8k_init,
-zreladdr-$(CONFIG_ARCH_TEGRA_2x_SOC) := 0x00008000
+zreladdr-$(CONFIG_ARCH_TEGRA_2x_SOC) += 0x00008000
params_phys-$(CONFIG_ARCH_TEGRA_2x_SOC) := 0x00000100
initrd_phys-$(CONFIG_ARCH_TEGRA_2x_SOC) := 0x00800000
}
MACHINE_START(HARMONY, "harmony")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.fixup = tegra_harmony_fixup,
.map_io = tegra_map_common_io,
.init_early = tegra_init_early,
}
MACHINE_START(PAZ00, "Toshiba AC100 / Dynabook AZ")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.fixup = tegra_paz00_fixup,
.map_io = tegra_map_common_io,
.init_early = tegra_init_early,
MACHINE_START(SEABOARD, "seaboard")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = tegra_map_common_io,
.init_early = tegra_init_early,
.init_irq = tegra_init_irq,
MACHINE_END
MACHINE_START(KAEN, "kaen")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = tegra_map_common_io,
.init_early = tegra_init_early,
.init_irq = tegra_init_irq,
MACHINE_END
MACHINE_START(WARIO, "wario")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = tegra_map_common_io,
.init_early = tegra_init_early,
.init_irq = tegra_init_irq,
* GNU General Public License for more details.
*
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <mach/pinmux.h>
-#include <mach/gpio.h>
#include "gpio-names.h"
#include "board-trimslice.h"
}
MACHINE_START(TRIMSLICE, "trimslice")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.fixup = tegra_trimslice_fixup,
.map_io = tegra_map_common_io,
.init_early = tegra_init_early,
#ifndef __MACH_TEGRA_GPIO_H
#define __MACH_TEGRA_GPIO_H
-#include <linux/init.h>
+#include <linux/types.h>
#include <mach/irqs.h>
#define TEGRA_NR_GPIOS INT_GPIO_NR
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-
#define TEGRA_GPIO_TO_IRQ(gpio) (INT_GPIO_BASE + (gpio))
-#define TEGRA_IRQ_TO_GPIO(irq) ((irq) - INT_GPIO_BASE)
-
-static inline int gpio_to_irq(unsigned int gpio)
-{
- if (gpio < TEGRA_NR_GPIOS)
- return INT_GPIO_BASE + gpio;
- return -EINVAL;
-}
-
-static inline int irq_to_gpio(unsigned int irq)
-{
- if ((irq >= INT_GPIO_BASE) && (irq < INT_GPIO_BASE + INT_GPIO_NR))
- return irq - INT_GPIO_BASE;
- return -EINVAL;
-}
struct tegra_gpio_table {
int gpio; /* GPIO number */
# INITRD_PHYS must be in RAM
ifdef CONFIG_MACH_U300_SINGLE_RAM
- zreladdr-y := 0x28E08000
+ zreladdr-y += 0x28E08000
params_phys-y := 0x28E00100
else
- zreladdr-y := 0x48008000
+ zreladdr-y += 0x48008000
params_phys-y := 0x48000100
endif
#include <linux/err.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/fsmc.h>
+#include <linux/dma-mapping.h>
#include <asm/types.h>
#include <asm/setup.h>
void __init u300_map_io(void)
{
iotable_init(u300_io_desc, ARRAY_SIZE(u300_io_desc));
+ /* We enable a real big DMA buffer if need be. */
+ init_consistent_dma_size(SZ_4M);
}
/*
--- /dev/null
+/*
+ * Copyright (C) 2007-2011 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * GPIO block resgister definitions and inline macros for
+ * U300 GPIO COH 901 335 or COH 901 571/3
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+
+#ifndef __MACH_U300_GPIO_U300_H
+#define __MACH_U300_GPIO_U300_H
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+/* Switch type depending on platform/chip variant */
+#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
+#define U300_COH901335
+#endif
+#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
+#define U300_COH901571_3
+#endif
+
+/* Get base address for regs here */
+#include "u300-regs.h"
+/* IRQ numbers */
+#include "irqs.h"
+
+/*
+ * This is the GPIO block definitions. GPIO (General Purpose I/O) can be
+ * used for anything, and often is. The event/enable etc figures are for
+ * the lowermost pin (pin 0 on each port), shift this left to match your
+ * pin if you're gonna use these values.
+ */
+#ifdef U300_COH901335
+#define U300_GPIO_PORTX_SPACING (0x1C)
+/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
+#define U300_GPIO_PXPDIR (0x00)
+#define U300_GPIO_PXPDOR (0x00)
+/* Port X Pin Config Register 32bit (R/W) */
+#define U300_GPIO_PXPCR (0x04)
+#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
+#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
+#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
+/* Port X Interrupt Event Register 32bit (R/W) */
+#define U300_GPIO_PXIEV (0x08)
+#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
+#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
+/* Port X Interrupt Enable Register 32bit (R/W) */
+#define U300_GPIO_PXIEN (0x0C)
+#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
+#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
+/* Port X Interrupt Force Register 32bit (R/W) */
+#define U300_GPIO_PXIFR (0x10)
+#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
+#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
+/* Port X Interrupt Config Register 32bit (R/W) */
+#define U300_GPIO_PXICR (0x14)
+#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
+/* Port X Pull-up Enable Register 32bit (R/W) */
+#define U300_GPIO_PXPER (0x18)
+#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
+#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
+/* Control Register 32bit (R/W) */
+#define U300_GPIO_CR (0x54)
+#define U300_GPIO_CR_BLOCK_CLOCK_ENABLE (0x00000001UL)
+/* three ports of 8 bits each = GPIO pins 0..23 */
+#define U300_GPIO_NUM_PORTS 3
+#define U300_GPIO_PINS_PER_PORT 8
+#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
+#endif
+
+#ifdef U300_COH901571_3
+/*
+ * Control Register 32bit (R/W)
+ * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
+ * gives the number of GPIO pins.
+ * bit 8-2 (mask 0x000001FC) contains the core version ID.
+ */
+#define U300_GPIO_CR (0x00)
+#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL)
+#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
+#define U300_GPIO_PORTX_SPACING (0x30)
+/* Port X Pin Data INPUT Register 32bit (R/W) */
+#define U300_GPIO_PXPDIR (0x04)
+/* Port X Pin Data OUTPUT Register 32bit (R/W) */
+#define U300_GPIO_PXPDOR (0x08)
+/* Port X Pin Config Register 32bit (R/W) */
+#define U300_GPIO_PXPCR (0x0C)
+#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
+#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
+#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
+/* Port X Pull-up Enable Register 32bit (R/W) */
+#define U300_GPIO_PXPER (0x10)
+#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
+#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
+/* Port X Interrupt Event Register 32bit (R/W) */
+#define U300_GPIO_PXIEV (0x14)
+#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
+#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
+/* Port X Interrupt Enable Register 32bit (R/W) */
+#define U300_GPIO_PXIEN (0x18)
+#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
+#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
+/* Port X Interrupt Force Register 32bit (R/W) */
+#define U300_GPIO_PXIFR (0x1C)
+#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
+#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
+/* Port X Interrupt Config Register 32bit (R/W) */
+#define U300_GPIO_PXICR (0x20)
+#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
+#ifdef CONFIG_MACH_U300_BS335
+/* seven ports of 8 bits each = GPIO pins 0..55 */
+#define U300_GPIO_NUM_PORTS 7
+#else
+/* five ports of 8 bits each = GPIO pins 0..39 */
+#define U300_GPIO_NUM_PORTS 5
+#endif
+#define U300_GPIO_PINS_PER_PORT 8
+#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
+#endif
+
+/*
+ * Individual pin assignments for the B26/S26. Notice that the
+ * actual usage of these pins depends on the PAD MUX settings, that
+ * is why the same number can potentially appear several times.
+ * In the reference design each pin is only used for one purpose.
+ * These were determined by inspecting the B26/S26 schematic:
+ * 2/1911-ROA 128 1603
+ */
+#ifdef CONFIG_MACH_U300_BS2X
+#define U300_GPIO_PIN_UART_RX 0
+#define U300_GPIO_PIN_UART_TX 1
+#define U300_GPIO_PIN_GPIO02 2 /* Unrouted */
+#define U300_GPIO_PIN_GPIO03 3 /* Unrouted */
+#define U300_GPIO_PIN_CAM_SLEEP 4
+#define U300_GPIO_PIN_CAM_REG_EN 5
+#define U300_GPIO_PIN_GPIO06 6 /* Unrouted */
+#define U300_GPIO_PIN_GPIO07 7 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO08 8 /* Service point SP2321 */
+#define U300_GPIO_PIN_GPIO09 9 /* Service point SP2322 */
+#define U300_GPIO_PIN_PHFSENSE 10 /* Headphone jack sensing */
+#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */
+#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */
+#define U300_GPIO_PIN_FLIPSENSE 13 /* Mechanical flip sensing */
+#define U300_GPIO_PIN_GPIO14 14 /* DSP JTAG Port RTCK */
+#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO16 16 /* Unrouted */
+#define U300_GPIO_PIN_GPIO17 17 /* Unrouted */
+#define U300_GPIO_PIN_GPIO18 18 /* Unrouted */
+#define U300_GPIO_PIN_GPIO19 19 /* Unrouted */
+#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */
+#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */
+#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */
+#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */
+#endif
+
+/*
+ * Individual pin assignments for the B330/S330 and B365/S365.
+ * Notice that the actual usage of these pins depends on the
+ * PAD MUX settings, that is why the same number can potentially
+ * appear several times. In the reference design each pin is only
+ * used for one purpose. These were determined by inspecting the
+ * S365 schematic.
+ */
+#if defined(CONFIG_MACH_U300_BS330) || defined(CONFIG_MACH_U300_BS365) || \
+ defined(CONFIG_MACH_U300_BS335)
+#define U300_GPIO_PIN_UART_RX 0
+#define U300_GPIO_PIN_UART_TX 1
+#define U300_GPIO_PIN_UART_CTS 2
+#define U300_GPIO_PIN_UART_RTS 3
+#define U300_GPIO_PIN_CAM_MAIN_STANDBY 4 /* Camera MAIN standby */
+#define U300_GPIO_PIN_GPIO05 5 /* Unrouted */
+#define U300_GPIO_PIN_MS_CD 6 /* Memory Stick Card insertion */
+#define U300_GPIO_PIN_GPIO07 7 /* Test point TP2430 */
+
+#define U300_GPIO_PIN_GPIO08 8 /* Test point TP2437 */
+#define U300_GPIO_PIN_GPIO09 9 /* Test point TP2431 */
+#define U300_GPIO_PIN_GPIO10 10 /* Test point TP2432 */
+#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */
+#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */
+#define U300_GPIO_PIN_CAM_SUB_STANDBY 13 /* Camera SUB standby */
+#define U300_GPIO_PIN_GPIO14 14 /* Test point TP2436 */
+#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO16 16 /* Test point TP2438 */
+#define U300_GPIO_PIN_PHFSENSE 17 /* Headphone jack sensing */
+#define U300_GPIO_PIN_GPIO18 18 /* Test point TP2439 */
+#define U300_GPIO_PIN_GPIO19 19 /* Routed somewhere */
+#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */
+#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */
+#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */
+#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO24 24 /* Unrouted */
+#define U300_GPIO_PIN_GPIO25 25 /* Unrouted */
+#define U300_GPIO_PIN_GPIO26 26 /* Unrouted */
+#define U300_GPIO_PIN_GPIO27 27 /* Unrouted */
+#define U300_GPIO_PIN_GPIO28 28 /* Unrouted */
+#define U300_GPIO_PIN_GPIO29 29 /* Unrouted */
+#define U300_GPIO_PIN_GPIO30 30 /* Unrouted */
+#define U300_GPIO_PIN_GPIO31 31 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO32 32 /* Unrouted */
+#define U300_GPIO_PIN_GPIO33 33 /* Unrouted */
+#define U300_GPIO_PIN_GPIO34 34 /* Unrouted */
+#define U300_GPIO_PIN_GPIO35 35 /* Unrouted */
+#define U300_GPIO_PIN_GPIO36 36 /* Unrouted */
+#define U300_GPIO_PIN_GPIO37 37 /* Unrouted */
+#define U300_GPIO_PIN_GPIO38 38 /* Unrouted */
+#define U300_GPIO_PIN_GPIO39 39 /* Unrouted */
+
+#ifdef CONFIG_MACH_U300_BS335
+
+#define U300_GPIO_PIN_GPIO40 40 /* Unrouted */
+#define U300_GPIO_PIN_GPIO41 41 /* Unrouted */
+#define U300_GPIO_PIN_GPIO42 42 /* Unrouted */
+#define U300_GPIO_PIN_GPIO43 43 /* Unrouted */
+#define U300_GPIO_PIN_GPIO44 44 /* Unrouted */
+#define U300_GPIO_PIN_GPIO45 45 /* Unrouted */
+#define U300_GPIO_PIN_GPIO46 46 /* Unrouted */
+#define U300_GPIO_PIN_GPIO47 47 /* Unrouted */
+
+#define U300_GPIO_PIN_GPIO48 48 /* Unrouted */
+#define U300_GPIO_PIN_GPIO49 49 /* Unrouted */
+#define U300_GPIO_PIN_GPIO50 50 /* Unrouted */
+#define U300_GPIO_PIN_GPIO51 51 /* Unrouted */
+#define U300_GPIO_PIN_GPIO52 52 /* Unrouted */
+#define U300_GPIO_PIN_GPIO53 53 /* Unrouted */
+#define U300_GPIO_PIN_GPIO54 54 /* Unrouted */
+#define U300_GPIO_PIN_GPIO55 55 /* Unrouted */
+#endif
+
+#endif
+
+#endif /* __MACH_U300_GPIO_U300_H */
#ifndef __MACH_U300_GPIO_H
#define __MACH_U300_GPIO_H
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-
-/* Switch type depending on platform/chip variant */
-#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330)
-#define U300_COH901335
-#endif
-#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335)
-#define U300_COH901571_3
-#endif
-
-/* Get base address for regs here */
-#include "u300-regs.h"
-/* IRQ numbers */
-#include "irqs.h"
-
-/*
- * This is the GPIO block definitions. GPIO (General Purpose I/O) can be
- * used for anything, and often is. The event/enable etc figures are for
- * the lowermost pin (pin 0 on each port), shift this left to match your
- * pin if you're gonna use these values.
- */
-#ifdef U300_COH901335
-#define U300_GPIO_PORTX_SPACING (0x1C)
-/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
-#define U300_GPIO_PXPDIR (0x00)
-#define U300_GPIO_PXPDOR (0x00)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR (0x04)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV (0x08)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN (0x0C)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR (0x10)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR (0x14)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER (0x18)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
-/* Control Register 32bit (R/W) */
-#define U300_GPIO_CR (0x54)
-#define U300_GPIO_CR_BLOCK_CLOCK_ENABLE (0x00000001UL)
-/* three ports of 8 bits each = GPIO pins 0..23 */
-#define U300_GPIO_NUM_PORTS 3
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
-
-#ifdef U300_COH901571_3
-/*
- * Control Register 32bit (R/W)
- * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
- * gives the number of GPIO pins.
- * bit 8-2 (mask 0x000001FC) contains the core version ID.
- */
-#define U300_GPIO_CR (0x00)
-#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL)
-#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL)
-#define U300_GPIO_PORTX_SPACING (0x30)
-/* Port X Pin Data INPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDIR (0x04)
-/* Port X Pin Data OUTPUT Register 32bit (R/W) */
-#define U300_GPIO_PXPDOR (0x08)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_GPIO_PXPCR (0x0C)
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_GPIO_PXPER (0x10)
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_GPIO_PXIEV (0x14)
-#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_GPIO_PXIEN (0x18)
-#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_GPIO_PXIFR (0x1C)
-#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL)
-#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_GPIO_PXICR (0x20)
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL)
-#ifdef CONFIG_MACH_U300_BS335
-/* seven ports of 8 bits each = GPIO pins 0..55 */
-#define U300_GPIO_NUM_PORTS 7
-#else
-/* five ports of 8 bits each = GPIO pins 0..39 */
-#define U300_GPIO_NUM_PORTS 5
-#endif
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1)
-#endif
-
-/*
- * Individual pin assignments for the B26/S26. Notice that the
- * actual usage of these pins depends on the PAD MUX settings, that
- * is why the same number can potentially appear several times.
- * In the reference design each pin is only used for one purpose.
- * These were determined by inspecting the B26/S26 schematic:
- * 2/1911-ROA 128 1603
- */
-#ifdef CONFIG_MACH_U300_BS2X
-#define U300_GPIO_PIN_UART_RX 0
-#define U300_GPIO_PIN_UART_TX 1
-#define U300_GPIO_PIN_GPIO02 2 /* Unrouted */
-#define U300_GPIO_PIN_GPIO03 3 /* Unrouted */
-#define U300_GPIO_PIN_CAM_SLEEP 4
-#define U300_GPIO_PIN_CAM_REG_EN 5
-#define U300_GPIO_PIN_GPIO06 6 /* Unrouted */
-#define U300_GPIO_PIN_GPIO07 7 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO08 8 /* Service point SP2321 */
-#define U300_GPIO_PIN_GPIO09 9 /* Service point SP2322 */
-#define U300_GPIO_PIN_PHFSENSE 10 /* Headphone jack sensing */
-#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */
-#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */
-#define U300_GPIO_PIN_FLIPSENSE 13 /* Mechanical flip sensing */
-#define U300_GPIO_PIN_GPIO14 14 /* DSP JTAG Port RTCK */
-#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO16 16 /* Unrouted */
-#define U300_GPIO_PIN_GPIO17 17 /* Unrouted */
-#define U300_GPIO_PIN_GPIO18 18 /* Unrouted */
-#define U300_GPIO_PIN_GPIO19 19 /* Unrouted */
-#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */
-#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */
-#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */
-#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */
-#endif
-
-/*
- * Individual pin assignments for the B330/S330 and B365/S365.
- * Notice that the actual usage of these pins depends on the
- * PAD MUX settings, that is why the same number can potentially
- * appear several times. In the reference design each pin is only
- * used for one purpose. These were determined by inspecting the
- * S365 schematic.
- */
-#if defined(CONFIG_MACH_U300_BS330) || defined(CONFIG_MACH_U300_BS365) || \
- defined(CONFIG_MACH_U300_BS335)
-#define U300_GPIO_PIN_UART_RX 0
-#define U300_GPIO_PIN_UART_TX 1
-#define U300_GPIO_PIN_UART_CTS 2
-#define U300_GPIO_PIN_UART_RTS 3
-#define U300_GPIO_PIN_CAM_MAIN_STANDBY 4 /* Camera MAIN standby */
-#define U300_GPIO_PIN_GPIO05 5 /* Unrouted */
-#define U300_GPIO_PIN_MS_CD 6 /* Memory Stick Card insertion */
-#define U300_GPIO_PIN_GPIO07 7 /* Test point TP2430 */
-
-#define U300_GPIO_PIN_GPIO08 8 /* Test point TP2437 */
-#define U300_GPIO_PIN_GPIO09 9 /* Test point TP2431 */
-#define U300_GPIO_PIN_GPIO10 10 /* Test point TP2432 */
-#define U300_GPIO_PIN_MMC_CLKRET 11 /* Clock return from MMC/SD card */
-#define U300_GPIO_PIN_MMC_CD 12 /* MMC Card insertion detection */
-#define U300_GPIO_PIN_CAM_SUB_STANDBY 13 /* Camera SUB standby */
-#define U300_GPIO_PIN_GPIO14 14 /* Test point TP2436 */
-#define U300_GPIO_PIN_GPIO15 15 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO16 16 /* Test point TP2438 */
-#define U300_GPIO_PIN_PHFSENSE 17 /* Headphone jack sensing */
-#define U300_GPIO_PIN_GPIO18 18 /* Test point TP2439 */
-#define U300_GPIO_PIN_GPIO19 19 /* Routed somewhere */
-#define U300_GPIO_PIN_GPIO20 20 /* Unrouted */
-#define U300_GPIO_PIN_GPIO21 21 /* Unrouted */
-#define U300_GPIO_PIN_GPIO22 22 /* Unrouted */
-#define U300_GPIO_PIN_GPIO23 23 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO24 24 /* Unrouted */
-#define U300_GPIO_PIN_GPIO25 25 /* Unrouted */
-#define U300_GPIO_PIN_GPIO26 26 /* Unrouted */
-#define U300_GPIO_PIN_GPIO27 27 /* Unrouted */
-#define U300_GPIO_PIN_GPIO28 28 /* Unrouted */
-#define U300_GPIO_PIN_GPIO29 29 /* Unrouted */
-#define U300_GPIO_PIN_GPIO30 30 /* Unrouted */
-#define U300_GPIO_PIN_GPIO31 31 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO32 32 /* Unrouted */
-#define U300_GPIO_PIN_GPIO33 33 /* Unrouted */
-#define U300_GPIO_PIN_GPIO34 34 /* Unrouted */
-#define U300_GPIO_PIN_GPIO35 35 /* Unrouted */
-#define U300_GPIO_PIN_GPIO36 36 /* Unrouted */
-#define U300_GPIO_PIN_GPIO37 37 /* Unrouted */
-#define U300_GPIO_PIN_GPIO38 38 /* Unrouted */
-#define U300_GPIO_PIN_GPIO39 39 /* Unrouted */
-
-#ifdef CONFIG_MACH_U300_BS335
-
-#define U300_GPIO_PIN_GPIO40 40 /* Unrouted */
-#define U300_GPIO_PIN_GPIO41 41 /* Unrouted */
-#define U300_GPIO_PIN_GPIO42 42 /* Unrouted */
-#define U300_GPIO_PIN_GPIO43 43 /* Unrouted */
-#define U300_GPIO_PIN_GPIO44 44 /* Unrouted */
-#define U300_GPIO_PIN_GPIO45 45 /* Unrouted */
-#define U300_GPIO_PIN_GPIO46 46 /* Unrouted */
-#define U300_GPIO_PIN_GPIO47 47 /* Unrouted */
-
-#define U300_GPIO_PIN_GPIO48 48 /* Unrouted */
-#define U300_GPIO_PIN_GPIO49 49 /* Unrouted */
-#define U300_GPIO_PIN_GPIO50 50 /* Unrouted */
-#define U300_GPIO_PIN_GPIO51 51 /* Unrouted */
-#define U300_GPIO_PIN_GPIO52 52 /* Unrouted */
-#define U300_GPIO_PIN_GPIO53 53 /* Unrouted */
-#define U300_GPIO_PIN_GPIO54 54 /* Unrouted */
-#define U300_GPIO_PIN_GPIO55 55 /* Unrouted */
-#endif
-
-#endif
-
-/* translates a pin number to a port number */
-#define PIN_TO_PORT(val) (val >> 3)
+#define __ARM_GPIOLIB_COMPLEX
/* These can be found in arch/arm/mach-u300/gpio.c */
extern int gpio_is_valid(int number);
#define gpio_get_value_cansleep gpio_get_value
#define gpio_set_value_cansleep gpio_set_value
+/* translates a pin number to a port number */
+#define PIN_TO_PORT(val) (val >> 3)
+
/* wrappers to sleep-enable the previous two functions */
static inline unsigned gpio_to_irq(unsigned gpio)
{
return PIN_TO_PORT(gpio) + IRQ_U300_GPIO_PORT0;
}
+#define gpio_to_irq gpio_to_irq
-static inline unsigned irq_to_gpio(unsigned irq)
-{
- /*
- * FIXME: This is no 1-1 mapping at all, it points to the
- * whole block of 8 pins.
- */
- return (irq - IRQ_U300_GPIO_PORT0) << 3;
-}
-
-#endif
+#endif /* __MACH_U300_GPIO_H */
#ifdef CONFIG_MACH_U300_DUAL_RAM
#define PLAT_PHYS_OFFSET UL(0x48000000)
-#define BOOT_PARAMS_OFFSET (PHYS_OFFSET + 0x100)
+#define BOOT_PARAMS_OFFSET 0x100
#else
#define PLAT_PHYS_OFFSET (0x28000000 + \
(CONFIG_MACH_U300_ACCESS_MEM_SIZE - \
(CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024)
+#define BOOT_PARAMS_OFFSET (0x100 + \
+ (CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1)*1024*1024*2)
#else
#define PLAT_PHYS_OFFSET (0x28000000 + \
(CONFIG_MACH_U300_ACCESS_MEM_SIZE + \
(CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024)
+#define BOOT_PARAMS_OFFSET 0x100
#endif
-#define BOOT_PARAMS_OFFSET (0x28000000 + \
- (CONFIG_MACH_U300_ACCESS_MEM_SIZE + \
- (CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024 + 0x100)
#endif
-/*
- * We enable a real big DMA buffer if need be.
- */
-#define CONSISTENT_DMA_SIZE SZ_4M
-
#endif
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/mmc/host.h>
-#include <linux/gpio.h>
#include <linux/dmaengine.h>
#include <linux/amba/mmci.h>
#include <linux/slab.h>
#include <mach/coh901318.h>
#include <mach/dma_channels.h>
+#include <mach/gpio-u300.h>
#include "mmc.h"
#include "padmux.h"
MACHINE_START(U300, MACH_U300_STRING)
/* Maintainer: Linus Walleij <linus.walleij@stericsson.com> */
- .boot_params = BOOT_PARAMS_OFFSET,
+ .atag_offset = BOOT_PARAMS_OFFSET,
.map_io = u300_map_io,
.reserve = u300_reserve,
.init_irq = u300_init_irq,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include "pins-db8500.h"
* Board data for the U8500 UIB, also known as the New UIB
* License terms: GNU General Public License (GPL), version 2
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/i2c.h>
#include <linux/mfd/tc3589x.h>
#include <linux/input/matrix_keypad.h>
-#include <mach/gpio.h>
#include <mach/irqs.h>
#include "board-mop500.h"
#include <plat/i2c.h>
#include <plat/ste_dma40.h>
#include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include <mach/setup.h>
MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
/* Maintainer: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> */
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = u8500_map_io,
.init_irq = ux500_init_irq,
/* we re-use nomadik timer here */
MACHINE_END
MACHINE_START(HREFV60, "ST-Ericsson U8500 Platform HREFv60+")
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = u8500_map_io,
.init_irq = ux500_init_irq,
.timer = &ux500_timer,
MACHINE_END
MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
- .boot_params = 0x100,
+ .atag_offset = 0x100,
.map_io = u8500_map_io,
.init_irq = ux500_init_irq,
/* we re-use nomadik timer here */
#include <linux/amba/mmci.h>
#include <linux/mmc/host.h>
-#include <linux/gpio.h>
#include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
#include <mach/db5500-regs.h>
#include <plat/ste_dma40.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/amba/bus.h>
-#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/i2c.h>
#include <plat/pincfg.h>
#include <plat/i2c.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include <mach/devices.h>
}
MACHINE_START(U5500, "ST-Ericsson U5500 Platform")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = u5500_map_io,
.init_irq = ux500_init_irq,
.timer = &ux500_timer,
#include <asm/mach/map.h>
#include <asm/pmu.h>
-#include <plat/gpio.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include <mach/devices.h>
#include <linux/amba/bus.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
-#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <asm/mach/map.h>
#include <asm/pmu.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include <mach/setup.h>
#include <mach/devices.h>
#include <linux/platform_device.h>
#include <linux/amba/bus.h>
-#include <plat/gpio.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
*/
#define ARCH_NR_GPIOS 350
-#include <plat/gpio.h>
-
#endif /* __ASM_ARCH_GPIO_H */
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
+/* empty */
MACHINE_START(VERSATILE_AB, "ARM-Versatile AB")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = versatile_map_io,
.init_early = versatile_init_early,
.init_irq = versatile_init_irq,
MACHINE_START(VERSATILE_PB, "ARM-Versatile PB")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.map_io = versatile_map_io,
.init_early = versatile_init_early,
.init_irq = versatile_init_irq,
- zreladdr-y := 0x60008000
+ zreladdr-y += 0x60008000
params_phys-y := 0x60000100
initrd_phys-y := 0x60800000
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffffffff
-
#define __io(a) __typesafe_io(a)
#define __mem_pci(a) (a)
}
MACHINE_START(VEXPRESS, "ARM-Versatile Express")
- .boot_params = PLAT_PHYS_OFFSET + 0x00000100,
+ .atag_offset = 0x100,
.map_io = v2m_map_io,
.init_early = v2m_init_early,
.init_irq = v2m_init_irq,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x01000000
}
MACHINE_START(BV07, "Benign BV07 Mini Netbook")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.reserve = vt8500_reserve_mem,
.map_io = vt8500_map_io,
.init_irq = vt8500_init_irq,
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
+/* empty */
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
#define __io(a) __typesafe_io((a) + 0xf0000000)
#define __mem_pci(a) (a)
}
MACHINE_START(WM8505_7IN_NETBOOK, "WM8505 7-inch generic netbook")
- .boot_params = 0x00000100,
+ .atag_offset = 0x100,
.reserve = wm8505_reserve_mem,
.map_io = wm8505_map_io,
.init_irq = wm8505_init_irq,
-zreladdr-y := 0x00008000
+zreladdr-y += 0x00008000
params_phys-y := 0x00000100
#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
static inline int gpio_to_irq(unsigned gpio)
{
return gpio;
}
+#define gpio_to_irq gpio_to_irq
static inline int irq_to_gpio(unsigned irq)
{
MACHINE_START(W90P910EVB, "W90P910EVB")
/* Maintainer: Wan ZongShun */
- .boot_params = 0,
.map_io = nuc910evb_map_io,
.init_irq = nuc900_init_irq,
.init_machine = nuc910evb_init,
MACHINE_START(W90P950EVB, "W90P950EVB")
/* Maintainer: Wan ZongShun */
- .boot_params = 0,
.map_io = nuc950evb_map_io,
.init_irq = nuc900_init_irq,
.init_machine = nuc950evb_init,
MACHINE_START(W90N960EVB, "W90N960EVB")
/* Maintainer: Wan ZongShun */
- .boot_params = 0,
.map_io = nuc960evb_map_io,
.init_irq = nuc900_init_irq,
.init_machine = nuc960evb_init,
- zreladdr-y := 0x00008000
+ zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
+#include <linux/err.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include <asm/cacheflush.h>
#include <asm/hardware/cache-l2x0.h>
printk(KERN_INFO "l2x0: %d ways, CACHE_ID 0x%08x, AUX_CTRL 0x%08x, Cache size: %d B\n",
ways, cache_id, aux, l2x0_size);
}
+
+#ifdef CONFIG_OF
+static void __init l2x0_of_setup(const struct device_node *np,
+ __u32 *aux_val, __u32 *aux_mask)
+{
+ u32 data[2] = { 0, 0 };
+ u32 tag = 0;
+ u32 dirty = 0;
+ u32 val = 0, mask = 0;
+
+ of_property_read_u32(np, "arm,tag-latency", &tag);
+ if (tag) {
+ mask |= L2X0_AUX_CTRL_TAG_LATENCY_MASK;
+ val |= (tag - 1) << L2X0_AUX_CTRL_TAG_LATENCY_SHIFT;
+ }
+
+ of_property_read_u32_array(np, "arm,data-latency",
+ data, ARRAY_SIZE(data));
+ if (data[0] && data[1]) {
+ mask |= L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK |
+ L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK;
+ val |= ((data[0] - 1) << L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT) |
+ ((data[1] - 1) << L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT);
+ }
+
+ of_property_read_u32(np, "arm,dirty-latency", &dirty);
+ if (dirty) {
+ mask |= L2X0_AUX_CTRL_DIRTY_LATENCY_MASK;
+ val |= (dirty - 1) << L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT;
+ }
+
+ *aux_val &= ~mask;
+ *aux_val |= val;
+ *aux_mask &= ~mask;
+}
+
+static void __init pl310_of_setup(const struct device_node *np,
+ __u32 *aux_val, __u32 *aux_mask)
+{
+ u32 data[3] = { 0, 0, 0 };
+ u32 tag[3] = { 0, 0, 0 };
+ u32 filter[2] = { 0, 0 };
+
+ of_property_read_u32_array(np, "arm,tag-latency", tag, ARRAY_SIZE(tag));
+ if (tag[0] && tag[1] && tag[2])
+ writel_relaxed(
+ ((tag[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
+ ((tag[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
+ ((tag[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
+ l2x0_base + L2X0_TAG_LATENCY_CTRL);
+
+ of_property_read_u32_array(np, "arm,data-latency",
+ data, ARRAY_SIZE(data));
+ if (data[0] && data[1] && data[2])
+ writel_relaxed(
+ ((data[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
+ ((data[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
+ ((data[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
+ l2x0_base + L2X0_DATA_LATENCY_CTRL);
+
+ of_property_read_u32_array(np, "arm,filter-ranges",
+ filter, ARRAY_SIZE(filter));
+ if (filter[0] && filter[1]) {
+ writel_relaxed(ALIGN(filter[0] + filter[1], SZ_1M),
+ l2x0_base + L2X0_ADDR_FILTER_END);
+ writel_relaxed((filter[0] & ~(SZ_1M - 1)) | L2X0_ADDR_FILTER_EN,
+ l2x0_base + L2X0_ADDR_FILTER_START);
+ }
+}
+
+static const struct of_device_id l2x0_ids[] __initconst = {
+ { .compatible = "arm,pl310-cache", .data = pl310_of_setup },
+ { .compatible = "arm,l220-cache", .data = l2x0_of_setup },
+ { .compatible = "arm,l210-cache", .data = l2x0_of_setup },
+ {}
+};
+
+int __init l2x0_of_init(__u32 aux_val, __u32 aux_mask)
+{
+ struct device_node *np;
+ void (*l2_setup)(const struct device_node *np,
+ __u32 *aux_val, __u32 *aux_mask);
+
+ np = of_find_matching_node(NULL, l2x0_ids);
+ if (!np)
+ return -ENODEV;
+ l2x0_base = of_iomap(np, 0);
+ if (!l2x0_base)
+ return -ENOMEM;
+
+ /* L2 configuration can only be changed if the cache is disabled */
+ if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+ l2_setup = of_match_node(l2x0_ids, np)->data;
+ if (l2_setup)
+ l2_setup(np, &aux_val, &aux_mask);
+ }
+ l2x0_init(l2x0_base, aux_val, aux_mask);
+ return 0;
+}
+#endif
#include <linux/device.h>
#include <linux/dma-mapping.h>
#include <linux/highmem.h>
+#include <linux/slab.h>
#include <asm/memory.h>
#include <asm/highmem.h>
#include <asm/cacheflush.h>
#include <asm/tlbflush.h>
#include <asm/sizes.h>
+#include <asm/mach/arch.h>
#include "mm.h"
}
#ifdef CONFIG_MMU
-/* Sanity check size */
-#if (CONSISTENT_DMA_SIZE % SZ_2M)
-#error "CONSISTENT_DMA_SIZE must be multiple of 2MiB"
-#endif
-#define CONSISTENT_OFFSET(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PAGE_SHIFT)
-#define CONSISTENT_PTE_INDEX(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PGDIR_SHIFT)
-#define NUM_CONSISTENT_PTES (CONSISTENT_DMA_SIZE >> PGDIR_SHIFT)
+#define CONSISTENT_OFFSET(x) (((unsigned long)(x) - consistent_base) >> PAGE_SHIFT)
+#define CONSISTENT_PTE_INDEX(x) (((unsigned long)(x) - consistent_base) >> PMD_SHIFT)
/*
* These are the page tables (2MB each) covering uncached, DMA consistent allocations
*/
-static pte_t *consistent_pte[NUM_CONSISTENT_PTES];
+static pte_t **consistent_pte;
+
+#define DEFAULT_CONSISTENT_DMA_SIZE SZ_2M
+
+unsigned long consistent_base = CONSISTENT_END - DEFAULT_CONSISTENT_DMA_SIZE;
+
+void __init init_consistent_dma_size(unsigned long size)
+{
+ unsigned long base = CONSISTENT_END - ALIGN(size, SZ_2M);
+
+ BUG_ON(consistent_pte); /* Check we're called before DMA region init */
+ BUG_ON(base < VMALLOC_END);
+
+ /* Grow region to accommodate specified size */
+ if (base < consistent_base)
+ consistent_base = base;
+}
#include "vmregion.h"
static struct arm_vmregion_head consistent_head = {
.vm_lock = __SPIN_LOCK_UNLOCKED(&consistent_head.vm_lock),
.vm_list = LIST_HEAD_INIT(consistent_head.vm_list),
- .vm_start = CONSISTENT_BASE,
.vm_end = CONSISTENT_END,
};
pmd_t *pmd;
pte_t *pte;
int i = 0;
- u32 base = CONSISTENT_BASE;
+ unsigned long base = consistent_base;
+ unsigned long num_ptes = (CONSISTENT_END - base) >> PGDIR_SHIFT;
+
+ consistent_pte = kmalloc(num_ptes * sizeof(pte_t), GFP_KERNEL);
+ if (!consistent_pte) {
+ pr_err("%s: no memory\n", __func__);
+ return -ENOMEM;
+ }
+
+ pr_debug("DMA memory: 0x%08lx - 0x%08lx:\n", base, CONSISTENT_END);
+ consistent_head.vm_start = base;
do {
pgd = pgd_offset(&init_mm, base);
}
consistent_pte[i++] = pte;
- base += (1 << PGDIR_SHIFT);
+ base += PMD_SIZE;
} while (base < CONSISTENT_END);
return ret;
size_t align;
int bit;
- if (!consistent_pte[0]) {
+ if (!consistent_pte) {
printk(KERN_ERR "%s: not initialised\n", __func__);
dump_stack();
return NULL;
" ITCM : 0x%08lx - 0x%08lx (%4ld kB)\n"
#endif
" fixmap : 0x%08lx - 0x%08lx (%4ld kB)\n"
-#ifdef CONFIG_MMU
- " DMA : 0x%08lx - 0x%08lx (%4ld MB)\n"
-#endif
" vmalloc : 0x%08lx - 0x%08lx (%4ld MB)\n"
" lowmem : 0x%08lx - 0x%08lx (%4ld MB)\n"
#ifdef CONFIG_HIGHMEM
MLK(ITCM_OFFSET, (unsigned long) itcm_end),
#endif
MLK(FIXADDR_START, FIXADDR_TOP),
-#ifdef CONFIG_MMU
- MLM(CONSISTENT_BASE, CONSISTENT_END),
-#endif
MLM(VMALLOC_START, VMALLOC_END),
MLM(PAGE_OFFSET, (unsigned long)high_memory),
#ifdef CONFIG_HIGHMEM
* be detected at build time already.
*/
#ifdef CONFIG_MMU
- BUILD_BUG_ON(VMALLOC_END > CONSISTENT_BASE);
- BUG_ON(VMALLOC_END > CONSISTENT_BASE);
-
BUILD_BUG_ON(TASK_SIZE > MODULES_VADDR);
BUG_ON(TASK_SIZE > MODULES_VADDR);
#endif
/*
* Clear out all the mappings below the kernel image.
*/
- for (addr = 0; addr < MODULES_VADDR; addr += PGDIR_SIZE)
+ for (addr = 0; addr < MODULES_VADDR; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
#ifdef CONFIG_XIP_KERNEL
/* The XIP kernel is mapped in the module area -- skip over it */
- addr = ((unsigned long)_etext + PGDIR_SIZE - 1) & PGDIR_MASK;
+ addr = ((unsigned long)_etext + PMD_SIZE - 1) & PMD_MASK;
#endif
- for ( ; addr < PAGE_OFFSET; addr += PGDIR_SIZE)
+ for ( ; addr < PAGE_OFFSET; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
/*
* memory bank, up to the end of the vmalloc region.
*/
for (addr = __phys_to_virt(end);
- addr < VMALLOC_END; addr += PGDIR_SIZE)
+ addr < VMALLOC_END; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
}
+#define SWAPPER_PG_DIR_SIZE (PTRS_PER_PGD * sizeof(pgd_t))
+
/*
* Reserve the special regions of memory
*/
* Reserve the page tables. These are already in use,
* and can only be in node 0.
*/
- memblock_reserve(__pa(swapper_pg_dir), PTRS_PER_PGD * sizeof(pgd_t));
+ memblock_reserve(__pa(swapper_pg_dir), SWAPPER_PG_DIR_SIZE);
#ifdef CONFIG_SA1111
/*
*/
vectors_page = early_alloc(PAGE_SIZE);
- for (addr = VMALLOC_END; addr; addr += PGDIR_SIZE)
+ for (addr = VMALLOC_END; addr; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
/*
#include <linux/spinlock.h>
#include <mach/hardware.h>
-#include <asm-generic/gpio.h>
/* There's a off-by-one betweem the gpio bank number and the gpiochip */
/* range e.g. GPIO_1_5 is gpio 5 under linux */
#define IMX_GPIO_NR(bank, nr) (((bank) - 1) * 32 + (nr))
-/* use gpiolib dispatchers */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-
#define gpio_to_irq(gpio) (MXC_GPIO_IRQ_START + (gpio))
#define irq_to_gpio(irq) ((irq) - MXC_GPIO_IRQ_START)
# endif
#endif
-#if defined(CONFIG_MX3_VIDEO)
-/*
- * Increase size of DMA-consistent memory region.
- * This is required for mx3 camera driver to capture at least two QXGA frames.
- */
-#define CONSISTENT_DMA_SIZE SZ_8M
-
-#elif defined(CONFIG_MX1_VIDEO) || defined(CONFIG_VIDEO_MX2_HOSTSUPPORT)
-/*
- * Increase size of DMA-consistent memory region.
- * This is required for i.MX camera driver to capture at least four VGA frames.
- */
-#define CONSISTENT_DMA_SIZE SZ_4M
-#endif /* CONFIG_MX1_VIDEO || CONFIG_VIDEO_MX2_HOSTSUPPORT */
-
#endif /* __ASM_ARCH_MXC_MEMORY_H__ */
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#ifndef __ASM_PLAT_GPIO_H
-#define __ASM_PLAT_GPIO_H
-#include <asm-generic/gpio.h>
-
-/*
- * These currently cause a function call to happen, they may be optimized
- * if needed by adding cpu-specific defines to identify blocks
- * (see mach-pxa/include/mach/gpio.h as an example using GPLR etc)
- */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
+#ifndef __PLAT_NOMADIK_GPIO
+#define __PLAT_NOMADIK_GPIO
/*
* "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
bool supports_sleepmode;
};
-#endif /* __ASM_PLAT_GPIO_H */
+#endif /* __PLAT_NOMADIK_GPIO */
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <plat/board.h>
-#include <mach/gpio.h>
/* Many OMAP development platforms reuse the same "debug board"; these
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <plat/fpga.h>
-#include <mach/gpio.h>
/* Many OMAP development platforms reuse the same "debug board"; these
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
#include <plat/menelaus.h>
#include <plat/mcbsp.h>
#include <plat/omap44xx.h>
#include <linux/errno.h>
#include <asm-generic/gpio.h>
-static inline int gpio_get_value(unsigned gpio)
-{
- return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- __gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
- return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
- return __gpio_to_irq(gpio);
-}
-
static inline int irq_to_gpio(unsigned irq)
{
int tmp;
void __iomem *omap_ioremap(unsigned long phys, size_t size, unsigned int type);
void omap_iounmap(volatile void __iomem *addr);
+extern void __init omap_init_consistent_dma_size(void);
+
#endif
#endif
#endif /* CONFIG_ARCH_OMAP15XX */
-/* Override the ARM default */
-#ifdef CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE
-
-#if (CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE == 0)
-#undef CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE
-#define CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE 2
-#endif
-
-#define CONSISTENT_DMA_SIZE \
- (((CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE + 1) & ~1) * 1024 * 1024)
-
-#endif
-
#endif
#include <linux/module.h>
#include <linux/io.h>
#include <linux/mm.h>
+#include <linux/dma-mapping.h>
#include <plat/omap7xx.h>
#include <plat/omap1510.h>
__iounmap(addr);
}
EXPORT_SYMBOL(omap_iounmap);
+
+void __init omap_init_consistent_dma_size(void)
+{
+#ifdef CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE
+ init_consistent_dma_size(CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE << 20);
+#endif
+}
#define __PLAT_GPIO_H
#include <linux/init.h>
-#include <asm-generic/gpio.h>
-
-/*
- * GENERIC_GPIO primitives.
- */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
+#include <linux/types.h>
/*
* Orion-specific GPIO API extensions.
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/syscore_ops.h>
#include <linux/slab.h>
-#include <mach/gpio.h>
-
int pxa_last_gpio;
struct pxa_gpio_chip {
#ifndef __PLAT_GPIO_H
#define __PLAT_GPIO_H
+#define __ARM_GPIOLIB_COMPLEX
+
struct irq_data;
/*
-/*
- * arch/arm/plat-spear/include/plat/gpio.h
- *
- * GPIO macros for SPEAr platform
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_GPIO_H
-#define __PLAT_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-#define gpio_to_irq __gpio_to_irq
-
-#endif /* __PLAT_GPIO_H */
+/* empty */
#endif /* !CONFIG_HIBERNATE_CALLBACKS */
+#ifdef CONFIG_PM_RUNTIME
+/*
+ * Hooks to provide runtime PM of the pclk (bus clock). It is safe to
+ * enable/disable the bus clock at runtime PM suspend/resume as this
+ * does not result in loss of context. However, disabling vcore power
+ * would do, so we leave that to the driver.
+ */
+static int amba_pm_runtime_suspend(struct device *dev)
+{
+ struct amba_device *pcdev = to_amba_device(dev);
+ int ret = pm_generic_runtime_suspend(dev);
+
+ if (ret == 0 && dev->driver)
+ clk_disable(pcdev->pclk);
+
+ return ret;
+}
+
+static int amba_pm_runtime_resume(struct device *dev)
+{
+ struct amba_device *pcdev = to_amba_device(dev);
+ int ret;
+
+ if (dev->driver) {
+ ret = clk_enable(pcdev->pclk);
+ /* Failure is probably fatal to the system, but... */
+ if (ret)
+ return ret;
+ }
+
+ return pm_generic_runtime_resume(dev);
+}
+#endif
+
#ifdef CONFIG_PM
static const struct dev_pm_ops amba_pm = {
.poweroff_noirq = amba_pm_poweroff_noirq,
.restore_noirq = amba_pm_restore_noirq,
SET_RUNTIME_PM_OPS(
- pm_generic_runtime_suspend,
- pm_generic_runtime_resume,
+ amba_pm_runtime_suspend,
+ amba_pm_runtime_resume,
pm_generic_runtime_idle
)
};
if (ret)
break;
+ pm_runtime_get_noresume(dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+
ret = pcdrv->probe(pcdev, id);
if (ret == 0)
break;
+ pm_runtime_disable(dev);
+ pm_runtime_set_suspended(dev);
+ pm_runtime_put_noidle(dev);
+
amba_put_disable_pclk(pcdev);
amba_put_disable_vcore(pcdev);
} while (0);
{
struct amba_device *pcdev = to_amba_device(dev);
struct amba_driver *drv = to_amba_driver(dev->driver);
- int ret = drv->remove(pcdev);
+ int ret;
+
+ pm_runtime_get_sync(dev);
+ ret = drv->remove(pcdev);
+ pm_runtime_put_noidle(dev);
+
+ /* Undo the runtime PM settings in amba_probe() */
+ pm_runtime_disable(dev);
+ pm_runtime_set_suspended(dev);
+ pm_runtime_put_noidle(dev);
amba_put_disable_pclk(pcdev);
amba_put_disable_vcore(pcdev);
#include <mach/at91sam9_smc.h>
#include <mach/board.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#define DRV_NAME "pata_at91"
#define DRV_VERSION "0.3"
obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o
obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
+obj-$(CONFIG_ARCH_DAVINCI) += gpio-davinci.o
obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o
obj-$(CONFIG_GPIO_EXYNOS4) += gpio-exynos4.o
obj-$(CONFIG_GPIO_IT8761E) += gpio-it8761e.o
obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o
+obj-$(CONFIG_MACH_KS8695) += gpio-ks8695.o
obj-$(CONFIG_GPIO_LANGWELL) += gpio-langwell.o
+obj-$(CONFIG_ARCH_LPC32XX) += gpio-lpc32xx.o
obj-$(CONFIG_GPIO_MAX730X) += gpio-max730x.o
obj-$(CONFIG_GPIO_MAX7300) += gpio-max7300.o
obj-$(CONFIG_GPIO_MAX7301) += gpio-max7301.o
obj-$(CONFIG_GPIO_PLAT_SAMSUNG) += gpio-plat-samsung.o
obj-$(CONFIG_GPIO_S5PC100) += gpio-s5pc100.o
obj-$(CONFIG_GPIO_S5PV210) += gpio-s5pv210.o
-
+obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o
obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o
obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o
obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o
obj-$(CONFIG_ARCH_TEGRA) += gpio-tegra.o
obj-$(CONFIG_GPIO_TIMBERDALE) += gpio-timberdale.o
+obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o
obj-$(CONFIG_GPIO_TPS65910) += gpio-tps65910.o
obj-$(CONFIG_GPIO_TPS65912) += gpio-tps65912.o
obj-$(CONFIG_GPIO_TWL4030) += gpio-twl4030.o
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
-
+#include <linux/gpio.h>
#include <linux/errno.h>
#include <linux/kernel.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
-#include <mach/gpio.h>
-
#include <asm/mach/irq.h>
struct davinci_gpio_regs {
return 0;
}
+/*
+ * Map GPIO A0..A7 (0..7) to irq 64..71,
+ * B0..B7 (7..15) to irq 72..79, and
+ * F0..F7 (16..24) to irq 80..87.
+ */
+static int ep93xx_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ int gpio = chip->base + offset;
+
+ if (gpio > EP93XX_GPIO_LINE_MAX_IRQ)
+ return -EINVAL;
+
+ return 64 + gpio;
+}
+
static int ep93xx_gpio_add_bank(struct bgpio_chip *bgc, struct device *dev,
void __iomem *mmio_base, struct ep93xx_gpio_bank *bank)
{
bgc->gc.label = bank->label;
bgc->gc.base = bank->base;
- if (bank->has_debounce)
+ if (bank->has_debounce) {
bgc->gc.set_debounce = ep93xx_gpio_set_debounce;
+ bgc->gc.to_irq = ep93xx_gpio_to_irq;
+ }
return gpiochip_add(&bgc->gc);
}
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-
+#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/mm.h>
#include <linux/init.h>
#include <asm/mach/irq.h>
#include <mach/regs-gpio.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
/*
* Configure a GPIO line for either GPIO function, or its internal
#include <mach/hardware.h>
#include <mach/platform.h>
-#include "common.h"
+#include <mach/gpio-lpc32xx.h>
#define LPC32XX_GPIO_P3_INP_STATE _GPREG(0x000)
#define LPC32XX_GPIO_P3_OUTP_SET _GPREG(0x004)
#include <asm/mach/irq.h>
#include <plat/pincfg.h>
+#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
/*
* The GPIO module in the Nomadik family of Systems-on-Chip is an
#include <mach/hardware.h>
#include <asm/irq.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <asm/mach/irq.h>
struct gpio_bank {
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-
+#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/module.h>
-#include <asm/gpio.h>
#include <mach/hardware.h>
-#include "generic.h"
static int sa1100_gpio_get(struct gpio_chip *chip, unsigned offset)
{
return 0;
}
-
+static int tegra_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ return TEGRA_GPIO_TO_IRQ(offset);
+}
static struct gpio_chip tegra_gpio_chip = {
.label = "tegra-gpio",
.get = tegra_gpio_get,
.direction_output = tegra_gpio_direction_output,
.set = tegra_gpio_set,
+ .to_irq = tegra_gpio_to_irq,
.base = 0,
.ngpio = TEGRA_NR_GPIOS,
};
static int __init tegra_gpio_init(void)
{
struct tegra_gpio_bank *bank;
+ int gpio;
int i;
int j;
gpiochip_add(&tegra_gpio_chip);
- for (i = INT_GPIO_BASE; i < (INT_GPIO_BASE + TEGRA_NR_GPIOS); i++) {
- bank = &tegra_gpio_banks[GPIO_BANK(irq_to_gpio(i))];
+ for (gpio = 0; gpio < TEGRA_NR_GPIOS; gpio++) {
+ int irq = TEGRA_GPIO_TO_IRQ(gpio);
+ /* No validity check; all Tegra GPIOs are valid IRQs */
+
+ bank = &tegra_gpio_banks[GPIO_BANK(gpio)];
- irq_set_lockdep_class(i, &gpio_lock_class);
- irq_set_chip_data(i, bank);
- irq_set_chip_and_handler(i, &tegra_gpio_irq_chip,
+ irq_set_lockdep_class(irq, &gpio_lock_class);
+ irq_set_chip_data(irq, bank);
+ irq_set_chip_and_handler(irq, &tegra_gpio_irq_chip,
handle_simple_irq);
- set_irq_flags(i, IRQF_VALID);
+ set_irq_flags(irq, IRQF_VALID);
}
for (i = 0; i < ARRAY_SIZE(tegra_gpio_banks); i++) {
#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <mach/gpio-u300.h>
/* Reference to GPIO block clock */
static struct clk *clk;
#include <linux/slab.h>
#include <mach/hardware.h> /* Pick up IXP2000-specific bits */
-#include <mach/gpio.h>
+#include <mach/gpio-ixp2000.h>
static inline int ixp2000_scl_pin(void *data)
{
#include <linux/platform_device.h>
#include <mach/board.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <mach/at91sam9_smc.h>
#define DRV_NAME "at91_ide"
#include <linux/mutex.h>
#include <linux/errno.h>
#include <linux/slab.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/keypad.h>
#include <plat/menelaus.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/menelaus.h>
#define DRIVER_NAME "menelaus"
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/amba/mmci.h>
+#include <linux/pm_runtime.h>
#include <asm/div64.h>
#include <asm/io.h>
* back into the driver...
*/
spin_unlock(&host->lock);
+ pm_runtime_put(mmc_dev(host->mmc));
mmc_request_done(host->mmc, mrq);
spin_lock(&host->lock);
}
return;
}
+ pm_runtime_get_sync(mmc_dev(mmc));
+
spin_lock_irqsave(&host->lock, flags);
host->mrq = mrq;
mmci_dma_setup(host);
+ pm_runtime_put(&dev->dev);
+
mmc_add_host(mmc);
return 0;
if (mmc) {
struct mmci_host *host = mmc_priv(mmc);
+ /*
+ * Undo pm_runtime_put() in probe. We use the _sync
+ * version here so that we can access the primecell.
+ */
+ pm_runtime_get_sync(&dev->dev);
+
mmc_remove_host(mmc);
writel(0, host->base + MMCIMASK0);
#include <plat/board.h>
#include <plat/mmc.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/dma.h>
#include <plat/mux.h>
#include <plat/fpga.h>
#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <mach/sdhci.h>
#include "sdhci-pltfm.h"
#include <asm/io.h>
#include <mach/hardware.h>
#include <asm/sizes.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/board-ams-delta.h>
/*
#include <asm/mach/flash.h>
#include <plat/gpmc.h>
#include <plat/onenand.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/dma.h>
#include <asm/mach-types.h>
#include <mach/at91rm9200_emac.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <mach/board.h>
#include "at91_ether.h"
#include <asm/mach-types.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <mach/vpac270.h>
#include "soc_common.h"
#include <asm/io.h>
#include <mach/board.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <mach/cpu.h>
/* SPI register offsets */
if (msg->complete)
msg->complete(msg->context);
/* This message is completed, so let's turn off the clocks & power */
- clk_disable(pl022->clk);
- amba_pclk_disable(pl022->adev);
- amba_vcore_disable(pl022->adev);
pm_runtime_put(&pl022->adev->dev);
}
* (poll/interrupt/DMA)
*/
pm_runtime_get_sync(&pl022->adev->dev);
- amba_vcore_enable(pl022->adev);
- amba_pclk_enable(pl022->adev);
- clk_enable(pl022->clk);
restore_state(pl022);
flush(pl022);
}
printk(KERN_INFO "pl022: mapped registers from 0x%08x to %p\n",
adev->res.start, pl022->virtbase);
- pm_runtime_enable(dev);
- pm_runtime_resume(dev);
pl022->clk = clk_get(&adev->dev, NULL);
if (IS_ERR(pl022->clk)) {
dev_err(&adev->dev, "could not retrieve SSP/SPI bus clock\n");
goto err_no_clk;
}
-
/* Disable SSP */
writew((readw(SSP_CR1(pl022->virtbase)) & (~SSP_CR1_MASK_SSE)),
SSP_CR1(pl022->virtbase));
goto err_spi_register;
}
dev_dbg(dev, "probe succeeded\n");
- /*
- * Disable the silicon block pclk and any voltage domain and just
- * power it up and clock it when it's needed
- */
- amba_pclk_disable(adev);
- amba_vcore_disable(adev);
+
+ /* let runtime pm put suspend */
+ pm_runtime_put(dev);
return 0;
err_spi_register:
destroy_queue(pl022);
pl022_dma_remove(pl022);
free_irq(adev->irq[0], pl022);
- pm_runtime_disable(&adev->dev);
err_no_irq:
clk_put(pl022->clk);
err_no_clk:
if (!pl022)
return 0;
+ /*
+ * undo pm_runtime_put() in probe. I assume that we're not
+ * accessing the primecell here.
+ */
+ pm_runtime_get_noresume(&adev->dev);
+
/* Remove the queue */
if (destroy_queue(pl022) != 0)
dev_err(&adev->dev, "queue remove failed\n");
return 0;
}
-#ifdef CONFIG_PM
-static int pl022_suspend(struct amba_device *adev, pm_message_t state)
+#ifdef CONFIG_SUSPEND
+static int pl011_suspend(struct device *dev)
{
- struct pl022 *pl022 = amba_get_drvdata(adev);
+ struct pl022 *pl022 = dev_get_drvdata(dev);
int status = 0;
status = stop_queue(pl022);
return status;
}
- amba_vcore_enable(adev);
- amba_pclk_enable(adev);
+ amba_vcore_enable(pl022->adev);
+ amba_pclk_enable(pl022->adev);
load_ssp_default_config(pl022);
- amba_pclk_disable(adev);
- amba_vcore_disable(adev);
+ amba_pclk_disable(pl022->adev);
+ amba_vcore_disable(pl022->adev);
dev_dbg(&adev->dev, "suspended\n");
return 0;
}
-static int pl022_resume(struct amba_device *adev)
+static int pl022_resume(struct device *dev)
{
- struct pl022 *pl022 = amba_get_drvdata(adev);
+ struct pl022 *pl022 = dev_get_drvdata(dev);
int status = 0;
/* Start the queue running */
status = start_queue(pl022);
if (status)
- dev_err(&adev->dev, "problem starting queue (%d)\n", status);
+ dev_err(dev, "problem starting queue (%d)\n", status);
else
- dev_dbg(&adev->dev, "resumed\n");
+ dev_dbg(dev, "resumed\n");
return status;
}
-#else
-#define pl022_suspend NULL
-#define pl022_resume NULL
#endif /* CONFIG_PM */
+#ifdef CONFIG_PM_RUNTIME
+static int pl022_runtime_suspend(struct device *dev)
+{
+ struct pl022 *pl022 = dev_get_drvdata(dev);
+
+ clk_disable(pl022->clk);
+ amba_vcore_disable(pl022->adev);
+
+ return 0;
+}
+
+static int pl022_runtime_resume(struct device *dev)
+{
+ struct pl022 *pl022 = dev_get_drvdata(dev);
+
+ amba_vcore_enable(pl022->adev);
+ clk_enable(pl022->clk);
+
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops pl022_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pl022_suspend, pl022_resume)
+ SET_RUNTIME_PM_OPS(pl022_runtime_suspend, pl022_runtime_resume, NULL)
+};
+
static struct vendor_data vendor_arm = {
.fifodepth = 8,
.max_bpw = 16,
static struct amba_driver pl022_driver = {
.drv = {
.name = "ssp-pl022",
+ .pm = &pl022_dev_pm_ops,
},
.id_table = pl022_ids,
.probe = pl022_probe,
.remove = __devexit_p(pl022_remove),
- .suspend = pl022_suspend,
- .resume = pl022_resume,
};
#ifdef CONFIG_ARM
#include <mach/cpu.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#endif
#define PDC_BUFFER_SIZE 512
#include <mach/platform.h>
#include <mach/irqs.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#define USB_CTRL IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64)
#include <mach/hardware.h>
#include <mach/memory.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <mach/cputype.h>
#include <asm/mach-types.h>
#include <mach/board.h>
#include <mach/cpu.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <video/atmel_lcdc.h>
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include "omapfb.h"
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include "omapfb.h"
#define MODULE_NAME "omapfb-lcd_h3"
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include "omapfb.h"
#define MODULE_NAME "omapfb-lcd_h3"
#include <linux/delay.h>
#include <linux/i2c/twl.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/mux.h>
#include <asm/mach-types.h>
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/mux.h>
#include "omapfb.h"
#include <linux/platform_device.h>
#include <linux/i2c/twl.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include <plat/mux.h>
#include <asm/mach-types.h>
#include <linux/module.h>
#include <linux/io.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include "omapfb.h"
static int palmtt_panel_init(struct lcd_panel *panel,
#include <linux/clk.h>
#include <linux/gfp.h>
#include <asm/uaccess.h>
-#include <mach/gpio.h>
+#include <asm/gpio.h>
#include "sdum.h"
#include "fbcommon.h"
projects / karo-tx-linux.git / commitdiff