F: arch/arm/configs/mvebu_*_defconfig
ARM/Marvell Berlin SoC support
+M: Jisheng Zhang <jszhang@marvell.com>
M: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
+ cap-sd-highspeed;
cap-mmc-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ /* All direction control is used */
+ st,sig-dir-cmd;
+ st,sig-dir-dat0;
+ st,sig-dir-dat2;
+ st,sig-dir-dat31;
+ st,sig-pin-fbclk;
+ full-pwr-cycle;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdi0_default_mode>;
pinctrl-1 = <&sdi0_sleep_mode>;
- cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; // 218
+ /* GPIO218 MMC_CD */
+ cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;
status = "okay";
};
/* VMMCI level-shifter enable */
snowball_cfg3 {
pins = "GPIO217_AH12";
- ste,config = <&gpio_out_lo>;
+ ste,config = <&gpio_out_hi>;
};
/* VMMCI level-shifter voltage select */
snowball_cfg4 {
CONFIG_PWM_TEGRA=y
CONFIG_PWM_VT8500=y
CONFIG_PHY_HIX5HD2_SATA=y
+CONFIG_E1000E=y
CONFIG_PWM_STI=y
CONFIG_PWM_BCM2835=y
CONFIG_PWM_BRCMSTB=m
select CACHE_L2X0
select ARM_CPU_SUSPEND
select MACH_MVEBU_ANY
+ select MVEBU_CLK_COREDIV
config MACH_ARMADA_370
bool "Marvell Armada 370 boards"
select CPU_PJ4B
select MACH_MVEBU_V7
select PINCTRL_ARMADA_370
- select MVEBU_CLK_COREDIV
help
Say 'Y' here if you want your kernel to support boards based
on the Marvell Armada 370 SoC with device tree.
select HAVE_SMP
select MACH_MVEBU_V7
select PINCTRL_ARMADA_375
- select MVEBU_CLK_COREDIV
help
Say 'Y' here if you want your kernel to support boards based
on the Marvell Armada 375 SoC with device tree.
select HAVE_SMP
select MACH_MVEBU_V7
select PINCTRL_ARMADA_38X
- select MVEBU_CLK_COREDIV
help
Say 'Y' here if you want your kernel to support boards based
on the Marvell Armada 380/385 SoC with device tree.
#address-cells = <0x1>;
#size-cells = <0x0>;
cell-index = <1>;
- clocks = <&cpm_syscon0 0 3>;
+ clocks = <&cpm_syscon0 1 21>;
status = "disabled";
};
config QCOM_EBI2
bool "Qualcomm External Bus Interface 2 (EBI2)"
depends on HAS_IOMEM
+ depends on ARCH_QCOM || COMPILE_TEST
help
Say y here to enable support for the Qualcomm External Bus
Interface 2, which can be used to connect things like NAND Flash,