Format: { 0 | 1 }
See arch/parisc/kernel/pdc_chassis.c
+ percpu_alloc= [X86] Select which percpu first chunk allocator to use.
+ Allowed values are one of "lpage", "embed" and "4k".
+ See comments in arch/x86/kernel/setup_percpu.c for
+ details on each allocator. This parameter is primarily
+ for debugging and performance comparison.
+
pf. [PARIDE]
See Documentation/blockdev/paride.txt.
tp720= [HW,PS2]
- trace_buf_size=nn[KMG] [ftrace] will set tracing buffer size.
+ trace_buf_size=nn[KMG]
+ [FTRACE] will set tracing buffer size.
trix= [HW,OSS] MediaTrix AudioTrix Pro
Format:
--- /dev/null
+Kernel driver lp3944
+====================
+
+ * National Semiconductor LP3944 Fun-light Chip
+ Prefix: 'lp3944'
+ Addresses scanned: None (see the Notes section below)
+ Datasheet: Publicly available at the National Semiconductor website
+ http://www.national.com/pf/LP/LP3944.html
+
+Authors:
+ Antonio Ospite <ospite@studenti.unina.it>
+
+
+Description
+-----------
+The LP3944 is a helper chip that can drive up to 8 leds, with two programmable
+DIM modes; it could even be used as a gpio expander but this driver assumes it
+is used as a led controller.
+
+The DIM modes are used to set _blink_ patterns for leds, the pattern is
+specified supplying two parameters:
+ - period: from 0s to 1.6s
+ - duty cycle: percentage of the period the led is on, from 0 to 100
+
+Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
+See the datasheet for details.
+
+LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
+leds, the camera flash light and the lcds power.
+
+
+Notes
+-----
+The chip is used mainly in embedded contexts, so this driver expects it is
+registered using the i2c_board_info mechanism.
+
+To register the chip at address 0x60 on adapter 0, set the platform data
+according to include/linux/leds-lp3944.h, set the i2c board info:
+
+ static struct i2c_board_info __initdata a910_i2c_board_info[] = {
+ {
+ I2C_BOARD_INFO("lp3944", 0x60),
+ .platform_data = &a910_lp3944_leds,
+ },
+ };
+
+and register it in the platform init function
+
+ i2c_register_board_info(0, a910_i2c_board_info,
+ ARRAY_SIZE(a910_i2c_board_info));
defined; this list will expand as more and more SOC-containing
platforms are moved over to use the flattened-device-tree model.
- a) PHY nodes
-
- Required properties:
-
- - device_type : Should be "ethernet-phy"
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - reg : The ID number for the phy, usually a small integer
- - linux,phandle : phandle for this node; likely referenced by an
- ethernet controller node.
-
-
- Example:
-
- ethernet-phy@0 {
- linux,phandle = <2452000>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <0>;
- device_type = "ethernet-phy";
- };
-
-
- b) Interrupt controllers
-
- Some SOC devices contain interrupt controllers that are different
- from the standard Open PIC specification. The SOC device nodes for
- these types of controllers should be specified just like a standard
- OpenPIC controller. Sense and level information should be encoded
- as specified in section 2) of this chapter for each device that
- specifies an interrupt.
-
- Example :
-
- pic@40000 {
- linux,phandle = <40000>;
- interrupt-controller;
- #address-cells = <0>;
- reg = <40000 40000>;
- compatible = "chrp,open-pic";
- device_type = "open-pic";
- };
-
- c) 4xx/Axon EMAC ethernet nodes
-
- The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
- the Axon bridge. To operate this needs to interact with a ths
- special McMAL DMA controller, and sometimes an RGMII or ZMII
- interface. In addition to the nodes and properties described
- below, the node for the OPB bus on which the EMAC sits must have a
- correct clock-frequency property.
-
- i) The EMAC node itself
-
- Required properties:
- - device_type : "network"
-
- - compatible : compatible list, contains 2 entries, first is
- "ibm,emac-CHIP" where CHIP is the host ASIC (440gx,
- 405gp, Axon) and second is either "ibm,emac" or
- "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon",
- "ibm,emac4"
- - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ>
- - interrupt-parent : optional, if needed for interrupt mapping
- - reg : <registers mapping>
- - local-mac-address : 6 bytes, MAC address
- - mal-device : phandle of the associated McMAL node
- - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated
- with this EMAC
- - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated
- with this EMAC
- - cell-index : 1 cell, hardware index of the EMAC cell on a given
- ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on
- each Axon chip)
- - max-frame-size : 1 cell, maximum frame size supported in bytes
- - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec
- operations.
- For Axon, 2048
- - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec
- operations.
- For Axon, 2048.
- - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate
- thresholds).
- For Axon, 0x00000010
- - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds)
- in bytes.
- For Axon, 0x00000100 (I think ...)
- - phy-mode : string, mode of operations of the PHY interface.
- Supported values are: "mii", "rmii", "smii", "rgmii",
- "tbi", "gmii", rtbi", "sgmii".
- For Axon on CAB, it is "rgmii"
- - mdio-device : 1 cell, required iff using shared MDIO registers
- (440EP). phandle of the EMAC to use to drive the
- MDIO lines for the PHY used by this EMAC.
- - zmii-device : 1 cell, required iff connected to a ZMII. phandle of
- the ZMII device node
- - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII
- channel or 0xffffffff if ZMII is only used for MDIO.
- - rgmii-device : 1 cell, required iff connected to an RGMII. phandle
- of the RGMII device node.
- For Axon: phandle of plb5/plb4/opb/rgmii
- - rgmii-channel : 1 cell, required iff connected to an RGMII. Which
- RGMII channel is used by this EMAC.
- Fox Axon: present, whatever value is appropriate for each
- EMAC, that is the content of the current (bogus) "phy-port"
- property.
-
- Optional properties:
- - phy-address : 1 cell, optional, MDIO address of the PHY. If absent,
- a search is performed.
- - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY
- for, used if phy-address is absent. bit 0x00000001 is
- MDIO address 0.
- For Axon it can be absent, though my current driver
- doesn't handle phy-address yet so for now, keep
- 0x00ffffff in it.
- - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
- operations (if absent the value is the same as
- rx-fifo-size). For Axon, either absent or 2048.
- - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec
- operations (if absent the value is the same as
- tx-fifo-size). For Axon, either absent or 2048.
- - tah-device : 1 cell, optional. If connected to a TAH engine for
- offload, phandle of the TAH device node.
- - tah-channel : 1 cell, optional. If appropriate, channel used on the
- TAH engine.
-
- Example:
-
- EMAC0: ethernet@40000800 {
- device_type = "network";
- compatible = "ibm,emac-440gp", "ibm,emac";
- interrupt-parent = <&UIC1>;
- interrupts = <1c 4 1d 4>;
- reg = <40000800 70>;
- local-mac-address = [00 04 AC E3 1B 1E];
- mal-device = <&MAL0>;
- mal-tx-channel = <0 1>;
- mal-rx-channel = <0>;
- cell-index = <0>;
- max-frame-size = <5dc>;
- rx-fifo-size = <1000>;
- tx-fifo-size = <800>;
- phy-mode = "rmii";
- phy-map = <00000001>;
- zmii-device = <&ZMII0>;
- zmii-channel = <0>;
- };
-
- ii) McMAL node
-
- Required properties:
- - device_type : "dma-controller"
- - compatible : compatible list, containing 2 entries, first is
- "ibm,mcmal-CHIP" where CHIP is the host ASIC (like
- emac) and the second is either "ibm,mcmal" or
- "ibm,mcmal2".
- For Axon, "ibm,mcmal-axon","ibm,mcmal2"
- - interrupts : <interrupt mapping for the MAL interrupts sources:
- 5 sources: tx_eob, rx_eob, serr, txde, rxde>.
- For Axon: This is _different_ from the current
- firmware. We use the "delayed" interrupts for txeob
- and rxeob. Thus we end up with mapping those 5 MPIC
- interrupts, all level positive sensitive: 10, 11, 32,
- 33, 34 (in decimal)
- - dcr-reg : < DCR registers range >
- - dcr-parent : if needed for dcr-reg
- - num-tx-chans : 1 cell, number of Tx channels
- - num-rx-chans : 1 cell, number of Rx channels
-
- iii) ZMII node
-
- Required properties:
- - compatible : compatible list, containing 2 entries, first is
- "ibm,zmii-CHIP" where CHIP is the host ASIC (like
- EMAC) and the second is "ibm,zmii".
- For Axon, there is no ZMII node.
- - reg : <registers mapping>
-
- iv) RGMII node
-
- Required properties:
- - compatible : compatible list, containing 2 entries, first is
- "ibm,rgmii-CHIP" where CHIP is the host ASIC (like
- EMAC) and the second is "ibm,rgmii".
- For Axon, "ibm,rgmii-axon","ibm,rgmii"
- - reg : <registers mapping>
- - revision : as provided by the RGMII new version register if
- available.
- For Axon: 0x0000012a
-
- d) Xilinx IP cores
-
- The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
- in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
- of standard device types (network, serial, etc.) and miscellaneous
- devices (gpio, LCD, spi, etc). Also, since these devices are
- implemented within the fpga fabric every instance of the device can be
- synthesised with different options that change the behaviour.
-
- Each IP-core has a set of parameters which the FPGA designer can use to
- control how the core is synthesized. Historically, the EDK tool would
- extract the device parameters relevant to device drivers and copy them
- into an 'xparameters.h' in the form of #define symbols. This tells the
- device drivers how the IP cores are configured, but it requres the kernel
- to be recompiled every time the FPGA bitstream is resynthesized.
-
- The new approach is to export the parameters into the device tree and
- generate a new device tree each time the FPGA bitstream changes. The
- parameters which used to be exported as #defines will now become
- properties of the device node. In general, device nodes for IP-cores
- will take the following form:
-
- (name): (generic-name)@(base-address) {
- compatible = "xlnx,(ip-core-name)-(HW_VER)"
- [, (list of compatible devices), ...];
- reg = <(baseaddr) (size)>;
- interrupt-parent = <&interrupt-controller-phandle>;
- interrupts = < ... >;
- xlnx,(parameter1) = "(string-value)";
- xlnx,(parameter2) = <(int-value)>;
- };
-
- (generic-name): an open firmware-style name that describes the
- generic class of device. Preferably, this is one word, such
- as 'serial' or 'ethernet'.
- (ip-core-name): the name of the ip block (given after the BEGIN
- directive in system.mhs). Should be in lowercase
- and all underscores '_' converted to dashes '-'.
- (name): is derived from the "PARAMETER INSTANCE" value.
- (parameter#): C_* parameters from system.mhs. The C_ prefix is
- dropped from the parameter name, the name is converted
- to lowercase and all underscore '_' characters are
- converted to dashes '-'.
- (baseaddr): the baseaddr parameter value (often named C_BASEADDR).
- (HW_VER): from the HW_VER parameter.
- (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1).
-
- Typically, the compatible list will include the exact IP core version
- followed by an older IP core version which implements the same
- interface or any other device with the same interface.
-
- 'reg', 'interrupt-parent' and 'interrupts' are all optional properties.
-
- For example, the following block from system.mhs:
-
- BEGIN opb_uartlite
- PARAMETER INSTANCE = opb_uartlite_0
- PARAMETER HW_VER = 1.00.b
- PARAMETER C_BAUDRATE = 115200
- PARAMETER C_DATA_BITS = 8
- PARAMETER C_ODD_PARITY = 0
- PARAMETER C_USE_PARITY = 0
- PARAMETER C_CLK_FREQ = 50000000
- PARAMETER C_BASEADDR = 0xEC100000
- PARAMETER C_HIGHADDR = 0xEC10FFFF
- BUS_INTERFACE SOPB = opb_7
- PORT OPB_Clk = CLK_50MHz
- PORT Interrupt = opb_uartlite_0_Interrupt
- PORT RX = opb_uartlite_0_RX
- PORT TX = opb_uartlite_0_TX
- PORT OPB_Rst = sys_bus_reset_0
- END
-
- becomes the following device tree node:
-
- opb_uartlite_0: serial@ec100000 {
- device_type = "serial";
- compatible = "xlnx,opb-uartlite-1.00.b";
- reg = <ec100000 10000>;
- interrupt-parent = <&opb_intc_0>;
- interrupts = <1 0>; // got this from the opb_intc parameters
- current-speed = <d#115200>; // standard serial device prop
- clock-frequency = <d#50000000>; // standard serial device prop
- xlnx,data-bits = <8>;
- xlnx,odd-parity = <0>;
- xlnx,use-parity = <0>;
- };
-
- Some IP cores actually implement 2 or more logical devices. In
- this case, the device should still describe the whole IP core with
- a single node and add a child node for each logical device. The
- ranges property can be used to translate from parent IP-core to the
- registers of each device. In addition, the parent node should be
- compatible with the bus type 'xlnx,compound', and should contain
- #address-cells and #size-cells, as with any other bus. (Note: this
- makes the assumption that both logical devices have the same bus
- binding. If this is not true, then separate nodes should be used
- for each logical device). The 'cell-index' property can be used to
- enumerate logical devices within an IP core. For example, the
- following is the system.mhs entry for the dual ps2 controller found
- on the ml403 reference design.
-
- BEGIN opb_ps2_dual_ref
- PARAMETER INSTANCE = opb_ps2_dual_ref_0
- PARAMETER HW_VER = 1.00.a
- PARAMETER C_BASEADDR = 0xA9000000
- PARAMETER C_HIGHADDR = 0xA9001FFF
- BUS_INTERFACE SOPB = opb_v20_0
- PORT Sys_Intr1 = ps2_1_intr
- PORT Sys_Intr2 = ps2_2_intr
- PORT Clkin1 = ps2_clk_rx_1
- PORT Clkin2 = ps2_clk_rx_2
- PORT Clkpd1 = ps2_clk_tx_1
- PORT Clkpd2 = ps2_clk_tx_2
- PORT Rx1 = ps2_d_rx_1
- PORT Rx2 = ps2_d_rx_2
- PORT Txpd1 = ps2_d_tx_1
- PORT Txpd2 = ps2_d_tx_2
- END
-
- It would result in the following device tree nodes:
-
- opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "xlnx,compound";
- ranges = <0 a9000000 2000>;
- // If this device had extra parameters, then they would
- // go here.
- ps2@0 {
- compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
- reg = <0 40>;
- interrupt-parent = <&opb_intc_0>;
- interrupts = <3 0>;
- cell-index = <0>;
- };
- ps2@1000 {
- compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
- reg = <1000 40>;
- interrupt-parent = <&opb_intc_0>;
- interrupts = <3 0>;
- cell-index = <0>;
- };
- };
-
- Also, the system.mhs file defines bus attachments from the processor
- to the devices. The device tree structure should reflect the bus
- attachments. Again an example; this system.mhs fragment:
-
- BEGIN ppc405_virtex4
- PARAMETER INSTANCE = ppc405_0
- PARAMETER HW_VER = 1.01.a
- BUS_INTERFACE DPLB = plb_v34_0
- BUS_INTERFACE IPLB = plb_v34_0
- END
-
- BEGIN opb_intc
- PARAMETER INSTANCE = opb_intc_0
- PARAMETER HW_VER = 1.00.c
- PARAMETER C_BASEADDR = 0xD1000FC0
- PARAMETER C_HIGHADDR = 0xD1000FDF
- BUS_INTERFACE SOPB = opb_v20_0
- END
-
- BEGIN opb_uart16550
- PARAMETER INSTANCE = opb_uart16550_0
- PARAMETER HW_VER = 1.00.d
- PARAMETER C_BASEADDR = 0xa0000000
- PARAMETER C_HIGHADDR = 0xa0001FFF
- BUS_INTERFACE SOPB = opb_v20_0
- END
-
- BEGIN plb_v34
- PARAMETER INSTANCE = plb_v34_0
- PARAMETER HW_VER = 1.02.a
- END
-
- BEGIN plb_bram_if_cntlr
- PARAMETER INSTANCE = plb_bram_if_cntlr_0
- PARAMETER HW_VER = 1.00.b
- PARAMETER C_BASEADDR = 0xFFFF0000
- PARAMETER C_HIGHADDR = 0xFFFFFFFF
- BUS_INTERFACE SPLB = plb_v34_0
- END
-
- BEGIN plb2opb_bridge
- PARAMETER INSTANCE = plb2opb_bridge_0
- PARAMETER HW_VER = 1.01.a
- PARAMETER C_RNG0_BASEADDR = 0x20000000
- PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF
- PARAMETER C_RNG1_BASEADDR = 0x60000000
- PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF
- PARAMETER C_RNG2_BASEADDR = 0x80000000
- PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF
- PARAMETER C_RNG3_BASEADDR = 0xC0000000
- PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF
- BUS_INTERFACE SPLB = plb_v34_0
- BUS_INTERFACE MOPB = opb_v20_0
- END
-
- Gives this device tree (some properties removed for clarity):
-
- plb@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "xlnx,plb-v34-1.02.a";
- device_type = "ibm,plb";
- ranges; // 1:1 translation
-
- plb_bram_if_cntrl_0: bram@ffff0000 {
- reg = <ffff0000 10000>;
- }
-
- opb@20000000 {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <20000000 20000000 20000000
- 60000000 60000000 20000000
- 80000000 80000000 40000000
- c0000000 c0000000 20000000>;
-
- opb_uart16550_0: serial@a0000000 {
- reg = <a00000000 2000>;
- };
-
- opb_intc_0: interrupt-controller@d1000fc0 {
- reg = <d1000fc0 20>;
- };
- };
- };
-
- That covers the general approach to binding xilinx IP cores into the
- device tree. The following are bindings for specific devices:
-
- i) Xilinx ML300 Framebuffer
-
- Simple framebuffer device from the ML300 reference design (also on the
- ML403 reference design as well as others).
-
- Optional properties:
- - resolution = <xres yres> : pixel resolution of framebuffer. Some
- implementations use a different resolution.
- Default is <d#640 d#480>
- - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory.
- Default is <d#1024 d#480>.
- - rotate-display (empty) : rotate display 180 degrees.
-
- ii) Xilinx SystemACE
-
- The Xilinx SystemACE device is used to program FPGAs from an FPGA
- bitstream stored on a CF card. It can also be used as a generic CF
- interface device.
-
- Optional properties:
- - 8-bit (empty) : Set this property for SystemACE in 8 bit mode
-
- iii) Xilinx EMAC and Xilinx TEMAC
-
- Xilinx Ethernet devices. In addition to general xilinx properties
- listed above, nodes for these devices should include a phy-handle
- property, and may include other common network device properties
- like local-mac-address.
-
- iv) Xilinx Uartlite
-
- Xilinx uartlite devices are simple fixed speed serial ports.
-
- Required properties:
- - current-speed : Baud rate of uartlite
-
- v) Xilinx hwicap
-
- Xilinx hwicap devices provide access to the configuration logic
- of the FPGA through the Internal Configuration Access Port
- (ICAP). The ICAP enables partial reconfiguration of the FPGA,
- readback of the configuration information, and some control over
- 'warm boots' of the FPGA fabric.
-
- Required properties:
- - xlnx,family : The family of the FPGA, necessary since the
- capabilities of the underlying ICAP hardware
- differ between different families. May be
- 'virtex2p', 'virtex4', or 'virtex5'.
-
- vi) Xilinx Uart 16550
-
- Xilinx UART 16550 devices are very similar to the NS16550 but with
- different register spacing and an offset from the base address.
-
- Required properties:
- - clock-frequency : Frequency of the clock input
- - reg-offset : A value of 3 is required
- - reg-shift : A value of 2 is required
-
- e) USB EHCI controllers
-
- Required properties:
- - compatible : should be "usb-ehci".
- - reg : should contain at least address and length of the standard EHCI
- register set for the device. Optional platform-dependent registers
- (debug-port or other) can be also specified here, but only after
- definition of standard EHCI registers.
- - interrupts : one EHCI interrupt should be described here.
- If device registers are implemented in big endian mode, the device
- node should have "big-endian-regs" property.
- If controller implementation operates with big endian descriptors,
- "big-endian-desc" property should be specified.
- If both big endian registers and descriptors are used by the controller
- implementation, "big-endian" property can be specified instead of having
- both "big-endian-regs" and "big-endian-desc".
-
- Example (Sequoia 440EPx):
- ehci@e0000300 {
- compatible = "ibm,usb-ehci-440epx", "usb-ehci";
- interrupt-parent = <&UIC0>;
- interrupts = <1a 4>;
- reg = <0 e0000300 90 0 e0000390 70>;
- big-endian;
- };
-
- f) MDIO on GPIOs
-
- Currently defined compatibles:
- - virtual,gpio-mdio
-
- MDC and MDIO lines connected to GPIO controllers are listed in the
- gpios property as described in section VIII.1 in the following order:
-
- MDC, MDIO.
-
- Example:
-
- mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qe_pio_a 11
- &qe_pio_c 6>;
- };
-
- g) SPI (Serial Peripheral Interface) busses
-
- SPI busses can be described with a node for the SPI master device
- and a set of child nodes for each SPI slave on the bus. For this
- discussion, it is assumed that the system's SPI controller is in
- SPI master mode. This binding does not describe SPI controllers
- in slave mode.
-
- The SPI master node requires the following properties:
- - #address-cells - number of cells required to define a chip select
- address on the SPI bus.
- - #size-cells - should be zero.
- - compatible - name of SPI bus controller following generic names
- recommended practice.
- No other properties are required in the SPI bus node. It is assumed
- that a driver for an SPI bus device will understand that it is an SPI bus.
- However, the binding does not attempt to define the specific method for
- assigning chip select numbers. Since SPI chip select configuration is
- flexible and non-standardized, it is left out of this binding with the
- assumption that board specific platform code will be used to manage
- chip selects. Individual drivers can define additional properties to
- support describing the chip select layout.
-
- SPI slave nodes must be children of the SPI master node and can
- contain the following properties.
- - reg - (required) chip select address of device.
- - compatible - (required) name of SPI device following generic names
- recommended practice
- - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
- - spi-cpol - (optional) Empty property indicating device requires
- inverse clock polarity (CPOL) mode
- - spi-cpha - (optional) Empty property indicating device requires
- shifted clock phase (CPHA) mode
- - spi-cs-high - (optional) Empty property indicating device requires
- chip select active high
-
- SPI example for an MPC5200 SPI bus:
- spi@f00 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
- reg = <0xf00 0x20>;
- interrupts = <2 13 0 2 14 0>;
- interrupt-parent = <&mpc5200_pic>;
-
- ethernet-switch@0 {
- compatible = "micrel,ks8995m";
- spi-max-frequency = <1000000>;
- reg = <0>;
- };
-
- codec@1 {
- compatible = "ti,tlv320aic26";
- spi-max-frequency = <100000>;
- reg = <1>;
- };
- };
-
-VII - Marvell Discovery mv64[345]6x System Controller chips
-===========================================================
-
-The Marvell mv64[345]60 series of system controller chips contain
-many of the peripherals needed to implement a complete computer
-system. In this section, we define device tree nodes to describe
-the system controller chip itself and each of the peripherals
-which it contains. Compatible string values for each node are
-prefixed with the string "marvell,", for Marvell Technology Group Ltd.
-
-1) The /system-controller node
-
- This node is used to represent the system-controller and must be
- present when the system uses a system controller chip. The top-level
- system-controller node contains information that is global to all
- devices within the system controller chip. The node name begins
- with "system-controller" followed by the unit address, which is
- the base address of the memory-mapped register set for the system
- controller chip.
-
- Required properties:
-
- - ranges : Describes the translation of system controller addresses
- for memory mapped registers.
- - clock-frequency: Contains the main clock frequency for the system
- controller chip.
- - reg : This property defines the address and size of the
- memory-mapped registers contained within the system controller
- chip. The address specified in the "reg" property should match
- the unit address of the system-controller node.
- - #address-cells : Address representation for system controller
- devices. This field represents the number of cells needed to
- represent the address of the memory-mapped registers of devices
- within the system controller chip.
- - #size-cells : Size representation for for the memory-mapped
- registers within the system controller chip.
- - #interrupt-cells : Defines the width of cells used to represent
- interrupts.
-
- Optional properties:
-
- - model : The specific model of the system controller chip. Such
- as, "mv64360", "mv64460", or "mv64560".
- - compatible : A string identifying the compatibility identifiers
- of the system controller chip.
-
- The system-controller node contains child nodes for each system
- controller device that the platform uses. Nodes should not be created
- for devices which exist on the system controller chip but are not used
-
- Example Marvell Discovery mv64360 system-controller node:
-
- system-controller@f1000000 { /* Marvell Discovery mv64360 */
- #address-cells = <1>;
- #size-cells = <1>;
- model = "mv64360"; /* Default */
- compatible = "marvell,mv64360";
- clock-frequency = <133333333>;
- reg = <0xf1000000 0x10000>;
- virtual-reg = <0xf1000000>;
- ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */
- 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */
- 0xa0000000 0xa0000000 0x4000000 /* User FLASH */
- 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */
- 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */
-
- [ child node definitions... ]
- }
-
-2) Child nodes of /system-controller
-
- a) Marvell Discovery MDIO bus
-
- The MDIO is a bus to which the PHY devices are connected. For each
- device that exists on this bus, a child node should be created. See
- the definition of the PHY node below for an example of how to define
- a PHY.
-
- Required properties:
- - #address-cells : Should be <1>
- - #size-cells : Should be <0>
- - device_type : Should be "mdio"
- - compatible : Should be "marvell,mv64360-mdio"
-
- Example:
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- device_type = "mdio";
- compatible = "marvell,mv64360-mdio";
-
- ethernet-phy@0 {
- ......
- };
- };
-
-
- b) Marvell Discovery ethernet controller
-
- The Discover ethernet controller is described with two levels
- of nodes. The first level describes an ethernet silicon block
- and the second level describes up to 3 ethernet nodes within
- that block. The reason for the multiple levels is that the
- registers for the node are interleaved within a single set
- of registers. The "ethernet-block" level describes the
- shared register set, and the "ethernet" nodes describe ethernet
- port-specific properties.
-
- Ethernet block node
-
- Required properties:
- - #address-cells : <1>
- - #size-cells : <0>
- - compatible : "marvell,mv64360-eth-block"
- - reg : Offset and length of the register set for this block
-
- Example Discovery Ethernet block node:
- ethernet-block@2000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "marvell,mv64360-eth-block";
- reg = <0x2000 0x2000>;
- ethernet@0 {
- .......
- };
- };
-
- Ethernet port node
-
- Required properties:
- - device_type : Should be "network".
- - compatible : Should be "marvell,mv64360-eth".
- - reg : Should be <0>, <1>, or <2>, according to which registers
- within the silicon block the device uses.
- - interrupts : <a> where a is the interrupt number for the port.
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
- - phy : the phandle for the PHY connected to this ethernet
- controller.
- - local-mac-address : 6 bytes, MAC address
-
- Example Discovery Ethernet port node:
- ethernet@0 {
- device_type = "network";
- compatible = "marvell,mv64360-eth";
- reg = <0>;
- interrupts = <32>;
- interrupt-parent = <&PIC>;
- phy = <&PHY0>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- };
-
-
-
- c) Marvell Discovery PHY nodes
-
- Required properties:
- - device_type : Should be "ethernet-phy"
- - interrupts : <a> where a is the interrupt number for this phy.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - reg : The ID number for the phy, usually a small integer
-
- Example Discovery PHY node:
- ethernet-phy@1 {
- device_type = "ethernet-phy";
- compatible = "broadcom,bcm5421";
- interrupts = <76>; /* GPP 12 */
- interrupt-parent = <&PIC>;
- reg = <1>;
- };
-
-
- d) Marvell Discovery SDMA nodes
-
- Represent DMA hardware associated with the MPSC (multiprotocol
- serial controllers).
-
- Required properties:
- - compatible : "marvell,mv64360-sdma"
- - reg : Offset and length of the register set for this device
- - interrupts : <a> where a is the interrupt number for the DMA
- device.
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
-
- Example Discovery SDMA node:
- sdma@4000 {
- compatible = "marvell,mv64360-sdma";
- reg = <0x4000 0xc18>;
- virtual-reg = <0xf1004000>;
- interrupts = <36>;
- interrupt-parent = <&PIC>;
- };
-
-
- e) Marvell Discovery BRG nodes
-
- Represent baud rate generator hardware associated with the MPSC
- (multiprotocol serial controllers).
-
- Required properties:
- - compatible : "marvell,mv64360-brg"
- - reg : Offset and length of the register set for this device
- - clock-src : A value from 0 to 15 which selects the clock
- source for the baud rate generator. This value corresponds
- to the CLKS value in the BRGx configuration register. See
- the mv64x60 User's Manual.
- - clock-frequence : The frequency (in Hz) of the baud rate
- generator's input clock.
- - current-speed : The current speed setting (presumably by
- firmware) of the baud rate generator.
-
- Example Discovery BRG node:
- brg@b200 {
- compatible = "marvell,mv64360-brg";
- reg = <0xb200 0x8>;
- clock-src = <8>;
- clock-frequency = <133333333>;
- current-speed = <9600>;
- };
-
-
- f) Marvell Discovery CUNIT nodes
-
- Represent the Serial Communications Unit device hardware.
-
- Required properties:
- - reg : Offset and length of the register set for this device
-
- Example Discovery CUNIT node:
- cunit@f200 {
- reg = <0xf200 0x200>;
- };
-
-
- g) Marvell Discovery MPSCROUTING nodes
-
- Represent the Discovery's MPSC routing hardware
-
- Required properties:
- - reg : Offset and length of the register set for this device
-
- Example Discovery CUNIT node:
- mpscrouting@b500 {
- reg = <0xb400 0xc>;
- };
-
-
- h) Marvell Discovery MPSCINTR nodes
-
- Represent the Discovery's MPSC DMA interrupt hardware registers
- (SDMA cause and mask registers).
-
- Required properties:
- - reg : Offset and length of the register set for this device
-
- Example Discovery MPSCINTR node:
- mpsintr@b800 {
- reg = <0xb800 0x100>;
- };
-
-
- i) Marvell Discovery MPSC nodes
-
- Represent the Discovery's MPSC (Multiprotocol Serial Controller)
- serial port.
-
- Required properties:
- - device_type : "serial"
- - compatible : "marvell,mv64360-mpsc"
- - reg : Offset and length of the register set for this device
- - sdma : the phandle for the SDMA node used by this port
- - brg : the phandle for the BRG node used by this port
- - cunit : the phandle for the CUNIT node used by this port
- - mpscrouting : the phandle for the MPSCROUTING node used by this port
- - mpscintr : the phandle for the MPSCINTR node used by this port
- - cell-index : the hardware index of this cell in the MPSC core
- - max_idle : value needed for MPSC CHR3 (Maximum Frame Length)
- register
- - interrupts : <a> where a is the interrupt number for the MPSC.
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
-
- Example Discovery MPSCINTR node:
- mpsc@8000 {
- device_type = "serial";
- compatible = "marvell,mv64360-mpsc";
- reg = <0x8000 0x38>;
- virtual-reg = <0xf1008000>;
- sdma = <&SDMA0>;
- brg = <&BRG0>;
- cunit = <&CUNIT>;
- mpscrouting = <&MPSCROUTING>;
- mpscintr = <&MPSCINTR>;
- cell-index = <0>;
- max_idle = <40>;
- interrupts = <40>;
- interrupt-parent = <&PIC>;
- };
-
-
- j) Marvell Discovery Watch Dog Timer nodes
-
- Represent the Discovery's watchdog timer hardware
-
- Required properties:
- - compatible : "marvell,mv64360-wdt"
- - reg : Offset and length of the register set for this device
-
- Example Discovery Watch Dog Timer node:
- wdt@b410 {
- compatible = "marvell,mv64360-wdt";
- reg = <0xb410 0x8>;
- };
-
-
- k) Marvell Discovery I2C nodes
-
- Represent the Discovery's I2C hardware
-
- Required properties:
- - device_type : "i2c"
- - compatible : "marvell,mv64360-i2c"
- - reg : Offset and length of the register set for this device
- - interrupts : <a> where a is the interrupt number for the I2C.
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
-
- Example Discovery I2C node:
- compatible = "marvell,mv64360-i2c";
- reg = <0xc000 0x20>;
- virtual-reg = <0xf100c000>;
- interrupts = <37>;
- interrupt-parent = <&PIC>;
- };
-
-
- l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes
-
- Represent the Discovery's PIC hardware
-
- Required properties:
- - #interrupt-cells : <1>
- - #address-cells : <0>
- - compatible : "marvell,mv64360-pic"
- - reg : Offset and length of the register set for this device
- - interrupt-controller
-
- Example Discovery PIC node:
- pic {
- #interrupt-cells = <1>;
- #address-cells = <0>;
- compatible = "marvell,mv64360-pic";
- reg = <0x0 0x88>;
- interrupt-controller;
- };
-
-
- m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes
-
- Represent the Discovery's MPP hardware
-
- Required properties:
- - compatible : "marvell,mv64360-mpp"
- - reg : Offset and length of the register set for this device
-
- Example Discovery MPP node:
- mpp@f000 {
- compatible = "marvell,mv64360-mpp";
- reg = <0xf000 0x10>;
- };
-
-
- n) Marvell Discovery GPP (General Purpose Pins) nodes
-
- Represent the Discovery's GPP hardware
-
- Required properties:
- - compatible : "marvell,mv64360-gpp"
- - reg : Offset and length of the register set for this device
-
- Example Discovery GPP node:
- gpp@f000 {
- compatible = "marvell,mv64360-gpp";
- reg = <0xf100 0x20>;
- };
-
-
- o) Marvell Discovery PCI host bridge node
-
- Represents the Discovery's PCI host bridge device. The properties
- for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE
- 1275-1994. A typical value for the compatible property is
- "marvell,mv64360-pci".
-
- Example Discovery PCI host bridge node
- pci@80000000 {
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- device_type = "pci";
- compatible = "marvell,mv64360-pci";
- reg = <0xcf8 0x8>;
- ranges = <0x01000000 0x0 0x0
- 0x88000000 0x0 0x01000000
- 0x02000000 0x0 0x80000000
- 0x80000000 0x0 0x08000000>;
- bus-range = <0 255>;
- clock-frequency = <66000000>;
- interrupt-parent = <&PIC>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <
- /* IDSEL 0x0a */
- 0x5000 0 0 1 &PIC 80
- 0x5000 0 0 2 &PIC 81
- 0x5000 0 0 3 &PIC 91
- 0x5000 0 0 4 &PIC 93
-
- /* IDSEL 0x0b */
- 0x5800 0 0 1 &PIC 91
- 0x5800 0 0 2 &PIC 93
- 0x5800 0 0 3 &PIC 80
- 0x5800 0 0 4 &PIC 81
-
- /* IDSEL 0x0c */
- 0x6000 0 0 1 &PIC 91
- 0x6000 0 0 2 &PIC 93
- 0x6000 0 0 3 &PIC 80
- 0x6000 0 0 4 &PIC 81
-
- /* IDSEL 0x0d */
- 0x6800 0 0 1 &PIC 93
- 0x6800 0 0 2 &PIC 80
- 0x6800 0 0 3 &PIC 81
- 0x6800 0 0 4 &PIC 91
- >;
- };
-
-
- p) Marvell Discovery CPU Error nodes
-
- Represent the Discovery's CPU error handler device.
-
- Required properties:
- - compatible : "marvell,mv64360-cpu-error"
- - reg : Offset and length of the register set for this device
- - interrupts : the interrupt number for this device
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
-
- Example Discovery CPU Error node:
- cpu-error@0070 {
- compatible = "marvell,mv64360-cpu-error";
- reg = <0x70 0x10 0x128 0x28>;
- interrupts = <3>;
- interrupt-parent = <&PIC>;
- };
-
-
- q) Marvell Discovery SRAM Controller nodes
-
- Represent the Discovery's SRAM controller device.
-
- Required properties:
- - compatible : "marvell,mv64360-sram-ctrl"
- - reg : Offset and length of the register set for this device
- - interrupts : the interrupt number for this device
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
-
- Example Discovery SRAM Controller node:
- sram-ctrl@0380 {
- compatible = "marvell,mv64360-sram-ctrl";
- reg = <0x380 0x80>;
- interrupts = <13>;
- interrupt-parent = <&PIC>;
- };
-
-
- r) Marvell Discovery PCI Error Handler nodes
-
- Represent the Discovery's PCI error handler device.
-
- Required properties:
- - compatible : "marvell,mv64360-pci-error"
- - reg : Offset and length of the register set for this device
- - interrupts : the interrupt number for this device
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
-
- Example Discovery PCI Error Handler node:
- pci-error@1d40 {
- compatible = "marvell,mv64360-pci-error";
- reg = <0x1d40 0x40 0xc28 0x4>;
- interrupts = <12>;
- interrupt-parent = <&PIC>;
- };
-
-
- s) Marvell Discovery Memory Controller nodes
-
- Represent the Discovery's memory controller device.
-
- Required properties:
- - compatible : "marvell,mv64360-mem-ctrl"
- - reg : Offset and length of the register set for this device
- - interrupts : the interrupt number for this device
- - interrupt-parent : the phandle for the interrupt controller
- that services interrupts for this device.
-
- Example Discovery Memory Controller node:
- mem-ctrl@1400 {
- compatible = "marvell,mv64360-mem-ctrl";
- reg = <0x1400 0x60>;
- interrupts = <17>;
- interrupt-parent = <&PIC>;
- };
-
-
-VIII - Specifying interrupt information for devices
+VII - Specifying interrupt information for devices
===================================================
The device tree represents the busses and devices of a hardware
2 = high to low edge sensitive type enabled
3 = low to high edge sensitive type enabled
-IX - Specifying GPIO information for devices
-============================================
-
-1) gpios property
------------------
-
-Nodes that makes use of GPIOs should define them using `gpios' property,
-format of which is: <&gpio-controller1-phandle gpio1-specifier
- &gpio-controller2-phandle gpio2-specifier
- 0 /* holes are permitted, means no GPIO 3 */
- &gpio-controller4-phandle gpio4-specifier
- ...>;
-
-Note that gpio-specifier length is controller dependent.
-
-gpio-specifier may encode: bank, pin position inside the bank,
-whether pin is open-drain and whether pin is logically inverted.
-
-Example of the node using GPIOs:
-
- node {
- gpios = <&qe_pio_e 18 0>;
- };
-
-In this example gpio-specifier is "18 0" and encodes GPIO pin number,
-and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller.
-
-2) gpio-controller nodes
-------------------------
-
-Every GPIO controller node must have #gpio-cells property defined,
-this information will be used to translate gpio-specifiers.
-
-Example of two SOC GPIO banks defined as gpio-controller nodes:
-
- qe_pio_a: gpio-controller@1400 {
- #gpio-cells = <2>;
- compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank";
- reg = <0x1400 0x18>;
- gpio-controller;
- };
-
- qe_pio_e: gpio-controller@1460 {
- #gpio-cells = <2>;
- compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
- reg = <0x1460 0x18>;
- gpio-controller;
- };
-
-X - Specifying Device Power Management Information (sleep property)
+VIII - Specifying Device Power Management Information (sleep property)
===================================================================
Devices on SOCs often have mechanisms for placing devices into low-power
--- /dev/null
+ 4xx/Axon EMAC ethernet nodes
+
+ The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
+ the Axon bridge. To operate this needs to interact with a ths
+ special McMAL DMA controller, and sometimes an RGMII or ZMII
+ interface. In addition to the nodes and properties described
+ below, the node for the OPB bus on which the EMAC sits must have a
+ correct clock-frequency property.
+
+ i) The EMAC node itself
+
+ Required properties:
+ - device_type : "network"
+
+ - compatible : compatible list, contains 2 entries, first is
+ "ibm,emac-CHIP" where CHIP is the host ASIC (440gx,
+ 405gp, Axon) and second is either "ibm,emac" or
+ "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon",
+ "ibm,emac4"
+ - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ>
+ - interrupt-parent : optional, if needed for interrupt mapping
+ - reg : <registers mapping>
+ - local-mac-address : 6 bytes, MAC address
+ - mal-device : phandle of the associated McMAL node
+ - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated
+ with this EMAC
+ - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated
+ with this EMAC
+ - cell-index : 1 cell, hardware index of the EMAC cell on a given
+ ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on
+ each Axon chip)
+ - max-frame-size : 1 cell, maximum frame size supported in bytes
+ - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec
+ operations.
+ For Axon, 2048
+ - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec
+ operations.
+ For Axon, 2048.
+ - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate
+ thresholds).
+ For Axon, 0x00000010
+ - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds)
+ in bytes.
+ For Axon, 0x00000100 (I think ...)
+ - phy-mode : string, mode of operations of the PHY interface.
+ Supported values are: "mii", "rmii", "smii", "rgmii",
+ "tbi", "gmii", rtbi", "sgmii".
+ For Axon on CAB, it is "rgmii"
+ - mdio-device : 1 cell, required iff using shared MDIO registers
+ (440EP). phandle of the EMAC to use to drive the
+ MDIO lines for the PHY used by this EMAC.
+ - zmii-device : 1 cell, required iff connected to a ZMII. phandle of
+ the ZMII device node
+ - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII
+ channel or 0xffffffff if ZMII is only used for MDIO.
+ - rgmii-device : 1 cell, required iff connected to an RGMII. phandle
+ of the RGMII device node.
+ For Axon: phandle of plb5/plb4/opb/rgmii
+ - rgmii-channel : 1 cell, required iff connected to an RGMII. Which
+ RGMII channel is used by this EMAC.
+ Fox Axon: present, whatever value is appropriate for each
+ EMAC, that is the content of the current (bogus) "phy-port"
+ property.
+
+ Optional properties:
+ - phy-address : 1 cell, optional, MDIO address of the PHY. If absent,
+ a search is performed.
+ - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY
+ for, used if phy-address is absent. bit 0x00000001 is
+ MDIO address 0.
+ For Axon it can be absent, though my current driver
+ doesn't handle phy-address yet so for now, keep
+ 0x00ffffff in it.
+ - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
+ operations (if absent the value is the same as
+ rx-fifo-size). For Axon, either absent or 2048.
+ - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec
+ operations (if absent the value is the same as
+ tx-fifo-size). For Axon, either absent or 2048.
+ - tah-device : 1 cell, optional. If connected to a TAH engine for
+ offload, phandle of the TAH device node.
+ - tah-channel : 1 cell, optional. If appropriate, channel used on the
+ TAH engine.
+
+ Example:
+
+ EMAC0: ethernet@40000800 {
+ device_type = "network";
+ compatible = "ibm,emac-440gp", "ibm,emac";
+ interrupt-parent = <&UIC1>;
+ interrupts = <1c 4 1d 4>;
+ reg = <40000800 70>;
+ local-mac-address = [00 04 AC E3 1B 1E];
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0 1>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <5dc>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rmii";
+ phy-map = <00000001>;
+ zmii-device = <&ZMII0>;
+ zmii-channel = <0>;
+ };
+
+ ii) McMAL node
+
+ Required properties:
+ - device_type : "dma-controller"
+ - compatible : compatible list, containing 2 entries, first is
+ "ibm,mcmal-CHIP" where CHIP is the host ASIC (like
+ emac) and the second is either "ibm,mcmal" or
+ "ibm,mcmal2".
+ For Axon, "ibm,mcmal-axon","ibm,mcmal2"
+ - interrupts : <interrupt mapping for the MAL interrupts sources:
+ 5 sources: tx_eob, rx_eob, serr, txde, rxde>.
+ For Axon: This is _different_ from the current
+ firmware. We use the "delayed" interrupts for txeob
+ and rxeob. Thus we end up with mapping those 5 MPIC
+ interrupts, all level positive sensitive: 10, 11, 32,
+ 33, 34 (in decimal)
+ - dcr-reg : < DCR registers range >
+ - dcr-parent : if needed for dcr-reg
+ - num-tx-chans : 1 cell, number of Tx channels
+ - num-rx-chans : 1 cell, number of Rx channels
+
+ iii) ZMII node
+
+ Required properties:
+ - compatible : compatible list, containing 2 entries, first is
+ "ibm,zmii-CHIP" where CHIP is the host ASIC (like
+ EMAC) and the second is "ibm,zmii".
+ For Axon, there is no ZMII node.
+ - reg : <registers mapping>
+
+ iv) RGMII node
+
+ Required properties:
+ - compatible : compatible list, containing 2 entries, first is
+ "ibm,rgmii-CHIP" where CHIP is the host ASIC (like
+ EMAC) and the second is "ibm,rgmii".
+ For Axon, "ibm,rgmii-axon","ibm,rgmii"
+ - reg : <registers mapping>
+ - revision : as provided by the RGMII new version register if
+ available.
+ For Axon: 0x0000012a
+
--- /dev/null
+Specifying GPIO information for devices
+============================================
+
+1) gpios property
+-----------------
+
+Nodes that makes use of GPIOs should define them using `gpios' property,
+format of which is: <&gpio-controller1-phandle gpio1-specifier
+ &gpio-controller2-phandle gpio2-specifier
+ 0 /* holes are permitted, means no GPIO 3 */
+ &gpio-controller4-phandle gpio4-specifier
+ ...>;
+
+Note that gpio-specifier length is controller dependent.
+
+gpio-specifier may encode: bank, pin position inside the bank,
+whether pin is open-drain and whether pin is logically inverted.
+
+Example of the node using GPIOs:
+
+ node {
+ gpios = <&qe_pio_e 18 0>;
+ };
+
+In this example gpio-specifier is "18 0" and encodes GPIO pin number,
+and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller.
+
+2) gpio-controller nodes
+------------------------
+
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+
+Example of two SOC GPIO banks defined as gpio-controller nodes:
+
+ qe_pio_a: gpio-controller@1400 {
+ #gpio-cells = <2>;
+ compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank";
+ reg = <0x1400 0x18>;
+ gpio-controller;
+ };
+
+ qe_pio_e: gpio-controller@1460 {
+ #gpio-cells = <2>;
+ compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
+ reg = <0x1460 0x18>;
+ gpio-controller;
+ };
+
+
string defining the trigger assigned to the LED. Current triggers are:
"backlight" - LED will act as a back-light, controlled by the framebuffer
system
- "default-on" - LED will turn on
+ "default-on" - LED will turn on, but see "default-state" below
"heartbeat" - LED "double" flashes at a load average based rate
"ide-disk" - LED indicates disk activity
"timer" - LED flashes at a fixed, configurable rate
+- default-state: (optional) The initial state of the LED. Valid
+ values are "on", "off", and "keep". If the LED is already on or off
+ and the default-state property is set the to same value, then no
+ glitch should be produced where the LED momentarily turns off (or
+ on). The "keep" setting will keep the LED at whatever its current
+ state is, without producing a glitch. The default is off if this
+ property is not present.
Examples:
gpios = <&mcu_pio 0 1>; /* Active low */
linux,default-trigger = "ide-disk";
};
+
+ fault {
+ gpios = <&mcu_pio 1 0>;
+ /* Keep LED on if BIOS detected hardware fault */
+ default-state = "keep";
+ };
};
run-control {
compatible = "gpio-leds";
red {
gpios = <&mpc8572 6 0>;
+ default-state = "off";
};
green {
gpios = <&mpc8572 7 0>;
+ default-state = "on";
};
}
--- /dev/null
+MDIO on GPIOs
+
+Currently defined compatibles:
+- virtual,gpio-mdio
+
+MDC and MDIO lines connected to GPIO controllers are listed in the
+gpios property as described in section VIII.1 in the following order:
+
+MDC, MDIO.
+
+Example:
+
+mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qe_pio_a 11
+ &qe_pio_c 6>;
+};
--- /dev/null
+Marvell Discovery mv64[345]6x System Controller chips
+===========================================================
+
+The Marvell mv64[345]60 series of system controller chips contain
+many of the peripherals needed to implement a complete computer
+system. In this section, we define device tree nodes to describe
+the system controller chip itself and each of the peripherals
+which it contains. Compatible string values for each node are
+prefixed with the string "marvell,", for Marvell Technology Group Ltd.
+
+1) The /system-controller node
+
+ This node is used to represent the system-controller and must be
+ present when the system uses a system controller chip. The top-level
+ system-controller node contains information that is global to all
+ devices within the system controller chip. The node name begins
+ with "system-controller" followed by the unit address, which is
+ the base address of the memory-mapped register set for the system
+ controller chip.
+
+ Required properties:
+
+ - ranges : Describes the translation of system controller addresses
+ for memory mapped registers.
+ - clock-frequency: Contains the main clock frequency for the system
+ controller chip.
+ - reg : This property defines the address and size of the
+ memory-mapped registers contained within the system controller
+ chip. The address specified in the "reg" property should match
+ the unit address of the system-controller node.
+ - #address-cells : Address representation for system controller
+ devices. This field represents the number of cells needed to
+ represent the address of the memory-mapped registers of devices
+ within the system controller chip.
+ - #size-cells : Size representation for for the memory-mapped
+ registers within the system controller chip.
+ - #interrupt-cells : Defines the width of cells used to represent
+ interrupts.
+
+ Optional properties:
+
+ - model : The specific model of the system controller chip. Such
+ as, "mv64360", "mv64460", or "mv64560".
+ - compatible : A string identifying the compatibility identifiers
+ of the system controller chip.
+
+ The system-controller node contains child nodes for each system
+ controller device that the platform uses. Nodes should not be created
+ for devices which exist on the system controller chip but are not used
+
+ Example Marvell Discovery mv64360 system-controller node:
+
+ system-controller@f1000000 { /* Marvell Discovery mv64360 */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "mv64360"; /* Default */
+ compatible = "marvell,mv64360";
+ clock-frequency = <133333333>;
+ reg = <0xf1000000 0x10000>;
+ virtual-reg = <0xf1000000>;
+ ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */
+ 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */
+ 0xa0000000 0xa0000000 0x4000000 /* User FLASH */
+ 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */
+ 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */
+
+ [ child node definitions... ]
+ }
+
+2) Child nodes of /system-controller
+
+ a) Marvell Discovery MDIO bus
+
+ The MDIO is a bus to which the PHY devices are connected. For each
+ device that exists on this bus, a child node should be created. See
+ the definition of the PHY node below for an example of how to define
+ a PHY.
+
+ Required properties:
+ - #address-cells : Should be <1>
+ - #size-cells : Should be <0>
+ - device_type : Should be "mdio"
+ - compatible : Should be "marvell,mv64360-mdio"
+
+ Example:
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ device_type = "mdio";
+ compatible = "marvell,mv64360-mdio";
+
+ ethernet-phy@0 {
+ ......
+ };
+ };
+
+
+ b) Marvell Discovery ethernet controller
+
+ The Discover ethernet controller is described with two levels
+ of nodes. The first level describes an ethernet silicon block
+ and the second level describes up to 3 ethernet nodes within
+ that block. The reason for the multiple levels is that the
+ registers for the node are interleaved within a single set
+ of registers. The "ethernet-block" level describes the
+ shared register set, and the "ethernet" nodes describe ethernet
+ port-specific properties.
+
+ Ethernet block node
+
+ Required properties:
+ - #address-cells : <1>
+ - #size-cells : <0>
+ - compatible : "marvell,mv64360-eth-block"
+ - reg : Offset and length of the register set for this block
+
+ Example Discovery Ethernet block node:
+ ethernet-block@2000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,mv64360-eth-block";
+ reg = <0x2000 0x2000>;
+ ethernet@0 {
+ .......
+ };
+ };
+
+ Ethernet port node
+
+ Required properties:
+ - device_type : Should be "network".
+ - compatible : Should be "marvell,mv64360-eth".
+ - reg : Should be <0>, <1>, or <2>, according to which registers
+ within the silicon block the device uses.
+ - interrupts : <a> where a is the interrupt number for the port.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+ - phy : the phandle for the PHY connected to this ethernet
+ controller.
+ - local-mac-address : 6 bytes, MAC address
+
+ Example Discovery Ethernet port node:
+ ethernet@0 {
+ device_type = "network";
+ compatible = "marvell,mv64360-eth";
+ reg = <0>;
+ interrupts = <32>;
+ interrupt-parent = <&PIC>;
+ phy = <&PHY0>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+
+
+ c) Marvell Discovery PHY nodes
+
+ Required properties:
+ - device_type : Should be "ethernet-phy"
+ - interrupts : <a> where a is the interrupt number for this phy.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - reg : The ID number for the phy, usually a small integer
+
+ Example Discovery PHY node:
+ ethernet-phy@1 {
+ device_type = "ethernet-phy";
+ compatible = "broadcom,bcm5421";
+ interrupts = <76>; /* GPP 12 */
+ interrupt-parent = <&PIC>;
+ reg = <1>;
+ };
+
+
+ d) Marvell Discovery SDMA nodes
+
+ Represent DMA hardware associated with the MPSC (multiprotocol
+ serial controllers).
+
+ Required properties:
+ - compatible : "marvell,mv64360-sdma"
+ - reg : Offset and length of the register set for this device
+ - interrupts : <a> where a is the interrupt number for the DMA
+ device.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery SDMA node:
+ sdma@4000 {
+ compatible = "marvell,mv64360-sdma";
+ reg = <0x4000 0xc18>;
+ virtual-reg = <0xf1004000>;
+ interrupts = <36>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ e) Marvell Discovery BRG nodes
+
+ Represent baud rate generator hardware associated with the MPSC
+ (multiprotocol serial controllers).
+
+ Required properties:
+ - compatible : "marvell,mv64360-brg"
+ - reg : Offset and length of the register set for this device
+ - clock-src : A value from 0 to 15 which selects the clock
+ source for the baud rate generator. This value corresponds
+ to the CLKS value in the BRGx configuration register. See
+ the mv64x60 User's Manual.
+ - clock-frequence : The frequency (in Hz) of the baud rate
+ generator's input clock.
+ - current-speed : The current speed setting (presumably by
+ firmware) of the baud rate generator.
+
+ Example Discovery BRG node:
+ brg@b200 {
+ compatible = "marvell,mv64360-brg";
+ reg = <0xb200 0x8>;
+ clock-src = <8>;
+ clock-frequency = <133333333>;
+ current-speed = <9600>;
+ };
+
+
+ f) Marvell Discovery CUNIT nodes
+
+ Represent the Serial Communications Unit device hardware.
+
+ Required properties:
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery CUNIT node:
+ cunit@f200 {
+ reg = <0xf200 0x200>;
+ };
+
+
+ g) Marvell Discovery MPSCROUTING nodes
+
+ Represent the Discovery's MPSC routing hardware
+
+ Required properties:
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery CUNIT node:
+ mpscrouting@b500 {
+ reg = <0xb400 0xc>;
+ };
+
+
+ h) Marvell Discovery MPSCINTR nodes
+
+ Represent the Discovery's MPSC DMA interrupt hardware registers
+ (SDMA cause and mask registers).
+
+ Required properties:
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery MPSCINTR node:
+ mpsintr@b800 {
+ reg = <0xb800 0x100>;
+ };
+
+
+ i) Marvell Discovery MPSC nodes
+
+ Represent the Discovery's MPSC (Multiprotocol Serial Controller)
+ serial port.
+
+ Required properties:
+ - device_type : "serial"
+ - compatible : "marvell,mv64360-mpsc"
+ - reg : Offset and length of the register set for this device
+ - sdma : the phandle for the SDMA node used by this port
+ - brg : the phandle for the BRG node used by this port
+ - cunit : the phandle for the CUNIT node used by this port
+ - mpscrouting : the phandle for the MPSCROUTING node used by this port
+ - mpscintr : the phandle for the MPSCINTR node used by this port
+ - cell-index : the hardware index of this cell in the MPSC core
+ - max_idle : value needed for MPSC CHR3 (Maximum Frame Length)
+ register
+ - interrupts : <a> where a is the interrupt number for the MPSC.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery MPSCINTR node:
+ mpsc@8000 {
+ device_type = "serial";
+ compatible = "marvell,mv64360-mpsc";
+ reg = <0x8000 0x38>;
+ virtual-reg = <0xf1008000>;
+ sdma = <&SDMA0>;
+ brg = <&BRG0>;
+ cunit = <&CUNIT>;
+ mpscrouting = <&MPSCROUTING>;
+ mpscintr = <&MPSCINTR>;
+ cell-index = <0>;
+ max_idle = <40>;
+ interrupts = <40>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ j) Marvell Discovery Watch Dog Timer nodes
+
+ Represent the Discovery's watchdog timer hardware
+
+ Required properties:
+ - compatible : "marvell,mv64360-wdt"
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery Watch Dog Timer node:
+ wdt@b410 {
+ compatible = "marvell,mv64360-wdt";
+ reg = <0xb410 0x8>;
+ };
+
+
+ k) Marvell Discovery I2C nodes
+
+ Represent the Discovery's I2C hardware
+
+ Required properties:
+ - device_type : "i2c"
+ - compatible : "marvell,mv64360-i2c"
+ - reg : Offset and length of the register set for this device
+ - interrupts : <a> where a is the interrupt number for the I2C.
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery I2C node:
+ compatible = "marvell,mv64360-i2c";
+ reg = <0xc000 0x20>;
+ virtual-reg = <0xf100c000>;
+ interrupts = <37>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes
+
+ Represent the Discovery's PIC hardware
+
+ Required properties:
+ - #interrupt-cells : <1>
+ - #address-cells : <0>
+ - compatible : "marvell,mv64360-pic"
+ - reg : Offset and length of the register set for this device
+ - interrupt-controller
+
+ Example Discovery PIC node:
+ pic {
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ compatible = "marvell,mv64360-pic";
+ reg = <0x0 0x88>;
+ interrupt-controller;
+ };
+
+
+ m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes
+
+ Represent the Discovery's MPP hardware
+
+ Required properties:
+ - compatible : "marvell,mv64360-mpp"
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery MPP node:
+ mpp@f000 {
+ compatible = "marvell,mv64360-mpp";
+ reg = <0xf000 0x10>;
+ };
+
+
+ n) Marvell Discovery GPP (General Purpose Pins) nodes
+
+ Represent the Discovery's GPP hardware
+
+ Required properties:
+ - compatible : "marvell,mv64360-gpp"
+ - reg : Offset and length of the register set for this device
+
+ Example Discovery GPP node:
+ gpp@f000 {
+ compatible = "marvell,mv64360-gpp";
+ reg = <0xf100 0x20>;
+ };
+
+
+ o) Marvell Discovery PCI host bridge node
+
+ Represents the Discovery's PCI host bridge device. The properties
+ for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE
+ 1275-1994. A typical value for the compatible property is
+ "marvell,mv64360-pci".
+
+ Example Discovery PCI host bridge node
+ pci@80000000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ compatible = "marvell,mv64360-pci";
+ reg = <0xcf8 0x8>;
+ ranges = <0x01000000 0x0 0x0
+ 0x88000000 0x0 0x01000000
+ 0x02000000 0x0 0x80000000
+ 0x80000000 0x0 0x08000000>;
+ bus-range = <0 255>;
+ clock-frequency = <66000000>;
+ interrupt-parent = <&PIC>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 0x0a */
+ 0x5000 0 0 1 &PIC 80
+ 0x5000 0 0 2 &PIC 81
+ 0x5000 0 0 3 &PIC 91
+ 0x5000 0 0 4 &PIC 93
+
+ /* IDSEL 0x0b */
+ 0x5800 0 0 1 &PIC 91
+ 0x5800 0 0 2 &PIC 93
+ 0x5800 0 0 3 &PIC 80
+ 0x5800 0 0 4 &PIC 81
+
+ /* IDSEL 0x0c */
+ 0x6000 0 0 1 &PIC 91
+ 0x6000 0 0 2 &PIC 93
+ 0x6000 0 0 3 &PIC 80
+ 0x6000 0 0 4 &PIC 81
+
+ /* IDSEL 0x0d */
+ 0x6800 0 0 1 &PIC 93
+ 0x6800 0 0 2 &PIC 80
+ 0x6800 0 0 3 &PIC 81
+ 0x6800 0 0 4 &PIC 91
+ >;
+ };
+
+
+ p) Marvell Discovery CPU Error nodes
+
+ Represent the Discovery's CPU error handler device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-cpu-error"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery CPU Error node:
+ cpu-error@0070 {
+ compatible = "marvell,mv64360-cpu-error";
+ reg = <0x70 0x10 0x128 0x28>;
+ interrupts = <3>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ q) Marvell Discovery SRAM Controller nodes
+
+ Represent the Discovery's SRAM controller device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-sram-ctrl"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery SRAM Controller node:
+ sram-ctrl@0380 {
+ compatible = "marvell,mv64360-sram-ctrl";
+ reg = <0x380 0x80>;
+ interrupts = <13>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ r) Marvell Discovery PCI Error Handler nodes
+
+ Represent the Discovery's PCI error handler device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-pci-error"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery PCI Error Handler node:
+ pci-error@1d40 {
+ compatible = "marvell,mv64360-pci-error";
+ reg = <0x1d40 0x40 0xc28 0x4>;
+ interrupts = <12>;
+ interrupt-parent = <&PIC>;
+ };
+
+
+ s) Marvell Discovery Memory Controller nodes
+
+ Represent the Discovery's memory controller device.
+
+ Required properties:
+ - compatible : "marvell,mv64360-mem-ctrl"
+ - reg : Offset and length of the register set for this device
+ - interrupts : the interrupt number for this device
+ - interrupt-parent : the phandle for the interrupt controller
+ that services interrupts for this device.
+
+ Example Discovery Memory Controller node:
+ mem-ctrl@1400 {
+ compatible = "marvell,mv64360-mem-ctrl";
+ reg = <0x1400 0x60>;
+ interrupts = <17>;
+ interrupt-parent = <&PIC>;
+ };
+
+
--- /dev/null
+PHY nodes
+
+Required properties:
+
+ - device_type : Should be "ethernet-phy"
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - reg : The ID number for the phy, usually a small integer
+ - linux,phandle : phandle for this node; likely referenced by an
+ ethernet controller node.
+
+Example:
+
+ethernet-phy@0 {
+ linux,phandle = <2452000>
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+};
--- /dev/null
+SPI (Serial Peripheral Interface) busses
+
+SPI busses can be described with a node for the SPI master device
+and a set of child nodes for each SPI slave on the bus. For this
+discussion, it is assumed that the system's SPI controller is in
+SPI master mode. This binding does not describe SPI controllers
+in slave mode.
+
+The SPI master node requires the following properties:
+- #address-cells - number of cells required to define a chip select
+ address on the SPI bus.
+- #size-cells - should be zero.
+- compatible - name of SPI bus controller following generic names
+ recommended practice.
+No other properties are required in the SPI bus node. It is assumed
+that a driver for an SPI bus device will understand that it is an SPI bus.
+However, the binding does not attempt to define the specific method for
+assigning chip select numbers. Since SPI chip select configuration is
+flexible and non-standardized, it is left out of this binding with the
+assumption that board specific platform code will be used to manage
+chip selects. Individual drivers can define additional properties to
+support describing the chip select layout.
+
+SPI slave nodes must be children of the SPI master node and can
+contain the following properties.
+- reg - (required) chip select address of device.
+- compatible - (required) name of SPI device following generic names
+ recommended practice
+- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+- spi-cpol - (optional) Empty property indicating device requires
+ inverse clock polarity (CPOL) mode
+- spi-cpha - (optional) Empty property indicating device requires
+ shifted clock phase (CPHA) mode
+- spi-cs-high - (optional) Empty property indicating device requires
+ chip select active high
+
+SPI example for an MPC5200 SPI bus:
+ spi@f00 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+ reg = <0xf00 0x20>;
+ interrupts = <2 13 0 2 14 0>;
+ interrupt-parent = <&mpc5200_pic>;
+
+ ethernet-switch@0 {
+ compatible = "micrel,ks8995m";
+ spi-max-frequency = <1000000>;
+ reg = <0>;
+ };
+
+ codec@1 {
+ compatible = "ti,tlv320aic26";
+ spi-max-frequency = <100000>;
+ reg = <1>;
+ };
+ };
--- /dev/null
+USB EHCI controllers
+
+Required properties:
+ - compatible : should be "usb-ehci".
+ - reg : should contain at least address and length of the standard EHCI
+ register set for the device. Optional platform-dependent registers
+ (debug-port or other) can be also specified here, but only after
+ definition of standard EHCI registers.
+ - interrupts : one EHCI interrupt should be described here.
+If device registers are implemented in big endian mode, the device
+node should have "big-endian-regs" property.
+If controller implementation operates with big endian descriptors,
+"big-endian-desc" property should be specified.
+If both big endian registers and descriptors are used by the controller
+implementation, "big-endian" property can be specified instead of having
+both "big-endian-regs" and "big-endian-desc".
+
+Example (Sequoia 440EPx):
+ ehci@e0000300 {
+ compatible = "ibm,usb-ehci-440epx", "usb-ehci";
+ interrupt-parent = <&UIC0>;
+ interrupts = <1a 4>;
+ reg = <0 e0000300 90 0 e0000390 70>;
+ big-endian;
+ };
--- /dev/null
+ d) Xilinx IP cores
+
+ The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
+ in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
+ of standard device types (network, serial, etc.) and miscellaneous
+ devices (gpio, LCD, spi, etc). Also, since these devices are
+ implemented within the fpga fabric every instance of the device can be
+ synthesised with different options that change the behaviour.
+
+ Each IP-core has a set of parameters which the FPGA designer can use to
+ control how the core is synthesized. Historically, the EDK tool would
+ extract the device parameters relevant to device drivers and copy them
+ into an 'xparameters.h' in the form of #define symbols. This tells the
+ device drivers how the IP cores are configured, but it requres the kernel
+ to be recompiled every time the FPGA bitstream is resynthesized.
+
+ The new approach is to export the parameters into the device tree and
+ generate a new device tree each time the FPGA bitstream changes. The
+ parameters which used to be exported as #defines will now become
+ properties of the device node. In general, device nodes for IP-cores
+ will take the following form:
+
+ (name): (generic-name)@(base-address) {
+ compatible = "xlnx,(ip-core-name)-(HW_VER)"
+ [, (list of compatible devices), ...];
+ reg = <(baseaddr) (size)>;
+ interrupt-parent = <&interrupt-controller-phandle>;
+ interrupts = < ... >;
+ xlnx,(parameter1) = "(string-value)";
+ xlnx,(parameter2) = <(int-value)>;
+ };
+
+ (generic-name): an open firmware-style name that describes the
+ generic class of device. Preferably, this is one word, such
+ as 'serial' or 'ethernet'.
+ (ip-core-name): the name of the ip block (given after the BEGIN
+ directive in system.mhs). Should be in lowercase
+ and all underscores '_' converted to dashes '-'.
+ (name): is derived from the "PARAMETER INSTANCE" value.
+ (parameter#): C_* parameters from system.mhs. The C_ prefix is
+ dropped from the parameter name, the name is converted
+ to lowercase and all underscore '_' characters are
+ converted to dashes '-'.
+ (baseaddr): the baseaddr parameter value (often named C_BASEADDR).
+ (HW_VER): from the HW_VER parameter.
+ (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1).
+
+ Typically, the compatible list will include the exact IP core version
+ followed by an older IP core version which implements the same
+ interface or any other device with the same interface.
+
+ 'reg', 'interrupt-parent' and 'interrupts' are all optional properties.
+
+ For example, the following block from system.mhs:
+
+ BEGIN opb_uartlite
+ PARAMETER INSTANCE = opb_uartlite_0
+ PARAMETER HW_VER = 1.00.b
+ PARAMETER C_BAUDRATE = 115200
+ PARAMETER C_DATA_BITS = 8
+ PARAMETER C_ODD_PARITY = 0
+ PARAMETER C_USE_PARITY = 0
+ PARAMETER C_CLK_FREQ = 50000000
+ PARAMETER C_BASEADDR = 0xEC100000
+ PARAMETER C_HIGHADDR = 0xEC10FFFF
+ BUS_INTERFACE SOPB = opb_7
+ PORT OPB_Clk = CLK_50MHz
+ PORT Interrupt = opb_uartlite_0_Interrupt
+ PORT RX = opb_uartlite_0_RX
+ PORT TX = opb_uartlite_0_TX
+ PORT OPB_Rst = sys_bus_reset_0
+ END
+
+ becomes the following device tree node:
+
+ opb_uartlite_0: serial@ec100000 {
+ device_type = "serial";
+ compatible = "xlnx,opb-uartlite-1.00.b";
+ reg = <ec100000 10000>;
+ interrupt-parent = <&opb_intc_0>;
+ interrupts = <1 0>; // got this from the opb_intc parameters
+ current-speed = <d#115200>; // standard serial device prop
+ clock-frequency = <d#50000000>; // standard serial device prop
+ xlnx,data-bits = <8>;
+ xlnx,odd-parity = <0>;
+ xlnx,use-parity = <0>;
+ };
+
+ Some IP cores actually implement 2 or more logical devices. In
+ this case, the device should still describe the whole IP core with
+ a single node and add a child node for each logical device. The
+ ranges property can be used to translate from parent IP-core to the
+ registers of each device. In addition, the parent node should be
+ compatible with the bus type 'xlnx,compound', and should contain
+ #address-cells and #size-cells, as with any other bus. (Note: this
+ makes the assumption that both logical devices have the same bus
+ binding. If this is not true, then separate nodes should be used
+ for each logical device). The 'cell-index' property can be used to
+ enumerate logical devices within an IP core. For example, the
+ following is the system.mhs entry for the dual ps2 controller found
+ on the ml403 reference design.
+
+ BEGIN opb_ps2_dual_ref
+ PARAMETER INSTANCE = opb_ps2_dual_ref_0
+ PARAMETER HW_VER = 1.00.a
+ PARAMETER C_BASEADDR = 0xA9000000
+ PARAMETER C_HIGHADDR = 0xA9001FFF
+ BUS_INTERFACE SOPB = opb_v20_0
+ PORT Sys_Intr1 = ps2_1_intr
+ PORT Sys_Intr2 = ps2_2_intr
+ PORT Clkin1 = ps2_clk_rx_1
+ PORT Clkin2 = ps2_clk_rx_2
+ PORT Clkpd1 = ps2_clk_tx_1
+ PORT Clkpd2 = ps2_clk_tx_2
+ PORT Rx1 = ps2_d_rx_1
+ PORT Rx2 = ps2_d_rx_2
+ PORT Txpd1 = ps2_d_tx_1
+ PORT Txpd2 = ps2_d_tx_2
+ END
+
+ It would result in the following device tree nodes:
+
+ opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "xlnx,compound";
+ ranges = <0 a9000000 2000>;
+ // If this device had extra parameters, then they would
+ // go here.
+ ps2@0 {
+ compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
+ reg = <0 40>;
+ interrupt-parent = <&opb_intc_0>;
+ interrupts = <3 0>;
+ cell-index = <0>;
+ };
+ ps2@1000 {
+ compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
+ reg = <1000 40>;
+ interrupt-parent = <&opb_intc_0>;
+ interrupts = <3 0>;
+ cell-index = <0>;
+ };
+ };
+
+ Also, the system.mhs file defines bus attachments from the processor
+ to the devices. The device tree structure should reflect the bus
+ attachments. Again an example; this system.mhs fragment:
+
+ BEGIN ppc405_virtex4
+ PARAMETER INSTANCE = ppc405_0
+ PARAMETER HW_VER = 1.01.a
+ BUS_INTERFACE DPLB = plb_v34_0
+ BUS_INTERFACE IPLB = plb_v34_0
+ END
+
+ BEGIN opb_intc
+ PARAMETER INSTANCE = opb_intc_0
+ PARAMETER HW_VER = 1.00.c
+ PARAMETER C_BASEADDR = 0xD1000FC0
+ PARAMETER C_HIGHADDR = 0xD1000FDF
+ BUS_INTERFACE SOPB = opb_v20_0
+ END
+
+ BEGIN opb_uart16550
+ PARAMETER INSTANCE = opb_uart16550_0
+ PARAMETER HW_VER = 1.00.d
+ PARAMETER C_BASEADDR = 0xa0000000
+ PARAMETER C_HIGHADDR = 0xa0001FFF
+ BUS_INTERFACE SOPB = opb_v20_0
+ END
+
+ BEGIN plb_v34
+ PARAMETER INSTANCE = plb_v34_0
+ PARAMETER HW_VER = 1.02.a
+ END
+
+ BEGIN plb_bram_if_cntlr
+ PARAMETER INSTANCE = plb_bram_if_cntlr_0
+ PARAMETER HW_VER = 1.00.b
+ PARAMETER C_BASEADDR = 0xFFFF0000
+ PARAMETER C_HIGHADDR = 0xFFFFFFFF
+ BUS_INTERFACE SPLB = plb_v34_0
+ END
+
+ BEGIN plb2opb_bridge
+ PARAMETER INSTANCE = plb2opb_bridge_0
+ PARAMETER HW_VER = 1.01.a
+ PARAMETER C_RNG0_BASEADDR = 0x20000000
+ PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF
+ PARAMETER C_RNG1_BASEADDR = 0x60000000
+ PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF
+ PARAMETER C_RNG2_BASEADDR = 0x80000000
+ PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF
+ PARAMETER C_RNG3_BASEADDR = 0xC0000000
+ PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF
+ BUS_INTERFACE SPLB = plb_v34_0
+ BUS_INTERFACE MOPB = opb_v20_0
+ END
+
+ Gives this device tree (some properties removed for clarity):
+
+ plb@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "xlnx,plb-v34-1.02.a";
+ device_type = "ibm,plb";
+ ranges; // 1:1 translation
+
+ plb_bram_if_cntrl_0: bram@ffff0000 {
+ reg = <ffff0000 10000>;
+ }
+
+ opb@20000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <20000000 20000000 20000000
+ 60000000 60000000 20000000
+ 80000000 80000000 40000000
+ c0000000 c0000000 20000000>;
+
+ opb_uart16550_0: serial@a0000000 {
+ reg = <a00000000 2000>;
+ };
+
+ opb_intc_0: interrupt-controller@d1000fc0 {
+ reg = <d1000fc0 20>;
+ };
+ };
+ };
+
+ That covers the general approach to binding xilinx IP cores into the
+ device tree. The following are bindings for specific devices:
+
+ i) Xilinx ML300 Framebuffer
+
+ Simple framebuffer device from the ML300 reference design (also on the
+ ML403 reference design as well as others).
+
+ Optional properties:
+ - resolution = <xres yres> : pixel resolution of framebuffer. Some
+ implementations use a different resolution.
+ Default is <d#640 d#480>
+ - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory.
+ Default is <d#1024 d#480>.
+ - rotate-display (empty) : rotate display 180 degrees.
+
+ ii) Xilinx SystemACE
+
+ The Xilinx SystemACE device is used to program FPGAs from an FPGA
+ bitstream stored on a CF card. It can also be used as a generic CF
+ interface device.
+
+ Optional properties:
+ - 8-bit (empty) : Set this property for SystemACE in 8 bit mode
+
+ iii) Xilinx EMAC and Xilinx TEMAC
+
+ Xilinx Ethernet devices. In addition to general xilinx properties
+ listed above, nodes for these devices should include a phy-handle
+ property, and may include other common network device properties
+ like local-mac-address.
+
+ iv) Xilinx Uartlite
+
+ Xilinx uartlite devices are simple fixed speed serial ports.
+
+ Required properties:
+ - current-speed : Baud rate of uartlite
+
+ v) Xilinx hwicap
+
+ Xilinx hwicap devices provide access to the configuration logic
+ of the FPGA through the Internal Configuration Access Port
+ (ICAP). The ICAP enables partial reconfiguration of the FPGA,
+ readback of the configuration information, and some control over
+ 'warm boots' of the FPGA fabric.
+
+ Required properties:
+ - xlnx,family : The family of the FPGA, necessary since the
+ capabilities of the underlying ICAP hardware
+ differ between different families. May be
+ 'virtex2p', 'virtex4', or 'virtex5'.
+
+ vi) Xilinx Uart 16550
+
+ Xilinx UART 16550 devices are very similar to the NS16550 but with
+ different register spacing and an offset from the base address.
+
+ Required properties:
+ - clock-frequency : Frequency of the clock input
+ - reg-offset : A value of 3 is required
+ - reg-shift : A value of 2 is required
+
+
*
*/
#undef CONFIG_MODULES
+#include <linux/module.h>
+#undef CONFIG_KALLSYMS
+#undef EXPORT_SYMBOL
+#undef EXPORT_SYMBOL_GPL
+#define EXPORT_SYMBOL(sym)
+#define EXPORT_SYMBOL_GPL(sym)
#include "../../../lib/vsprintf.c"
#include "../../../lib/ctype.c"
config TRACE_IRQFLAGS_SUPPORT
bool
- depends on PPC64
default y
config LOCKDEP_SUPPORT
zconf.h
zlib.h
zutil.h
+fdt.c
+fdt.h
+fdt_ro.c
+fdt_rw.c
+fdt_strerror.c
+fdt_sw.c
+fdt_wip.c
+libfdt.h
+libfdt_internal.h
+
devsel-speed = <0x00000001>;
min-grant = <0>;
max-latency = <0>;
- /* First 64k for I/O at 0x0 on PCI mapped to 0x0 on ISA. */
- ranges = <0x00000001 0 0x01000000 0 0x00000000 0x00010000>;
+ /* First 4k for I/O at 0x0 on PCI mapped to 0x0 on ISA. */
+ ranges = <0x00000001 0 0x01000000 0 0x00000000 0x00001000>;
interrupt-parent = <&i8259>;
#interrupt-cells = <2>;
#address-cells = <2>;
/* Filled in by U-Boot */
clock-frequency = <0>;
status = "disabled";
+ sdhci,1-bit-only;
};
crypto@30000 {
#define CICR_IEN ((uint)0x00000080) /* Int. enable */
#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
-#define IMAP_ADDR (get_immrbase())
-
#define CPM_PIN_INPUT 0
#define CPM_PIN_OUTPUT 1
#define CPM_PIN_PRIMARY 0
struct dma_mapping_ops *dma_ops = get_dma_ops(dev);
BUG_ON(!dma_ops);
- dma_ops->sync_single_range_for_cpu(dev, dma_handle, 0,
+
+ if (dma_ops->sync_single_range_for_cpu)
+ dma_ops->sync_single_range_for_cpu(dev, dma_handle, 0,
size, direction);
}
struct dma_mapping_ops *dma_ops = get_dma_ops(dev);
BUG_ON(!dma_ops);
- dma_ops->sync_single_range_for_device(dev, dma_handle,
+
+ if (dma_ops->sync_single_range_for_device)
+ dma_ops->sync_single_range_for_device(dev, dma_handle,
0, size, direction);
}
struct dma_mapping_ops *dma_ops = get_dma_ops(dev);
BUG_ON(!dma_ops);
- dma_ops->sync_sg_for_cpu(dev, sgl, nents, direction);
+
+ if (dma_ops->sync_sg_for_cpu)
+ dma_ops->sync_sg_for_cpu(dev, sgl, nents, direction);
}
static inline void dma_sync_sg_for_device(struct device *dev,
struct dma_mapping_ops *dma_ops = get_dma_ops(dev);
BUG_ON(!dma_ops);
- dma_ops->sync_sg_for_device(dev, sgl, nents, direction);
+
+ if (dma_ops->sync_sg_for_device)
+ dma_ops->sync_sg_for_device(dev, sgl, nents, direction);
}
static inline void dma_sync_single_range_for_cpu(struct device *dev,
struct dma_mapping_ops *dma_ops = get_dma_ops(dev);
BUG_ON(!dma_ops);
- dma_ops->sync_single_range_for_cpu(dev, dma_handle,
+
+ if (dma_ops->sync_single_range_for_cpu)
+ dma_ops->sync_single_range_for_cpu(dev, dma_handle,
offset, size, direction);
}
struct dma_mapping_ops *dma_ops = get_dma_ops(dev);
BUG_ON(!dma_ops);
- dma_ops->sync_single_range_for_device(dev, dma_handle, offset,
+
+ if (dma_ops->sync_single_range_for_device)
+ dma_ops->sync_single_range_for_device(dev, dma_handle, offset,
size, direction);
}
#else /* CONFIG_PPC_NEED_DMA_SYNC_OPS */
#ifdef __KERNEL__
-#include <linux/init.h>
#include <linux/interrupt.h>
-#include <linux/highmem.h>
#include <asm/kmap_types.h>
#include <asm/tlbflush.h>
#include <asm/page.h>
extern void *kmap_high(struct page *page);
extern void kunmap_high(struct page *page);
+extern void *kmap_atomic_prot(struct page *page, enum km_type type,
+ pgprot_t prot);
+extern void kunmap_atomic(void *kvaddr, enum km_type type);
static inline void *kmap(struct page *page)
{
kunmap_high(page);
}
-/*
- * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap
- * gives a more generic (and caching) interface. But kmap_atomic can
- * be used in IRQ contexts, so in some (very limited) cases we need
- * it.
- */
-static inline void *kmap_atomic_prot(struct page *page, enum km_type type, pgprot_t prot)
-{
- unsigned int idx;
- unsigned long vaddr;
-
- /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */
- pagefault_disable();
- if (!PageHighMem(page))
- return page_address(page);
-
- debug_kmap_atomic(type);
- idx = type + KM_TYPE_NR*smp_processor_id();
- vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx);
-#ifdef CONFIG_DEBUG_HIGHMEM
- BUG_ON(!pte_none(*(kmap_pte-idx)));
-#endif
- __set_pte_at(&init_mm, vaddr, kmap_pte-idx, mk_pte(page, prot), 1);
- local_flush_tlb_page(NULL, vaddr);
-
- return (void*) vaddr;
-}
-
static inline void *kmap_atomic(struct page *page, enum km_type type)
{
return kmap_atomic_prot(page, type, kmap_prot);
}
-static inline void kunmap_atomic(void *kvaddr, enum km_type type)
-{
-#ifdef CONFIG_DEBUG_HIGHMEM
- unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK;
- enum fixed_addresses idx = type + KM_TYPE_NR*smp_processor_id();
-
- if (vaddr < __fix_to_virt(FIX_KMAP_END)) {
- pagefault_enable();
- return;
- }
-
- BUG_ON(vaddr != __fix_to_virt(FIX_KMAP_BEGIN + idx));
-
- /*
- * force other mappings to Oops if they'll try to access
- * this pte without first remap it
- */
- pte_clear(&init_mm, vaddr, kmap_pte-idx);
- local_flush_tlb_page(NULL, vaddr);
-#endif
- pagefault_enable();
-}
-
static inline struct page *kmap_atomic_to_page(void *ptr)
{
unsigned long idx, vaddr = (unsigned long) ptr;
return pte_page(*pte);
}
+
#define flush_cache_kmaps() flush_cache_all()
#endif /* __KERNEL__ */
#if defined(CONFIG_BOOKE)
#define SET_MSR_EE(x) mtmsr(x)
-#define local_irq_restore(flags) __asm__ __volatile__("wrtee %0" : : "r" (flags) : "memory")
+#define raw_local_irq_restore(flags) __asm__ __volatile__("wrtee %0" : : "r" (flags) : "memory")
#else
#define SET_MSR_EE(x) mtmsr(x)
-#define local_irq_restore(flags) mtmsr(flags)
+#define raw_local_irq_restore(flags) mtmsr(flags)
#endif
-static inline void local_irq_disable(void)
+static inline void raw_local_irq_disable(void)
{
#ifdef CONFIG_BOOKE
__asm__ __volatile__("wrteei 0": : :"memory");
#endif
}
-static inline void local_irq_enable(void)
+static inline void raw_local_irq_enable(void)
{
#ifdef CONFIG_BOOKE
__asm__ __volatile__("wrteei 1": : :"memory");
#endif
}
-static inline void local_irq_save_ptr(unsigned long *flags)
+static inline void raw_local_irq_save_ptr(unsigned long *flags)
{
unsigned long msr;
msr = mfmsr();
#endif
}
-#define local_save_flags(flags) ((flags) = mfmsr())
-#define local_irq_save(flags) local_irq_save_ptr(&flags)
-#define irqs_disabled() ((mfmsr() & MSR_EE) == 0)
+#define raw_local_save_flags(flags) ((flags) = mfmsr())
+#define raw_local_irq_save(flags) raw_local_irq_save_ptr(&flags)
+#define raw_irqs_disabled() ((mfmsr() & MSR_EE) == 0)
+#define raw_irqs_disabled_flags(flags) (((flags) & MSR_EE) == 0)
-#define hard_irq_enable() local_irq_enable()
-#define hard_irq_disable() local_irq_disable()
+#define hard_irq_disable() raw_local_irq_disable()
static inline int irqs_disabled_flags(unsigned long flags)
{
* generic accessors and iterators here
*/
#define __real_pte(e,p) ((real_pte_t) { \
- (e), pte_val(*((p) + PTRS_PER_PTE)) })
+ (e), ((e) & _PAGE_COMBO) ? \
+ (pte_val(*((p) + PTRS_PER_PTE))) : 0 })
#define __rpte_to_hidx(r,index) ((pte_val((r).pte) & _PAGE_COMBO) ? \
(((r).hidx >> ((index)<<2)) & 0xf) : ((pte_val((r).pte) >> 12) & 0xf))
#define __rpte_to_pte(r) ((r).pte)
unsigned long entry; /* physical address pointer */
unsigned long base; /* physical address pointer */
unsigned long size;
- spinlock_t lock;
+ raw_spinlock_t lock;
struct rtas_args args;
struct device_node *dev; /* virtual address pointer */
};
(devfn << 8) | (reg & 0xff);
}
+extern void __cpuinit rtas_give_timebase(void);
+extern void __cpuinit rtas_take_timebase(void);
+
#endif /* __KERNEL__ */
#endif /* _POWERPC_RTAS_H */
mflr r9
lwz r11,0(r9) /* virtual address of handler */
lwz r9,4(r9) /* where to go when done */
+#ifdef CONFIG_TRACE_IRQFLAGS
+ lis r12,reenable_mmu@h
+ ori r12,r12,reenable_mmu@l
+ mtspr SPRN_SRR0,r12
+ mtspr SPRN_SRR1,r10
+ SYNC
+ RFI
+reenable_mmu: /* re-enable mmu so we can */
+ mfmsr r10
+ lwz r12,_MSR(r1)
+ xor r10,r10,r12
+ andi. r10,r10,MSR_EE /* Did EE change? */
+ beq 1f
+
+ /* Save handler and return address into the 2 unused words
+ * of the STACK_FRAME_OVERHEAD (sneak sneak sneak). Everything
+ * else can be recovered from the pt_regs except r3 which for
+ * normal interrupts has been set to pt_regs and for syscalls
+ * is an argument, so we temporarily use ORIG_GPR3 to save it
+ */
+ stw r9,8(r1)
+ stw r11,12(r1)
+ stw r3,ORIG_GPR3(r1)
+ bl trace_hardirqs_off
+ lwz r0,GPR0(r1)
+ lwz r3,ORIG_GPR3(r1)
+ lwz r4,GPR4(r1)
+ lwz r5,GPR5(r1)
+ lwz r6,GPR6(r1)
+ lwz r7,GPR7(r1)
+ lwz r8,GPR8(r1)
+ lwz r9,8(r1)
+ lwz r11,12(r1)
+1: mtctr r11
+ mtlr r9
+ bctr /* jump to handler */
+#else /* CONFIG_TRACE_IRQFLAGS */
mtspr SPRN_SRR0,r11
mtspr SPRN_SRR1,r10
mtlr r9
SYNC
RFI /* jump to handler, enable MMU */
+#endif /* CONFIG_TRACE_IRQFLAGS */
#if defined (CONFIG_6xx) || defined(CONFIG_E500)
4: rlwinm r12,r12,0,~_TLF_NAPPING
#ifdef SHOW_SYSCALLS
bl do_show_syscall
#endif /* SHOW_SYSCALLS */
+#ifdef CONFIG_TRACE_IRQFLAGS
+ /* Return from syscalls can (and generally will) hard enable
+ * interrupts. You aren't supposed to call a syscall with
+ * interrupts disabled in the first place. However, to ensure
+ * that we get it right vs. lockdep if it happens, we force
+ * that hard enable here with appropriate tracing if we see
+ * that we have been called with interrupts off
+ */
+ mfmsr r11
+ andi. r12,r11,MSR_EE
+ bne+ 1f
+ /* We came in with interrupts disabled, we enable them now */
+ bl trace_hardirqs_on
+ mfmsr r11
+ lwz r0,GPR0(r1)
+ lwz r3,GPR3(r1)
+ lwz r4,GPR4(r1)
+ ori r11,r11,MSR_EE
+ lwz r5,GPR5(r1)
+ lwz r6,GPR6(r1)
+ lwz r7,GPR7(r1)
+ lwz r8,GPR8(r1)
+ mtmsr r11
+1:
+#endif /* CONFIG_TRACE_IRQFLAGS */
rlwinm r10,r1,0,0,(31-THREAD_SHIFT) /* current_thread_info() */
lwz r11,TI_FLAGS(r10)
andi. r11,r11,_TIF_SYSCALL_T_OR_A
rlwinm r12,r1,0,0,(31-THREAD_SHIFT) /* current_thread_info() */
/* disable interrupts so current_thread_info()->flags can't change */
LOAD_MSR_KERNEL(r10,MSR_KERNEL) /* doesn't include MSR_EE */
+ /* Note: We don't bother telling lockdep about it */
SYNC
MTMSRD(r10)
lwz r9,TI_FLAGS(r12)
oris r11,r11,0x1000 /* Set SO bit in CR */
stw r11,_CCR(r1)
syscall_exit_cont:
+ lwz r8,_MSR(r1)
+#ifdef CONFIG_TRACE_IRQFLAGS
+ /* If we are going to return from the syscall with interrupts
+ * off, we trace that here. It shouldn't happen though but we
+ * want to catch the bugger if it does right ?
+ */
+ andi. r10,r8,MSR_EE
+ bne+ 1f
+ stw r3,GPR3(r1)
+ bl trace_hardirqs_off
+ lwz r3,GPR3(r1)
+1:
+#endif /* CONFIG_TRACE_IRQFLAGS */
#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
/* If the process has its own DBCR0 value, load it up. The internal
debug mode bit tells us that dbcr0 should be loaded. */
mtlr r4
mtcr r5
lwz r7,_NIP(r1)
- lwz r8,_MSR(r1)
FIX_SRR1(r8, r0)
lwz r2,GPR2(r1)
lwz r1,GPR1(r1)
andi. r0,r9,(_TIF_SYSCALL_T_OR_A|_TIF_SINGLESTEP)
beq ret_from_except
- /* Re-enable interrupts */
+ /* Re-enable interrupts. There is no need to trace that with
+ * lockdep as we are supposed to have IRQs on at this point
+ */
ori r10,r10,MSR_EE
SYNC
MTMSRD(r10)
/* Hard-disable interrupts so that current_thread_info()->flags
* can't change between when we test it and when we return
* from the interrupt. */
+ /* Note: We don't bother telling lockdep about it */
LOAD_MSR_KERNEL(r10,MSR_KERNEL)
SYNC /* Some chip revs have problems here... */
MTMSRD(r10) /* disable interrupts */
beq+ restore
andi. r0,r3,MSR_EE /* interrupts off? */
beq restore /* don't schedule if so */
+#ifdef CONFIG_TRACE_IRQFLAGS
+ /* Lockdep thinks irqs are enabled, we need to call
+ * preempt_schedule_irq with IRQs off, so we inform lockdep
+ * now that we -did- turn them off already
+ */
+ bl trace_hardirqs_off
+#endif
1: bl preempt_schedule_irq
rlwinm r9,r1,0,0,(31-THREAD_SHIFT)
lwz r3,TI_FLAGS(r9)
andi. r0,r3,_TIF_NEED_RESCHED
bne- 1b
+#ifdef CONFIG_TRACE_IRQFLAGS
+ /* And now, to properly rebalance the above, we tell lockdep they
+ * are being turned back on, which will happen when we return
+ */
+ bl trace_hardirqs_on
+#endif
#else
resume_kernel:
#endif /* CONFIG_PREEMPT */
stw r6,icache_44x_need_flush@l(r4)
1:
#endif /* CONFIG_44x */
+
+ lwz r9,_MSR(r1)
+#ifdef CONFIG_TRACE_IRQFLAGS
+ /* Lockdep doesn't know about the fact that IRQs are temporarily turned
+ * off in this assembly code while peeking at TI_FLAGS() and such. However
+ * we need to inform it if the exception turned interrupts off, and we
+ * are about to trun them back on.
+ *
+ * The problem here sadly is that we don't know whether the exceptions was
+ * one that turned interrupts off or not. So we always tell lockdep about
+ * turning them on here when we go back to wherever we came from with EE
+ * on, even if that may meen some redudant calls being tracked. Maybe later
+ * we could encode what the exception did somewhere or test the exception
+ * type in the pt_regs but that sounds overkill
+ */
+ andi. r10,r9,MSR_EE
+ beq 1f
+ bl trace_hardirqs_on
+ lwz r9,_MSR(r1)
+1:
+#endif /* CONFIG_TRACE_IRQFLAGS */
+
lwz r0,GPR0(r1)
lwz r2,GPR2(r1)
REST_4GPRS(3, r1)
stwcx. r0,0,r1 /* to clear the reservation */
#if !(defined(CONFIG_4xx) || defined(CONFIG_BOOKE))
- lwz r9,_MSR(r1)
andi. r10,r9,MSR_RI /* check if this exception occurred */
beql nonrecoverable /* at a bad place (MSR:RI = 0) */
MTMSRD(r10) /* clear the RI bit */
.globl exc_exit_restart
exc_exit_restart:
- lwz r9,_MSR(r1)
lwz r12,_NIP(r1)
FIX_SRR1(r9,r10)
mtspr SPRN_SRR0,r12
beq do_user_signal
do_resched: /* r10 contains MSR_KERNEL here */
+ /* Note: We don't need to inform lockdep that we are enabling
+ * interrupts here. As far as it knows, they are already enabled
+ */
ori r10,r10,MSR_EE
SYNC
MTMSRD(r10) /* hard-enable interrupts */
bl schedule
recheck:
+ /* Note: And we don't tell it we are disabling them again
+ * neither. Those disable/enable cycles used to peek at
+ * TI_FLAGS aren't advertised.
+ */
LOAD_MSR_KERNEL(r10,MSR_KERNEL)
SYNC
MTMSRD(r10) /* disable interrupts */
RFI
/*
- * Use the first pair of BAT registers to map the 1st 16MB
- * of RAM to PAGE_OFFSET. From this point on we can't safely
- * call OF any more.
+ * On 601, we use 3 BATs to map up to 24M of RAM at _PAGE_OFFSET
+ * (we keep one for debugging) and on others, we use one 256M BAT.
*/
initial_bats:
lis r11,PAGE_OFFSET@h
bne 4f
ori r11,r11,4 /* set up BAT registers for 601 */
li r8,0x7f /* valid, block length = 8MB */
- oris r9,r11,0x800000@h /* set up BAT reg for 2nd 8M */
- oris r10,r8,0x800000@h /* set up BAT reg for 2nd 8M */
mtspr SPRN_IBAT0U,r11 /* N.B. 601 has valid bit in */
mtspr SPRN_IBAT0L,r8 /* lower BAT register */
- mtspr SPRN_IBAT1U,r9
- mtspr SPRN_IBAT1L,r10
+ addis r11,r11,0x800000@h
+ addis r8,r8,0x800000@h
+ mtspr SPRN_IBAT1U,r11
+ mtspr SPRN_IBAT1L,r8
+ addis r11,r11,0x800000@h
+ addis r8,r8,0x800000@h
+ mtspr SPRN_IBAT2U,r11
+ mtspr SPRN_IBAT2L,r8
isync
blr
dev->dev.archdata.of_node = np;
if (bus_id)
- dev_set_name(&dev->dev, bus_id);
+ dev_set_name(&dev->dev, "%s", bus_id);
else
of_device_make_bus_id(dev);
for (i = 0; i < 32; i++) {
if ((i % REGS_PER_LINE) == 0)
- printk("\n" KERN_INFO "GPR%02d: ", i);
+ printk("\nGPR%02d: ", i);
printk(REG " ", regs->gpr[i]);
if (i == LAST_VOLATILE && !FULL_REGS(regs))
break;
#include <asm/syscalls.h>
#include <asm/smp.h>
#include <asm/atomic.h>
+#include <asm/time.h>
struct rtas_t rtas = {
- .lock = SPIN_LOCK_UNLOCKED
+ .lock = __RAW_SPIN_LOCK_UNLOCKED
};
EXPORT_SYMBOL(rtas);
void (*rtas_flash_term_hook)(int);
EXPORT_SYMBOL(rtas_flash_term_hook);
+/* RTAS use home made raw locking instead of spin_lock_irqsave
+ * because those can be called from within really nasty contexts
+ * such as having the timebase stopped which would lockup with
+ * normal locks and spinlock debugging enabled
+ */
+static unsigned long lock_rtas(void)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ preempt_disable();
+ __raw_spin_lock_flags(&rtas.lock, flags);
+ return flags;
+}
+
+static void unlock_rtas(unsigned long flags)
+{
+ __raw_spin_unlock(&rtas.lock);
+ local_irq_restore(flags);
+ preempt_enable();
+}
+
/*
* call_rtas_display_status and call_rtas_display_status_delay
* are designed only for very early low-level debugging, which
if (!rtas.base)
return;
- spin_lock_irqsave(&rtas.lock, s);
+ s = lock_rtas();
args->token = 10;
args->nargs = 1;
enter_rtas(__pa(args));
- spin_unlock_irqrestore(&rtas.lock, s);
+ unlock_rtas(s);
}
static void call_rtas_display_status_delay(char c)
if (!rtas.entry || token == RTAS_UNKNOWN_SERVICE)
return -1;
- /* Gotta do something different here, use global lock for now... */
- spin_lock_irqsave(&rtas.lock, s);
+ s = lock_rtas();
rtas_args = &rtas.args;
rtas_args->token = token;
outputs[i] = rtas_args->rets[i+1];
ret = (nret > 0)? rtas_args->rets[0]: 0;
- /* Gotta do something different here, use global lock for now... */
- spin_unlock_irqrestore(&rtas.lock, s);
+ unlock_rtas(s);
if (buff_copy) {
log_error(buff_copy, ERR_TYPE_RTAS_LOG, 0);
buff_copy = get_errorlog_buffer();
- spin_lock_irqsave(&rtas.lock, flags);
+ flags = lock_rtas();
rtas.args = args;
enter_rtas(__pa(&rtas.args));
if (args.rets[0] == -1)
errbuf = __fetch_rtas_last_error(buff_copy);
- spin_unlock_irqrestore(&rtas.lock, flags);
+ unlock_rtas(flags);
if (buff_copy) {
if (errbuf)
/* break now */
return 1;
}
+
+static raw_spinlock_t timebase_lock;
+static u64 timebase = 0;
+
+void __cpuinit rtas_give_timebase(void)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ hard_irq_disable();
+ __raw_spin_lock(&timebase_lock);
+ rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL);
+ timebase = get_tb();
+ __raw_spin_unlock(&timebase_lock);
+
+ while (timebase)
+ barrier();
+ rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL);
+ local_irq_restore(flags);
+}
+
+void __cpuinit rtas_take_timebase(void)
+{
+ while (!timebase)
+ barrier();
+ __raw_spin_lock(&timebase_lock);
+ set_tb(timebase >> 32, timebase & 0xffffffff);
+ timebase = 0;
+ __raw_spin_unlock(&timebase_lock);
+}
*/
notrace void __init machine_init(unsigned long dt_ptr)
{
+ lockdep_init();
+
/* Enable early debugging if any specified (see udbg.h) */
udbg_early_init();
/* SMP operations for this machine */
struct smp_ops_t *smp_ops;
-static volatile unsigned int cpu_callin_map[NR_CPUS];
+/* Can't be static due to PowerMac hackery */
+volatile unsigned int cpu_callin_map[NR_CPUS];
int smt_enabled_at_boot = 1;
#ifdef CONFIG_PPC_EARLY_DEBUG_44x
#include <platforms/44x/44x.h>
-static int udbg_44x_as1_flush(void)
+static void udbg_44x_as1_flush(void)
{
if (udbg_comport) {
while ((as1_readb(&udbg_comport->lsr) & LSR_THRE) == 0)
obj-$(CONFIG_HUGETLB_PAGE) += hugetlbpage.o
obj-$(CONFIG_PPC_SUBPAGE_PROT) += subpage-prot.o
obj-$(CONFIG_NOT_COHERENT_CACHE) += dma-noncoherent.o
+obj-$(CONFIG_HIGHMEM) += highmem.o
--- /dev/null
+/*
+ * highmem.c: virtual kernel memory mappings for high memory
+ *
+ * PowerPC version, stolen from the i386 version.
+ *
+ * Used in CONFIG_HIGHMEM systems for memory pages which
+ * are not addressable by direct kernel virtual addresses.
+ *
+ * Copyright (C) 1999 Gerhard Wichert, Siemens AG
+ * Gerhard.Wichert@pdb.siemens.de
+ *
+ *
+ * Redesigned the x86 32-bit VM architecture to deal with
+ * up to 16 Terrabyte physical memory. With current x86 CPUs
+ * we now support up to 64 Gigabytes physical RAM.
+ *
+ * Copyright (C) 1999 Ingo Molnar <mingo@redhat.com>
+ *
+ * Reworked for PowerPC by various contributors. Moved from
+ * highmem.h by Benjamin Herrenschmidt (c) 2009 IBM Corp.
+ */
+
+#include <linux/highmem.h>
+#include <linux/module.h>
+
+/*
+ * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap
+ * gives a more generic (and caching) interface. But kmap_atomic can
+ * be used in IRQ contexts, so in some (very limited) cases we need
+ * it.
+ */
+void *kmap_atomic_prot(struct page *page, enum km_type type, pgprot_t prot)
+{
+ unsigned int idx;
+ unsigned long vaddr;
+
+ /* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */
+ pagefault_disable();
+ if (!PageHighMem(page))
+ return page_address(page);
+
+ debug_kmap_atomic(type);
+ idx = type + KM_TYPE_NR*smp_processor_id();
+ vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx);
+#ifdef CONFIG_DEBUG_HIGHMEM
+ BUG_ON(!pte_none(*(kmap_pte-idx)));
+#endif
+ __set_pte_at(&init_mm, vaddr, kmap_pte-idx, mk_pte(page, prot), 1);
+ local_flush_tlb_page(NULL, vaddr);
+
+ return (void*) vaddr;
+}
+EXPORT_SYMBOL(kmap_atomic_prot);
+
+void kunmap_atomic(void *kvaddr, enum km_type type)
+{
+#ifdef CONFIG_DEBUG_HIGHMEM
+ unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK;
+ enum fixed_addresses idx = type + KM_TYPE_NR*smp_processor_id();
+
+ if (vaddr < __fix_to_virt(FIX_KMAP_END)) {
+ pagefault_enable();
+ return;
+ }
+
+ BUG_ON(vaddr != __fix_to_virt(FIX_KMAP_BEGIN + idx));
+
+ /*
+ * force other mappings to Oops if they'll try to access
+ * this pte without first remap it
+ */
+ pte_clear(&init_mm, vaddr, kmap_pte-idx);
+ local_flush_tlb_page(NULL, vaddr);
+#endif
+ pagefault_enable();
+}
+EXPORT_SYMBOL(kunmap_atomic);
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/of_gpio.h>
+#include <linux/of_i2c.h>
#include <asm/machdep.h>
#include <asm/prom.h>
static u32 post_info;
-/* I am not sure this is the best place for this... */
static int __init warp_post_info(void)
{
struct device_node *np;
return 0;
}
-static void pika_setup_critical_temp(struct i2c_client *client)
+static void pika_setup_critical_temp(struct device_node *np,
+ struct i2c_client *client)
{
- struct device_node *np;
int irq, rc;
/* Do this before enabling critical temp interrupt since we
i2c_smbus_write_byte_data(client, 2, 65); /* Thigh */
i2c_smbus_write_byte_data(client, 3, 0); /* Tlow */
- np = of_find_compatible_node(NULL, NULL, "adi,ad7414");
- if (np == NULL) {
- printk(KERN_ERR __FILE__ ": Unable to find ad7414\n");
- return;
- }
-
irq = irq_of_parse_and_map(np, 0);
- of_node_put(np);
if (irq == NO_IRQ) {
printk(KERN_ERR __FILE__ ": Unable to get ad7414 irq\n");
return;
static int pika_dtm_thread(void __iomem *fpga)
{
- struct i2c_adapter *adap;
+ struct device_node *np;
struct i2c_client *client;
- /* We loop in case either driver was compiled as a module and
- * has not been insmoded yet.
- */
- while (!(adap = i2c_get_adapter(0))) {
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(HZ);
- }
-
- while (1) {
- list_for_each_entry(client, &adap->clients, list)
- if (client->addr == 0x4a)
- goto found_it;
+ np = of_find_compatible_node(NULL, NULL, "adi,ad7414");
+ if (np == NULL)
+ return -ENOENT;
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(HZ);
+ client = of_find_i2c_device_by_node(np);
+ if (client == NULL) {
+ of_node_put(np);
+ return -ENOENT;
}
-found_it:
- pika_setup_critical_temp(client);
+ pika_setup_critical_temp(np, client);
- i2c_put_adapter(adap);
+ of_node_put(np);
- printk(KERN_INFO "PIKA DTM thread running.\n");
+ printk(KERN_INFO "Warp DTM thread running.\n");
while (!kthread_should_stop()) {
int val;
return 0;
}
-
static int __init pika_dtm_start(void)
{
struct task_struct *dtm_thread;
{ .type = "qe", },
{ .compatible = "fsl,qe", },
{ .compatible = "gianfar", },
+ { .compatible = "fsl,rapidio-delta", },
{},
};
pr_debug("smp_85xx_kick_cpu: kick CPU #%d\n", nr);
- local_irq_save(flags);
-
np = of_get_cpu_node(nr, NULL);
cpu_rel_addr = of_get_property(np, "cpu-release-addr", NULL);
if (cpu_rel_addr == NULL) {
printk(KERN_ERR "No cpu-release-addr for cpu %d\n", nr);
- local_irq_restore(flags);
return;
}
/* Map the spin table */
bptr_vaddr = ioremap(*cpu_rel_addr, SIZE_BOOT_ENTRY);
+ local_irq_save(flags);
+
out_be32(bptr_vaddr + BOOT_ENTRY_PIR, nr);
out_be32(bptr_vaddr + BOOT_ENTRY_ADDR_LOWER, __pa(__early_start));
while ((__secondary_hold_acknowledge != nr) && (++n < 1000))
mdelay(1);
- iounmap(bptr_vaddr);
-
local_irq_restore(flags);
+ iounmap(bptr_vaddr);
+
pr_debug("waited %d msecs for CPU #%d.\n", n, nr);
}
{},
};
-static void __init socrates_init(void)
+static int __init socrates_publish_devices(void)
{
- of_platform_bus_probe(NULL, socrates_of_bus_ids, NULL);
+ return of_platform_bus_probe(NULL, socrates_of_bus_ids, NULL);
}
+machine_device_initcall(socrates, socrates_publish_devices);
/*
* Called very early, device-tree isn't unflattened
.name = "Socrates",
.probe = socrates_probe,
.setup_arch = socrates_setup_arch,
- .init = socrates_init,
.init_IRQ = socrates_pic_init,
.get_irq = mpic_get_irq,
.restart = fsl_rstcr_restart,
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
-#include <linux/of_platform.h>
/* A few bit definitions needed for fixups on some boards */
#define MPC85xx_L2CTL_L2E 0x80000000 /* L2 enable */
#include <asm/prom.h>
#include <asm/smp.h>
#include <asm/paca.h>
-#include <asm/time.h>
#include <asm/machdep.h>
#include <asm/cputable.h>
#include <asm/firmware.h>
mtspr(SPRN_DABRX, DABRX_KERNEL | DABRX_USER);
}
-static DEFINE_SPINLOCK(timebase_lock);
-static unsigned long timebase = 0;
-
-static void __devinit cell_give_timebase(void)
-{
- spin_lock(&timebase_lock);
- rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL);
- timebase = get_tb();
- spin_unlock(&timebase_lock);
-
- while (timebase)
- barrier();
- rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL);
-}
-
-static void __devinit cell_take_timebase(void)
-{
- while (!timebase)
- barrier();
- spin_lock(&timebase_lock);
- set_tb(timebase >> 32, timebase & 0xffffffff);
- timebase = 0;
- spin_unlock(&timebase_lock);
-}
-
static void __devinit smp_cell_kick_cpu(int nr)
{
BUG_ON(nr < 0 || nr >= NR_CPUS);
/* Non-lpar has additional take/give timebase */
if (rtas_token("freeze-time-base") != RTAS_UNKNOWN_SERVICE) {
- smp_ops->give_timebase = cell_give_timebase;
- smp_ops->take_timebase = cell_take_timebase;
+ smp_ops->give_timebase = rtas_give_timebase;
+ smp_ops->take_timebase = rtas_take_timebase;
}
DBG(" <- smp_init_cell()\n");
#include <asm/io.h>
#include <asm/prom.h>
#include <asm/smp.h>
-#include <asm/time.h>
#include <asm/machdep.h>
#include <asm/mpic.h>
#include <asm/rtas.h>
mpic_setup_this_cpu();
}
-static DEFINE_SPINLOCK(timebase_lock);
-static unsigned int timebase_upper = 0, timebase_lower = 0;
-
-void __devinit smp_chrp_give_timebase(void)
-{
- spin_lock(&timebase_lock);
- rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL);
- timebase_upper = get_tbu();
- timebase_lower = get_tbl();
- spin_unlock(&timebase_lock);
-
- while (timebase_upper || timebase_lower)
- barrier();
- rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL);
-}
-
-void __devinit smp_chrp_take_timebase(void)
-{
- while (!(timebase_upper || timebase_lower))
- barrier();
- spin_lock(&timebase_lock);
- set_tb(timebase_upper, timebase_lower);
- timebase_upper = 0;
- timebase_lower = 0;
- spin_unlock(&timebase_lock);
- printk("CPU %i taken timebase\n", smp_processor_id());
-}
-
/* CHRP with openpic */
struct smp_ops_t chrp_smp_ops = {
.message_pass = smp_mpic_message_pass,
.probe = smp_mpic_probe,
.kick_cpu = smp_chrp_kick_cpu,
.setup_cpu = smp_chrp_setup_cpu,
- .give_timebase = smp_chrp_give_timebase,
- .take_timebase = smp_chrp_take_timebase,
+ .give_timebase = rtas_give_timebase,
+ .take_timebase = rtas_take_timebase,
};
}
#ifdef CONFIG_SMP
-static DEFINE_SPINLOCK(timebase_lock);
+static raw_spinlock_t timebase_lock;
static unsigned long timebase;
static void __devinit pas_give_timebase(void)
{
- spin_lock(&timebase_lock);
+ unsigned long flags;
+
+ local_irq_save(flags);
+ hard_irq_disable();
+ __raw_spin_lock(&timebase_lock);
mtspr(SPRN_TBCTL, TBCTL_FREEZE);
isync();
timebase = get_tb();
- spin_unlock(&timebase_lock);
+ __raw_spin_unlock(&timebase_lock);
while (timebase)
barrier();
mtspr(SPRN_TBCTL, TBCTL_RESTART);
+ local_irq_restore(flags);
}
static void __devinit pas_take_timebase(void)
while (!timebase)
smp_rmb();
- spin_lock(&timebase_lock);
+ __raw_spin_lock(&timebase_lock);
set_tb(timebase >> 32, timebase & 0xffffffff);
timebase = 0;
- spin_unlock(&timebase_lock);
+ __raw_spin_unlock(&timebase_lock);
}
struct smp_ops_t pas_smp_ops = {
EXPORT_SYMBOL(smu_cmdbuf_abs);
#endif
-#ifdef CONFIG_SMP
-extern struct smp_ops_t psurge_smp_ops;
-extern struct smp_ops_t core99_smp_ops;
-#endif /* CONFIG_SMP */
-
static void pmac_show_cpuinfo(struct seq_file *m)
{
struct device_node *np;
ROOT_DEV = DEFAULT_ROOT_DEVICE;
#endif
-#ifdef CONFIG_SMP
- /* Check for Core99 */
- ic = of_find_node_by_name(NULL, "uni-n");
- if (!ic)
- ic = of_find_node_by_name(NULL, "u3");
- if (!ic)
- ic = of_find_node_by_name(NULL, "u4");
- if (ic) {
- of_node_put(ic);
- smp_ops = &core99_smp_ops;
- }
-#ifdef CONFIG_PPC32
- else {
- /*
- * We have to set bits in cpu_possible_map here since the
- * secondary CPU(s) aren't in the device tree, and
- * setup_per_cpu_areas only allocates per-cpu data for
- * CPUs in the cpu_possible_map.
- */
- int cpu;
-
- for (cpu = 1; cpu < 4 && cpu < NR_CPUS; ++cpu)
- cpu_set(cpu, cpu_possible_map);
- smp_ops = &psurge_smp_ops;
- }
-#endif
-#endif /* CONFIG_SMP */
-
#ifdef CONFIG_ADB
if (strstr(cmd_line, "adb_sync")) {
extern int __adb_probe_sync;
#ifdef CONFIG_PPC64
iommu_init_early_dart();
#endif
+
+ /* SMP Init has to be done early as we need to patch up
+ * cpu_possible_map before interrupt stacks are allocated
+ * or kaboom...
+ */
+#ifdef CONFIG_SMP
+ pmac_setup_smp();
+#endif
}
static int __init pmac_declare_of_platform_devices(void)
extern void __secondary_start_pmac_0(void);
extern int pmac_pfunc_base_install(void);
-#ifdef CONFIG_PPC32
+static void (*pmac_tb_freeze)(int freeze);
+static u64 timebase;
+static int tb_req;
-/* Sync flag for HW tb sync */
-static volatile int sec_tb_reset = 0;
+#ifdef CONFIG_PPC32
/*
* Powersurge (old powermac SMP) support.
psurge_quad_init();
/* All released cards using this HW design have 4 CPUs */
ncpus = 4;
+ /* No sure how timebase sync works on those, let's use SW */
+ smp_ops->give_timebase = smp_generic_give_timebase;
+ smp_ops->take_timebase = smp_generic_take_timebase;
} else {
iounmap(quad_base);
if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) {
psurge_start = ioremap(PSURGE_START, 4);
psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4);
- /*
- * This is necessary because OF doesn't know about the
+ /* This is necessary because OF doesn't know about the
* secondary cpu(s), and thus there aren't nodes in the
* device tree for them, and smp_setup_cpu_maps hasn't
- * set their bits in cpu_possible_map and cpu_present_map.
+ * set their bits in cpu_present_map.
*/
if (ncpus > NR_CPUS)
ncpus = NR_CPUS;
- for (i = 1; i < ncpus ; ++i) {
+ for (i = 1; i < ncpus ; ++i)
cpu_set(i, cpu_present_map);
- set_hard_smp_processor_id(i, i);
- }
if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352);
static void __init smp_psurge_kick_cpu(int nr)
{
unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8;
- unsigned long a;
- int i;
+ unsigned long a, flags;
+ int i, j;
+
+ /* Defining this here is evil ... but I prefer hiding that
+ * crap to avoid giving people ideas that they can do the
+ * same.
+ */
+ extern volatile unsigned int cpu_callin_map[NR_CPUS];
/* may need to flush here if secondary bats aren't setup */
for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32)
if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353);
+ /* This is going to freeze the timeebase, we disable interrupts */
+ local_irq_save(flags);
+
out_be32(psurge_start, start);
mb();
psurge_set_ipi(nr);
+
/*
* We can't use udelay here because the timebase is now frozen.
*/
for (i = 0; i < 2000; ++i)
- barrier();
+ asm volatile("nop" : : : "memory");
psurge_clr_ipi(nr);
- if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354);
-}
-
-/*
- * With the dual-cpu powersurge board, the decrementers and timebases
- * of both cpus are frozen after the secondary cpu is started up,
- * until we give the secondary cpu another interrupt. This routine
- * uses this to get the timebases synchronized.
- * -- paulus.
- */
-static void __init psurge_dual_sync_tb(int cpu_nr)
-{
- int t;
-
- set_dec(tb_ticks_per_jiffy);
- /* XXX fixme */
- set_tb(0, 0);
-
- if (cpu_nr > 0) {
+ /*
+ * Also, because the timebase is frozen, we must not return to the
+ * caller which will try to do udelay's etc... Instead, we wait -here-
+ * for the CPU to callin.
+ */
+ for (i = 0; i < 100000 && !cpu_callin_map[nr]; ++i) {
+ for (j = 1; j < 10000; j++)
+ asm volatile("nop" : : : "memory");
+ asm volatile("sync" : : : "memory");
+ }
+ if (!cpu_callin_map[nr])
+ goto stuck;
+
+ /* And we do the TB sync here too for standard dual CPU cards */
+ if (psurge_type == PSURGE_DUAL) {
+ while(!tb_req)
+ barrier();
+ tb_req = 0;
+ mb();
+ timebase = get_tb();
+ mb();
+ while (timebase)
+ barrier();
mb();
- sec_tb_reset = 1;
- return;
}
+ stuck:
+ /* now interrupt the secondary, restarting both TBs */
+ if (psurge_type == PSURGE_DUAL)
+ psurge_set_ipi(1);
- /* wait for the secondary to have reset its TB before proceeding */
- for (t = 10000000; t > 0 && !sec_tb_reset; --t)
- ;
-
- /* now interrupt the secondary, starting both TBs */
- psurge_set_ipi(1);
+ if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354);
}
static struct irqaction psurge_irqaction = {
static void __init smp_psurge_setup_cpu(int cpu_nr)
{
+ if (cpu_nr != 0)
+ return;
- if (cpu_nr == 0) {
- /* If we failed to start the second CPU, we should still
- * send it an IPI to start the timebase & DEC or we might
- * have them stuck.
- */
- if (num_online_cpus() < 2) {
- if (psurge_type == PSURGE_DUAL)
- psurge_set_ipi(1);
- return;
- }
- /* reset the entry point so if we get another intr we won't
- * try to startup again */
- out_be32(psurge_start, 0x100);
- if (setup_irq(30, &psurge_irqaction))
- printk(KERN_ERR "Couldn't get primary IPI interrupt");
- }
-
- if (psurge_type == PSURGE_DUAL)
- psurge_dual_sync_tb(cpu_nr);
+ /* reset the entry point so if we get another intr we won't
+ * try to startup again */
+ out_be32(psurge_start, 0x100);
+ if (setup_irq(30, &psurge_irqaction))
+ printk(KERN_ERR "Couldn't get primary IPI interrupt");
}
void __init smp_psurge_take_timebase(void)
{
- /* Dummy implementation */
+ if (psurge_type != PSURGE_DUAL)
+ return;
+
+ tb_req = 1;
+ mb();
+ while (!timebase)
+ barrier();
+ mb();
+ set_tb(timebase >> 32, timebase & 0xffffffff);
+ timebase = 0;
+ mb();
+ set_dec(tb_ticks_per_jiffy/2);
}
void __init smp_psurge_give_timebase(void)
{
- /* Dummy implementation */
+ /* Nothing to do here */
}
/* PowerSurge-style Macs */
* Core 99 and later support
*/
-static void (*pmac_tb_freeze)(int freeze);
-static u64 timebase;
-static int tb_req;
static void smp_core99_give_timebase(void)
{
set_tb(timebase >> 32, timebase & 0xffffffff);
timebase = 0;
mb();
- set_dec(tb_ticks_per_jiffy/2);
local_irq_restore(flags);
}
# endif
#endif
};
+
+void __init pmac_setup_smp(void)
+{
+ struct device_node *np;
+
+ /* Check for Core99 */
+ np = of_find_node_by_name(NULL, "uni-n");
+ if (!np)
+ np = of_find_node_by_name(NULL, "u3");
+ if (!np)
+ np = of_find_node_by_name(NULL, "u4");
+ if (np) {
+ of_node_put(np);
+ smp_ops = &core99_smp_ops;
+ }
+#ifdef CONFIG_PPC32
+ else {
+ /* We have to set bits in cpu_possible_map here since the
+ * secondary CPU(s) aren't in the device tree. Various
+ * things won't be initialized for CPUs not in the possible
+ * map, so we really need to fix it up here.
+ */
+ int cpu;
+
+ for (cpu = 1; cpu < 4 && cpu < NR_CPUS; ++cpu)
+ cpu_set(cpu, cpu_possible_map);
+ smp_ops = &psurge_smp_ops;
+ }
+#endif /* CONFIG_PPC32 */
+}
+
#include <asm/prom.h>
#include <asm/smp.h>
#include <asm/paca.h>
-#include <asm/time.h>
#include <asm/machdep.h>
#include <asm/cputable.h>
#include <asm/firmware.h>
}
#endif /* CONFIG_XICS */
-static DEFINE_SPINLOCK(timebase_lock);
-static unsigned long timebase = 0;
-
-static void __devinit pSeries_give_timebase(void)
-{
- spin_lock(&timebase_lock);
- rtas_call(rtas_token("freeze-time-base"), 0, 1, NULL);
- timebase = get_tb();
- spin_unlock(&timebase_lock);
-
- while (timebase)
- barrier();
- rtas_call(rtas_token("thaw-time-base"), 0, 1, NULL);
-}
-
-static void __devinit pSeries_take_timebase(void)
-{
- while (!timebase)
- barrier();
- spin_lock(&timebase_lock);
- set_tb(timebase >> 32, timebase & 0xffffffff);
- timebase = 0;
- spin_unlock(&timebase_lock);
-}
-
static void __devinit smp_pSeries_kick_cpu(int nr)
{
BUG_ON(nr < 0 || nr >= NR_CPUS);
/* Non-lpar has additional take/give timebase */
if (rtas_token("freeze-time-base") != RTAS_UNKNOWN_SERVICE) {
- smp_ops->give_timebase = pSeries_give_timebase;
- smp_ops->take_timebase = pSeries_take_timebase;
+ smp_ops->give_timebase = rtas_give_timebase;
+ smp_ops->take_timebase = rtas_take_timebase;
}
pr_debug(" <- smp_init_pSeries()\n");
}
#ifdef CONFIG_PPC_DCR
-static void _mpic_map_dcr(struct mpic *mpic, struct mpic_reg_bank *rb,
+static void _mpic_map_dcr(struct mpic *mpic, struct device_node *node,
+ struct mpic_reg_bank *rb,
unsigned int offset, unsigned int size)
{
const u32 *dbasep;
- dbasep = of_get_property(mpic->irqhost->of_node, "dcr-reg", NULL);
+ dbasep = of_get_property(node, "dcr-reg", NULL);
- rb->dhost = dcr_map(mpic->irqhost->of_node, *dbasep + offset, size);
+ rb->dhost = dcr_map(node, *dbasep + offset, size);
BUG_ON(!DCR_MAP_OK(rb->dhost));
}
-static inline void mpic_map(struct mpic *mpic, phys_addr_t phys_addr,
- struct mpic_reg_bank *rb, unsigned int offset,
- unsigned int size)
+static inline void mpic_map(struct mpic *mpic, struct device_node *node,
+ phys_addr_t phys_addr, struct mpic_reg_bank *rb,
+ unsigned int offset, unsigned int size)
{
if (mpic->flags & MPIC_USES_DCR)
- _mpic_map_dcr(mpic, rb, offset, size);
+ _mpic_map_dcr(mpic, node, rb, offset, size);
else
_mpic_map_mmio(mpic, phys_addr, rb, offset, size);
}
#else /* CONFIG_PPC_DCR */
-#define mpic_map(m,p,b,o,s) _mpic_map_mmio(m,p,b,o,s)
+#define mpic_map(m,n,p,b,o,s) _mpic_map_mmio(m,p,b,o,s)
#endif /* !CONFIG_PPC_DCR */
int intvec_top;
u64 paddr = phys_addr;
- mpic = alloc_bootmem(sizeof(struct mpic));
+ mpic = kzalloc(sizeof(struct mpic), GFP_KERNEL);
if (mpic == NULL)
return NULL;
-
- memset(mpic, 0, sizeof(struct mpic));
+
mpic->name = name;
mpic->hc_irq = mpic_irq_chip;
}
/* Map the global registers */
- mpic_map(mpic, paddr, &mpic->gregs, MPIC_INFO(GREG_BASE), 0x1000);
- mpic_map(mpic, paddr, &mpic->tmregs, MPIC_INFO(TIMER_BASE), 0x1000);
+ mpic_map(mpic, node, paddr, &mpic->gregs, MPIC_INFO(GREG_BASE), 0x1000);
+ mpic_map(mpic, node, paddr, &mpic->tmregs, MPIC_INFO(TIMER_BASE), 0x1000);
/* Reset */
if (flags & MPIC_WANTS_RESET) {
/* Map the per-CPU registers */
for (i = 0; i < mpic->num_cpus; i++) {
- mpic_map(mpic, paddr, &mpic->cpuregs[i],
+ mpic_map(mpic, node, paddr, &mpic->cpuregs[i],
MPIC_INFO(CPU_BASE) + i * MPIC_INFO(CPU_STRIDE),
0x1000);
}
/* Initialize main ISU if none provided */
if (mpic->isu_size == 0) {
mpic->isu_size = mpic->num_sources;
- mpic_map(mpic, paddr, &mpic->isus[0],
+ mpic_map(mpic, node, paddr, &mpic->isus[0],
MPIC_INFO(IRQ_BASE), MPIC_INFO(IRQ_STRIDE) * mpic->isu_size);
}
mpic->isu_shift = 1 + __ilog2(mpic->isu_size - 1);
BUG_ON(isu_num >= MPIC_MAX_ISU);
- mpic_map(mpic, paddr, &mpic->isus[isu_num], 0,
+ mpic_map(mpic, mpic->irqhost->of_node,
+ paddr, &mpic->isus[isu_num], 0,
MPIC_INFO(IRQ_STRIDE) * mpic->isu_size);
+
if ((isu_first + mpic->isu_size) > mpic->num_sources)
mpic->num_sources = isu_first + mpic->isu_size;
}
{
unsigned long flags;
u8 mcn_shift = 0, dev_shift = 0;
+ u32 ret;
spin_lock_irqsave(&qe_lock, flags);
if (cmd == QE_RESET) {
}
/* wait for the QE_CR_FLG to clear */
- while(in_be32(&qe_immr->cp.cecr) & QE_CR_FLG)
- cpu_relax();
+ ret = spin_event_timeout((in_be32(&qe_immr->cp.cecr) & QE_CR_FLG) == 0,
+ 100, 0);
+ /* On timeout (e.g. failure), the expression will be false (ret == 0),
+ otherwise it will be true (ret == 1). */
spin_unlock_irqrestore(&qe_lock, flags);
- return 0;
+ return ret == 1;
}
EXPORT_SYMBOL(qe_issue_cmd);
__u8 reservedd0[48]; /* 0x00d0 */
__u64 gcr[16]; /* 0x0100 */
__u64 gbea; /* 0x0180 */
- __u8 reserved188[120]; /* 0x0188 */
+ __u8 reserved188[24]; /* 0x0188 */
+ __u32 fac; /* 0x01a0 */
+ __u8 reserved1a4[92]; /* 0x01a4 */
} __attribute__((packed));
struct kvm_vcpu_stat {
#include <asm/lowcore.h>
#include <asm/pgtable.h>
#include <asm/nmi.h>
+#include <asm/system.h>
#include "kvm-s390.h"
#include "gaccess.h"
{ NULL }
};
+static unsigned long long *facilities;
/* Section: not file related */
void kvm_arch_hardware_enable(void *garbage)
vcpu->arch.sie_block->gmsor = vcpu->kvm->arch.guest_origin;
vcpu->arch.sie_block->ecb = 2;
vcpu->arch.sie_block->eca = 0xC1002001U;
+ vcpu->arch.sie_block->fac = (int) (long) facilities;
hrtimer_init(&vcpu->arch.ckc_timer, CLOCK_REALTIME, HRTIMER_MODE_ABS);
tasklet_init(&vcpu->arch.tasklet, kvm_s390_tasklet,
(unsigned long) vcpu);
static int __init kvm_s390_init(void)
{
- return kvm_init(NULL, sizeof(struct kvm_vcpu), THIS_MODULE);
+ int ret;
+ ret = kvm_init(NULL, sizeof(struct kvm_vcpu), THIS_MODULE);
+ if (ret)
+ return ret;
+
+ /*
+ * guests can ask for up to 255+1 double words, we need a full page
+ * to hold the maximum amount of facilites. On the other hand, we
+ * only set facilities that are known to work in KVM.
+ */
+ facilities = (unsigned long long *) get_zeroed_page(GFP_DMA);
+ if (!facilities) {
+ kvm_exit();
+ return -ENOMEM;
+ }
+ stfle(facilities, 1);
+ facilities[0] &= 0xff00fff3f0700000ULL;
+ return 0;
}
static void __exit kvm_s390_exit(void)
{
+ free_page((unsigned long) facilities);
kvm_exit();
}
vcpu->stat.instruction_stfl++;
/* only pass the facility bits, which we can handle */
- facility_list &= 0xfe00fff3;
+ facility_list &= 0xff00fff3;
rc = copy_to_guest(vcpu, offsetof(struct _lowcore, stfl_fac_list),
&facility_list, sizeof(facility_list));
ifeq ($(CONFIG_SPARC32),y)
quiet_cmd_piggy = PIGGY $@
- cmd_piggy = $(obj)/piggyback_32 $@ $(obj)/System.map $(ROOT_IMG)
+ cmd_piggy = $(obj)/piggyback_32 $@ System.map $(ROOT_IMG)
quiet_cmd_btfix = BTFIX $@
cmd_btfix = $(OBJDUMP) -x vmlinux | $(obj)/btfixupprep > $@
quiet_cmd_sysmap = SYSMAP $(obj)/System.map
$(obj)/zImage: $(obj)/image
$(call if_changed,strip)
-$(obj)/tftpboot.img: $(obj)/piggyback $(obj)/System.map $(obj)/image FORCE
+$(obj)/tftpboot.img: $(obj)/image $(obj)/piggyback_32 System.map $(ROOT_IMG) FORCE
$(call if_changed,elftoaout)
$(call if_changed,piggy)
$(call if_changed,strip)
@echo ' kernel: $@ is ready'
-$(obj)/tftpboot.img: vmlinux $(obj)/piggyback_64 System.map $(ROOT_IMG) FORCE
+$(obj)/tftpboot.img: $(obj)/image $(obj)/piggyback_64 System.map $(ROOT_IMG) FORCE
$(call if_changed,elftoaout)
$(call if_changed,piggy)
@echo ' kernel: $@ is ready'
int main(int argc,char **argv)
{
static char aout_magic[] = { 0x01, 0x03, 0x01, 0x07 };
- unsigned char buffer[1024], *q, *r;
+ char buffer[1024], *q, *r;
unsigned int i, j, k, start, end, offset;
FILE *map;
struct stat s;
while (fgets (buffer, 1024, map)) {
if (!strcmp (buffer + 8, " T start\n") || !strcmp (buffer + 16, " T start\n"))
start = strtoul (buffer, NULL, 16);
- else if (!strcmp (buffer + 8, " A end\n") || !strcmp (buffer + 16, " A end\n"))
+ else if (!strcmp (buffer + 8, " A _end\n") || !strcmp (buffer + 16, " A _end\n"))
end = strtoul (buffer, NULL, 16);
}
fclose (map);
struct stat s;
int image, tail;
+ start = end = 0;
if (stat (argv[3], &s) < 0) die (argv[3]);
map = fopen (argv[2], "r");
if (!map) die(argv[2]);
#include <linux/delay.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
-#include <linux/bootmem.h>
#include <linux/irq.h>
#include <asm/ptrace.h>
tb->nonresum_qmask);
}
-static void __init alloc_one_mondo(unsigned long *pa_ptr, unsigned long qmask)
-{
- unsigned long size = PAGE_ALIGN(qmask + 1);
- void *p = __alloc_bootmem(size, size, 0);
- if (!p) {
- prom_printf("SUN4V: Error, cannot allocate mondo queue.\n");
- prom_halt();
- }
-
- *pa_ptr = __pa(p);
-}
-
-static void __init alloc_one_kbuf(unsigned long *pa_ptr, unsigned long qmask)
+/* Each queue region must be a power of 2 multiple of 64 bytes in
+ * size. The base real address must be aligned to the size of the
+ * region. Thus, an 8KB queue must be 8KB aligned, for example.
+ */
+static void __init alloc_one_queue(unsigned long *pa_ptr, unsigned long qmask)
{
unsigned long size = PAGE_ALIGN(qmask + 1);
- void *p = __alloc_bootmem(size, size, 0);
+ unsigned long order = get_order(size);
+ unsigned long p;
+ p = __get_free_pages(GFP_KERNEL, order);
if (!p) {
- prom_printf("SUN4V: Error, cannot allocate kbuf page.\n");
+ prom_printf("SUN4V: Error, cannot allocate queue.\n");
prom_halt();
}
static void __init init_cpu_send_mondo_info(struct trap_per_cpu *tb)
{
#ifdef CONFIG_SMP
- void *page;
+ unsigned long page;
BUILD_BUG_ON((NR_CPUS * sizeof(u16)) > (PAGE_SIZE - 64));
- page = alloc_bootmem_pages(PAGE_SIZE);
+ page = get_zeroed_page(GFP_KERNEL);
if (!page) {
prom_printf("SUN4V: Error, cannot allocate cpu mondo page.\n");
prom_halt();
for_each_possible_cpu(cpu) {
struct trap_per_cpu *tb = &trap_block[cpu];
- alloc_one_mondo(&tb->cpu_mondo_pa, tb->cpu_mondo_qmask);
- alloc_one_mondo(&tb->dev_mondo_pa, tb->dev_mondo_qmask);
- alloc_one_mondo(&tb->resum_mondo_pa, tb->resum_qmask);
- alloc_one_kbuf(&tb->resum_kernel_buf_pa, tb->resum_qmask);
- alloc_one_mondo(&tb->nonresum_mondo_pa, tb->nonresum_qmask);
- alloc_one_kbuf(&tb->nonresum_kernel_buf_pa,
- tb->nonresum_qmask);
+ alloc_one_queue(&tb->cpu_mondo_pa, tb->cpu_mondo_qmask);
+ alloc_one_queue(&tb->dev_mondo_pa, tb->dev_mondo_qmask);
+ alloc_one_queue(&tb->resum_mondo_pa, tb->resum_qmask);
+ alloc_one_queue(&tb->resum_kernel_buf_pa, tb->resum_qmask);
+ alloc_one_queue(&tb->nonresum_mondo_pa, tb->nonresum_qmask);
+ alloc_one_queue(&tb->nonresum_kernel_buf_pa,
+ tb->nonresum_qmask);
}
}
kill_prom_timer();
size = sizeof(struct ino_bucket) * NUM_IVECS;
- ivector_table = alloc_bootmem(size);
+ ivector_table = kzalloc(size, GFP_KERNEL);
if (!ivector_table) {
prom_printf("Fatal error, cannot allocate ivector_table\n");
prom_halt();
slip_proto_init(&spri->slip);
- dev->init = NULL;
dev->hard_header_len = 0;
dev->header_ops = NULL;
dev->addr_len = 0;
slip_proto_init(&spri->slip);
- dev->init = NULL;
dev->hard_header_len = 0;
dev->header_ops = NULL;
dev->addr_len = 0;
}
static inline void
-dma_sync_single(struct device *dev, dma_addr_t dma_handle, size_t size,
+dma_sync_single_for_cpu(struct device *dev, dma_addr_t dma_handle, size_t size,
enum dma_data_direction direction)
{
BUG();
}
static inline void
-dma_sync_sg(struct device *dev, struct scatterlist *sg, int nelems,
+dma_sync_sg_for_cpu(struct device *dev, struct scatterlist *sg, int nelems,
enum dma_data_direction direction)
{
BUG();
#ifdef __KERNEL__
-#include <asm/page_types.h>
+#include <asm/pgtable_types.h>
/* Physical address where kernel should be loaded. */
#define LOAD_PHYSICAL_ADDR ((CONFIG_PHYSICAL_START \
& ~(CONFIG_PHYSICAL_ALIGN - 1))
/* Minimum kernel alignment, as a power of two */
-#ifdef CONFIG_x86_64
+#ifdef CONFIG_X86_64
#define MIN_KERNEL_ALIGN_LG2 PMD_SHIFT
#else
-#define MIN_KERNEL_ALIGN_LG2 (PAGE_SHIFT+1)
+#define MIN_KERNEL_ALIGN_LG2 (PAGE_SHIFT + THREAD_ORDER)
#endif
#define MIN_KERNEL_ALIGN (_AC(1, UL) << MIN_KERNEL_ALIGN_LG2)
#else /* ...!ASSEMBLY */
+#include <linux/kernel.h>
#include <linux/stringify.h>
#ifdef CONFIG_SMP
/* We can use this directly for local CPU (faster). */
DECLARE_PER_CPU(unsigned long, this_cpu_off);
+#ifdef CONFIG_NEED_MULTIPLE_NODES
+void *pcpu_lpage_remapped(void *kaddr);
+#else
+static inline void *pcpu_lpage_remapped(void *kaddr)
+{
+ return NULL;
+}
+#endif
+
#endif /* !__ASSEMBLY__ */
#ifdef CONFIG_SMP
{
#ifdef CONFIG_X86_HT
unsigned bits;
+ int cpu = smp_processor_id();
bits = c->x86_coreid_bits;
-
/* Low order bits define the core id (index of core in socket) */
c->cpu_core_id = c->initial_apicid & ((1 << bits)-1);
/* Convert the initial APIC ID into the socket ID */
c->phys_proc_id = c->initial_apicid >> bits;
+ /* use socket ID also for last level cache */
+ per_cpu(cpu_llc_id, cpu) = c->phys_proc_id;
#endif
}
#if defined(CONFIG_NUMA) && defined(CONFIG_X86_64)
numa_add_cpu(smp_processor_id());
#endif
-
- /* Cap the iomem address space to what is addressable on all CPUs */
- iomem_resource.end &= (1ULL << c->x86_phys_bits) - 1;
}
#ifdef CONFIG_X86_64
*n = min(*n*2, (int)round_jiffies_relative(check_interval*HZ));
t->expires = jiffies + *n;
- add_timer(t);
+ add_timer_on(t, smp_processor_id());
}
static void mce_do_trigger(struct work_struct *work)
return;
setup_timer(t, mcheck_timer, smp_processor_id());
t->expires = round_jiffies(jiffies + *n);
- add_timer(t);
+ add_timer_on(t, smp_processor_id());
}
/*
#include "dumpstack.h"
int panic_on_unrecovered_nmi;
+int panic_on_io_nmi;
unsigned int code_bytes = 64;
int kstack_depth_to_print = 3 * STACKSLOTS_PER_LINE;
static int die_counter;
return ret;
}
+#ifdef CONFIG_X86_64
+static void __init init_gbpages(void)
+{
+ if (direct_gbpages && cpu_has_gbpages)
+ printk(KERN_INFO "Using GB pages for direct mapping\n");
+ else
+ direct_gbpages = 0;
+}
+#else
+static inline void init_gbpages(void)
+{
+}
+#endif
+
static void __init reserve_brk(void)
{
if (_brk_end > _brk_start)
reserve_brk();
+ init_gbpages();
+
/* max_pfn_mapped is updated here */
max_low_pfn_mapped = init_memory_mapping(0, max_low_pfn<<PAGE_SHIFT);
max_pfn_mapped = max_low_pfn_mapped;
}
/*
- * Remap allocator
+ * Large page remap allocator
*
* This allocator uses PMD page as unit. A PMD page is allocated for
* each cpu and each is remapped into vmalloc area using PMD mapping.
* better than only using 4k mappings while still being NUMA friendly.
*/
#ifdef CONFIG_NEED_MULTIPLE_NODES
-static size_t pcpur_size __initdata;
-static void **pcpur_ptrs __initdata;
+struct pcpul_ent {
+ unsigned int cpu;
+ void *ptr;
+};
+
+static size_t pcpul_size;
+static struct pcpul_ent *pcpul_map;
+static struct vm_struct pcpul_vm;
-static struct page * __init pcpur_get_page(unsigned int cpu, int pageno)
+static struct page * __init pcpul_get_page(unsigned int cpu, int pageno)
{
size_t off = (size_t)pageno << PAGE_SHIFT;
- if (off >= pcpur_size)
+ if (off >= pcpul_size)
return NULL;
- return virt_to_page(pcpur_ptrs[cpu] + off);
+ return virt_to_page(pcpul_map[cpu].ptr + off);
}
-static ssize_t __init setup_pcpu_remap(size_t static_size)
+static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen)
{
- static struct vm_struct vm;
- size_t ptrs_size, dyn_size;
+ size_t map_size, dyn_size;
unsigned int cpu;
+ int i, j;
ssize_t ret;
- /*
- * If large page isn't supported, there's no benefit in doing
- * this. Also, on non-NUMA, embedding is better.
- *
- * NOTE: disabled for now.
- */
- if (true || !cpu_has_pse || !pcpu_need_numa())
+ if (!chosen) {
+ size_t vm_size = VMALLOC_END - VMALLOC_START;
+ size_t tot_size = num_possible_cpus() * PMD_SIZE;
+
+ /* on non-NUMA, embedding is better */
+ if (!pcpu_need_numa())
+ return -EINVAL;
+
+ /* don't consume more than 20% of vmalloc area */
+ if (tot_size > vm_size / 5) {
+ pr_info("PERCPU: too large chunk size %zuMB for "
+ "large page remap\n", tot_size >> 20);
+ return -EINVAL;
+ }
+ }
+
+ /* need PSE */
+ if (!cpu_has_pse) {
+ pr_warning("PERCPU: lpage allocator requires PSE\n");
return -EINVAL;
+ }
/*
* Currently supports only single page. Supporting multiple
* pages won't be too difficult if it ever becomes necessary.
*/
- pcpur_size = PFN_ALIGN(static_size + PERCPU_MODULE_RESERVE +
+ pcpul_size = PFN_ALIGN(static_size + PERCPU_MODULE_RESERVE +
PERCPU_DYNAMIC_RESERVE);
- if (pcpur_size > PMD_SIZE) {
+ if (pcpul_size > PMD_SIZE) {
pr_warning("PERCPU: static data is larger than large page, "
"can't use large page\n");
return -EINVAL;
}
- dyn_size = pcpur_size - static_size - PERCPU_FIRST_CHUNK_RESERVE;
+ dyn_size = pcpul_size - static_size - PERCPU_FIRST_CHUNK_RESERVE;
/* allocate pointer array and alloc large pages */
- ptrs_size = PFN_ALIGN(num_possible_cpus() * sizeof(pcpur_ptrs[0]));
- pcpur_ptrs = alloc_bootmem(ptrs_size);
+ map_size = PFN_ALIGN(num_possible_cpus() * sizeof(pcpul_map[0]));
+ pcpul_map = alloc_bootmem(map_size);
for_each_possible_cpu(cpu) {
- pcpur_ptrs[cpu] = pcpu_alloc_bootmem(cpu, PMD_SIZE, PMD_SIZE);
- if (!pcpur_ptrs[cpu])
+ pcpul_map[cpu].cpu = cpu;
+ pcpul_map[cpu].ptr = pcpu_alloc_bootmem(cpu, PMD_SIZE,
+ PMD_SIZE);
+ if (!pcpul_map[cpu].ptr) {
+ pr_warning("PERCPU: failed to allocate large page "
+ "for cpu%u\n", cpu);
goto enomem;
+ }
/*
- * Only use pcpur_size bytes and give back the rest.
+ * Only use pcpul_size bytes and give back the rest.
*
* Ingo: The 2MB up-rounding bootmem is needed to make
* sure the partial 2MB page is still fully RAM - it's
* not well-specified to have a PAT-incompatible area
* (unmapped RAM, device memory, etc.) in that hole.
*/
- free_bootmem(__pa(pcpur_ptrs[cpu] + pcpur_size),
- PMD_SIZE - pcpur_size);
+ free_bootmem(__pa(pcpul_map[cpu].ptr + pcpul_size),
+ PMD_SIZE - pcpul_size);
- memcpy(pcpur_ptrs[cpu], __per_cpu_load, static_size);
+ memcpy(pcpul_map[cpu].ptr, __per_cpu_load, static_size);
}
/* allocate address and map */
- vm.flags = VM_ALLOC;
- vm.size = num_possible_cpus() * PMD_SIZE;
- vm_area_register_early(&vm, PMD_SIZE);
+ pcpul_vm.flags = VM_ALLOC;
+ pcpul_vm.size = num_possible_cpus() * PMD_SIZE;
+ vm_area_register_early(&pcpul_vm, PMD_SIZE);
for_each_possible_cpu(cpu) {
- pmd_t *pmd;
+ pmd_t *pmd, pmd_v;
- pmd = populate_extra_pmd((unsigned long)vm.addr
- + cpu * PMD_SIZE);
- set_pmd(pmd, pfn_pmd(page_to_pfn(virt_to_page(pcpur_ptrs[cpu])),
- PAGE_KERNEL_LARGE));
+ pmd = populate_extra_pmd((unsigned long)pcpul_vm.addr +
+ cpu * PMD_SIZE);
+ pmd_v = pfn_pmd(page_to_pfn(virt_to_page(pcpul_map[cpu].ptr)),
+ PAGE_KERNEL_LARGE);
+ set_pmd(pmd, pmd_v);
}
/* we're ready, commit */
pr_info("PERCPU: Remapped at %p with large pages, static data "
- "%zu bytes\n", vm.addr, static_size);
+ "%zu bytes\n", pcpul_vm.addr, static_size);
- ret = pcpu_setup_first_chunk(pcpur_get_page, static_size,
+ ret = pcpu_setup_first_chunk(pcpul_get_page, static_size,
PERCPU_FIRST_CHUNK_RESERVE, dyn_size,
- PMD_SIZE, vm.addr, NULL);
- goto out_free_ar;
+ PMD_SIZE, pcpul_vm.addr, NULL);
+
+ /* sort pcpul_map array for pcpu_lpage_remapped() */
+ for (i = 0; i < num_possible_cpus() - 1; i++)
+ for (j = i + 1; j < num_possible_cpus(); j++)
+ if (pcpul_map[i].ptr > pcpul_map[j].ptr) {
+ struct pcpul_ent tmp = pcpul_map[i];
+ pcpul_map[i] = pcpul_map[j];
+ pcpul_map[j] = tmp;
+ }
+
+ return ret;
enomem:
for_each_possible_cpu(cpu)
- if (pcpur_ptrs[cpu])
- free_bootmem(__pa(pcpur_ptrs[cpu]), PMD_SIZE);
- ret = -ENOMEM;
-out_free_ar:
- free_bootmem(__pa(pcpur_ptrs), ptrs_size);
- return ret;
+ if (pcpul_map[cpu].ptr)
+ free_bootmem(__pa(pcpul_map[cpu].ptr), pcpul_size);
+ free_bootmem(__pa(pcpul_map), map_size);
+ return -ENOMEM;
+}
+
+/**
+ * pcpu_lpage_remapped - determine whether a kaddr is in pcpul recycled area
+ * @kaddr: the kernel address in question
+ *
+ * Determine whether @kaddr falls in the pcpul recycled area. This is
+ * used by pageattr to detect VM aliases and break up the pcpu PMD
+ * mapping such that the same physical page is not mapped under
+ * different attributes.
+ *
+ * The recycled area is always at the tail of a partially used PMD
+ * page.
+ *
+ * RETURNS:
+ * Address of corresponding remapped pcpu address if match is found;
+ * otherwise, NULL.
+ */
+void *pcpu_lpage_remapped(void *kaddr)
+{
+ void *pmd_addr = (void *)((unsigned long)kaddr & PMD_MASK);
+ unsigned long offset = (unsigned long)kaddr & ~PMD_MASK;
+ int left = 0, right = num_possible_cpus() - 1;
+ int pos;
+
+ /* pcpul in use at all? */
+ if (!pcpul_map)
+ return NULL;
+
+ /* okay, perform binary search */
+ while (left <= right) {
+ pos = (left + right) / 2;
+
+ if (pcpul_map[pos].ptr < pmd_addr)
+ left = pos + 1;
+ else if (pcpul_map[pos].ptr > pmd_addr)
+ right = pos - 1;
+ else {
+ /* it shouldn't be in the area for the first chunk */
+ WARN_ON(offset < pcpul_size);
+
+ return pcpul_vm.addr +
+ pcpul_map[pos].cpu * PMD_SIZE + offset;
+ }
+ }
+
+ return NULL;
}
#else
-static ssize_t __init setup_pcpu_remap(size_t static_size)
+static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen)
{
return -EINVAL;
}
* mapping so that it can use PMD mapping without additional TLB
* pressure.
*/
-static ssize_t __init setup_pcpu_embed(size_t static_size)
+static ssize_t __init setup_pcpu_embed(size_t static_size, bool chosen)
{
size_t reserve = PERCPU_MODULE_RESERVE + PERCPU_DYNAMIC_RESERVE;
* this. Also, embedding allocation doesn't play well with
* NUMA.
*/
- if (!cpu_has_pse || pcpu_need_numa())
+ if (!chosen && (!cpu_has_pse || pcpu_need_numa()))
return -EINVAL;
return pcpu_embed_first_chunk(static_size, PERCPU_FIRST_CHUNK_RESERVE,
void *ptr;
ptr = pcpu_alloc_bootmem(cpu, PAGE_SIZE, PAGE_SIZE);
- if (!ptr)
+ if (!ptr) {
+ pr_warning("PERCPU: failed to allocate "
+ "4k page for cpu%u\n", cpu);
goto enomem;
+ }
memcpy(ptr, __per_cpu_load + i * PAGE_SIZE, PAGE_SIZE);
pcpu4k_pages[j++] = virt_to_page(ptr);
return ret;
}
+/* for explicit first chunk allocator selection */
+static char pcpu_chosen_alloc[16] __initdata;
+
+static int __init percpu_alloc_setup(char *str)
+{
+ strncpy(pcpu_chosen_alloc, str, sizeof(pcpu_chosen_alloc) - 1);
+ return 0;
+}
+early_param("percpu_alloc", percpu_alloc_setup);
+
static inline void setup_percpu_segment(int cpu)
{
#ifdef CONFIG_X86_32
#endif
}
-/*
- * Great future plan:
- * Declare PDA itself and support (irqstack,tss,pgd) as per cpu data.
- * Always point %gs to its beginning
- */
void __init setup_per_cpu_areas(void)
{
size_t static_size = __per_cpu_end - __per_cpu_start;
* of large page mappings. Please read comments on top of
* each allocator for details.
*/
- ret = setup_pcpu_remap(static_size);
- if (ret < 0)
- ret = setup_pcpu_embed(static_size);
+ ret = -EINVAL;
+ if (strlen(pcpu_chosen_alloc)) {
+ if (strcmp(pcpu_chosen_alloc, "4k")) {
+ if (!strcmp(pcpu_chosen_alloc, "lpage"))
+ ret = setup_pcpu_lpage(static_size, true);
+ else if (!strcmp(pcpu_chosen_alloc, "embed"))
+ ret = setup_pcpu_embed(static_size, true);
+ else
+ pr_warning("PERCPU: unknown allocator %s "
+ "specified\n", pcpu_chosen_alloc);
+ if (ret < 0)
+ pr_warning("PERCPU: %s allocator failed (%zd), "
+ "falling back to 4k\n",
+ pcpu_chosen_alloc, ret);
+ }
+ } else {
+ ret = setup_pcpu_lpage(static_size, false);
+ if (ret < 0)
+ ret = setup_pcpu_embed(static_size, false);
+ }
if (ret < 0)
ret = setup_pcpu_4k(static_size);
if (ret < 0)
unsigned long pa;
unsigned long m;
unsigned long n;
- unsigned long mmr_image;
struct bau_desc *adp;
struct bau_desc *ad2;
n = pa >> uv_nshift;
m = pa & uv_mmask;
- mmr_image = uv_read_global_mmr64(pnode, UVH_LB_BAU_SB_DESCRIPTOR_BASE);
- if (mmr_image) {
- uv_write_global_mmr64(pnode, (unsigned long)
- UVH_LB_BAU_SB_DESCRIPTOR_BASE,
- (n << UV_DESC_BASE_PNODE_SHIFT | m));
- }
+ uv_write_global_mmr64(pnode, UVH_LB_BAU_SB_DESCRIPTOR_BASE,
+ (n << UV_DESC_BASE_PNODE_SHIFT | m));
/*
* initializing all 8 (UV_ITEMS_PER_DESCRIPTOR) descriptors for each
printk(KERN_EMERG "NMI: IOCK error (debug interrupt?)\n");
show_registers(regs);
+ if (panic_on_io_nmi)
+ panic("NMI IOCK error: Not continuing");
+
/* Re-enable the IOCK line, wait for a few seconds */
reason = (reason & 0xf) | 8;
outb(reason, 0x61);
else
/* 32 bits PSE 4MB page */
context->rsvd_bits_mask[1][1] = rsvd_bits(13, 21);
- context->rsvd_bits_mask[1][0] = ~0ull;
+ context->rsvd_bits_mask[1][0] = context->rsvd_bits_mask[1][0];
break;
case PT32E_ROOT_LEVEL:
context->rsvd_bits_mask[0][2] =
context->rsvd_bits_mask[1][1] = exb_bit_rsvd |
rsvd_bits(maxphyaddr, 62) |
rsvd_bits(13, 20); /* large page */
- context->rsvd_bits_mask[1][0] = ~0ull;
+ context->rsvd_bits_mask[1][0] = context->rsvd_bits_mask[1][0];
break;
case PT64_ROOT_LEVEL:
context->rsvd_bits_mask[0][3] = exb_bit_rsvd |
context->rsvd_bits_mask[1][1] = exb_bit_rsvd |
rsvd_bits(maxphyaddr, 51) |
rsvd_bits(13, 20); /* large page */
- context->rsvd_bits_mask[1][0] = ~0ull;
+ context->rsvd_bits_mask[1][0] = context->rsvd_bits_mask[1][0];
break;
}
}
{
unsigned access = gw->pt_access;
struct kvm_mmu_page *shadow_page;
- u64 spte, *sptep;
+ u64 spte, *sptep = NULL;
int direct;
gfn_t table_gfn;
int r;
return 1;
}
+static int handle_vmx_insn(struct kvm_vcpu *vcpu, struct kvm_run *kvm_run)
+{
+ kvm_queue_exception(vcpu, UD_VECTOR);
+ return 1;
+}
+
static int handle_invlpg(struct kvm_vcpu *vcpu, struct kvm_run *kvm_run)
{
unsigned long exit_qualification = vmcs_readl(EXIT_QUALIFICATION);
[EXIT_REASON_HLT] = handle_halt,
[EXIT_REASON_INVLPG] = handle_invlpg,
[EXIT_REASON_VMCALL] = handle_vmcall,
+ [EXIT_REASON_VMCLEAR] = handle_vmx_insn,
+ [EXIT_REASON_VMLAUNCH] = handle_vmx_insn,
+ [EXIT_REASON_VMPTRLD] = handle_vmx_insn,
+ [EXIT_REASON_VMPTRST] = handle_vmx_insn,
+ [EXIT_REASON_VMREAD] = handle_vmx_insn,
+ [EXIT_REASON_VMRESUME] = handle_vmx_insn,
+ [EXIT_REASON_VMWRITE] = handle_vmx_insn,
+ [EXIT_REASON_VMOFF] = handle_vmx_insn,
+ [EXIT_REASON_VMON] = handle_vmx_insn,
[EXIT_REASON_TPR_BELOW_THRESHOLD] = handle_tpr_below_threshold,
[EXIT_REASON_APIC_ACCESS] = handle_apic_access,
[EXIT_REASON_WBINVD] = handle_wbinvd,
case MSR_VM_HSAVE_PA:
case MSR_P6_EVNTSEL0:
case MSR_P6_EVNTSEL1:
+ case MSR_K7_EVNTSEL0:
data = 0;
break;
case MSR_MTRRcap:
return 0;
}
-void toggle_interruptibility(struct x86_emulate_ctxt *ctxt, u32 mask)
+static void toggle_interruptibility(struct x86_emulate_ctxt *ctxt, u32 mask)
{
u32 int_shadow = kvm_x86_ops->get_interrupt_shadow(ctxt->vcpu, mask);
/*
preempt_disable();
cpu = smp_processor_id();
+ rdtsc_barrier();
rdtscl(bclock);
for (;;) {
+ rdtsc_barrier();
rdtscl(now);
if ((now - bclock) >= loops)
break;
if (unlikely(cpu != smp_processor_id())) {
loops -= (now - bclock);
cpu = smp_processor_id();
+ rdtsc_barrier();
rdtscl(bclock);
}
}
return nr_range;
}
-#ifdef CONFIG_X86_64
-static void __init init_gbpages(void)
-{
- if (direct_gbpages && cpu_has_gbpages)
- printk(KERN_INFO "Using GB pages for direct mapping\n");
- else
- direct_gbpages = 0;
-}
-#else
-static inline void init_gbpages(void)
-{
-}
-#endif
-
/*
* Setup the direct mapping of the physical memory at PAGE_OFFSET.
* This runs before bootmem is initialized and gets pages directly from
printk(KERN_INFO "init_memory_mapping: %016lx-%016lx\n", start, end);
- if (!after_bootmem)
- init_gbpages();
-
#if defined(CONFIG_DEBUG_PAGEALLOC) || defined(CONFIG_KMEMCHECK)
/*
* For CONFIG_DEBUG_PAGEALLOC, identity mapping will use small pages.
#include <linux/interrupt.h>
#include <linux/seq_file.h>
#include <linux/debugfs.h>
+#include <linux/pfn.h>
#include <asm/e820.h>
#include <asm/processor.h>
static int cpa_process_alias(struct cpa_data *cpa)
{
struct cpa_data alias_cpa;
- int ret = 0;
- unsigned long temp_cpa_vaddr, vaddr;
+ unsigned long laddr = (unsigned long)__va(cpa->pfn << PAGE_SHIFT);
+ unsigned long vaddr, remapped;
+ int ret;
if (cpa->pfn >= max_pfn_mapped)
return 0;
PAGE_OFFSET + (max_pfn_mapped << PAGE_SHIFT)))) {
alias_cpa = *cpa;
- temp_cpa_vaddr = (unsigned long) __va(cpa->pfn << PAGE_SHIFT);
- alias_cpa.vaddr = &temp_cpa_vaddr;
+ alias_cpa.vaddr = &laddr;
alias_cpa.flags &= ~(CPA_PAGES_ARRAY | CPA_ARRAY);
-
ret = __change_page_attr_set_clr(&alias_cpa, 0);
+ if (ret)
+ return ret;
}
#ifdef CONFIG_X86_64
- if (ret)
- return ret;
/*
- * No need to redo, when the primary call touched the high
- * mapping already:
- */
- if (within(vaddr, (unsigned long) _text, _brk_end))
- return 0;
-
- /*
- * If the physical address is inside the kernel map, we need
+ * If the primary call didn't touch the high mapping already
+ * and the physical address is inside the kernel map, we need
* to touch the high mapped kernel as well:
*/
- if (!within(cpa->pfn, highmap_start_pfn(), highmap_end_pfn()))
- return 0;
+ if (!within(vaddr, (unsigned long)_text, _brk_end) &&
+ within(cpa->pfn, highmap_start_pfn(), highmap_end_pfn())) {
+ unsigned long temp_cpa_vaddr = (cpa->pfn << PAGE_SHIFT) +
+ __START_KERNEL_map - phys_base;
+ alias_cpa = *cpa;
+ alias_cpa.vaddr = &temp_cpa_vaddr;
+ alias_cpa.flags &= ~(CPA_PAGES_ARRAY | CPA_ARRAY);
- alias_cpa = *cpa;
- temp_cpa_vaddr = (cpa->pfn << PAGE_SHIFT) + __START_KERNEL_map - phys_base;
- alias_cpa.vaddr = &temp_cpa_vaddr;
- alias_cpa.flags &= ~(CPA_PAGES_ARRAY | CPA_ARRAY);
+ /*
+ * The high mapping range is imprecise, so ignore the
+ * return value.
+ */
+ __change_page_attr_set_clr(&alias_cpa, 0);
+ }
+#endif
/*
- * The high mapping range is imprecise, so ignore the return value.
+ * If the PMD page was partially used for per-cpu remapping,
+ * the recycled area needs to be split and modified. Because
+ * the area is always proper subset of a PMD page
+ * cpa->numpages is guaranteed to be 1 for these areas, so
+ * there's no need to loop over and check for further remaps.
*/
- __change_page_attr_set_clr(&alias_cpa, 0);
-#endif
- return ret;
+ remapped = (unsigned long)pcpu_lpage_remapped((void *)laddr);
+ if (remapped) {
+ WARN_ON(cpa->numpages > 1);
+ alias_cpa = *cpa;
+ alias_cpa.vaddr = &remapped;
+ alias_cpa.flags &= ~(CPA_PAGES_ARRAY | CPA_ARRAY);
+ ret = __change_page_attr_set_clr(&alias_cpa, 0);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
}
static int __change_page_attr_set_clr(struct cpa_data *cpa, int checkalias)
do_fpu_end();
mtrr_ap_init();
-#ifdef CONFIG_X86_32
+#ifdef CONFIG_X86_OLD_MCE
mcheck_init(&boot_cpu_data);
#endif
}
fn = adr & 0xffff;
pdev = pci_get_slot(pbus, PCI_DEVFN(dev, fn));
- if (hnd == handle)
+ if (!pdev || hnd == handle)
break;
pbus = pdev->subordinate;
#include <linux/cdev.h>
#include <linux/list.h>
#include <linux/mm.h>
+#include <asm/pgtable.h>
#include <asm/io.h>
/*
static int bsr_major;
enum {
- BSR_8 = 0,
- BSR_16 = 1,
- BSR_64 = 2,
- BSR_128 = 3,
- BSR_UNKNOWN = 4,
- BSR_MAX = 5,
+ BSR_8 = 0,
+ BSR_16 = 1,
+ BSR_64 = 2,
+ BSR_128 = 3,
+ BSR_4096 = 4,
+ BSR_UNKNOWN = 5,
+ BSR_MAX = 6,
};
static unsigned bsr_types[BSR_MAX];
{
unsigned long size = vma->vm_end - vma->vm_start;
struct bsr_dev *dev = filp->private_data;
+ int ret;
- if (size > dev->bsr_len || (size & (PAGE_SIZE-1)))
- return -EINVAL;
-
- vma->vm_flags |= (VM_IO | VM_DONTEXPAND);
vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
- if (io_remap_pfn_range(vma, vma->vm_start, dev->bsr_addr >> PAGE_SHIFT,
- size, vma->vm_page_prot))
+ /* check for the case of a small BSR device and map one 4k page for it*/
+ if (dev->bsr_len < PAGE_SIZE && size == PAGE_SIZE)
+ ret = remap_4k_pfn(vma, vma->vm_start, dev->bsr_addr >> 12,
+ vma->vm_page_prot);
+ else if (size <= dev->bsr_len)
+ ret = io_remap_pfn_range(vma, vma->vm_start,
+ dev->bsr_addr >> PAGE_SHIFT,
+ size, vma->vm_page_prot);
+ else
+ return -EINVAL;
+
+ if (ret)
return -EAGAIN;
return 0;
cur->bsr_stride = bsr_stride[i];
cur->bsr_dev = MKDEV(bsr_major, i + total_bsr_devs);
+ /* if we have a bsr_len of > 4k and less then PAGE_SIZE (64k pages) */
+ /* we can only map 4k of it, so only advertise the 4k in sysfs */
+ if (cur->bsr_len > 4096 && cur->bsr_len < PAGE_SIZE)
+ cur->bsr_len = 4096;
+
switch(cur->bsr_bytes) {
case 8:
cur->bsr_type = BSR_8;
case 128:
cur->bsr_type = BSR_128;
break;
+ case 4096:
+ cur->bsr_type = BSR_4096;
+ break;
default:
cur->bsr_type = BSR_UNKNOWN;
- printk(KERN_INFO "unknown BSR size %d\n",cur->bsr_bytes);
}
cur->bsr_num = bsr_types[cur->bsr_type];
tty_ldisc_wait_idle(tty);
/*
- * Shutdown the current line discipline, and reset it to N_TTY.
- *
- * FIXME: this MUST get fixed for the new reflocking
+ * Now kill off the ldisc
*/
+ tty_ldisc_close(tty, tty->ldisc);
+ tty_ldisc_put(tty->ldisc);
+ /* Force an oops if we mess this up */
+ tty->ldisc = NULL;
+
+ /* Ensure the next open requests the N_TTY ldisc */
+ tty_set_termios_ldisc(tty, N_TTY);
- tty_ldisc_reinit(tty);
/* This will need doing differently if we need to lock */
if (o_tty)
tty_ldisc_release(o_tty, NULL);
+
+ /* And the memory resources remaining (buffers, termios) will be
+ disposed of when the kref hits zero */
}
/**
static enum edac_type amd64_determine_edac_cap(struct amd64_pvt *pvt)
{
int bit;
- enum dev_type edac_cap = EDAC_NONE;
+ enum dev_type edac_cap = EDAC_FLAG_NONE;
bit = (boot_cpu_data.x86 > 0xf || pvt->ext_model >= OPTERON_CPU_REV_F)
? 19
: 17;
- if (pvt->dclr0 >> BIT(bit))
+ if (pvt->dclr0 & BIT(bit))
edac_cap = EDAC_FLAG_SECDED;
return edac_cap;
if (channels == 0)
channels = 1;
- debugf0("DIMM count= %d\n", channels);
+ debugf0("MCT channel count: %d\n", channels);
return channels;
" Use of the override can cause "
"unknown side effects.\n");
ret = -ENODEV;
- }
+ } else
+ /*
+ * enable further driver loading if ECC enable is
+ * overridden.
+ */
+ ret = 0;
} else {
amd64_printk(KERN_INFO,
"ECC is enabled by BIOS, Proceeding "
mci->mtype_cap = MEM_FLAG_DDR2 | MEM_FLAG_RDDR2;
mci->edac_ctl_cap = EDAC_FLAG_NONE;
- mci->edac_cap = EDAC_FLAG_NONE;
if (pvt->nbcap & K8_NBCAP_SECDED)
mci->edac_ctl_cap |= EDAC_FLAG_SECDED;
if (!pvt)
goto err_exit;
- pvt->mc_node_id = get_mc_node_id_from_pdev(dram_f2_ctl);
+ pvt->mc_node_id = get_node_id(dram_f2_ctl);
pvt->dram_f2_ctl = dram_f2_ctl;
pvt->ext_model = boot_cpu_data.x86_model >> 4;
{
int ret = 0;
- debugf0("(MC node=%d,mc_type='%s')\n",
- get_mc_node_id_from_pdev(pdev),
+ debugf0("(MC node=%d,mc_type='%s')\n", get_node_id(pdev),
get_amd_family_name(mc_type->driver_data));
ret = pci_enable_device(pdev);
err = amd64_init_2nd_stage(pvt_lookup[nb]);
if (err)
- goto err_exit;
+ goto err_2nd_stage;
}
amd64_setup_pci_device();
return 0;
+err_2nd_stage:
+ debugf0("2nd stage failed\n");
+
err_exit:
- debugf0("'finish_setup' stage failed\n");
pci_unregister_driver(&amd64_pci_driver);
return err;
#define K8_MSR_MC4ADDR 0x0412
/* AMD sets the first MC device at device ID 0x18. */
-static inline int get_mc_node_id_from_pdev(struct pci_dev *pdev)
+static inline int get_node_id(struct pci_dev *pdev)
{
return PCI_SLOT(pdev->devfn) - 0x18;
}
config DRM_I915
tristate "i915 driver"
+ depends on AGP_INTEL
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
drm-$(CONFIG_COMPAT) += drm_ioc32.o
obj-$(CONFIG_DRM) += drm.o
+obj-$(CONFIG_DRM_TTM) += ttm/
obj-$(CONFIG_DRM_TDFX) += tdfx/
obj-$(CONFIG_DRM_R128) += r128/
obj-$(CONFIG_DRM_RADEON)+= radeon/
obj-$(CONFIG_DRM_SIS) += sis/
obj-$(CONFIG_DRM_SAVAGE)+= savage/
obj-$(CONFIG_DRM_VIA) +=via/
-obj-$(CONFIG_DRM_TTM) += ttm/
unsigned vactive = (pt->vactive_vblank_hi & 0xf0) << 4 | pt->vactive_lo;
unsigned hblank = (pt->hactive_hblank_hi & 0xf) << 8 | pt->hblank_lo;
unsigned vblank = (pt->vactive_vblank_hi & 0xf) << 8 | pt->vblank_lo;
- unsigned hsync_offset = (pt->hsync_vsync_offset_pulse_width_hi & 0x3) << 8 | pt->hsync_offset_lo;
- unsigned hsync_pulse_width = (pt->hsync_vsync_offset_pulse_width_hi & 0xc) << 6 | pt->hsync_pulse_width_lo;
- unsigned vsync_offset = (pt->hsync_vsync_offset_pulse_width_hi & 0x30) | (pt->vsync_offset_pulse_width_lo & 0xf);
- unsigned vsync_pulse_width = (pt->hsync_vsync_offset_pulse_width_hi & 0xc0) >> 2 | pt->vsync_offset_pulse_width_lo >> 4;
+ unsigned hsync_offset = (pt->hsync_vsync_offset_pulse_width_hi & 0xc0) << 2 | pt->hsync_offset_lo;
+ unsigned hsync_pulse_width = (pt->hsync_vsync_offset_pulse_width_hi & 0x30) << 4 | pt->hsync_pulse_width_lo;
+ unsigned vsync_offset = (pt->hsync_vsync_offset_pulse_width_hi & 0xc) >> 2 | pt->vsync_offset_pulse_width_lo >> 4;
+ unsigned vsync_pulse_width = (pt->hsync_vsync_offset_pulse_width_hi & 0x3) << 4 | (pt->vsync_offset_pulse_width_lo & 0xf);
/* ignore tiny modes */
if (hactive < 64 || vactive < 64)
mode->flags |= (pt->misc & DRM_EDID_PT_VSYNC_POSITIVE) ?
DRM_MODE_FLAG_PVSYNC : DRM_MODE_FLAG_NVSYNC;
- mode->width_mm = pt->width_mm_lo | (pt->width_height_mm_hi & 0xf) << 8;
- mode->height_mm = pt->height_mm_lo | (pt->width_height_mm_hi & 0xf0) << 4;
+ mode->width_mm = pt->width_mm_lo | (pt->width_height_mm_hi & 0xf0) << 4;
+ mode->height_mm = pt->height_mm_lo | (pt->width_height_mm_hi & 0xf) << 8;
if (quirks & EDID_QUIRK_DETAILED_IN_CM) {
mode->width_mm *= 10;
intel_crt.o \
intel_lvds.o \
intel_bios.o \
+ intel_dp.o \
+ intel_dp_i2c.o \
intel_hdmi.o \
intel_sdvo.o \
intel_modes.o \
/* GPIO register used for i2c bus to control this device */
u32 gpio;
int slave_addr;
- struct intel_i2c_chan *i2c_bus;
+ struct i2c_adapter *i2c_bus;
const struct intel_dvo_dev_ops *dev_ops;
void *dev_priv;
* Returns NULL if the device does not exist.
*/
bool (*init)(struct intel_dvo_device *dvo,
- struct intel_i2c_chan *i2cbus);
+ struct i2c_adapter *i2cbus);
/*
* Called to allow the output a chance to create properties after the
static bool ch7017_read(struct intel_dvo_device *dvo, int addr, uint8_t *val)
{
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
u8 out_buf[2];
u8 in_buf[2];
struct i2c_msg msgs[] = {
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 1,
.buf = out_buf,
},
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = I2C_M_RD,
.len = 1,
.buf = in_buf,
static bool ch7017_write(struct intel_dvo_device *dvo, int addr, uint8_t val)
{
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
uint8_t out_buf[2];
struct i2c_msg msg = {
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 2,
.buf = out_buf,
/** Probes for a CH7017 on the given bus and slave address. */
static bool ch7017_init(struct intel_dvo_device *dvo,
- struct intel_i2c_chan *i2cbus)
+ struct i2c_adapter *adapter)
{
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
struct ch7017_priv *priv;
uint8_t val;
if (priv == NULL)
return false;
- dvo->i2c_bus = i2cbus;
- dvo->i2c_bus->slave_addr = dvo->slave_addr;
+ dvo->i2c_bus = adapter;
dvo->dev_priv = priv;
if (!ch7017_read(dvo, CH7017_DEVICE_ID, &val))
val != CH7018_DEVICE_ID_VALUE &&
val != CH7019_DEVICE_ID_VALUE) {
DRM_DEBUG("ch701x not detected, got %d: from %s Slave %d.\n",
- val, i2cbus->adapter.name,i2cbus->slave_addr);
+ val, i2cbus->adapter.name,dvo->slave_addr);
goto fail;
}
static bool ch7xxx_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
{
struct ch7xxx_priv *ch7xxx= dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
u8 out_buf[2];
u8 in_buf[2];
struct i2c_msg msgs[] = {
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 1,
.buf = out_buf,
},
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = I2C_M_RD,
.len = 1,
.buf = in_buf,
if (!ch7xxx->quiet) {
DRM_DEBUG("Unable to read register 0x%02x from %s:%02x.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
}
static bool ch7xxx_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
{
struct ch7xxx_priv *ch7xxx = dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
uint8_t out_buf[2];
struct i2c_msg msg = {
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 2,
.buf = out_buf,
if (!ch7xxx->quiet) {
DRM_DEBUG("Unable to write register 0x%02x to %s:%d.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
}
static bool ch7xxx_init(struct intel_dvo_device *dvo,
- struct intel_i2c_chan *i2cbus)
+ struct i2c_adapter *adapter)
{
/* this will detect the CH7xxx chip on the specified i2c bus */
struct ch7xxx_priv *ch7xxx;
if (ch7xxx == NULL)
return false;
- dvo->i2c_bus = i2cbus;
- dvo->i2c_bus->slave_addr = dvo->slave_addr;
+ dvo->i2c_bus = adapter;
dvo->dev_priv = ch7xxx;
ch7xxx->quiet = true;
name = ch7xxx_get_id(vendor);
if (!name) {
DRM_DEBUG("ch7xxx not detected; got 0x%02x from %s slave %d.\n",
- vendor, i2cbus->adapter.name, i2cbus->slave_addr);
+ vendor, adapter->name, dvo->slave_addr);
goto out;
}
if (device != CH7xxx_DID) {
DRM_DEBUG("ch7xxx not detected; got 0x%02x from %s slave %d.\n",
- vendor, i2cbus->adapter.name, i2cbus->slave_addr);
+ vendor, adapter->name, dvo->slave_addr);
goto out;
}
static bool ivch_read(struct intel_dvo_device *dvo, int addr, uint16_t *data)
{
struct ivch_priv *priv = dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
u8 out_buf[1];
u8 in_buf[2];
struct i2c_msg msgs[] = {
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = I2C_M_RD,
.len = 0,
},
.buf = out_buf,
},
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = I2C_M_RD | I2C_M_NOSTART,
.len = 2,
.buf = in_buf,
if (!priv->quiet) {
DRM_DEBUG("Unable to read register 0x%02x from %s:%02x.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
}
static bool ivch_write(struct intel_dvo_device *dvo, int addr, uint16_t data)
{
struct ivch_priv *priv = dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
u8 out_buf[3];
struct i2c_msg msg = {
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 3,
.buf = out_buf,
if (!priv->quiet) {
DRM_DEBUG("Unable to write register 0x%02x to %s:%d.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
/** Probes the given bus and slave address for an ivch */
static bool ivch_init(struct intel_dvo_device *dvo,
- struct intel_i2c_chan *i2cbus)
+ struct i2c_adapter *adapter)
{
struct ivch_priv *priv;
uint16_t temp;
if (priv == NULL)
return false;
- dvo->i2c_bus = i2cbus;
- dvo->i2c_bus->slave_addr = dvo->slave_addr;
+ dvo->i2c_bus = adapter;
dvo->dev_priv = priv;
priv->quiet = true;
static bool sil164_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
{
struct sil164_priv *sil = dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
u8 out_buf[2];
u8 in_buf[2];
struct i2c_msg msgs[] = {
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 1,
.buf = out_buf,
},
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = I2C_M_RD,
.len = 1,
.buf = in_buf,
if (!sil->quiet) {
DRM_DEBUG("Unable to read register 0x%02x from %s:%02x.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
}
static bool sil164_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
{
struct sil164_priv *sil= dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
uint8_t out_buf[2];
struct i2c_msg msg = {
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 2,
.buf = out_buf,
if (!sil->quiet) {
DRM_DEBUG("Unable to write register 0x%02x to %s:%d.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
/* Silicon Image 164 driver for chip on i2c bus */
static bool sil164_init(struct intel_dvo_device *dvo,
- struct intel_i2c_chan *i2cbus)
+ struct i2c_adapter *adapter)
{
/* this will detect the SIL164 chip on the specified i2c bus */
struct sil164_priv *sil;
if (sil == NULL)
return false;
- dvo->i2c_bus = i2cbus;
- dvo->i2c_bus->slave_addr = dvo->slave_addr;
+ dvo->i2c_bus = adapter;
dvo->dev_priv = sil;
sil->quiet = true;
if (ch != (SIL164_VID & 0xff)) {
DRM_DEBUG("sil164 not detected got %d: from %s Slave %d.\n",
- ch, i2cbus->adapter.name, i2cbus->slave_addr);
+ ch, adapter->name, dvo->slave_addr);
goto out;
}
if (ch != (SIL164_DID & 0xff)) {
DRM_DEBUG("sil164 not detected got %d: from %s Slave %d.\n",
- ch, i2cbus->adapter.name, i2cbus->slave_addr);
+ ch, adapter->name, dvo->slave_addr);
goto out;
}
sil->quiet = false;
static bool tfp410_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
{
struct tfp410_priv *tfp = dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
u8 out_buf[2];
u8 in_buf[2];
struct i2c_msg msgs[] = {
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 1,
.buf = out_buf,
},
{
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = I2C_M_RD,
.len = 1,
.buf = in_buf,
if (!tfp->quiet) {
DRM_DEBUG("Unable to read register 0x%02x from %s:%02x.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
}
static bool tfp410_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
{
struct tfp410_priv *tfp = dvo->dev_priv;
- struct intel_i2c_chan *i2cbus = dvo->i2c_bus;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_i2c_chan *i2cbus = container_of(adapter, struct intel_i2c_chan, adapter);
uint8_t out_buf[2];
struct i2c_msg msg = {
- .addr = i2cbus->slave_addr,
+ .addr = dvo->slave_addr,
.flags = 0,
.len = 2,
.buf = out_buf,
if (!tfp->quiet) {
DRM_DEBUG("Unable to write register 0x%02x to %s:%d.\n",
- addr, i2cbus->adapter.name, i2cbus->slave_addr);
+ addr, i2cbus->adapter.name, dvo->slave_addr);
}
return false;
/* Ti TFP410 driver for chip on i2c bus */
static bool tfp410_init(struct intel_dvo_device *dvo,
- struct intel_i2c_chan *i2cbus)
+ struct i2c_adapter *adapter)
{
/* this will detect the tfp410 chip on the specified i2c bus */
struct tfp410_priv *tfp;
if (tfp == NULL)
return false;
- dvo->i2c_bus = i2cbus;
- dvo->i2c_bus->slave_addr = dvo->slave_addr;
+ dvo->i2c_bus = adapter;
dvo->dev_priv = tfp;
tfp->quiet = true;
if ((id = tfp410_getid(dvo, TFP410_VID_LO)) != TFP410_VID) {
DRM_DEBUG("tfp410 not detected got VID %X: from %s Slave %d.\n",
- id, i2cbus->adapter.name, i2cbus->slave_addr);
+ id, adapter->name, dvo->slave_addr);
goto out;
}
if ((id = tfp410_getid(dvo, TFP410_DID_LO)) != TFP410_DID) {
DRM_DEBUG("tfp410 not detected got DID %X: from %s Slave %d.\n",
- id, i2cbus->adapter.name, i2cbus->slave_addr);
+ id, adapter->name, dvo->slave_addr);
goto out;
}
tfp->quiet = false;
pci_save_state(dev->pdev);
- i915_save_state(dev);
-
/* If KMS is active, we do the leavevt stuff here */
if (drm_core_check_feature(dev, DRIVER_MODESET)) {
if (i915_gem_idle(dev))
drm_irq_uninstall(dev);
}
+ i915_save_state(dev);
+
intel_opregion_free(dev, 1);
if (state.event == PM_EVENT_SUSPEND) {
u32 saveCURBPOS;
u32 saveCURBBASE;
u32 saveCURSIZE;
+ u32 saveDP_B;
+ u32 saveDP_C;
+ u32 saveDP_D;
+ u32 savePIPEA_GMCH_DATA_M;
+ u32 savePIPEB_GMCH_DATA_M;
+ u32 savePIPEA_GMCH_DATA_N;
+ u32 savePIPEB_GMCH_DATA_N;
+ u32 savePIPEA_DP_LINK_M;
+ u32 savePIPEB_DP_LINK_M;
+ u32 savePIPEA_DP_LINK_N;
+ u32 savePIPEB_DP_LINK_N;
struct {
struct drm_mm gtt_space;
#define HAS_128_BYTE_Y_TILING(dev) (IS_I9XX(dev) && !(IS_I915G(dev) || \
IS_I915GM(dev)))
#define SUPPORTS_INTEGRATED_HDMI(dev) (IS_G4X(dev) || IS_IGDNG(dev))
+#define SUPPORTS_INTEGRATED_DP(dev) (IS_G4X(dev) || IS_IGDNG(dev))
#define I915_HAS_HOTPLUG(dev) (IS_I945G(dev) || IS_I945GM(dev) || IS_I965G(dev))
#define PRIMARY_RINGBUFFER_SIZE (128*1024)
mutex_lock(&dev->struct_mutex);
#if WATCH_BUF
- DRM_INFO("set_domain_ioctl %p(%d), %08x %08x\n",
+ DRM_INFO("set_domain_ioctl %p(%zd), %08x %08x\n",
obj, obj->size, read_domains, write_domain);
#endif
if (read_domains & I915_GEM_DOMAIN_GTT) {
}
#if WATCH_BUF
- DRM_INFO("%s: sw_finish %d (%p %d)\n",
+ DRM_INFO("%s: sw_finish %d (%p %zd)\n",
__func__, args->handle, obj, obj->size);
#endif
obj_priv = obj->driver_private;
}
#if WATCH_BUF
- DRM_INFO("Binding object of size %d at 0x%08x\n",
+ DRM_INFO("Binding object of size %zd at 0x%08x\n",
obj->size, obj_priv->gtt_offset);
#endif
ret = i915_gem_object_get_pages(obj);
void
i915_gem_load(struct drm_device *dev)
{
+ int i;
drm_i915_private_t *dev_priv = dev->dev_private;
spin_lock_init(&dev_priv->mm.active_list_lock);
else
dev_priv->num_fence_regs = 8;
+ /* Initialize fence registers to zero */
+ if (IS_I965G(dev)) {
+ for (i = 0; i < 16; i++)
+ I915_WRITE64(FENCE_REG_965_0 + (i * 8), 0);
+ } else {
+ for (i = 0; i < 8; i++)
+ I915_WRITE(FENCE_REG_830_0 + (i * 4), 0);
+ if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
+ for (i = 0; i < 8; i++)
+ I915_WRITE(FENCE_REG_945_8 + (i * 4), 0);
+ }
+
i915_gem_detect_bit_6_swizzle(dev);
}
chunk_len = page_len - chunk;
if (chunk_len > 128)
chunk_len = 128;
- i915_gem_dump_page(obj_priv->page_list[page],
+ i915_gem_dump_page(obj_priv->pages[page],
chunk, chunk + chunk_len,
obj_priv->gtt_offset +
page * PAGE_SIZE,
uint32_t *backing_map = NULL;
int bad_count = 0;
- DRM_INFO("%s: checking coherency of object %p@0x%08x (%d, %dkb):\n",
+ DRM_INFO("%s: checking coherency of object %p@0x%08x (%d, %zdkb):\n",
__func__, obj, obj_priv->gtt_offset, handle,
obj->size / 1024);
for (page = 0; page < obj->size / PAGE_SIZE; page++) {
int i;
- backing_map = kmap_atomic(obj_priv->page_list[page], KM_USER0);
+ backing_map = kmap_atomic(obj_priv->pages[page], KM_USER0);
if (backing_map == NULL) {
DRM_ERROR("failed to map backing page\n");
mchbar_addr = ((u64)temp_hi << 32) | temp_lo;
/* If ACPI doesn't have it, assume we need to allocate it ourselves */
+#ifdef CONFIG_PNP
if (mchbar_addr &&
pnp_range_reserved(mchbar_addr, mchbar_addr + MCHBAR_SIZE)) {
ret = 0;
goto out_put;
}
+#endif
/* Get some space for it */
ret = pci_bus_alloc_resource(bridge_dev->bus, &dev_priv->mch_res,
drm_i915_private_t *dev_priv = container_of(work, drm_i915_private_t,
hotplug_work);
struct drm_device *dev = dev_priv->dev;
-
+ struct drm_mode_config *mode_config = &dev->mode_config;
+ struct drm_connector *connector;
+
+ if (mode_config->num_connector) {
+ list_for_each_entry(connector, &mode_config->connector_list, head) {
+ struct intel_output *intel_output = to_intel_output(connector);
+
+ if (intel_output->hot_plug)
+ (*intel_output->hot_plug) (intel_output);
+ }
+ }
/* Just fire off a uevent and let userspace tell us what to do */
drm_sysfs_hotplug_event(dev);
}
#define C0DRB3 0x10206
#define C1DRB3 0x10606
+/* Clocking configuration register */
+#define CLKCFG 0x10c00
+#define CLKCFG_FSB_400 (0 << 0) /* hrawclk 100 */
+#define CLKCFG_FSB_533 (1 << 0) /* hrawclk 133 */
+#define CLKCFG_FSB_667 (3 << 0) /* hrawclk 166 */
+#define CLKCFG_FSB_800 (2 << 0) /* hrawclk 200 */
+#define CLKCFG_FSB_1067 (6 << 0) /* hrawclk 266 */
+#define CLKCFG_FSB_1333 (7 << 0) /* hrawclk 333 */
+/* this is a guess, could be 5 as well */
+#define CLKCFG_FSB_1600 (4 << 0) /* hrawclk 400 */
+#define CLKCFG_FSB_1600_ALT (5 << 0) /* hrawclk 400 */
+#define CLKCFG_FSB_MASK (7 << 0)
+
/** GM965 GM45 render standby register */
#define MCHBAR_RENDER_STANDBY 0x111B8
#define HORIZ_INTERP_MASK (3 << 6)
#define HORIZ_AUTO_SCALE (1 << 5)
#define PANEL_8TO6_DITHER_ENABLE (1 << 3)
+#define PFIT_FILTER_FUZZY (0 << 24)
+#define PFIT_SCALING_AUTO (0 << 26)
+#define PFIT_SCALING_PROGRAMMED (1 << 26)
+#define PFIT_SCALING_PILLAR (2 << 26)
+#define PFIT_SCALING_LETTER (3 << 26)
#define PFIT_PGM_RATIOS 0x61234
#define PFIT_VERT_SCALE_MASK 0xfff00000
#define PFIT_HORIZ_SCALE_MASK 0x0000fff0
+/* Pre-965 */
+#define PFIT_VERT_SCALE_SHIFT 20
+#define PFIT_VERT_SCALE_MASK 0xfff00000
+#define PFIT_HORIZ_SCALE_SHIFT 4
+#define PFIT_HORIZ_SCALE_MASK 0x0000fff0
+/* 965+ */
+#define PFIT_VERT_SCALE_SHIFT_965 16
+#define PFIT_VERT_SCALE_MASK_965 0x1fff0000
+#define PFIT_HORIZ_SCALE_SHIFT_965 0
+#define PFIT_HORIZ_SCALE_MASK_965 0x00001fff
+
#define PFIT_AUTO_RATIOS 0x61238
/* Backlight control */
dev_priv->savePP_OFF_DELAYS = I915_READ(PP_OFF_DELAYS);
dev_priv->savePP_DIVISOR = I915_READ(PP_DIVISOR);
+ /* Display Port state */
+ if (SUPPORTS_INTEGRATED_DP(dev)) {
+ dev_priv->saveDP_B = I915_READ(DP_B);
+ dev_priv->saveDP_C = I915_READ(DP_C);
+ dev_priv->saveDP_D = I915_READ(DP_D);
+ dev_priv->savePIPEA_GMCH_DATA_M = I915_READ(PIPEA_GMCH_DATA_M);
+ dev_priv->savePIPEB_GMCH_DATA_M = I915_READ(PIPEB_GMCH_DATA_M);
+ dev_priv->savePIPEA_GMCH_DATA_N = I915_READ(PIPEA_GMCH_DATA_N);
+ dev_priv->savePIPEB_GMCH_DATA_N = I915_READ(PIPEB_GMCH_DATA_N);
+ dev_priv->savePIPEA_DP_LINK_M = I915_READ(PIPEA_DP_LINK_M);
+ dev_priv->savePIPEB_DP_LINK_M = I915_READ(PIPEB_DP_LINK_M);
+ dev_priv->savePIPEA_DP_LINK_N = I915_READ(PIPEA_DP_LINK_N);
+ dev_priv->savePIPEB_DP_LINK_N = I915_READ(PIPEB_DP_LINK_N);
+ }
/* FIXME: save TV & SDVO state */
/* FBC state */
for (i = 0; i < 8; i++)
I915_WRITE(FENCE_REG_945_8 + (i * 4), dev_priv->saveFENCE[i+8]);
}
-
+
+ /* Display port ratios (must be done before clock is set) */
+ if (SUPPORTS_INTEGRATED_DP(dev)) {
+ I915_WRITE(PIPEA_GMCH_DATA_M, dev_priv->savePIPEA_GMCH_DATA_M);
+ I915_WRITE(PIPEB_GMCH_DATA_M, dev_priv->savePIPEB_GMCH_DATA_M);
+ I915_WRITE(PIPEA_GMCH_DATA_N, dev_priv->savePIPEA_GMCH_DATA_N);
+ I915_WRITE(PIPEB_GMCH_DATA_N, dev_priv->savePIPEB_GMCH_DATA_N);
+ I915_WRITE(PIPEA_DP_LINK_M, dev_priv->savePIPEA_DP_LINK_M);
+ I915_WRITE(PIPEB_DP_LINK_M, dev_priv->savePIPEB_DP_LINK_M);
+ I915_WRITE(PIPEA_DP_LINK_N, dev_priv->savePIPEA_DP_LINK_N);
+ I915_WRITE(PIPEB_DP_LINK_N, dev_priv->savePIPEB_DP_LINK_N);
+ }
+
/* Pipe & plane A info */
/* Prime the clock */
if (dev_priv->saveDPLL_A & DPLL_VCO_ENABLE) {
I915_WRITE(PP_DIVISOR, dev_priv->savePP_DIVISOR);
I915_WRITE(PP_CONTROL, dev_priv->savePP_CONTROL);
+ /* Display Port state */
+ if (SUPPORTS_INTEGRATED_DP(dev)) {
+ I915_WRITE(DP_B, dev_priv->saveDP_B);
+ I915_WRITE(DP_C, dev_priv->saveDP_C);
+ I915_WRITE(DP_D, dev_priv->saveDP_D);
+ }
/* FIXME: restore TV & SDVO state */
/* FBC info */
{
struct bdb_lvds_options *lvds_options;
struct bdb_lvds_lfp_data *lvds_lfp_data;
+ struct bdb_lvds_lfp_data_ptrs *lvds_lfp_data_ptrs;
struct bdb_lvds_lfp_data_entry *entry;
struct lvds_dvo_timing *dvo_timing;
struct drm_display_mode *panel_fixed_mode;
+ int lfp_data_size;
/* Defaults if we can't find VBT info */
dev_priv->lvds_dither = 0;
if (!lvds_lfp_data)
return;
+ lvds_lfp_data_ptrs = find_section(bdb, BDB_LVDS_LFP_DATA_PTRS);
+ if (!lvds_lfp_data_ptrs)
+ return;
+
dev_priv->lvds_vbt = 1;
- entry = &lvds_lfp_data->data[lvds_options->panel_type];
+ lfp_data_size = lvds_lfp_data_ptrs->ptr[1].dvo_timing_offset -
+ lvds_lfp_data_ptrs->ptr[0].dvo_timing_offset;
+ entry = (struct bdb_lvds_lfp_data_entry *)
+ ((uint8_t *)lvds_lfp_data->data + (lfp_data_size *
+ lvds_options->panel_type));
dvo_timing = &entry->dvo_timing;
panel_fixed_mode = kzalloc(sizeof(*panel_fixed_mode), GFP_KERNEL);
#include "intel_drv.h"
#include "i915_drm.h"
#include "i915_drv.h"
+#include "intel_dp.h"
#include "drm_crtc_helper.h"
#define I9XX_P2_LVDS_FAST 7
#define I9XX_P2_LVDS_SLOW_LIMIT 112000
-#define INTEL_LIMIT_I8XX_DVO_DAC 0
-#define INTEL_LIMIT_I8XX_LVDS 1
-#define INTEL_LIMIT_I9XX_SDVO_DAC 2
-#define INTEL_LIMIT_I9XX_LVDS 3
-#define INTEL_LIMIT_G4X_SDVO 4
-#define INTEL_LIMIT_G4X_HDMI_DAC 5
-#define INTEL_LIMIT_G4X_SINGLE_CHANNEL_LVDS 6
-#define INTEL_LIMIT_G4X_DUAL_CHANNEL_LVDS 7
-#define INTEL_LIMIT_IGD_SDVO_DAC 8
-#define INTEL_LIMIT_IGD_LVDS 9
-#define INTEL_LIMIT_IGDNG_SDVO_DAC 10
-#define INTEL_LIMIT_IGDNG_LVDS 11
-
/*The parameter is for SDVO on G4x platform*/
#define G4X_DOT_SDVO_MIN 25000
#define G4X_DOT_SDVO_MAX 270000
#define G4X_P2_DUAL_CHANNEL_LVDS_FAST 7
#define G4X_P2_DUAL_CHANNEL_LVDS_LIMIT 0
+/*The parameter is for DISPLAY PORT on G4x platform*/
+#define G4X_DOT_DISPLAY_PORT_MIN 161670
+#define G4X_DOT_DISPLAY_PORT_MAX 227000
+#define G4X_N_DISPLAY_PORT_MIN 1
+#define G4X_N_DISPLAY_PORT_MAX 2
+#define G4X_M_DISPLAY_PORT_MIN 97
+#define G4X_M_DISPLAY_PORT_MAX 108
+#define G4X_M1_DISPLAY_PORT_MIN 0x10
+#define G4X_M1_DISPLAY_PORT_MAX 0x12
+#define G4X_M2_DISPLAY_PORT_MIN 0x05
+#define G4X_M2_DISPLAY_PORT_MAX 0x06
+#define G4X_P_DISPLAY_PORT_MIN 10
+#define G4X_P_DISPLAY_PORT_MAX 20
+#define G4X_P1_DISPLAY_PORT_MIN 1
+#define G4X_P1_DISPLAY_PORT_MAX 2
+#define G4X_P2_DISPLAY_PORT_SLOW 10
+#define G4X_P2_DISPLAY_PORT_FAST 10
+#define G4X_P2_DISPLAY_PORT_LIMIT 0
+
/* IGDNG */
/* as we calculate clock using (register_value + 2) for
N/M1/M2, so here the range value for them is (actual_value-2).
intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
int target, int refclk, intel_clock_t *best_clock);
-static const intel_limit_t intel_limits[] = {
- { /* INTEL_LIMIT_I8XX_DVO_DAC */
+static bool
+intel_find_pll_g4x_dp(const intel_limit_t *, struct drm_crtc *crtc,
+ int target, int refclk, intel_clock_t *best_clock);
+
+static const intel_limit_t intel_limits_i8xx_dvo = {
.dot = { .min = I8XX_DOT_MIN, .max = I8XX_DOT_MAX },
.vco = { .min = I8XX_VCO_MIN, .max = I8XX_VCO_MAX },
.n = { .min = I8XX_N_MIN, .max = I8XX_N_MAX },
.p2 = { .dot_limit = I8XX_P2_SLOW_LIMIT,
.p2_slow = I8XX_P2_SLOW, .p2_fast = I8XX_P2_FAST },
.find_pll = intel_find_best_PLL,
- },
- { /* INTEL_LIMIT_I8XX_LVDS */
+};
+
+static const intel_limit_t intel_limits_i8xx_lvds = {
.dot = { .min = I8XX_DOT_MIN, .max = I8XX_DOT_MAX },
.vco = { .min = I8XX_VCO_MIN, .max = I8XX_VCO_MAX },
.n = { .min = I8XX_N_MIN, .max = I8XX_N_MAX },
.p2 = { .dot_limit = I8XX_P2_SLOW_LIMIT,
.p2_slow = I8XX_P2_LVDS_SLOW, .p2_fast = I8XX_P2_LVDS_FAST },
.find_pll = intel_find_best_PLL,
- },
- { /* INTEL_LIMIT_I9XX_SDVO_DAC */
+};
+
+static const intel_limit_t intel_limits_i9xx_sdvo = {
.dot = { .min = I9XX_DOT_MIN, .max = I9XX_DOT_MAX },
.vco = { .min = I9XX_VCO_MIN, .max = I9XX_VCO_MAX },
.n = { .min = I9XX_N_MIN, .max = I9XX_N_MAX },
.p2 = { .dot_limit = I9XX_P2_SDVO_DAC_SLOW_LIMIT,
.p2_slow = I9XX_P2_SDVO_DAC_SLOW, .p2_fast = I9XX_P2_SDVO_DAC_FAST },
.find_pll = intel_find_best_PLL,
- },
- { /* INTEL_LIMIT_I9XX_LVDS */
+};
+
+static const intel_limit_t intel_limits_i9xx_lvds = {
.dot = { .min = I9XX_DOT_MIN, .max = I9XX_DOT_MAX },
.vco = { .min = I9XX_VCO_MIN, .max = I9XX_VCO_MAX },
.n = { .min = I9XX_N_MIN, .max = I9XX_N_MAX },
.p2 = { .dot_limit = I9XX_P2_LVDS_SLOW_LIMIT,
.p2_slow = I9XX_P2_LVDS_SLOW, .p2_fast = I9XX_P2_LVDS_FAST },
.find_pll = intel_find_best_PLL,
- },
+};
+
/* below parameter and function is for G4X Chipset Family*/
- { /* INTEL_LIMIT_G4X_SDVO */
+static const intel_limit_t intel_limits_g4x_sdvo = {
.dot = { .min = G4X_DOT_SDVO_MIN, .max = G4X_DOT_SDVO_MAX },
.vco = { .min = G4X_VCO_MIN, .max = G4X_VCO_MAX},
.n = { .min = G4X_N_SDVO_MIN, .max = G4X_N_SDVO_MAX },
.p2_fast = G4X_P2_SDVO_FAST
},
.find_pll = intel_g4x_find_best_PLL,
- },
- { /* INTEL_LIMIT_G4X_HDMI_DAC */
+};
+
+static const intel_limit_t intel_limits_g4x_hdmi = {
.dot = { .min = G4X_DOT_HDMI_DAC_MIN, .max = G4X_DOT_HDMI_DAC_MAX },
.vco = { .min = G4X_VCO_MIN, .max = G4X_VCO_MAX},
.n = { .min = G4X_N_HDMI_DAC_MIN, .max = G4X_N_HDMI_DAC_MAX },
.p2_fast = G4X_P2_HDMI_DAC_FAST
},
.find_pll = intel_g4x_find_best_PLL,
- },
- { /* INTEL_LIMIT_G4X_SINGLE_CHANNEL_LVDS */
+};
+
+static const intel_limit_t intel_limits_g4x_single_channel_lvds = {
.dot = { .min = G4X_DOT_SINGLE_CHANNEL_LVDS_MIN,
.max = G4X_DOT_SINGLE_CHANNEL_LVDS_MAX },
.vco = { .min = G4X_VCO_MIN,
.p2_fast = G4X_P2_SINGLE_CHANNEL_LVDS_FAST
},
.find_pll = intel_g4x_find_best_PLL,
- },
- { /* INTEL_LIMIT_G4X_DUAL_CHANNEL_LVDS */
+};
+
+static const intel_limit_t intel_limits_g4x_dual_channel_lvds = {
.dot = { .min = G4X_DOT_DUAL_CHANNEL_LVDS_MIN,
.max = G4X_DOT_DUAL_CHANNEL_LVDS_MAX },
.vco = { .min = G4X_VCO_MIN,
.p2_fast = G4X_P2_DUAL_CHANNEL_LVDS_FAST
},
.find_pll = intel_g4x_find_best_PLL,
- },
- { /* INTEL_LIMIT_IGD_SDVO */
+};
+
+static const intel_limit_t intel_limits_g4x_display_port = {
+ .dot = { .min = G4X_DOT_DISPLAY_PORT_MIN,
+ .max = G4X_DOT_DISPLAY_PORT_MAX },
+ .vco = { .min = G4X_VCO_MIN,
+ .max = G4X_VCO_MAX},
+ .n = { .min = G4X_N_DISPLAY_PORT_MIN,
+ .max = G4X_N_DISPLAY_PORT_MAX },
+ .m = { .min = G4X_M_DISPLAY_PORT_MIN,
+ .max = G4X_M_DISPLAY_PORT_MAX },
+ .m1 = { .min = G4X_M1_DISPLAY_PORT_MIN,
+ .max = G4X_M1_DISPLAY_PORT_MAX },
+ .m2 = { .min = G4X_M2_DISPLAY_PORT_MIN,
+ .max = G4X_M2_DISPLAY_PORT_MAX },
+ .p = { .min = G4X_P_DISPLAY_PORT_MIN,
+ .max = G4X_P_DISPLAY_PORT_MAX },
+ .p1 = { .min = G4X_P1_DISPLAY_PORT_MIN,
+ .max = G4X_P1_DISPLAY_PORT_MAX},
+ .p2 = { .dot_limit = G4X_P2_DISPLAY_PORT_LIMIT,
+ .p2_slow = G4X_P2_DISPLAY_PORT_SLOW,
+ .p2_fast = G4X_P2_DISPLAY_PORT_FAST },
+ .find_pll = intel_find_pll_g4x_dp,
+};
+
+static const intel_limit_t intel_limits_igd_sdvo = {
.dot = { .min = I9XX_DOT_MIN, .max = I9XX_DOT_MAX},
.vco = { .min = IGD_VCO_MIN, .max = IGD_VCO_MAX },
.n = { .min = IGD_N_MIN, .max = IGD_N_MAX },
.p2 = { .dot_limit = I9XX_P2_SDVO_DAC_SLOW_LIMIT,
.p2_slow = I9XX_P2_SDVO_DAC_SLOW, .p2_fast = I9XX_P2_SDVO_DAC_FAST },
.find_pll = intel_find_best_PLL,
- },
- { /* INTEL_LIMIT_IGD_LVDS */
+};
+
+static const intel_limit_t intel_limits_igd_lvds = {
.dot = { .min = I9XX_DOT_MIN, .max = I9XX_DOT_MAX },
.vco = { .min = IGD_VCO_MIN, .max = IGD_VCO_MAX },
.n = { .min = IGD_N_MIN, .max = IGD_N_MAX },
.p2 = { .dot_limit = I9XX_P2_LVDS_SLOW_LIMIT,
.p2_slow = I9XX_P2_LVDS_SLOW, .p2_fast = I9XX_P2_LVDS_SLOW },
.find_pll = intel_find_best_PLL,
- },
- { /* INTEL_LIMIT_IGDNG_SDVO_DAC */
+};
+
+static const intel_limit_t intel_limits_igdng_sdvo = {
.dot = { .min = IGDNG_DOT_MIN, .max = IGDNG_DOT_MAX },
.vco = { .min = IGDNG_VCO_MIN, .max = IGDNG_VCO_MAX },
.n = { .min = IGDNG_N_MIN, .max = IGDNG_N_MAX },
.p2_slow = IGDNG_P2_SDVO_DAC_SLOW,
.p2_fast = IGDNG_P2_SDVO_DAC_FAST },
.find_pll = intel_igdng_find_best_PLL,
- },
- { /* INTEL_LIMIT_IGDNG_LVDS */
+};
+
+static const intel_limit_t intel_limits_igdng_lvds = {
.dot = { .min = IGDNG_DOT_MIN, .max = IGDNG_DOT_MAX },
.vco = { .min = IGDNG_VCO_MIN, .max = IGDNG_VCO_MAX },
.n = { .min = IGDNG_N_MIN, .max = IGDNG_N_MAX },
.p2_slow = IGDNG_P2_LVDS_SLOW,
.p2_fast = IGDNG_P2_LVDS_FAST },
.find_pll = intel_igdng_find_best_PLL,
- },
};
static const intel_limit_t *intel_igdng_limit(struct drm_crtc *crtc)
{
const intel_limit_t *limit;
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
- limit = &intel_limits[INTEL_LIMIT_IGDNG_LVDS];
+ limit = &intel_limits_igdng_lvds;
else
- limit = &intel_limits[INTEL_LIMIT_IGDNG_SDVO_DAC];
+ limit = &intel_limits_igdng_sdvo;
return limit;
}
if ((I915_READ(LVDS) & LVDS_CLKB_POWER_MASK) ==
LVDS_CLKB_POWER_UP)
/* LVDS with dual channel */
- limit = &intel_limits
- [INTEL_LIMIT_G4X_DUAL_CHANNEL_LVDS];
+ limit = &intel_limits_g4x_dual_channel_lvds;
else
/* LVDS with dual channel */
- limit = &intel_limits
- [INTEL_LIMIT_G4X_SINGLE_CHANNEL_LVDS];
+ limit = &intel_limits_g4x_single_channel_lvds;
} else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_HDMI) ||
intel_pipe_has_type(crtc, INTEL_OUTPUT_ANALOG)) {
- limit = &intel_limits[INTEL_LIMIT_G4X_HDMI_DAC];
+ limit = &intel_limits_g4x_hdmi;
} else if (intel_pipe_has_type(crtc, INTEL_OUTPUT_SDVO)) {
- limit = &intel_limits[INTEL_LIMIT_G4X_SDVO];
+ limit = &intel_limits_g4x_sdvo;
+ } else if (intel_pipe_has_type (crtc, INTEL_OUTPUT_DISPLAYPORT)) {
+ limit = &intel_limits_g4x_display_port;
} else /* The option is for other outputs */
- limit = &intel_limits[INTEL_LIMIT_I9XX_SDVO_DAC];
+ limit = &intel_limits_i9xx_sdvo;
return limit;
}
limit = intel_g4x_limit(crtc);
} else if (IS_I9XX(dev) && !IS_IGD(dev)) {
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
- limit = &intel_limits[INTEL_LIMIT_I9XX_LVDS];
+ limit = &intel_limits_i9xx_lvds;
else
- limit = &intel_limits[INTEL_LIMIT_I9XX_SDVO_DAC];
+ limit = &intel_limits_i9xx_sdvo;
} else if (IS_IGD(dev)) {
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
- limit = &intel_limits[INTEL_LIMIT_IGD_LVDS];
+ limit = &intel_limits_igd_lvds;
else
- limit = &intel_limits[INTEL_LIMIT_IGD_SDVO_DAC];
+ limit = &intel_limits_igd_sdvo;
} else {
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
- limit = &intel_limits[INTEL_LIMIT_I8XX_LVDS];
+ limit = &intel_limits_i8xx_lvds;
else
- limit = &intel_limits[INTEL_LIMIT_I8XX_DVO_DAC];
+ limit = &intel_limits_i8xx_dvo;
}
return limit;
}
return found;
}
+/* DisplayPort has only two frequencies, 162MHz and 270MHz */
+static bool
+intel_find_pll_g4x_dp(const intel_limit_t *limit, struct drm_crtc *crtc,
+ int target, int refclk, intel_clock_t *best_clock)
+{
+ intel_clock_t clock;
+ if (target < 200000) {
+ clock.dot = 161670;
+ clock.p = 20;
+ clock.p1 = 2;
+ clock.p2 = 10;
+ clock.n = 0x01;
+ clock.m = 97;
+ clock.m1 = 0x10;
+ clock.m2 = 0x05;
+ } else {
+ clock.dot = 270000;
+ clock.p = 10;
+ clock.p1 = 1;
+ clock.p2 = 10;
+ clock.n = 0x02;
+ clock.m = 108;
+ clock.m1 = 0x12;
+ clock.m2 = 0x06;
+ }
+ memcpy(best_clock, &clock, sizeof(intel_clock_t));
+ return true;
+}
+
void
intel_wait_for_vblank(struct drm_device *dev)
{
intel_clock_t clock;
u32 dpll = 0, fp = 0, dspcntr, pipeconf;
bool ok, is_sdvo = false, is_dvo = false;
- bool is_crt = false, is_lvds = false, is_tv = false;
+ bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
struct drm_mode_config *mode_config = &dev->mode_config;
struct drm_connector *connector;
const intel_limit_t *limit;
case INTEL_OUTPUT_ANALOG:
is_crt = true;
break;
+ case INTEL_OUTPUT_DISPLAYPORT:
+ is_dp = true;
+ break;
}
num_outputs++;
} else {
refclk = 48000;
}
+
/*
* Returns a set of divisors for the desired target clock with the given
else if (IS_IGDNG(dev))
dpll |= (sdvo_pixel_multiply - 1) << PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT;
}
+ if (is_dp)
+ dpll |= DPLL_DVO_HIGH_SPEED;
/* compute bitmask from p1 value */
if (IS_IGD(dev))
I915_WRITE(lvds_reg, lvds);
I915_READ(lvds_reg);
}
+ if (is_dp)
+ intel_dp_set_m_n(crtc, mode, adjusted_mode);
I915_WRITE(fp_reg, fp);
I915_WRITE(dpll_reg, dpll);
found = intel_sdvo_init(dev, SDVOB);
if (!found && SUPPORTS_INTEGRATED_HDMI(dev))
intel_hdmi_init(dev, SDVOB);
+ if (!found && SUPPORTS_INTEGRATED_DP(dev))
+ intel_dp_init(dev, DP_B);
}
/* Before G4X SDVOC doesn't have its own detect register */
found = intel_sdvo_init(dev, SDVOC);
if (!found && SUPPORTS_INTEGRATED_HDMI(dev))
intel_hdmi_init(dev, SDVOC);
+ if (!found && SUPPORTS_INTEGRATED_DP(dev))
+ intel_dp_init(dev, DP_C);
}
+ if (SUPPORTS_INTEGRATED_DP(dev) && (I915_READ(DP_D) & DP_DETECTED))
+ intel_dp_init(dev, DP_D);
} else
intel_dvo_init(dev);
(1 << 1));
clone_mask = (1 << INTEL_OUTPUT_TVOUT);
break;
+ case INTEL_OUTPUT_DISPLAYPORT:
+ crtc_mask = ((1 << 0) |
+ (1 << 1));
+ clone_mask = (1 << INTEL_OUTPUT_DISPLAYPORT);
+ break;
}
encoder->possible_crtcs = crtc_mask;
encoder->possible_clones = intel_connector_clones(dev, clone_mask);
--- /dev/null
+/*
+ * Copyright © 2008 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
+ * IN THE SOFTWARE.
+ *
+ * Authors:
+ * Keith Packard <keithp@keithp.com>
+ *
+ */
+
+#include <linux/i2c.h>
+#include "drmP.h"
+#include "drm.h"
+#include "drm_crtc.h"
+#include "drm_crtc_helper.h"
+#include "intel_drv.h"
+#include "i915_drm.h"
+#include "i915_drv.h"
+#include "intel_dp.h"
+
+#define DP_LINK_STATUS_SIZE 6
+#define DP_LINK_CHECK_TIMEOUT (10 * 1000)
+
+#define DP_LINK_CONFIGURATION_SIZE 9
+
+struct intel_dp_priv {
+ uint32_t output_reg;
+ uint32_t DP;
+ uint8_t link_configuration[DP_LINK_CONFIGURATION_SIZE];
+ uint32_t save_DP;
+ uint8_t save_link_configuration[DP_LINK_CONFIGURATION_SIZE];
+ bool has_audio;
+ int dpms_mode;
+ uint8_t link_bw;
+ uint8_t lane_count;
+ uint8_t dpcd[4];
+ struct intel_output *intel_output;
+ struct i2c_adapter adapter;
+ struct i2c_algo_dp_aux_data algo;
+};
+
+static void
+intel_dp_link_train(struct intel_output *intel_output, uint32_t DP,
+ uint8_t link_configuration[DP_LINK_CONFIGURATION_SIZE]);
+
+static void
+intel_dp_link_down(struct intel_output *intel_output, uint32_t DP);
+
+static int
+intel_dp_max_lane_count(struct intel_output *intel_output)
+{
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ int max_lane_count = 4;
+
+ if (dp_priv->dpcd[0] >= 0x11) {
+ max_lane_count = dp_priv->dpcd[2] & 0x1f;
+ switch (max_lane_count) {
+ case 1: case 2: case 4:
+ break;
+ default:
+ max_lane_count = 4;
+ }
+ }
+ return max_lane_count;
+}
+
+static int
+intel_dp_max_link_bw(struct intel_output *intel_output)
+{
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ int max_link_bw = dp_priv->dpcd[1];
+
+ switch (max_link_bw) {
+ case DP_LINK_BW_1_62:
+ case DP_LINK_BW_2_7:
+ break;
+ default:
+ max_link_bw = DP_LINK_BW_1_62;
+ break;
+ }
+ return max_link_bw;
+}
+
+static int
+intel_dp_link_clock(uint8_t link_bw)
+{
+ if (link_bw == DP_LINK_BW_2_7)
+ return 270000;
+ else
+ return 162000;
+}
+
+/* I think this is a fiction */
+static int
+intel_dp_link_required(int pixel_clock)
+{
+ return pixel_clock * 3;
+}
+
+static int
+intel_dp_mode_valid(struct drm_connector *connector,
+ struct drm_display_mode *mode)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+ int max_link_clock = intel_dp_link_clock(intel_dp_max_link_bw(intel_output));
+ int max_lanes = intel_dp_max_lane_count(intel_output);
+
+ if (intel_dp_link_required(mode->clock) > max_link_clock * max_lanes)
+ return MODE_CLOCK_HIGH;
+
+ if (mode->clock < 10000)
+ return MODE_CLOCK_LOW;
+
+ return MODE_OK;
+}
+
+static uint32_t
+pack_aux(uint8_t *src, int src_bytes)
+{
+ int i;
+ uint32_t v = 0;
+
+ if (src_bytes > 4)
+ src_bytes = 4;
+ for (i = 0; i < src_bytes; i++)
+ v |= ((uint32_t) src[i]) << ((3-i) * 8);
+ return v;
+}
+
+static void
+unpack_aux(uint32_t src, uint8_t *dst, int dst_bytes)
+{
+ int i;
+ if (dst_bytes > 4)
+ dst_bytes = 4;
+ for (i = 0; i < dst_bytes; i++)
+ dst[i] = src >> ((3-i) * 8);
+}
+
+/* hrawclock is 1/4 the FSB frequency */
+static int
+intel_hrawclk(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ uint32_t clkcfg;
+
+ clkcfg = I915_READ(CLKCFG);
+ switch (clkcfg & CLKCFG_FSB_MASK) {
+ case CLKCFG_FSB_400:
+ return 100;
+ case CLKCFG_FSB_533:
+ return 133;
+ case CLKCFG_FSB_667:
+ return 166;
+ case CLKCFG_FSB_800:
+ return 200;
+ case CLKCFG_FSB_1067:
+ return 266;
+ case CLKCFG_FSB_1333:
+ return 333;
+ /* these two are just a guess; one of them might be right */
+ case CLKCFG_FSB_1600:
+ case CLKCFG_FSB_1600_ALT:
+ return 400;
+ default:
+ return 133;
+ }
+}
+
+static int
+intel_dp_aux_ch(struct intel_output *intel_output,
+ uint8_t *send, int send_bytes,
+ uint8_t *recv, int recv_size)
+{
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ uint32_t output_reg = dp_priv->output_reg;
+ struct drm_device *dev = intel_output->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ uint32_t ch_ctl = output_reg + 0x10;
+ uint32_t ch_data = ch_ctl + 4;
+ int i;
+ int recv_bytes;
+ uint32_t ctl;
+ uint32_t status;
+ uint32_t aux_clock_divider;
+ int try;
+
+ /* The clock divider is based off the hrawclk,
+ * and would like to run at 2MHz. So, take the
+ * hrawclk value and divide by 2 and use that
+ */
+ aux_clock_divider = intel_hrawclk(dev) / 2;
+ /* Must try at least 3 times according to DP spec */
+ for (try = 0; try < 5; try++) {
+ /* Load the send data into the aux channel data registers */
+ for (i = 0; i < send_bytes; i += 4) {
+ uint32_t d = pack_aux(send + i, send_bytes - i);;
+
+ I915_WRITE(ch_data + i, d);
+ }
+
+ ctl = (DP_AUX_CH_CTL_SEND_BUSY |
+ DP_AUX_CH_CTL_TIME_OUT_400us |
+ (send_bytes << DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT) |
+ (5 << DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT) |
+ (aux_clock_divider << DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT) |
+ DP_AUX_CH_CTL_DONE |
+ DP_AUX_CH_CTL_TIME_OUT_ERROR |
+ DP_AUX_CH_CTL_RECEIVE_ERROR);
+
+ /* Send the command and wait for it to complete */
+ I915_WRITE(ch_ctl, ctl);
+ (void) I915_READ(ch_ctl);
+ for (;;) {
+ udelay(100);
+ status = I915_READ(ch_ctl);
+ if ((status & DP_AUX_CH_CTL_SEND_BUSY) == 0)
+ break;
+ }
+
+ /* Clear done status and any errors */
+ I915_WRITE(ch_ctl, (ctl |
+ DP_AUX_CH_CTL_DONE |
+ DP_AUX_CH_CTL_TIME_OUT_ERROR |
+ DP_AUX_CH_CTL_RECEIVE_ERROR));
+ (void) I915_READ(ch_ctl);
+ if ((status & DP_AUX_CH_CTL_TIME_OUT_ERROR) == 0)
+ break;
+ }
+
+ if ((status & DP_AUX_CH_CTL_DONE) == 0) {
+ printk(KERN_ERR "dp_aux_ch not done status 0x%08x\n", status);
+ return -EBUSY;
+ }
+
+ /* Check for timeout or receive error.
+ * Timeouts occur when the sink is not connected
+ */
+ if (status & DP_AUX_CH_CTL_RECEIVE_ERROR) {
+ printk(KERN_ERR "dp_aux_ch receive error status 0x%08x\n", status);
+ return -EIO;
+ }
+ if (status & DP_AUX_CH_CTL_TIME_OUT_ERROR) {
+ printk(KERN_ERR "dp_aux_ch timeout status 0x%08x\n", status);
+ return -ETIMEDOUT;
+ }
+
+ /* Unload any bytes sent back from the other side */
+ recv_bytes = ((status & DP_AUX_CH_CTL_MESSAGE_SIZE_MASK) >>
+ DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT);
+
+ if (recv_bytes > recv_size)
+ recv_bytes = recv_size;
+
+ for (i = 0; i < recv_bytes; i += 4) {
+ uint32_t d = I915_READ(ch_data + i);
+
+ unpack_aux(d, recv + i, recv_bytes - i);
+ }
+
+ return recv_bytes;
+}
+
+/* Write data to the aux channel in native mode */
+static int
+intel_dp_aux_native_write(struct intel_output *intel_output,
+ uint16_t address, uint8_t *send, int send_bytes)
+{
+ int ret;
+ uint8_t msg[20];
+ int msg_bytes;
+ uint8_t ack;
+
+ if (send_bytes > 16)
+ return -1;
+ msg[0] = AUX_NATIVE_WRITE << 4;
+ msg[1] = address >> 8;
+ msg[2] = address;
+ msg[3] = send_bytes - 1;
+ memcpy(&msg[4], send, send_bytes);
+ msg_bytes = send_bytes + 4;
+ for (;;) {
+ ret = intel_dp_aux_ch(intel_output, msg, msg_bytes, &ack, 1);
+ if (ret < 0)
+ return ret;
+ if ((ack & AUX_NATIVE_REPLY_MASK) == AUX_NATIVE_REPLY_ACK)
+ break;
+ else if ((ack & AUX_NATIVE_REPLY_MASK) == AUX_NATIVE_REPLY_DEFER)
+ udelay(100);
+ else
+ return -EIO;
+ }
+ return send_bytes;
+}
+
+/* Write a single byte to the aux channel in native mode */
+static int
+intel_dp_aux_native_write_1(struct intel_output *intel_output,
+ uint16_t address, uint8_t byte)
+{
+ return intel_dp_aux_native_write(intel_output, address, &byte, 1);
+}
+
+/* read bytes from a native aux channel */
+static int
+intel_dp_aux_native_read(struct intel_output *intel_output,
+ uint16_t address, uint8_t *recv, int recv_bytes)
+{
+ uint8_t msg[4];
+ int msg_bytes;
+ uint8_t reply[20];
+ int reply_bytes;
+ uint8_t ack;
+ int ret;
+
+ msg[0] = AUX_NATIVE_READ << 4;
+ msg[1] = address >> 8;
+ msg[2] = address & 0xff;
+ msg[3] = recv_bytes - 1;
+
+ msg_bytes = 4;
+ reply_bytes = recv_bytes + 1;
+
+ for (;;) {
+ ret = intel_dp_aux_ch(intel_output, msg, msg_bytes,
+ reply, reply_bytes);
+ if (ret == 0)
+ return -EPROTO;
+ if (ret < 0)
+ return ret;
+ ack = reply[0];
+ if ((ack & AUX_NATIVE_REPLY_MASK) == AUX_NATIVE_REPLY_ACK) {
+ memcpy(recv, reply + 1, ret - 1);
+ return ret - 1;
+ }
+ else if ((ack & AUX_NATIVE_REPLY_MASK) == AUX_NATIVE_REPLY_DEFER)
+ udelay(100);
+ else
+ return -EIO;
+ }
+}
+
+static int
+intel_dp_i2c_aux_ch(struct i2c_adapter *adapter,
+ uint8_t *send, int send_bytes,
+ uint8_t *recv, int recv_bytes)
+{
+ struct intel_dp_priv *dp_priv = container_of(adapter,
+ struct intel_dp_priv,
+ adapter);
+ struct intel_output *intel_output = dp_priv->intel_output;
+
+ return intel_dp_aux_ch(intel_output,
+ send, send_bytes, recv, recv_bytes);
+}
+
+static int
+intel_dp_i2c_init(struct intel_output *intel_output, const char *name)
+{
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+
+ DRM_ERROR("i2c_init %s\n", name);
+ dp_priv->algo.running = false;
+ dp_priv->algo.address = 0;
+ dp_priv->algo.aux_ch = intel_dp_i2c_aux_ch;
+
+ memset(&dp_priv->adapter, '\0', sizeof (dp_priv->adapter));
+ dp_priv->adapter.owner = THIS_MODULE;
+ dp_priv->adapter.class = I2C_CLASS_DDC;
+ strncpy (dp_priv->adapter.name, name, sizeof dp_priv->adapter.name - 1);
+ dp_priv->adapter.name[sizeof dp_priv->adapter.name - 1] = '\0';
+ dp_priv->adapter.algo_data = &dp_priv->algo;
+ dp_priv->adapter.dev.parent = &intel_output->base.kdev;
+
+ return i2c_dp_aux_add_bus(&dp_priv->adapter);
+}
+
+static bool
+intel_dp_mode_fixup(struct drm_encoder *encoder, struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct intel_output *intel_output = enc_to_intel_output(encoder);
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ int lane_count, clock;
+ int max_lane_count = intel_dp_max_lane_count(intel_output);
+ int max_clock = intel_dp_max_link_bw(intel_output) == DP_LINK_BW_2_7 ? 1 : 0;
+ static int bws[2] = { DP_LINK_BW_1_62, DP_LINK_BW_2_7 };
+
+ for (lane_count = 1; lane_count <= max_lane_count; lane_count <<= 1) {
+ for (clock = 0; clock <= max_clock; clock++) {
+ int link_avail = intel_dp_link_clock(bws[clock]) * lane_count;
+
+ if (intel_dp_link_required(mode->clock) <= link_avail) {
+ dp_priv->link_bw = bws[clock];
+ dp_priv->lane_count = lane_count;
+ adjusted_mode->clock = intel_dp_link_clock(dp_priv->link_bw);
+ printk(KERN_ERR "link bw %02x lane count %d clock %d\n",
+ dp_priv->link_bw, dp_priv->lane_count,
+ adjusted_mode->clock);
+ return true;
+ }
+ }
+ }
+ return false;
+}
+
+struct intel_dp_m_n {
+ uint32_t tu;
+ uint32_t gmch_m;
+ uint32_t gmch_n;
+ uint32_t link_m;
+ uint32_t link_n;
+};
+
+static void
+intel_reduce_ratio(uint32_t *num, uint32_t *den)
+{
+ while (*num > 0xffffff || *den > 0xffffff) {
+ *num >>= 1;
+ *den >>= 1;
+ }
+}
+
+static void
+intel_dp_compute_m_n(int bytes_per_pixel,
+ int nlanes,
+ int pixel_clock,
+ int link_clock,
+ struct intel_dp_m_n *m_n)
+{
+ m_n->tu = 64;
+ m_n->gmch_m = pixel_clock * bytes_per_pixel;
+ m_n->gmch_n = link_clock * nlanes;
+ intel_reduce_ratio(&m_n->gmch_m, &m_n->gmch_n);
+ m_n->link_m = pixel_clock;
+ m_n->link_n = link_clock;
+ intel_reduce_ratio(&m_n->link_m, &m_n->link_n);
+}
+
+void
+intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_mode_config *mode_config = &dev->mode_config;
+ struct drm_connector *connector;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int lane_count = 4;
+ struct intel_dp_m_n m_n;
+
+ /*
+ * Find the lane count in the intel_output private
+ */
+ list_for_each_entry(connector, &mode_config->connector_list, head) {
+ struct intel_output *intel_output = to_intel_output(connector);
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+
+ if (!connector->encoder || connector->encoder->crtc != crtc)
+ continue;
+
+ if (intel_output->type == INTEL_OUTPUT_DISPLAYPORT) {
+ lane_count = dp_priv->lane_count;
+ break;
+ }
+ }
+
+ /*
+ * Compute the GMCH and Link ratios. The '3' here is
+ * the number of bytes_per_pixel post-LUT, which we always
+ * set up for 8-bits of R/G/B, or 3 bytes total.
+ */
+ intel_dp_compute_m_n(3, lane_count,
+ mode->clock, adjusted_mode->clock, &m_n);
+
+ if (intel_crtc->pipe == 0) {
+ I915_WRITE(PIPEA_GMCH_DATA_M,
+ ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
+ m_n.gmch_m);
+ I915_WRITE(PIPEA_GMCH_DATA_N,
+ m_n.gmch_n);
+ I915_WRITE(PIPEA_DP_LINK_M, m_n.link_m);
+ I915_WRITE(PIPEA_DP_LINK_N, m_n.link_n);
+ } else {
+ I915_WRITE(PIPEB_GMCH_DATA_M,
+ ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
+ m_n.gmch_m);
+ I915_WRITE(PIPEB_GMCH_DATA_N,
+ m_n.gmch_n);
+ I915_WRITE(PIPEB_DP_LINK_M, m_n.link_m);
+ I915_WRITE(PIPEB_DP_LINK_N, m_n.link_n);
+ }
+}
+
+static void
+intel_dp_mode_set(struct drm_encoder *encoder, struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct intel_output *intel_output = enc_to_intel_output(encoder);
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ struct drm_crtc *crtc = intel_output->enc.crtc;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+
+ dp_priv->DP = (DP_LINK_TRAIN_OFF |
+ DP_VOLTAGE_0_4 |
+ DP_PRE_EMPHASIS_0 |
+ DP_SYNC_VS_HIGH |
+ DP_SYNC_HS_HIGH);
+
+ switch (dp_priv->lane_count) {
+ case 1:
+ dp_priv->DP |= DP_PORT_WIDTH_1;
+ break;
+ case 2:
+ dp_priv->DP |= DP_PORT_WIDTH_2;
+ break;
+ case 4:
+ dp_priv->DP |= DP_PORT_WIDTH_4;
+ break;
+ }
+ if (dp_priv->has_audio)
+ dp_priv->DP |= DP_AUDIO_OUTPUT_ENABLE;
+
+ memset(dp_priv->link_configuration, 0, DP_LINK_CONFIGURATION_SIZE);
+ dp_priv->link_configuration[0] = dp_priv->link_bw;
+ dp_priv->link_configuration[1] = dp_priv->lane_count;
+
+ /*
+ * Check for DPCD version > 1.1,
+ * enable enahanced frame stuff in that case
+ */
+ if (dp_priv->dpcd[0] >= 0x11) {
+ dp_priv->link_configuration[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
+ dp_priv->DP |= DP_ENHANCED_FRAMING;
+ }
+
+ if (intel_crtc->pipe == 1)
+ dp_priv->DP |= DP_PIPEB_SELECT;
+}
+
+
+static void
+intel_dp_dpms(struct drm_encoder *encoder, int mode)
+{
+ struct intel_output *intel_output = enc_to_intel_output(encoder);
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ struct drm_device *dev = intel_output->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ uint32_t dp_reg = I915_READ(dp_priv->output_reg);
+
+ if (mode != DRM_MODE_DPMS_ON) {
+ if (dp_reg & DP_PORT_EN)
+ intel_dp_link_down(intel_output, dp_priv->DP);
+ } else {
+ if (!(dp_reg & DP_PORT_EN))
+ intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration);
+ }
+ dp_priv->dpms_mode = mode;
+}
+
+/*
+ * Fetch AUX CH registers 0x202 - 0x207 which contain
+ * link status information
+ */
+static bool
+intel_dp_get_link_status(struct intel_output *intel_output,
+ uint8_t link_status[DP_LINK_STATUS_SIZE])
+{
+ int ret;
+
+ ret = intel_dp_aux_native_read(intel_output,
+ DP_LANE0_1_STATUS,
+ link_status, DP_LINK_STATUS_SIZE);
+ if (ret != DP_LINK_STATUS_SIZE)
+ return false;
+ return true;
+}
+
+static uint8_t
+intel_dp_link_status(uint8_t link_status[DP_LINK_STATUS_SIZE],
+ int r)
+{
+ return link_status[r - DP_LANE0_1_STATUS];
+}
+
+static void
+intel_dp_save(struct drm_connector *connector)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+ struct drm_device *dev = intel_output->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+
+ dp_priv->save_DP = I915_READ(dp_priv->output_reg);
+ intel_dp_aux_native_read(intel_output, DP_LINK_BW_SET,
+ dp_priv->save_link_configuration,
+ sizeof (dp_priv->save_link_configuration));
+}
+
+static uint8_t
+intel_get_adjust_request_voltage(uint8_t link_status[DP_LINK_STATUS_SIZE],
+ int lane)
+{
+ int i = DP_ADJUST_REQUEST_LANE0_1 + (lane >> 1);
+ int s = ((lane & 1) ?
+ DP_ADJUST_VOLTAGE_SWING_LANE1_SHIFT :
+ DP_ADJUST_VOLTAGE_SWING_LANE0_SHIFT);
+ uint8_t l = intel_dp_link_status(link_status, i);
+
+ return ((l >> s) & 3) << DP_TRAIN_VOLTAGE_SWING_SHIFT;
+}
+
+static uint8_t
+intel_get_adjust_request_pre_emphasis(uint8_t link_status[DP_LINK_STATUS_SIZE],
+ int lane)
+{
+ int i = DP_ADJUST_REQUEST_LANE0_1 + (lane >> 1);
+ int s = ((lane & 1) ?
+ DP_ADJUST_PRE_EMPHASIS_LANE1_SHIFT :
+ DP_ADJUST_PRE_EMPHASIS_LANE0_SHIFT);
+ uint8_t l = intel_dp_link_status(link_status, i);
+
+ return ((l >> s) & 3) << DP_TRAIN_PRE_EMPHASIS_SHIFT;
+}
+
+
+#if 0
+static char *voltage_names[] = {
+ "0.4V", "0.6V", "0.8V", "1.2V"
+};
+static char *pre_emph_names[] = {
+ "0dB", "3.5dB", "6dB", "9.5dB"
+};
+static char *link_train_names[] = {
+ "pattern 1", "pattern 2", "idle", "off"
+};
+#endif
+
+/*
+ * These are source-specific values; current Intel hardware supports
+ * a maximum voltage of 800mV and a maximum pre-emphasis of 6dB
+ */
+#define I830_DP_VOLTAGE_MAX DP_TRAIN_VOLTAGE_SWING_800
+
+static uint8_t
+intel_dp_pre_emphasis_max(uint8_t voltage_swing)
+{
+ switch (voltage_swing & DP_TRAIN_VOLTAGE_SWING_MASK) {
+ case DP_TRAIN_VOLTAGE_SWING_400:
+ return DP_TRAIN_PRE_EMPHASIS_6;
+ case DP_TRAIN_VOLTAGE_SWING_600:
+ return DP_TRAIN_PRE_EMPHASIS_6;
+ case DP_TRAIN_VOLTAGE_SWING_800:
+ return DP_TRAIN_PRE_EMPHASIS_3_5;
+ case DP_TRAIN_VOLTAGE_SWING_1200:
+ default:
+ return DP_TRAIN_PRE_EMPHASIS_0;
+ }
+}
+
+static void
+intel_get_adjust_train(struct intel_output *intel_output,
+ uint8_t link_status[DP_LINK_STATUS_SIZE],
+ int lane_count,
+ uint8_t train_set[4])
+{
+ uint8_t v = 0;
+ uint8_t p = 0;
+ int lane;
+
+ for (lane = 0; lane < lane_count; lane++) {
+ uint8_t this_v = intel_get_adjust_request_voltage(link_status, lane);
+ uint8_t this_p = intel_get_adjust_request_pre_emphasis(link_status, lane);
+
+ if (this_v > v)
+ v = this_v;
+ if (this_p > p)
+ p = this_p;
+ }
+
+ if (v >= I830_DP_VOLTAGE_MAX)
+ v = I830_DP_VOLTAGE_MAX | DP_TRAIN_MAX_SWING_REACHED;
+
+ if (p >= intel_dp_pre_emphasis_max(v))
+ p = intel_dp_pre_emphasis_max(v) | DP_TRAIN_MAX_PRE_EMPHASIS_REACHED;
+
+ for (lane = 0; lane < 4; lane++)
+ train_set[lane] = v | p;
+}
+
+static uint32_t
+intel_dp_signal_levels(uint8_t train_set, int lane_count)
+{
+ uint32_t signal_levels = 0;
+
+ switch (train_set & DP_TRAIN_VOLTAGE_SWING_MASK) {
+ case DP_TRAIN_VOLTAGE_SWING_400:
+ default:
+ signal_levels |= DP_VOLTAGE_0_4;
+ break;
+ case DP_TRAIN_VOLTAGE_SWING_600:
+ signal_levels |= DP_VOLTAGE_0_6;
+ break;
+ case DP_TRAIN_VOLTAGE_SWING_800:
+ signal_levels |= DP_VOLTAGE_0_8;
+ break;
+ case DP_TRAIN_VOLTAGE_SWING_1200:
+ signal_levels |= DP_VOLTAGE_1_2;
+ break;
+ }
+ switch (train_set & DP_TRAIN_PRE_EMPHASIS_MASK) {
+ case DP_TRAIN_PRE_EMPHASIS_0:
+ default:
+ signal_levels |= DP_PRE_EMPHASIS_0;
+ break;
+ case DP_TRAIN_PRE_EMPHASIS_3_5:
+ signal_levels |= DP_PRE_EMPHASIS_3_5;
+ break;
+ case DP_TRAIN_PRE_EMPHASIS_6:
+ signal_levels |= DP_PRE_EMPHASIS_6;
+ break;
+ case DP_TRAIN_PRE_EMPHASIS_9_5:
+ signal_levels |= DP_PRE_EMPHASIS_9_5;
+ break;
+ }
+ return signal_levels;
+}
+
+static uint8_t
+intel_get_lane_status(uint8_t link_status[DP_LINK_STATUS_SIZE],
+ int lane)
+{
+ int i = DP_LANE0_1_STATUS + (lane >> 1);
+ int s = (lane & 1) * 4;
+ uint8_t l = intel_dp_link_status(link_status, i);
+
+ return (l >> s) & 0xf;
+}
+
+/* Check for clock recovery is done on all channels */
+static bool
+intel_clock_recovery_ok(uint8_t link_status[DP_LINK_STATUS_SIZE], int lane_count)
+{
+ int lane;
+ uint8_t lane_status;
+
+ for (lane = 0; lane < lane_count; lane++) {
+ lane_status = intel_get_lane_status(link_status, lane);
+ if ((lane_status & DP_LANE_CR_DONE) == 0)
+ return false;
+ }
+ return true;
+}
+
+/* Check to see if channel eq is done on all channels */
+#define CHANNEL_EQ_BITS (DP_LANE_CR_DONE|\
+ DP_LANE_CHANNEL_EQ_DONE|\
+ DP_LANE_SYMBOL_LOCKED)
+static bool
+intel_channel_eq_ok(uint8_t link_status[DP_LINK_STATUS_SIZE], int lane_count)
+{
+ uint8_t lane_align;
+ uint8_t lane_status;
+ int lane;
+
+ lane_align = intel_dp_link_status(link_status,
+ DP_LANE_ALIGN_STATUS_UPDATED);
+ if ((lane_align & DP_INTERLANE_ALIGN_DONE) == 0)
+ return false;
+ for (lane = 0; lane < lane_count; lane++) {
+ lane_status = intel_get_lane_status(link_status, lane);
+ if ((lane_status & CHANNEL_EQ_BITS) != CHANNEL_EQ_BITS)
+ return false;
+ }
+ return true;
+}
+
+static bool
+intel_dp_set_link_train(struct intel_output *intel_output,
+ uint32_t dp_reg_value,
+ uint8_t dp_train_pat,
+ uint8_t train_set[4],
+ bool first)
+{
+ struct drm_device *dev = intel_output->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ int ret;
+
+ I915_WRITE(dp_priv->output_reg, dp_reg_value);
+ POSTING_READ(dp_priv->output_reg);
+ if (first)
+ intel_wait_for_vblank(dev);
+
+ intel_dp_aux_native_write_1(intel_output,
+ DP_TRAINING_PATTERN_SET,
+ dp_train_pat);
+
+ ret = intel_dp_aux_native_write(intel_output,
+ DP_TRAINING_LANE0_SET, train_set, 4);
+ if (ret != 4)
+ return false;
+
+ return true;
+}
+
+static void
+intel_dp_link_train(struct intel_output *intel_output, uint32_t DP,
+ uint8_t link_configuration[DP_LINK_CONFIGURATION_SIZE])
+{
+ struct drm_device *dev = intel_output->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ uint8_t train_set[4];
+ uint8_t link_status[DP_LINK_STATUS_SIZE];
+ int i;
+ uint8_t voltage;
+ bool clock_recovery = false;
+ bool channel_eq = false;
+ bool first = true;
+ int tries;
+
+ /* Write the link configuration data */
+ intel_dp_aux_native_write(intel_output, 0x100,
+ link_configuration, DP_LINK_CONFIGURATION_SIZE);
+
+ DP |= DP_PORT_EN;
+ DP &= ~DP_LINK_TRAIN_MASK;
+ memset(train_set, 0, 4);
+ voltage = 0xff;
+ tries = 0;
+ clock_recovery = false;
+ for (;;) {
+ /* Use train_set[0] to set the voltage and pre emphasis values */
+ uint32_t signal_levels = intel_dp_signal_levels(train_set[0], dp_priv->lane_count);
+ DP = (DP & ~(DP_VOLTAGE_MASK|DP_PRE_EMPHASIS_MASK)) | signal_levels;
+
+ if (!intel_dp_set_link_train(intel_output, DP | DP_LINK_TRAIN_PAT_1,
+ DP_TRAINING_PATTERN_1, train_set, first))
+ break;
+ first = false;
+ /* Set training pattern 1 */
+
+ udelay(100);
+ if (!intel_dp_get_link_status(intel_output, link_status))
+ break;
+
+ if (intel_clock_recovery_ok(link_status, dp_priv->lane_count)) {
+ clock_recovery = true;
+ break;
+ }
+
+ /* Check to see if we've tried the max voltage */
+ for (i = 0; i < dp_priv->lane_count; i++)
+ if ((train_set[i] & DP_TRAIN_MAX_SWING_REACHED) == 0)
+ break;
+ if (i == dp_priv->lane_count)
+ break;
+
+ /* Check to see if we've tried the same voltage 5 times */
+ if ((train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) == voltage) {
+ ++tries;
+ if (tries == 5)
+ break;
+ } else
+ tries = 0;
+ voltage = train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK;
+
+ /* Compute new train_set as requested by target */
+ intel_get_adjust_train(intel_output, link_status, dp_priv->lane_count, train_set);
+ }
+
+ /* channel equalization */
+ tries = 0;
+ channel_eq = false;
+ for (;;) {
+ /* Use train_set[0] to set the voltage and pre emphasis values */
+ uint32_t signal_levels = intel_dp_signal_levels(train_set[0], dp_priv->lane_count);
+ DP = (DP & ~(DP_VOLTAGE_MASK|DP_PRE_EMPHASIS_MASK)) | signal_levels;
+
+ /* channel eq pattern */
+ if (!intel_dp_set_link_train(intel_output, DP | DP_LINK_TRAIN_PAT_2,
+ DP_TRAINING_PATTERN_2, train_set,
+ false))
+ break;
+
+ udelay(400);
+ if (!intel_dp_get_link_status(intel_output, link_status))
+ break;
+
+ if (intel_channel_eq_ok(link_status, dp_priv->lane_count)) {
+ channel_eq = true;
+ break;
+ }
+
+ /* Try 5 times */
+ if (tries > 5)
+ break;
+
+ /* Compute new train_set as requested by target */
+ intel_get_adjust_train(intel_output, link_status, dp_priv->lane_count, train_set);
+ ++tries;
+ }
+
+ I915_WRITE(dp_priv->output_reg, DP | DP_LINK_TRAIN_OFF);
+ POSTING_READ(dp_priv->output_reg);
+ intel_dp_aux_native_write_1(intel_output,
+ DP_TRAINING_PATTERN_SET, DP_TRAINING_PATTERN_DISABLE);
+}
+
+static void
+intel_dp_link_down(struct intel_output *intel_output, uint32_t DP)
+{
+ struct drm_device *dev = intel_output->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+
+ I915_WRITE(dp_priv->output_reg, DP & ~DP_PORT_EN);
+ POSTING_READ(dp_priv->output_reg);
+}
+
+static void
+intel_dp_restore(struct drm_connector *connector)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+
+ if (dp_priv->save_DP & DP_PORT_EN)
+ intel_dp_link_train(intel_output, dp_priv->save_DP, dp_priv->save_link_configuration);
+ else
+ intel_dp_link_down(intel_output, dp_priv->save_DP);
+}
+
+/*
+ * According to DP spec
+ * 5.1.2:
+ * 1. Read DPCD
+ * 2. Configure link according to Receiver Capabilities
+ * 3. Use Link Training from 2.5.3.3 and 3.5.1.3
+ * 4. Check link status on receipt of hot-plug interrupt
+ */
+
+static void
+intel_dp_check_link_status(struct intel_output *intel_output)
+{
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ uint8_t link_status[DP_LINK_STATUS_SIZE];
+
+ if (!intel_output->enc.crtc)
+ return;
+
+ if (!intel_dp_get_link_status(intel_output, link_status)) {
+ intel_dp_link_down(intel_output, dp_priv->DP);
+ return;
+ }
+
+ if (!intel_channel_eq_ok(link_status, dp_priv->lane_count))
+ intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration);
+}
+
+/**
+ * Uses CRT_HOTPLUG_EN and CRT_HOTPLUG_STAT to detect DP connection.
+ *
+ * \return true if DP port is connected.
+ * \return false if DP port is disconnected.
+ */
+static enum drm_connector_status
+intel_dp_detect(struct drm_connector *connector)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+ struct drm_device *dev = intel_output->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+ uint32_t temp, bit;
+ enum drm_connector_status status;
+
+ dp_priv->has_audio = false;
+
+ temp = I915_READ(PORT_HOTPLUG_EN);
+
+ I915_WRITE(PORT_HOTPLUG_EN,
+ temp |
+ DPB_HOTPLUG_INT_EN |
+ DPC_HOTPLUG_INT_EN |
+ DPD_HOTPLUG_INT_EN);
+
+ POSTING_READ(PORT_HOTPLUG_EN);
+
+ switch (dp_priv->output_reg) {
+ case DP_B:
+ bit = DPB_HOTPLUG_INT_STATUS;
+ break;
+ case DP_C:
+ bit = DPC_HOTPLUG_INT_STATUS;
+ break;
+ case DP_D:
+ bit = DPD_HOTPLUG_INT_STATUS;
+ break;
+ default:
+ return connector_status_unknown;
+ }
+
+ temp = I915_READ(PORT_HOTPLUG_STAT);
+
+ if ((temp & bit) == 0)
+ return connector_status_disconnected;
+
+ status = connector_status_disconnected;
+ if (intel_dp_aux_native_read(intel_output,
+ 0x000, dp_priv->dpcd,
+ sizeof (dp_priv->dpcd)) == sizeof (dp_priv->dpcd))
+ {
+ if (dp_priv->dpcd[0] != 0)
+ status = connector_status_connected;
+ }
+ return status;
+}
+
+static int intel_dp_get_modes(struct drm_connector *connector)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+
+ /* We should parse the EDID data and find out if it has an audio sink
+ */
+
+ return intel_ddc_get_modes(intel_output);
+}
+
+static void
+intel_dp_destroy (struct drm_connector *connector)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+
+ if (intel_output->i2c_bus)
+ intel_i2c_destroy(intel_output->i2c_bus);
+ drm_sysfs_connector_remove(connector);
+ drm_connector_cleanup(connector);
+ kfree(intel_output);
+}
+
+static const struct drm_encoder_helper_funcs intel_dp_helper_funcs = {
+ .dpms = intel_dp_dpms,
+ .mode_fixup = intel_dp_mode_fixup,
+ .prepare = intel_encoder_prepare,
+ .mode_set = intel_dp_mode_set,
+ .commit = intel_encoder_commit,
+};
+
+static const struct drm_connector_funcs intel_dp_connector_funcs = {
+ .dpms = drm_helper_connector_dpms,
+ .save = intel_dp_save,
+ .restore = intel_dp_restore,
+ .detect = intel_dp_detect,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .destroy = intel_dp_destroy,
+};
+
+static const struct drm_connector_helper_funcs intel_dp_connector_helper_funcs = {
+ .get_modes = intel_dp_get_modes,
+ .mode_valid = intel_dp_mode_valid,
+ .best_encoder = intel_best_encoder,
+};
+
+static void intel_dp_enc_destroy(struct drm_encoder *encoder)
+{
+ drm_encoder_cleanup(encoder);
+}
+
+static const struct drm_encoder_funcs intel_dp_enc_funcs = {
+ .destroy = intel_dp_enc_destroy,
+};
+
+void
+intel_dp_hot_plug(struct intel_output *intel_output)
+{
+ struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+
+ if (dp_priv->dpms_mode == DRM_MODE_DPMS_ON)
+ intel_dp_check_link_status(intel_output);
+}
+
+void
+intel_dp_init(struct drm_device *dev, int output_reg)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_connector *connector;
+ struct intel_output *intel_output;
+ struct intel_dp_priv *dp_priv;
+
+ intel_output = kcalloc(sizeof(struct intel_output) +
+ sizeof(struct intel_dp_priv), 1, GFP_KERNEL);
+ if (!intel_output)
+ return;
+
+ dp_priv = (struct intel_dp_priv *)(intel_output + 1);
+
+ connector = &intel_output->base;
+ drm_connector_init(dev, connector, &intel_dp_connector_funcs,
+ DRM_MODE_CONNECTOR_DisplayPort);
+ drm_connector_helper_add(connector, &intel_dp_connector_helper_funcs);
+
+ intel_output->type = INTEL_OUTPUT_DISPLAYPORT;
+
+ connector->interlace_allowed = true;
+ connector->doublescan_allowed = 0;
+
+ dp_priv->intel_output = intel_output;
+ dp_priv->output_reg = output_reg;
+ dp_priv->has_audio = false;
+ dp_priv->dpms_mode = DRM_MODE_DPMS_ON;
+ intel_output->dev_priv = dp_priv;
+
+ drm_encoder_init(dev, &intel_output->enc, &intel_dp_enc_funcs,
+ DRM_MODE_ENCODER_TMDS);
+ drm_encoder_helper_add(&intel_output->enc, &intel_dp_helper_funcs);
+
+ drm_mode_connector_attach_encoder(&intel_output->base,
+ &intel_output->enc);
+ drm_sysfs_connector_add(connector);
+
+ /* Set up the DDC bus. */
+ intel_dp_i2c_init(intel_output,
+ (output_reg == DP_B) ? "DPDDC-B" :
+ (output_reg == DP_C) ? "DPDDC-C" : "DPDDC-D");
+ intel_output->ddc_bus = &dp_priv->adapter;
+ intel_output->hot_plug = intel_dp_hot_plug;
+
+ /* For G4X desktop chip, PEG_BAND_GAP_DATA 3:0 must first be written
+ * 0xd. Failure to do so will result in spurious interrupts being
+ * generated on the port when a cable is not attached.
+ */
+ if (IS_G4X(dev) && !IS_GM45(dev)) {
+ u32 temp = I915_READ(PEG_BAND_GAP_DATA);
+ I915_WRITE(PEG_BAND_GAP_DATA, (temp & ~0xf) | 0xd);
+ }
+}
--- /dev/null
+/*
+ * Copyright © 2008 Keith Packard
+ *
+ * Permission to use, copy, modify, distribute, and sell this software and its
+ * documentation for any purpose is hereby granted without fee, provided that
+ * the above copyright notice appear in all copies and that both that copyright
+ * notice and this permission notice appear in supporting documentation, and
+ * that the name of the copyright holders not be used in advertising or
+ * publicity pertaining to distribution of the software without specific,
+ * written prior permission. The copyright holders make no representations
+ * about the suitability of this software for any purpose. It is provided "as
+ * is" without express or implied warranty.
+ *
+ * THE COPYRIGHT HOLDERS DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE,
+ * INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO
+ * EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
+ * CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE,
+ * DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
+ * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
+ * OF THIS SOFTWARE.
+ */
+
+#ifndef _INTEL_DP_H_
+#define _INTEL_DP_H_
+
+/* From the VESA DisplayPort spec */
+
+#define AUX_NATIVE_WRITE 0x8
+#define AUX_NATIVE_READ 0x9
+#define AUX_I2C_WRITE 0x0
+#define AUX_I2C_READ 0x1
+#define AUX_I2C_STATUS 0x2
+#define AUX_I2C_MOT 0x4
+
+#define AUX_NATIVE_REPLY_ACK (0x0 << 4)
+#define AUX_NATIVE_REPLY_NACK (0x1 << 4)
+#define AUX_NATIVE_REPLY_DEFER (0x2 << 4)
+#define AUX_NATIVE_REPLY_MASK (0x3 << 4)
+
+#define AUX_I2C_REPLY_ACK (0x0 << 6)
+#define AUX_I2C_REPLY_NACK (0x1 << 6)
+#define AUX_I2C_REPLY_DEFER (0x2 << 6)
+#define AUX_I2C_REPLY_MASK (0x3 << 6)
+
+/* AUX CH addresses */
+#define DP_LINK_BW_SET 0x100
+# define DP_LINK_BW_1_62 0x06
+# define DP_LINK_BW_2_7 0x0a
+
+#define DP_LANE_COUNT_SET 0x101
+# define DP_LANE_COUNT_MASK 0x0f
+# define DP_LANE_COUNT_ENHANCED_FRAME_EN (1 << 7)
+
+#define DP_TRAINING_PATTERN_SET 0x102
+
+# define DP_TRAINING_PATTERN_DISABLE 0
+# define DP_TRAINING_PATTERN_1 1
+# define DP_TRAINING_PATTERN_2 2
+# define DP_TRAINING_PATTERN_MASK 0x3
+
+# define DP_LINK_QUAL_PATTERN_DISABLE (0 << 2)
+# define DP_LINK_QUAL_PATTERN_D10_2 (1 << 2)
+# define DP_LINK_QUAL_PATTERN_ERROR_RATE (2 << 2)
+# define DP_LINK_QUAL_PATTERN_PRBS7 (3 << 2)
+# define DP_LINK_QUAL_PATTERN_MASK (3 << 2)
+
+# define DP_RECOVERED_CLOCK_OUT_EN (1 << 4)
+# define DP_LINK_SCRAMBLING_DISABLE (1 << 5)
+
+# define DP_SYMBOL_ERROR_COUNT_BOTH (0 << 6)
+# define DP_SYMBOL_ERROR_COUNT_DISPARITY (1 << 6)
+# define DP_SYMBOL_ERROR_COUNT_SYMBOL (2 << 6)
+# define DP_SYMBOL_ERROR_COUNT_MASK (3 << 6)
+
+#define DP_TRAINING_LANE0_SET 0x103
+#define DP_TRAINING_LANE1_SET 0x104
+#define DP_TRAINING_LANE2_SET 0x105
+#define DP_TRAINING_LANE3_SET 0x106
+
+# define DP_TRAIN_VOLTAGE_SWING_MASK 0x3
+# define DP_TRAIN_VOLTAGE_SWING_SHIFT 0
+# define DP_TRAIN_MAX_SWING_REACHED (1 << 2)
+# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+# define DP_TRAIN_VOLTAGE_SWING_600 (1 << 0)
+# define DP_TRAIN_VOLTAGE_SWING_800 (2 << 0)
+# define DP_TRAIN_VOLTAGE_SWING_1200 (3 << 0)
+
+# define DP_TRAIN_PRE_EMPHASIS_MASK (3 << 3)
+# define DP_TRAIN_PRE_EMPHASIS_0 (0 << 3)
+# define DP_TRAIN_PRE_EMPHASIS_3_5 (1 << 3)
+# define DP_TRAIN_PRE_EMPHASIS_6 (2 << 3)
+# define DP_TRAIN_PRE_EMPHASIS_9_5 (3 << 3)
+
+# define DP_TRAIN_PRE_EMPHASIS_SHIFT 3
+# define DP_TRAIN_MAX_PRE_EMPHASIS_REACHED (1 << 5)
+
+#define DP_DOWNSPREAD_CTRL 0x107
+# define DP_SPREAD_AMP_0_5 (1 << 4)
+
+#define DP_MAIN_LINK_CHANNEL_CODING_SET 0x108
+# define DP_SET_ANSI_8B10B (1 << 0)
+
+#define DP_LANE0_1_STATUS 0x202
+#define DP_LANE2_3_STATUS 0x203
+
+# define DP_LANE_CR_DONE (1 << 0)
+# define DP_LANE_CHANNEL_EQ_DONE (1 << 1)
+# define DP_LANE_SYMBOL_LOCKED (1 << 2)
+
+#define DP_LANE_ALIGN_STATUS_UPDATED 0x204
+
+#define DP_INTERLANE_ALIGN_DONE (1 << 0)
+#define DP_DOWNSTREAM_PORT_STATUS_CHANGED (1 << 6)
+#define DP_LINK_STATUS_UPDATED (1 << 7)
+
+#define DP_SINK_STATUS 0x205
+
+#define DP_RECEIVE_PORT_0_STATUS (1 << 0)
+#define DP_RECEIVE_PORT_1_STATUS (1 << 1)
+
+#define DP_ADJUST_REQUEST_LANE0_1 0x206
+#define DP_ADJUST_REQUEST_LANE2_3 0x207
+
+#define DP_ADJUST_VOLTAGE_SWING_LANE0_MASK 0x03
+#define DP_ADJUST_VOLTAGE_SWING_LANE0_SHIFT 0
+#define DP_ADJUST_PRE_EMPHASIS_LANE0_MASK 0x0c
+#define DP_ADJUST_PRE_EMPHASIS_LANE0_SHIFT 2
+#define DP_ADJUST_VOLTAGE_SWING_LANE1_MASK 0x30
+#define DP_ADJUST_VOLTAGE_SWING_LANE1_SHIFT 4
+#define DP_ADJUST_PRE_EMPHASIS_LANE1_MASK 0xc0
+#define DP_ADJUST_PRE_EMPHASIS_LANE1_SHIFT 6
+
+struct i2c_algo_dp_aux_data {
+ bool running;
+ u16 address;
+ int (*aux_ch) (struct i2c_adapter *adapter,
+ uint8_t *send, int send_bytes,
+ uint8_t *recv, int recv_bytes);
+};
+
+int
+i2c_dp_aux_add_bus(struct i2c_adapter *adapter);
+
+#endif /* _INTEL_DP_H_ */
--- /dev/null
+/*
+ * Copyright © 2009 Keith Packard
+ *
+ * Permission to use, copy, modify, distribute, and sell this software and its
+ * documentation for any purpose is hereby granted without fee, provided that
+ * the above copyright notice appear in all copies and that both that copyright
+ * notice and this permission notice appear in supporting documentation, and
+ * that the name of the copyright holders not be used in advertising or
+ * publicity pertaining to distribution of the software without specific,
+ * written prior permission. The copyright holders make no representations
+ * about the suitability of this software for any purpose. It is provided "as
+ * is" without express or implied warranty.
+ *
+ * THE COPYRIGHT HOLDERS DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE,
+ * INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO
+ * EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
+ * CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE,
+ * DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
+ * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
+ * OF THIS SOFTWARE.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/sched.h>
+#include <linux/i2c.h>
+#include "intel_dp.h"
+
+/* Run a single AUX_CH I2C transaction, writing/reading data as necessary */
+
+#define MODE_I2C_START 1
+#define MODE_I2C_WRITE 2
+#define MODE_I2C_READ 4
+#define MODE_I2C_STOP 8
+
+static int
+i2c_algo_dp_aux_transaction(struct i2c_adapter *adapter, int mode,
+ uint8_t write_byte, uint8_t *read_byte)
+{
+ struct i2c_algo_dp_aux_data *algo_data = adapter->algo_data;
+ uint16_t address = algo_data->address;
+ uint8_t msg[5];
+ uint8_t reply[2];
+ int msg_bytes;
+ int reply_bytes;
+ int ret;
+
+ /* Set up the command byte */
+ if (mode & MODE_I2C_READ)
+ msg[0] = AUX_I2C_READ << 4;
+ else
+ msg[0] = AUX_I2C_WRITE << 4;
+
+ if (!(mode & MODE_I2C_STOP))
+ msg[0] |= AUX_I2C_MOT << 4;
+
+ msg[1] = address >> 8;
+ msg[2] = address;
+
+ switch (mode) {
+ case MODE_I2C_WRITE:
+ msg[3] = 0;
+ msg[4] = write_byte;
+ msg_bytes = 5;
+ reply_bytes = 1;
+ break;
+ case MODE_I2C_READ:
+ msg[3] = 0;
+ msg_bytes = 4;
+ reply_bytes = 2;
+ break;
+ default:
+ msg_bytes = 3;
+ reply_bytes = 1;
+ break;
+ }
+
+ for (;;) {
+ ret = (*algo_data->aux_ch)(adapter,
+ msg, msg_bytes,
+ reply, reply_bytes);
+ if (ret < 0) {
+ printk(KERN_ERR "aux_ch failed %d\n", ret);
+ return ret;
+ }
+ switch (reply[0] & AUX_I2C_REPLY_MASK) {
+ case AUX_I2C_REPLY_ACK:
+ if (mode == MODE_I2C_READ) {
+ *read_byte = reply[1];
+ }
+ return reply_bytes - 1;
+ case AUX_I2C_REPLY_NACK:
+ printk(KERN_ERR "aux_ch nack\n");
+ return -EREMOTEIO;
+ case AUX_I2C_REPLY_DEFER:
+ printk(KERN_ERR "aux_ch defer\n");
+ udelay(100);
+ break;
+ default:
+ printk(KERN_ERR "aux_ch invalid reply 0x%02x\n", reply[0]);
+ return -EREMOTEIO;
+ }
+ }
+}
+
+/*
+ * I2C over AUX CH
+ */
+
+/*
+ * Send the address. If the I2C link is running, this 'restarts'
+ * the connection with the new address, this is used for doing
+ * a write followed by a read (as needed for DDC)
+ */
+static int
+i2c_algo_dp_aux_address(struct i2c_adapter *adapter, u16 address, bool reading)
+{
+ struct i2c_algo_dp_aux_data *algo_data = adapter->algo_data;
+ int mode = MODE_I2C_START;
+ int ret;
+
+ if (reading)
+ mode |= MODE_I2C_READ;
+ else
+ mode |= MODE_I2C_WRITE;
+ algo_data->address = address;
+ algo_data->running = true;
+ ret = i2c_algo_dp_aux_transaction(adapter, mode, 0, NULL);
+ return ret;
+}
+
+/*
+ * Stop the I2C transaction. This closes out the link, sending
+ * a bare address packet with the MOT bit turned off
+ */
+static void
+i2c_algo_dp_aux_stop(struct i2c_adapter *adapter, bool reading)
+{
+ struct i2c_algo_dp_aux_data *algo_data = adapter->algo_data;
+ int mode = MODE_I2C_STOP;
+
+ if (reading)
+ mode |= MODE_I2C_READ;
+ else
+ mode |= MODE_I2C_WRITE;
+ if (algo_data->running) {
+ (void) i2c_algo_dp_aux_transaction(adapter, mode, 0, NULL);
+ algo_data->running = false;
+ }
+}
+
+/*
+ * Write a single byte to the current I2C address, the
+ * the I2C link must be running or this returns -EIO
+ */
+static int
+i2c_algo_dp_aux_put_byte(struct i2c_adapter *adapter, u8 byte)
+{
+ struct i2c_algo_dp_aux_data *algo_data = adapter->algo_data;
+ int ret;
+
+ if (!algo_data->running)
+ return -EIO;
+
+ ret = i2c_algo_dp_aux_transaction(adapter, MODE_I2C_WRITE, byte, NULL);
+ return ret;
+}
+
+/*
+ * Read a single byte from the current I2C address, the
+ * I2C link must be running or this returns -EIO
+ */
+static int
+i2c_algo_dp_aux_get_byte(struct i2c_adapter *adapter, u8 *byte_ret)
+{
+ struct i2c_algo_dp_aux_data *algo_data = adapter->algo_data;
+ int ret;
+
+ if (!algo_data->running)
+ return -EIO;
+
+ ret = i2c_algo_dp_aux_transaction(adapter, MODE_I2C_READ, 0, byte_ret);
+ return ret;
+}
+
+static int
+i2c_algo_dp_aux_xfer(struct i2c_adapter *adapter,
+ struct i2c_msg *msgs,
+ int num)
+{
+ int ret = 0;
+ bool reading = false;
+ int m;
+ int b;
+
+ for (m = 0; m < num; m++) {
+ u16 len = msgs[m].len;
+ u8 *buf = msgs[m].buf;
+ reading = (msgs[m].flags & I2C_M_RD) != 0;
+ ret = i2c_algo_dp_aux_address(adapter, msgs[m].addr, reading);
+ if (ret < 0)
+ break;
+ if (reading) {
+ for (b = 0; b < len; b++) {
+ ret = i2c_algo_dp_aux_get_byte(adapter, &buf[b]);
+ if (ret < 0)
+ break;
+ }
+ } else {
+ for (b = 0; b < len; b++) {
+ ret = i2c_algo_dp_aux_put_byte(adapter, buf[b]);
+ if (ret < 0)
+ break;
+ }
+ }
+ if (ret < 0)
+ break;
+ }
+ if (ret >= 0)
+ ret = num;
+ i2c_algo_dp_aux_stop(adapter, reading);
+ printk(KERN_ERR "dp_aux_xfer return %d\n", ret);
+ return ret;
+}
+
+static u32
+i2c_algo_dp_aux_functionality(struct i2c_adapter *adapter)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL |
+ I2C_FUNC_SMBUS_READ_BLOCK_DATA |
+ I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
+ I2C_FUNC_10BIT_ADDR;
+}
+
+static const struct i2c_algorithm i2c_dp_aux_algo = {
+ .master_xfer = i2c_algo_dp_aux_xfer,
+ .functionality = i2c_algo_dp_aux_functionality,
+};
+
+static void
+i2c_dp_aux_reset_bus(struct i2c_adapter *adapter)
+{
+ (void) i2c_algo_dp_aux_address(adapter, 0, false);
+ (void) i2c_algo_dp_aux_stop(adapter, false);
+
+}
+
+static int
+i2c_dp_aux_prepare_bus(struct i2c_adapter *adapter)
+{
+ adapter->algo = &i2c_dp_aux_algo;
+ adapter->retries = 3;
+ i2c_dp_aux_reset_bus(adapter);
+ return 0;
+}
+
+int
+i2c_dp_aux_add_bus(struct i2c_adapter *adapter)
+{
+ int error;
+
+ error = i2c_dp_aux_prepare_bus(adapter);
+ if (error)
+ return error;
+ error = i2c_add_adapter(adapter);
+ return error;
+}
+EXPORT_SYMBOL(i2c_dp_aux_add_bus);
#define INTEL_OUTPUT_LVDS 4
#define INTEL_OUTPUT_TVOUT 5
#define INTEL_OUTPUT_HDMI 6
+#define INTEL_OUTPUT_DISPLAYPORT 7
#define INTEL_DVO_CHIP_NONE 0
#define INTEL_DVO_CHIP_LVDS 1
u32 reg; /* GPIO reg */
struct i2c_adapter adapter;
struct i2c_algo_bit_data algo;
- u8 slave_addr;
};
struct intel_framebuffer {
struct drm_encoder enc;
int type;
- struct intel_i2c_chan *i2c_bus; /* for control functions */
- struct intel_i2c_chan *ddc_bus; /* for DDC only stuff */
+ struct i2c_adapter *i2c_bus;
+ struct i2c_adapter *ddc_bus;
bool load_detect_temp;
bool needs_tv_clock;
void *dev_priv;
+ void (*hot_plug)(struct intel_output *);
};
struct intel_crtc {
#define enc_to_intel_output(x) container_of(x, struct intel_output, enc)
#define to_intel_framebuffer(x) container_of(x, struct intel_framebuffer, base)
-struct intel_i2c_chan *intel_i2c_create(struct drm_device *dev, const u32 reg,
- const char *name);
-void intel_i2c_destroy(struct intel_i2c_chan *chan);
+struct i2c_adapter *intel_i2c_create(struct drm_device *dev, const u32 reg,
+ const char *name);
+void intel_i2c_destroy(struct i2c_adapter *adapter);
int intel_ddc_get_modes(struct intel_output *intel_output);
extern bool intel_ddc_probe(struct intel_output *intel_output);
void intel_i2c_quirk_set(struct drm_device *dev, bool enable);
extern void intel_dvo_init(struct drm_device *dev);
extern void intel_tv_init(struct drm_device *dev);
extern void intel_lvds_init(struct drm_device *dev);
+extern void intel_dp_init(struct drm_device *dev, int dp_reg);
+void
+intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode);
extern void intel_crtc_load_lut(struct drm_crtc *crtc);
extern void intel_encoder_prepare (struct drm_encoder *encoder);
{
struct intel_output *intel_output;
struct intel_dvo_device *dvo;
- struct intel_i2c_chan *i2cbus = NULL;
+ struct i2c_adapter *i2cbus = NULL;
int ret = 0;
int i;
- int gpio_inited = 0;
int encoder_type = DRM_MODE_ENCODER_NONE;
intel_output = kzalloc (sizeof(struct intel_output), GFP_KERNEL);
if (!intel_output)
* It appears that everything is on GPIOE except for panels
* on i830 laptops, which are on GPIOB (DVOA).
*/
- if (gpio_inited != gpio) {
- if (i2cbus != NULL)
- intel_i2c_destroy(i2cbus);
- if (!(i2cbus = intel_i2c_create(dev, gpio,
- gpio == GPIOB ? "DVOI2C_B" : "DVOI2C_E"))) {
- continue;
- }
- gpio_inited = gpio;
+ if (i2cbus != NULL)
+ intel_i2c_destroy(i2cbus);
+ if (!(i2cbus = intel_i2c_create(dev, gpio,
+ gpio == GPIOB ? "DVOI2C_B" : "DVOI2C_E"))) {
+ continue;
}
if (dvo->dev_ops!= NULL)
#include "drmP.h"
#include "drm.h"
#include "drm_crtc.h"
+#include "drm_edid.h"
#include "intel_drv.h"
#include "i915_drm.h"
#include "i915_drv.h"
sdvox = SDVO_ENCODING_HDMI |
SDVO_BORDER_ENABLE |
SDVO_VSYNC_ACTIVE_HIGH |
- SDVO_HSYNC_ACTIVE_HIGH |
- SDVO_NULL_PACKETS_DURING_VSYNC;
+ SDVO_HSYNC_ACTIVE_HIGH;
if (hdmi_priv->has_hdmi_sink)
sdvox |= SDVO_AUDIO_ENABLE;
return true;
}
-static void
-intel_hdmi_sink_detect(struct drm_connector *connector)
+static enum drm_connector_status
+intel_hdmi_edid_detect(struct drm_connector *connector)
{
struct intel_output *intel_output = to_intel_output(connector);
struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv;
struct edid *edid = NULL;
+ enum drm_connector_status status = connector_status_disconnected;
edid = drm_get_edid(&intel_output->base,
- &intel_output->ddc_bus->adapter);
- if (edid != NULL) {
- hdmi_priv->has_hdmi_sink = drm_detect_hdmi_monitor(edid);
- kfree(edid);
+ intel_output->ddc_bus);
+ hdmi_priv->has_hdmi_sink = false;
+ if (edid) {
+ if (edid->input & DRM_EDID_INPUT_DIGITAL) {
+ status = connector_status_connected;
+ hdmi_priv->has_hdmi_sink = drm_detect_hdmi_monitor(edid);
+ }
intel_output->base.display_info.raw_edid = NULL;
+ kfree(edid);
}
+ return status;
}
static enum drm_connector_status
/* FIXME hotplug detect */
hdmi_priv->has_hdmi_sink = false;
- intel_hdmi_sink_detect(connector);
- if (hdmi_priv->has_hdmi_sink)
- return connector_status_connected;
- else
- return connector_status_disconnected;
+ return intel_hdmi_edid_detect(connector);
}
static enum drm_connector_status
return connector_status_unknown;
}
- if ((I915_READ(PORT_HOTPLUG_STAT) & bit) != 0) {
- intel_hdmi_sink_detect(connector);
- return connector_status_connected;
- } else
+ if ((I915_READ(PORT_HOTPLUG_STAT) & bit) != 0)
+ return intel_hdmi_edid_detect(connector);
+ else
return connector_status_disconnected;
}
* @output: driver specific output device
* @reg: GPIO reg to use
* @name: name for this bus
+ * @slave_addr: slave address (if fixed)
*
* Creates and registers a new i2c bus with the Linux i2c layer, for use
* in output probing and control (e.g. DDC or SDVO control functions).
* %GPIOH
* see PRM for details on how these different busses are used.
*/
-struct intel_i2c_chan *intel_i2c_create(struct drm_device *dev, const u32 reg,
- const char *name)
+struct i2c_adapter *intel_i2c_create(struct drm_device *dev, const u32 reg,
+ const char *name)
{
struct intel_i2c_chan *chan;
intel_i2c_quirk_set(dev, false);
udelay(20);
- return chan;
+ return &chan->adapter;
out_free:
kfree(chan);
*
* Unregister the adapter from the i2c layer, then free the structure.
*/
-void intel_i2c_destroy(struct intel_i2c_chan *chan)
+void intel_i2c_destroy(struct i2c_adapter *adapter)
{
- if (!chan)
+ struct intel_i2c_chan *chan;
+
+ if (!adapter)
return;
+ chan = container_of(adapter,
+ struct intel_i2c_chan,
+ adapter);
i2c_del_adapter(&chan->adapter);
kfree(chan);
}
#define I915_LVDS "i915_lvds"
+/*
+ * the following four scaling options are defined.
+ * #define DRM_MODE_SCALE_NON_GPU 0
+ * #define DRM_MODE_SCALE_FULLSCREEN 1
+ * #define DRM_MODE_SCALE_NO_SCALE 2
+ * #define DRM_MODE_SCALE_ASPECT 3
+ */
+
+/* Private structure for the integrated LVDS support */
+struct intel_lvds_priv {
+ int fitting_mode;
+ u32 pfit_control;
+ u32 pfit_pgm_ratios;
+};
+
/**
* Sets the backlight level.
*
struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
+ /*
+ * float point operation is not supported . So the PANEL_RATIO_FACTOR
+ * is defined, which can avoid the float point computation when
+ * calculating the panel ratio.
+ */
+#define PANEL_RATIO_FACTOR 8192
struct drm_device *dev = encoder->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
struct drm_encoder *tmp_encoder;
+ struct intel_output *intel_output = enc_to_intel_output(encoder);
+ struct intel_lvds_priv *lvds_priv = intel_output->dev_priv;
+ u32 pfit_control = 0, pfit_pgm_ratios = 0;
+ int left_border = 0, right_border = 0, top_border = 0;
+ int bottom_border = 0;
+ bool border = 0;
+ int panel_ratio, desired_ratio, vert_scale, horiz_scale;
+ int horiz_ratio, vert_ratio;
+ u32 hsync_width, vsync_width;
+ u32 hblank_width, vblank_width;
+ u32 hsync_pos, vsync_pos;
/* Should never happen!! */
if (!IS_I965G(dev) && intel_crtc->pipe == 0) {
return false;
}
}
-
+ /* If we don't have a panel mode, there is nothing we can do */
+ if (dev_priv->panel_fixed_mode == NULL)
+ return true;
/*
* If we have timings from the BIOS for the panel, put them in
* to the adjusted mode. The CRTC will be set up for this mode,
drm_mode_set_crtcinfo(adjusted_mode, CRTC_INTERLACE_HALVE_V);
}
+ /* Make sure pre-965s set dither correctly */
+ if (!IS_I965G(dev)) {
+ if (dev_priv->panel_wants_dither || dev_priv->lvds_dither)
+ pfit_control |= PANEL_8TO6_DITHER_ENABLE;
+ }
+
+ /* Native modes don't need fitting */
+ if (adjusted_mode->hdisplay == mode->hdisplay &&
+ adjusted_mode->vdisplay == mode->vdisplay) {
+ pfit_pgm_ratios = 0;
+ border = 0;
+ goto out;
+ }
+
+ /* 965+ wants fuzzy fitting */
+ if (IS_I965G(dev))
+ pfit_control |= (intel_crtc->pipe << PFIT_PIPE_SHIFT) |
+ PFIT_FILTER_FUZZY;
+
+ hsync_width = adjusted_mode->crtc_hsync_end -
+ adjusted_mode->crtc_hsync_start;
+ vsync_width = adjusted_mode->crtc_vsync_end -
+ adjusted_mode->crtc_vsync_start;
+ hblank_width = adjusted_mode->crtc_hblank_end -
+ adjusted_mode->crtc_hblank_start;
+ vblank_width = adjusted_mode->crtc_vblank_end -
+ adjusted_mode->crtc_vblank_start;
+ /*
+ * Deal with panel fitting options. Figure out how to stretch the
+ * image based on its aspect ratio & the current panel fitting mode.
+ */
+ panel_ratio = adjusted_mode->hdisplay * PANEL_RATIO_FACTOR /
+ adjusted_mode->vdisplay;
+ desired_ratio = mode->hdisplay * PANEL_RATIO_FACTOR /
+ mode->vdisplay;
+ /*
+ * Enable automatic panel scaling for non-native modes so that they fill
+ * the screen. Should be enabled before the pipe is enabled, according
+ * to register description and PRM.
+ * Change the value here to see the borders for debugging
+ */
+ I915_WRITE(BCLRPAT_A, 0);
+ I915_WRITE(BCLRPAT_B, 0);
+
+ switch (lvds_priv->fitting_mode) {
+ case DRM_MODE_SCALE_NO_SCALE:
+ /*
+ * For centered modes, we have to calculate border widths &
+ * heights and modify the values programmed into the CRTC.
+ */
+ left_border = (adjusted_mode->hdisplay - mode->hdisplay) / 2;
+ right_border = left_border;
+ if (mode->hdisplay & 1)
+ right_border++;
+ top_border = (adjusted_mode->vdisplay - mode->vdisplay) / 2;
+ bottom_border = top_border;
+ if (mode->vdisplay & 1)
+ bottom_border++;
+ /* Set active & border values */
+ adjusted_mode->crtc_hdisplay = mode->hdisplay;
+ /* Keep the boder be even */
+ if (right_border & 1)
+ right_border++;
+ /* use the border directly instead of border minuse one */
+ adjusted_mode->crtc_hblank_start = mode->hdisplay +
+ right_border;
+ /* keep the blank width constant */
+ adjusted_mode->crtc_hblank_end =
+ adjusted_mode->crtc_hblank_start + hblank_width;
+ /* get the hsync pos relative to hblank start */
+ hsync_pos = (hblank_width - hsync_width) / 2;
+ /* keep the hsync pos be even */
+ if (hsync_pos & 1)
+ hsync_pos++;
+ adjusted_mode->crtc_hsync_start =
+ adjusted_mode->crtc_hblank_start + hsync_pos;
+ /* keep the hsync width constant */
+ adjusted_mode->crtc_hsync_end =
+ adjusted_mode->crtc_hsync_start + hsync_width;
+ adjusted_mode->crtc_vdisplay = mode->vdisplay;
+ /* use the border instead of border minus one */
+ adjusted_mode->crtc_vblank_start = mode->vdisplay +
+ bottom_border;
+ /* keep the vblank width constant */
+ adjusted_mode->crtc_vblank_end =
+ adjusted_mode->crtc_vblank_start + vblank_width;
+ /* get the vsync start postion relative to vblank start */
+ vsync_pos = (vblank_width - vsync_width) / 2;
+ adjusted_mode->crtc_vsync_start =
+ adjusted_mode->crtc_vblank_start + vsync_pos;
+ /* keep the vsync width constant */
+ adjusted_mode->crtc_vsync_end =
+ adjusted_mode->crtc_vblank_start + vsync_width;
+ border = 1;
+ break;
+ case DRM_MODE_SCALE_ASPECT:
+ /* Scale but preserve the spect ratio */
+ pfit_control |= PFIT_ENABLE;
+ if (IS_I965G(dev)) {
+ /* 965+ is easy, it does everything in hw */
+ if (panel_ratio > desired_ratio)
+ pfit_control |= PFIT_SCALING_PILLAR;
+ else if (panel_ratio < desired_ratio)
+ pfit_control |= PFIT_SCALING_LETTER;
+ else
+ pfit_control |= PFIT_SCALING_AUTO;
+ } else {
+ /*
+ * For earlier chips we have to calculate the scaling
+ * ratio by hand and program it into the
+ * PFIT_PGM_RATIO register
+ */
+ u32 horiz_bits, vert_bits, bits = 12;
+ horiz_ratio = mode->hdisplay * PANEL_RATIO_FACTOR/
+ adjusted_mode->hdisplay;
+ vert_ratio = mode->vdisplay * PANEL_RATIO_FACTOR/
+ adjusted_mode->vdisplay;
+ horiz_scale = adjusted_mode->hdisplay *
+ PANEL_RATIO_FACTOR / mode->hdisplay;
+ vert_scale = adjusted_mode->vdisplay *
+ PANEL_RATIO_FACTOR / mode->vdisplay;
+
+ /* retain aspect ratio */
+ if (panel_ratio > desired_ratio) { /* Pillar */
+ u32 scaled_width;
+ scaled_width = mode->hdisplay * vert_scale /
+ PANEL_RATIO_FACTOR;
+ horiz_ratio = vert_ratio;
+ pfit_control |= (VERT_AUTO_SCALE |
+ VERT_INTERP_BILINEAR |
+ HORIZ_INTERP_BILINEAR);
+ /* Pillar will have left/right borders */
+ left_border = (adjusted_mode->hdisplay -
+ scaled_width) / 2;
+ right_border = left_border;
+ if (mode->hdisplay & 1) /* odd resolutions */
+ right_border++;
+ /* keep the border be even */
+ if (right_border & 1)
+ right_border++;
+ adjusted_mode->crtc_hdisplay = scaled_width;
+ /* use border instead of border minus one */
+ adjusted_mode->crtc_hblank_start =
+ scaled_width + right_border;
+ /* keep the hblank width constant */
+ adjusted_mode->crtc_hblank_end =
+ adjusted_mode->crtc_hblank_start +
+ hblank_width;
+ /*
+ * get the hsync start pos relative to
+ * hblank start
+ */
+ hsync_pos = (hblank_width - hsync_width) / 2;
+ /* keep the hsync_pos be even */
+ if (hsync_pos & 1)
+ hsync_pos++;
+ adjusted_mode->crtc_hsync_start =
+ adjusted_mode->crtc_hblank_start +
+ hsync_pos;
+ /* keept hsync width constant */
+ adjusted_mode->crtc_hsync_end =
+ adjusted_mode->crtc_hsync_start +
+ hsync_width;
+ border = 1;
+ } else if (panel_ratio < desired_ratio) { /* letter */
+ u32 scaled_height = mode->vdisplay *
+ horiz_scale / PANEL_RATIO_FACTOR;
+ vert_ratio = horiz_ratio;
+ pfit_control |= (HORIZ_AUTO_SCALE |
+ VERT_INTERP_BILINEAR |
+ HORIZ_INTERP_BILINEAR);
+ /* Letterbox will have top/bottom border */
+ top_border = (adjusted_mode->vdisplay -
+ scaled_height) / 2;
+ bottom_border = top_border;
+ if (mode->vdisplay & 1)
+ bottom_border++;
+ adjusted_mode->crtc_vdisplay = scaled_height;
+ /* use border instead of border minus one */
+ adjusted_mode->crtc_vblank_start =
+ scaled_height + bottom_border;
+ /* keep the vblank width constant */
+ adjusted_mode->crtc_vblank_end =
+ adjusted_mode->crtc_vblank_start +
+ vblank_width;
+ /*
+ * get the vsync start pos relative to
+ * vblank start
+ */
+ vsync_pos = (vblank_width - vsync_width) / 2;
+ adjusted_mode->crtc_vsync_start =
+ adjusted_mode->crtc_vblank_start +
+ vsync_pos;
+ /* keep the vsync width constant */
+ adjusted_mode->crtc_vsync_end =
+ adjusted_mode->crtc_vsync_start +
+ vsync_width;
+ border = 1;
+ } else {
+ /* Aspects match, Let hw scale both directions */
+ pfit_control |= (VERT_AUTO_SCALE |
+ HORIZ_AUTO_SCALE |
+ VERT_INTERP_BILINEAR |
+ HORIZ_INTERP_BILINEAR);
+ }
+ horiz_bits = (1 << bits) * horiz_ratio /
+ PANEL_RATIO_FACTOR;
+ vert_bits = (1 << bits) * vert_ratio /
+ PANEL_RATIO_FACTOR;
+ pfit_pgm_ratios =
+ ((vert_bits << PFIT_VERT_SCALE_SHIFT) &
+ PFIT_VERT_SCALE_MASK) |
+ ((horiz_bits << PFIT_HORIZ_SCALE_SHIFT) &
+ PFIT_HORIZ_SCALE_MASK);
+ }
+ break;
+
+ case DRM_MODE_SCALE_FULLSCREEN:
+ /*
+ * Full scaling, even if it changes the aspect ratio.
+ * Fortunately this is all done for us in hw.
+ */
+ pfit_control |= PFIT_ENABLE;
+ if (IS_I965G(dev))
+ pfit_control |= PFIT_SCALING_AUTO;
+ else
+ pfit_control |= (VERT_AUTO_SCALE | HORIZ_AUTO_SCALE |
+ VERT_INTERP_BILINEAR |
+ HORIZ_INTERP_BILINEAR);
+ break;
+ default:
+ break;
+ }
+
+out:
+ lvds_priv->pfit_control = pfit_control;
+ lvds_priv->pfit_pgm_ratios = pfit_pgm_ratios;
/*
* XXX: It would be nice to support lower refresh rates on the
* panels to reduce power consumption, and perhaps match the
{
struct drm_device *dev = encoder->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
- u32 pfit_control;
+ struct intel_output *intel_output = enc_to_intel_output(encoder);
+ struct intel_lvds_priv *lvds_priv = intel_output->dev_priv;
/*
* The LVDS pin pair will already have been turned on in the
* screen. Should be enabled before the pipe is enabled, according to
* register description and PRM.
*/
- if (mode->hdisplay != adjusted_mode->hdisplay ||
- mode->vdisplay != adjusted_mode->vdisplay)
- pfit_control = (PFIT_ENABLE | VERT_AUTO_SCALE |
- HORIZ_AUTO_SCALE | VERT_INTERP_BILINEAR |
- HORIZ_INTERP_BILINEAR);
- else
- pfit_control = 0;
-
- if (!IS_I965G(dev)) {
- if (dev_priv->panel_wants_dither || dev_priv->lvds_dither)
- pfit_control |= PANEL_8TO6_DITHER_ENABLE;
- }
- else
- pfit_control |= intel_crtc->pipe << PFIT_PIPE_SHIFT;
-
- I915_WRITE(PFIT_CONTROL, pfit_control);
+ I915_WRITE(PFIT_PGM_RATIOS, lvds_priv->pfit_pgm_ratios);
+ I915_WRITE(PFIT_CONTROL, lvds_priv->pfit_control);
}
/**
struct drm_property *property,
uint64_t value)
{
+ struct drm_device *dev = connector->dev;
+ struct intel_output *intel_output =
+ to_intel_output(connector);
+
+ if (property == dev->mode_config.scaling_mode_property &&
+ connector->encoder) {
+ struct drm_crtc *crtc = connector->encoder->crtc;
+ struct intel_lvds_priv *lvds_priv = intel_output->dev_priv;
+ if (value == DRM_MODE_SCALE_NON_GPU) {
+ DRM_DEBUG_KMS(I915_LVDS,
+ "non_GPU property is unsupported\n");
+ return 0;
+ }
+ if (lvds_priv->fitting_mode == value) {
+ /* the LVDS scaling property is not changed */
+ return 0;
+ }
+ lvds_priv->fitting_mode = value;
+ if (crtc && crtc->enabled) {
+ /*
+ * If the CRTC is enabled, the display will be changed
+ * according to the new panel fitting mode.
+ */
+ drm_crtc_helper_set_mode(crtc, &crtc->mode,
+ crtc->x, crtc->y, crtc->fb);
+ }
+ }
+
return 0;
}
.callback = intel_no_lvds_dmi_callback,
.ident = "Apple Mac Mini (Core series)",
.matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+ DMI_MATCH(DMI_SYS_VENDOR, "Apple"),
DMI_MATCH(DMI_PRODUCT_NAME, "Macmini1,1"),
},
},
.callback = intel_no_lvds_dmi_callback,
.ident = "Apple Mac Mini (Core 2 series)",
.matches = {
- DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+ DMI_MATCH(DMI_SYS_VENDOR, "Apple"),
DMI_MATCH(DMI_PRODUCT_NAME, "Macmini2,1"),
},
},
struct drm_encoder *encoder;
struct drm_display_mode *scan; /* *modes, *bios_mode; */
struct drm_crtc *crtc;
+ struct intel_lvds_priv *lvds_priv;
u32 lvds;
int pipe, gpio = GPIOC;
gpio = PCH_GPIOC;
}
- intel_output = kzalloc(sizeof(struct intel_output), GFP_KERNEL);
+ intel_output = kzalloc(sizeof(struct intel_output) +
+ sizeof(struct intel_lvds_priv), GFP_KERNEL);
if (!intel_output) {
return;
}
connector->interlace_allowed = false;
connector->doublescan_allowed = false;
+ lvds_priv = (struct intel_lvds_priv *)(intel_output + 1);
+ intel_output->dev_priv = lvds_priv;
+ /* create the scaling mode property */
+ drm_mode_create_scaling_mode_property(dev);
+ /*
+ * the initial panel fitting mode will be FULL_SCREEN.
+ */
+ drm_connector_attach_property(&intel_output->base,
+ dev->mode_config.scaling_mode_property,
+ DRM_MODE_SCALE_FULLSCREEN);
+ lvds_priv->fitting_mode = DRM_MODE_SCALE_FULLSCREEN;
/*
* LVDS discovery:
* 1) check for EDID on DDC
if (intel_output->ddc_bus)
intel_i2c_destroy(intel_output->ddc_bus);
drm_connector_cleanup(connector);
- kfree(connector);
+ kfree(intel_output);
}
}
};
- intel_i2c_quirk_set(intel_output->ddc_bus->drm_dev, true);
- ret = i2c_transfer(&intel_output->ddc_bus->adapter, msgs, 2);
- intel_i2c_quirk_set(intel_output->ddc_bus->drm_dev, false);
-
+ intel_i2c_quirk_set(intel_output->base.dev, true);
+ ret = i2c_transfer(intel_output->ddc_bus, msgs, 2);
+ intel_i2c_quirk_set(intel_output->base.dev, false);
if (ret == 2)
return true;
struct edid *edid;
int ret = 0;
- intel_i2c_quirk_set(intel_output->ddc_bus->drm_dev, true);
- edid = drm_get_edid(&intel_output->base,
- &intel_output->ddc_bus->adapter);
- intel_i2c_quirk_set(intel_output->ddc_bus->drm_dev, false);
+ intel_i2c_quirk_set(intel_output->base.dev, true);
+ edid = drm_get_edid(&intel_output->base, intel_output->ddc_bus);
+ intel_i2c_quirk_set(intel_output->base.dev, false);
if (edid) {
drm_mode_connector_update_edid_property(&intel_output->base,
edid);
#undef SDVO_DEBUG
#define I915_SDVO "i915_sdvo"
struct intel_sdvo_priv {
- struct intel_i2c_chan *i2c_bus;
- int slaveaddr;
+ u8 slave_addr;
/* Register for the SDVO device: SDVOB or SDVOC */
int output_device;
struct i2c_msg msgs[] = {
{
- .addr = sdvo_priv->i2c_bus->slave_addr,
+ .addr = sdvo_priv->slave_addr >> 1,
.flags = 0,
.len = 1,
.buf = out_buf,
},
{
- .addr = sdvo_priv->i2c_bus->slave_addr,
+ .addr = sdvo_priv->slave_addr >> 1,
.flags = I2C_M_RD,
.len = 1,
.buf = buf,
out_buf[0] = addr;
out_buf[1] = 0;
- if ((ret = i2c_transfer(&sdvo_priv->i2c_bus->adapter, msgs, 2)) == 2)
+ if ((ret = i2c_transfer(intel_output->i2c_bus, msgs, 2)) == 2)
{
*ch = buf[0];
return true;
static bool intel_sdvo_write_byte(struct intel_output *intel_output, int addr,
u8 ch)
{
+ struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
u8 out_buf[2];
struct i2c_msg msgs[] = {
{
- .addr = intel_output->i2c_bus->slave_addr,
+ .addr = sdvo_priv->slave_addr >> 1,
.flags = 0,
.len = 2,
.buf = out_buf,
out_buf[0] = addr;
out_buf[1] = ch;
- if (i2c_transfer(&intel_output->i2c_bus->adapter, msgs, 1) == 1)
+ if (i2c_transfer(intel_output->i2c_bus, msgs, 1) == 1)
{
return true;
}
struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
struct edid *edid = NULL;
- intel_sdvo_set_control_bus_switch(intel_output, sdvo_priv->ddc_bus);
edid = drm_get_edid(&intel_output->base,
- &intel_output->ddc_bus->adapter);
+ intel_output->ddc_bus);
if (edid != NULL) {
sdvo_priv->is_hdmi = drm_detect_hdmi_monitor(edid);
kfree(edid);
static void intel_sdvo_get_lvds_modes(struct drm_connector *connector)
{
struct intel_output *intel_output = to_intel_output(connector);
- struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
struct drm_i915_private *dev_priv = connector->dev->dev_private;
/*
* Assume that the preferred modes are
* arranged in priority order.
*/
- /* set the bus switch and get the modes */
- intel_sdvo_set_control_bus_switch(intel_output, sdvo_priv->ddc_bus);
intel_ddc_get_modes(intel_output);
if (list_empty(&connector->probed_modes) == false)
return;
list_for_each_entry(connector,
&dev->mode_config.connector_list, head) {
- if (to_intel_output(connector)->ddc_bus == chan) {
+ if (to_intel_output(connector)->ddc_bus == &chan->adapter) {
intel_output = to_intel_output(connector);
break;
}
struct intel_output *intel_output;
struct intel_sdvo_priv *sdvo_priv;
struct i2c_algo_bit_data *algo_data;
- struct i2c_algorithm *algo;
+ const struct i2c_algorithm *algo;
algo_data = (struct i2c_algo_bit_data *)i2c_adap->algo_data;
intel_output =
return -EINVAL;
sdvo_priv = intel_output->dev_priv;
- algo = (struct i2c_algorithm *)intel_output->i2c_bus->adapter.algo;
+ algo = intel_output->i2c_bus->algo;
intel_sdvo_set_control_bus_switch(intel_output, sdvo_priv->ddc_bus);
return algo->master_xfer(i2c_adap, msgs, num);
struct drm_connector *connector;
struct intel_output *intel_output;
struct intel_sdvo_priv *sdvo_priv;
- struct intel_i2c_chan *i2cbus = NULL;
- struct intel_i2c_chan *ddcbus = NULL;
+
int connector_type;
u8 ch[0x40];
int i;
- int encoder_type, output_id;
- u8 slave_addr;
+ int encoder_type;
intel_output = kcalloc(sizeof(struct intel_output)+sizeof(struct intel_sdvo_priv), 1, GFP_KERNEL);
if (!intel_output) {
}
sdvo_priv = (struct intel_sdvo_priv *)(intel_output + 1);
+ sdvo_priv->output_device = output_device;
+
+ intel_output->dev_priv = sdvo_priv;
intel_output->type = INTEL_OUTPUT_SDVO;
/* setup the DDC bus. */
if (output_device == SDVOB)
- i2cbus = intel_i2c_create(dev, GPIOE, "SDVOCTRL_E for SDVOB");
+ intel_output->i2c_bus = intel_i2c_create(dev, GPIOE, "SDVOCTRL_E for SDVOB");
else
- i2cbus = intel_i2c_create(dev, GPIOE, "SDVOCTRL_E for SDVOC");
+ intel_output->i2c_bus = intel_i2c_create(dev, GPIOE, "SDVOCTRL_E for SDVOC");
- if (!i2cbus)
+ if (!intel_output->i2c_bus)
goto err_inteloutput;
- slave_addr = intel_sdvo_get_slave_addr(dev, output_device);
- sdvo_priv->i2c_bus = i2cbus;
+ sdvo_priv->slave_addr = intel_sdvo_get_slave_addr(dev, output_device);
- if (output_device == SDVOB) {
- output_id = 1;
- } else {
- output_id = 2;
- }
- sdvo_priv->i2c_bus->slave_addr = slave_addr >> 1;
- sdvo_priv->output_device = output_device;
- intel_output->i2c_bus = i2cbus;
- intel_output->dev_priv = sdvo_priv;
+ /* Save the bit-banging i2c functionality for use by the DDC wrapper */
+ intel_sdvo_i2c_bit_algo.functionality = intel_output->i2c_bus->algo->functionality;
/* Read the regs to test if we can talk to the device */
for (i = 0; i < 0x40; i++) {
/* setup the DDC bus. */
if (output_device == SDVOB)
- ddcbus = intel_i2c_create(dev, GPIOE, "SDVOB DDC BUS");
+ intel_output->ddc_bus = intel_i2c_create(dev, GPIOE, "SDVOB DDC BUS");
else
- ddcbus = intel_i2c_create(dev, GPIOE, "SDVOC DDC BUS");
+ intel_output->ddc_bus = intel_i2c_create(dev, GPIOE, "SDVOC DDC BUS");
- if (ddcbus == NULL)
+ if (intel_output->ddc_bus == NULL)
goto err_i2c;
- intel_sdvo_i2c_bit_algo.functionality =
- intel_output->i2c_bus->adapter.algo->functionality;
- ddcbus->adapter.algo = &intel_sdvo_i2c_bit_algo;
- intel_output->ddc_bus = ddcbus;
+ /* Wrap with our custom algo which switches to DDC mode */
+ intel_output->ddc_bus->algo = &intel_sdvo_i2c_bit_algo;
/* In defaut case sdvo lvds is false */
sdvo_priv->is_lvds = false;
return true;
err_i2c:
- if (ddcbus != NULL)
+ if (intel_output->ddc_bus != NULL)
intel_i2c_destroy(intel_output->ddc_bus);
- intel_i2c_destroy(intel_output->i2c_bus);
+ if (intel_output->i2c_bus != NULL)
+ intel_i2c_destroy(intel_output->i2c_bus);
err_inteloutput:
kfree(intel_output);
/*
* Detect TV by polling)
*/
- if (intel_output->load_detect_temp) {
- /* TV not currently running, prod it with destructive detect */
- save_tv_dac = tv_dac;
- tv_ctl = I915_READ(TV_CTL);
- save_tv_ctl = tv_ctl;
- tv_ctl &= ~TV_ENC_ENABLE;
- tv_ctl &= ~TV_TEST_MODE_MASK;
- tv_ctl |= TV_TEST_MODE_MONITOR_DETECT;
- tv_dac &= ~TVDAC_SENSE_MASK;
- tv_dac &= ~DAC_A_MASK;
- tv_dac &= ~DAC_B_MASK;
- tv_dac &= ~DAC_C_MASK;
- tv_dac |= (TVDAC_STATE_CHG_EN |
- TVDAC_A_SENSE_CTL |
- TVDAC_B_SENSE_CTL |
- TVDAC_C_SENSE_CTL |
- DAC_CTL_OVERRIDE |
- DAC_A_0_7_V |
- DAC_B_0_7_V |
- DAC_C_0_7_V);
- I915_WRITE(TV_CTL, tv_ctl);
- I915_WRITE(TV_DAC, tv_dac);
- intel_wait_for_vblank(dev);
- tv_dac = I915_READ(TV_DAC);
- I915_WRITE(TV_DAC, save_tv_dac);
- I915_WRITE(TV_CTL, save_tv_ctl);
- intel_wait_for_vblank(dev);
- }
+ save_tv_dac = tv_dac;
+ tv_ctl = I915_READ(TV_CTL);
+ save_tv_ctl = tv_ctl;
+ tv_ctl &= ~TV_ENC_ENABLE;
+ tv_ctl &= ~TV_TEST_MODE_MASK;
+ tv_ctl |= TV_TEST_MODE_MONITOR_DETECT;
+ tv_dac &= ~TVDAC_SENSE_MASK;
+ tv_dac &= ~DAC_A_MASK;
+ tv_dac &= ~DAC_B_MASK;
+ tv_dac &= ~DAC_C_MASK;
+ tv_dac |= (TVDAC_STATE_CHG_EN |
+ TVDAC_A_SENSE_CTL |
+ TVDAC_B_SENSE_CTL |
+ TVDAC_C_SENSE_CTL |
+ DAC_CTL_OVERRIDE |
+ DAC_A_0_7_V |
+ DAC_B_0_7_V |
+ DAC_C_0_7_V);
+ I915_WRITE(TV_CTL, tv_ctl);
+ I915_WRITE(TV_DAC, tv_dac);
+ intel_wait_for_vblank(dev);
+ tv_dac = I915_READ(TV_DAC);
+ I915_WRITE(TV_DAC, save_tv_dac);
+ I915_WRITE(TV_CTL, save_tv_ctl);
+ intel_wait_for_vblank(dev);
/*
* A B C
* 0 1 1 Composite
#include "radeon_asic.h"
#include "atom.h"
+/*
+ * Clear GPU surface registers.
+ */
+static void radeon_surface_init(struct radeon_device *rdev)
+{
+ /* FIXME: check this out */
+ if (rdev->family < CHIP_R600) {
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ WREG32(RADEON_SURFACE0_INFO +
+ i * (RADEON_SURFACE1_INFO - RADEON_SURFACE0_INFO),
+ 0);
+ }
+ }
+}
+
/*
* GPU scratch registers helpers function.
*/
radeon_errata(rdev);
/* Initialize scratch registers */
radeon_scratch_init(rdev);
+ /* Initialize surface registers */
+ radeon_surface_init(rdev);
/* TODO: disable VGA need to use VGA request */
/* BIOS*/
if (r) {
return r;
}
- if (rdev->fbdev_rfb && rdev->fbdev_rfb->obj) {
- rdev->fbdev_robj = rdev->fbdev_rfb->obj->driver_private;
- }
if (!ret) {
DRM_INFO("radeon: kernel modesetting successfully initialized.\n");
}
drm_exit(driver);
}
-late_initcall(radeon_init);
+module_init(radeon_init);
module_exit(radeon_exit);
MODULE_AUTHOR(DRIVER_AUTHOR);
{
struct fb_info *info;
struct radeon_fb_device *rfbdev;
- struct drm_framebuffer *fb;
+ struct drm_framebuffer *fb = NULL;
struct radeon_framebuffer *rfb;
struct drm_mode_fb_cmd mode_cmd;
struct drm_gem_object *gobj = NULL;
struct radeon_object *robj = NULL;
struct device *device = &rdev->pdev->dev;
int size, aligned_size, ret;
+ u64 fb_gpuaddr;
void *fbptr = NULL;
+ unsigned long tmp;
mode_cmd.width = surface_width;
mode_cmd.height = surface_height;
aligned_size = ALIGN(size, PAGE_SIZE);
ret = radeon_gem_object_create(rdev, aligned_size, 0,
- RADEON_GEM_DOMAIN_VRAM,
- false, ttm_bo_type_kernel,
- false, &gobj);
+ RADEON_GEM_DOMAIN_VRAM,
+ false, ttm_bo_type_kernel,
+ false, &gobj);
if (ret) {
- printk(KERN_ERR "failed to allocate framebuffer\n");
+ printk(KERN_ERR "failed to allocate framebuffer (%d %d)\n",
+ surface_width, surface_height);
ret = -ENOMEM;
goto out;
}
ret = -ENOMEM;
goto out_unref;
}
+ ret = radeon_object_pin(robj, RADEON_GEM_DOMAIN_VRAM, &fb_gpuaddr);
+ if (ret) {
+ printk(KERN_ERR "failed to pin framebuffer\n");
+ ret = -ENOMEM;
+ goto out_unref;
+ }
list_add(&fb->filp_head, &rdev->ddev->mode_config.fb_kernel_list);
rfb = to_radeon_framebuffer(fb);
*rfb_p = rfb;
rdev->fbdev_rfb = rfb;
+ rdev->fbdev_robj = robj;
info = framebuffer_alloc(sizeof(struct radeon_fb_device), device);
if (info == NULL) {
info->fix.xpanstep = 1; /* doing it in hw */
info->fix.ypanstep = 1; /* doing it in hw */
info->fix.ywrapstep = 0;
- info->fix.accel = FB_ACCEL_I830;
+ info->fix.accel = FB_ACCEL_NONE;
info->fix.type_aux = 0;
info->flags = FBINFO_DEFAULT;
info->fbops = &radeonfb_ops;
info->fix.line_length = fb->pitch;
- info->screen_base = fbptr;
- info->fix.smem_start = (unsigned long)fbptr;
+ tmp = fb_gpuaddr - rdev->mc.vram_location;
+ info->fix.smem_start = rdev->mc.aper_base + tmp;
info->fix.smem_len = size;
info->screen_base = fbptr;
info->screen_size = size;
info->var.width = -1;
info->var.xres = fb_width;
info->var.yres = fb_height;
- info->fix.mmio_start = pci_resource_start(rdev->pdev, 2);
- info->fix.mmio_len = pci_resource_len(rdev->pdev, 2);
+ info->fix.mmio_start = 0;
+ info->fix.mmio_len = 0;
info->pixmap.size = 64*1024;
info->pixmap.buf_align = 8;
info->pixmap.access_align = 32;
if (robj) {
radeon_object_kunmap(robj);
}
- if (ret) {
+ if (fb && ret) {
list_del(&fb->filp_head);
drm_gem_object_unreference(gobj);
drm_framebuffer_cleanup(fb);
robj = rfb->obj->driver_private;
unregister_framebuffer(info);
radeon_object_kunmap(robj);
+ radeon_object_unpin(robj);
framebuffer_release(info);
}
{
uint32_t flags;
uint32_t tmp;
- void *fbptr;
int r;
flags = radeon_object_flags_from_domain(domain);
DRM_ERROR("radeon: failed to reserve object for pinning it.\n");
return r;
}
- if (robj->rdev->fbdev_robj == robj) {
- mutex_lock(&robj->rdev->fbdev_info->lock);
- radeon_object_kunmap(robj);
- }
tmp = robj->tobj.mem.placement;
ttm_flag_masked(&tmp, flags, TTM_PL_MASK_MEM);
robj->tobj.proposed_placement = tmp | TTM_PL_FLAG_NO_EVICT | TTM_PL_MASK_CACHING;
DRM_ERROR("radeon: failed to pin object.\n");
}
radeon_object_unreserve(robj);
- if (robj->rdev->fbdev_robj == robj) {
- if (!r) {
- r = radeon_object_kmap(robj, &fbptr);
- }
- if (!r) {
- robj->rdev->fbdev_info->screen_base = fbptr;
- robj->rdev->fbdev_info->fix.smem_start = (unsigned long)fbptr;
- }
- mutex_unlock(&robj->rdev->fbdev_info->lock);
- }
return r;
}
void radeon_object_unpin(struct radeon_object *robj)
{
uint32_t flags;
- void *fbptr;
int r;
spin_lock(&robj->tobj.lock);
DRM_ERROR("radeon: failed to reserve object for unpinning it.\n");
return;
}
- if (robj->rdev->fbdev_robj == robj) {
- mutex_lock(&robj->rdev->fbdev_info->lock);
- radeon_object_kunmap(robj);
- }
flags = robj->tobj.mem.placement;
robj->tobj.proposed_placement = flags & ~TTM_PL_FLAG_NO_EVICT;
r = ttm_buffer_object_validate(&robj->tobj,
DRM_ERROR("radeon: failed to unpin buffer.\n");
}
radeon_object_unreserve(robj);
- if (robj->rdev->fbdev_robj == robj) {
- if (!r) {
- r = radeon_object_kmap(robj, &fbptr);
- }
- if (!r) {
- robj->rdev->fbdev_info->screen_base = fbptr;
- robj->rdev->fbdev_info->fix.smem_start = (unsigned long)fbptr;
- }
- mutex_unlock(&robj->rdev->fbdev_info->lock);
- }
}
int radeon_object_wait(struct radeon_object *robj)
#include <linux/highmem.h>
#include <linux/wait.h>
#include <linux/vmalloc.h>
-#include <linux/version.h>
#include <linux/module.h>
void ttm_bo_free_old_node(struct ttm_buffer_object *bo)
#include <ttm/ttm_bo_driver.h>
#include <ttm/ttm_placement.h>
#include <linux/mm.h>
-#include <linux/version.h>
#include <linux/rbtree.h>
#include <linux/module.h>
#include <linux/uaccess.h>
* Authors: Thomas Hellstrom <thellstrom-at-vmware-dot-com>
*/
-#include <linux/version.h>
#include <linux/vmalloc.h>
#include <linux/sched.h>
#include <linux/highmem.h>
config I2C_DESIGNWARE
tristate "Synopsys DesignWare"
+ depends on HAVE_CLK
help
If you say yes to this option, support will be included for the
Synopsys DesignWare I2C adapter. Only master mode is supported.
ide_pci_setup_ports(dev, d, &hw[0], &hws[0]);
hw[0].irq = 14;
+ hw[1].irq = 15;
return ide_host_add(d, hws, 2, NULL);
}
return stat;
/*
- * Sanity check the given block size
+ * Sanity check the given block size, in so far as making
+ * sure the sectors_per_frame we give to the caller won't
+ * end up being bogus.
*/
blocklen = be32_to_cpu(capbuf.blocklen);
+ blocklen = (blocklen >> SECTOR_BITS) << SECTOR_BITS;
switch (blocklen) {
case 512:
case 1024:
case 4096:
break;
default:
- printk(KERN_ERR PFX "%s: weird block size %u\n",
+ printk_once(KERN_ERR PFX "%s: weird block size %u; "
+ "setting default block size to 2048\n",
drive->name, blocklen);
- printk(KERN_ERR PFX "%s: default to 2kb block size\n",
- drive->name);
blocklen = 2048;
break;
}
if (__ide_dma_bad_drive(drive))
return 0;
- if (ide_id_dma_bug(drive))
- return 0;
-
if (hwif->host_flags & IDE_HFLAG_TRUST_BIOS_FOR_DMA)
return config_drive_for_dma(drive);
return -1;
}
-int ide_id_dma_bug(ide_drive_t *drive)
-{
- u16 *id = drive->id;
-
- if (id[ATA_ID_FIELD_VALID] & 4) {
- if ((id[ATA_ID_UDMA_MODES] >> 8) &&
- (id[ATA_ID_MWDMA_MODES] >> 8))
- goto err_out;
- } else if ((id[ATA_ID_MWDMA_MODES] >> 8) &&
- (id[ATA_ID_SWDMA_MODES] >> 8))
- goto err_out;
-
- return 0;
-err_out:
- printk(KERN_ERR "%s: bad DMA info in identify block\n", drive->name);
- return 1;
-}
-
int ide_set_dma(ide_drive_t *drive)
{
int rc;
if (!ide_lock_port(hwif)) {
ide_hwif_t *prev_port;
-
- WARN_ON_ONCE(hwif->rq);
repeat:
prev_port = hwif->host->cur_port;
+
+ if (drive->dev_flags & IDE_DFLAG_BLOCKED)
+ rq = hwif->rq;
+ else
+ WARN_ON_ONCE(hwif->rq);
+
if (drive->dev_flags & IDE_DFLAG_SLEEPING &&
time_after(drive->sleep, jiffies)) {
ide_unlock_port(hwif);
hwif->cur_dev = drive;
drive->dev_flags &= ~(IDE_DFLAG_SLEEPING | IDE_DFLAG_PARKED);
- spin_unlock_irq(&hwif->lock);
- spin_lock_irq(q->queue_lock);
- /*
- * we know that the queue isn't empty, but this can happen
- * if the q->prep_rq_fn() decides to kill a request
- */
- if (!rq)
+ if (rq == NULL) {
+ spin_unlock_irq(&hwif->lock);
+ spin_lock_irq(q->queue_lock);
+ /*
+ * we know that the queue isn't empty, but this can
+ * happen if ->prep_rq_fn() decides to kill a request
+ */
rq = blk_fetch_request(drive->queue);
+ spin_unlock_irq(q->queue_lock);
+ spin_lock_irq(&hwif->lock);
- spin_unlock_irq(q->queue_lock);
- spin_lock_irq(&hwif->lock);
-
- if (!rq) {
- ide_unlock_port(hwif);
- goto out;
+ if (rq == NULL) {
+ ide_unlock_port(hwif);
+ goto out;
+ }
}
/*
* Sanity: don't accept a request that isn't a PM request
- * if we are currently power managed. This is very important as
- * blk_stop_queue() doesn't prevent the blk_fetch_request()
- * above to return us whatever is in the queue. Since we call
- * ide_do_request() ourselves, we end up taking requests while
- * the queue is blocked...
- *
- * We let requests forced at head of queue with ide-preempt
- * though. I hope that doesn't happen too much, hopefully not
- * unless the subdriver triggers such a thing in its own PM
- * state machine.
+ * if we are currently power managed.
*/
- if ((drive->dev_flags & IDE_DFLAG_BLOCKED) &&
- blk_pm_request(rq) == 0 &&
- (rq->cmd_flags & REQ_PREEMPT) == 0) {
- /* there should be no pending command at this point */
- ide_unlock_port(hwif);
- goto plug_device;
- }
+ BUG_ON((drive->dev_flags & IDE_DFLAG_BLOCKED) &&
+ blk_pm_request(rq) == 0);
hwif->rq = rq;
*/
static const struct drive_list_entry ivb_list[] = {
{ "QUANTUM FIREBALLlct10 05" , "A03.0900" },
+ { "QUANTUM FIREBALLlct20 30" , "APL.0900" },
{ "TSSTcorp CDDVDW SH-S202J" , "SB00" },
{ "TSSTcorp CDDVDW SH-S202J" , "SB01" },
{ "TSSTcorp CDDVDW SH-S202N" , "SB00" },
kfree(id);
- if ((drive->dev_flags & IDE_DFLAG_USING_DMA) && ide_id_dma_bug(drive))
- ide_dma_off(drive);
-
return 1;
out_err:
if (rc == 2)
return j;
}
+static void ide_host_enable_irqs(struct ide_host *host)
+{
+ ide_hwif_t *hwif;
+ int i;
+
+ ide_host_for_each_port(i, hwif, host) {
+ if (hwif == NULL)
+ continue;
+
+ /* clear any pending IRQs */
+ hwif->tp_ops->read_status(hwif);
+
+ /* unmask IRQs */
+ if (hwif->io_ports.ctl_addr)
+ hwif->tp_ops->write_devctl(hwif, ATA_DEVCTL_OBS);
+ }
+}
+
/*
* This routine sets up the IRQ for an IDE interface.
*/
if (irq_handler == NULL)
irq_handler = ide_intr;
- if (io_ports->ctl_addr)
- hwif->tp_ops->write_devctl(hwif, ATA_DEVCTL_OBS);
-
if (request_irq(hwif->irq, irq_handler, sa, hwif->name, hwif))
goto out_up;
ide_port_tune_devices(hwif);
}
+ ide_host_enable_irqs(host);
+
ide_host_for_each_port(i, hwif, host) {
if (hwif == NULL)
continue;
depends on LEDS_CLASS && X86 && EXPERIMENTAL
help
This option enables support for the PCEngines ALIX.2 and ALIX.3 LEDs.
+ You have to set leds-alix2.force=1 for boards with Award BIOS.
config LEDS_H1940
tristate "LED Support for iPAQ H1940 device"
of_platform devices. For instance, LEDs which are listed in a "dts"
file.
-config LEDS_LP5521
- tristate "LED Support for the LP5521 LEDs"
+config LEDS_LP3944
+ tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
depends on LEDS_CLASS && I2C
help
- If you say 'Y' here you get support for the National Semiconductor
- LP5521 LED driver used in n8x0 boards.
+ This option enables support for LEDs connected to the National
+ Semiconductor LP3944 Lighting Management Unit (LMU) also known as
+ Fun Light Chip.
- This driver can be built as a module by choosing 'M'. The module
- will be called leds-lp5521.
+ To compile this driver as a module, choose M here: the
+ module will be called leds-lp3944.
config LEDS_CLEVO_MAIL
tristate "Mail LED on Clevo notebook"
obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunfire.o
obj-$(CONFIG_LEDS_PCA9532) += leds-pca9532.o
obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
+obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o
obj-$(CONFIG_LEDS_CLEVO_MAIL) += leds-clevo-mail.o
obj-$(CONFIG_LEDS_HP6XX) += leds-hp6xx.o
obj-$(CONFIG_LEDS_FSG) += leds-fsg.o
static int force = 0;
module_param(force, bool, 0444);
-MODULE_PARM_DESC(force, "Assume system has ALIX.2 style LEDs");
+MODULE_PARM_DESC(force, "Assume system has ALIX.2/ALIX.3 style LEDs");
struct alix_led {
struct led_classdev cdev;
goto out;
}
+ /* enable output on GPIO for LED 1,2,3 */
+ outl(1 << 6, 0x6104);
+ outl(1 << 9, 0x6184);
+ outl(1 << 11, 0x6184);
+
pdev = platform_device_register_simple(KBUILD_MODNAME, -1, NULL, 0);
if (!IS_ERR(pdev)) {
ret = platform_driver_probe(&alix_led_driver, alix_led_probe);
enum led_ids led_id;
enum led_colors color;
enum led_bits state;
+
+ /* General attributes of RGB LEDs */
+ int wave_pattern;
+ int rgb_current;
};
bd2802_reset_cancel(led);
reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT1SETUP);
- bd2802_write_byte(led->client, reg, BD2802_CURRENT_032);
+ bd2802_write_byte(led->client, reg, led->rgb_current);
reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT2SETUP);
bd2802_write_byte(led->client, reg, BD2802_CURRENT_000);
reg = bd2802_get_reg_addr(id, color, BD2802_REG_WAVEPATTERN);
reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT1SETUP);
bd2802_write_byte(led->client, reg, BD2802_CURRENT_000);
reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT2SETUP);
- bd2802_write_byte(led->client, reg, BD2802_CURRENT_032);
+ bd2802_write_byte(led->client, reg, led->rgb_current);
reg = bd2802_get_reg_addr(id, color, BD2802_REG_WAVEPATTERN);
- bd2802_write_byte(led->client, reg, BD2802_PATTERN_HALF);
+ bd2802_write_byte(led->client, reg, led->wave_pattern);
bd2802_enable(led, id);
bd2802_update_state(led, id, color, BD2802_BLINK);
ret = device_create_file(&led->client->dev,
bd2802_addr_attributes[i]);
if (ret) {
- dev_err(&led->client->dev, "failed to sysfs file %s\n",
+ dev_err(&led->client->dev, "failed: sysfs file %s\n",
bd2802_addr_attributes[i]->attr.name);
goto failed_remove_files;
}
.store = bd2802_store_adv_conf,
};
+#define BD2802_CONTROL_ATTR(attr_name, name_str) \
+static ssize_t bd2802_show_##attr_name(struct device *dev, \
+ struct device_attribute *attr, char *buf) \
+{ \
+ struct bd2802_led *led = i2c_get_clientdata(to_i2c_client(dev));\
+ ssize_t ret; \
+ down_read(&led->rwsem); \
+ ret = sprintf(buf, "0x%02x\n", led->attr_name); \
+ up_read(&led->rwsem); \
+ return ret; \
+} \
+static ssize_t bd2802_store_##attr_name(struct device *dev, \
+ struct device_attribute *attr, const char *buf, size_t count) \
+{ \
+ struct bd2802_led *led = i2c_get_clientdata(to_i2c_client(dev));\
+ unsigned long val; \
+ int ret; \
+ if (!count) \
+ return -EINVAL; \
+ ret = strict_strtoul(buf, 16, &val); \
+ if (ret) \
+ return ret; \
+ down_write(&led->rwsem); \
+ led->attr_name = val; \
+ up_write(&led->rwsem); \
+ return count; \
+} \
+static struct device_attribute bd2802_##attr_name##_attr = { \
+ .attr = { \
+ .name = name_str, \
+ .mode = 0644, \
+ .owner = THIS_MODULE \
+ }, \
+ .show = bd2802_show_##attr_name, \
+ .store = bd2802_store_##attr_name, \
+};
+
+BD2802_CONTROL_ATTR(wave_pattern, "wave_pattern");
+BD2802_CONTROL_ATTR(rgb_current, "rgb_current");
+
+static struct device_attribute *bd2802_attributes[] = {
+ &bd2802_adv_conf_attr,
+ &bd2802_wave_pattern_attr,
+ &bd2802_rgb_current_attr,
+};
+
static void bd2802_led_work(struct work_struct *work)
{
struct bd2802_led *led = container_of(work, struct bd2802_led, work);
led->cdev_led1r.brightness = LED_OFF;
led->cdev_led1r.brightness_set = bd2802_set_led1r_brightness;
led->cdev_led1r.blink_set = bd2802_set_led1r_blink;
- led->cdev_led1r.flags |= LED_CORE_SUSPENDRESUME;
ret = led_classdev_register(&led->client->dev, &led->cdev_led1r);
if (ret < 0) {
led->cdev_led1g.brightness = LED_OFF;
led->cdev_led1g.brightness_set = bd2802_set_led1g_brightness;
led->cdev_led1g.blink_set = bd2802_set_led1g_blink;
- led->cdev_led1g.flags |= LED_CORE_SUSPENDRESUME;
ret = led_classdev_register(&led->client->dev, &led->cdev_led1g);
if (ret < 0) {
led->cdev_led1b.brightness = LED_OFF;
led->cdev_led1b.brightness_set = bd2802_set_led1b_brightness;
led->cdev_led1b.blink_set = bd2802_set_led1b_blink;
- led->cdev_led1b.flags |= LED_CORE_SUSPENDRESUME;
ret = led_classdev_register(&led->client->dev, &led->cdev_led1b);
if (ret < 0) {
led->cdev_led2r.brightness = LED_OFF;
led->cdev_led2r.brightness_set = bd2802_set_led2r_brightness;
led->cdev_led2r.blink_set = bd2802_set_led2r_blink;
- led->cdev_led2r.flags |= LED_CORE_SUSPENDRESUME;
ret = led_classdev_register(&led->client->dev, &led->cdev_led2r);
if (ret < 0) {
led->cdev_led2g.brightness = LED_OFF;
led->cdev_led2g.brightness_set = bd2802_set_led2g_brightness;
led->cdev_led2g.blink_set = bd2802_set_led2g_blink;
- led->cdev_led2g.flags |= LED_CORE_SUSPENDRESUME;
ret = led_classdev_register(&led->client->dev, &led->cdev_led2g);
if (ret < 0) {
{
struct bd2802_led *led;
struct bd2802_led_platform_data *pdata;
- int ret;
+ int ret, i;
led = kzalloc(sizeof(struct bd2802_led), GFP_KERNEL);
if (!led) {
/* To save the power, reset BD2802 after detecting */
gpio_set_value(led->pdata->reset_gpio, 0);
+ /* Default attributes */
+ led->wave_pattern = BD2802_PATTERN_HALF;
+ led->rgb_current = BD2802_CURRENT_032;
+
init_rwsem(&led->rwsem);
- ret = device_create_file(&client->dev, &bd2802_adv_conf_attr);
- if (ret) {
- dev_err(&client->dev, "failed to create sysfs file %s\n",
- bd2802_adv_conf_attr.attr.name);
- goto failed_free;
+ for (i = 0; i < ARRAY_SIZE(bd2802_attributes); i++) {
+ ret = device_create_file(&led->client->dev,
+ bd2802_attributes[i]);
+ if (ret) {
+ dev_err(&led->client->dev, "failed: sysfs file %s\n",
+ bd2802_attributes[i]->attr.name);
+ goto failed_unregister_dev_file;
+ }
}
ret = bd2802_register_led_classdev(led);
return 0;
failed_unregister_dev_file:
- device_remove_file(&client->dev, &bd2802_adv_conf_attr);
+ for (i--; i >= 0; i--)
+ device_remove_file(&led->client->dev, bd2802_attributes[i]);
failed_free:
i2c_set_clientdata(client, NULL);
kfree(led);
static int __exit bd2802_remove(struct i2c_client *client)
{
struct bd2802_led *led = i2c_get_clientdata(client);
+ int i;
- bd2802_unregister_led_classdev(led);
gpio_set_value(led->pdata->reset_gpio, 0);
+ bd2802_unregister_led_classdev(led);
if (led->adf_on)
bd2802_disable_adv_conf(led);
- device_remove_file(&client->dev, &bd2802_adv_conf_attr);
+ for (i = 0; i < ARRAY_SIZE(bd2802_attributes); i++)
+ device_remove_file(&led->client->dev, bd2802_attributes[i]);
i2c_set_clientdata(client, NULL);
kfree(led);
struct bd2802_led *led = i2c_get_clientdata(client);
if (!bd2802_is_all_off(led) || led->adf_on) {
- gpio_set_value(led->pdata->reset_gpio, 1);
- udelay(100);
+ bd2802_reset_cancel(led);
bd2802_restore_state(led);
}
MODULE_AUTHOR("Kim Kyuwon <q1.kim@samsung.com>");
MODULE_DESCRIPTION("BD2802 LED driver");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
struct gpio_led_data *led_dat, struct device *parent,
int (*blink_set)(unsigned, unsigned long *, unsigned long *))
{
- int ret;
+ int ret, state;
/* skip leds that aren't available */
if (!gpio_is_valid(template->gpio)) {
led_dat->cdev.blink_set = gpio_blink_set;
}
led_dat->cdev.brightness_set = gpio_led_set;
- led_dat->cdev.brightness = LED_OFF;
+ if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP)
+ state = !!gpio_get_value(led_dat->gpio) ^ led_dat->active_low;
+ else
+ state = (template->default_state == LEDS_GPIO_DEFSTATE_ON);
+ led_dat->cdev.brightness = state ? LED_FULL : LED_OFF;
if (!template->retain_state_suspended)
led_dat->cdev.flags |= LED_CORE_SUSPENDRESUME;
- ret = gpio_direction_output(led_dat->gpio, led_dat->active_low);
+ ret = gpio_direction_output(led_dat->gpio, led_dat->active_low ^ state);
if (ret < 0)
goto err;
}
#ifdef CONFIG_LEDS_GPIO_PLATFORM
-static int gpio_led_probe(struct platform_device *pdev)
+static int __devinit gpio_led_probe(struct platform_device *pdev)
{
struct gpio_led_platform_data *pdata = pdev->dev.platform_data;
struct gpio_led_data *leds_data;
memset(&led, 0, sizeof(led));
for_each_child_of_node(np, child) {
enum of_gpio_flags flags;
+ const char *state;
led.gpio = of_get_gpio_flags(child, 0, &flags);
led.active_low = flags & OF_GPIO_ACTIVE_LOW;
led.name = of_get_property(child, "label", NULL) ? : child->name;
led.default_trigger =
of_get_property(child, "linux,default-trigger", NULL);
+ state = of_get_property(child, "default-state", NULL);
+ if (state) {
+ if (!strcmp(state, "keep"))
+ led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ else if(!strcmp(state, "on"))
+ led.default_state = LEDS_GPIO_DEFSTATE_ON;
+ else
+ led.default_state = LEDS_GPIO_DEFSTATE_OFF;
+ }
ret = create_gpio_led(&led, &pdata->led_data[pdata->num_leds++],
&ofdev->dev, NULL);
--- /dev/null
+/*
+ * leds-lp3944.c - driver for National Semiconductor LP3944 Funlight Chip
+ *
+ * Copyright (C) 2009 Antonio Ospite <ospite@studenti.unina.it>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+/*
+ * I2C driver for National Semiconductor LP3944 Funlight Chip
+ * http://www.national.com/pf/LP/LP3944.html
+ *
+ * This helper chip can drive up to 8 leds, with two programmable DIM modes;
+ * it could even be used as a gpio expander but this driver assumes it is used
+ * as a led controller.
+ *
+ * The DIM modes are used to set _blink_ patterns for leds, the pattern is
+ * specified supplying two parameters:
+ * - period: from 0s to 1.6s
+ * - duty cycle: percentage of the period the led is on, from 0 to 100
+ *
+ * LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
+ * leds, the camera flash light and the displays backlights.
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/mutex.h>
+#include <linux/workqueue.h>
+#include <linux/leds-lp3944.h>
+
+/* Read Only Registers */
+#define LP3944_REG_INPUT1 0x00 /* LEDs 0-7 InputRegister (Read Only) */
+#define LP3944_REG_REGISTER1 0x01 /* None (Read Only) */
+
+#define LP3944_REG_PSC0 0x02 /* Frequency Prescaler 0 (R/W) */
+#define LP3944_REG_PWM0 0x03 /* PWM Register 0 (R/W) */
+#define LP3944_REG_PSC1 0x04 /* Frequency Prescaler 1 (R/W) */
+#define LP3944_REG_PWM1 0x05 /* PWM Register 1 (R/W) */
+#define LP3944_REG_LS0 0x06 /* LEDs 0-3 Selector (R/W) */
+#define LP3944_REG_LS1 0x07 /* LEDs 4-7 Selector (R/W) */
+
+/* These registers are not used to control leds in LP3944, they can store
+ * arbitrary values which the chip will ignore.
+ */
+#define LP3944_REG_REGISTER8 0x08
+#define LP3944_REG_REGISTER9 0x09
+
+#define LP3944_DIM0 0
+#define LP3944_DIM1 1
+
+/* period in ms */
+#define LP3944_PERIOD_MIN 0
+#define LP3944_PERIOD_MAX 1600
+
+/* duty cycle is a percentage */
+#define LP3944_DUTY_CYCLE_MIN 0
+#define LP3944_DUTY_CYCLE_MAX 100
+
+#define ldev_to_led(c) container_of(c, struct lp3944_led_data, ldev)
+
+/* Saved data */
+struct lp3944_led_data {
+ u8 id;
+ enum lp3944_type type;
+ enum lp3944_status status;
+ struct led_classdev ldev;
+ struct i2c_client *client;
+ struct work_struct work;
+};
+
+struct lp3944_data {
+ struct mutex lock;
+ struct i2c_client *client;
+ struct lp3944_led_data leds[LP3944_LEDS_MAX];
+};
+
+static int lp3944_reg_read(struct i2c_client *client, u8 reg, u8 *value)
+{
+ int tmp;
+
+ tmp = i2c_smbus_read_byte_data(client, reg);
+ if (tmp < 0)
+ return -EINVAL;
+
+ *value = tmp;
+
+ return 0;
+}
+
+static int lp3944_reg_write(struct i2c_client *client, u8 reg, u8 value)
+{
+ return i2c_smbus_write_byte_data(client, reg, value);
+}
+
+/**
+ * Set the period for DIM status
+ *
+ * @client: the i2c client
+ * @dim: either LP3944_DIM0 or LP3944_DIM1
+ * @period: period of a blink, that is a on/off cycle, expressed in ms.
+ */
+static int lp3944_dim_set_period(struct i2c_client *client, u8 dim, u16 period)
+{
+ u8 psc_reg;
+ u8 psc_value;
+ int err;
+
+ if (dim == LP3944_DIM0)
+ psc_reg = LP3944_REG_PSC0;
+ else if (dim == LP3944_DIM1)
+ psc_reg = LP3944_REG_PSC1;
+ else
+ return -EINVAL;
+
+ /* Convert period to Prescaler value */
+ if (period > LP3944_PERIOD_MAX)
+ return -EINVAL;
+
+ psc_value = (period * 255) / LP3944_PERIOD_MAX;
+
+ err = lp3944_reg_write(client, psc_reg, psc_value);
+
+ return err;
+}
+
+/**
+ * Set the duty cycle for DIM status
+ *
+ * @client: the i2c client
+ * @dim: either LP3944_DIM0 or LP3944_DIM1
+ * @duty_cycle: percentage of a period during which a led is ON
+ */
+static int lp3944_dim_set_dutycycle(struct i2c_client *client, u8 dim,
+ u8 duty_cycle)
+{
+ u8 pwm_reg;
+ u8 pwm_value;
+ int err;
+
+ if (dim == LP3944_DIM0)
+ pwm_reg = LP3944_REG_PWM0;
+ else if (dim == LP3944_DIM1)
+ pwm_reg = LP3944_REG_PWM1;
+ else
+ return -EINVAL;
+
+ /* Convert duty cycle to PWM value */
+ if (duty_cycle > LP3944_DUTY_CYCLE_MAX)
+ return -EINVAL;
+
+ pwm_value = (duty_cycle * 255) / LP3944_DUTY_CYCLE_MAX;
+
+ err = lp3944_reg_write(client, pwm_reg, pwm_value);
+
+ return err;
+}
+
+/**
+ * Set the led status
+ *
+ * @led: a lp3944_led_data structure
+ * @status: one of LP3944_LED_STATUS_OFF
+ * LP3944_LED_STATUS_ON
+ * LP3944_LED_STATUS_DIM0
+ * LP3944_LED_STATUS_DIM1
+ */
+static int lp3944_led_set(struct lp3944_led_data *led, u8 status)
+{
+ struct lp3944_data *data = i2c_get_clientdata(led->client);
+ u8 id = led->id;
+ u8 reg;
+ u8 val = 0;
+ int err;
+
+ dev_dbg(&led->client->dev, "%s: %s, status before normalization:%d\n",
+ __func__, led->ldev.name, status);
+
+ switch (id) {
+ case LP3944_LED0:
+ case LP3944_LED1:
+ case LP3944_LED2:
+ case LP3944_LED3:
+ reg = LP3944_REG_LS0;
+ break;
+ case LP3944_LED4:
+ case LP3944_LED5:
+ case LP3944_LED6:
+ case LP3944_LED7:
+ id -= LP3944_LED4;
+ reg = LP3944_REG_LS1;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (status > LP3944_LED_STATUS_DIM1)
+ return -EINVAL;
+
+ /* invert only 0 and 1, leave unchanged the other values,
+ * remember we are abusing status to set blink patterns
+ */
+ if (led->type == LP3944_LED_TYPE_LED_INVERTED && status < 2)
+ status = 1 - status;
+
+ mutex_lock(&data->lock);
+ lp3944_reg_read(led->client, reg, &val);
+
+ val &= ~(LP3944_LED_STATUS_MASK << (id << 1));
+ val |= (status << (id << 1));
+
+ dev_dbg(&led->client->dev, "%s: %s, reg:%d id:%d status:%d val:%#x\n",
+ __func__, led->ldev.name, reg, id, status, val);
+
+ /* set led status */
+ err = lp3944_reg_write(led->client, reg, val);
+ mutex_unlock(&data->lock);
+
+ return err;
+}
+
+static int lp3944_led_set_blink(struct led_classdev *led_cdev,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ struct lp3944_led_data *led = ldev_to_led(led_cdev);
+ u16 period;
+ u8 duty_cycle;
+ int err;
+
+ /* units are in ms */
+ if (*delay_on + *delay_off > LP3944_PERIOD_MAX)
+ return -EINVAL;
+
+ if (*delay_on == 0 && *delay_off == 0) {
+ /* Special case: the leds subsystem requires a default user
+ * friendly blink pattern for the LED. Let's blink the led
+ * slowly (1Hz).
+ */
+ *delay_on = 500;
+ *delay_off = 500;
+ }
+
+ period = (*delay_on) + (*delay_off);
+
+ /* duty_cycle is the percentage of period during which the led is ON */
+ duty_cycle = 100 * (*delay_on) / period;
+
+ /* invert duty cycle for inverted leds, this has the same effect of
+ * swapping delay_on and delay_off
+ */
+ if (led->type == LP3944_LED_TYPE_LED_INVERTED)
+ duty_cycle = 100 - duty_cycle;
+
+ /* NOTE: using always the first DIM mode, this means that all leds
+ * will have the same blinking pattern.
+ *
+ * We could find a way later to have two leds blinking in hardware
+ * with different patterns at the same time, falling back to software
+ * control for the other ones.
+ */
+ err = lp3944_dim_set_period(led->client, LP3944_DIM0, period);
+ if (err)
+ return err;
+
+ err = lp3944_dim_set_dutycycle(led->client, LP3944_DIM0, duty_cycle);
+ if (err)
+ return err;
+
+ dev_dbg(&led->client->dev, "%s: OK hardware accelerated blink!\n",
+ __func__);
+
+ led->status = LP3944_LED_STATUS_DIM0;
+ schedule_work(&led->work);
+
+ return 0;
+}
+
+static void lp3944_led_set_brightness(struct led_classdev *led_cdev,
+ enum led_brightness brightness)
+{
+ struct lp3944_led_data *led = ldev_to_led(led_cdev);
+
+ dev_dbg(&led->client->dev, "%s: %s, %d\n",
+ __func__, led_cdev->name, brightness);
+
+ led->status = brightness;
+ schedule_work(&led->work);
+}
+
+static void lp3944_led_work(struct work_struct *work)
+{
+ struct lp3944_led_data *led;
+
+ led = container_of(work, struct lp3944_led_data, work);
+ lp3944_led_set(led, led->status);
+}
+
+static int lp3944_configure(struct i2c_client *client,
+ struct lp3944_data *data,
+ struct lp3944_platform_data *pdata)
+{
+ int i, err = 0;
+
+ for (i = 0; i < pdata->leds_size; i++) {
+ struct lp3944_led *pled = &pdata->leds[i];
+ struct lp3944_led_data *led = &data->leds[i];
+ led->client = client;
+ led->id = i;
+
+ switch (pled->type) {
+
+ case LP3944_LED_TYPE_LED:
+ case LP3944_LED_TYPE_LED_INVERTED:
+ led->type = pled->type;
+ led->status = pled->status;
+ led->ldev.name = pled->name;
+ led->ldev.max_brightness = 1;
+ led->ldev.brightness_set = lp3944_led_set_brightness;
+ led->ldev.blink_set = lp3944_led_set_blink;
+ led->ldev.flags = LED_CORE_SUSPENDRESUME;
+
+ INIT_WORK(&led->work, lp3944_led_work);
+ err = led_classdev_register(&client->dev, &led->ldev);
+ if (err < 0) {
+ dev_err(&client->dev,
+ "couldn't register LED %s\n",
+ led->ldev.name);
+ goto exit;
+ }
+
+ /* to expose the default value to userspace */
+ led->ldev.brightness = led->status;
+
+ /* Set the default led status */
+ err = lp3944_led_set(led, led->status);
+ if (err < 0) {
+ dev_err(&client->dev,
+ "%s couldn't set STATUS %d\n",
+ led->ldev.name, led->status);
+ goto exit;
+ }
+ break;
+
+ case LP3944_LED_TYPE_NONE:
+ default:
+ break;
+
+ }
+ }
+ return 0;
+
+exit:
+ if (i > 0)
+ for (i = i - 1; i >= 0; i--)
+ switch (pdata->leds[i].type) {
+
+ case LP3944_LED_TYPE_LED:
+ case LP3944_LED_TYPE_LED_INVERTED:
+ led_classdev_unregister(&data->leds[i].ldev);
+ cancel_work_sync(&data->leds[i].work);
+ break;
+
+ case LP3944_LED_TYPE_NONE:
+ default:
+ break;
+ }
+
+ return err;
+}
+
+static int __devinit lp3944_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct lp3944_platform_data *lp3944_pdata = client->dev.platform_data;
+ struct lp3944_data *data;
+
+ if (lp3944_pdata == NULL) {
+ dev_err(&client->dev, "no platform data\n");
+ return -EINVAL;
+ }
+
+ /* Let's see whether this adapter can support what we need. */
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA)) {
+ dev_err(&client->dev, "insufficient functionality!\n");
+ return -ENODEV;
+ }
+
+ data = kzalloc(sizeof(struct lp3944_data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->client = client;
+ i2c_set_clientdata(client, data);
+
+ mutex_init(&data->lock);
+
+ dev_info(&client->dev, "lp3944 enabled\n");
+
+ lp3944_configure(client, data, lp3944_pdata);
+ return 0;
+}
+
+static int __devexit lp3944_remove(struct i2c_client *client)
+{
+ struct lp3944_platform_data *pdata = client->dev.platform_data;
+ struct lp3944_data *data = i2c_get_clientdata(client);
+ int i;
+
+ for (i = 0; i < pdata->leds_size; i++)
+ switch (data->leds[i].type) {
+ case LP3944_LED_TYPE_LED:
+ case LP3944_LED_TYPE_LED_INVERTED:
+ led_classdev_unregister(&data->leds[i].ldev);
+ cancel_work_sync(&data->leds[i].work);
+ break;
+
+ case LP3944_LED_TYPE_NONE:
+ default:
+ break;
+ }
+
+ kfree(data);
+ i2c_set_clientdata(client, NULL);
+
+ return 0;
+}
+
+/* lp3944 i2c driver struct */
+static const struct i2c_device_id lp3944_id[] = {
+ {"lp3944", 0},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, lp3944_id);
+
+static struct i2c_driver lp3944_driver = {
+ .driver = {
+ .name = "lp3944",
+ },
+ .probe = lp3944_probe,
+ .remove = __devexit_p(lp3944_remove),
+ .id_table = lp3944_id,
+};
+
+static int __init lp3944_module_init(void)
+{
+ return i2c_add_driver(&lp3944_driver);
+}
+
+static void __exit lp3944_module_exit(void)
+{
+ i2c_del_driver(&lp3944_driver);
+}
+
+module_init(lp3944_module_init);
+module_exit(lp3944_module_exit);
+
+MODULE_AUTHOR("Antonio Ospite <ospite@studenti.unina.it>");
+MODULE_DESCRIPTION("LP3944 Fun Light Chip");
+MODULE_LICENSE("GPL");
struct pca9532_led leds[16];
struct mutex update_lock;
struct input_dev *idev;
- struct work_struct work;
+ struct work_struct work;
u8 pwm[2];
u8 psc[2];
};
if (b > 0xFF)
return -EINVAL;
data->pwm[pwm] = b;
- data->psc[pwm] = blink;
- return 0;
+ data->psc[pwm] = blink;
+ return 0;
}
static int pca9532_setpwm(struct i2c_client *client, int pwm)
{
- struct pca9532_data *data = i2c_get_clientdata(client);
- mutex_lock(&data->update_lock);
+ struct pca9532_data *data = i2c_get_clientdata(client);
+ mutex_lock(&data->update_lock);
i2c_smbus_write_byte_data(client, PCA9532_REG_PWM(pwm),
data->pwm[pwm]);
i2c_smbus_write_byte_data(client, PCA9532_REG_PSC(pwm),
led->state = PCA9532_ON;
else {
led->state = PCA9532_PWM0; /* Thecus: hardcode one pwm */
- err = pca9532_calcpwm(led->client, 0, 0, value);
+ err = pca9532_calcpwm(led->client, 0, 0, value);
if (err)
return; /* XXX: led api doesn't allow error code? */
}
- schedule_work(&led->work);
+ schedule_work(&led->work);
}
static int pca9532_set_blink(struct led_classdev *led_cdev,
struct pca9532_led *led = ldev_to_led(led_cdev);
struct i2c_client *client = led->client;
int psc;
- int err = 0;
+ int err = 0;
if (*delay_on == 0 && *delay_off == 0) {
/* led subsystem ask us for a blink rate */
/* Thecus specific: only use PSC/PWM 0 */
psc = (*delay_on * 152-1)/1000;
- err = pca9532_calcpwm(client, 0, psc, led_cdev->brightness);
- if (err)
- return err;
- schedule_work(&led->work);
- return 0;
+ err = pca9532_calcpwm(client, 0, psc, led_cdev->brightness);
+ if (err)
+ return err;
+ schedule_work(&led->work);
+ return 0;
}
static int pca9532_event(struct input_dev *dev, unsigned int type,
else
data->pwm[1] = 0;
- schedule_work(&data->work);
+ schedule_work(&data->work);
- return 0;
+ return 0;
}
static void pca9532_input_work(struct work_struct *work)
{
- struct pca9532_data *data;
- data = container_of(work, struct pca9532_data, work);
+ struct pca9532_data *data;
+ data = container_of(work, struct pca9532_data, work);
mutex_lock(&data->update_lock);
i2c_smbus_write_byte_data(data->client, PCA9532_REG_PWM(1),
data->pwm[1]);
static void pca9532_led_work(struct work_struct *work)
{
- struct pca9532_led *led;
- led = container_of(work, struct pca9532_led, work);
- if (led->state == PCA9532_PWM0)
- pca9532_setpwm(led->client, 0);
- pca9532_setled(led);
+ struct pca9532_led *led;
+ led = container_of(work, struct pca9532_led, work);
+ if (led->state == PCA9532_PWM0)
+ pca9532_setpwm(led->client, 0);
+ pca9532_setled(led);
}
static int pca9532_configure(struct i2c_client *client,
led->ldev.brightness = LED_OFF;
led->ldev.brightness_set = pca9532_set_brightness;
led->ldev.blink_set = pca9532_set_blink;
- INIT_WORK(&led->work, pca9532_led_work);
+ INIT_WORK(&led->work, pca9532_led_work);
err = led_classdev_register(&client->dev, &led->ldev);
if (err < 0) {
dev_err(&client->dev,
BIT_MASK(SND_TONE);
data->idev->event = pca9532_event;
input_set_drvdata(data->idev, data);
- INIT_WORK(&data->work, pca9532_input_work);
+ INIT_WORK(&data->work, pca9532_input_work);
err = input_register_device(data->idev);
if (err) {
input_free_device(data->idev);
- cancel_work_sync(&data->work);
+ cancel_work_sync(&data->work);
data->idev = NULL;
goto exit;
}
break;
case PCA9532_TYPE_LED:
led_classdev_unregister(&data->leds[i].ldev);
- cancel_work_sync(&data->leds[i].work);
+ cancel_work_sync(&data->leds[i].work);
break;
case PCA9532_TYPE_N2100_BEEP:
if (data->idev != NULL) {
input_unregister_device(data->idev);
input_free_device(data->idev);
- cancel_work_sync(&data->work);
+ cancel_work_sync(&data->work);
data->idev = NULL;
}
break;
break;
case PCA9532_TYPE_LED:
led_classdev_unregister(&data->leds[i].ldev);
- cancel_work_sync(&data->leds[i].work);
+ cancel_work_sync(&data->leds[i].work);
break;
case PCA9532_TYPE_N2100_BEEP:
if (data->idev != NULL) {
input_unregister_device(data->idev);
input_free_device(data->idev);
- cancel_work_sync(&data->work);
+ cancel_work_sync(&data->work);
data->idev = NULL;
}
break;
dev->ofdev.dev.bus = &macio_bus_type;
dev->ofdev.dev.release = macio_release_dev;
+#ifdef CONFIG_PCI
+ /* Set the DMA ops to the ones from the PCI device, this could be
+ * fishy if we didn't know that on PowerMac it's always direct ops
+ * or iommu ops that will work fine
+ */
+ dev->ofdev.dev.archdata.dma_ops =
+ chip->lbus.pdev->dev.archdata.dma_ops;
+ dev->ofdev.dev.archdata.dma_data =
+ chip->lbus.pdev->dev.archdata.dma_data;
+#endif /* CONFIG_PCI */
+
#ifdef DEBUG
printk("preparing mdev @%p, ofdev @%p, dev @%p, kobj @%p\n",
dev, &dev->ofdev, &dev->ofdev.dev, &dev->ofdev.dev.kobj);
if (wol->wolopts & WAKE_PHY)
adapter->wol |= AT_WUFC_LNKC;
+ device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+
return 0;
}
if (wol->wolopts & WAKE_PHY)
adapter->wol |= AT_WUFC_LNKC;
+ device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+
return 0;
}
#define RX_FRAGS_REFILL_WM (RX_Q_LEN - MAX_RX_POST)
#define BE_MAX_LRO_DESCRIPTORS 16
-#define BE_MAX_FRAGS_PER_FRAME 16
+#define BE_MAX_FRAGS_PER_FRAME (min((u32) 16, (u32) MAX_SKB_FRAGS))
struct be_dma_mem {
void *va;
return -EINVAL;
adapter->max_rx_coal = coalesce->rx_max_coalesced_frames;
- if (adapter->max_rx_coal > MAX_SKB_FRAGS)
- adapter->max_rx_coal = MAX_SKB_FRAGS - 1;
+ if (adapter->max_rx_coal > BE_MAX_FRAGS_PER_FRAME)
+ adapter->max_rx_coal = BE_MAX_FRAGS_PER_FRAME;
/* if AIC is being turned on now, start with an EQD of 0 */
if (rx_eq->enable_aic == 0 &&
{
struct be_queue_info *rxq = &adapter->rx_obj.q;
struct be_rx_page_info *page_info;
- u16 rxq_idx, i, num_rcvd;
+ u16 rxq_idx, i, num_rcvd, j;
u32 pktsize, hdr_len, curr_frag_len;
u8 *start;
/* More frags present for this completion */
pktsize -= curr_frag_len; /* account for above copied frag */
- for (i = 1; i < num_rcvd; i++) {
+ for (i = 1, j = 0; i < num_rcvd; i++) {
index_inc(&rxq_idx, rxq->len);
page_info = get_rx_page_info(adapter, rxq_idx);
curr_frag_len = min(pktsize, rx_frag_size);
- skb_shinfo(skb)->frags[i].page = page_info->page;
- skb_shinfo(skb)->frags[i].page_offset = page_info->page_offset;
- skb_shinfo(skb)->frags[i].size = curr_frag_len;
+ /* Coalesce all frags from the same physical page in one slot */
+ if (page_info->page_offset == 0) {
+ /* Fresh page */
+ j++;
+ skb_shinfo(skb)->frags[j].page = page_info->page;
+ skb_shinfo(skb)->frags[j].page_offset =
+ page_info->page_offset;
+ skb_shinfo(skb)->frags[j].size = 0;
+ skb_shinfo(skb)->nr_frags++;
+ } else {
+ put_page(page_info->page);
+ }
+
+ skb_shinfo(skb)->frags[j].size += curr_frag_len;
skb->len += curr_frag_len;
skb->data_len += curr_frag_len;
- skb_shinfo(skb)->nr_frags++;
pktsize -= curr_frag_len;
memset(page_info, 0, sizeof(*page_info));
}
+ BUG_ON(j > MAX_SKB_FRAGS);
done:
be_rx_stats_update(adapter, pktsize, num_rcvd);
struct skb_frag_struct rx_frags[BE_MAX_FRAGS_PER_FRAME];
struct be_queue_info *rxq = &adapter->rx_obj.q;
u32 num_rcvd, pkt_size, remaining, vlanf, curr_frag_len;
- u16 i, rxq_idx = 0, vid;
+ u16 i, rxq_idx = 0, vid, j;
num_rcvd = AMAP_GET_BITS(struct amap_eth_rx_compl, numfrags, rxcp);
pkt_size = AMAP_GET_BITS(struct amap_eth_rx_compl, pktsize, rxcp);
rxq_idx = AMAP_GET_BITS(struct amap_eth_rx_compl, fragndx, rxcp);
remaining = pkt_size;
- for (i = 0; i < num_rcvd; i++) {
+ for (i = 0, j = -1; i < num_rcvd; i++) {
page_info = get_rx_page_info(adapter, rxq_idx);
curr_frag_len = min(remaining, rx_frag_size);
- rx_frags[i].page = page_info->page;
- rx_frags[i].page_offset = page_info->page_offset;
- rx_frags[i].size = curr_frag_len;
- remaining -= curr_frag_len;
+ /* Coalesce all frags from the same physical page in one slot */
+ if (i == 0 || page_info->page_offset == 0) {
+ /* First frag or Fresh page */
+ j++;
+ rx_frags[j].page = page_info->page;
+ rx_frags[j].page_offset = page_info->page_offset;
+ rx_frags[j].size = 0;
+ } else {
+ put_page(page_info->page);
+ }
+ rx_frags[j].size += curr_frag_len;
+ remaining -= curr_frag_len;
index_inc(&rxq_idx, rxq->len);
-
memset(page_info, 0, sizeof(*page_info));
}
+ BUG_ON(j > MAX_SKB_FRAGS);
if (likely(!vlanf)) {
lro_receive_frags(&adapter->rx_obj.lro_mgr, rx_frags, pkt_size,
.ndo_start_xmit = cpmac_start_xmit,
.ndo_tx_timeout = cpmac_tx_timeout,
.ndo_set_multicast_list = cpmac_set_multicast_list,
- .ndo_so_ioctl = cpmac_ioctl,
+ .ndo_do_ioctl = cpmac_ioctl,
.ndo_set_config = cpmac_config,
.ndo_change_mtu = eth_change_mtu,
.ndo_validate_addr = eth_validate_addr,
}
-#ifdef CONFIG_GIANFAR
+#if defined(CONFIG_GIANFAR) || defined(CONFIG_GIANFAR_MODULE)
static u32 __iomem *get_gfar_tbipa(struct fsl_pq_mdio __iomem *regs)
{
struct gfar __iomem *enet_regs;
#endif
-#ifdef CONFIG_UCC_GETH
+#if defined(CONFIG_UCC_GETH) || defined(CONFIG_UCC_GETH_MODULE)
static int get_ucc_id_for_range(u64 start, u64 end, u32 *ucc_id)
{
struct device_node *np = NULL;
if (of_device_is_compatible(np, "fsl,gianfar-mdio") ||
of_device_is_compatible(np, "fsl,gianfar-tbi") ||
of_device_is_compatible(np, "gianfar")) {
-#ifdef CONFIG_GIANFAR
+#if defined(CONFIG_GIANFAR) || defined(CONFIG_GIANFAR_MODULE)
tbipa = get_gfar_tbipa(regs);
#else
err = -ENODEV;
#endif
} else if (of_device_is_compatible(np, "fsl,ucc-mdio") ||
of_device_is_compatible(np, "ucc_geth_phy")) {
-#ifdef CONFIG_UCC_GETH
+#if defined(CONFIG_UCC_GETH) || defined(CONFIG_UCC_GETH_MODULE)
u32 id;
static u32 mii_mng_master;
#include <linux/mdio.h>
#include <linux/module.h>
+MODULE_DESCRIPTION("Generic support for MDIO-compatible transceivers");
+MODULE_AUTHOR("Copyright 2006-2009 Solarflare Communications Inc.");
+MODULE_LICENSE("GPL");
+
/**
* mdio45_probe - probe for an MDIO (clause 45) device
* @mdio: MDIO interface
struct sh_eth_private *mdp = netdev_priv(ndev);
struct sh_eth_cpu_data *cd = mdp->cd;
irqreturn_t ret = IRQ_NONE;
- u32 ioaddr, boguscnt = RX_RING_SIZE;
- u32 intr_status = 0;
+ u32 ioaddr, intr_status = 0;
ioaddr = ndev->base_addr;
spin_lock(&mdp->lock);
if (intr_status & cd->eesr_err_check)
sh_eth_error(ndev, intr_status);
- if (--boguscnt < 0) {
- printk(KERN_WARNING
- "%s: Too much work at interrupt, status=0x%4.4x.\n",
- ndev->name, intr_status);
- }
-
other_irq:
spin_unlock(&mdp->lock);
if (likely(status >> 16 == (status & 0xffff))) {
skb = sky2->rx_ring[sky2->rx_next].skb;
skb->ip_summed = CHECKSUM_COMPLETE;
- skb->csum = status & 0xffff;
+ skb->csum = le16_to_cpu(status);
} else {
printk(KERN_NOTICE PFX "%s: hardware receive "
"checksum problem (status = %#x)\n",
static struct net_device_stats *veth_get_stats(struct net_device *dev)
{
- struct veth_priv *priv = netdev_priv(dev);
- struct net_device_stats *dev_stats = &dev->stats;
- unsigned int cpu;
+ struct veth_priv *priv;
+ struct net_device_stats *dev_stats;
+ int cpu;
struct veth_net_stats *stats;
+ priv = netdev_priv(dev);
+ dev_stats = &dev->stats;
+
dev_stats->rx_packets = 0;
dev_stats->tx_packets = 0;
dev_stats->rx_bytes = 0;
dev_stats->tx_dropped = 0;
dev_stats->rx_dropped = 0;
- if (priv->stats)
- for_each_online_cpu(cpu) {
- stats = per_cpu_ptr(priv->stats, cpu);
+ for_each_online_cpu(cpu) {
+ stats = per_cpu_ptr(priv->stats, cpu);
- dev_stats->rx_packets += stats->rx_packets;
- dev_stats->tx_packets += stats->tx_packets;
- dev_stats->rx_bytes += stats->rx_bytes;
- dev_stats->tx_bytes += stats->tx_bytes;
- dev_stats->tx_dropped += stats->tx_dropped;
- dev_stats->rx_dropped += stats->rx_dropped;
- }
+ dev_stats->rx_packets += stats->rx_packets;
+ dev_stats->tx_packets += stats->tx_packets;
+ dev_stats->rx_bytes += stats->rx_bytes;
+ dev_stats->tx_bytes += stats->tx_bytes;
+ dev_stats->tx_dropped += stats->tx_dropped;
+ dev_stats->rx_dropped += stats->rx_dropped;
+ }
return dev_stats;
}
netif_carrier_off(dev);
netif_carrier_off(priv->peer);
- free_percpu(priv->stats);
- priv->stats = NULL;
return 0;
}
return 0;
}
+static void veth_dev_free(struct net_device *dev)
+{
+ struct veth_priv *priv;
+
+ priv = netdev_priv(dev);
+ free_percpu(priv->stats);
+ free_netdev(dev);
+}
+
static const struct net_device_ops veth_netdev_ops = {
.ndo_init = veth_dev_init,
.ndo_open = veth_open,
dev->netdev_ops = &veth_netdev_ops;
dev->ethtool_ops = &veth_ethtool_ops;
dev->features |= NETIF_F_LLTX;
- dev->destructor = free_netdev;
+ dev->destructor = veth_dev_free;
}
/*
#include <linux/sysdev.h>
#include <asm/cacheflush.h>
#include <asm/iommu.h>
-#include <asm/e820.h>
#include "pci.h"
#define ROOT_SIZE VTD_PAGE_SIZE
rmrr->end_address + 1);
}
-#ifdef CONFIG_DMAR_GFX_WA
struct iommu_prepare_data {
struct pci_dev *pdev;
int ret;
return data.ret;
}
+#ifdef CONFIG_DMAR_GFX_WA
static void __init iommu_prepare_gfx_mapping(void)
{
struct pci_dev *pdev = NULL;
static int iommu_prepare_static_identity_mapping(void)
{
- int i;
struct pci_dev *pdev = NULL;
int ret;
printk(KERN_INFO "IOMMU: Setting identity map:\n");
for_each_pci_dev(pdev) {
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
-
- if (ei->type == E820_RAM) {
- ret = iommu_prepare_identity_map(pdev,
- ei->addr, ei->addr + ei->size);
- if (ret) {
- printk(KERN_INFO "1:1 mapping to one domain failed.\n");
- return -EFAULT;
- }
- }
+ ret = iommu_prepare_with_active_regions(pdev);
+ if (ret) {
+ printk(KERN_INFO "1:1 mapping to one domain failed.\n");
+ return -EFAULT;
}
ret = domain_add_dev_info(si_domain, pdev);
if (ret)
depends on INPUT
depends on EXPERIMENTAL
depends on RFKILL || RFKILL = n
+ depends on HOTPLUG_PCI
select BACKLIGHT_CLASS_DEVICE
select HWMON
---help---
* GNU General Public License for more details.
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/input.h>
#include <linux/rfkill.h>
#include <linux/pci.h>
+#include <linux/pci_hotplug.h>
#define EEEPC_LAPTOP_VERSION "0.1"
#define EEEPC_HOTK_DEVICE_NAME "Hotkey"
#define EEEPC_HOTK_HID "ASUS010"
-#define EEEPC_LOG EEEPC_HOTK_FILE ": "
-#define EEEPC_ERR KERN_ERR EEEPC_LOG
-#define EEEPC_WARNING KERN_WARNING EEEPC_LOG
-#define EEEPC_NOTICE KERN_NOTICE EEEPC_LOG
-#define EEEPC_INFO KERN_INFO EEEPC_LOG
/*
* Definitions for Asus EeePC
u16 event_count[128]; /* count for each event */
struct input_dev *inputdev;
u16 *keycode_map;
- struct rfkill *eeepc_wlan_rfkill;
- struct rfkill *eeepc_bluetooth_rfkill;
+ struct rfkill *wlan_rfkill;
+ struct rfkill *bluetooth_rfkill;
+ struct rfkill *wwan3g_rfkill;
+ struct hotplug_slot *hotplug_slot;
};
/* The actual device the driver binds to */
},
};
+/* PCI hotplug ops */
+static int eeepc_get_adapter_status(struct hotplug_slot *slot, u8 *value);
+
+static struct hotplug_slot_ops eeepc_hotplug_slot_ops = {
+ .owner = THIS_MODULE,
+ .get_adapter_status = eeepc_get_adapter_status,
+ .get_power_status = eeepc_get_adapter_status,
+};
+
/* The backlight device /sys/class/backlight */
static struct backlight_device *eeepc_backlight_device;
if (method == NULL)
return -ENODEV;
if (write_acpi_int(ehotk->handle, method, value, NULL))
- printk(EEEPC_WARNING "Error writing %s\n", method);
+ pr_warning("Error writing %s\n", method);
}
return 0;
}
static int get_acpi(int cm)
{
- int value = -1;
+ int value = -ENODEV;
if ((ehotk->cm_supported & (0x1 << cm))) {
const char *method = cm_getv[cm];
if (method == NULL)
return -ENODEV;
if (read_acpi_int(ehotk->handle, method, &value))
- printk(EEEPC_WARNING "Error reading %s\n", method);
+ pr_warning("Error reading %s\n", method);
}
return value;
}
rv = parse_arg(buf, count, &value);
if (rv > 0)
- set_acpi(cm, value);
+ value = set_acpi(cm, value);
+ if (value < 0)
+ return value;
return rv;
}
static ssize_t show_sys_acpi(int cm, char *buf)
{
- return sprintf(buf, "%d\n", get_acpi(cm));
+ int value = get_acpi(cm);
+
+ if (value < 0)
+ return value;
+ return sprintf(buf, "%d\n", value);
}
#define EEEPC_CREATE_DEVICE_ATTR(_name, _cm) \
return -EINVAL;
}
+static void cmsg_quirk(int cm, const char *name)
+{
+ int dummy;
+
+ /* Some BIOSes do not report cm although it is avaliable.
+ Check if cm_getv[cm] works and, if yes, assume cm should be set. */
+ if (!(ehotk->cm_supported & (1 << cm))
+ && !read_acpi_int(ehotk->handle, cm_getv[cm], &dummy)) {
+ pr_info("%s (%x) not reported by BIOS,"
+ " enabling anyway\n", name, 1 << cm);
+ ehotk->cm_supported |= 1 << cm;
+ }
+}
+
+static void cmsg_quirks(void)
+{
+ cmsg_quirk(CM_ASL_LID, "LID");
+ cmsg_quirk(CM_ASL_TYPE, "TYPE");
+ cmsg_quirk(CM_ASL_PANELPOWER, "PANELPOWER");
+ cmsg_quirk(CM_ASL_TPD, "TPD");
+}
+
static int eeepc_hotk_check(void)
{
const struct key_entry *key;
if (ehotk->device->status.present) {
if (write_acpi_int(ehotk->handle, "INIT", ehotk->init_flag,
&buffer)) {
- printk(EEEPC_ERR "Hotkey initialization failed\n");
+ pr_err("Hotkey initialization failed\n");
return -ENODEV;
} else {
- printk(EEEPC_NOTICE "Hotkey init flags 0x%x\n",
- ehotk->init_flag);
+ pr_notice("Hotkey init flags 0x%x\n", ehotk->init_flag);
}
/* get control methods supported */
if (read_acpi_int(ehotk->handle, "CMSG"
, &ehotk->cm_supported)) {
- printk(EEEPC_ERR
- "Get control methods supported failed\n");
+ pr_err("Get control methods supported failed\n");
return -ENODEV;
} else {
- printk(EEEPC_INFO
- "Get control methods supported: 0x%x\n",
- ehotk->cm_supported);
+ cmsg_quirks();
+ pr_info("Get control methods supported: 0x%x\n",
+ ehotk->cm_supported);
}
ehotk->inputdev = input_allocate_device();
if (!ehotk->inputdev) {
- printk(EEEPC_INFO "Unable to allocate input device\n");
+ pr_info("Unable to allocate input device\n");
return 0;
}
ehotk->inputdev->name = "Asus EeePC extra buttons";
}
result = input_register_device(ehotk->inputdev);
if (result) {
- printk(EEEPC_INFO "Unable to register input device\n");
+ pr_info("Unable to register input device\n");
input_free_device(ehotk->inputdev);
return 0;
}
} else {
- printk(EEEPC_ERR "Hotkey device not present, aborting\n");
+ pr_err("Hotkey device not present, aborting\n");
return -EINVAL;
}
return 0;
return -1;
}
+static int eeepc_get_adapter_status(struct hotplug_slot *hotplug_slot,
+ u8 *value)
+{
+ int val = get_acpi(CM_ASL_WLAN);
+
+ if (val == 1 || val == 0)
+ *value = val;
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
static void eeepc_rfkill_hotplug(void)
{
struct pci_dev *dev;
bool blocked;
if (!bus) {
- printk(EEEPC_WARNING "Unable to find PCI bus 1?\n");
+ pr_warning("Unable to find PCI bus 1?\n");
return;
}
if (dev) {
pci_bus_assign_resources(bus);
if (pci_bus_add_device(dev))
- printk(EEEPC_ERR "Unable to hotplug wifi\n");
+ pr_err("Unable to hotplug wifi\n");
}
} else {
dev = pci_get_slot(bus, 0);
}
}
- rfkill_set_sw_state(ehotk->eeepc_wlan_rfkill, blocked);
+ rfkill_set_sw_state(ehotk->wlan_rfkill, blocked);
}
static void eeepc_rfkill_notify(acpi_handle handle, u32 event, void *data)
eeepc_rfkill_notify,
NULL);
if (ACPI_FAILURE(status))
- printk(EEEPC_WARNING
- "Failed to register notify on %s\n", node);
+ pr_warning("Failed to register notify on %s\n", node);
} else
return -ENODEV;
ACPI_SYSTEM_NOTIFY,
eeepc_rfkill_notify);
if (ACPI_FAILURE(status))
- printk(EEEPC_ERR
- "Error removing rfkill notify handler %s\n",
+ pr_err("Error removing rfkill notify handler %s\n",
node);
}
}
+static void eeepc_cleanup_pci_hotplug(struct hotplug_slot *hotplug_slot)
+{
+ kfree(hotplug_slot->info);
+ kfree(hotplug_slot);
+}
+
+static int eeepc_setup_pci_hotplug(void)
+{
+ int ret = -ENOMEM;
+ struct pci_bus *bus = pci_find_bus(0, 1);
+
+ if (!bus) {
+ pr_err("Unable to find wifi PCI bus\n");
+ return -ENODEV;
+ }
+
+ ehotk->hotplug_slot = kzalloc(sizeof(struct hotplug_slot), GFP_KERNEL);
+ if (!ehotk->hotplug_slot)
+ goto error_slot;
+
+ ehotk->hotplug_slot->info = kzalloc(sizeof(struct hotplug_slot_info),
+ GFP_KERNEL);
+ if (!ehotk->hotplug_slot->info)
+ goto error_info;
+
+ ehotk->hotplug_slot->private = ehotk;
+ ehotk->hotplug_slot->release = &eeepc_cleanup_pci_hotplug;
+ ehotk->hotplug_slot->ops = &eeepc_hotplug_slot_ops;
+ eeepc_get_adapter_status(ehotk->hotplug_slot,
+ &ehotk->hotplug_slot->info->adapter_status);
+
+ ret = pci_hp_register(ehotk->hotplug_slot, bus, 0, "eeepc-wifi");
+ if (ret) {
+ pr_err("Unable to register hotplug slot - %d\n", ret);
+ goto error_register;
+ }
+
+ return 0;
+
+error_register:
+ kfree(ehotk->hotplug_slot->info);
+error_info:
+ kfree(ehotk->hotplug_slot);
+ ehotk->hotplug_slot = NULL;
+error_slot:
+ return ret;
+}
+
static int eeepc_hotk_add(struct acpi_device *device)
{
int result;
if (!device)
return -EINVAL;
- printk(EEEPC_NOTICE EEEPC_HOTK_NAME "\n");
+ pr_notice(EEEPC_HOTK_NAME "\n");
ehotk = kzalloc(sizeof(struct eeepc_hotk), GFP_KERNEL);
if (!ehotk)
return -ENOMEM;
if (result)
goto ehotk_fail;
- eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P6");
- eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P7");
-
- if (get_acpi(CM_ASL_WLAN) != -1) {
- ehotk->eeepc_wlan_rfkill = rfkill_alloc("eeepc-wlan",
- &device->dev,
- RFKILL_TYPE_WLAN,
- &eeepc_rfkill_ops,
- (void *)CM_ASL_WLAN);
-
- if (!ehotk->eeepc_wlan_rfkill)
- goto wlan_fail;
-
- rfkill_init_sw_state(ehotk->eeepc_wlan_rfkill,
- get_acpi(CM_ASL_WLAN) != 1);
- result = rfkill_register(ehotk->eeepc_wlan_rfkill);
- if (result)
- goto wlan_fail;
- }
-
- if (get_acpi(CM_ASL_BLUETOOTH) != -1) {
- ehotk->eeepc_bluetooth_rfkill =
- rfkill_alloc("eeepc-bluetooth",
- &device->dev,
- RFKILL_TYPE_BLUETOOTH,
- &eeepc_rfkill_ops,
- (void *)CM_ASL_BLUETOOTH);
-
- if (!ehotk->eeepc_bluetooth_rfkill)
- goto bluetooth_fail;
-
- rfkill_init_sw_state(ehotk->eeepc_bluetooth_rfkill,
- get_acpi(CM_ASL_BLUETOOTH) != 1);
- result = rfkill_register(ehotk->eeepc_bluetooth_rfkill);
- if (result)
- goto bluetooth_fail;
- }
-
return 0;
- bluetooth_fail:
- rfkill_destroy(ehotk->eeepc_bluetooth_rfkill);
- rfkill_unregister(ehotk->eeepc_wlan_rfkill);
- wlan_fail:
- rfkill_destroy(ehotk->eeepc_wlan_rfkill);
- eeepc_unregister_rfkill_notifier("\\_SB.PCI0.P0P6");
- eeepc_unregister_rfkill_notifier("\\_SB.PCI0.P0P7");
ehotk_fail:
kfree(ehotk);
ehotk = NULL;
if (!device || !acpi_driver_data(device))
return -EINVAL;
- eeepc_unregister_rfkill_notifier("\\_SB.PCI0.P0P6");
- eeepc_unregister_rfkill_notifier("\\_SB.PCI0.P0P7");
-
kfree(ehotk);
return 0;
}
static int eeepc_hotk_resume(struct acpi_device *device)
{
- if (ehotk->eeepc_wlan_rfkill) {
+ if (ehotk->wlan_rfkill) {
bool wlan;
/* Workaround - it seems that _PTS disables the wireless
wlan = get_acpi(CM_ASL_WLAN);
set_acpi(CM_ASL_WLAN, wlan);
- rfkill_set_sw_state(ehotk->eeepc_wlan_rfkill,
- wlan != 1);
+ rfkill_set_sw_state(ehotk->wlan_rfkill, wlan != 1);
eeepc_rfkill_hotplug();
}
- if (ehotk->eeepc_bluetooth_rfkill)
- rfkill_set_sw_state(ehotk->eeepc_bluetooth_rfkill,
+ if (ehotk->bluetooth_rfkill)
+ rfkill_set_sw_state(ehotk->bluetooth_rfkill,
get_acpi(CM_ASL_BLUETOOTH) != 1);
return 0;
static void eeepc_rfkill_exit(void)
{
- if (ehotk->eeepc_wlan_rfkill)
- rfkill_unregister(ehotk->eeepc_wlan_rfkill);
- if (ehotk->eeepc_bluetooth_rfkill)
- rfkill_unregister(ehotk->eeepc_bluetooth_rfkill);
+ eeepc_unregister_rfkill_notifier("\\_SB.PCI0.P0P6");
+ eeepc_unregister_rfkill_notifier("\\_SB.PCI0.P0P7");
+ if (ehotk->wlan_rfkill)
+ rfkill_unregister(ehotk->wlan_rfkill);
+ if (ehotk->bluetooth_rfkill)
+ rfkill_unregister(ehotk->bluetooth_rfkill);
+ if (ehotk->wwan3g_rfkill)
+ rfkill_unregister(ehotk->wwan3g_rfkill);
+ if (ehotk->hotplug_slot)
+ pci_hp_deregister(ehotk->hotplug_slot);
}
static void eeepc_input_exit(void)
platform_driver_unregister(&platform_driver);
}
+static int eeepc_new_rfkill(struct rfkill **rfkill,
+ const char *name, struct device *dev,
+ enum rfkill_type type, int cm)
+{
+ int result;
+
+ result = get_acpi(cm);
+ if (result < 0)
+ return result;
+
+ *rfkill = rfkill_alloc(name, dev, type,
+ &eeepc_rfkill_ops, (void *)(unsigned long)cm);
+
+ if (!*rfkill)
+ return -EINVAL;
+
+ rfkill_init_sw_state(*rfkill, get_acpi(cm) != 1);
+ result = rfkill_register(*rfkill);
+ if (result) {
+ rfkill_destroy(*rfkill);
+ *rfkill = NULL;
+ return result;
+ }
+ return 0;
+}
+
+
+static int eeepc_rfkill_init(struct device *dev)
+{
+ int result = 0;
+
+ eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P6");
+ eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P7");
+
+ result = eeepc_new_rfkill(&ehotk->wlan_rfkill,
+ "eeepc-wlan", dev,
+ RFKILL_TYPE_WLAN, CM_ASL_WLAN);
+
+ if (result && result != -ENODEV)
+ goto exit;
+
+ result = eeepc_new_rfkill(&ehotk->bluetooth_rfkill,
+ "eeepc-bluetooth", dev,
+ RFKILL_TYPE_BLUETOOTH, CM_ASL_BLUETOOTH);
+
+ if (result && result != -ENODEV)
+ goto exit;
+
+ result = eeepc_new_rfkill(&ehotk->wwan3g_rfkill,
+ "eeepc-wwan3g", dev,
+ RFKILL_TYPE_WWAN, CM_ASL_3G);
+
+ if (result && result != -ENODEV)
+ goto exit;
+
+ result = eeepc_setup_pci_hotplug();
+ /*
+ * If we get -EBUSY then something else is handling the PCI hotplug -
+ * don't fail in this case
+ */
+ if (result == -EBUSY)
+ result = 0;
+
+exit:
+ if (result && result != -ENODEV)
+ eeepc_rfkill_exit();
+ return result;
+}
+
static int eeepc_backlight_init(struct device *dev)
{
struct backlight_device *bd;
bd = backlight_device_register(EEEPC_HOTK_FILE, dev,
NULL, &eeepcbl_ops);
if (IS_ERR(bd)) {
- printk(EEEPC_ERR
- "Could not register eeepc backlight device\n");
+ pr_err("Could not register eeepc backlight device\n");
eeepc_backlight_device = NULL;
return PTR_ERR(bd);
}
hwmon = hwmon_device_register(dev);
if (IS_ERR(hwmon)) {
- printk(EEEPC_ERR
- "Could not register eeepc hwmon device\n");
+ pr_err("Could not register eeepc hwmon device\n");
eeepc_hwmon_device = NULL;
return PTR_ERR(hwmon);
}
acpi_bus_unregister_driver(&eeepc_hotk_driver);
return -ENODEV;
}
- dev = acpi_get_physical_device(ehotk->device->handle);
-
- if (!acpi_video_backlight_support()) {
- result = eeepc_backlight_init(dev);
- if (result)
- goto fail_backlight;
- } else
- printk(EEEPC_INFO "Backlight controlled by ACPI video "
- "driver\n");
-
- result = eeepc_hwmon_init(dev);
- if (result)
- goto fail_hwmon;
eeepc_enable_camera();
&platform_attribute_group);
if (result)
goto fail_sysfs;
+
+ dev = &platform_device->dev;
+
+ if (!acpi_video_backlight_support()) {
+ result = eeepc_backlight_init(dev);
+ if (result)
+ goto fail_backlight;
+ } else
+ pr_info("Backlight controlled by ACPI video "
+ "driver\n");
+
+ result = eeepc_hwmon_init(dev);
+ if (result)
+ goto fail_hwmon;
+
+ result = eeepc_rfkill_init(dev);
+ if (result)
+ goto fail_rfkill;
+
return 0;
+fail_rfkill:
+ eeepc_hwmon_exit();
+fail_hwmon:
+ eeepc_backlight_exit();
+fail_backlight:
+ sysfs_remove_group(&platform_device->dev.kobj,
+ &platform_attribute_group);
fail_sysfs:
platform_device_del(platform_device);
fail_platform_device2:
fail_platform_device1:
platform_driver_unregister(&platform_driver);
fail_platform_driver:
- eeepc_hwmon_exit();
-fail_hwmon:
- eeepc_backlight_exit();
-fail_backlight:
eeepc_input_exit();
- eeepc_rfkill_exit();
return result;
}
static int acm_tty_open(struct tty_struct *tty, struct file *filp)
{
struct acm *acm;
- int rv = -EINVAL;
+ int rv = -ENODEV;
int i;
dbg("Entering acm_tty_open.");
/* Perform the closing process and see if we need to do the hardware
shutdown */
- if (tty_port_close_start(&acm->port, tty, filp) == 0)
+ if (!acm || tty_port_close_start(&acm->port, tty, filp) == 0)
return;
acm_port_down(acm, 0);
tty_port_close_end(&acm->port, tty);
{
struct usb_serial_port *port = tty->driver_data;
+ if (!port)
+ return;
+
dbg("%s - port %d", __func__, port->number);
lcd->power = FB_BLANK_POWERDOWN;
lcd->mode = MODE_VGA; /* default to VGA */
- lcd->buf = kmalloc(TDO24M_SPI_BUFF_SIZE, sizeof(GFP_KERNEL));
+ lcd->buf = kmalloc(TDO24M_SPI_BUFF_SIZE, GFP_KERNEL);
if (lcd->buf == NULL) {
kfree(lcd);
return -ENOMEM;
*/
static int wdrtas_get_temperature(void)
{
- long result;
+ int result;
int temperature = 0;
- result = rtas_call(wdrtas_token_get_sensor_state, 2, 2,
- (void *)__pa(&temperature),
- WDRTAS_THERMAL_SENSOR, 0);
+ result = rtas_get_sensor(WDRTAS_THERMAL_SENSOR, 0, &temperature);
if (result < 0)
printk(KERN_WARNING "wdrtas: reading the thermal sensor "
- "faild: %li\n", result);
+ "failed: %i\n", result);
else
temperature = ((temperature * 9) / 5) + 32; /* fahrenheit */
on by default if server supports it). Add forceuid and forcegid
mount options (so that when negotiating unix extensions specifying
which uid mounted does not immediately force the server's reported
-uids to be overridden).
+uids to be overridden). Add support for scope moutn parm.
Version 1.58
------------
#define ASN1_OJI 6 /* Object Identifier */
#define ASN1_OJD 7 /* Object Description */
#define ASN1_EXT 8 /* External */
+#define ASN1_ENUM 10 /* Enumerated */
#define ASN1_SEQ 16 /* Sequence */
#define ASN1_SET 17 /* Set */
#define ASN1_NUMSTR 18 /* Numerical String */
#define SPNEGO_OID_LEN 7
#define NTLMSSP_OID_LEN 10
#define KRB5_OID_LEN 7
+#define KRB5U2U_OID_LEN 8
#define MSKRB5_OID_LEN 7
static unsigned long SPNEGO_OID[7] = { 1, 3, 6, 1, 5, 5, 2 };
static unsigned long NTLMSSP_OID[10] = { 1, 3, 6, 1, 4, 1, 311, 2, 2, 10 };
static unsigned long KRB5_OID[7] = { 1, 2, 840, 113554, 1, 2, 2 };
+static unsigned long KRB5U2U_OID[8] = { 1, 2, 840, 113554, 1, 2, 2, 3 };
static unsigned long MSKRB5_OID[7] = { 1, 2, 840, 48018, 1, 2, 2 };
/*
return 1;
}
+#if 0 /* will be needed later by spnego decoding/encoding of ntlmssp */
+static unsigned char
+asn1_enum_decode(struct asn1_ctx *ctx, __le32 *val)
+{
+ unsigned char ch;
+
+ if (ctx->pointer >= ctx->end) {
+ ctx->error = ASN1_ERR_DEC_EMPTY;
+ return 0;
+ }
+
+ ch = *(ctx->pointer)++; /* ch has 0xa, ptr points to lenght octet */
+ if ((ch) == ASN1_ENUM) /* if ch value is ENUM, 0xa */
+ *val = *(++(ctx->pointer)); /* value has enum value */
+ else
+ return 0;
+
+ ctx->pointer++;
+ return 1;
+}
+#endif
+
static unsigned char
asn1_tag_decode(struct asn1_ctx *ctx, unsigned int *tag)
{
unsigned int cls, con, tag, oidlen, rc;
bool use_ntlmssp = false;
bool use_kerberos = false;
+ bool use_kerberosu2u = false;
bool use_mskerberos = false;
- *secType = NTLM; /* BB eventually make Kerberos or NLTMSSP the default*/
-
/* cifs_dump_mem(" Received SecBlob ", security_blob, length); */
asn1_open(&ctx, security_blob, length);
return 0;
}
+ /* SPNEGO */
if (asn1_header_decode(&ctx, &end, &cls, &con, &tag) == 0) {
cFYI(1, ("Error decoding negTokenInit"));
return 0;
return 0;
}
+ /* negTokenInit */
if (asn1_header_decode(&ctx, &end, &cls, &con, &tag) == 0) {
cFYI(1, ("Error decoding negTokenInit"));
return 0;
return 0;
}
+ /* sequence */
if (asn1_header_decode(&ctx, &end, &cls, &con, &tag) == 0) {
cFYI(1, ("Error decoding 2nd part of negTokenInit"));
return 0;
return 0;
}
+ /* sequence of */
if (asn1_header_decode
(&ctx, &sequence_end, &cls, &con, &tag) == 0) {
cFYI(1, ("Error decoding 2nd part of negTokenInit"));
return 0;
}
+ /* list of security mechanisms */
while (!asn1_eoc_decode(&ctx, sequence_end)) {
rc = asn1_header_decode(&ctx, &end, &cls, &con, &tag);
if (!rc) {
if (compare_oid(oid, oidlen, MSKRB5_OID,
MSKRB5_OID_LEN) &&
- !use_kerberos)
+ !use_mskerberos)
use_mskerberos = true;
+ else if (compare_oid(oid, oidlen, KRB5U2U_OID,
+ KRB5U2U_OID_LEN) &&
+ !use_kerberosu2u)
+ use_kerberosu2u = true;
else if (compare_oid(oid, oidlen, KRB5_OID,
KRB5_OID_LEN) &&
- !use_mskerberos)
+ !use_kerberos)
use_kerberos = true;
else if (compare_oid(oid, oidlen, NTLMSSP_OID,
NTLMSSP_OID_LEN))
}
}
+ /* mechlistMIC */
if (asn1_header_decode(&ctx, &end, &cls, &con, &tag) == 0) {
+ /* Check if we have reached the end of the blob, but with
+ no mechListMic (e.g. NTLMSSP instead of KRB5) */
+ if (ctx.error == ASN1_ERR_DEC_EMPTY)
+ goto decode_negtoken_exit;
cFYI(1, ("Error decoding last part negTokenInit exit3"));
return 0;
} else if ((cls != ASN1_CTX) || (con != ASN1_CON)) {
cls, con, tag, end, *end));
return 0;
}
+
+ /* sequence */
if (asn1_header_decode(&ctx, &end, &cls, &con, &tag) == 0) {
cFYI(1, ("Error decoding last part negTokenInit exit5"));
return 0;
cls, con, tag, end, *end));
}
+ /* sequence of */
if (asn1_header_decode(&ctx, &end, &cls, &con, &tag) == 0) {
cFYI(1, ("Error decoding last part negTokenInit exit 7"));
return 0;
cls, con, tag, end, *end));
return 0;
}
+
+ /* general string */
if (asn1_header_decode(&ctx, &end, &cls, &con, &tag) == 0) {
cFYI(1, ("Error decoding last part negTokenInit exit9"));
return 0;
}
cFYI(1, ("Need to call asn1_octets_decode() function for %s",
ctx.pointer)); /* is this UTF-8 or ASCII? */
-
+decode_negtoken_exit:
if (use_kerberos)
*secType = Kerberos;
else if (use_mskerberos)
*secType = MSKerberos;
else if (use_ntlmssp)
- *secType = NTLMSSP;
+ *secType = RawNTLMSSP;
return 1;
}
kmem_cache_free(cifs_inode_cachep, CIFS_I(inode));
}
+static void
+cifs_show_address(struct seq_file *s, struct TCP_Server_Info *server)
+{
+ seq_printf(s, ",addr=");
+
+ switch (server->addr.sockAddr.sin_family) {
+ case AF_INET:
+ seq_printf(s, "%pI4", &server->addr.sockAddr.sin_addr.s_addr);
+ break;
+ case AF_INET6:
+ seq_printf(s, "%pI6",
+ &server->addr.sockAddr6.sin6_addr.s6_addr);
+ if (server->addr.sockAddr6.sin6_scope_id)
+ seq_printf(s, "%%%u",
+ server->addr.sockAddr6.sin6_scope_id);
+ break;
+ default:
+ seq_printf(s, "(unknown)");
+ }
+}
+
/*
* cifs_show_options() is for displaying mount options in /proc/mounts.
* Not all settable options are displayed but most of the important
{
struct cifs_sb_info *cifs_sb;
struct cifsTconInfo *tcon;
- struct TCP_Server_Info *server;
cifs_sb = CIFS_SB(m->mnt_sb);
+ tcon = cifs_sb->tcon;
- if (cifs_sb) {
- tcon = cifs_sb->tcon;
- if (tcon) {
- seq_printf(s, ",unc=%s", cifs_sb->tcon->treeName);
- if (tcon->ses) {
- if (tcon->ses->userName)
- seq_printf(s, ",username=%s",
- tcon->ses->userName);
- if (tcon->ses->domainName)
- seq_printf(s, ",domain=%s",
- tcon->ses->domainName);
- server = tcon->ses->server;
- if (server) {
- seq_printf(s, ",addr=");
- switch (server->addr.sockAddr6.
- sin6_family) {
- case AF_INET6:
- seq_printf(s, "%pI6",
- &server->addr.sockAddr6.sin6_addr);
- break;
- case AF_INET:
- seq_printf(s, "%pI4",
- &server->addr.sockAddr.sin_addr.s_addr);
- break;
- }
- }
- }
- if ((cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_UID) ||
- !(tcon->unix_ext))
- seq_printf(s, ",uid=%d", cifs_sb->mnt_uid);
- if ((cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_GID) ||
- !(tcon->unix_ext))
- seq_printf(s, ",gid=%d", cifs_sb->mnt_gid);
- if (!tcon->unix_ext) {
- seq_printf(s, ",file_mode=0%o,dir_mode=0%o",
+ seq_printf(s, ",unc=%s", cifs_sb->tcon->treeName);
+ if (tcon->ses->userName)
+ seq_printf(s, ",username=%s", tcon->ses->userName);
+ if (tcon->ses->domainName)
+ seq_printf(s, ",domain=%s", tcon->ses->domainName);
+
+ seq_printf(s, ",uid=%d", cifs_sb->mnt_uid);
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_UID)
+ seq_printf(s, ",forceuid");
+
+ seq_printf(s, ",gid=%d", cifs_sb->mnt_gid);
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_GID)
+ seq_printf(s, ",forcegid");
+
+ cifs_show_address(s, tcon->ses->server);
+
+ if (!tcon->unix_ext)
+ seq_printf(s, ",file_mode=0%o,dir_mode=0%o",
cifs_sb->mnt_file_mode,
cifs_sb->mnt_dir_mode);
- }
- if (tcon->seal)
- seq_printf(s, ",seal");
- if (tcon->nocase)
- seq_printf(s, ",nocase");
- if (tcon->retry)
- seq_printf(s, ",hard");
- }
- if (cifs_sb->prepath)
- seq_printf(s, ",prepath=%s", cifs_sb->prepath);
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_POSIX_PATHS)
- seq_printf(s, ",posixpaths");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_SET_UID)
- seq_printf(s, ",setuids");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_SERVER_INUM)
- seq_printf(s, ",serverino");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_DIRECT_IO)
- seq_printf(s, ",directio");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_XATTR)
- seq_printf(s, ",nouser_xattr");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MAP_SPECIAL_CHR)
- seq_printf(s, ",mapchars");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_UNX_EMUL)
- seq_printf(s, ",sfu");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_BRL)
- seq_printf(s, ",nobrl");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_CIFS_ACL)
- seq_printf(s, ",cifsacl");
- if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_DYNPERM)
- seq_printf(s, ",dynperm");
- if (m->mnt_sb->s_flags & MS_POSIXACL)
- seq_printf(s, ",acl");
-
- seq_printf(s, ",rsize=%d", cifs_sb->rsize);
- seq_printf(s, ",wsize=%d", cifs_sb->wsize);
- }
+ if (tcon->seal)
+ seq_printf(s, ",seal");
+ if (tcon->nocase)
+ seq_printf(s, ",nocase");
+ if (tcon->retry)
+ seq_printf(s, ",hard");
+ if (cifs_sb->prepath)
+ seq_printf(s, ",prepath=%s", cifs_sb->prepath);
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_POSIX_PATHS)
+ seq_printf(s, ",posixpaths");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_SET_UID)
+ seq_printf(s, ",setuids");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_SERVER_INUM)
+ seq_printf(s, ",serverino");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_DIRECT_IO)
+ seq_printf(s, ",directio");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_XATTR)
+ seq_printf(s, ",nouser_xattr");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MAP_SPECIAL_CHR)
+ seq_printf(s, ",mapchars");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_UNX_EMUL)
+ seq_printf(s, ",sfu");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_BRL)
+ seq_printf(s, ",nobrl");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_CIFS_ACL)
+ seq_printf(s, ",cifsacl");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_DYNPERM)
+ seq_printf(s, ",dynperm");
+ if (m->mnt_sb->s_flags & MS_POSIXACL)
+ seq_printf(s, ",acl");
+
+ seq_printf(s, ",rsize=%d", cifs_sb->rsize);
+ seq_printf(s, ",wsize=%d", cifs_sb->wsize);
+
return 0;
}
if (tcon == NULL)
return;
- lock_kernel();
read_lock(&cifs_tcp_ses_lock);
- if (tcon->tc_count == 1)
+ if ((tcon->tc_count > 1) || (tcon->tidStatus == CifsExiting)) {
+ /* we have other mounts to same share or we have
+ already tried to force umount this and woken up
+ all waiting network requests, nothing to do */
+ read_unlock(&cifs_tcp_ses_lock);
+ return;
+ } else if (tcon->tc_count == 1)
tcon->tidStatus = CifsExiting;
read_unlock(&cifs_tcp_ses_lock);
wake_up_all(&tcon->ses->server->response_q);
msleep(1);
}
-/* BB FIXME - finish add checks for tidStatus BB */
- unlock_kernel();
return;
}
NTLM, /* Legacy NTLM012 auth with NTLM hash */
NTLMv2, /* Legacy NTLM auth with NTLMv2 hash */
RawNTLMSSP, /* NTLMSSP without SPNEGO, NTLMv2 hash */
- NTLMSSP, /* NTLMSSP via SPNEGO, NTLMv2 hash */
+/* NTLMSSP, */ /* can use rawNTLMSSP instead of NTLMSSP via SPNEGO */
Kerberos, /* Kerberos via SPNEGO */
MSKerberos, /* MS Kerberos via SPNEGO */
};
extern unsigned int smbCalcSize_LE(struct smb_hdr *ptr);
extern int decode_negTokenInit(unsigned char *security_blob, int length,
enum securityEnum *secType);
-extern int cifs_inet_pton(const int, const char *source, void *dst);
+extern int cifs_convert_address(char *src, void *dst);
extern int map_smb_to_linux_error(struct smb_hdr *smb, int logErr);
extern void header_assemble(struct smb_hdr *, char /* command */ ,
const struct cifsTconInfo *, int /* length of
else if (secFlags & CIFSSEC_MAY_KRB5)
server->secType = Kerberos;
else if (secFlags & CIFSSEC_MAY_NTLMSSP)
- server->secType = NTLMSSP;
+ server->secType = RawNTLMSSP;
else if (secFlags & CIFSSEC_MAY_LANMAN)
server->secType = LANMAN;
/* #ifdef CONFIG_CIFS_EXPERIMENTAL
* the tcon is no longer on the list, so no need to take lock before
* checking this.
*/
- if (tcon->need_reconnect)
+ if ((tcon->need_reconnect) || (tcon->ses->need_reconnect))
return 0;
rc = small_smb_init(SMB_COM_TREE_DISCONNECT, 0, tcon,
mode_t file_mode;
mode_t dir_mode;
unsigned secFlg;
- bool rw:1;
bool retry:1;
bool intr:1;
bool setuids:1;
vol->dir_mode = vol->file_mode = S_IRUGO | S_IXUGO | S_IWUSR;
/* vol->retry default is 0 (i.e. "soft" limited retry not hard retry) */
- vol->rw = true;
/* default is always to request posix paths. */
vol->posix_paths = 1;
/* default to using server inode numbers where available */
} else if (strnicmp(data, "guest", 5) == 0) {
/* ignore */
} else if (strnicmp(data, "rw", 2) == 0) {
- vol->rw = true;
+ /* ignore */
+ } else if (strnicmp(data, "ro", 2) == 0) {
+ /* ignore */
} else if (strnicmp(data, "noblocksend", 11) == 0) {
vol->noblocksnd = 1;
} else if (strnicmp(data, "noautotune", 10) == 0) {
parse these options again and set anything and it
is ok to just ignore them */
continue;
- } else if (strnicmp(data, "ro", 2) == 0) {
- vol->rw = false;
} else if (strnicmp(data, "hard", 4) == 0) {
vol->retry = 1;
} else if (strnicmp(data, "soft", 4) == 0) {
server->addr.sockAddr.sin_addr.s_addr))
continue;
else if (addr->ss_family == AF_INET6 &&
- !ipv6_addr_equal(&server->addr.sockAddr6.sin6_addr,
- &addr6->sin6_addr))
+ (!ipv6_addr_equal(&server->addr.sockAddr6.sin6_addr,
+ &addr6->sin6_addr) ||
+ server->addr.sockAddr6.sin6_scope_id !=
+ addr6->sin6_scope_id))
continue;
++server->srv_count;
memset(&addr, 0, sizeof(struct sockaddr_storage));
- if (volume_info->UNCip && volume_info->UNC) {
- rc = cifs_inet_pton(AF_INET, volume_info->UNCip,
- &sin_server->sin_addr.s_addr);
-
- if (rc <= 0) {
- /* not ipv4 address, try ipv6 */
- rc = cifs_inet_pton(AF_INET6, volume_info->UNCip,
- &sin_server6->sin6_addr.in6_u);
- if (rc > 0)
- addr.ss_family = AF_INET6;
- } else {
- addr.ss_family = AF_INET;
- }
+ cFYI(1, ("UNC: %s ip: %s", volume_info->UNC, volume_info->UNCip));
- if (rc <= 0) {
+ if (volume_info->UNCip && volume_info->UNC) {
+ rc = cifs_convert_address(volume_info->UNCip, &addr);
+ if (!rc) {
/* we failed translating address */
rc = -EINVAL;
goto out_err;
}
-
- cFYI(1, ("UNC: %s ip: %s", volume_info->UNC,
- volume_info->UNCip));
} else if (volume_info->UNCip) {
/* BB using ip addr as tcp_ses name to connect to the
DFS root below */
cFYI(1, ("attempting ipv6 connect"));
/* BB should we allow ipv6 on port 139? */
/* other OS never observed in Wild doing 139 with v6 */
+ sin_server6->sin6_port = htons(volume_info->port);
memcpy(&tcp_ses->addr.sockAddr6, sin_server6,
sizeof(struct sockaddr_in6));
- sin_server6->sin6_port = htons(volume_info->port);
rc = ipv6_connect(tcp_ses);
} else {
+ sin_server->sin_port = htons(volume_info->port);
memcpy(&tcp_ses->addr.sockAddr, sin_server,
sizeof(struct sockaddr_in));
- sin_server->sin_port = htons(volume_info->port);
rc = ipv4_connect(tcp_ses);
}
if (rc < 0) {
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
if (oplockEnabled)
buf = kmalloc(sizeof(FILE_ALL_INFO), GFP_KERNEL);
if (buf == NULL) {
kfree(full_path);
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
rc = CIFSSMBOpen(xid, pTcon, full_path,
* 0 - name is not IP
*/
static int
-is_ip(const char *name)
+is_ip(char *name)
{
- int rc;
- struct sockaddr_in sin_server;
- struct sockaddr_in6 sin_server6;
-
- rc = cifs_inet_pton(AF_INET, name,
- &sin_server.sin_addr.s_addr);
-
- if (rc <= 0) {
- /* not ipv4 address, try ipv6 */
- rc = cifs_inet_pton(AF_INET6, name,
- &sin_server6.sin6_addr.in6_u);
- if (rc > 0)
- return 1;
- } else {
- return 1;
- }
- /* we failed translating address */
- return 0;
+ struct sockaddr_storage ss;
+
+ return cifs_convert_address(name, &ss);
}
static int
ip[datalen] = '\0';
/* make sure this looks like an address */
- if (!is_ip((const char *) ip)) {
+ if (!is_ip(ip)) {
kfree(ip);
return -EINVAL;
}
pCifsInode = CIFS_I(file->f_path.dentry->d_inode);
pCifsFile = cifs_fill_filedata(file);
if (pCifsFile) {
+ rc = 0;
FreeXid(xid);
- return 0;
+ return rc;
}
full_path = build_path_from_dentry(file->f_path.dentry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
cFYI(1, ("inode = 0x%p file flags are 0x%x for %s",
return -EBADF;
xid = GetXid();
- mutex_unlock(&pCifsFile->fh_mutex);
+ mutex_lock(&pCifsFile->fh_mutex);
if (!pCifsFile->invalidHandle) {
- mutex_lock(&pCifsFile->fh_mutex);
+ mutex_unlock(&pCifsFile->fh_mutex);
+ rc = 0;
FreeXid(xid);
- return 0;
+ return rc;
}
if (file->f_path.dentry == NULL) {
if (full_path == NULL) {
rc = -ENOMEM;
reopen_error_exit:
- mutex_lock(&pCifsFile->fh_mutex);
+ mutex_unlock(&pCifsFile->fh_mutex);
FreeXid(xid);
return rc;
}
cifs_sb->local_nls, cifs_sb->mnt_cifs_flags &
CIFS_MOUNT_MAP_SPECIAL_CHR);
if (rc) {
- mutex_lock(&pCifsFile->fh_mutex);
+ mutex_unlock(&pCifsFile->fh_mutex);
cFYI(1, ("cifs_open returned 0x%x", rc));
cFYI(1, ("oplock: %d", oplock));
} else {
reopen_success:
pCifsFile->netfid = netfid;
pCifsFile->invalidHandle = false;
- mutex_lock(&pCifsFile->fh_mutex);
+ mutex_unlock(&pCifsFile->fh_mutex);
pCifsInode = CIFS_I(inode);
if (pCifsInode) {
if (can_flush) {
tcon = cifs_sb->tcon;
if (file->private_data == NULL) {
+ rc = -EBADF;
FreeXid(xid);
- return -EBADF;
+ return rc;
}
netfid = ((struct cifsFileInfo *)file->private_data)->netfid;
pTcon = cifs_sb->tcon;
if (file->private_data == NULL) {
+ rc = -EBADF;
FreeXid(xid);
- return -EBADF;
+ return rc;
}
open_file = (struct cifsFileInfo *)file->private_data;
pTcon = cifs_sb->tcon;
if (file->private_data == NULL) {
+ rc = -EBADF;
FreeXid(xid);
- return -EBADF;
+ return rc;
}
open_file = (struct cifsFileInfo *)file->private_data;
xid = GetXid();
if (file->private_data == NULL) {
+ rc = -EBADF;
FreeXid(xid);
- return -EBADF;
+ return rc;
}
open_file = (struct cifsFileInfo *)file->private_data;
cifs_sb = CIFS_SB(file->f_path.dentry->d_sb);
xid = GetXid();
if (file->private_data == NULL) {
+ rc = -EBADF;
FreeXid(xid);
- return -EBADF;
+ return rc;
}
cFYI(1, ("readpage %p at offset %d 0x%x\n",
* sb->s_vfs_rename_mutex here */
full_path = build_path_from_dentry(dentry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
if ((tcon->ses->capabilities & CAP_UNIX) &&
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
if ((pTcon->ses->capabilities & CAP_UNIX) &&
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
rc = CIFSSMBRmDir(xid, pTcon, full_path, cifs_sb->local_nls,
since that would deadlock */
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
cFYI(1, ("Revalidate: %s inode 0x%p count %d dentry: 0x%p d_time %ld "
"jiffies %ld", full_path, direntry->d_inode,
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
/*
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
cFYI(1, ("Full path: %s", full_path));
{0, 0}
};
-/* Convert string containing dotted ip address to binary form */
-/* returns 0 if invalid address */
-
-int
+/*
+ * Convert a string containing text IPv4 or IPv6 address to binary form.
+ *
+ * Returns 0 on failure.
+ */
+static int
cifs_inet_pton(const int address_family, const char *cp, void *dst)
{
int ret = 0;
return ret;
}
+/*
+ * Try to convert a string to an IPv4 address and then attempt to convert
+ * it to an IPv6 address if that fails. Set the family field if either
+ * succeeds. If it's an IPv6 address and it has a '%' sign in it, try to
+ * treat the part following it as a numeric sin6_scope_id.
+ *
+ * Returns 0 on failure.
+ */
+int
+cifs_convert_address(char *src, void *dst)
+{
+ int rc;
+ char *pct, *endp;
+ struct sockaddr_in *s4 = (struct sockaddr_in *) dst;
+ struct sockaddr_in6 *s6 = (struct sockaddr_in6 *) dst;
+
+ /* IPv4 address */
+ if (cifs_inet_pton(AF_INET, src, &s4->sin_addr.s_addr)) {
+ s4->sin_family = AF_INET;
+ return 1;
+ }
+
+ /* temporarily terminate string */
+ pct = strchr(src, '%');
+ if (pct)
+ *pct = '\0';
+
+ rc = cifs_inet_pton(AF_INET6, src, &s6->sin6_addr.s6_addr);
+
+ /* repair temp termination (if any) and make pct point to scopeid */
+ if (pct)
+ *pct++ = '%';
+
+ if (!rc)
+ return rc;
+
+ s6->sin6_family = AF_INET6;
+ if (pct) {
+ s6->sin6_scope_id = (u32) simple_strtoul(pct, &endp, 0);
+ if (!*pct || *endp)
+ return 0;
+ }
+
+ return rc;
+}
+
/*****************************************************************************
convert a NT status code to a dos class/code
*****************************************************************************/
#endif /* CONFIG_CIFS_UPCALL */
} else {
#ifdef CONFIG_CIFS_EXPERIMENTAL
- if ((experimEnabled > 1) && (type == RawNTLMSSP)) {
+ if (type == RawNTLMSSP) {
if ((pSMB->req.hdr.Flags2 & SMBFLG2_UNICODE) == 0) {
cERROR(1, ("NTLMSSP requires Unicode support"));
rc = -ENOSYS;
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
if (ea_name == NULL) {
cFYI(1, ("Null xattr names not supported"));
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
/* return dos attributes as pseudo xattr */
/* return alt name if available as pseudo attr */
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
/* return dos attributes as pseudo xattr */
/* return alt name if available as pseudo attr */
full_path = build_path_from_dentry(direntry);
if (full_path == NULL) {
+ rc = -ENOMEM;
FreeXid(xid);
- return -ENOMEM;
+ return rc;
}
/* return dos attributes as pseudo xattr */
/* return alt name if available as pseudo attr */
goto exit;
}
filp = nameidata_to_filp(&nd, open_flag);
+ if (IS_ERR(filp))
+ ima_counts_put(&nd.path,
+ acc_mode & (MAY_READ | MAY_WRITE |
+ MAY_EXEC));
mnt_drop_write(nd.path.mnt);
if (nd.root.mnt)
path_put(&nd.root);
goto exit;
}
filp = nameidata_to_filp(&nd, open_flag);
+ if (IS_ERR(filp))
+ ima_counts_put(&nd.path,
+ acc_mode & (MAY_READ | MAY_WRITE | MAY_EXEC));
/*
* It is now safe to drop the mnt write
* because the filp has had a write taken
} __attribute__((packed));
/* 00=16:10, 01=4:3, 10=5:4, 11=16:9 */
-#define EDID_TIMING_ASPECT_SHIFT 0
+#define EDID_TIMING_ASPECT_SHIFT 6
#define EDID_TIMING_ASPECT_MASK (0x3 << EDID_TIMING_ASPECT_SHIFT)
/* need to add 60 */
-#define EDID_TIMING_VFREQ_SHIFT 2
+#define EDID_TIMING_VFREQ_SHIFT 0
#define EDID_TIMING_VFREQ_MASK (0x3f << EDID_TIMING_VFREQ_SHIFT)
struct std_timing {
u8 vfreq_aspect;
} __attribute__((packed));
-#define DRM_EDID_PT_HSYNC_POSITIVE (1 << 6)
-#define DRM_EDID_PT_VSYNC_POSITIVE (1 << 5)
+#define DRM_EDID_PT_HSYNC_POSITIVE (1 << 1)
+#define DRM_EDID_PT_VSYNC_POSITIVE (1 << 2)
#define DRM_EDID_PT_SEPARATE_SYNC (3 << 3)
-#define DRM_EDID_PT_STEREO (1 << 2)
-#define DRM_EDID_PT_INTERLACED (1 << 1)
+#define DRM_EDID_PT_STEREO (1 << 5)
+#define DRM_EDID_PT_INTERLACED (1 << 7)
/* If detailed data is pixel timing */
struct detailed_pixel_timing {
} __attribute__((packed));
struct detailed_data_wpindex {
- u8 white_xy_lo; /* Upper 2 bits each */
+ u8 white_yx_lo; /* Lower 2 bits each */
u8 white_x_hi;
u8 white_y_hi;
u8 gamma; /* need to divide by 100 then add 1 */
} data;
} __attribute__((packed));
-#define DRM_EDID_INPUT_SERRATION_VSYNC (1 << 7)
-#define DRM_EDID_INPUT_SYNC_ON_GREEN (1 << 5)
-#define DRM_EDID_INPUT_COMPOSITE_SYNC (1 << 4)
+#define DRM_EDID_INPUT_SERRATION_VSYNC (1 << 0)
+#define DRM_EDID_INPUT_SYNC_ON_GREEN (1 << 1)
+#define DRM_EDID_INPUT_COMPOSITE_SYNC (1 << 2)
#define DRM_EDID_INPUT_SEPARATE_SYNCS (1 << 3)
-#define DRM_EDID_INPUT_BLANK_TO_BLACK (1 << 2)
-#define DRM_EDID_INPUT_VIDEO_LEVEL (3 << 1)
-#define DRM_EDID_INPUT_DIGITAL (1 << 0) /* bits above must be zero if set */
+#define DRM_EDID_INPUT_BLANK_TO_BLACK (1 << 4)
+#define DRM_EDID_INPUT_VIDEO_LEVEL (3 << 5)
+#define DRM_EDID_INPUT_DIGITAL (1 << 7) /* bits below must be zero if set */
-#define DRM_EDID_FEATURE_DEFAULT_GTF (1 << 7)
-#define DRM_EDID_FEATURE_PREFERRED_TIMING (1 << 6)
-#define DRM_EDID_FEATURE_STANDARD_COLOR (1 << 5)
+#define DRM_EDID_FEATURE_DEFAULT_GTF (1 << 0)
+#define DRM_EDID_FEATURE_PREFERRED_TIMING (1 << 1)
+#define DRM_EDID_FEATURE_STANDARD_COLOR (1 << 2)
#define DRM_EDID_FEATURE_DISPLAY_TYPE (3 << 3) /* 00=mono, 01=rgb, 10=non-rgb, 11=unknown */
-#define DRM_EDID_FEATURE_PM_ACTIVE_OFF (1 << 2)
-#define DRM_EDID_FEATURE_PM_SUSPEND (1 << 1)
-#define DRM_EDID_FEATURE_PM_STANDBY (1 << 0)
+#define DRM_EDID_FEATURE_PM_ACTIVE_OFF (1 << 5)
+#define DRM_EDID_FEATURE_PM_SUSPEND (1 << 6)
+#define DRM_EDID_FEATURE_PM_STANDBY (1 << 7)
struct edid {
u8 header[8];
#include <linux/list.h>
#include <linux/wait.h>
#include <linux/percpu.h>
+#include <linux/timer.h>
struct hrtimer_clock_base;
static inline void timer_stats_account_hrtimer(struct hrtimer *timer)
{
+ if (likely(!timer->start_pid))
+ return;
timer_stats_update_stats(timer, timer->start_pid, timer->start_site,
timer->function, timer->start_comm, 0);
}
static inline void timer_stats_hrtimer_set_start_info(struct hrtimer *timer)
{
+ if (likely(!timer_stats_active))
+ return;
__timer_stats_hrtimer_set_start_info(timer, __builtin_return_address(0));
}
#ifdef CONFIG_BLK_DEV_IDEDMA
int ide_dma_good_drive(ide_drive_t *);
int __ide_dma_bad_drive(ide_drive_t *);
-int ide_id_dma_bug(ide_drive_t *);
u8 ide_find_dma_mode(ide_drive_t *, u8);
ide_startstop_t ide_dma_timeout_retry(ide_drive_t *, int);
#else
-static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
extern void ima_file_free(struct file *file);
extern int ima_file_mmap(struct file *file, unsigned long prot);
extern void ima_counts_get(struct file *file);
+extern void ima_counts_put(struct path *path, int mask);
#else
static inline int ima_bprm_check(struct linux_binprm *bprm)
{
return;
}
+
+static inline void ima_counts_put(struct path *path, int mask)
+{
+ return;
+}
#endif /* CONFIG_IMA_H */
#endif /* _LINUX_IMA_H */
extern int panic_timeout;
extern int panic_on_oops;
extern int panic_on_unrecovered_nmi;
+extern int panic_on_io_nmi;
extern const char *print_tainted(void);
extern void add_taint(unsigned flag);
extern int test_taint(unsigned flag);
struct kvm {
struct mutex lock; /* protects the vcpus array and APIC accesses */
spinlock_t mmu_lock;
+ spinlock_t requests_lock;
struct rw_semaphore slots_lock;
struct mm_struct *mm; /* userspace tied to this vm */
int nmemslots;
--- /dev/null
+/*
+ * leds-lp3944.h - platform data structure for lp3944 led controller
+ *
+ * Copyright (C) 2009 Antonio Ospite <ospite@studenti.unina.it>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __LINUX_LEDS_LP3944_H
+#define __LINUX_LEDS_LP3944_H
+
+#include <linux/leds.h>
+#include <linux/workqueue.h>
+
+#define LP3944_LED0 0
+#define LP3944_LED1 1
+#define LP3944_LED2 2
+#define LP3944_LED3 3
+#define LP3944_LED4 4
+#define LP3944_LED5 5
+#define LP3944_LED6 6
+#define LP3944_LED7 7
+#define LP3944_LEDS_MAX 8
+
+#define LP3944_LED_STATUS_MASK 0x03
+enum lp3944_status {
+ LP3944_LED_STATUS_OFF = 0x0,
+ LP3944_LED_STATUS_ON = 0x1,
+ LP3944_LED_STATUS_DIM0 = 0x2,
+ LP3944_LED_STATUS_DIM1 = 0x3
+};
+
+enum lp3944_type {
+ LP3944_LED_TYPE_NONE,
+ LP3944_LED_TYPE_LED,
+ LP3944_LED_TYPE_LED_INVERTED,
+};
+
+struct lp3944_led {
+ char *name;
+ enum lp3944_type type;
+ enum lp3944_status status;
+};
+
+struct lp3944_platform_data {
+ struct lp3944_led leds[LP3944_LEDS_MAX];
+ u8 leds_size;
+};
+
+#endif /* __LINUX_LEDS_LP3944_H */
/* Get LED brightness level */
enum led_brightness (*brightness_get)(struct led_classdev *led_cdev);
- /* Activate hardware accelerated blink */
+ /* Activate hardware accelerated blink, delays are in
+ * miliseconds and if none is provided then a sensible default
+ * should be chosen. The call can adjust the timings if it can't
+ * match the values specified exactly. */
int (*blink_set)(struct led_classdev *led_cdev,
unsigned long *delay_on,
unsigned long *delay_off);
const char *name;
const char *default_trigger;
unsigned gpio;
- u8 active_low : 1;
- u8 retain_state_suspended : 1;
+ unsigned active_low : 1;
+ unsigned retain_state_suspended : 1;
+ unsigned default_state : 2;
+ /* default_state should be one of LEDS_GPIO_DEFSTATE_(ON|OFF|KEEP) */
};
+#define LEDS_GPIO_DEFSTATE_OFF 0
+#define LEDS_GPIO_DEFSTATE_ON 1
+#define LEDS_GPIO_DEFSTATE_KEEP 2
struct gpio_led_platform_data {
int num_leds;
extern int access_process_vm(struct task_struct *tsk, unsigned long addr, void *buf, int len, int write);
int get_user_pages(struct task_struct *tsk, struct mm_struct *mm,
- unsigned long start, int len, int write, int force,
+ unsigned long start, int nr_pages, int write, int force,
struct page **pages, struct vm_area_struct **vmas);
int get_user_pages_fast(unsigned long start, int nr_pages, int write,
struct page **pages);
*/
#ifdef CONFIG_TIMER_STATS
+extern int timer_stats_active;
+
#define TIMER_STATS_FLAG_DEFERRABLE 0x1
extern void init_timer_stats(void);
static inline void timer_stats_timer_set_start_info(struct timer_list *timer)
{
+ if (likely(!timer_stats_active))
+ return;
__timer_stats_timer_set_start_info(timer, __builtin_return_address(0));
}
int phonet_address_del(struct net_device *dev, u8 addr);
u8 phonet_address_get(struct net_device *dev, u8 addr);
int phonet_address_lookup(struct net *net, u8 addr);
+void phonet_address_notify(int event, struct net_device *dev, u8 addr);
#define PN_NO_ADDR 0xff
#include <linux/nsproxy.h>
#include <linux/pid.h>
#include <linux/ipc_namespace.h>
+#include <linux/ima.h>
#include <net/sock.h>
#include "util.h"
error = PTR_ERR(filp);
goto out_putfd;
}
+ ima_counts_get(filp);
fd_install(fd, filp);
goto out_upsem;
obj-$(CONFIG_FUNCTION_TRACER) += trace/
obj-$(CONFIG_TRACING) += trace/
obj-$(CONFIG_X86_DS) += trace/
+obj-$(CONFIG_RING_BUFFER) += trace/
obj-$(CONFIG_SMP) += sched_cpupri.o
obj-$(CONFIG_SLOW_WORK) += slow-work.o
obj-$(CONFIG_PERF_COUNTERS) += perf_counter.o
static int fault_in_user_writeable(u32 __user *uaddr)
{
int ret = get_user_pages(current, current->mm, (unsigned long)uaddr,
- sizeof(*uaddr), 1, 0, NULL, NULL);
+ 1, 1, 0, NULL, NULL);
return ret < 0 ? ret : 0;
}
.data = &sysctl_timer_migration,
.maxlen = sizeof(unsigned int),
.mode = 0644,
- .proc_handler = &proc_dointvec,
+ .proc_handler = &proc_dointvec_minmax,
+ .strategy = &sysctl_intvec,
+ .extra1 = &zero,
+ .extra2 = &one,
},
#endif
{
.mode = 0644,
.proc_handler = &proc_dointvec,
},
+ {
+ .ctl_name = CTL_UNNUMBERED,
+ .procname = "panic_on_io_nmi",
+ .data = &panic_on_io_nmi,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = &proc_dointvec,
+ },
{
.ctl_name = KERN_BOOTLOADER_TYPE,
.procname = "bootloader_type",
/*
* Collection status, active/inactive:
*/
-static int __read_mostly active;
+int __read_mostly timer_stats_active;
/*
* Beginning/end timestamps of measurement:
struct entry *entry, input;
unsigned long flags;
- if (likely(!active))
+ if (likely(!timer_stats_active))
return;
lock = &per_cpu(lookup_lock, raw_smp_processor_id());
input.timer_flag = timer_flag;
spin_lock_irqsave(lock, flags);
- if (!active)
+ if (!timer_stats_active)
goto out_unlock;
entry = tstat_lookup(&input, comm);
/*
* If still active then calculate up to now:
*/
- if (active)
+ if (timer_stats_active)
time_stop = ktime_get();
time = ktime_sub(time_stop, time_start);
mutex_lock(&show_mutex);
switch (ctl[0]) {
case '0':
- if (active) {
- active = 0;
+ if (timer_stats_active) {
+ timer_stats_active = 0;
time_stop = ktime_get();
sync_access();
}
break;
case '1':
- if (!active) {
+ if (!timer_stats_active) {
reset_entries();
time_start = ktime_get();
smp_mb();
- active = 1;
+ timer_stats_active = 1;
}
break;
default:
{
unsigned int flag = 0;
+ if (likely(!timer->start_site))
+ return;
if (unlikely(tbase_get_deferrable(timer->base)))
flag |= TIMER_STATS_FLAG_DEFERRABLE;
pg = (struct ftrace_profile_page *)((unsigned long)rec & PAGE_MASK);
again:
- rec++;
+ if (idx != 0)
+ rec++;
+
if ((void *)rec >= (void *)&pg->records[pg->index]) {
pg = pg->next;
if (!pg)
{
struct ftrace_iterator *iter = m->private;
void *p = NULL;
+ loff_t l;
+
+ if (!(iter->flags & FTRACE_ITER_HASH))
+ *pos = 0;
iter->flags |= FTRACE_ITER_HASH;
- return t_hash_next(m, p, pos);
+ iter->hidx = 0;
+ for (l = 0; l <= *pos; ) {
+ p = t_hash_next(m, p, &l);
+ if (!p)
+ break;
+ }
+ return p;
}
static int t_hash_show(struct seq_file *m, void *v)
iter->pg = iter->pg->next;
iter->idx = 0;
goto retry;
- } else {
- iter->idx = -1;
}
} else {
rec = &iter->pg->records[iter->idx++];
{
struct ftrace_iterator *iter = m->private;
void *p = NULL;
+ loff_t l;
mutex_lock(&ftrace_lock);
/*
if (*pos > 0)
return t_hash_start(m, pos);
iter->flags |= FTRACE_ITER_PRINTALL;
- (*pos)++;
return iter;
}
if (iter->flags & FTRACE_ITER_HASH)
return t_hash_start(m, pos);
- if (*pos > 0) {
- if (iter->idx < 0)
- return p;
- (*pos)--;
- iter->idx--;
+ iter->pg = ftrace_pages_start;
+ iter->idx = 0;
+ for (l = 0; l <= *pos; ) {
+ p = t_next(m, p, &l);
+ if (!p)
+ break;
}
- p = t_next(m, p, pos);
-
- if (!p)
+ if (!p && iter->flags & FTRACE_ITER_FILTER)
return t_hash_start(m, pos);
return p;
unsigned long ftrace_graph_funcs[FTRACE_GRAPH_MAX_FUNCS] __read_mostly;
static void *
-g_next(struct seq_file *m, void *v, loff_t *pos)
+__g_next(struct seq_file *m, loff_t *pos)
{
unsigned long *array = m->private;
- int index = *pos;
- (*pos)++;
-
- if (index >= ftrace_graph_count)
+ if (*pos >= ftrace_graph_count)
return NULL;
+ return &array[*pos];
+}
- return &array[index];
+static void *
+g_next(struct seq_file *m, void *v, loff_t *pos)
+{
+ (*pos)++;
+ return __g_next(m, pos);
}
static void *g_start(struct seq_file *m, loff_t *pos)
{
- void *p = NULL;
-
mutex_lock(&graph_lock);
/* Nothing, tell g_show to print all functions are enabled */
if (!ftrace_graph_count && !*pos)
return (void *)1;
- p = g_next(m, p, pos);
-
- return p;
+ return __g_next(m, pos);
}
static void g_stop(struct seq_file *m, void *p)
return NULL;
}
+#ifdef CONFIG_TRACING
+
#define TRACE_RECURSIVE_DEPTH 16
static int trace_recursive_lock(void)
current->trace_recursion--;
}
+#else
+
+#define trace_recursive_lock() (0)
+#define trace_recursive_unlock() do { } while (0)
+
+#endif
+
static DEFINE_PER_CPU(int, rb_need_resched);
/**
}
EXPORT_SYMBOL_GPL(ring_buffer_read_page);
+#ifdef CONFIG_TRACING
static ssize_t
rb_simple_read(struct file *filp, char __user *ubuf,
size_t cnt, loff_t *ppos)
}
fs_initcall(rb_init_debugfs);
+#endif
#ifdef CONFIG_HOTPLUG_CPU
static int rb_cpu_notify(struct notifier_block *self,
static int __init set_buf_size(char *str)
{
unsigned long buf_size;
- int ret;
if (!str)
return 0;
- ret = strict_strtoul(str, 0, &buf_size);
+ buf_size = memparse(str, &str);
/* nr_entries can not be zero */
- if (ret < 0 || buf_size == 0)
+ if (buf_size == 0)
return 0;
trace_buf_size = buf_size;
return 1;
static void *
t_next(struct seq_file *m, void *v, loff_t *pos)
{
- struct tracer *t = m->private;
+ struct tracer *t = v;
(*pos)++;
if (t)
t = t->next;
- m->private = t;
-
return t;
}
static void *t_start(struct seq_file *m, loff_t *pos)
{
- struct tracer *t = m->private;
+ struct tracer *t;
loff_t l = 0;
mutex_lock(&trace_types_lock);
- for (; t && l < *pos; t = t_next(m, t, &l))
+ for (t = trace_types; t && l < *pos; t = t_next(m, t, &l))
;
return t;
static int show_traces_open(struct inode *inode, struct file *file)
{
- int ret;
-
if (tracing_disabled)
return -ENODEV;
- ret = seq_open(file, &show_traces_seq_ops);
- if (!ret) {
- struct seq_file *m = file->private_data;
- m->private = trace_types;
- }
-
- return ret;
+ return seq_open(file, &show_traces_seq_ops);
}
static ssize_t
extern struct pid *ftrace_pid_trace;
+#ifdef CONFIG_FUNCTION_TRACER
static inline int ftrace_trace_task(struct task_struct *task)
{
if (!ftrace_pid_trace)
return test_tsk_trace_trace(task);
}
+#else
+static inline int ftrace_trace_task(struct task_struct *task)
+{
+ return 1;
+}
+#endif
/*
* trace_iterator_flags is an enumeration that defines bit
static void *t_start(struct seq_file *m, loff_t *pos)
{
+ struct ftrace_event_call *call = NULL;
+ loff_t l;
+
mutex_lock(&event_mutex);
- if (*pos == 0)
- m->private = ftrace_events.next;
- return t_next(m, NULL, pos);
+
+ m->private = ftrace_events.next;
+ for (l = 0; l <= *pos; ) {
+ call = t_next(m, NULL, &l);
+ if (!call)
+ break;
+ }
+ return call;
}
static void *
static void *s_start(struct seq_file *m, loff_t *pos)
{
+ struct ftrace_event_call *call = NULL;
+ loff_t l;
+
mutex_lock(&event_mutex);
- if (*pos == 0)
- m->private = ftrace_events.next;
- return s_next(m, NULL, pos);
+
+ m->private = ftrace_events.next;
+ for (l = 0; l <= *pos; ) {
+ call = s_next(m, NULL, &l);
+ if (!call)
+ break;
+ }
+ return call;
}
static int t_show(struct seq_file *m, void *v)
if (count == -1)
seq_printf(m, ":unlimited\n");
else
- seq_printf(m, ":count=%ld", count);
- seq_putc(m, '\n');
+ seq_printf(m, ":count=%ld\n", count);
return 0;
}
EXPORT_SYMBOL_GPL(__ftrace_vprintk);
static void *
-t_next(struct seq_file *m, void *v, loff_t *pos)
+t_start(struct seq_file *m, loff_t *pos)
{
- const char **fmt = m->private;
- const char **next = fmt;
-
- (*pos)++;
+ const char **fmt = __start___trace_bprintk_fmt + *pos;
if ((unsigned long)fmt >= (unsigned long)__stop___trace_bprintk_fmt)
return NULL;
-
- next = fmt;
- m->private = ++next;
-
return fmt;
}
-static void *t_start(struct seq_file *m, loff_t *pos)
+static void *t_next(struct seq_file *m, void * v, loff_t *pos)
{
- return t_next(m, NULL, pos);
+ (*pos)++;
+ return t_start(m, pos);
}
static int t_show(struct seq_file *m, void *v)
static int
ftrace_formats_open(struct inode *inode, struct file *file)
{
- int ret;
-
- ret = seq_open(file, &show_format_seq_ops);
- if (!ret) {
- struct seq_file *m = file->private_data;
-
- m->private = __start___trace_bprintk_fmt;
- }
- return ret;
+ return seq_open(file, &show_format_seq_ops);
}
static const struct file_operations ftrace_formats_fops = {
mutex_lock(&session->stat_mutex);
/* If we are in the beginning of the file, print the headers */
- if (!*pos && session->ts->stat_headers) {
- (*pos)++;
+ if (!*pos && session->ts->stat_headers)
return SEQ_START_TOKEN;
- }
node = rb_first(&session->stat_root);
for (i = 0; node && i < *pos; i++)
node = rb_next(node);
- (*pos)++;
-
return node;
}
int __get_user_pages(struct task_struct *tsk, struct mm_struct *mm,
- unsigned long start, int len, int flags,
- struct page **pages, struct vm_area_struct **vmas)
+ unsigned long start, int nr_pages, int flags,
+ struct page **pages, struct vm_area_struct **vmas)
{
int i;
unsigned int vm_flags = 0;
int ignore = !!(flags & GUP_FLAGS_IGNORE_VMA_PERMISSIONS);
int ignore_sigkill = !!(flags & GUP_FLAGS_IGNORE_SIGKILL);
- if (len <= 0)
+ if (nr_pages <= 0)
return 0;
/*
* Require read or write permissions.
vmas[i] = gate_vma;
i++;
start += PAGE_SIZE;
- len--;
+ nr_pages--;
continue;
}
if (is_vm_hugetlb_page(vma)) {
i = follow_hugetlb_page(mm, vma, pages, vmas,
- &start, &len, i, write);
+ &start, &nr_pages, i, write);
continue;
}
vmas[i] = vma;
i++;
start += PAGE_SIZE;
- len--;
- } while (len && start < vma->vm_end);
- } while (len);
+ nr_pages--;
+ } while (nr_pages && start < vma->vm_end);
+ } while (nr_pages);
return i;
}
* @tsk: task_struct of target task
* @mm: mm_struct of target mm
* @start: starting user address
- * @len: number of pages from start to pin
+ * @nr_pages: number of pages from start to pin
* @write: whether pages will be written to by the caller
* @force: whether to force write access even if user mapping is
* readonly. This will result in the page being COWed even
* Or NULL if the caller does not require them.
*
* Returns number of pages pinned. This may be fewer than the number
- * requested. If len is 0 or negative, returns 0. If no pages
+ * requested. If nr_pages is 0 or negative, returns 0. If no pages
* were pinned, returns -errno. Each page returned must be released
* with a put_page() call when it is finished with. vmas will only
* remain valid while mmap_sem is held.
* See also get_user_pages_fast, for performance critical applications.
*/
int get_user_pages(struct task_struct *tsk, struct mm_struct *mm,
- unsigned long start, int len, int write, int force,
+ unsigned long start, int nr_pages, int write, int force,
struct page **pages, struct vm_area_struct **vmas)
{
int flags = 0;
if (force)
flags |= GUP_FLAGS_FORCE;
- return __get_user_pages(tsk, mm,
- start, len, flags,
- pages, vmas);
+ return __get_user_pages(tsk, mm, start, nr_pages, flags, pages, vmas);
}
EXPORT_SYMBOL(get_user_pages);
}
int __get_user_pages(struct task_struct *tsk, struct mm_struct *mm,
- unsigned long start, int len, int flags,
- struct page **pages, struct vm_area_struct **vmas)
+ unsigned long start, int nr_pages, int flags,
+ struct page **pages, struct vm_area_struct **vmas)
{
struct vm_area_struct *vma;
unsigned long vm_flags;
vm_flags = write ? (VM_WRITE | VM_MAYWRITE) : (VM_READ | VM_MAYREAD);
vm_flags &= force ? (VM_MAYREAD | VM_MAYWRITE) : (VM_READ | VM_WRITE);
- for (i = 0; i < len; i++) {
+ for (i = 0; i < nr_pages; i++) {
vma = find_vma(mm, start);
if (!vma)
goto finish_or_fault;
* - don't permit access to VMAs that don't support it, such as I/O mappings
*/
int get_user_pages(struct task_struct *tsk, struct mm_struct *mm,
- unsigned long start, int len, int write, int force,
+ unsigned long start, int nr_pages, int write, int force,
struct page **pages, struct vm_area_struct **vmas)
{
int flags = 0;
if (force)
flags |= GUP_FLAGS_FORCE;
- return __get_user_pages(tsk, mm,
- start, len, flags,
- pages, vmas);
+ return __get_user_pages(tsk, mm, start, nr_pages, flags, pages, vmas);
}
EXPORT_SYMBOL(get_user_pages);
* @chunk: chunk of interest
* @page_start: page index of the first page to unmap
* @page_end: page index of the last page to unmap + 1
- * @flush: whether to flush cache and tlb or not
+ * @flush_tlb: whether to flush tlb or not
*
* For each cpu, unmap pages [@page_start,@page_end) out of @chunk.
* If @flush is true, vcache is flushed before unmapping and tlb
* after.
*/
static void pcpu_unmap(struct pcpu_chunk *chunk, int page_start, int page_end,
- bool flush)
+ bool flush_tlb)
{
unsigned int last = num_possible_cpus() - 1;
unsigned int cpu;
* the whole region at once rather than doing it for each cpu.
* This could be an overkill but is more scalable.
*/
- if (flush)
- flush_cache_vunmap(pcpu_chunk_addr(chunk, 0, page_start),
- pcpu_chunk_addr(chunk, last, page_end));
+ flush_cache_vunmap(pcpu_chunk_addr(chunk, 0, page_start),
+ pcpu_chunk_addr(chunk, last, page_end));
for_each_possible_cpu(cpu)
unmap_kernel_range_noflush(
(page_end - page_start) << PAGE_SHIFT);
/* ditto as flush_cache_vunmap() */
- if (flush)
+ if (flush_tlb)
flush_tlb_kernel_range(pcpu_chunk_addr(chunk, 0, page_start),
pcpu_chunk_addr(chunk, last, page_end));
}
ssize_t __init pcpu_embed_first_chunk(size_t static_size, size_t reserved_size,
ssize_t dyn_size, ssize_t unit_size)
{
+ size_t chunk_size;
unsigned int cpu;
/* determine parameters and allocate */
} else
pcpue_unit_size = max_t(size_t, pcpue_size, PCPU_MIN_UNIT_SIZE);
- pcpue_ptr = __alloc_bootmem_nopanic(
- num_possible_cpus() * pcpue_unit_size,
- PAGE_SIZE, __pa(MAX_DMA_ADDRESS));
- if (!pcpue_ptr)
+ chunk_size = pcpue_unit_size * num_possible_cpus();
+
+ pcpue_ptr = __alloc_bootmem_nopanic(chunk_size, PAGE_SIZE,
+ __pa(MAX_DMA_ADDRESS));
+ if (!pcpue_ptr) {
+ pr_warning("PERCPU: failed to allocate %zu bytes for "
+ "embedding\n", chunk_size);
return -ENOMEM;
+ }
/* return the leftover and copy */
for_each_possible_cpu(cpu) {
unregister_pernet_subsys(&br_net_ops);
- synchronize_net();
+ rcu_barrier(); /* Wait for completion of call_rcu()'s */
br_netfilter_fini();
#if defined(CONFIG_ATM_LANE) || defined(CONFIG_ATM_LANE_MODULE)
* move the instance around on the list at-will.
*/
if (unlikely(work == weight)) {
- if (unlikely(napi_disable_pending(n)))
- __napi_complete(n);
- else
+ if (unlikely(napi_disable_pending(n))) {
+ local_irq_enable();
+ napi_complete(n);
+ local_irq_disable();
+ } else
list_move_tail(&n->poll_list, list);
}
proc_net_remove(&init_net, "decnet");
proto_unregister(&dn_proto);
+
+ rcu_barrier_bh(); /* Wait for completion of call_rcu_bh()'s */
}
module_exit(decnet_exit);
#endif
/* Remove any debris in the socket control block */
memset(IPCB(skb), 0, sizeof(struct inet_skb_parm));
+ /* Must drop socket now because of tproxy. */
+ skb_orphan(skb);
+
return NF_HOOK(PF_INET, NF_INET_PRE_ROUTING, skb, dev, NULL,
ip_rcv_finish);
goto kill_with_rst;
/* Dup ACK? */
- if (!after(TCP_SKB_CB(skb)->end_seq, tcptw->tw_rcv_nxt) ||
+ if (!th->ack ||
+ !after(TCP_SKB_CB(skb)->end_seq, tcptw->tw_rcv_nxt) ||
TCP_SKB_CB(skb)->end_seq == TCP_SKB_CB(skb)->seq) {
inet_twsk_put(tw);
return TCP_TW_SUCCESS;
valid = ifa->valid_lft;
if (preferred != INFINITY_LIFE_TIME) {
long tval = (jiffies - ifa->tstamp)/HZ;
- preferred -= tval;
+ if (preferred > tval)
+ preferred -= tval;
+ else
+ preferred = 0;
if (valid != INFINITY_LIFE_TIME)
valid -= tval;
}
proto_unregister(&udplitev6_prot);
proto_unregister(&udpv6_prot);
proto_unregister(&tcpv6_prot);
+
+ rcu_barrier(); /* Wait for completion of call_rcu()'s */
}
module_exit(inet6_exit);
rcu_read_unlock();
+ /* Must drop socket now because of tproxy. */
+ skb_orphan(skb);
+
return NF_HOOK(PF_INET6, NF_INET_PRE_ROUTING, skb, dev, NULL,
ip6_rcv_finish);
err:
* should it be using the interface and enqueuing
* frames at this very time on another CPU.
*/
- synchronize_rcu();
+ rcu_barrier(); /* Wait for RX path and call_rcu()'s */
skb_queue_purge(&sdata->u.mesh.skb_queue);
}
return NULL;
}
-static void __phonet_device_free(struct phonet_device *pnd)
+static void phonet_device_destroy(struct net_device *dev)
{
- list_del(&pnd->list);
- kfree(pnd);
+ struct phonet_device_list *pndevs = phonet_device_list(dev_net(dev));
+ struct phonet_device *pnd;
+
+ ASSERT_RTNL();
+
+ spin_lock_bh(&pndevs->lock);
+ pnd = __phonet_get(dev);
+ if (pnd)
+ list_del(&pnd->list);
+ spin_unlock_bh(&pndevs->lock);
+
+ if (pnd) {
+ u8 addr;
+
+ for (addr = find_first_bit(pnd->addrs, 64); addr < 64;
+ addr = find_next_bit(pnd->addrs, 64, 1+addr))
+ phonet_address_notify(RTM_DELADDR, dev, addr);
+ kfree(pnd);
+ }
}
struct net_device *phonet_device_get(struct net *net)
pnd = __phonet_get(dev);
if (!pnd || !test_and_clear_bit(addr >> 2, pnd->addrs))
err = -EADDRNOTAVAIL;
- else if (bitmap_empty(pnd->addrs, 64))
- __phonet_device_free(pnd);
+ else if (bitmap_empty(pnd->addrs, 64)) {
+ list_del(&pnd->list);
+ kfree(pnd);
+ }
spin_unlock_bh(&pndevs->lock);
return err;
}
{
struct net_device *dev = arg;
- if (what == NETDEV_UNREGISTER) {
- struct phonet_device_list *pndevs;
- struct phonet_device *pnd;
-
- /* Destroy phonet-specific device data */
- pndevs = phonet_device_list(dev_net(dev));
- spin_lock_bh(&pndevs->lock);
- pnd = __phonet_get(dev);
- if (pnd)
- __phonet_device_free(pnd);
- spin_unlock_bh(&pndevs->lock);
- }
+ if (what == NETDEV_UNREGISTER)
+ phonet_device_destroy(dev);
return 0;
}
static void phonet_exit_net(struct net *net)
{
struct phonet_net *pnn = net_generic(net, phonet_net_id);
- struct phonet_device *pnd, *n;
-
- list_for_each_entry_safe(pnd, n, &pnn->pndevs.list, list)
- __phonet_device_free(pnd);
+ struct net_device *dev;
+ rtnl_lock();
+ for_each_netdev(net, dev)
+ phonet_device_destroy(dev);
+ rtnl_unlock();
kfree(pnn);
}
static int fill_addr(struct sk_buff *skb, struct net_device *dev, u8 addr,
u32 pid, u32 seq, int event);
-static void rtmsg_notify(int event, struct net_device *dev, u8 addr)
+void phonet_address_notify(int event, struct net_device *dev, u8 addr)
{
struct sk_buff *skb;
int err = -ENOBUFS;
else
err = phonet_address_del(dev, pnaddr);
if (!err)
- rtmsg_notify(nlh->nlmsg_type, dev, pnaddr);
+ phonet_address_notify(nlh->nlmsg_type, dev, pnaddr);
return err;
}
#ifdef CONFIG_PROC_FS
rpc_proc_exit();
#endif
+ rcu_barrier(); /* Wait for completion of call_rcu()'s */
}
MODULE_LICENSE("GPL");
module_init(init_sunrpc);
}
},
{
- .name = "cbc(cast128)",
- .compat = "cast128",
+ .name = "cbc(cast5)",
+ .compat = "cast5",
.uinfo = {
.encr = {
--- /dev/null
+dtc
+dtc-lexer.lex.c
+dtc-parser.tab.c
+dtc-parser.tab.h
+
}
/*
- * ima_opens_get - increment file counts
+ * ima_counts_put - decrement file counts
+ *
+ * File counts are incremented in ima_path_check. On file open
+ * error, such as ETXTBSY, decrement the counts to prevent
+ * unnecessary imbalance messages.
+ */
+void ima_counts_put(struct path *path, int mask)
+{
+ struct inode *inode = path->dentry->d_inode;
+ struct ima_iint_cache *iint;
+
+ if (!ima_initialized || !S_ISREG(inode->i_mode))
+ return;
+ iint = ima_iint_find_insert_get(inode);
+ if (!iint)
+ return;
+
+ mutex_lock(&iint->mutex);
+ iint->opencount--;
+ if ((mask & MAY_WRITE) || (mask == 0))
+ iint->writecount--;
+ else if (mask & (MAY_READ | MAY_EXEC))
+ iint->readcount--;
+ mutex_unlock(&iint->mutex);
+}
+
+/*
+ * ima_counts_get - increment file counts
*
* - for IPC shm and shmat file.
* - for nfsd exported files.
}
out:
mutex_unlock(&ima_extend_list_mutex);
- integrity_audit_msg(AUDIT_INTEGRITY_PCR, inode, entry->template_name,
+ integrity_audit_msg(AUDIT_INTEGRITY_PCR, inode,
+ entry->template.file_name,
op, audit_cause, result, audit_info);
return result;
}
cpumask_clear(cpus);
me = get_cpu();
+ spin_lock(&kvm->requests_lock);
for (i = 0; i < KVM_MAX_VCPUS; ++i) {
vcpu = kvm->vcpus[i];
if (!vcpu)
smp_call_function_many(cpus, ack_flush, NULL, 1);
else
called = false;
+ spin_unlock(&kvm->requests_lock);
put_cpu();
free_cpumask_var(cpus);
return called;
kvm->mm = current->mm;
atomic_inc(&kvm->mm->mm_count);
spin_lock_init(&kvm->mmu_lock);
+ spin_lock_init(&kvm->requests_lock);
kvm_io_bus_init(&kvm->pio_bus);
mutex_init(&kvm->lock);
kvm_io_bus_init(&kvm->mmio_bus);
if (!new.dirty_bitmap)
goto out_free;
memset(new.dirty_bitmap, 0, dirty_bytes);
+ if (old.npages)
+ kvm_arch_flush_shadow(kvm);
}
#endif /* not defined CONFIG_S390 */
projects / karo-tx-linux.git / commitdiff