note of cpu#.
crash_notes_size: size of the note of cpu#.
+
+
+What: /sys/devices/system/cpu/intel_pstate/max_perf_pct
+ /sys/devices/system/cpu/intel_pstate/min_perf_pct
+ /sys/devices/system/cpu/intel_pstate/no_turbo
+Date: February 2013
+Contact: linux-pm@vger.kernel.org
+Description: Parameters for the Intel P-state driver
+
+ Logic for selecting the current P-state in Intel
+ Sandybridge+ processors. The three knobs control
+ limits for the P-state that will be requested by the
+ driver.
+
+ max_perf_pct: limits the maximum P state that will be requested by
+ the driver stated as a percentage of the available performance.
+
+ min_perf_pct: limits the minimum P state that will be requested by
+ the driver stated as a percentage of the available performance.
+
+ no_turbo: limits the driver to selecting P states below the turbo
+ frequency range.
+
+ More details can be found in Documentation/cpu-freq/intel-pstate.txt
--- /dev/null
+Intel P-state driver
+--------------------
+
+This driver implements a scaling driver with an internal governor for
+Intel Core processors. The driver follows the same model as the
+Transmeta scaling driver (longrun.c) and implements the setpolicy()
+instead of target(). Scaling drivers that implement setpolicy() are
+assumed to implement internal governors by the cpufreq core. All the
+logic for selecting the current P state is contained within the
+driver; no external governor is used by the cpufreq core.
+
+Intel SandyBridge+ processors are supported.
+
+New sysfs files for controlling P state selection have been added to
+/sys/devices/system/cpu/intel_pstate/
+
+ max_perf_pct: limits the maximum P state that will be requested by
+ the driver stated as a percentage of the available performance.
+
+ min_perf_pct: limits the minimum P state that will be requested by
+ the driver stated as a percentage of the available performance.
+
+ no_turbo: limits the driver to selecting P states below the turbo
+ frequency range.
+
+For contemporary Intel processors, the frequency is controlled by the
+processor itself and the P-states exposed to software are related to
+performance levels. The idea that frequency can be set to a single
+frequency is fiction for Intel Core processors. Even if the scaling
+driver selects a single P state the actual frequency the processor
+will run at is selected by the processor itself.
+
+New debugfs files have also been added to /sys/kernel/debug/pstate_snb/
+
+ deadband
+ d_gain_pct
+ i_gain_pct
+ p_gain_pct
+ sample_rate_ms
+ setpoint
platform_device_register(&exynos_cpuidle);
}
+void __init exynos_cpufreq_init(void)
+{
+ platform_device_register_simple("exynos-cpufreq", -1, NULL, 0);
+}
+
void __init exynos_init_late(void)
{
if (of_machine_is_compatible("samsung,exynos5440"))
void exynos4_restart(enum reboot_mode mode, const char *cmd);
void exynos5_restart(enum reboot_mode mode, const char *cmd);
void exynos_cpuidle_init(void);
+void exynos_cpufreq_init(void);
void exynos_init_late(void);
void exynos_firmware_init(void);
static void __init exynos4_dt_machine_init(void)
{
exynos_cpuidle_init();
+ exynos_cpufreq_init();
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
}
exynos_cpuidle_init();
+ exynos_cpufreq_init();
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
static DEFINE_SPINLOCK(clocks_lock);
+/* Dummy clk routine to build generic kernel parts that may be using them */
+unsigned long clk_get_rate(struct clk *clk)
+{
+ return 0;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
static void clk_gpio27_enable(struct clk *clk)
{
/*
config GENERIC_CPUFREQ_CPU0
tristate "Generic CPU0 cpufreq driver"
- depends on HAVE_CLK && REGULATOR && PM_OPP && OF
+ depends on HAVE_CLK && REGULATOR && OF
+ select PM_OPP
help
This adds a generic cpufreq driver for CPU0 frequency management.
It supports both uniprocessor (UP) and symmetric multiprocessor (SMP)
config ARM_BIG_LITTLE_CPUFREQ
tristate "Generic ARM big LITTLE CPUfreq driver"
- depends on ARM_CPU_TOPOLOGY && PM_OPP && HAVE_CLK
+ depends on ARM && BIG_LITTLE && ARM_CPU_TOPOLOGY && HAVE_CLK
+ select PM_OPP
help
This enables the Generic CPUfreq driver for ARM big.LITTLE platforms.
config ARM_EXYNOS5440_CPUFREQ
bool "SAMSUNG EXYNOS5440"
depends on SOC_EXYNOS5440
- depends on HAVE_CLK && PM_OPP && OF
+ depends on HAVE_CLK && OF
+ select PM_OPP
default y
help
This adds the CPUFreq driver for Samsung EXYNOS5440
If in doubt, say N.
config ARM_IMX6Q_CPUFREQ
- tristate "Freescale i.MX6Q cpufreq support"
- depends on SOC_IMX6Q
+ tristate "Freescale i.MX6 cpufreq support"
+ depends on ARCH_MXC
depends on REGULATOR_ANATOP
help
- This adds cpufreq driver support for Freescale i.MX6Q SOC.
+ This adds cpufreq driver support for Freescale i.MX6 series SoCs.
If in doubt, say N.
static struct cpufreq_driver bL_cpufreq_driver = {
.name = "arm-big-little",
.flags = CPUFREQ_STICKY |
- CPUFREQ_HAVE_GOVERNOR_PER_POLICY,
+ CPUFREQ_HAVE_GOVERNOR_PER_POLICY |
+ CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = bL_cpufreq_set_target,
.get = bL_cpufreq_get_rate,
#include <linux/export.h>
#include <linux/slab.h>
-static struct clk *cpuclk;
static struct cpufreq_frequency_table *freq_table;
-static unsigned int at32_get_speed(unsigned int cpu)
-{
- /* No SMP support */
- if (cpu)
- return 0;
- return (unsigned int)((clk_get_rate(cpuclk) + 500) / 1000);
-}
-
static unsigned int ref_freq;
static unsigned long loops_per_jiffy_ref;
{
unsigned int old_freq, new_freq;
- old_freq = at32_get_speed(0);
+ old_freq = policy->cur;
new_freq = freq_table[index].frequency;
if (!ref_freq) {
if (old_freq < new_freq)
boot_cpu_data.loops_per_jiffy = cpufreq_scale(
loops_per_jiffy_ref, ref_freq, new_freq);
- clk_set_rate(cpuclk, new_freq * 1000);
+ clk_set_rate(policy->clk, new_freq * 1000);
if (new_freq < old_freq)
boot_cpu_data.loops_per_jiffy = cpufreq_scale(
loops_per_jiffy_ref, ref_freq, new_freq);
static int at32_cpufreq_driver_init(struct cpufreq_policy *policy)
{
unsigned int frequency, rate, min_freq;
+ static struct clk *cpuclk;
int retval, steps, i;
if (policy->cpu != 0)
frequency /= 2;
}
+ policy->clk = cpuclk;
freq_table[steps - 1].frequency = CPUFREQ_TABLE_END;
retval = cpufreq_table_validate_and_show(policy, freq_table);
.init = at32_cpufreq_driver_init,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = at32_set_target,
- .get = at32_get_speed,
+ .get = cpufreq_generic_get,
.flags = CPUFREQ_STICKY,
};
static struct regulator *cpu_reg;
static struct cpufreq_frequency_table *freq_table;
-static unsigned int cpu0_get_speed(unsigned int cpu)
-{
- return clk_get_rate(cpu_clk) / 1000;
-}
-
static int cpu0_set_target(struct cpufreq_policy *policy, unsigned int index)
{
struct dev_pm_opp *opp;
int ret;
freq_Hz = clk_round_rate(cpu_clk, freq_table[index].frequency * 1000);
- if (freq_Hz < 0)
+ if (freq_Hz <= 0)
freq_Hz = freq_table[index].frequency * 1000;
freq_exact = freq_Hz;
static int cpu0_cpufreq_init(struct cpufreq_policy *policy)
{
+ policy->clk = cpu_clk;
return cpufreq_generic_init(policy, freq_table, transition_latency);
}
.flags = CPUFREQ_STICKY,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = cpu0_set_target,
- .get = cpu0_get_speed,
+ .get = cpufreq_generic_get,
.init = cpu0_cpufreq_init,
.exit = cpufreq_generic_exit,
.name = "generic_cpu0",
static DEFINE_PER_CPU(struct cpufreq_policy *, cpufreq_cpu_data);
static DEFINE_PER_CPU(struct cpufreq_policy *, cpufreq_cpu_data_fallback);
static DEFINE_RWLOCK(cpufreq_driver_lock);
-static DEFINE_MUTEX(cpufreq_governor_lock);
+DEFINE_MUTEX(cpufreq_governor_lock);
static LIST_HEAD(cpufreq_policy_list);
#ifdef CONFIG_HOTPLUG_CPU
}
EXPORT_SYMBOL_GPL(cpufreq_generic_init);
+unsigned int cpufreq_generic_get(unsigned int cpu)
+{
+ struct cpufreq_policy *policy = per_cpu(cpufreq_cpu_data, cpu);
+
+ if (!policy || IS_ERR(policy->clk)) {
+ pr_err("%s: No %s associated to cpu: %d\n", __func__,
+ policy ? "clk" : "policy", cpu);
+ return 0;
+ }
+
+ return clk_get_rate(policy->clk) / 1000;
+}
+EXPORT_SYMBOL_GPL(cpufreq_generic_get);
+
struct cpufreq_policy *cpufreq_cpu_get(unsigned int cpu)
{
struct cpufreq_policy *policy = NULL;
}
EXPORT_SYMBOL_GPL(cpufreq_notify_transition);
+/* Do post notifications when there are chances that transition has failed */
+void cpufreq_notify_post_transition(struct cpufreq_policy *policy,
+ struct cpufreq_freqs *freqs, int transition_failed)
+{
+ cpufreq_notify_transition(policy, freqs, CPUFREQ_POSTCHANGE);
+ if (!transition_failed)
+ return;
+
+ swap(freqs->old, freqs->new);
+ cpufreq_notify_transition(policy, freqs, CPUFREQ_PRECHANGE);
+ cpufreq_notify_transition(policy, freqs, CPUFREQ_POSTCHANGE);
+}
+EXPORT_SYMBOL_GPL(cpufreq_notify_post_transition);
+
/*********************************************************************
* SYSFS INTERFACE *
struct kobject *kobj;
struct completion *cmp;
+ blocking_notifier_call_chain(&cpufreq_policy_notifier_list,
+ CPUFREQ_REMOVE_POLICY, policy);
+
down_read(&policy->rwsem);
kobj = &policy->kobj;
cmp = &policy->kobj_unregister;
goto err_set_policy_cpu;
}
+ write_lock_irqsave(&cpufreq_driver_lock, flags);
+ for_each_cpu(j, policy->cpus)
+ per_cpu(cpufreq_cpu_data, j) = policy;
+ write_unlock_irqrestore(&cpufreq_driver_lock, flags);
+
if (cpufreq_driver->get) {
policy->cur = cpufreq_driver->get(policy->cpu);
if (!policy->cur) {
}
}
+ /*
+ * Sometimes boot loaders set CPU frequency to a value outside of
+ * frequency table present with cpufreq core. In such cases CPU might be
+ * unstable if it has to run on that frequency for long duration of time
+ * and so its better to set it to a frequency which is specified in
+ * freq-table. This also makes cpufreq stats inconsistent as
+ * cpufreq-stats would fail to register because current frequency of CPU
+ * isn't found in freq-table.
+ *
+ * Because we don't want this change to effect boot process badly, we go
+ * for the next freq which is >= policy->cur ('cur' must be set by now,
+ * otherwise we will end up setting freq to lowest of the table as 'cur'
+ * is initialized to zero).
+ *
+ * We are passing target-freq as "policy->cur - 1" otherwise
+ * __cpufreq_driver_target() would simply fail, as policy->cur will be
+ * equal to target-freq.
+ */
+ if ((cpufreq_driver->flags & CPUFREQ_NEED_INITIAL_FREQ_CHECK)
+ && has_target()) {
+ /* Are we running at unknown frequency ? */
+ ret = cpufreq_frequency_table_get_index(policy, policy->cur);
+ if (ret == -EINVAL) {
+ /* Warn user and fix it */
+ pr_warn("%s: CPU%d: Running at unlisted freq: %u KHz\n",
+ __func__, policy->cpu, policy->cur);
+ ret = __cpufreq_driver_target(policy, policy->cur - 1,
+ CPUFREQ_RELATION_L);
+
+ /*
+ * Reaching here after boot in a few seconds may not
+ * mean that system will remain stable at "unknown"
+ * frequency for longer duration. Hence, a BUG_ON().
+ */
+ BUG_ON(ret);
+ pr_warn("%s: CPU%d: Unlisted initial frequency changed to: %u KHz\n",
+ __func__, policy->cpu, policy->cur);
+ }
+ }
+
/* related cpus should atleast have policy->cpus */
cpumask_or(policy->related_cpus, policy->related_cpus, policy->cpus);
}
#endif
- write_lock_irqsave(&cpufreq_driver_lock, flags);
- for_each_cpu(j, policy->cpus)
- per_cpu(cpufreq_cpu_data, j) = policy;
- write_unlock_irqrestore(&cpufreq_driver_lock, flags);
-
if (!frozen) {
ret = cpufreq_add_dev_interface(policy, dev);
if (ret)
goto err_out_unregister;
+ blocking_notifier_call_chain(&cpufreq_policy_notifier_list,
+ CPUFREQ_CREATE_POLICY, policy);
}
write_lock_irqsave(&cpufreq_driver_lock, flags);
return 0;
err_out_unregister:
+err_get_freq:
write_lock_irqsave(&cpufreq_driver_lock, flags);
for_each_cpu(j, policy->cpus)
per_cpu(cpufreq_cpu_data, j) = NULL;
write_unlock_irqrestore(&cpufreq_driver_lock, flags);
-err_get_freq:
if (cpufreq_driver->exit)
cpufreq_driver->exit(policy);
err_set_policy_cpu:
pr_err("%s: Failed to change cpu frequency: %d\n",
__func__, retval);
- if (notify) {
- /*
- * Notify with old freq in case we failed to change
- * frequency
- */
- if (retval)
- freqs.new = freqs.old;
-
- cpufreq_notify_transition(policy, &freqs,
- CPUFREQ_POSTCHANGE);
- }
+ if (notify)
+ cpufreq_notify_post_transition(policy, &freqs, retval);
}
out:
{
int i;
+ mutex_lock(&cpufreq_governor_lock);
if (!policy->governor_enabled)
- return;
+ goto out_unlock;
if (!all_cpus) {
/*
for_each_cpu(i, policy->cpus)
__gov_queue_work(i, dbs_data, delay);
}
+
+out_unlock:
+ mutex_unlock(&cpufreq_governor_lock);
}
EXPORT_SYMBOL_GPL(gov_queue_work);
return sprintf(buf, "%u\n", dbs_data->min_sampling_rate); \
}
+extern struct mutex cpufreq_governor_lock;
+
void dbs_check_cpu(struct dbs_data *dbs_data, int cpu);
bool need_load_eval(struct cpu_dbs_common_info *cdbs,
unsigned int sampling_rate);
return -1;
}
-/* should be called late in the CPU removal sequence so that the stats
- * memory is still available in case someone tries to use it.
- */
-static void cpufreq_stats_free_table(unsigned int cpu)
+static void __cpufreq_stats_free_table(struct cpufreq_policy *policy)
{
- struct cpufreq_stats *stat = per_cpu(cpufreq_stats_table, cpu);
+ struct cpufreq_stats *stat = per_cpu(cpufreq_stats_table, policy->cpu);
- if (stat) {
- pr_debug("%s: Free stat table\n", __func__);
- kfree(stat->time_in_state);
- kfree(stat);
- per_cpu(cpufreq_stats_table, cpu) = NULL;
- }
+ if (!stat)
+ return;
+
+ pr_debug("%s: Free stat table\n", __func__);
+
+ sysfs_remove_group(&policy->kobj, &stats_attr_group);
+ kfree(stat->time_in_state);
+ kfree(stat);
+ per_cpu(cpufreq_stats_table, policy->cpu) = NULL;
}
-/* must be called early in the CPU removal sequence (before
- * cpufreq_remove_dev) so that policy is still valid.
- */
-static void cpufreq_stats_free_sysfs(unsigned int cpu)
+static void cpufreq_stats_free_table(unsigned int cpu)
{
- struct cpufreq_policy *policy = cpufreq_cpu_get(cpu);
+ struct cpufreq_policy *policy;
+ policy = cpufreq_cpu_get(cpu);
if (!policy)
return;
- if (!cpufreq_frequency_get_table(cpu))
- goto put_ref;
-
- if (!policy_is_shared(policy)) {
- pr_debug("%s: Free sysfs stat\n", __func__);
- sysfs_remove_group(&policy->kobj, &stats_attr_group);
- }
+ if (cpufreq_frequency_get_table(policy->cpu))
+ __cpufreq_stats_free_table(policy);
-put_ref:
cpufreq_cpu_put(policy);
}
-static int cpufreq_stats_create_table(struct cpufreq_policy *policy,
+static int __cpufreq_stats_create_table(struct cpufreq_policy *policy,
struct cpufreq_frequency_table *table)
{
unsigned int i, j, count = 0, ret = 0;
return ret;
}
+static void cpufreq_stats_create_table(unsigned int cpu)
+{
+ struct cpufreq_policy *policy;
+ struct cpufreq_frequency_table *table;
+
+ /*
+ * "likely(!policy)" because normally cpufreq_stats will be registered
+ * before cpufreq driver
+ */
+ policy = cpufreq_cpu_get(cpu);
+ if (likely(!policy))
+ return;
+
+ table = cpufreq_frequency_get_table(policy->cpu);
+ if (likely(table))
+ __cpufreq_stats_create_table(policy, table);
+
+ cpufreq_cpu_put(policy);
+}
+
static void cpufreq_stats_update_policy_cpu(struct cpufreq_policy *policy)
{
struct cpufreq_stats *stat = per_cpu(cpufreq_stats_table,
static int cpufreq_stat_notifier_policy(struct notifier_block *nb,
unsigned long val, void *data)
{
- int ret;
+ int ret = 0;
struct cpufreq_policy *policy = data;
struct cpufreq_frequency_table *table;
unsigned int cpu = policy->cpu;
return 0;
}
- if (val != CPUFREQ_NOTIFY)
- return 0;
table = cpufreq_frequency_get_table(cpu);
if (!table)
return 0;
- ret = cpufreq_stats_create_table(policy, table);
- if (ret)
- return ret;
- return 0;
+
+ if (val == CPUFREQ_CREATE_POLICY)
+ ret = __cpufreq_stats_create_table(policy, table);
+ else if (val == CPUFREQ_REMOVE_POLICY)
+ __cpufreq_stats_free_table(policy);
+
+ return ret;
}
static int cpufreq_stat_notifier_trans(struct notifier_block *nb,
return 0;
}
-static int cpufreq_stat_cpu_callback(struct notifier_block *nfb,
- unsigned long action,
- void *hcpu)
-{
- unsigned int cpu = (unsigned long)hcpu;
-
- switch (action) {
- case CPU_DOWN_PREPARE:
- cpufreq_stats_free_sysfs(cpu);
- break;
- case CPU_DEAD:
- cpufreq_stats_free_table(cpu);
- break;
- }
- return NOTIFY_OK;
-}
-
-/* priority=1 so this will get called before cpufreq_remove_dev */
-static struct notifier_block cpufreq_stat_cpu_notifier __refdata = {
- .notifier_call = cpufreq_stat_cpu_callback,
- .priority = 1,
-};
-
static struct notifier_block notifier_policy_block = {
.notifier_call = cpufreq_stat_notifier_policy
};
if (ret)
return ret;
- register_hotcpu_notifier(&cpufreq_stat_cpu_notifier);
+ for_each_online_cpu(cpu)
+ cpufreq_stats_create_table(cpu);
ret = cpufreq_register_notifier(¬ifier_trans_block,
CPUFREQ_TRANSITION_NOTIFIER);
if (ret) {
cpufreq_unregister_notifier(¬ifier_policy_block,
CPUFREQ_POLICY_NOTIFIER);
- unregister_hotcpu_notifier(&cpufreq_stat_cpu_notifier);
for_each_online_cpu(cpu)
cpufreq_stats_free_table(cpu);
return ret;
CPUFREQ_POLICY_NOTIFIER);
cpufreq_unregister_notifier(¬ifier_trans_block,
CPUFREQ_TRANSITION_NOTIFIER);
- unregister_hotcpu_notifier(&cpufreq_stat_cpu_notifier);
- for_each_online_cpu(cpu) {
+ for_each_online_cpu(cpu)
cpufreq_stats_free_table(cpu);
- cpufreq_stats_free_sysfs(cpu);
- }
}
MODULE_AUTHOR("Zou Nan hai <nanhai.zou@intel.com>");
return 0;
}
-static unsigned int davinci_getspeed(unsigned int cpu)
-{
- if (cpu)
- return 0;
-
- return clk_get_rate(cpufreq.armclk) / 1000;
-}
-
static int davinci_target(struct cpufreq_policy *policy, unsigned int idx)
{
struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data;
unsigned int old_freq, new_freq;
int ret = 0;
- old_freq = davinci_getspeed(0);
+ old_freq = policy->cur;
new_freq = pdata->freq_table[idx].frequency;
/* if moving to higher frequency, up the voltage beforehand */
return result;
}
+ policy->clk = cpufreq.armclk;
+
/*
* Time measurement across the target() function yields ~1500-1800us
* time taken with no drivers on notification list.
}
static struct cpufreq_driver davinci_driver = {
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = davinci_verify_speed,
.target_index = davinci_target,
- .get = davinci_getspeed,
+ .get = cpufreq_generic_get,
.init = davinci_cpu_init,
.exit = cpufreq_generic_exit,
.name = "davinci",
return clk_set_rate(armss_clk, freq_table[index].frequency * 1000);
}
-static unsigned int dbx500_cpufreq_getspeed(unsigned int cpu)
-{
- int i = 0;
- unsigned long freq = clk_get_rate(armss_clk) / 1000;
-
- /* The value is rounded to closest frequency in the defined table. */
- while (freq_table[i + 1].frequency != CPUFREQ_TABLE_END) {
- if (freq < freq_table[i].frequency +
- (freq_table[i + 1].frequency - freq_table[i].frequency) / 2)
- return freq_table[i].frequency;
- i++;
- }
-
- return freq_table[i].frequency;
-}
-
static int dbx500_cpufreq_init(struct cpufreq_policy *policy)
{
+ policy->clk = armss_clk;
return cpufreq_generic_init(policy, freq_table, 20 * 1000);
}
static struct cpufreq_driver dbx500_cpufreq_driver = {
- .flags = CPUFREQ_STICKY | CPUFREQ_CONST_LOOPS,
+ .flags = CPUFREQ_STICKY | CPUFREQ_CONST_LOOPS |
+ CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = dbx500_cpufreq_target,
- .get = dbx500_cpufreq_getspeed,
+ .get = cpufreq_generic_get,
.init = dbx500_cpufreq_init,
.name = "DBX500",
.attr = cpufreq_generic_attr,
#include <linux/regulator/consumer.h>
#include <linux/cpufreq.h>
#include <linux/suspend.h>
+#include <linux/platform_device.h>
#include <plat/cpu.h>
static bool frequency_locked;
static DEFINE_MUTEX(cpufreq_lock);
-static unsigned int exynos_getspeed(unsigned int cpu)
-{
- return clk_get_rate(exynos_info->cpu_clk) / 1000;
-}
-
static int exynos_cpufreq_get_index(unsigned int freq)
{
struct cpufreq_frequency_table *freq_table = exynos_info->freq_table;
static int exynos_cpufreq_cpu_init(struct cpufreq_policy *policy)
{
+ policy->clk = exynos_info->cpu_clk;
return cpufreq_generic_init(policy, exynos_info->freq_table, 100000);
}
static struct cpufreq_driver exynos_driver = {
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = exynos_target,
- .get = exynos_getspeed,
+ .get = cpufreq_generic_get,
.init = exynos_cpufreq_cpu_init,
.exit = cpufreq_generic_exit,
.name = "exynos_cpufreq",
#endif
};
-static int __init exynos_cpufreq_init(void)
+static int exynos_cpufreq_probe(struct platform_device *pdev)
{
int ret = -EINVAL;
goto err_vdd_arm;
}
- locking_frequency = exynos_getspeed(0);
+ locking_frequency = clk_get_rate(exynos_info->cpu_clk) / 1000;
register_pm_notifier(&exynos_cpufreq_nb);
kfree(exynos_info);
return -EINVAL;
}
-late_initcall(exynos_cpufreq_init);
+
+static struct platform_driver exynos_cpufreq_platdrv = {
+ .driver = {
+ .name = "exynos-cpufreq",
+ .owner = THIS_MODULE,
+ },
+ .probe = exynos_cpufreq_probe,
+};
+module_platform_driver(exynos_cpufreq_platdrv);
cpu_relax();
}
-static void set_apll(unsigned int new_index,
- unsigned int old_index)
+static void set_apll(unsigned int index)
{
- unsigned int tmp, pdiv;
+ unsigned int tmp;
+ unsigned int freq = apll_freq_5250[index].freq;
- /* 1. MUX_CORE_SEL = MPLL, ARMCLK uses MPLL for lock time */
+ /* MUX_CORE_SEL = MPLL, ARMCLK uses MPLL for lock time */
clk_set_parent(moutcore, mout_mpll);
do {
tmp &= 0x7;
} while (tmp != 0x2);
- /* 2. Set APLL Lock time */
- pdiv = ((apll_freq_5250[new_index].mps >> 8) & 0x3f);
-
- __raw_writel((pdiv * 250), EXYNOS5_APLL_LOCK);
+ clk_set_rate(mout_apll, freq * 1000);
- /* 3. Change PLL PMS values */
- tmp = __raw_readl(EXYNOS5_APLL_CON0);
- tmp &= ~((0x3ff << 16) | (0x3f << 8) | (0x7 << 0));
- tmp |= apll_freq_5250[new_index].mps;
- __raw_writel(tmp, EXYNOS5_APLL_CON0);
-
- /* 4. wait_lock_time */
- do {
- cpu_relax();
- tmp = __raw_readl(EXYNOS5_APLL_CON0);
- } while (!(tmp & (0x1 << 29)));
-
- /* 5. MUX_CORE_SEL = APLL */
+ /* MUX_CORE_SEL = APLL */
clk_set_parent(moutcore, mout_apll);
do {
tmp = __raw_readl(EXYNOS5_CLKMUX_STATCPU);
tmp &= (0x7 << 16);
} while (tmp != (0x1 << 16));
-
-}
-
-static bool exynos5250_pms_change(unsigned int old_index, unsigned int new_index)
-{
- unsigned int old_pm = apll_freq_5250[old_index].mps >> 8;
- unsigned int new_pm = apll_freq_5250[new_index].mps >> 8;
-
- return (old_pm == new_pm) ? 0 : 1;
}
static void exynos5250_set_frequency(unsigned int old_index,
unsigned int new_index)
{
- unsigned int tmp;
-
if (old_index > new_index) {
- if (!exynos5250_pms_change(old_index, new_index)) {
- /* 1. Change the system clock divider values */
- set_clkdiv(new_index);
- /* 2. Change just s value in apll m,p,s value */
- tmp = __raw_readl(EXYNOS5_APLL_CON0);
- tmp &= ~(0x7 << 0);
- tmp |= apll_freq_5250[new_index].mps & 0x7;
- __raw_writel(tmp, EXYNOS5_APLL_CON0);
-
- } else {
- /* Clock Configuration Procedure */
- /* 1. Change the system clock divider values */
- set_clkdiv(new_index);
- /* 2. Change the apll m,p,s value */
- set_apll(new_index, old_index);
- }
+ set_clkdiv(new_index);
+ set_apll(new_index);
} else if (old_index < new_index) {
- if (!exynos5250_pms_change(old_index, new_index)) {
- /* 1. Change just s value in apll m,p,s value */
- tmp = __raw_readl(EXYNOS5_APLL_CON0);
- tmp &= ~(0x7 << 0);
- tmp |= apll_freq_5250[new_index].mps & 0x7;
- __raw_writel(tmp, EXYNOS5_APLL_CON0);
- /* 2. Change the system clock divider values */
- set_clkdiv(new_index);
- } else {
- /* Clock Configuration Procedure */
- /* 1. Change the apll m,p,s value */
- set_apll(new_index, old_index);
- /* 2. Change the system clock divider values */
- set_clkdiv(new_index);
- }
+ set_apll(new_index);
+ set_clkdiv(new_index);
}
}
info->volt_table = exynos5250_volt_table;
info->freq_table = exynos5250_freq_table;
info->set_freq = exynos5250_set_frequency;
- info->need_apll_change = exynos5250_pms_change;
return 0;
struct resource *mem;
int irq;
struct clk *cpu_clk;
- unsigned int cur_frequency;
unsigned int latency;
struct cpufreq_frequency_table *freq_table;
unsigned int freq_count;
return 0;
}
-static void exynos_enable_dvfs(void)
+static void exynos_enable_dvfs(unsigned int cur_frequency)
{
unsigned int tmp, i, cpu;
struct cpufreq_frequency_table *freq_table = dvfs_info->freq_table;
/* Set initial performance index */
for (i = 0; freq_table[i].frequency != CPUFREQ_TABLE_END; i++)
- if (freq_table[i].frequency == dvfs_info->cur_frequency)
+ if (freq_table[i].frequency == cur_frequency)
break;
if (freq_table[i].frequency == CPUFREQ_TABLE_END) {
dev_crit(dvfs_info->dev, "Boot up frequency not supported\n");
/* Assign the highest frequency */
i = 0;
- dvfs_info->cur_frequency = freq_table[i].frequency;
+ cur_frequency = freq_table[i].frequency;
}
dev_info(dvfs_info->dev, "Setting dvfs initial frequency = %uKHZ",
- dvfs_info->cur_frequency);
+ cur_frequency);
for (cpu = 0; cpu < CONFIG_NR_CPUS; cpu++) {
tmp = __raw_readl(dvfs_info->base + XMU_C0_3_PSTATE + cpu * 4);
dvfs_info->base + XMU_DVFS_CTRL);
}
-static unsigned int exynos_getspeed(unsigned int cpu)
-{
- return dvfs_info->cur_frequency;
-}
-
static int exynos_target(struct cpufreq_policy *policy, unsigned int index)
{
unsigned int tmp;
mutex_lock(&cpufreq_lock);
- freqs.old = dvfs_info->cur_frequency;
+ freqs.old = policy->cur;
freqs.new = freq_table[index].frequency;
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
goto skip_work;
mutex_lock(&cpufreq_lock);
- freqs.old = dvfs_info->cur_frequency;
+ freqs.old = policy->cur;
cur_pstate = __raw_readl(dvfs_info->base + XMU_P_STATUS);
if (cur_pstate >> C0_3_PSTATE_VALID_SHIFT & 0x1)
if (likely(index < dvfs_info->freq_count)) {
freqs.new = freq_table[index].frequency;
- dvfs_info->cur_frequency = freqs.new;
} else {
dev_crit(dvfs_info->dev, "New frequency out of range\n");
- freqs.new = dvfs_info->cur_frequency;
+ freqs.new = freqs.old;
}
cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
static int exynos_cpufreq_cpu_init(struct cpufreq_policy *policy)
{
+ policy->clk = dvfs_info->cpu_clk;
return cpufreq_generic_init(policy, dvfs_info->freq_table,
dvfs_info->latency);
}
static struct cpufreq_driver exynos_driver = {
- .flags = CPUFREQ_STICKY | CPUFREQ_ASYNC_NOTIFICATION,
+ .flags = CPUFREQ_STICKY | CPUFREQ_ASYNC_NOTIFICATION |
+ CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = exynos_target,
- .get = exynos_getspeed,
+ .get = cpufreq_generic_get,
.init = exynos_cpufreq_cpu_init,
.exit = cpufreq_generic_exit,
.name = CPUFREQ_NAME,
int ret = -EINVAL;
struct device_node *np;
struct resource res;
+ unsigned int cur_frequency;
np = pdev->dev.of_node;
if (!np)
goto err_free_table;
}
- dvfs_info->cur_frequency = clk_get_rate(dvfs_info->cpu_clk);
- if (!dvfs_info->cur_frequency) {
+ cur_frequency = clk_get_rate(dvfs_info->cpu_clk);
+ if (!cur_frequency) {
dev_err(dvfs_info->dev, "Failed to get clock rate\n");
ret = -EINVAL;
goto err_free_table;
}
- dvfs_info->cur_frequency /= 1000;
+ cur_frequency /= 1000;
INIT_WORK(&dvfs_info->irq_work, exynos_cpufreq_work);
ret = devm_request_irq(dvfs_info->dev, dvfs_info->irq,
goto err_free_table;
}
- exynos_enable_dvfs();
+ exynos_enable_dvfs(cur_frequency);
ret = cpufreq_register_driver(&exynos_driver);
if (ret) {
dev_err(dvfs_info->dev,
}
EXPORT_SYMBOL_GPL(cpufreq_frequency_table_target);
+int cpufreq_frequency_table_get_index(struct cpufreq_policy *policy,
+ unsigned int freq)
+{
+ struct cpufreq_frequency_table *table;
+ int i;
+
+ table = cpufreq_frequency_get_table(policy->cpu);
+ if (unlikely(!table)) {
+ pr_debug("%s: Unable to find frequency table\n", __func__);
+ return -ENOENT;
+ }
+
+ for (i = 0; table[i].frequency != CPUFREQ_TABLE_END; i++) {
+ if (table[i].frequency == freq)
+ return i;
+ }
+
+ return -EINVAL;
+}
+EXPORT_SYMBOL_GPL(cpufreq_frequency_table_get_index);
+
static DEFINE_PER_CPU(struct cpufreq_frequency_table *, cpufreq_show_table);
+
/**
* show_available_freqs - show available frequencies for the specified CPU
*/
static struct cpufreq_frequency_table *freq_table;
static unsigned int transition_latency;
-static unsigned int imx6q_get_speed(unsigned int cpu)
-{
- return clk_get_rate(arm_clk) / 1000;
-}
+static u32 *imx6_soc_volt;
+static u32 soc_opp_count;
static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index)
{
/* scaling up? scale voltage before frequency */
if (new_freq > old_freq) {
+ ret = regulator_set_voltage_tol(pu_reg, imx6_soc_volt[index], 0);
+ if (ret) {
+ dev_err(cpu_dev, "failed to scale vddpu up: %d\n", ret);
+ return ret;
+ }
+ ret = regulator_set_voltage_tol(soc_reg, imx6_soc_volt[index], 0);
+ if (ret) {
+ dev_err(cpu_dev, "failed to scale vddsoc up: %d\n", ret);
+ return ret;
+ }
ret = regulator_set_voltage_tol(arm_reg, volt, 0);
if (ret) {
dev_err(cpu_dev,
"failed to scale vddarm up: %d\n", ret);
return ret;
}
-
- /*
- * Need to increase vddpu and vddsoc for safety
- * if we are about to run at 1.2 GHz.
- */
- if (new_freq == FREQ_1P2_GHZ / 1000) {
- regulator_set_voltage_tol(pu_reg,
- PU_SOC_VOLTAGE_HIGH, 0);
- regulator_set_voltage_tol(soc_reg,
- PU_SOC_VOLTAGE_HIGH, 0);
- }
}
/*
"failed to scale vddarm down: %d\n", ret);
ret = 0;
}
-
- if (old_freq == FREQ_1P2_GHZ / 1000) {
- regulator_set_voltage_tol(pu_reg,
- PU_SOC_VOLTAGE_NORMAL, 0);
- regulator_set_voltage_tol(soc_reg,
- PU_SOC_VOLTAGE_NORMAL, 0);
+ ret = regulator_set_voltage_tol(soc_reg, imx6_soc_volt[index], 0);
+ if (ret) {
+ dev_warn(cpu_dev, "failed to scale vddsoc down: %d\n", ret);
+ ret = 0;
+ }
+ ret = regulator_set_voltage_tol(pu_reg, imx6_soc_volt[index], 0);
+ if (ret) {
+ dev_warn(cpu_dev, "failed to scale vddpu down: %d\n", ret);
+ ret = 0;
}
}
static int imx6q_cpufreq_init(struct cpufreq_policy *policy)
{
+ policy->clk = arm_clk;
return cpufreq_generic_init(policy, freq_table, transition_latency);
}
static struct cpufreq_driver imx6q_cpufreq_driver = {
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = imx6q_set_target,
- .get = imx6q_get_speed,
+ .get = cpufreq_generic_get,
.init = imx6q_cpufreq_init,
.exit = cpufreq_generic_exit,
.name = "imx6q-cpufreq",
struct dev_pm_opp *opp;
unsigned long min_volt, max_volt;
int num, ret;
+ const struct property *prop;
+ const __be32 *val;
+ u32 nr, i, j;
cpu_dev = get_cpu_device(0);
if (!cpu_dev) {
goto put_node;
}
- /* We expect an OPP table supplied by platform */
+ /*
+ * We expect an OPP table supplied by platform.
+ * Just, incase the platform did not supply the OPP
+ * table, it will try to get it.
+ */
num = dev_pm_opp_get_opp_count(cpu_dev);
if (num < 0) {
- ret = num;
- dev_err(cpu_dev, "no OPP table is found: %d\n", ret);
- goto put_node;
+ ret = of_init_opp_table(cpu_dev);
+ if (ret < 0) {
+ dev_err(cpu_dev, "failed to init OPP table: %d\n", ret);
+ goto put_node;
+ }
+
+ num = dev_pm_opp_get_opp_count(cpu_dev);
+ if (num < 0) {
+ ret = num;
+ dev_err(cpu_dev, "no OPP table is found: %d\n", ret);
+ goto put_node;
+ }
}
ret = dev_pm_opp_init_cpufreq_table(cpu_dev, &freq_table);
goto put_node;
}
+ /* Make imx6_soc_volt array's size same as arm opp number */
+ imx6_soc_volt = devm_kzalloc(cpu_dev, sizeof(*imx6_soc_volt) * num, GFP_KERNEL);
+ if (imx6_soc_volt == NULL) {
+ ret = -ENOMEM;
+ goto free_freq_table;
+ }
+
+ prop = of_find_property(np, "fsl,soc-operating-points", NULL);
+ if (!prop || !prop->value)
+ goto soc_opp_out;
+
+ /*
+ * Each OPP is a set of tuples consisting of frequency and
+ * voltage like <freq-kHz vol-uV>.
+ */
+ nr = prop->length / sizeof(u32);
+ if (nr % 2 || (nr / 2) < num)
+ goto soc_opp_out;
+
+ for (j = 0; j < num; j++) {
+ val = prop->value;
+ for (i = 0; i < nr / 2; i++) {
+ unsigned long freq = be32_to_cpup(val++);
+ unsigned long volt = be32_to_cpup(val++);
+ if (freq_table[j].frequency == freq) {
+ imx6_soc_volt[soc_opp_count++] = volt;
+ break;
+ }
+ }
+ }
+
+soc_opp_out:
+ /* use fixed soc opp volt if no valid soc opp info found in dtb */
+ if (soc_opp_count != num) {
+ dev_warn(cpu_dev, "can NOT find valid fsl,soc-operating-points property in dtb, use default value!\n");
+ for (j = 0; j < num; j++)
+ imx6_soc_volt[j] = PU_SOC_VOLTAGE_NORMAL;
+ if (freq_table[num - 1].frequency * 1000 == FREQ_1P2_GHZ)
+ imx6_soc_volt[num - 1] = PU_SOC_VOLTAGE_HIGH;
+ }
+
if (of_property_read_u32(np, "clock-latency", &transition_latency))
transition_latency = CPUFREQ_ETERNAL;
+ /*
+ * Calculate the ramp time for max voltage change in the
+ * VDDSOC and VDDPU regulators.
+ */
+ ret = regulator_set_voltage_time(soc_reg, imx6_soc_volt[0], imx6_soc_volt[num - 1]);
+ if (ret > 0)
+ transition_latency += ret * 1000;
+ ret = regulator_set_voltage_time(pu_reg, imx6_soc_volt[0], imx6_soc_volt[num - 1]);
+ if (ret > 0)
+ transition_latency += ret * 1000;
+
/*
* OPP is maintained in order of increasing frequency, and
* freq_table initialised from OPP is therefore sorted in the
if (ret > 0)
transition_latency += ret * 1000;
- /* Count vddpu and vddsoc latency in for 1.2 GHz support */
- if (freq_table[num].frequency == FREQ_1P2_GHZ / 1000) {
- ret = regulator_set_voltage_time(pu_reg, PU_SOC_VOLTAGE_NORMAL,
- PU_SOC_VOLTAGE_HIGH);
- if (ret > 0)
- transition_latency += ret * 1000;
- ret = regulator_set_voltage_time(soc_reg, PU_SOC_VOLTAGE_NORMAL,
- PU_SOC_VOLTAGE_HIGH);
- if (ret > 0)
- transition_latency += ret * 1000;
- }
-
ret = cpufreq_register_driver(&imx6q_cpufreq_driver);
if (ret) {
dev_err(cpu_dev, "failed register driver: %d\n", ret);
}
static struct cpufreq_driver integrator_driver = {
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = integrator_verify_policy,
.target = integrator_set_target,
.get = integrator_get,
#define SAMPLE_COUNT 3
#define BYT_RATIOS 0x66a
+#define BYT_VIDS 0x66b
#define FRAC_BITS 8
#define int_tofp(X) ((int64_t)(X) << FRAC_BITS)
int turbo_pstate;
};
+struct vid_data {
+ int32_t min;
+ int32_t max;
+ int32_t ratio;
+};
+
struct _pid {
int setpoint;
int32_t integral;
struct timer_list timer;
struct pstate_data pstate;
+ struct vid_data vid;
struct _pid pid;
- int min_pstate_count;
-
u64 prev_aperf;
u64 prev_mperf;
int sample_ptr;
int (*get_max)(void);
int (*get_min)(void);
int (*get_turbo)(void);
- void (*set)(int pstate);
+ void (*set)(struct cpudata*, int pstate);
+ void (*get_vid)(struct cpudata *);
};
struct cpu_defaults {
return (value >> 16) & 0xFF;
}
+static void byt_set_pstate(struct cpudata *cpudata, int pstate)
+{
+ u64 val;
+ int32_t vid_fp;
+ u32 vid;
+
+ val = pstate << 8;
+ if (limits.no_turbo)
+ val |= (u64)1 << 32;
+
+ vid_fp = cpudata->vid.min + mul_fp(
+ int_tofp(pstate - cpudata->pstate.min_pstate),
+ cpudata->vid.ratio);
+
+ vid_fp = clamp_t(int32_t, vid_fp, cpudata->vid.min, cpudata->vid.max);
+ vid = fp_toint(vid_fp);
+
+ val |= vid;
+
+ wrmsrl(MSR_IA32_PERF_CTL, val);
+}
+
+static void byt_get_vid(struct cpudata *cpudata)
+{
+ u64 value;
+
+ rdmsrl(BYT_VIDS, value);
+ cpudata->vid.min = int_tofp((value >> 8) & 0x7f);
+ cpudata->vid.max = int_tofp((value >> 16) & 0x7f);
+ cpudata->vid.ratio = div_fp(
+ cpudata->vid.max - cpudata->vid.min,
+ int_tofp(cpudata->pstate.max_pstate -
+ cpudata->pstate.min_pstate));
+}
+
+
static int core_get_min_pstate(void)
{
u64 value;
return ret;
}
-static void core_set_pstate(int pstate)
+static void core_set_pstate(struct cpudata *cpudata, int pstate)
{
u64 val;
.get_max = byt_get_max_pstate,
.get_min = byt_get_min_pstate,
.get_turbo = byt_get_max_pstate,
- .set = core_set_pstate,
+ .set = byt_set_pstate,
+ .get_vid = byt_get_vid,
},
};
cpu->pstate.current_pstate = pstate;
- pstate_funcs.set(pstate);
+ pstate_funcs.set(cpu, pstate);
}
static inline void intel_pstate_pstate_increase(struct cpudata *cpu, int steps)
cpu->pstate.max_pstate = pstate_funcs.get_max();
cpu->pstate.turbo_pstate = pstate_funcs.get_turbo();
+ if (pstate_funcs.get_vid)
+ pstate_funcs.get_vid(cpu);
+
/*
* goto max pstate so we don't slow up boot if we are built-in if we are
* a module we will take care of it during normal operation
intel_pstate_sample(cpu);
intel_pstate_adjust_busy_pstate(cpu);
-
- if (cpu->pstate.current_pstate == cpu->pstate.min_pstate) {
- cpu->min_pstate_count++;
- if (!(cpu->min_pstate_count % 5)) {
- intel_pstate_set_pstate(cpu, cpu->pstate.max_pstate);
- }
- } else
- cpu->min_pstate_count = 0;
-
intel_pstate_set_sample_time(cpu);
}
pstate_funcs.get_min = funcs->get_min;
pstate_funcs.get_turbo = funcs->get_turbo;
pstate_funcs.set = funcs->set;
+ pstate_funcs.get_vid = funcs->get_vid;
}
#if IS_ENABLED(CONFIG_ACPI)
}
static struct cpufreq_driver kirkwood_cpufreq_driver = {
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.get = kirkwood_cpufreq_get_cpu_frequency,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = kirkwood_cpufreq_target,
static uint nowait;
-static struct clk *cpuclk;
-
static void (*saved_cpu_wait) (void);
static int loongson2_cpu_freq_notifier(struct notifier_block *nb,
return 0;
}
-static unsigned int loongson2_cpufreq_get(unsigned int cpu)
-{
- return clk_get_rate(cpuclk);
-}
-
/*
* Here we notify other drivers of the proposed change and the final change.
*/
set_cpus_allowed_ptr(current, &cpus_allowed);
/* setting the cpu frequency */
- clk_set_rate(cpuclk, freq);
+ clk_set_rate(policy->clk, freq);
return 0;
}
static int loongson2_cpufreq_cpu_init(struct cpufreq_policy *policy)
{
+ static struct clk *cpuclk;
int i;
unsigned long rate;
int ret;
return ret;
}
+ policy->clk = cpuclk;
return cpufreq_generic_init(policy, &loongson2_clockmod_table[0], 0);
}
static int loongson2_cpufreq_exit(struct cpufreq_policy *policy)
{
cpufreq_frequency_table_put_attr(policy->cpu);
- clk_put(cpuclk);
+ clk_put(policy->clk);
return 0;
}
.init = loongson2_cpufreq_cpu_init,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = loongson2_cpufreq_target,
- .get = loongson2_cpufreq_get,
+ .get = cpufreq_generic_get,
.exit = loongson2_cpufreq_exit,
.attr = cpufreq_generic_attr,
};
static struct cpufreq_frequency_table *freq_table;
static atomic_t freq_table_users = ATOMIC_INIT(0);
-static struct clk *mpu_clk;
static struct device *mpu_dev;
static struct regulator *mpu_reg;
-static unsigned int omap_getspeed(unsigned int cpu)
-{
- unsigned long rate;
-
- if (cpu >= NR_CPUS)
- return 0;
-
- rate = clk_get_rate(mpu_clk) / 1000;
- return rate;
-}
-
static int omap_target(struct cpufreq_policy *policy, unsigned int index)
{
int r, ret;
unsigned long freq, volt = 0, volt_old = 0, tol = 0;
unsigned int old_freq, new_freq;
- old_freq = omap_getspeed(policy->cpu);
+ old_freq = policy->cur;
new_freq = freq_table[index].frequency;
freq = new_freq * 1000;
- ret = clk_round_rate(mpu_clk, freq);
+ ret = clk_round_rate(policy->clk, freq);
if (IS_ERR_VALUE(ret)) {
dev_warn(mpu_dev,
"CPUfreq: Cannot find matching frequency for %lu\n",
}
}
- ret = clk_set_rate(mpu_clk, new_freq * 1000);
+ ret = clk_set_rate(policy->clk, new_freq * 1000);
/* scaling down? scale voltage after frequency */
if (mpu_reg && (new_freq < old_freq)) {
if (r < 0) {
dev_warn(mpu_dev, "%s: unable to scale voltage down.\n",
__func__);
- clk_set_rate(mpu_clk, old_freq * 1000);
+ clk_set_rate(policy->clk, old_freq * 1000);
return r;
}
}
{
int result;
- mpu_clk = clk_get(NULL, "cpufreq_ck");
- if (IS_ERR(mpu_clk))
- return PTR_ERR(mpu_clk);
+ policy->clk = clk_get(NULL, "cpufreq_ck");
+ if (IS_ERR(policy->clk))
+ return PTR_ERR(policy->clk);
if (!freq_table) {
result = dev_pm_opp_init_cpufreq_table(mpu_dev, &freq_table);
freq_table_free();
fail:
- clk_put(mpu_clk);
+ clk_put(policy->clk);
return result;
}
{
cpufreq_frequency_table_put_attr(policy->cpu);
freq_table_free();
- clk_put(mpu_clk);
+ clk_put(policy->clk);
return 0;
}
static struct cpufreq_driver omap_driver = {
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = omap_target,
- .get = omap_getspeed,
+ .get = cpufreq_generic_get,
.init = omap_cpu_init,
.exit = omap_cpu_exit,
.name = "omap",
cpu, target_freq,
(pcch_virt_addr + pcc_cpu_data->input_offset));
+ freqs.old = policy->cur;
freqs.new = target_freq;
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
memset_io((pcch_virt_addr + pcc_cpu_data->input_offset), 0, BUF_SZ);
status = ioread16(&pcch_hdr->status);
+ iowrite16(0, &pcch_hdr->status);
+
+ cpufreq_notify_post_transition(policy, &freqs, status != CMD_COMPLETE);
+ spin_unlock(&pcc_lock);
+
if (status != CMD_COMPLETE) {
pr_debug("target: FAILED for cpu %d, with status: 0x%x\n",
cpu, status);
- goto cmd_incomplete;
+ return -EINVAL;
}
- iowrite16(0, &pcch_hdr->status);
- cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
pr_debug("target: was SUCCESSFUL for cpu %d\n", cpu);
- spin_unlock(&pcc_lock);
return 0;
-
-cmd_incomplete:
- freqs.new = freqs.old;
- cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
- iowrite16(0, &pcch_hdr->status);
- spin_unlock(&pcc_lock);
- return -EINVAL;
}
static int pcc_get_offset(int cpu)
static unsigned int busfreq; /* FSB, in 10 kHz */
static unsigned int max_multiplier;
+static unsigned int param_busfreq = 0;
+static unsigned int param_max_multiplier = 0;
+
+module_param_named(max_multiplier, param_max_multiplier, uint, S_IRUGO);
+MODULE_PARM_DESC(max_multiplier, "Maximum multiplier (allowed values: 20 30 35 40 45 50 55 60)");
+
+module_param_named(bus_frequency, param_busfreq, uint, S_IRUGO);
+MODULE_PARM_DESC(bus_frequency, "Bus frequency in kHz");
/* Clock ratio multiplied by 10 - see table 27 in AMD#23446 */
static struct cpufreq_frequency_table clock_ratio[] = {
- {45, /* 000 -> 4.5x */ 0},
+ {60, /* 110 -> 6.0x */ 0},
+ {55, /* 011 -> 5.5x */ 0},
{50, /* 001 -> 5.0x */ 0},
+ {45, /* 000 -> 4.5x */ 0},
{40, /* 010 -> 4.0x */ 0},
- {55, /* 011 -> 5.5x */ 0},
- {20, /* 100 -> 2.0x */ 0},
- {30, /* 101 -> 3.0x */ 0},
- {60, /* 110 -> 6.0x */ 0},
{35, /* 111 -> 3.5x */ 0},
+ {30, /* 101 -> 3.0x */ 0},
+ {20, /* 100 -> 2.0x */ 0},
{0, CPUFREQ_TABLE_END}
};
+static const u8 index_to_register[8] = { 6, 3, 1, 0, 2, 7, 5, 4 };
+static const u8 register_to_index[8] = { 3, 2, 4, 1, 7, 6, 0, 5 };
+
+static const struct {
+ unsigned freq;
+ unsigned mult;
+} usual_frequency_table[] = {
+ { 400000, 40 }, // 100 * 4
+ { 450000, 45 }, // 100 * 4.5
+ { 475000, 50 }, // 95 * 5
+ { 500000, 50 }, // 100 * 5
+ { 506250, 45 }, // 112.5 * 4.5
+ { 533500, 55 }, // 97 * 5.5
+ { 550000, 55 }, // 100 * 5.5
+ { 562500, 50 }, // 112.5 * 5
+ { 570000, 60 }, // 95 * 6
+ { 600000, 60 }, // 100 * 6
+ { 618750, 55 }, // 112.5 * 5.5
+ { 660000, 55 }, // 120 * 5.5
+ { 675000, 60 }, // 112.5 * 6
+ { 720000, 60 }, // 120 * 6
+};
+
+#define FREQ_RANGE 3000
/**
* powernow_k6_get_cpu_multiplier - returns the current FSB multiplier
*
- * Returns the current setting of the frequency multiplier. Core clock
+ * Returns the current setting of the frequency multiplier. Core clock
* speed is frequency of the Front-Side Bus multiplied with this value.
*/
static int powernow_k6_get_cpu_multiplier(void)
{
- u64 invalue = 0;
+ unsigned long invalue = 0;
u32 msrval;
+ local_irq_disable();
+
msrval = POWERNOW_IOPORT + 0x1;
wrmsr(MSR_K6_EPMR, msrval, 0); /* enable the PowerNow port */
invalue = inl(POWERNOW_IOPORT + 0x8);
msrval = POWERNOW_IOPORT + 0x0;
wrmsr(MSR_K6_EPMR, msrval, 0); /* disable it again */
- return clock_ratio[(invalue >> 5)&7].driver_data;
+ local_irq_enable();
+
+ return clock_ratio[register_to_index[(invalue >> 5)&7]].driver_data;
}
+static void powernow_k6_set_cpu_multiplier(unsigned int best_i)
+{
+ unsigned long outvalue, invalue;
+ unsigned long msrval;
+ unsigned long cr0;
+
+ /* we now need to transform best_i to the BVC format, see AMD#23446 */
+
+ /*
+ * The processor doesn't respond to inquiry cycles while changing the
+ * frequency, so we must disable cache.
+ */
+ local_irq_disable();
+ cr0 = read_cr0();
+ write_cr0(cr0 | X86_CR0_CD);
+ wbinvd();
+
+ outvalue = (1<<12) | (1<<10) | (1<<9) | (index_to_register[best_i]<<5);
+
+ msrval = POWERNOW_IOPORT + 0x1;
+ wrmsr(MSR_K6_EPMR, msrval, 0); /* enable the PowerNow port */
+ invalue = inl(POWERNOW_IOPORT + 0x8);
+ invalue = invalue & 0x1f;
+ outvalue = outvalue | invalue;
+ outl(outvalue, (POWERNOW_IOPORT + 0x8));
+ msrval = POWERNOW_IOPORT + 0x0;
+ wrmsr(MSR_K6_EPMR, msrval, 0); /* disable it again */
+
+ write_cr0(cr0);
+ local_irq_enable();
+}
/**
* powernow_k6_target - set the PowerNow! multiplier
static int powernow_k6_target(struct cpufreq_policy *policy,
unsigned int best_i)
{
- unsigned long outvalue = 0, invalue = 0;
- unsigned long msrval;
struct cpufreq_freqs freqs;
if (clock_ratio[best_i].driver_data > max_multiplier) {
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
- /* we now need to transform best_i to the BVC format, see AMD#23446 */
-
- outvalue = (1<<12) | (1<<10) | (1<<9) | (best_i<<5);
-
- msrval = POWERNOW_IOPORT + 0x1;
- wrmsr(MSR_K6_EPMR, msrval, 0); /* enable the PowerNow port */
- invalue = inl(POWERNOW_IOPORT + 0x8);
- invalue = invalue & 0xf;
- outvalue = outvalue | invalue;
- outl(outvalue , (POWERNOW_IOPORT + 0x8));
- msrval = POWERNOW_IOPORT + 0x0;
- wrmsr(MSR_K6_EPMR, msrval, 0); /* disable it again */
+ powernow_k6_set_cpu_multiplier(best_i);
cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
return 0;
}
-
static int powernow_k6_cpu_init(struct cpufreq_policy *policy)
{
unsigned int i, f;
+ unsigned khz;
if (policy->cpu != 0)
return -ENODEV;
- /* get frequencies */
- max_multiplier = powernow_k6_get_cpu_multiplier();
- busfreq = cpu_khz / max_multiplier;
+ max_multiplier = 0;
+ khz = cpu_khz;
+ for (i = 0; i < ARRAY_SIZE(usual_frequency_table); i++) {
+ if (khz >= usual_frequency_table[i].freq - FREQ_RANGE &&
+ khz <= usual_frequency_table[i].freq + FREQ_RANGE) {
+ khz = usual_frequency_table[i].freq;
+ max_multiplier = usual_frequency_table[i].mult;
+ break;
+ }
+ }
+ if (param_max_multiplier) {
+ for (i = 0; (clock_ratio[i].frequency != CPUFREQ_TABLE_END); i++) {
+ if (clock_ratio[i].driver_data == param_max_multiplier) {
+ max_multiplier = param_max_multiplier;
+ goto have_max_multiplier;
+ }
+ }
+ printk(KERN_ERR "powernow-k6: invalid max_multiplier parameter, valid parameters 20, 30, 35, 40, 45, 50, 55, 60\n");
+ return -EINVAL;
+ }
+
+ if (!max_multiplier) {
+ printk(KERN_WARNING "powernow-k6: unknown frequency %u, cannot determine current multiplier\n", khz);
+ printk(KERN_WARNING "powernow-k6: use module parameters max_multiplier and bus_frequency\n");
+ return -EOPNOTSUPP;
+ }
+
+have_max_multiplier:
+ param_max_multiplier = max_multiplier;
+
+ if (param_busfreq) {
+ if (param_busfreq >= 50000 && param_busfreq <= 150000) {
+ busfreq = param_busfreq / 10;
+ goto have_busfreq;
+ }
+ printk(KERN_ERR "powernow-k6: invalid bus_frequency parameter, allowed range 50000 - 150000 kHz\n");
+ return -EINVAL;
+ }
+
+ busfreq = khz / max_multiplier;
+have_busfreq:
+ param_busfreq = busfreq * 10;
/* table init */
for (i = 0; (clock_ratio[i].frequency != CPUFREQ_TABLE_END); i++) {
}
/* cpuinfo and default policy values */
- policy->cpuinfo.transition_latency = 200000;
+ policy->cpuinfo.transition_latency = 500000;
return cpufreq_table_validate_and_show(policy, clock_ratio);
}
cpufreq_cpu_put(policy);
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
-
res = transition_fid_vid(data, fid, vid);
- if (res)
- freqs.new = freqs.old;
- else
- freqs.new = find_khz_freq_from_fid(data->currfid);
+ cpufreq_notify_post_transition(policy, &freqs, res);
- cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
return res;
}
/**
* struct cpu_data - per CPU data struct
- * @clk: the clk of CPU
* @parent: the parent node of cpu clock
* @table: frequency table
*/
struct cpu_data {
- struct clk *clk;
struct device_node *parent;
struct cpufreq_frequency_table *table;
};
}
#endif
-static unsigned int corenet_cpufreq_get_speed(unsigned int cpu)
-{
- struct cpu_data *data = per_cpu(cpu_data, cpu);
-
- return clk_get_rate(data->clk) / 1000;
-}
-
/* reduce the duplicated frequencies in frequency table */
static void freq_table_redup(struct cpufreq_frequency_table *freq_table,
int count)
goto err_np;
}
- data->clk = of_clk_get(np, 0);
- if (IS_ERR(data->clk)) {
+ policy->clk = of_clk_get(np, 0);
+ if (IS_ERR(policy->clk)) {
pr_err("%s: no clock information\n", __func__);
goto err_nomem2;
}
struct cpu_data *data = per_cpu(cpu_data, policy->cpu);
parent = of_clk_get(data->parent, data->table[index].driver_data);
- return clk_set_parent(data->clk, parent);
+ return clk_set_parent(policy->clk, parent);
}
static struct cpufreq_driver ppc_corenet_cpufreq_driver = {
.exit = __exit_p(corenet_cpufreq_cpu_exit),
.verify = cpufreq_generic_frequency_table_verify,
.target_index = corenet_cpufreq_target,
- .get = corenet_cpufreq_get_speed,
+ .get = cpufreq_generic_get,
.attr = cpufreq_generic_attr,
};
}
static struct cpufreq_driver pxa_cpufreq_driver = {
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = pxa_set_target,
.init = pxa_cpufreq_init,
}
static struct cpufreq_driver pxa3xx_cpufreq_driver = {
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = pxa3xx_cpufreq_set,
.init = pxa3xx_cpufreq_init,
}
static struct cpufreq_driver s3c2416_cpufreq_driver = {
- .flags = 0,
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = s3c2416_cpufreq_set_target,
.get = s3c2416_cpufreq_get_speed,
#include <linux/err.h>
#include <linux/io.h>
-#include <mach/hardware.h>
-
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
* specified in @cfg. The values are stored in @cfg for later use
* by the relevant set routine if the request settings can be reached.
*/
-int s3c2440_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
+static int s3c2440_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
{
unsigned int hdiv, pdiv;
unsigned long hclk, fclk, armclk;
return ret;
}
-struct s3c_cpufreq_info s3c2440_cpufreq_info = {
+static struct s3c_cpufreq_info s3c2440_cpufreq_info = {
.max = {
.fclk = 400000000,
.hclk = 133333333,
return -EINVAL;
}
-static unsigned int s3c_cpufreq_get(unsigned int cpu)
-{
- return clk_get_rate(clk_arm) / 1000;
-}
-
struct clk *s3c_cpufreq_clk_get(struct device *dev, const char *name)
{
struct clk *clk;
static int s3c_cpufreq_init(struct cpufreq_policy *policy)
{
+ policy->clk = clk_arm;
return cpufreq_generic_init(policy, ftab, cpu_cur.info->latency);
}
{
suspend_pll.frequency = clk_get_rate(_clk_mpll);
suspend_pll.driver_data = __raw_readl(S3C2410_MPLLCON);
- suspend_freq = s3c_cpufreq_get(0) * 1000;
+ suspend_freq = clk_get_rate(clk_arm);
return 0;
}
#endif
static struct cpufreq_driver s3c24xx_driver = {
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.target = s3c_cpufreq_target,
- .get = s3c_cpufreq_get,
+ .get = cpufreq_generic_get,
.init = s3c_cpufreq_init,
.suspend = s3c_cpufreq_suspend,
.resume = s3c_cpufreq_resume,
return 0;
}
-int __init s3c_cpufreq_auto_io(void)
+static int __init s3c_cpufreq_auto_io(void)
{
int ret;
#include <linux/regulator/consumer.h>
#include <linux/module.h>
-static struct clk *armclk;
static struct regulator *vddarm;
static unsigned long regulator_latency;
};
#endif
-static unsigned int s3c64xx_cpufreq_get_speed(unsigned int cpu)
-{
- if (cpu != 0)
- return 0;
-
- return clk_get_rate(armclk) / 1000;
-}
-
static int s3c64xx_cpufreq_set_target(struct cpufreq_policy *policy,
unsigned int index)
{
unsigned int old_freq, new_freq;
int ret;
- old_freq = clk_get_rate(armclk) / 1000;
+ old_freq = clk_get_rate(policy->clk) / 1000;
new_freq = s3c64xx_freq_table[index].frequency;
dvfs = &s3c64xx_dvfs_table[s3c64xx_freq_table[index].driver_data];
}
#endif
- ret = clk_set_rate(armclk, new_freq * 1000);
+ ret = clk_set_rate(policy->clk, new_freq * 1000);
if (ret < 0) {
pr_err("Failed to set rate %dkHz: %d\n",
new_freq, ret);
if (ret != 0) {
pr_err("Failed to set VDDARM for %dkHz: %d\n",
new_freq, ret);
- if (clk_set_rate(armclk, old_freq * 1000) < 0)
+ if (clk_set_rate(policy->clk, old_freq * 1000) < 0)
pr_err("Failed to restore original clock rate\n");
return ret;
#endif
pr_debug("Set actual frequency %lukHz\n",
- clk_get_rate(armclk) / 1000);
+ clk_get_rate(policy->clk) / 1000);
return 0;
}
return -ENODEV;
}
- armclk = clk_get(NULL, "armclk");
- if (IS_ERR(armclk)) {
+ policy->clk = clk_get(NULL, "armclk");
+ if (IS_ERR(policy->clk)) {
pr_err("Unable to obtain ARMCLK: %ld\n",
- PTR_ERR(armclk));
- return PTR_ERR(armclk);
+ PTR_ERR(policy->clk));
+ return PTR_ERR(policy->clk);
}
#ifdef CONFIG_REGULATOR
unsigned long r;
/* Check for frequencies we can generate */
- r = clk_round_rate(armclk, freq->frequency * 1000);
+ r = clk_round_rate(policy->clk, freq->frequency * 1000);
r /= 1000;
if (r != freq->frequency) {
pr_debug("%dkHz unsupported by clock\n",
/* If we have no regulator then assume startup
* frequency is the maximum we can support. */
- if (!vddarm && freq->frequency > s3c64xx_cpufreq_get_speed(0))
+ if (!vddarm && freq->frequency > clk_get_rate(policy->clk) / 1000)
freq->frequency = CPUFREQ_ENTRY_INVALID;
freq++;
pr_err("Failed to configure frequency table: %d\n",
ret);
regulator_put(vddarm);
- clk_put(armclk);
+ clk_put(policy->clk);
}
return ret;
}
static struct cpufreq_driver s3c64xx_cpufreq_driver = {
- .flags = 0,
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = s3c64xx_cpufreq_set_target,
- .get = s3c64xx_cpufreq_get_speed,
+ .get = cpufreq_generic_get,
.init = s3c64xx_cpufreq_driver_init,
.name = "s3c",
};
#include <mach/map.h>
#include <mach/regs-clock.h>
-static struct clk *cpu_clk;
static struct clk *dmc0_clk;
static struct clk *dmc1_clk;
static DEFINE_MUTEX(set_freq_lock);
__raw_writel(tmp1, reg);
}
-static unsigned int s5pv210_getspeed(unsigned int cpu)
-{
- if (cpu)
- return 0;
-
- return clk_get_rate(cpu_clk) / 1000;
-}
-
static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
{
unsigned long reg;
goto exit;
}
- old_freq = s5pv210_getspeed(0);
+ old_freq = policy->cur;
new_freq = s5pv210_freq_table[index].frequency;
/* Finding current running level index */
unsigned long mem_type;
int ret;
- cpu_clk = clk_get(NULL, "armclk");
- if (IS_ERR(cpu_clk))
- return PTR_ERR(cpu_clk);
+ policy->clk = clk_get(NULL, "armclk");
+ if (IS_ERR(policy->clk))
+ return PTR_ERR(policy->clk);
dmc0_clk = clk_get(NULL, "sclk_dmc0");
if (IS_ERR(dmc0_clk)) {
out_dmc1:
clk_put(dmc0_clk);
out_dmc0:
- clk_put(cpu_clk);
+ clk_put(policy->clk);
return ret;
}
}
static struct cpufreq_driver s5pv210_driver = {
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = s5pv210_target,
- .get = s5pv210_getspeed,
+ .get = cpufreq_generic_get,
.init = s5pv210_cpu_init,
.name = "s5pv210",
#ifdef CONFIG_PM
}
static struct cpufreq_driver sa1100_driver __refdata = {
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = sa1100_target,
.get = sa11x0_getspeed,
/* sa1110_driver needs __refdata because it must remain after init registers
* it with cpufreq_register_driver() */
static struct cpufreq_driver sa1110_driver __refdata = {
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = sa1110_target,
.get = sa11x0_getspeed,
u32 cnt;
} spear_cpufreq;
-static unsigned int spear_cpufreq_get(unsigned int cpu)
-{
- return clk_get_rate(spear_cpufreq.clk) / 1000;
-}
-
static struct clk *spear1340_cpu_get_possible_parent(unsigned long newfreq)
{
struct clk *sys_pclk;
}
newfreq = clk_round_rate(srcclk, newfreq * mult);
- if (newfreq < 0) {
+ if (newfreq <= 0) {
pr_err("clk_round_rate failed for cpu src clock\n");
return newfreq;
}
static int spear_cpufreq_init(struct cpufreq_policy *policy)
{
+ policy->clk = spear_cpufreq.clk;
return cpufreq_generic_init(policy, spear_cpufreq.freq_tbl,
spear_cpufreq.transition_latency);
}
static struct cpufreq_driver spear_cpufreq_driver = {
.name = "cpufreq-spear",
- .flags = CPUFREQ_STICKY,
+ .flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = spear_cpufreq_target,
- .get = spear_cpufreq_get,
+ .get = cpufreq_generic_get,
.init = spear_cpufreq_init,
.exit = cpufreq_generic_exit,
.attr = cpufreq_generic_attr,
pr_debug("previous speed is %u\n", prev_speed);
+ preempt_disable();
local_irq_save(flags);
/* switch to low state */
out:
local_irq_restore(flags);
+ preempt_enable();
+
return ret;
}
EXPORT_SYMBOL_GPL(speedstep_get_freqs);
return result;
}
-/**
- * speedstep_get_state - set the SpeedStep state
- * @state: processor frequency state (SPEEDSTEP_LOW or SPEEDSTEP_HIGH)
- *
- */
-static int speedstep_get_state(void)
-{
- u32 function = GET_SPEEDSTEP_STATE;
- u32 result, state, edi, command, dummy;
-
- command = (smi_sig & 0xffffff00) | (smi_cmd & 0xff);
-
- pr_debug("trying to determine current setting with command %x "
- "at port %x\n", command, smi_port);
-
- __asm__ __volatile__(
- "push %%ebp\n"
- "out %%al, (%%dx)\n"
- "pop %%ebp\n"
- : "=a" (result),
- "=b" (state), "=D" (edi),
- "=c" (dummy), "=d" (dummy), "=S" (dummy)
- : "a" (command), "b" (function), "c" (0),
- "d" (smi_port), "S" (0), "D" (0)
- );
-
- pr_debug("state is %x, result is %x\n", state, result);
-
- return state & 1;
-}
-
-
/**
* speedstep_set_state - set the SpeedStep state
* @state: new processor frequency state (SPEEDSTEP_LOW or SPEEDSTEP_HIGH)
return;
/* Disable IRQs */
+ preempt_disable();
local_irq_save(flags);
command = (smi_sig & 0xffffff00) | (smi_cmd & 0xff);
do {
if (retry) {
+ /*
+ * We need to enable interrupts, otherwise the blockage
+ * won't resolve.
+ *
+ * We disable preemption so that other processes don't
+ * run. If other processes were running, they could
+ * submit more DMA requests, making the blockage worse.
+ */
pr_debug("retry %u, previous result %u, waiting...\n",
retry, result);
+ local_irq_enable();
mdelay(retry * 50);
+ local_irq_disable();
}
retry++;
__asm__ __volatile__(
/* enable IRQs */
local_irq_restore(flags);
+ preempt_enable();
if (new_state == state)
pr_debug("change to %u MHz succeeded after %u tries "
static struct clk *pll_p_clk;
static struct clk *emc_clk;
-static unsigned long target_cpu_speed[NUM_CPUS];
static DEFINE_MUTEX(tegra_cpu_lock);
static bool is_suspended;
-static unsigned int tegra_getspeed(unsigned int cpu)
-{
- unsigned long rate;
-
- if (cpu >= NUM_CPUS)
- return 0;
-
- rate = clk_get_rate(cpu_clk) / 1000;
- return rate;
-}
-
static int tegra_cpu_clk_set_rate(unsigned long rate)
{
int ret;
{
int ret = 0;
- if (tegra_getspeed(0) == rate)
- return ret;
-
/*
* Vote on memory bus frequency based on cpu frequency
* This sets the minimum frequency, display or avp may request higher
return ret;
}
-static unsigned long tegra_cpu_highest_speed(void)
-{
- unsigned long rate = 0;
- int i;
-
- for_each_online_cpu(i)
- rate = max(rate, target_cpu_speed[i]);
- return rate;
-}
-
static int tegra_target(struct cpufreq_policy *policy, unsigned int index)
{
- unsigned int freq;
- int ret = 0;
+ int ret = -EBUSY;
mutex_lock(&tegra_cpu_lock);
- if (is_suspended)
- goto out;
-
- freq = freq_table[index].frequency;
+ if (!is_suspended)
+ ret = tegra_update_cpu_speed(policy,
+ freq_table[index].frequency);
- target_cpu_speed[policy->cpu] = freq;
-
- ret = tegra_update_cpu_speed(policy, tegra_cpu_highest_speed());
-
-out:
mutex_unlock(&tegra_cpu_lock);
return ret;
}
is_suspended = true;
pr_info("Tegra cpufreq suspend: setting frequency to %d kHz\n",
freq_table[0].frequency);
- tegra_update_cpu_speed(policy, freq_table[0].frequency);
+ if (clk_get_rate(cpu_clk) / 1000 != freq_table[0].frequency)
+ tegra_update_cpu_speed(policy, freq_table[0].frequency);
cpufreq_cpu_put(policy);
} else if (event == PM_POST_SUSPEND) {
is_suspended = false;
clk_prepare_enable(emc_clk);
clk_prepare_enable(cpu_clk);
- target_cpu_speed[policy->cpu] = tegra_getspeed(policy->cpu);
-
/* FIXME: what's the actual transition time? */
ret = cpufreq_generic_init(policy, freq_table, 300 * 1000);
if (ret) {
if (policy->cpu == 0)
register_pm_notifier(&tegra_cpu_pm_notifier);
+ policy->clk = cpu_clk;
return 0;
}
}
static struct cpufreq_driver tegra_cpufreq_driver = {
+ .flags = CPUFREQ_NEED_INITIAL_FREQ_CHECK,
.verify = cpufreq_generic_frequency_table_verify,
.target_index = tegra_target,
- .get = tegra_getspeed,
+ .get = cpufreq_generic_get,
.init = tegra_cpu_init,
.exit = tegra_cpu_exit,
.name = "tegra",
* published by the Free Software Foundation.
*/
+#include <linux/err.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/init.h>
return 0;
}
-static unsigned int ucv2_getspeed(unsigned int cpu)
-{
- struct clk *mclk = clk_get(NULL, "MAIN_CLK");
-
- if (cpu)
- return 0;
- return clk_get_rate(mclk)/1000;
-}
-
static int ucv2_target(struct cpufreq_policy *policy,
unsigned int target_freq,
unsigned int relation)
{
- unsigned int cur = ucv2_getspeed(0);
struct cpufreq_freqs freqs;
- struct clk *mclk = clk_get(NULL, "MAIN_CLK");
+ int ret;
- cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
+ freqs.old = policy->cur;
+ freqs.new = target_freq;
- if (!clk_set_rate(mclk, target_freq * 1000)) {
- freqs.old = cur;
- freqs.new = target_freq;
- }
-
- cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
+ cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
+ ret = clk_set_rate(policy->mclk, target_freq * 1000);
+ cpufreq_notify_post_transition(policy, &freqs, ret);
- return 0;
+ return ret;
}
static int __init ucv2_cpu_init(struct cpufreq_policy *policy)
{
if (policy->cpu != 0)
return -EINVAL;
+
policy->min = policy->cpuinfo.min_freq = 250000;
policy->max = policy->cpuinfo.max_freq = 1000000;
policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
+ policy->clk = clk_get(NULL, "MAIN_CLK");
+ if (IS_ERR(policy->clk))
+ return PTR_ERR(policy->clk);
return 0;
}
.flags = CPUFREQ_STICKY,
.verify = ucv2_verify_speed,
.target = ucv2_target,
- .get = ucv2_getspeed,
+ .get = cpufreq_generic_get,
.init = ucv2_cpu_init,
.name = "UniCore-II",
};
#ifndef _LINUX_CPUFREQ_H
#define _LINUX_CPUFREQ_H
+#include <linux/clk.h>
#include <linux/cpumask.h>
#include <linux/completion.h>
#include <linux/kobject.h>
unsigned int cpu; /* cpu nr of CPU managing this policy */
unsigned int last_cpu; /* cpu nr of previous CPU that managed
* this policy */
+ struct clk *clk;
struct cpufreq_cpuinfo cpuinfo;/* see above */
unsigned int min; /* in kHz */
*/
#define CPUFREQ_ASYNC_NOTIFICATION (1 << 4)
+/*
+ * Set by drivers which want cpufreq core to check if CPU is running at a
+ * frequency present in freq-table exposed by the driver. For these drivers if
+ * CPU is found running at an out of table freq, we will try to set it to a freq
+ * from the table. And if that fails, we will stop further boot process by
+ * issuing a BUG_ON().
+ */
+#define CPUFREQ_NEED_INITIAL_FREQ_CHECK (1 << 5)
+
int cpufreq_register_driver(struct cpufreq_driver *driver_data);
int cpufreq_unregister_driver(struct cpufreq_driver *driver_data);
#define CPUFREQ_NOTIFY (2)
#define CPUFREQ_START (3)
#define CPUFREQ_UPDATE_POLICY_CPU (4)
+#define CPUFREQ_CREATE_POLICY (5)
+#define CPUFREQ_REMOVE_POLICY (6)
#ifdef CONFIG_CPU_FREQ
int cpufreq_register_notifier(struct notifier_block *nb, unsigned int list);
void cpufreq_notify_transition(struct cpufreq_policy *policy,
struct cpufreq_freqs *freqs, unsigned int state);
+void cpufreq_notify_post_transition(struct cpufreq_policy *policy,
+ struct cpufreq_freqs *freqs, int transition_failed);
#else /* CONFIG_CPU_FREQ */
static inline int cpufreq_register_notifier(struct notifier_block *nb,
unsigned int target_freq,
unsigned int relation,
unsigned int *index);
+int cpufreq_frequency_table_get_index(struct cpufreq_policy *policy,
+ unsigned int freq);
void cpufreq_frequency_table_update_policy_cpu(struct cpufreq_policy *policy);
ssize_t cpufreq_show_cpus(const struct cpumask *mask, char *buf);
int cpufreq_table_validate_and_show(struct cpufreq_policy *policy,
struct cpufreq_frequency_table *table);
+unsigned int cpufreq_generic_get(unsigned int cpu);
int cpufreq_generic_init(struct cpufreq_policy *policy,
struct cpufreq_frequency_table *table,
unsigned int transition_latency);
projects / karo-tx-linux.git / commitdiff