This can be used to load and uncompress arbitrary
data.
+ fdt_high - if set this restricts the maximum address that the
+ flattened device tree will be copied into upon boot.
+ If this is set to the special value 0xFFFFFFFF then
+ the fdt will not be copied at all on boot. For this
+ to work it must reside in writable memory, have
+ sufficient padding on the end of it for u-boot to
+ add the information it needs into it, and the memory
+ must be accessible by the kernel.
+
i2cfast - (PPC405GP|PPC405EP only)
if set to 'y' configures Linux I2C driver for fast
mode (400kHZ). This environment variable is used in
CPU_TYPE_ENTRY(P1016, P1016_E, 1),
CPU_TYPE_ENTRY(P1016, P1016, 1),
CPU_TYPE_ENTRY(P1017, P1017, 1),
- CPU_TYPE_ENTRY(P1017, P1017, 1),
+ CPU_TYPE_ENTRY(P1017, P1017_E, 1),
CPU_TYPE_ENTRY(P1020, P1020, 2),
CPU_TYPE_ENTRY(P1020, P1020_E, 2),
CPU_TYPE_ENTRY(P1021, P1021, 2),
--- /dev/null
+#
+# Copyright 2011 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y += $(BOARD).o
+COBJS-y += cpld.o
+COBJS-y += ddr.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+COBJS-$(CONFIG_PCI) += pci.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/**
+ * Copyright 2011 Freescale Semiconductor
+ * Author: Mingkai Hu <Mingkai.hu@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This file provides support for the board-specific CPLD used on some Freescale
+ * reference boards.
+ *
+ * The following macros need to be defined:
+ *
+ * CPLD_BASE - The virtual address of the base of the CPLD register map
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+
+#include "cpld.h"
+
+static u8 __cpld_read(unsigned int reg)
+{
+ void *p = (void *)CPLD_BASE;
+
+ return in_8(p + reg);
+}
+u8 cpld_read(unsigned int reg) __attribute__((weak, alias("__cpld_read")));
+
+static void __cpld_write(unsigned int reg, u8 value)
+{
+ void *p = (void *)CPLD_BASE;
+
+ out_8(p + reg, value);
+}
+void cpld_write(unsigned int reg, u8 value)
+ __attribute__((weak, alias("__cpld_write")));
+
+/*
+ * Reset the board. This honors the por_cfg registers.
+ */
+void __cpld_reset(void)
+{
+ CPLD_WRITE(system_rst, 1);
+}
+void cpld_reset(void) __attribute__((weak, alias("__cpld_reset")));
+
+/**
+ * Set the boot bank to the alternate bank
+ */
+void __cpld_set_altbank(void)
+{
+ CPLD_WRITE(fbank_sel, 1);
+}
+void cpld_set_altbank(void)
+ __attribute__((weak, alias("__cpld_set_altbank")));
+
+/**
+ * Set the boot bank to the default bank
+ */
+void __cpld_clear_altbank(void)
+{
+ CPLD_WRITE(fbank_sel, 0);
+}
+void cpld_clear_altbank(void)
+ __attribute__((weak, alias("__cpld_clear_altbank")));
+
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+ printf("cpld_ver = 0x%02x\n", CPLD_READ(cpld_ver));
+ printf("cpld_ver_sub = 0x%02x\n", CPLD_READ(cpld_ver_sub));
+ printf("pcba_ver = 0x%02x\n", CPLD_READ(pcba_ver));
+ printf("system_rst = 0x%02x\n", CPLD_READ(system_rst));
+ printf("wd_cfg = 0x%02x\n", CPLD_READ(wd_cfg));
+ printf("sw_ctl_on = 0x%02x\n", CPLD_READ(sw_ctl_on));
+ printf("por_cfg = 0x%02x\n", CPLD_READ(por_cfg));
+ printf("switch_strobe = 0x%02x\n", CPLD_READ(switch_strobe));
+ printf("jtag_sel = 0x%02x\n", CPLD_READ(jtag_sel));
+ printf("sdbank1_clk = 0x%02x\n", CPLD_READ(sdbank1_clk));
+ printf("sdbank2_clk = 0x%02x\n", CPLD_READ(sdbank2_clk));
+ printf("fbank_sel = 0x%02x\n", CPLD_READ(fbank_sel));
+ printf("serdes_mux = 0x%02x\n", CPLD_READ(serdes_mux));
+ printf("SW[2] = 0x%02x\n", in_8(&CPLD_SW(2)));
+ putc('\n');
+}
+#endif
+
+int cpld_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+ unsigned int i;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (strcmp(argv[2], "altbank") == 0)
+ cpld_set_altbank();
+ else
+ cpld_clear_altbank();
+
+ cpld_reset();
+ } else if (strcmp(argv[1], "watchdog") == 0) {
+ static char *period[8] = {"1ms", "10ms", "30ms", "disable",
+ "100ms", "1s", "10s", "60s"};
+ for (i = 0; i < ARRAY_SIZE(period); i++) {
+ if (strcmp(argv[2], period[i]) == 0)
+ CPLD_WRITE(wd_cfg, i);
+ }
+ } else if (strcmp(argv[1], "lane_mux") == 0) {
+ u32 lane = simple_strtoul(argv[2], NULL, 16);
+ u8 val = (u8)simple_strtoul(argv[3], NULL, 16);
+ u8 reg = CPLD_READ(serdes_mux);
+
+ switch (lane) {
+ case 0x6:
+ reg &= ~SERDES_MUX_LANE_6_MASK;
+ reg |= val << SERDES_MUX_LANE_6_SHIFT;
+ break;
+ case 0xa:
+ reg &= ~SERDES_MUX_LANE_A_MASK;
+ reg |= val << SERDES_MUX_LANE_A_SHIFT;
+ break;
+ case 0xc:
+ reg &= ~SERDES_MUX_LANE_C_MASK;
+ reg |= val << SERDES_MUX_LANE_C_SHIFT;
+ break;
+ case 0xd:
+ reg &= ~SERDES_MUX_LANE_D_MASK;
+ reg |= val << SERDES_MUX_LANE_D_SHIFT;
+ break;
+ default:
+ printf("Invalid value\n");
+ break;
+ }
+
+ CPLD_WRITE(serdes_mux, reg);
+#ifdef DEBUG
+ } else if (strcmp(argv[1], "dump") == 0) {
+ cpld_dump_regs();
+#endif
+ } else
+ rc = cmd_usage(cmdtp);
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld_cmd, CONFIG_SYS_MAXARGS, 1, cpld_cmd,
+ "Reset the board or pin mulexing selection using the CPLD sequencer",
+ "reset - hard reset to default bank\n"
+ "cpld_cmd reset altbank - reset to alternate bank\n"
+ "cpld_cmd watchdog <watchdog_period> - set the watchdog period\n"
+ " period: 1ms 10ms 30ms 100ms 1s 10s 60s disable\n"
+ "cpld_cmd lane_mux <lane> <mux_value> - set multiplexed lane pin\n"
+ " lane 6: 0 -> slot1 (Default)\n"
+ " 1 -> SGMII\n"
+ " lane a: 0 -> slot2 (Default)\n"
+ " 1 -> AURORA\n"
+ " lane c: 0 -> slot2 (Default)\n"
+ " 1 -> SATA0\n"
+ " lane d: 0 -> slot2 (Default)\n"
+ " 1 -> SATA1\n"
+#ifdef DEBUG
+ "cpld_cmd dump - display the CPLD registers\n"
+#endif
+ );
--- /dev/null
+/**
+ * Copyright 2011 Freescale Semiconductor
+ * Author: Mingkai Hu <Mingkai.hu@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This file provides support for the ngPIXIS, a board-specific FPGA used on
+ * some Freescale reference boards.
+ */
+
+/*
+ * CPLD register set. Feel free to add board-specific #ifdefs where necessary.
+ */
+typedef struct cpld_data {
+ u8 cpld_ver; /* 0x0 - CPLD Major Revision Register */
+ u8 cpld_ver_sub; /* 0x1 - CPLD Minor Revision Register */
+ u8 pcba_ver; /* 0x2 - PCBA Revision Register */
+ u8 system_rst; /* 0x3 - system reset register */
+ u8 wd_cfg; /* 0x4 - Watchdog Period Setting Register */
+ u8 sw_ctl_on; /* 0x5 - Switch Control Enable Register */
+ u8 por_cfg; /* 0x6 - POR Control Register */
+ u8 switch_strobe; /* 0x7 - Multiplexed pin Select Register */
+ u8 jtag_sel; /* 0x8 - JTAG or AURORA Selection */
+ u8 sdbank1_clk; /* 0x9 - SerDes Bank1 Reference clock */
+ u8 sdbank2_clk; /* 0xa - SerDes Bank2 Reference clock */
+ u8 fbank_sel; /* 0xb - Flash bank selection */
+ u8 serdes_mux; /* 0xc - Multiplexed pin Select Register */
+ u8 sw[1]; /* 0xd - SW2 Status */
+} __attribute__ ((packed)) cpld_data_t;
+
+#define SERDES_MUX_LANE_6_MASK 0x2
+#define SERDES_MUX_LANE_6_SHIFT 1
+#define SERDES_MUX_LANE_A_MASK 0x1
+#define SERDES_MUX_LANE_A_SHIFT 0
+#define SERDES_MUX_LANE_C_MASK 0x4
+#define SERDES_MUX_LANE_C_SHIFT 2
+#define SERDES_MUX_LANE_D_MASK 0x8
+#define SERDES_MUX_LANE_D_SHIFT 3
+
+/* Pointer to the CPLD register set */
+#define cpld ((cpld_data_t *)CPLD_BASE)
+
+/* The CPLD SW register that corresponds to board switch X, where x >= 1 */
+#define CPLD_SW(x) (cpld->sw[(x) - 2])
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(cpld_data_t, reg))
+#define CPLD_WRITE(reg, value) cpld_write(offsetof(cpld_data_t, reg), value)
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+typedef struct {
+ u32 datarate_mhz_low;
+ u32 datarate_mhz_high;
+ u32 n_ranks;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2T;
+} board_specific_parameters_t;
+
+/*
+ * ranges for parameters:
+ * wr_data_delay = 0-6
+ * clk adjust = 0-8
+ * cpo 2-0x1E (30)
+ */
+const board_specific_parameters_t board_specific_parameters[] = {
+ /*
+ * memory controller 0
+ * lo| hi| num| clk| wrlvl | cpo |wrdata|2T
+ * mhz| mhz|ranks|adjst| start | delay|
+ */
+ { 1017, 1116, 2, 4, 6, 0xff, 2, 0},
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const board_specific_parameters_t *pbsp =
+ &board_specific_parameters[0];
+ u32 num_params = ARRAY_SIZE(board_specific_parameters);
+ u32 i;
+ ulong ddr_freq;
+
+ /*
+ * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ for (i = 0; i < num_params; i++) {
+ if (ddr_freq >= pbsp->datarate_mhz_low &&
+ ddr_freq <= pbsp->datarate_mhz_high &&
+ pdimm[0].n_ranks == pbsp->n_ranks) {
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay = pbsp->write_data_delay;
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->twoT_en = pbsp->force_2T;
+ break;
+ }
+ pbsp++;
+ }
+
+ if (i == num_params) {
+ printf("Warning: board specific timing not found "
+ "for data rate %lu MT/s!\n", ddr_freq);
+ }
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /* Write leveling override */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /* Rtt and Rtt_WR override */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 60 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN;
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size = 0;
+
+ puts("Initializing....");
+
+ if (fsl_use_spd()) {
+ puts("using SPD\n");
+ dram_size = fsl_ddr_sdram();
+ } else {
+ puts("no SPD and fixed parameters\n");
+ return dram_size;
+ }
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ puts(" DDR: ");
+ return dram_size;
+}
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
+ SET_LAW(CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+extern void pci_of_setup(void *blob, bd_t *bd);
+
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ u8 sw;
+ struct cpu_type *cpu = gd->cpu;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+ unsigned int i;
+
+ printf("Board: %sRDB, ", cpu->name);
+ printf("CPLD version: %d.%d ", CPLD_READ(cpld_ver),
+ CPLD_READ(cpld_ver_sub));
+
+ sw = CPLD_READ(fbank_sel);
+ printf("vBank: %d\n", sw & 0x1);
+
+#ifdef CONFIG_PHYS_64BIT
+ puts("36-bit Addressing\n");
+#endif
+
+ /*
+ * Display the RCW, so that no one gets confused as to what RCW
+ * we're actually using for this boot.
+ */
+ puts("Reset Configuration Word (RCW):");
+ for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
+ u32 rcw = in_be32(&gur->rcwsr[i]);
+
+ if ((i % 4) == 0)
+ printf("\n %08x:", i * 4);
+ printf(" %08x", rcw);
+ }
+ puts("\n");
+
+ /*
+ * Display the actual SERDES reference clocks as configured by the
+ * dip switches on the board. Note that the SWx registers could
+ * technically be set to force the reference clocks to match the
+ * values that the SERDES expects (or vice versa). For now, however,
+ * we just display both values and hope the user notices when they
+ * don't match.
+ */
+ puts("SERDES Reference Clocks: ");
+ sw = in_8(&CPLD_SW(2)) >> 2;
+ for (i = 0; i < 2; i++) {
+ static const char * const freq[] = {"0", "100", "125"};
+ unsigned int clock = (sw >> (2 * i)) & 3;
+
+ printf("Bank%u=%sMhz ", i+1, freq[clock]);
+ }
+ puts("\n");
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ /* board only uses the DDR_MCK0/1, so disable the DDR_MCK2/3 */
+ setbits_be32(&gur->ddrclkdr, 0x000f000f);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ set_liodns();
+ setup_portals();
+
+ return 0;
+}
+
+static const char *serdes_clock_to_string(u32 clock)
+{
+ switch (clock) {
+ case SRDS_PLLCR0_RFCK_SEL_100:
+ return "100";
+ case SRDS_PLLCR0_RFCK_SEL_125:
+ return "125";
+ case SRDS_PLLCR0_RFCK_SEL_156_25:
+ return "156.25";
+ default:
+ return "150";
+ }
+}
+
+#define NUM_SRDS_BANKS 2
+
+int misc_init_r(void)
+{
+ serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+ u32 actual[NUM_SRDS_BANKS];
+ unsigned int i;
+ u8 sw;
+
+ sw = in_8(&CPLD_SW(2)) >> 2;
+ for (i = 0; i < NUM_SRDS_BANKS; i++) {
+ unsigned int clock = (sw >> (2 * i)) & 3;
+ switch (clock) {
+ case 1:
+ actual[i] = SRDS_PLLCR0_RFCK_SEL_100;
+ break;
+ case 2:
+ actual[i] = SRDS_PLLCR0_RFCK_SEL_125;
+ break;
+ default:
+ printf("Warning: SDREFCLK%u switch setting of '11' is "
+ "unsupported\n", i + 1);
+ break;
+ }
+ }
+
+ for (i = 0; i < NUM_SRDS_BANKS; i++) {
+ u32 expected = in_be32(®s->bank[i].pllcr0);
+ expected &= SRDS_PLLCR0_RFCK_SEL_MASK;
+ if (expected != actual[i]) {
+ printf("Warning: SERDES bank %u expects reference clock"
+ " %sMHz, but actual is %sMHz\n", i + 1,
+ serdes_clock_to_string(expected),
+ serdes_clock_to_string(actual[i]));
+ }
+ }
+
+ return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+}
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ SET_TLB_ENTRY(0, CPLD_BASE, CPLD_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+ * SRAM is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
+ CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000,
+ CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 11, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_1M, 1),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 13, BOOKE_PAGESZ_4M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
P2020RDB_NAND powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,NAND
P2020RDB_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SDCARD
P2020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2020RDB,SPIFLASH
+P2041RDB powerpc mpc85xx p2041rdb freescale
+P2041RDB_SDCARD powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
+P2041RDB_SPIFLASH powerpc mpc85xx p2041rdb freescale - P2041RDB:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
P3041DS powerpc mpc85xx corenet_ds freescale
P3041DS_NAND powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
P3041DS_SDCARD powerpc mpc85xx corenet_ds freescale - P3041DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
return phandle + 1;
}
+/*
+ * fdt_create_phandle: Create a phandle property for the given node
+ *
+ * @fdt: ptr to device tree
+ * @nodeoffset: node to update
+ * @phandle: phandle value to set (must be unique)
+*/
+int fdt_create_phandle(void *fdt, int nodeoffset, uint32_t phandle)
+{
+ int ret;
+
+#ifdef DEBUG
+ int off = fdt_node_offset_by_phandle(fdt, phandle);
+
+ if ((off >= 0) && (off != nodeoffset)) {
+ char buf[64];
+
+ fdt_get_path(fdt, nodeoffset, buf, sizeof(buf));
+ printf("Trying to update node %s with phandle %u ",
+ buf, phandle);
+
+ fdt_get_path(fdt, off, buf, sizeof(buf));
+ printf("that already exists in node %s.\n", buf);
+ return -FDT_ERR_BADPHANDLE;
+ }
+#endif
+
+ ret = fdt_setprop_cell(fdt, nodeoffset, "phandle", phandle);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * For now, also set the deprecated "linux,phandle" property, so that we
+ * don't break older kernels.
+ */
+ ret = fdt_setprop_cell(fdt, nodeoffset, "linux,phandle", phandle);
+
+ return ret;
+}
+
#if defined(CONFIG_VIDEO)
int fdt_add_edid(void *blob, const char *compat, unsigned char *edid_buf)
{
return ret;
}
#endif
+
+/*
+ * Verify the physical address of device tree node for a given alias
+ *
+ * This function locates the device tree node of a given alias, and then
+ * verifies that the physical address of that device matches the given
+ * parameter. It displays a message if there is a mismatch.
+ *
+ * Returns 1 on success, 0 on failure
+ */
+int fdt_verify_alias_address(void *fdt, int anode, const char *alias, u64 addr)
+{
+ const char *path;
+ const u32 *reg;
+ int node, len;
+ u64 dt_addr;
+
+ path = fdt_getprop(fdt, anode, alias, NULL);
+ if (!path) {
+ /* If there's no such alias, then it's not a failure */
+ return 1;
+ }
+
+ node = fdt_path_offset(fdt, path);
+ if (node < 0) {
+ printf("Warning: device tree alias '%s' points to invalid "
+ "node %s.\n", alias, path);
+ return 0;
+ }
+
+ reg = fdt_getprop(fdt, node, "reg", &len);
+ if (!reg) {
+ printf("Warning: device tree node '%s' has no address.\n",
+ path);
+ return 0;
+ }
+
+ dt_addr = fdt_translate_address(fdt, node, reg);
+ if (addr != dt_addr) {
+ printf("Warning: U-Boot configured device %s at address %llx,\n"
+ " but the device tree has it address %llx.\n",
+ alias, addr, dt_addr);
+ return 0;
+ }
+
+ return 1;
+}
+
+/*
+ * Returns the base address of an SOC or PCI node
+ */
+u64 fdt_get_base_address(void *fdt, int node)
+{
+ int size;
+ u32 naddr;
+ const u32 *prop;
+
+ prop = fdt_getprop(fdt, node, "#address-cells", &size);
+ if (prop && size == 4)
+ naddr = *prop;
+ else
+ naddr = 2;
+
+ prop = fdt_getprop(fdt, node, "ranges", &size);
+
+ return prop ? fdt_translate_address(fdt, node, prop + naddr) : 0;
+}
{
void *fdt_blob = *of_flat_tree;
void *of_start = 0;
+ char *fdt_high;
ulong of_len = 0;
int err;
+ int disable_relocation = 0;
/* nothing to do */
if (*of_size == 0)
/* position on a 4K boundary before the alloc_current */
/* Pad the FDT by a specified amount */
of_len = *of_size + CONFIG_SYS_FDT_PAD;
- of_start = (void *)(unsigned long)lmb_alloc_base(lmb, of_len, 0x1000,
- getenv_bootm_mapsize() + getenv_bootm_low());
+
+ /* If fdt_high is set use it to select the relocation address */
+ fdt_high = getenv("fdt_high");
+ if (fdt_high) {
+ void *desired_addr = (void *)simple_strtoul(fdt_high, NULL, 16);
+
+ if (((ulong) desired_addr) == ~0UL) {
+ /* All ones means use fdt in place */
+ desired_addr = fdt_blob;
+ disable_relocation = 1;
+ }
+ if (desired_addr) {
+ of_start =
+ (void *)(ulong) lmb_alloc_base(lmb, of_len, 0x1000,
+ ((ulong)
+ desired_addr)
+ + of_len);
+ if (desired_addr && of_start != desired_addr) {
+ puts("Failed using fdt_high value for Device Tree");
+ goto error;
+ }
+ } else {
+ of_start =
+ (void *)(ulong) mb_alloc(lmb, of_len, 0x1000);
+ }
+ } else {
+ of_start =
+ (void *)(ulong) lmb_alloc_base(lmb, of_len, 0x1000,
+ getenv_bootm_mapsize()
+ + getenv_bootm_low());
+ }
if (of_start == 0) {
puts("device tree - allocation error\n");
goto error;
}
- debug ("## device tree at %p ... %p (len=%ld [0x%lX])\n",
- fdt_blob, fdt_blob + *of_size - 1, of_len, of_len);
+ if (disable_relocation) {
+ /* We assume there is space after the existing fdt to use for padding */
+ fdt_set_totalsize(of_start, of_len);
+ printf(" Using Device Tree in place at %p, end %p\n",
+ of_start, of_start + of_len - 1);
+ } else {
+ debug ("## device tree at %p ... %p (len=%ld [0x%lX])\n",
+ fdt_blob, fdt_blob + *of_size - 1, of_len, of_len);
- printf (" Loading Device Tree to %p, end %p ... ",
- of_start, of_start + of_len - 1);
+ printf (" Loading Device Tree to %p, end %p ... ",
+ of_start, of_start + of_len - 1);
- err = fdt_open_into (fdt_blob, of_start, of_len);
- if (err != 0) {
- fdt_error ("fdt move failed");
- goto error;
+ err = fdt_open_into (fdt_blob, of_start, of_len);
+ if (err != 0) {
+ fdt_error ("fdt move failed");
+ goto error;
+ }
+ puts ("OK\n");
}
- puts ("OK\n");
*of_flat_tree = of_start;
*of_size = of_len;
--- /dev/null
+Overview
+=========
+The P2041 Processor combines four Power Architecture processor cores
+with high-performance datapath acceleration architecture(DPAA), CoreNet
+fabric infrastructure, as well as network and peripheral bus interfaces
+required for networking, telecom/datacom, wireless infrastructure, and
+military/aerospace applications.
+
+P2041RDB board is a quad core platform supporting the P2041 processor
+of QorIQ DPAA series.
+
+Boot from NOR flash
+===================
+1. Build image
+ make P2041RDB_config
+ make all
+
+2. Program image
+ => tftp 1000000 u-boot.bin
+ => protect off all
+ => erase eff80000 efffffff
+ => cp.b 1000000 eff80000 80000
+
+3. Program RCW
+ => tftp 1000000 rcw.bin
+ => protect off all
+ => erase e8000000 e801ffff
+ => cp.b 1000000 e8000000 50
+
+4. Program FMAN Firmware ucode
+ => tftp 1000000 ucode.bin
+ => protect off all
+ => erase ef000000 ef0fffff
+ => cp.b 1000000 ef000000 2000
+
+5. Change DIP-switch
+ SW1[1-5] = 10110
+ Note: 1 stands for 'on', 0 stands for 'off'
+
+Boot from SDCard
+===================
+1. Build image
+ make P2041RDB_SDCARD_config
+ make all
+
+2. Generate PBL imge
+ Use PE tool to produce a image used to be programed to
+ SDCard which contains RCW and U-Boot image.
+
+3. Program the PBL image to SDCard
+ => tftp 1000000 pbl_sd.bin
+ => mmcinfo
+ => mmc write 1000000 8 441
+
+4. Program FMAN Firmware ucode
+ => tftp 1000000 ucode.bin
+ => mmc write 1000000 46a 10
+
+5. Change DIP-switch
+ SW1[1-5] = 01100
+ Note: 1 stands for 'on', 0 stands for 'off'
+
+Boot from SPI flash
+===================
+1. Build image
+ make P2041RDB_SPIFLASH_config
+ make all
+
+2. Generate PBL imge
+ Use PE tool to produce a image used to be programed to
+ SPI flash which contains RCW and U-Boot image.
+
+3. Program the PBL image to SPI flash
+ => tftp 1000000 pbl_spi.bin
+ => spi probe 0
+ => sf erase 0 100000
+ => sf write 1000000 0 $filesize
+
+4. Program FMAN Firmware ucode
+ => tftp 1000000 ucode.bin
+ => sf erase 110000 10000
+ => sf write 1000000 110000 $filesize
+
+5. Change DIP-switch
+ SW1[1-5] = 10100
+ Note: 1 stands for 'on', 0 stands for 'off'
+
+CPLD command
+============
+The CPLD is used to control the power sequence and some serdes lane
+mux function.
+
+cpld reset - hard reset to default bank
+cpld reset altbank - reset to alternate bank
+cpld lane_mux <lane> <mux_value> - set multiplexed lane pin
+ lane 6: 0 -> slot1 (Default)
+ 1 -> SGMII
+ lane a: 0 -> slot2 (Default)
+ 1 -> AURORA
+ lane c: 0 -> slot2 (Default)
+ 1 -> SATA0
+ lane d: 0 -> slot2 (Default)
+ 1 -> SATA1
+
+Using the Device Tree Source File
+=================================
+To create the DTB (Device Tree Binary) image file, use a command
+similar to this:
+ dtc -O dtb -b 0 -p 1024 p2041rdb.dts > p2041rdb.dtb
+
+Or use the following command:
+ {linux-2.6}/make p2041rdb.dtb ARCH=powerpc
+
+then the dtb file will be generated under the following directory:
+ {linux-2.6}/arch/powerpc/boot/p2041rdb.dtb
+
+Booting Linux
+=============
+Place a linux uImage in the TFTP disk area.
+ tftp 1000000 uImage
+ tftp 2000000 rootfs.ext2.gz.uboot
+ tftp 3000000 p2041rdb.dtb
+ bootm 1000000 2000000 3000000
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
-#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * P2041 RDB board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_P2041RDB
+#define CONFIG_PHYS_64BIT
+#define CONFIG_PPC_P2041
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */
+#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
+#define CONFIG_MP /* support multiple processors */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#define CONFIG_SYS_SRIO
+#define CONFIG_SRIO1 /* SRIO port 1 */
+#define CONFIG_SRIO2 /* SRIO port 2 */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+ #define CONFIG_SYS_EXTRA_ENV_RELOC
+ #define CONFIG_ENV_IS_IN_SPI_FLASH
+ #define CONFIG_ENV_SPI_BUS 0
+ #define CONFIG_ENV_SPI_CS 0
+ #define CONFIG_ENV_SPI_MAX_HZ 10000000
+ #define CONFIG_ENV_SPI_MODE 0
+ #define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+ #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+ #define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+ #define CONFIG_SYS_EXTRA_ENV_RELOC
+ #define CONFIG_ENV_IS_IN_MMC
+ #define CONFIG_SYS_MMC_ENV_DEV 0
+ #define CONFIG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_OFFSET (512 * 1097)
+#else
+ #define CONFIG_ENV_IS_IN_FLASH
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \
+ - CONFIG_ENV_SECT_SIZE)
+ #define CONFIG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_SYS_CLK_FREQ 66666666
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB /* toggle branch predition */
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
+ CONFIG_RAMBOOT_TEXT_BASE)
+#else
+#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR
+#endif
+#define CONFIG_SYS_L3_SIZE (1024 << 10)
+#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xfe000000 /* relocated CCSRBAR */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS 0xffe000000ull
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
+#endif
+/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_FSL_DDR3
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x52
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+/*
+ * Local Bus Definitions
+ */
+
+/* Set the local bus clock 1/8 of platform clock */
+#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8
+
+#define CONFIG_SYS_FLASH_BASE 0xe8000000 /* Start of PromJet */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe8000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_BR0_PRELIM \
+ (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
+ | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
+
+#define CONFIG_FSL_CPLD
+#define CPLD_BASE 0xffdf0000 /* CPLD registers */
+#ifdef CONFIG_PHYS_64BIT
+#define CPLD_BASE_PHYS 0xfffdf0000ull
+#else
+#define CPLD_BASE_PHYS CPLD_BASE
+#endif
+
+#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
+
+#define PIXIS_LBMAP_SWITCH 7
+#define PIXIS_LBMAP_MASK 0xf0
+#define PIXIS_LBMAP_SHIFT 4
+#define PIXIS_LBMAP_ALTBANK 0x40
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED 400000
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x118000
+#define CONFIG_SYS_I2C2_OFFSET 0x118100
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
+
+#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
+#else
+#define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000
+#endif
+#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* Qman/Bman */
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 10
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 10
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+/* Default address of microcode for the Linux Fman driver */
+#define CONFIG_SYS_FMAN_FW
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH 0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FW_IN_MMC (512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FW_IN_NAND (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_FMAN_FW_ADDR 0xEF000000
+#endif
+#define CONFIG_SYS_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_FMAN_FW_LENGTH)
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
+#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3
+#define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4
+#define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1
+#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0
+
+#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c
+#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d
+#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e
+#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f
+
+#define CONFIG_SYS_TBIPA_VALUE 8
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC1"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH /opt/nfsroot
+#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE 115200
+
+#define __USB_PHY_TYPE utmi
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
+ "bank_intlv=cs0_cs1\0" \
+ "netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" MK_STR(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "usb_phy_type=" MK_STR(__USB_PHY_TYPE) "\0" \
+ "usb_dr_mode=host\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=p2041rdb/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=p2041rdb/p2041rdb.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif /* __CONFIG_H */
void set_working_fdt_addr(void *addr);
int fdt_resize(void *blob);
+int fdt_increase_size(void *fdt, int add_len);
int fdt_fixup_nor_flash_size(void *blob);
int fdt_node_offset_by_compat_reg(void *blob, const char *compat,
phys_addr_t compat_off);
int fdt_alloc_phandle(void *blob);
+int fdt_create_phandle(void *fdt, int nodeoffset, uint32_t phandle);
int fdt_add_edid(void *blob, const char *compat, unsigned char *buf);
+int fdt_verify_alias_address(void *fdt, int anode, const char *alias,
+ u64 addr);
+u64 fdt_get_base_address(void *fdt, int node);
+
#endif /* ifdef CONFIG_OF_LIBFDT */
#endif /* ifndef __FDT_SUPPORT_H */
*/
const char *fdt_get_name(const void *fdt, int nodeoffset, int *lenp);
+/**
+ * fdt_first_property_offset - find the offset of a node's first property
+ * @fdt: pointer to the device tree blob
+ * @nodeoffset: structure block offset of a node
+ *
+ * fdt_first_property_offset() finds the first property of the node at
+ * the given structure block offset.
+ *
+ * returns:
+ * structure block offset of the property (>=0), on success
+ * -FDT_ERR_NOTFOUND, if the requested node has no properties
+ * -FDT_ERR_BADOFFSET, if nodeoffset did not point to an FDT_BEGIN_NODE tag
+ * -FDT_ERR_BADMAGIC,
+ * -FDT_ERR_BADVERSION,
+ * -FDT_ERR_BADSTATE,
+ * -FDT_ERR_BADSTRUCTURE,
+ * -FDT_ERR_TRUNCATED, standard meanings.
+ */
+int fdt_first_property_offset(const void *fdt, int nodeoffset);
+
+/**
+ * fdt_next_property_offset - step through a node's properties
+ * @fdt: pointer to the device tree blob
+ * @offset: structure block offset of a property
+ *
+ * fdt_next_property_offset() finds the property immediately after the
+ * one at the given structure block offset. This will be a property
+ * of the same node as the given property.
+ *
+ * returns:
+ * structure block offset of the next property (>=0), on success
+ * -FDT_ERR_NOTFOUND, if the given property is the last in its node
+ * -FDT_ERR_BADOFFSET, if nodeoffset did not point to an FDT_PROP tag
+ * -FDT_ERR_BADMAGIC,
+ * -FDT_ERR_BADVERSION,
+ * -FDT_ERR_BADSTATE,
+ * -FDT_ERR_BADSTRUCTURE,
+ * -FDT_ERR_TRUNCATED, standard meanings.
+ */
+int fdt_next_property_offset(const void *fdt, int offset);
+
+/**
+ * fdt_get_property_by_offset - retrieve the property at a given offset
+ * @fdt: pointer to the device tree blob
+ * @offset: offset of the property to retrieve
+ * @lenp: pointer to an integer variable (will be overwritten) or NULL
+ *
+ * fdt_get_property_by_offset() retrieves a pointer to the
+ * fdt_property structure within the device tree blob at the given
+ * offset. If lenp is non-NULL, the length of the property value is
+ * also returned, in the integer pointed to by lenp.
+ *
+ * returns:
+ * pointer to the structure representing the property
+ * if lenp is non-NULL, *lenp contains the length of the property
+ * value (>=0)
+ * NULL, on error
+ * if lenp is non-NULL, *lenp contains an error code (<0):
+ * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_PROP tag
+ * -FDT_ERR_BADMAGIC,
+ * -FDT_ERR_BADVERSION,
+ * -FDT_ERR_BADSTATE,
+ * -FDT_ERR_BADSTRUCTURE,
+ * -FDT_ERR_TRUNCATED, standard meanings
+ */
+const struct fdt_property *fdt_get_property_by_offset(const void *fdt,
+ int offset,
+ int *lenp);
+
/**
* fdt_get_property_namelen - find a property based on substring
* @fdt: pointer to the device tree blob
fdt_get_property(fdt, nodeoffset, name, lenp);
}
+/**
+ * fdt_getprop_by_offset - retrieve the value of a property at a given offset
+ * @fdt: pointer to the device tree blob
+ * @ffset: offset of the property to read
+ * @namep: pointer to a string variable (will be overwritten) or NULL
+ * @lenp: pointer to an integer variable (will be overwritten) or NULL
+ *
+ * fdt_getprop_by_offset() retrieves a pointer to the value of the
+ * property at structure block offset 'offset' (this will be a pointer
+ * to within the device blob itself, not a copy of the value). If
+ * lenp is non-NULL, the length of the property value is also
+ * returned, in the integer pointed to by lenp. If namep is non-NULL,
+ * the property's namne will also be returned in the char * pointed to
+ * by namep (this will be a pointer to within the device tree's string
+ * block, not a new copy of the name).
+ *
+ * returns:
+ * pointer to the property's value
+ * if lenp is non-NULL, *lenp contains the length of the property
+ * value (>=0)
+ * if namep is non-NULL *namep contiains a pointer to the property
+ * name.
+ * NULL, on error
+ * if lenp is non-NULL, *lenp contains an error code (<0):
+ * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_PROP tag
+ * -FDT_ERR_BADMAGIC,
+ * -FDT_ERR_BADVERSION,
+ * -FDT_ERR_BADSTATE,
+ * -FDT_ERR_BADSTRUCTURE,
+ * -FDT_ERR_TRUNCATED, standard meanings
+ */
+const void *fdt_getprop_by_offset(const void *fdt, int offset,
+ const char **namep, int *lenp);
+
/**
* fdt_getprop_namelen - get property value based on substring
* @fdt: pointer to the device tree blob
return offset;
}
+int _fdt_check_prop_offset(const void *fdt, int offset)
+{
+ if ((offset < 0) || (offset % FDT_TAGSIZE)
+ || (fdt_next_tag(fdt, offset, &offset) != FDT_PROP))
+ return -FDT_ERR_BADOFFSET;
+
+ return offset;
+}
+
int fdt_next_node(const void *fdt, int offset, int *depth)
{
int nextoffset = 0;
return i;
}
+static int _nextprop(const void *fdt, int offset)
+{
+ uint32_t tag;
+ int nextoffset;
+
+ do {
+ tag = fdt_next_tag(fdt, offset, &nextoffset);
+
+ switch (tag) {
+ case FDT_END:
+ if (nextoffset >= 0)
+ return -FDT_ERR_BADSTRUCTURE;
+ else
+ return nextoffset;
+
+ case FDT_PROP:
+ return offset;
+ }
+ offset = nextoffset;
+ } while (tag == FDT_NOP);
+
+ return -FDT_ERR_NOTFOUND;
+}
+
int fdt_subnode_offset_namelen(const void *fdt, int offset,
const char *name, int namelen)
{
return NULL;
}
-const struct fdt_property *fdt_get_property_namelen(const void *fdt,
- int nodeoffset,
- const char *name,
- int namelen, int *lenp)
+int fdt_first_property_offset(const void *fdt, int nodeoffset)
+{
+ int offset;
+
+ if ((offset = _fdt_check_node_offset(fdt, nodeoffset)) < 0)
+ return offset;
+
+ return _nextprop(fdt, offset);
+}
+
+int fdt_next_property_offset(const void *fdt, int offset)
+{
+ if ((offset = _fdt_check_prop_offset(fdt, offset)) < 0)
+ return offset;
+
+ return _nextprop(fdt, offset);
+}
+
+const struct fdt_property *fdt_get_property_by_offset(const void *fdt,
+ int offset,
+ int *lenp)
{
- uint32_t tag;
- const struct fdt_property *prop;
- int offset, nextoffset;
int err;
+ const struct fdt_property *prop;
- if (((err = fdt_check_header(fdt)) != 0)
- || ((err = _fdt_check_node_offset(fdt, nodeoffset)) < 0))
- goto fail;
+ if ((err = _fdt_check_prop_offset(fdt, offset)) < 0) {
+ if (lenp)
+ *lenp = err;
+ return NULL;
+ }
- nextoffset = err;
- do {
- offset = nextoffset;
+ prop = _fdt_offset_ptr(fdt, offset);
- tag = fdt_next_tag(fdt, offset, &nextoffset);
- switch (tag) {
- case FDT_END:
- if (nextoffset < 0)
- err = nextoffset;
- else
- /* FDT_END tag with unclosed nodes */
- err = -FDT_ERR_BADSTRUCTURE;
- goto fail;
+ if (lenp)
+ *lenp = fdt32_to_cpu(prop->len);
- case FDT_PROP:
- prop = _fdt_offset_ptr(fdt, offset);
- if (_fdt_string_eq(fdt, fdt32_to_cpu(prop->nameoff),
- name, namelen)) {
- /* Found it! */
- if (lenp)
- *lenp = fdt32_to_cpu(prop->len);
-
- return prop;
- }
+ return prop;
+}
+
+const struct fdt_property *fdt_get_property_namelen(const void *fdt,
+ int offset,
+ const char *name,
+ int namelen, int *lenp)
+{
+ for (offset = fdt_first_property_offset(fdt, offset);
+ (offset >= 0);
+ (offset = fdt_next_property_offset(fdt, offset))) {
+ const struct fdt_property *prop;
+
+ if (!(prop = fdt_get_property_by_offset(fdt, offset, lenp))) {
+ offset = -FDT_ERR_INTERNAL;
break;
}
- } while ((tag != FDT_BEGIN_NODE) && (tag != FDT_END_NODE));
+ if (_fdt_string_eq(fdt, fdt32_to_cpu(prop->nameoff),
+ name, namelen))
+ return prop;
+ }
- err = -FDT_ERR_NOTFOUND;
- fail:
if (lenp)
- *lenp = err;
+ *lenp = offset;
return NULL;
}
return prop->data;
}
+const void *fdt_getprop_by_offset(const void *fdt, int offset,
+ const char **namep, int *lenp)
+{
+ const struct fdt_property *prop;
+
+ prop = fdt_get_property_by_offset(fdt, offset, lenp);
+ if (!prop)
+ return NULL;
+ if (namep)
+ *namep = fdt_string(fdt, fdt32_to_cpu(prop->nameoff));
+ return prop->data;
+}
+
const void *fdt_getprop(const void *fdt, int nodeoffset,
const char *name, int *lenp)
{
const uint32_t *php;
int len;
- php = fdt_getprop(fdt, nodeoffset, "linux,phandle", &len);
- if (!php || (len != sizeof(*php)))
- return 0;
+ /* FIXME: This is a bit sub-optimal, since we potentially scan
+ * over all the properties twice. */
+ php = fdt_getprop(fdt, nodeoffset, "phandle", &len);
+ if (!php || (len != sizeof(*php))) {
+ php = fdt_getprop(fdt, nodeoffset, "linux,phandle", &len);
+ if (!php || (len != sizeof(*php)))
+ return 0;
+ }
return fdt32_to_cpu(*php);
}
int fdt_node_offset_by_phandle(const void *fdt, uint32_t phandle)
{
+ int offset;
+
if ((phandle == 0) || (phandle == -1))
return -FDT_ERR_BADPHANDLE;
- phandle = cpu_to_fdt32(phandle);
- return fdt_node_offset_by_prop_value(fdt, -1, "linux,phandle",
- &phandle, sizeof(phandle));
+
+ FDT_CHECK_HEADER(fdt);
+
+ /* FIXME: The algorithm here is pretty horrible: we
+ * potentially scan each property of a node in
+ * fdt_get_phandle(), then if that didn't find what
+ * we want, we scan over them again making our way to the next
+ * node. Still it's the easiest to implement approach;
+ * performance can come later. */
+ for (offset = fdt_next_node(fdt, -1, NULL);
+ offset >= 0;
+ offset = fdt_next_node(fdt, offset, NULL)) {
+ if (fdt_get_phandle(fdt, offset) == phandle)
+ return offset;
+ }
+
+ return offset; /* error from fdt_next_node() */
}
static int _fdt_stringlist_contains(const char *strlist, int listlen,
}
int _fdt_check_node_offset(const void *fdt, int offset);
+int _fdt_check_prop_offset(const void *fdt, int offset);
const char *_fdt_find_string(const char *strtab, int tabsize, const char *s);
int _fdt_node_end_offset(void *fdt, int nodeoffset);
projects / karo-tx-uboot.git / commitdiff