Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
MS7720SE SH7720
+ R0P77570030RL SH7757
R0P77850011RL SH7785
#########################################################################
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
+ CONFIG_SH_ETHER
+ Support for Renesas on-chip Ethernet controller
+
+ CONFIG_SH_ETHER_USE_PORT
+ Define the number of ports to be used
+
+ CONFIG_SH_ETHER_PHY_ADDR
+ Define the ETH PHY's address
+
+ CONFIG_SH_ETHER_CACHE_WRITEBACK
+ If this option is set, the driver enables cache flush.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
SPI EEPROM, also an instance works with Crystal A/D and
D/As on the SACSng board)
+ CONFIG_SH_SPI
+
+ Enables the driver for SPI controller on SuperH. Currently
+ only SH7757 is supported.
+
CONFIG_SPI_X
Enables extended (16-bit) SPI EEPROM addressing.
PLATFORM_CPPFLAGS += -DCONFIG_SH -D__SH__
PLATFORM_LDFLAGS += -e $(CONFIG_SYS_TEXT_BASE) --defsym reloc_dst=$(CONFIG_SYS_TEXT_BASE)
LDFLAGS_u-boot = --gc-sections
+
+ifdef CONFIG_SYS_LDSCRIPT
+LDSCRIPT := $(subst ",,$(CONFIG_SYS_LDSCRIPT))
+else
LDSCRIPT := $(SRCTREE)/$(CPUDIR)/u-boot.lds
+endif
+
# include <asm/cpu_sh7722.h>
#elif defined (CONFIG_CPU_SH7723)
# include <asm/cpu_sh7723.h>
+#elif defined (CONFIG_CPU_SH7757)
+# include <asm/cpu_sh7757.h>
#elif defined (CONFIG_CPU_SH7763)
# include <asm/cpu_sh7763.h>
#elif defined (CONFIG_CPU_SH7780)
--- /dev/null
+/*
+ * Copyright (C) 2011 Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef _ASM_CPU_SH7757_H_
+#define _ASM_CPU_SH7757_H_
+
+#define CCR 0xFF00001C
+#define WTCNT 0xFFCC0000
+#define CCR_CACHE_INIT 0x0000090b
+#define CACHE_OC_NUM_WAYS 1
+
+#ifndef __ASSEMBLY__ /* put C only stuff in this section */
+/* MMU */
+struct mmu_regs {
+ unsigned int reserved[4];
+ unsigned int mmucr;
+};
+#define MMU_BASE ((struct mmu_regs *)0xff000000)
+
+/* Watchdog */
+#define WTCSR0 0xffcc0002
+#define WRSTCSR_R 0xffcc0003
+#define WRSTCSR_W 0xffcc0002
+#define WTCSR_PREFIX 0xa500
+#define WRSTCSR_PREFIX 0x6900
+#define WRSTCSR_WOVF_PREFIX 0x9600
+
+/* SCIF */
+#define SCIF0_BASE 0xfe4b0000 /* The real name is SCIF2 */
+#define SCIF1_BASE 0xfe4c0000 /* The real name is SCIF3 */
+#define SCIF2_BASE 0xfe4d0000 /* The real name is SCIF4 */
+
+/* SerMux */
+#define SMR0 0xfe470000
+
+/* TMU0 */
+#define TSTR 0xFE430004
+#define TOCR 0xFE430000
+#define TSTR0 0xFE430004
+#define TCOR0 0xFE430008
+#define TCNT0 0xFE43000C
+#define TCR0 0xFE430010
+#define TCOR1 0xFE430014
+#define TCNT1 0xFE430018
+#define TCR1 0xFE43001C
+#define TCOR2 0xFE430020
+#define TCNT2 0xFE430024
+#define TCR2 0xFE430028
+#define TCPR2 0xFE43002C
+
+/* ETHER, GETHER MAC address */
+struct ether_mac_regs {
+ unsigned int reserved[114];
+ unsigned int mahr;
+ unsigned int reserved2;
+ unsigned int malr;
+};
+#define GETHER0_MAC_BASE ((struct ether_mac_regs *)0xfee0400)
+#define GETHER1_MAC_BASE ((struct ether_mac_regs *)0xfee0c00)
+#define ETHER0_MAC_BASE ((struct ether_mac_regs *)0xfef0000)
+#define ETHER1_MAC_BASE ((struct ether_mac_regs *)0xfef0800)
+
+/* GETHER */
+struct gether_control_regs {
+ unsigned int gbecont;
+};
+#define GETHER_CONTROL_BASE ((struct gether_control_regs *)0xffc10100)
+#define GBECONT_RMII1 0x00020000
+#define GBECONT_RMII0 0x00010000
+
+/* USB0/1 */
+struct usb_common_regs {
+ unsigned short reserved[129];
+ unsigned short suspmode;
+};
+#define USB0_COMMON_BASE ((struct usb_common_regs *)0xfe450000)
+#define USB1_COMMON_BASE ((struct usb_common_regs *)0xfe4f0000)
+
+struct usb0_phy_regs {
+ unsigned short reset;
+ unsigned short reserved[4];
+ unsigned short portsel;
+};
+#define USB0_PHY_BASE ((struct usb0_phy_regs *)0xfe5f0000)
+
+struct usb1_port_regs {
+ unsigned int port1sel;
+ unsigned int reserved;
+ unsigned int usb1intsts;
+};
+#define USB1_PORT_BASE ((struct usb1_port_regs *)0xfe4f2000)
+
+struct usb1_alignment_regs {
+ unsigned int ehcidatac; /* 0xfe4fe018 */
+ unsigned int reserved[63];
+ unsigned int ohcidatac;
+};
+#define USB1_ALIGNMENT_BASE ((struct usb1_alignment_regs *)0xfe4fe018)
+
+/* GCTRL, GRA */
+struct gctrl_regs {
+ unsigned int wprotect;
+ unsigned int gplldiv;
+ unsigned int gracr2; /* GRA */
+ unsigned int gracr3; /* GRA */
+ unsigned int reserved[4];
+ unsigned int fcntcr1;
+ unsigned int fcntcr2;
+ unsigned int reserved2[2];
+ unsigned int gpll1div;
+ unsigned int vcompsel;
+ unsigned int reserved3[62];
+ unsigned int fdlmon;
+ unsigned int reserved4[2];
+ unsigned int flcrmon;
+ unsigned int reserved5[944];
+ unsigned int spibootcan;
+};
+#define GCTRL_BASE ((struct gctrl_regs *)0xffc10000)
+
+/* PCIe setup */
+struct pcie_setup_regs {
+ unsigned int pbictl0;
+ unsigned int gradevctl;
+ unsigned int reserved[2];
+ unsigned int bmcinf[6];
+ unsigned int reserved2[118];
+ unsigned int idset[2];
+ unsigned int subidset;
+ unsigned int reserved3[2];
+ unsigned int linkconfset[4];
+ unsigned int trsid;
+ unsigned int reserved4[6];
+ unsigned int toutset;
+ unsigned int reserved5[7];
+ unsigned int lad0;
+ unsigned int ladmsk0;
+ unsigned int lad1;
+ unsigned int ladmsk1;
+ unsigned int lad2;
+ unsigned int ladmsk2;
+ unsigned int lad3;
+ unsigned int ladmsk3;
+ unsigned int lad4;
+ unsigned int ladmsk4;
+ unsigned int lad5;
+ unsigned int ladmsk5;
+ unsigned int reserved6[94];
+ unsigned int vdmrxvid[2];
+ unsigned int reserved7;
+ unsigned int pbiintfr;
+ unsigned int pbiinten;
+ unsigned int msimap;
+ unsigned int barmap;
+ unsigned int baracsize;
+ unsigned int advserest;
+ unsigned int pbictl3;
+ unsigned int reserved8[8];
+ unsigned int pbictl1;
+ unsigned int scratch0;
+ unsigned int reserved9[6];
+ unsigned int pbictl2;
+ unsigned int reserved10;
+ unsigned int pbirev;
+};
+#define PCIE_SETUP_BASE ((struct pcie_setup_regs *)0xffca1000)
+
+struct pcie_system_bus_regs {
+ unsigned int reserved[3];
+ unsigned int endictl0;
+ unsigned int endictl1;
+};
+#define PCIE_SYSTEM_BUS_BASE ((struct pcie_system_bus_regs *)0xffca1600)
+
+
+/* PCIe-Bridge */
+struct pciebrg_regs {
+ unsigned short ctrl_h8s;
+ unsigned short reserved[7];
+ unsigned short cp_addr;
+ unsigned short reserved2;
+ unsigned short cp_data;
+ unsigned short reserved3;
+ unsigned short cp_ctrl;
+};
+#define PCIEBRG_BASE ((struct pciebrg_regs *)0xffd60000)
+
+/* CPU version */
+#define CCN_PRR 0xff000044
+#define prr_mask(_val) ((_val >> 4) & 0xff)
+#define PRR_SH7757_B0 0x10
+#define PRR_SH7757_C0 0x11
+
+#define is_sh7757_b0(_val) \
+({ \
+ int __ret = prr_mask(__raw_readl(CCN_PRR)) == PRR_SH7757_B0; \
+ __ret; \
+})
+#endif /* ifndef __ASSEMBLY__ */
+
+#endif /* _ASM_CPU_SH7757_H_ */
+++ /dev/null
-#
-# board/espt/config.mk
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007
-# Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
-#
-# Copyright (C) 2007
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# Copyright (C) 2007
-# Kenati Technologies, Inc.
-#
-# Copyright (C) 2008
-# Mark Jonas <mark.jonas@de.bosch.com>
-#
-# board/mpr2/config.mk
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007
-# Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
-#
-# Copyright (C) 2007
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# Copyright (C) 2007
-# Kenati Technologies, Inc.
-#
-# board/ms7720se/config.mk
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# Copyright (C) 2007
-# Kenati Technologies, Inc.
-#
-# board/ms7722se/config.mk
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007,2008
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-CONFIG_SYS_TEXT_BASE = 0x0FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007,2008 Nobuhiro Iwamatsu
-#
-# board/r77870mp/config.mk
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x0FFC0000
+++ /dev/null
-#
-# Copyright (C) 2007,2008 Nobuhiro Iwamatsu
-# Copyright (C) 2008 Renesas Solutions Corp.
-#
-# u-boot/board/rsk7203/config.mk
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x0C7C0000
#
-# Copyright (C) 2007
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# Copyright (C) 2007
-# Kenati Technologies, Inc.
-#
-# board/MigoR/config.mk
+# Copyright (C) 2011 Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := sh7757lcr.o spi-boot.o
+SOBJS := lowlevel_init.o
+
+$(LIB): $(obj).depend $(COBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(COBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
--- /dev/null
+/*
+ * Copyright (C) 2011 Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/processor.h>
+#include <asm/macro.h>
+
+.macro or32, addr, data
+ mov.l \addr, r1
+ mov.l \data, r0
+ mov.l @r1, r2
+ or r2, r0
+ mov.l r0, @r1
+.endm
+
+.macro wait_DBCMD
+ mov.l DBWAIT_A, r0
+ mov.l @r0, r1
+.endm
+
+ .global lowlevel_init
+ .section .spiboot1.text
+ .align 2
+
+lowlevel_init:
+
+ /*------- GPIO -------*/
+ write8 PGDR_A, PGDR_D /* eMMC power off */
+
+ write16 PACR_A, PACR_D
+ write16 PBCR_A, PBCR_D
+ write16 PCCR_A, PCCR_D
+ write16 PDCR_A, PDCR_D
+ write16 PECR_A, PECR_D
+ write16 PFCR_A, PFCR_D
+ write16 PGCR_A, PGCR_D
+ write16 PHCR_A, PHCR_D
+ write16 PICR_A, PICR_D
+ write16 PJCR_A, PJCR_D
+ write16 PKCR_A, PKCR_D
+ write16 PLCR_A, PLCR_D
+ write16 PMCR_A, PMCR_D
+ write16 PNCR_A, PNCR_D
+ write16 POCR_A, POCR_D
+ write16 PQCR_A, PQCR_D
+ write16 PRCR_A, PRCR_D
+ write16 PSCR_A, PSCR_D
+ write16 PTCR_A, PTCR_D
+ write16 PUCR_A, PUCR_D
+ write16 PVCR_A, PVCR_D
+ write16 PWCR_A, PWCR_D
+ write16 PXCR_A, PXCR_D
+ write16 PYCR_A, PYCR_D
+ write16 PZCR_A, PZCR_D
+ write16 PSEL0_A, PSEL0_D
+ write16 PSEL1_A, PSEL1_D
+ write16 PSEL2_A, PSEL2_D
+ write16 PSEL3_A, PSEL3_D
+ write16 PSEL4_A, PSEL4_D
+ write16 PSEL5_A, PSEL5_D
+ write16 PSEL6_A, PSEL6_D
+ write16 PSEL7_A, PSEL7_D
+ write16 PSEL8_A, PSEL8_D
+
+ bra exit_gpio
+ nop
+
+ .align 4
+
+/*------- GPIO -------*/
+PGDR_A: .long 0xffec0040
+PACR_A: .long 0xffec0000
+PBCR_A: .long 0xffec0002
+PCCR_A: .long 0xffec0004
+PDCR_A: .long 0xffec0006
+PECR_A: .long 0xffec0008
+PFCR_A: .long 0xffec000a
+PGCR_A: .long 0xffec000c
+PHCR_A: .long 0xffec000e
+PICR_A: .long 0xffec0010
+PJCR_A: .long 0xffec0012
+PKCR_A: .long 0xffec0014
+PLCR_A: .long 0xffec0016
+PMCR_A: .long 0xffec0018
+PNCR_A: .long 0xffec001a
+POCR_A: .long 0xffec001c
+PQCR_A: .long 0xffec0020
+PRCR_A: .long 0xffec0022
+PSCR_A: .long 0xffec0024
+PTCR_A: .long 0xffec0026
+PUCR_A: .long 0xffec0028
+PVCR_A: .long 0xffec002a
+PWCR_A: .long 0xffec002c
+PXCR_A: .long 0xffec002e
+PYCR_A: .long 0xffec0030
+PZCR_A: .long 0xffec0032
+PSEL0_A: .long 0xffec0070
+PSEL1_A: .long 0xffec0072
+PSEL2_A: .long 0xffec0074
+PSEL3_A: .long 0xffec0076
+PSEL4_A: .long 0xffec0078
+PSEL5_A: .long 0xffec007a
+PSEL6_A: .long 0xffec007c
+PSEL7_A: .long 0xffec0082
+PSEL8_A: .long 0xffec0084
+
+PGDR_D: .long 0x80
+PACR_D: .long 0x0000
+PBCR_D: .long 0x0001
+PCCR_D: .long 0x0000
+PDCR_D: .long 0x0000
+PECR_D: .long 0x0000
+PFCR_D: .long 0x0000
+PGCR_D: .long 0x0000
+PHCR_D: .long 0x0000
+PICR_D: .long 0x0000
+PJCR_D: .long 0x0000
+PKCR_D: .long 0x0003
+PLCR_D: .long 0x0000
+PMCR_D: .long 0x0000
+PNCR_D: .long 0x0000
+POCR_D: .long 0x0000
+PQCR_D: .long 0xc000
+PRCR_D: .long 0x0000
+PSCR_D: .long 0x0000
+PTCR_D: .long 0x0000
+#if defined(CONFIG_SH7757_OFFSET_SPI)
+PUCR_D: .long 0x0055
+#else
+PUCR_D: .long 0x0000
+#endif
+PVCR_D: .long 0x0000
+PWCR_D: .long 0x0000
+PXCR_D: .long 0x0000
+PYCR_D: .long 0x0000
+PZCR_D: .long 0x0000
+PSEL0_D: .long 0xfe00
+PSEL1_D: .long 0x0000
+PSEL2_D: .long 0x3000
+PSEL3_D: .long 0xff00
+PSEL4_D: .long 0x771f
+PSEL5_D: .long 0x0ffc
+PSEL6_D: .long 0x00ff
+PSEL7_D: .long 0xfc00
+PSEL8_D: .long 0x0000
+
+ .align 2
+
+exit_gpio:
+ mov #0, r14
+ mova 2f, r0
+ mov.l PC_MASK, r1
+ tst r0, r1
+ bf 2f
+
+ bra exit_pmb
+ nop
+
+ .align 2
+
+/* If CPU runs on SDRAM, PC is 0x8???????. */
+PC_MASK: .long 0x20000000
+
+2:
+ mov #1, r14
+
+ mov.l EXPEVT_A, r0
+ mov.l @r0, r0
+ mov.l EXPEVT_POWER_ON_RESET, r1
+ cmp/eq r0, r1
+ bt 1f
+
+ /*
+ * If EXPEVT value is manual reset or tlb multipul-hit,
+ * initialization of DDR3IF is not necessary.
+ */
+ bra exit_ddr
+ nop
+
+1:
+ /* For Core Reset */
+ mov.l DBACEN_A, r0
+ mov.l @r0, r0
+ cmp/eq #0, r0
+ bt 3f
+
+ /*
+ * If DBACEN == 1(DBSC was already enabled), we have to avoid the
+ * initialization of DDR3-SDRAM.
+ */
+ bra exit_ddr
+ nop
+
+3:
+ /*------- DDR3IF -------*/
+ /* oscillation stabilization time */
+ wait_timer WAIT_OSC_TIME
+
+ /* step 3 */
+ write32 DBCMD_A, DBCMD_RSTL_VAL
+ wait_timer WAIT_30US
+
+ /* step 4 */
+ write32 DBCMD_A, DBCMD_PDEN_VAL
+
+ /* step 5 */
+ write32 DBKIND_A, DBKIND_D
+
+ /* step 6 */
+ write32 DBCONF_A, DBCONF_D
+ write32 DBTR0_A, DBTR0_D
+ write32 DBTR1_A, DBTR1_D
+ write32 DBTR2_A, DBTR2_D
+ write32 DBTR3_A, DBTR3_D
+ write32 DBTR4_A, DBTR4_D
+ write32 DBTR5_A, DBTR5_D
+ write32 DBTR6_A, DBTR6_D
+ write32 DBTR7_A, DBTR7_D
+ write32 DBTR8_A, DBTR8_D
+ write32 DBTR9_A, DBTR9_D
+ write32 DBTR10_A, DBTR10_D
+ write32 DBTR11_A, DBTR11_D
+ write32 DBTR12_A, DBTR12_D
+ write32 DBTR13_A, DBTR13_D
+ write32 DBTR14_A, DBTR14_D
+ write32 DBTR15_A, DBTR15_D
+ write32 DBTR16_A, DBTR16_D
+ write32 DBTR17_A, DBTR17_D
+ write32 DBTR18_A, DBTR18_D
+ write32 DBTR19_A, DBTR19_D
+ write32 DBRNK0_A, DBRNK0_D
+
+ /* step 7 */
+ write32 DBPDCNT3_A, DBPDCNT3_D
+
+ /* step 8 */
+ write32 DBPDCNT1_A, DBPDCNT1_D
+ write32 DBPDCNT2_A, DBPDCNT2_D
+ write32 DBPDLCK_A, DBPDLCK_D
+ write32 DBPDRGA_A, DBPDRGA_D
+ write32 DBPDRGD_A, DBPDRGD_D
+
+ /* step 9 */
+ wait_timer WAIT_30US
+
+ /* step 10 */
+ write32 DBPDCNT0_A, DBPDCNT0_D
+
+ /* step 11 */
+ wait_timer WAIT_30US
+ wait_timer WAIT_30US
+
+ /* step 12 */
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ wait_DBCMD
+
+ /* step 13 */
+ write32 DBCMD_A, DBCMD_RSTH_VAL
+ wait_DBCMD
+
+ /* step 14 */
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+
+ /* step 15 */
+ write32 DBCMD_A, DBCMD_PDXT_VAL
+
+ /* step 16 */
+ write32 DBCMD_A, DBCMD_MRS2_VAL
+
+ /* step 17 */
+ write32 DBCMD_A, DBCMD_MRS3_VAL
+
+ /* step 18 */
+ write32 DBCMD_A, DBCMD_MRS1_VAL
+
+ /* step 19 */
+ write32 DBCMD_A, DBCMD_MRS0_VAL
+
+ /* step 20 */
+ write32 DBCMD_A, DBCMD_ZQCL_VAL
+
+ write32 DBCMD_A, DBCMD_REF_VAL
+ write32 DBCMD_A, DBCMD_REF_VAL
+ wait_DBCMD
+
+ /* step 21 */
+ write32 DBADJ0_A, DBADJ0_D
+ write32 DBADJ1_A, DBADJ1_D
+ write32 DBADJ2_A, DBADJ2_D
+
+ /* step 22 */
+ write32 DBRFCNF0_A, DBRFCNF0_D
+ write32 DBRFCNF1_A, DBRFCNF1_D
+ write32 DBRFCNF2_A, DBRFCNF2_D
+
+ /* step 23 */
+ write32 DBCALCNF_A, DBCALCNF_D
+
+ /* step 24 */
+ write32 DBRFEN_A, DBRFEN_D
+ write32 DBCMD_A, DBCMD_SRXT_VAL
+
+ /* step 25 */
+ write32 DBACEN_A, DBACEN_D
+
+ /* step 26 */
+ wait_DBCMD
+
+ /* enable DDR-ECC */
+ write32 ECD_ECDEN_A, ECD_ECDEN_D
+ write32 ECD_INTSR_A, ECD_INTSR_D
+ write32 ECD_SPACER_A, ECD_SPACER_D
+ write32 ECD_MCR_A, ECD_MCR_D
+
+ bra exit_ddr
+ nop
+
+ .align 4
+
+EXPEVT_A: .long 0xff000024
+EXPEVT_POWER_ON_RESET: .long 0x00000000
+
+/*------- DDR3IF -------*/
+DBCMD_A: .long 0xfe800018
+DBKIND_A: .long 0xfe800020
+DBCONF_A: .long 0xfe800024
+DBTR0_A: .long 0xfe800040
+DBTR1_A: .long 0xfe800044
+DBTR2_A: .long 0xfe800048
+DBTR3_A: .long 0xfe800050
+DBTR4_A: .long 0xfe800054
+DBTR5_A: .long 0xfe800058
+DBTR6_A: .long 0xfe80005c
+DBTR7_A: .long 0xfe800060
+DBTR8_A: .long 0xfe800064
+DBTR9_A: .long 0xfe800068
+DBTR10_A: .long 0xfe80006c
+DBTR11_A: .long 0xfe800070
+DBTR12_A: .long 0xfe800074
+DBTR13_A: .long 0xfe800078
+DBTR14_A: .long 0xfe80007c
+DBTR15_A: .long 0xfe800080
+DBTR16_A: .long 0xfe800084
+DBTR17_A: .long 0xfe800088
+DBTR18_A: .long 0xfe80008c
+DBTR19_A: .long 0xfe800090
+DBRNK0_A: .long 0xfe800100
+DBPDCNT0_A: .long 0xfe800200
+DBPDCNT1_A: .long 0xfe800204
+DBPDCNT2_A: .long 0xfe800208
+DBPDCNT3_A: .long 0xfe80020c
+DBPDLCK_A: .long 0xfe800280
+DBPDRGA_A: .long 0xfe800290
+DBPDRGD_A: .long 0xfe8002a0
+DBADJ0_A: .long 0xfe8000c0
+DBADJ1_A: .long 0xfe8000c4
+DBADJ2_A: .long 0xfe8000c8
+DBRFCNF0_A: .long 0xfe8000e0
+DBRFCNF1_A: .long 0xfe8000e4
+DBRFCNF2_A: .long 0xfe8000e8
+DBCALCNF_A: .long 0xfe8000f4
+DBRFEN_A: .long 0xfe800014
+DBACEN_A: .long 0xfe800010
+DBWAIT_A: .long 0xfe80001c
+
+WAIT_OSC_TIME: .long 6000
+WAIT_30US: .long 13333
+
+DBCMD_RSTL_VAL: .long 0x20000000
+DBCMD_PDEN_VAL: .long 0x1000d73c
+DBCMD_WAIT_VAL: .long 0x0000d73c
+DBCMD_RSTH_VAL: .long 0x2100d73c
+DBCMD_PDXT_VAL: .long 0x110000c8
+DBCMD_MRS0_VAL: .long 0x28000930
+DBCMD_MRS1_VAL: .long 0x29000004
+DBCMD_MRS2_VAL: .long 0x2a000008
+DBCMD_MRS3_VAL: .long 0x2b000000
+DBCMD_ZQCL_VAL: .long 0x03000200
+DBCMD_REF_VAL: .long 0x0c000000
+DBCMD_SRXT_VAL: .long 0x19000000
+DBKIND_D: .long 0x00000007
+DBCONF_D: .long 0x0f030a01
+DBTR0_D: .long 0x00000007
+DBTR1_D: .long 0x00000006
+DBTR2_D: .long 0x00000000
+DBTR3_D: .long 0x00000007
+DBTR4_D: .long 0x00070007
+DBTR5_D: .long 0x0000001b
+DBTR6_D: .long 0x00000014
+DBTR7_D: .long 0x00000005
+DBTR8_D: .long 0x00000015
+DBTR9_D: .long 0x00000006
+DBTR10_D: .long 0x00000008
+DBTR11_D: .long 0x00000007
+DBTR12_D: .long 0x0000000e
+DBTR13_D: .long 0x00000056
+DBTR14_D: .long 0x00000006
+DBTR15_D: .long 0x00000004
+DBTR16_D: .long 0x00150002
+DBTR17_D: .long 0x000c0017
+DBTR18_D: .long 0x00000200
+DBTR19_D: .long 0x00000040
+DBRNK0_D: .long 0x00000001
+DBPDCNT0_D: .long 0x00000001
+DBPDCNT1_D: .long 0x00000001
+DBPDCNT2_D: .long 0x00000000
+DBPDCNT3_D: .long 0x00004010
+DBPDLCK_D: .long 0x0000a55a
+DBPDRGA_D: .long 0x00000028
+DBPDRGD_D: .long 0x00017100
+
+DBADJ0_D: .long 0x00000000
+DBADJ1_D: .long 0x00000000
+DBADJ2_D: .long 0x18061806
+DBRFCNF0_D: .long 0x000001ff
+DBRFCNF1_D: .long 0x08001000
+DBRFCNF2_D: .long 0x00000000
+DBCALCNF_D: .long 0x0000ffff
+DBRFEN_D: .long 0x00000001
+DBACEN_D: .long 0x00000001
+
+/*------- DDR-ECC -------*/
+ECD_ECDEN_A: .long 0xffc1012c
+ECD_ECDEN_D: .long 0x00000001
+ECD_INTSR_A: .long 0xfe900024
+ECD_INTSR_D: .long 0xffffffff
+ECD_SPACER_A: .long 0xfe900018
+ECD_SPACER_D: .long SH7757LCR_SDRAM_ECC_SETTING
+ECD_MCR_A: .long 0xfe900010
+ECD_MCR_D: .long 0x00000001
+
+ .align 2
+exit_ddr:
+
+#if defined(CONFIG_SH_32BIT)
+ /*------- set PMB -------*/
+ write32 PASCR_A, PASCR_29BIT_D
+ write32 MMUCR_A, MMUCR_D
+
+ /*****************************************************************
+ * ent virt phys v sz c wt
+ * 0 0xa0000000 0x00000000 1 128M 0 1
+ * 1 0xa8000000 0x48000000 1 128M 0 1
+ * 5 0x88000000 0x48000000 1 128M 1 1
+ */
+ write32 PMB_ADDR_SPIBOOT_A, PMB_ADDR_SPIBOOT_D
+ write32 PMB_DATA_SPIBOOT_A, PMB_DATA_SPIBOOT_D
+ write32 PMB_ADDR_DDR_C1_A, PMB_ADDR_DDR_C1_D
+ write32 PMB_DATA_DDR_C1_A, PMB_DATA_DDR_C1_D
+ write32 PMB_ADDR_DDR_N1_A, PMB_ADDR_DDR_N1_D
+ write32 PMB_DATA_DDR_N1_A, PMB_DATA_DDR_N1_D
+
+ write32 PMB_ADDR_ENTRY2, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY3, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY4, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY6, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY7, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY8, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY9, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY10, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY11, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY12, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY13, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY14, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY15, PMB_ADDR_NOT_USE_D
+
+ write32 PASCR_A, PASCR_INIT
+ mov.l DUMMY_ADDR, r0
+ icbi @r0
+#endif /* if defined(CONFIG_SH_32BIT) */
+
+exit_pmb:
+ /* CPU is running on ILRAM? */
+ mov r14, r0
+ tst #1, r0
+ bt 1f
+
+ mov.l _bss_start, r15
+ mov.l _spiboot_main, r0
+100: bsrf r0
+ nop
+
+ .align 2
+_spiboot_main: .long (spiboot_main - (100b + 4))
+_bss_start: .long bss_start
+
+1:
+
+ write32 CCR_A, CCR_D
+
+ rts
+ nop
+
+ .align 4
+
+#if defined(CONFIG_SH_32BIT)
+/*------- set PMB -------*/
+PMB_ADDR_SPIBOOT_A: .long PMB_ADDR_BASE(0)
+PMB_ADDR_DDR_N1_A: .long PMB_ADDR_BASE(1)
+PMB_ADDR_DDR_C1_A: .long PMB_ADDR_BASE(5)
+PMB_ADDR_ENTRY2: .long PMB_ADDR_BASE(2)
+PMB_ADDR_ENTRY3: .long PMB_ADDR_BASE(3)
+PMB_ADDR_ENTRY4: .long PMB_ADDR_BASE(4)
+PMB_ADDR_ENTRY6: .long PMB_ADDR_BASE(6)
+PMB_ADDR_ENTRY7: .long PMB_ADDR_BASE(7)
+PMB_ADDR_ENTRY8: .long PMB_ADDR_BASE(8)
+PMB_ADDR_ENTRY9: .long PMB_ADDR_BASE(9)
+PMB_ADDR_ENTRY10: .long PMB_ADDR_BASE(10)
+PMB_ADDR_ENTRY11: .long PMB_ADDR_BASE(11)
+PMB_ADDR_ENTRY12: .long PMB_ADDR_BASE(12)
+PMB_ADDR_ENTRY13: .long PMB_ADDR_BASE(13)
+PMB_ADDR_ENTRY14: .long PMB_ADDR_BASE(14)
+PMB_ADDR_ENTRY15: .long PMB_ADDR_BASE(15)
+
+PMB_ADDR_SPIBOOT_D: .long mk_pmb_addr_val(0xa0)
+PMB_ADDR_DDR_C1_D: .long mk_pmb_addr_val(0x88)
+PMB_ADDR_DDR_N1_D: .long mk_pmb_addr_val(0xa8)
+PMB_ADDR_NOT_USE_D: .long 0x00000000
+
+PMB_DATA_SPIBOOT_A: .long PMB_DATA_BASE(0)
+PMB_DATA_DDR_N1_A: .long PMB_DATA_BASE(1)
+PMB_DATA_DDR_C1_A: .long PMB_DATA_BASE(5)
+
+/* ppn ub v s1 s0 c wt */
+PMB_DATA_SPIBOOT_D: .long mk_pmb_data_val(0x00, 0, 1, 1, 0, 0, 1)
+PMB_DATA_DDR_C1_D: .long mk_pmb_data_val(0x48, 0, 1, 1, 0, 1, 1)
+PMB_DATA_DDR_N1_D: .long mk_pmb_data_val(0x48, 1, 1, 1, 0, 0, 1)
+
+PASCR_A: .long 0xff000070
+DUMMY_ADDR: .long 0xa0000000
+PASCR_29BIT_D: .long 0x00000000
+PASCR_INIT: .long 0x80000080
+MMUCR_A: .long 0xff000010
+MMUCR_D: .long 0x00000004 /* clear ITLB */
+#endif /* CONFIG_SH_32BIT */
+
+CCR_A: .long CCR
+CCR_D: .long CCR_CACHE_INIT
--- /dev/null
+/*
+ * Copyright (C) 2011 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <spi_flash.h>
+
+int checkboard(void)
+{
+ puts("BOARD: R0P7757LC0030RL board\n");
+
+ return 0;
+}
+
+static void init_gctrl(void)
+{
+ struct gctrl_regs *gctrl = GCTRL_BASE;
+ unsigned long graofst;
+
+ graofst = (SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET) >> 24;
+ writel(graofst | 0x20000f00, &gctrl->gracr3);
+}
+
+static int init_pcie_bridge_from_spi(void *buf, size_t size)
+{
+ struct spi_flash *spi;
+ int ret;
+ unsigned long pcie_addr;
+
+ spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
+ if (!spi) {
+ printf("%s: spi_flash probe error.\n", __func__);
+ return 1;
+ }
+
+ if (is_sh7757_b0())
+ pcie_addr = SH7757LCR_PCIEBRG_ADDR_B0;
+ else
+ pcie_addr = SH7757LCR_PCIEBRG_ADDR;
+
+ ret = spi_flash_read(spi, pcie_addr, size, buf);
+ if (ret) {
+ printf("%s: spi_flash read error.\n", __func__);
+ spi_flash_free(spi);
+ return 1;
+ }
+ spi_flash_free(spi);
+
+ return 0;
+}
+
+static void init_pcie_bridge(void)
+{
+ struct pciebrg_regs *pciebrg = PCIEBRG_BASE;
+ struct pcie_setup_regs *pcie_setup = PCIE_SETUP_BASE;
+ int i;
+ unsigned char *data;
+ unsigned short tmp;
+ unsigned long pcie_size;
+
+ if (!(readw(&pciebrg->ctrl_h8s) & 0x0001))
+ return;
+
+ if (is_sh7757_b0())
+ pcie_size = SH7757LCR_PCIEBRG_SIZE_B0;
+ else
+ pcie_size = SH7757LCR_PCIEBRG_SIZE;
+
+ data = malloc(pcie_size);
+ if (!data) {
+ printf("%s: malloc error.\n", __func__);
+ return;
+ }
+ if (init_pcie_bridge_from_spi(data, pcie_size)) {
+ free(data);
+ return;
+ }
+
+ if (data[0] == 0xff && data[1] == 0xff && data[2] == 0xff &&
+ data[3] == 0xff) {
+ free(data);
+ printf("%s: skipped initialization\n", __func__);
+ return;
+ }
+
+ writew(0xa501, &pciebrg->ctrl_h8s); /* reset */
+ writew(0x0000, &pciebrg->cp_ctrl);
+ writew(0x0000, &pciebrg->cp_addr);
+
+ for (i = 0; i < pcie_size; i += 2) {
+ tmp = (data[i] << 8) | data[i + 1];
+ writew(tmp, &pciebrg->cp_data);
+ }
+
+ writew(0xa500, &pciebrg->ctrl_h8s); /* start */
+ if (!is_sh7757_b0())
+ writel(0x00000001, &pcie_setup->pbictl3);
+
+ free(data);
+}
+
+static void init_usb_phy(void)
+{
+ struct usb_common_regs *common0 = USB0_COMMON_BASE;
+ struct usb_common_regs *common1 = USB1_COMMON_BASE;
+ struct usb0_phy_regs *phy = USB0_PHY_BASE;
+ struct usb1_port_regs *port = USB1_PORT_BASE;
+ struct usb1_alignment_regs *align = USB1_ALIGNMENT_BASE;
+
+ writew(0x0100, &phy->reset); /* set reset */
+ /* port0 = USB0, port1 = USB1 */
+ writew(0x0002, &phy->portsel);
+ writel(0x0001, &port->port1sel); /* port1 = Host */
+ writew(0x0111, &phy->reset); /* clear reset */
+
+ writew(0x4000, &common0->suspmode);
+ writew(0x4000, &common1->suspmode);
+
+#if defined(__LITTLE_ENDIAN)
+ writel(0x00000000, &align->ehcidatac);
+ writel(0x00000000, &align->ohcidatac);
+#endif
+}
+
+static void set_mac_to_sh_eth_register(int channel, char *mac_string)
+{
+ struct ether_mac_regs *ether;
+ unsigned char mac[6];
+ unsigned long val;
+
+ eth_parse_enetaddr(mac_string, mac);
+
+ if (!channel)
+ ether = ETHER0_MAC_BASE;
+ else
+ ether = ETHER1_MAC_BASE;
+
+ val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3];
+ writel(val, ðer->mahr);
+ val = (mac[4] << 8) | mac[5];
+ writel(val, ðer->malr);
+}
+
+static void set_mac_to_sh_giga_eth_register(int channel, char *mac_string)
+{
+ struct ether_mac_regs *ether;
+ unsigned char mac[6];
+ unsigned long val;
+
+ eth_parse_enetaddr(mac_string, mac);
+
+ if (!channel)
+ ether = GETHER0_MAC_BASE;
+ else
+ ether = GETHER1_MAC_BASE;
+
+ val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3];
+ writel(val, ðer->mahr);
+ val = (mac[4] << 8) | mac[5];
+ writel(val, ðer->malr);
+}
+
+/*****************************************************************
+ * This PMB must be set on this timing. The lowlevel_init is run on
+ * Area 0(phys 0x00000000), so we have to map it.
+ *
+ * The new PMB table is following:
+ * ent virt phys v sz c wt
+ * 0 0xa0000000 0x40000000 1 128M 0 1
+ * 1 0xa8000000 0x48000000 1 128M 0 1
+ * 2 0xb0000000 0x50000000 1 128M 0 1
+ * 3 0xb8000000 0x58000000 1 128M 0 1
+ * 4 0x80000000 0x40000000 1 128M 1 1
+ * 5 0x88000000 0x48000000 1 128M 1 1
+ * 6 0x90000000 0x50000000 1 128M 1 1
+ * 7 0x98000000 0x58000000 1 128M 1 1
+ */
+static void set_pmb_on_board_init(void)
+{
+ struct mmu_regs *mmu = MMU_BASE;
+
+ /* clear ITLB */
+ writel(0x00000004, &mmu->mmucr);
+
+ /* delete PMB for SPIBOOT */
+ writel(0, PMB_ADDR_BASE(0));
+ writel(0, PMB_DATA_BASE(0));
+
+ /* add PMB for SDRAM(0x40000000 - 0x47ffffff) */
+ /* ppn ub v s1 s0 c wt */
+ writel(mk_pmb_addr_val(0xa0), PMB_ADDR_BASE(0));
+ writel(mk_pmb_data_val(0x40, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(0));
+ writel(mk_pmb_addr_val(0xb0), PMB_ADDR_BASE(2));
+ writel(mk_pmb_data_val(0x50, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(2));
+ writel(mk_pmb_addr_val(0xb8), PMB_ADDR_BASE(3));
+ writel(mk_pmb_data_val(0x58, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(3));
+ writel(mk_pmb_addr_val(0x80), PMB_ADDR_BASE(4));
+ writel(mk_pmb_data_val(0x40, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(4));
+ writel(mk_pmb_addr_val(0x90), PMB_ADDR_BASE(6));
+ writel(mk_pmb_data_val(0x50, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(6));
+ writel(mk_pmb_addr_val(0x98), PMB_ADDR_BASE(7));
+ writel(mk_pmb_data_val(0x58, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(7));
+}
+
+int board_init(void)
+{
+ struct gether_control_regs *gether = GETHER_CONTROL_BASE;
+
+ set_pmb_on_board_init();
+
+ /* enable RMII's MDIO (disable GRMII's MDIO) */
+ writel(0x00030000, &gether->gbecont);
+
+ init_gctrl();
+ init_usb_phy();
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
+ printf("DRAM: %dMB\n", CONFIG_SYS_SDRAM_SIZE / (1024 * 1024));
+ printf(" Physical address\n");
+ printf(" 0x%08x - 0x%08x : Accessible Space as ECC Area\n",
+ SH7757LCR_SDRAM_PHYS_TOP,
+ SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_SIZE - 1);
+ printf(" 0x%08x - 0x%08x : No Access Area\n",
+ SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_SIZE,
+ SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_SIZE * 2 - 1);
+ printf(" 0x%08x - 0x%08x : Non-ECC Area for DVC/AVC\n",
+ SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_ECC_SETTING * 2,
+ SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_SDRAM_ECC_SETTING * 2 +
+ SH7757LCR_SDRAM_DVC_SIZE - 1);
+ printf(" 0x%08x - 0x%08x : Non-ECC Area for G200eR2\n",
+ SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET,
+ SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET + 0x00ffffff);
+
+ return 0;
+}
+
+static int get_sh_eth_mac_raw(unsigned char *buf, int size)
+{
+ struct spi_flash *spi;
+ int ret;
+
+ spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
+ if (spi == NULL) {
+ printf("%s: spi_flash probe error.\n", __func__);
+ return 1;
+ }
+
+ ret = spi_flash_read(spi, SH7757LCR_ETHERNET_MAC_BASE, size, buf);
+ if (ret) {
+ printf("%s: spi_flash read error.\n", __func__);
+ spi_flash_free(spi);
+ return 1;
+ }
+ spi_flash_free(spi);
+
+ return 0;
+}
+
+static int get_sh_eth_mac(int channel, char *mac_string, unsigned char *buf)
+{
+ memcpy(mac_string, &buf[channel * (SH7757LCR_ETHERNET_MAC_SIZE + 1)],
+ SH7757LCR_ETHERNET_MAC_SIZE);
+ mac_string[SH7757LCR_ETHERNET_MAC_SIZE] = 0x00; /* terminate */
+
+ return 0;
+}
+
+static void init_ethernet_mac(void)
+{
+ char mac_string[64];
+ char env_string[64];
+ int i;
+ unsigned char *buf;
+
+ buf = malloc(256);
+ if (!buf) {
+ printf("%s: malloc error.\n", __func__);
+ return;
+ }
+ get_sh_eth_mac_raw(buf, 256);
+
+ /* Fast Ethernet */
+ for (i = 0; i < SH7757LCR_ETHERNET_NUM_CH; i++) {
+ get_sh_eth_mac(i, mac_string, buf);
+ if (i == 0)
+ setenv("ethaddr", mac_string);
+ else {
+ sprintf(env_string, "eth%daddr", i);
+ setenv(env_string, mac_string);
+ }
+
+ set_mac_to_sh_eth_register(i, mac_string);
+ }
+
+ /* Gigabit Ethernet */
+ for (i = 0; i < SH7757LCR_GIGA_ETHERNET_NUM_CH; i++) {
+ get_sh_eth_mac(i + SH7757LCR_ETHERNET_NUM_CH, mac_string, buf);
+ sprintf(env_string, "eth%daddr", i + SH7757LCR_ETHERNET_NUM_CH);
+ setenv(env_string, mac_string);
+
+ set_mac_to_sh_giga_eth_register(i, mac_string);
+ }
+
+ free(buf);
+}
+
+static void init_pcie(void)
+{
+ struct pcie_setup_regs *pcie_setup = PCIE_SETUP_BASE;
+ struct pcie_system_bus_regs *pcie_sysbus = PCIE_SYSTEM_BUS_BASE;
+
+ writel(0x00000ff2, &pcie_setup->ladmsk0);
+ writel(0x00000001, &pcie_setup->barmap);
+ writel(0xffcaa000, &pcie_setup->lad0);
+ writel(0x00030000, &pcie_sysbus->endictl0);
+ writel(0x00000003, &pcie_sysbus->endictl1);
+ writel(0x00000004, &pcie_setup->pbictl2);
+}
+
+static void finish_spiboot(void)
+{
+ struct gctrl_regs *gctrl = GCTRL_BASE;
+ /*
+ * SH7757 B0 does not use LBSC.
+ * So if we set SPIBOOTCAN to 1, SH7757 can not access Area0.
+ * This setting is not cleared by manual reset, So we have to set it
+ * to 0.
+ */
+ writel(0x00000000, &gctrl->spibootcan);
+}
+
+int board_late_init(void)
+{
+ init_ethernet_mac();
+ init_pcie_bridge();
+ init_pcie();
+ finish_spiboot();
+
+ return 0;
+}
+
+int do_sh_g200(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ struct gctrl_regs *gctrl = GCTRL_BASE;
+ unsigned long graofst;
+
+ writel(0xfedcba98, &gctrl->wprotect);
+ graofst = (SH7757LCR_SDRAM_PHYS_TOP + SH7757LCR_GRA_OFFSET) >> 24;
+ writel(graofst | 0xa0000f00, &gctrl->gracr3);
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ sh_g200, 1, 1, do_sh_g200,
+ "enable sh-g200",
+ "enable SH-G200 bus (disable PCIe-G200)"
+);
+
+int do_write_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int i, ret;
+ char mac_string[256];
+ struct spi_flash *spi;
+ unsigned char *buf;
+
+ if (argc != 5) {
+ buf = malloc(256);
+ if (!buf) {
+ printf("%s: malloc error.\n", __func__);
+ return 1;
+ }
+
+ get_sh_eth_mac_raw(buf, 256);
+
+ /* print current MAC address */
+ for (i = 0; i < 4; i++) {
+ get_sh_eth_mac(i, mac_string, buf);
+ if (i < 2)
+ printf(" ETHERC ch%d = %s\n", i, mac_string);
+ else
+ printf("GETHERC ch%d = %s\n", i-2, mac_string);
+ }
+ free(buf);
+ return 0;
+ }
+
+ /* new setting */
+ memset(mac_string, 0xff, sizeof(mac_string));
+ sprintf(mac_string, "%s\t%s\t%s\t%s",
+ argv[1], argv[2], argv[3], argv[4]);
+
+ /* write MAC data to SPI rom */
+ spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
+ if (!spi) {
+ printf("%s: spi_flash probe error.\n", __func__);
+ return 1;
+ }
+
+ ret = spi_flash_erase(spi, SH7757LCR_ETHERNET_MAC_BASE_SPI,
+ SH7757LCR_SPI_SECTOR_SIZE);
+ if (ret) {
+ printf("%s: spi_flash erase error.\n", __func__);
+ return 1;
+ }
+
+ ret = spi_flash_write(spi, SH7757LCR_ETHERNET_MAC_BASE_SPI,
+ sizeof(mac_string), mac_string);
+ if (ret) {
+ printf("%s: spi_flash write error.\n", __func__);
+ spi_flash_free(spi);
+ return 1;
+ }
+ spi_flash_free(spi);
+
+ puts("The writing of the MAC address to SPI ROM was completed.\n");
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ write_mac, 5, 1, do_write_mac,
+ "write MAC address for ETHERC/GETHERC",
+ "[ETHERC ch0] [ETHERC ch1] [GETHERC ch0] [GETHERC ch1]\n"
+);
--- /dev/null
+/*
+ * Copyright (C) 2011 Renesas Solutions Corp.
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License. See the file "COPYING.LIB" in the main
+ * directory of this archive for more details.
+ */
+
+#include <common.h>
+
+#define CONFIG_RAM_BOOT_PHYS 0x4ef80000
+#if defined(CONFIG_SH7757_OFFSET_SPI)
+#define CONFIG_SPI_ADDR 0x00010000
+#else
+#define CONFIG_SPI_ADDR 0x00000000
+#endif
+#define CONFIG_SPI_LENGTH 0x00030000
+#define CONFIG_RAM_BOOT 0x8ef80000
+
+#define SPIWDMADR 0xFE001018
+#define SPIWDMCNTR 0xFE001020
+#define SPIDMCOR 0xFE001028
+#define SPIDMINTSR 0xFE001188
+#define SPIDMINTMR 0xFE001190
+
+#define SPIDMINTSR_DMEND 0x00000004
+
+#define TBR 0xFE002000
+#define RBR 0xFE002000
+
+#define CR1 0xFE002008
+#define CR2 0xFE002010
+#define CR3 0xFE002018
+#define CR4 0xFE002020
+
+/* CR1 */
+#define SPI_TBE 0x80
+#define SPI_TBF 0x40
+#define SPI_RBE 0x20
+#define SPI_RBF 0x10
+#define SPI_PFONRD 0x08
+#define SPI_SSDB 0x04
+#define SPI_SSD 0x02
+#define SPI_SSA 0x01
+
+/* CR2 */
+#define SPI_RSTF 0x80
+#define SPI_LOOPBK 0x40
+#define SPI_CPOL 0x20
+#define SPI_CPHA 0x10
+#define SPI_L1M0 0x08
+
+/* CR4 */
+#define SPI_TBEI 0x80
+#define SPI_TBFI 0x40
+#define SPI_RBEI 0x20
+#define SPI_RBFI 0x10
+#define SPI_SSS 0x01
+
+#define spi_write(val, addr) (*(volatile unsigned long *)(addr)) = val
+#define spi_read(addr) (*(volatile unsigned long *)(addr))
+
+/* M25P80 */
+#define M25_READ 0x03
+
+#define __uses_spiboot2 __attribute__((section(".spiboot2.text")))
+static void __uses_spiboot2 spi_reset(void)
+{
+ spi_write(0xfe, CR1);
+
+ spi_write(0, SPIDMCOR);
+ spi_write(0x00, CR1);
+
+ spi_write(spi_read(CR2) | SPI_RSTF, CR2); /* fifo reset */
+ spi_write(spi_read(CR2) & ~SPI_RSTF, CR2);
+}
+
+static void __uses_spiboot2 spi_read_flash(void *buf, unsigned long addr,
+ unsigned long len)
+{
+ spi_write(M25_READ, TBR);
+ spi_write((addr >> 16) & 0xFF, TBR);
+ spi_write((addr >> 8) & 0xFF, TBR);
+ spi_write(addr & 0xFF, TBR);
+
+ spi_write(SPIDMINTSR_DMEND, SPIDMINTSR);
+ spi_write((unsigned long)buf, SPIWDMADR);
+ spi_write(len & 0xFFFFFFE0, SPIWDMCNTR);
+ spi_write(1, SPIDMCOR);
+
+ spi_write(0xff, CR3);
+ spi_write(spi_read(CR1) | SPI_SSDB, CR1);
+ spi_write(spi_read(CR1) | SPI_SSA, CR1);
+
+ while (!(spi_read(SPIDMINTSR) & SPIDMINTSR_DMEND))
+ ;
+}
+
+void __uses_spiboot2 spiboot_main(void)
+{
+ void (*_start)(void) = (void *)CONFIG_SYS_TEXT_BASE;
+
+ spi_reset();
+ spi_read_flash((void *)CONFIG_RAM_BOOT_PHYS, CONFIG_SPI_ADDR,
+ CONFIG_SPI_LENGTH);
+
+ _start();
+}
+
--- /dev/null
+/*
+ * Copyright (C) 2007
+ * Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ *
+ * Copyright (C) 2011
+ * Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-sh-linux", "elf32-sh-linux", "elf32-sh-linux")
+OUTPUT_ARCH(sh)
+ENTRY(_start)
+
+SECTIONS
+{
+ /*
+ * entry and reloct_dst will be provided via ldflags
+ */
+ . = .;
+
+ PROVIDE (_ftext = .);
+ PROVIDE (_fcode = .);
+ PROVIDE (_start = .);
+
+ .text :
+ {
+ arch/sh/cpu/sh4/start.o (.text)
+ *(.spiboot1.text)
+ *(.spiboot2.text)
+ . = ALIGN(8192);
+ common/env_embedded.o (.ppcenv)
+ . = ALIGN(8192);
+ common/env_embedded.o (.ppcenvr)
+ . = ALIGN(8192);
+ *(.text)
+ . = ALIGN(4);
+ } =0xFF
+ PROVIDE (_ecode = .);
+ .rodata :
+ {
+ *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
+ . = ALIGN(4);
+ }
+ PROVIDE (_etext = .);
+
+
+ PROVIDE (_fdata = .);
+ .data :
+ {
+ *(.data)
+ . = ALIGN(4);
+ }
+ PROVIDE (_edata = .);
+
+ PROVIDE (_fgot = .);
+ .got :
+ {
+ *(.got)
+ . = ALIGN(4);
+ }
+ PROVIDE (_egot = .);
+
+ PROVIDE (__u_boot_cmd_start = .);
+ .u_boot_cmd :
+ {
+ *(.u_boot_cmd)
+ . = ALIGN(4);
+ }
+ PROVIDE (__u_boot_cmd_end = .);
+
+ PROVIDE (reloc_dst_end = .);
+ /* _reloc_dst_end = .; */
+
+ PROVIDE (bss_start = .);
+ PROVIDE (__bss_start = .);
+ .bss (NOLOAD) :
+ {
+ *(.bss)
+ . = ALIGN(4);
+ }
+ PROVIDE (bss_end = .);
+
+ PROVIDE (_end = .);
+}
+++ /dev/null
-#
-# board/sh7763rdp/config.mk
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x8FFC0000
-
-# PLATFORM_CPPFLAGS += -DCONFIG_MULTIBOOT
COBJS := sh7785lcr.o selfcheck.o rtl8169_mac.o
SOBJS := lowlevel_init.o
-$(LIB): $(obj).depend $(COBJS) $(SOBJS)
- $(call cmd_link_o_target, $(COBJS) $(SOBJS))
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
clean:
rm -f $(SOBJS) $(OBJS)
+++ /dev/null
-#
-# Copyright (C) 2007
-# Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# CONFIG_SYS_TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
-
-ifdef CONFIG_SH_32BIT
-CONFIG_SYS_TEXT_BASE = 0x8FF80000
-else
-CONFIG_SYS_TEXT_BASE = 0x0ff80000
-endif
+++ /dev/null
-#
-# Copyright (C) 2010 Nobuhiro Iwamatsu
-#
-# u-boot/board/shmin/config.mk
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-
-#
-# TEXT_BASE refers to image _after_ relocation.
-#
-# NOTE: Must match value used in u-boot.lds (in this directory).
-#
-
-CONFIG_SYS_TEXT_BASE = 0x8DFB0000
ap325rxa sh sh4 ap325rxa renesas -
r2dplus sh sh4 r2dplus renesas -
r7780mp sh sh4 r7780mp renesas -
+sh7757lcr sh sh4 sh7757lcr renesas -
sh7763rdp sh sh4 sh7763rdp renesas -
sh7785lcr sh sh4 sh7785lcr renesas -
sh7785lcr_32bit sh sh4 sh7785lcr renesas - sh7785lcr:SH_32BIT=1
--- /dev/null
+========================================
+Renesas R0P7757LC0030RL board
+========================================
+
+This board specification:
+=========================
+
+The R0P7757LC0030RL(board config name:sh7757lcr) has the following device:
+
+ - SH7757 (SH-4A)
+ - DDR3-SDRAM 256MB (with ECC)
+ - SPI ROM 8MB
+ - 2D Graphic controller
+ - Ethernet controller
+
+
+configuration for This board:
+=============================
+
+You can select the configuration as follows:
+
+ - make sh7785lcr_config
+
+
+This board specific command:
+============================
+
+This board has the following its specific command:
+
+ - sh_g200
+ - write_mac
+
+
+1. sh_g200
+
+If we run this command, SH4 can control the G200.
+The default setting is that SH4 cannot control the G200.
+
+
+2. write_mac
+
+You can write MAC address to SPI ROM.
+
+ Usage 1) Write MAC address
+
+ write_mac [ETHERC ch0] [ETHERC ch1] [GETHERC ch0] [GETHERC ch1]
+
+ For example)
+ => write_mac 00:00:87:6c:21:80 00:00:87:6c:21:81 00:00:87:6c:21:82 00:00:87:6c:21:83
+ *) We have to input the command as a single line
+ (without carriage return)
+ *) We have to reset after input the command.
+
+ Usage 2) Show current data
+
+ write_mac
+
+ For example)
+ => write_mac
+ ETHERC ch0 = 00:00:87:6c:21:80
+ ETHERC ch1 = 00:00:87:6c:21:81
+ GETHERC ch0 = 00:00:87:6c:21:82
+ GETHERC ch1 = 00:00:87:6c:21:83
+
#ifndef CONFIG_SH_ETHER_PHY_ADDR
# error "Please define CONFIG_SH_ETHER_PHY_ADDR"
#endif
+#ifdef CONFIG_SH_ETHER_CACHE_WRITEBACK
+#define flush_cache_wback(addr, len) \
+ dcache_wback_range((u32)addr, (u32)(addr + len - 1))
+#else
+#define flush_cache_wback(...)
+#endif
#define SH_ETH_PHY_DELAY 50000
}
/* Update tx descriptor */
+ flush_cache_wback(packet, len);
port_info->tx_desc_cur->td2 = ADDR_TO_PHY(packet);
port_info->tx_desc_cur->td1 = len << 16;
/* Must preserve the end of descriptor list indication */
tmp_addr = (u32) (((int)port_info->tx_desc_malloc + TX_DESC_SIZE - 1) &
~(TX_DESC_SIZE - 1));
+ flush_cache_wback(tmp_addr, NUM_TX_DESC * sizeof(struct tx_desc_s));
/* Make sure we use a P2 address (non-cacheable) */
port_info->tx_desc_base = (struct tx_desc_s *)ADDR_TO_P2(tmp_addr);
port_info->tx_desc_cur = port_info->tx_desc_base;
tmp_addr = (u32) (((int)port_info->rx_desc_malloc + RX_DESC_SIZE - 1) &
~(RX_DESC_SIZE - 1));
+ flush_cache_wback(tmp_addr, NUM_RX_DESC * sizeof(struct rx_desc_s));
/* Make sure we use a P2 address (non-cacheable) */
port_info->rx_desc_base = (struct rx_desc_s *)ADDR_TO_P2(tmp_addr);
COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o
COBJS-$(CONFIG_OMAP3_SPI) += omap3_spi.o
COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o
+COBJS-$(CONFIG_SH_SPI) += sh_spi.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
--- /dev/null
+/*
+ * SH SPI driver
+ *
+ * Copyright (C) 2011 Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ *
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <spi.h>
+#include <asm/io.h>
+#include "sh_spi.h"
+
+static void sh_spi_write(unsigned long data, unsigned long *reg)
+{
+ writel(data, reg);
+}
+
+static unsigned long sh_spi_read(unsigned long *reg)
+{
+ return readl(reg);
+}
+
+static void sh_spi_set_bit(unsigned long val, unsigned long *reg)
+{
+ unsigned long tmp;
+
+ tmp = sh_spi_read(reg);
+ tmp |= val;
+ sh_spi_write(tmp, reg);
+}
+
+static void sh_spi_clear_bit(unsigned long val, unsigned long *reg)
+{
+ unsigned long tmp;
+
+ tmp = sh_spi_read(reg);
+ tmp &= ~val;
+ sh_spi_write(tmp, reg);
+}
+
+static void clear_fifo(struct sh_spi *ss)
+{
+ sh_spi_set_bit(SH_SPI_RSTF, &ss->regs->cr2);
+ sh_spi_clear_bit(SH_SPI_RSTF, &ss->regs->cr2);
+}
+
+static int recvbuf_wait(struct sh_spi *ss)
+{
+ while (sh_spi_read(&ss->regs->cr1) & SH_SPI_RBE) {
+ if (ctrlc())
+ return 1;
+ udelay(10);
+ }
+ return 0;
+}
+
+static int write_fifo_empty_wait(struct sh_spi *ss)
+{
+ while (!(sh_spi_read(&ss->regs->cr1) & SH_SPI_TBE)) {
+ if (ctrlc())
+ return 1;
+ udelay(10);
+ }
+ return 0;
+}
+
+void spi_init(void)
+{
+}
+
+struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
+ unsigned int max_hz, unsigned int mode)
+{
+ struct sh_spi *ss;
+
+ if (!spi_cs_is_valid(bus, cs))
+ return NULL;
+
+ ss = malloc(sizeof(struct spi_slave));
+ if (!ss)
+ return NULL;
+
+ ss->slave.bus = bus;
+ ss->slave.cs = cs;
+ ss->regs = (struct sh_spi_regs *)CONFIG_SH_SPI_BASE;
+
+ /* SPI sycle stop */
+ sh_spi_write(0xfe, &ss->regs->cr1);
+ /* CR1 init */
+ sh_spi_write(0x00, &ss->regs->cr1);
+ /* CR3 init */
+ sh_spi_write(0x00, &ss->regs->cr3);
+
+ clear_fifo(ss);
+
+ /* 1/8 clock */
+ sh_spi_write(sh_spi_read(&ss->regs->cr2) | 0x07, &ss->regs->cr2);
+ udelay(10);
+
+ return &ss->slave;
+}
+
+void spi_free_slave(struct spi_slave *slave)
+{
+ struct sh_spi *spi = to_sh_spi(slave);
+
+ free(spi);
+}
+
+int spi_claim_bus(struct spi_slave *slave)
+{
+ return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+ struct sh_spi *ss = to_sh_spi(slave);
+
+ sh_spi_write(sh_spi_read(&ss->regs->cr1) &
+ ~(SH_SPI_SSA | SH_SPI_SSDB | SH_SPI_SSD), &ss->regs->cr1);
+}
+
+static int sh_spi_send(struct sh_spi *ss, const unsigned char *tx_data,
+ unsigned int len, unsigned long flags)
+{
+ int i, cur_len, ret = 0;
+ int remain = (int)len;
+ unsigned long tmp;
+
+ if (len >= SH_SPI_FIFO_SIZE)
+ sh_spi_set_bit(SH_SPI_SSA, &ss->regs->cr1);
+
+ while (remain > 0) {
+ cur_len = (remain < SH_SPI_FIFO_SIZE) ?
+ remain : SH_SPI_FIFO_SIZE;
+ for (i = 0; i < cur_len &&
+ !(sh_spi_read(&ss->regs->cr4) & SH_SPI_WPABRT) &&
+ !(sh_spi_read(&ss->regs->cr1) & SH_SPI_TBF);
+ i++)
+ sh_spi_write(tx_data[i], &ss->regs->tbr_rbr);
+
+ cur_len = i;
+
+ if (sh_spi_read(&ss->regs->cr4) & SH_SPI_WPABRT) {
+ /* Abort the transaction */
+ flags |= SPI_XFER_END;
+ sh_spi_set_bit(SH_SPI_WPABRT, &ss->regs->cr4);
+ ret = 1;
+ break;
+ }
+
+ remain -= cur_len;
+ tx_data += cur_len;
+
+ if (remain > 0)
+ write_fifo_empty_wait(ss);
+ }
+
+ if (flags & SPI_XFER_END) {
+ tmp = sh_spi_read(&ss->regs->cr1);
+ tmp = tmp & ~(SH_SPI_SSD | SH_SPI_SSDB);
+ sh_spi_write(tmp, &ss->regs->cr1);
+ sh_spi_set_bit(SH_SPI_SSA, &ss->regs->cr1);
+ udelay(100);
+ write_fifo_empty_wait(ss);
+ }
+
+ return ret;
+}
+
+static int sh_spi_receive(struct sh_spi *ss, unsigned char *rx_data,
+ unsigned int len, unsigned long flags)
+{
+ int i;
+ unsigned long tmp;
+
+ if (len > SH_SPI_MAX_BYTE)
+ sh_spi_write(SH_SPI_MAX_BYTE, &ss->regs->cr3);
+ else
+ sh_spi_write(len, &ss->regs->cr3);
+
+ tmp = sh_spi_read(&ss->regs->cr1);
+ tmp = tmp & ~(SH_SPI_SSD | SH_SPI_SSDB);
+ sh_spi_write(tmp, &ss->regs->cr1);
+ sh_spi_set_bit(SH_SPI_SSA, &ss->regs->cr1);
+
+ for (i = 0; i < len; i++) {
+ if (recvbuf_wait(ss))
+ return 0;
+
+ rx_data[i] = (unsigned char)sh_spi_read(&ss->regs->tbr_rbr);
+ }
+ sh_spi_write(0, &ss->regs->cr3);
+
+ return 0;
+}
+
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
+ void *din, unsigned long flags)
+{
+ struct sh_spi *ss = to_sh_spi(slave);
+ const unsigned char *tx_data = dout;
+ unsigned char *rx_data = din;
+ unsigned int len = bitlen / 8;
+ int ret = 0;
+
+ if (flags & SPI_XFER_BEGIN)
+ sh_spi_write(sh_spi_read(&ss->regs->cr1) & ~SH_SPI_SSA,
+ &ss->regs->cr1);
+
+ if (tx_data)
+ ret = sh_spi_send(ss, tx_data, len, flags);
+
+ if (ret == 0 && rx_data)
+ ret = sh_spi_receive(ss, rx_data, len, flags);
+
+ if (flags & SPI_XFER_END) {
+ sh_spi_set_bit(SH_SPI_SSD, &ss->regs->cr1);
+ udelay(100);
+
+ sh_spi_clear_bit(SH_SPI_SSA | SH_SPI_SSDB | SH_SPI_SSD,
+ &ss->regs->cr1);
+ clear_fifo(ss);
+ }
+
+ return ret;
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ /* This driver supports "bus = 0" and "cs = 0" only. */
+ if (!bus && !cs)
+ return 1;
+ else
+ return 0;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+
+}
+
--- /dev/null
+/*
+ * SH SPI driver
+ *
+ * Copyright (C) 2011 Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ *
+ */
+
+#ifndef __SH_SPI_H__
+#define __SH_SPI_H__
+
+#include <spi.h>
+
+struct sh_spi_regs {
+ unsigned long tbr_rbr;
+ unsigned long resv1;
+ unsigned long cr1;
+ unsigned long resv2;
+ unsigned long cr2;
+ unsigned long resv3;
+ unsigned long cr3;
+ unsigned long resv4;
+ unsigned long cr4;
+};
+
+/* CR1 */
+#define SH_SPI_TBE 0x80
+#define SH_SPI_TBF 0x40
+#define SH_SPI_RBE 0x20
+#define SH_SPI_RBF 0x10
+#define SH_SPI_PFONRD 0x08
+#define SH_SPI_SSDB 0x04
+#define SH_SPI_SSD 0x02
+#define SH_SPI_SSA 0x01
+
+/* CR2 */
+#define SH_SPI_RSTF 0x80
+#define SH_SPI_LOOPBK 0x40
+#define SH_SPI_CPOL 0x20
+#define SH_SPI_CPHA 0x10
+#define SH_SPI_L1M0 0x08
+
+/* CR3 */
+#define SH_SPI_MAX_BYTE 0xFF
+
+/* CR4 */
+#define SH_SPI_TBEI 0x80
+#define SH_SPI_TBFI 0x40
+#define SH_SPI_RBEI 0x20
+#define SH_SPI_RBFI 0x10
+#define SH_SPI_WPABRT 0x04
+#define SH_SPI_SSS 0x01
+
+#define SH_SPI_FIFO_SIZE 32
+
+struct sh_spi {
+ struct spi_slave slave;
+ struct sh_spi_regs *regs;
+};
+
+static inline struct sh_spi *to_sh_spi(struct spi_slave *slave)
+{
+ return container_of(slave, struct sh_spi, slave);
+}
+
+#endif
+
#define MIGO_R_FLASH_BASE_1 (0xA0000000)
#define MIGO_R_FLASH_BANK_SIZE (64 * 1024 * 1024)
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */
#define AP325RXA_FLASH_BASE_1 (0xA0000000)
#define AP325RXA_FLASH_BANK_SIZE (128 * 1024 * 1024)
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
+
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
#define CONFIG_BAUDRATE 115200
#define CONFIG_CONS_SCIF0 1
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */
#define CONFIG_SYS_MONITOR_LEN (128 * 1024)
#define CONFIG_SYS_MALLOC_LEN (256 * 1024)
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
+
/* Memory */
#define CONFIG_SYS_SDRAM_BASE 0x8C000000
#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024)
#define MS7720SE_FLASH_BASE_1 0xA0000000
#define MS7720SE_FLASH_BANK_SIZE (8 * 1024 * 1024)
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */
#define MS7722SE_FLASH_BASE_1 (0xA0000000)
#define MS7722SE_FLASH_BANK_SIZE (8*1024 * 1024)
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */
/* List of legal baudrate settings for this board */
#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 57600, 38400, 19200, 9600 }
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - 0x100000)
#define CONFIG_SYS_SDRAM_BASE (0x8C000000)
#define CONFIG_SYS_SDRAM_SIZE (0x04000000)
+#define CONFIG_SYS_TEXT_BASE 0x0FFC0000
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_PROMPT "=> "
#define CONFIG_SYS_CBSIZE 256
/* check for keypress on bootdelay==0 */
/*#define CONFIG_ZERO_BOOTDELAY_CHECK*/
+#define CONFIG_SYS_TEXT_BASE 0x0FFC0000
#define CONFIG_SYS_SDRAM_BASE (0x08000000)
#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024)
#define RSK7203_FLASH_BASE_1 0x20000000 /* Non cache */
#define RSK7203_FLASH_BANK_SIZE (4 * 1024 * 1024)
+#define CONFIG_SYS_TEXT_BASE 0x0C7C0000
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */
--- /dev/null
+/*
+ * Configuation settings for the sh7757lcr board
+ *
+ * Copyright (C) 2011 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __SH7757LCR_H
+#define __SH7757LCR_H
+
+#undef DEBUG
+#define CONFIG_SH 1
+#define CONFIG_SH4A 1
+#define CONFIG_SH_32BIT 1
+#define CONFIG_CPU_SH7757 1
+#define CONFIG_SH7757LCR 1
+
+#define CONFIG_SYS_TEXT_BASE 0x8ef80000
+#define CONFIG_SYS_LDSCRIPT "board/renesas/sh7757lcr/u-boot.lds"
+
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_DFL
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_MD5SUM
+#define CONFIG_MD5
+#define CONFIG_CMD_LOADS
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "console=ttySC2,115200 root=/dev/nfs ip=dhcp"
+
+#define CONFIG_VERSION_VARIABLE
+#undef CONFIG_SHOW_BOOT_PROGRESS
+
+/* MEMORY */
+#define SH7757LCR_SDRAM_BASE (0x80000000)
+#define SH7757LCR_SDRAM_SIZE (240 * 1024 * 1024)
+#define SH7757LCR_SDRAM_ECC_SETTING 0x0f000000 /* 240MByte */
+#define SH7757LCR_SDRAM_DVC_SIZE (16 * 1024 * 1024)
+
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE 512
+#define CONFIG_SYS_BAUDRATE_TABLE { 115200 }
+
+/* SCIF */
+#define CONFIG_SCIF_CONSOLE 1
+#define CONFIG_CONS_SCIF2 1
+#undef CONFIG_SYS_CONSOLE_INFO_QUIET
+#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
+
+#define CONFIG_SYS_MEMTEST_START (SH7757LCR_SDRAM_BASE)
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
+ 224 * 1024 * 1024)
+#undef CONFIG_SYS_ALT_MEMTEST
+#undef CONFIG_SYS_MEMTEST_SCRATCH
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE
+
+#define CONFIG_SYS_SDRAM_BASE (SH7757LCR_SDRAM_BASE)
+#define CONFIG_SYS_SDRAM_SIZE (SH7757LCR_SDRAM_SIZE)
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + \
+ (128 + 16) * 1024 * 1024)
+
+#define CONFIG_SYS_MONITOR_BASE 0x00000000
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
+
+/* FLASH */
+#define CONFIG_SYS_NO_FLASH
+
+/* Ether */
+#define CONFIG_NET_MULTI 1
+#define CONFIG_SH_ETHER 1
+#define CONFIG_SH_ETHER_USE_PORT 0
+#define CONFIG_SH_ETHER_PHY_ADDR 1
+#define CONFIG_SH_ETHER_CACHE_WRITEBACK 1
+
+#define SH7757LCR_ETHERNET_MAC_BASE_SPI 0x000b0000
+#define SH7757LCR_SPI_SECTOR_SIZE (64 * 1024)
+#define SH7757LCR_ETHERNET_MAC_BASE SH7757LCR_ETHERNET_MAC_BASE_SPI
+#define SH7757LCR_ETHERNET_MAC_SIZE 17
+#define SH7757LCR_ETHERNET_NUM_CH 2
+#define BOARD_LATE_INIT 1
+
+/* Gigabit Ether */
+#define SH7757LCR_GIGA_ETHERNET_NUM_CH 2
+
+/* SPI */
+#define CONFIG_SH_SPI 1
+#define CONFIG_SH_SPI_BASE 0xfe002000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO 1
+
+/* SH7757 board */
+#define SH7757LCR_SDRAM_PHYS_TOP 0x40000000
+#define SH7757LCR_GRA_OFFSET 0x1f000000
+#define SH7757LCR_PCIEBRG_ADDR_B0 0x000a0000
+#define SH7757LCR_PCIEBRG_SIZE_B0 (64 * 1024)
+#define SH7757LCR_PCIEBRG_ADDR 0x00090000
+#define SH7757LCR_PCIEBRG_SIZE (96 * 1024)
+
+/* ENV setting */
+#define CONFIG_ENV_IS_EMBEDDED
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SECT_SIZE (64 * 1024)
+#define CONFIG_ENV_ADDR (0x00080000)
+#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR)
+#define CONFIG_ENV_OVERWRITE 1
+#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netboot=bootp; bootm\0"
+
+/* Board Clock */
+#define CONFIG_SYS_CLK_FREQ 48000000
+#define CONFIG_SYS_TMU_CLK_DIV 4
+#define CONFIG_SYS_HZ 1000
+#endif /* __SH7757LCR_H */
#define CONFIG_BAUDRATE 115200
#define CONFIG_CONS_SCIF2 1
+#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */
/* MEMORY */
#if defined(CONFIG_SH_32BIT)
+#define CONFIG_SYS_TEXT_BASE 0x8FF80000
/* 0x40000000 - 0x47FFFFFF does not use */
#define CONFIG_SH_SDRAM_OFFSET (0x8000000)
#define SH7785LCR_SDRAM_PHYS_BASE (0x40000000 + CONFIG_SH_SDRAM_OFFSET)
#define SH7785LCR_FLASH_BANK_SIZE (64 * 1024 * 1024)
#define SH7785LCR_USB_BASE (0xa6000000)
#else
+#define CONFIG_SYS_TEXT_BASE 0x0FF80000
#define SH7785LCR_SDRAM_BASE (0x08000000)
#define SH7785LCR_SDRAM_SIZE (128 * 1024 * 1024)
#define SH7785LCR_FLASH_BASE_1 (0xa0000000)
#define SHMIN_SDRAM_BASE (0x8C000000)
#define SHMIN_FLASH_BASE_1 (0xA0000000)
+#define CONFIG_SYS_TEXT_BASE 0x8DFB0000
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Buffer size for input from the Console */
projects / karo-tx-uboot.git / commitdiff