David S. Miller [Sat, 9 May 2015 20:27:04 +0000 (16:27 -0400)]
Merge branch 'be2net'
Sathya Perla says:
====================
be2net: patch-set
The following patch-set has two new feature additions, and a few
minor fixes and cleanups.
Pls consider applying to the net-next tree. Thanks.
v2 changes:
a) dropped the "don't enable pause by default" patch
b) described how the "spoof check" works in patch 1's commit log
c) I had to update our email addresses from "@emulex" to
"@avagotech". I'll send a separate patch updating the
maintainers
Patch 1 adds support for the "spoofchk" knob for VFs.
When it is enabled, "spoof checking" is done for both MAC-address
and VLAN. For each VF, the HW ensures that the source MAC address
(or vlan) of every outgoing packet of the VF exists in the MAC-list
(or vlan-list) configured for RX filtering for that VF.
If not, the packet is dropped and an error is reported to the driver
in the TX completion.
Patch 2 improves interrupt moderation on Skyhawk-R chip by using
the EQ-DB mechanism to set a "re-arm to interrupt" delay. Currently
interrupt moderation is adjusted by calculating and configuring an
EQ-delay every second. This is done via a FW-cmd. This patch uses
the EQ_DB facility to calculate and set the interrupt delay every 1ms.
This helps moderating interrupts better when the traffic is bursty.
Patch 3 adds L3/L4 error accounting to BE3 VFs, by passing L3/4 error
packets to the network stack.
Patch 4 adds an extra FW-cmd error value check in the driver to identify
an "out of vlan filters" scenario.
Patch 5 stops enabling pause by default as this setting fails in
some HW-configs where priority pause is enabled in FW. If the user
tries to do the same, an appropriate error is returned via ethtool.
Patch 5 posts the full RXQ in be_open() to prevent packet drops due to
bursty traffic when the interface is enabled.
Patch 6 refactors the be_check_ufi_compatibility() routine, that checks
to see if a UFI file meant for a lower rev of a chip is being flashed
on a higher rev, to make it simpler.
Patch 7 replaces the usage of !be_physfn() macro with be_virtfn()
that is already avialble in the driver.
Patch 8 updates the year in the copyright text to 2015.
Path 9 bumps up the driver version to 10.6.02.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The code in be_check_ufi_compatibility() checks to see if a UFI file meant
for a lower rev of a chip is being flashed on a higher rev, which is
disallowed. This patch re-writes the code needed for this check in a much
simpler manner.
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Wed, 6 May 2015 09:30:36 +0000 (05:30 -0400)]
be2net: post full RXQ on interface enable
When an RXQ is created in be_open(), the driver currently posts only
64 buffers. This sometimes results in packet drops when there is a traffic
burst as soon as the interface is enabled.
This patch fixes this problem by posting the full RXQ on interface enable.
Signed-off-by: Suresh Reddy <Suresh.Reddy@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Wed, 6 May 2015 09:30:35 +0000 (05:30 -0400)]
be2net: check for INSUFFICIENT_VLANS error
When the FW runs out of vlan filters it can either return an
INSUFFICIENT_RESOURCES error or an INSUFFICIENT_VLANS error.
The driver currently checks only for the former error value.
This patch adds a check for the latter value too.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Wed, 6 May 2015 09:30:34 +0000 (05:30 -0400)]
be2net: receive pkts with L3, L4 errors on VFs
Currently pkts with L3 or L4 errors received on PFs are not dropped
by the adapter, but instead sent to the stack. This helps the network stack
to better reflect error statistics. This was not being done on BE3 VFs.
This patch fixes this for BE3 VFs.
Signed-off-by: Somnath Kotur <somnath.kotur@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: set interrupt moderation for Skyhawk-R using EQ-DB
Currently adaptive interrupt moderation is set by calculating
and configuring an EQ-delay every second. This is done via
a FW-cmd. But, on Skyhawk-R a "re-arm to interrupt" delay
can be set while ringing the EQ-DB. This patch uses this
facility to calculate and set the interrupt delay every 1ms.
This helps moderating interrupts better when the traffic
is bursty.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Wed, 6 May 2015 09:30:32 +0000 (05:30 -0400)]
be2net: add support for spoofchk setting
This patch adds support for spoofchk configuration for VFs.
When it is enabled, "spoof checking" is done for both MAC-address and VLAN.
For each VF, the HW ensures that the source MAC address (or vlan) of
every outgoing packet exists in the MAC-list (or vlan-list) configured
for RX filtering for that VF. If not, the packet is dropped and an error
is reported to the driver in the TX completion; this is reflected in the
"tx_spoof_check_err" ethtool counter.
This feature is supported in Skyhawk FW version 10.6.31.0 and above.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 9 May 2015 20:16:49 +0000 (16:16 -0400)]
Merge branch 'sfc-next'
Shradha Shah says:
====================
sfc: Enabling EF10 Vf's, set up vswitching and bind the SFC driver to the VF's
This set of patches makes way for the implementation of EF10
SR-IOV driver starting with some cleanup code.
NIC specific SR-IOV functions are moved to their own header
and netdev_ops are made generic instead of being NIC specific
Next in line comes the patch to enable VF's using sriov_configure.
VEB vswitching hierarchy is set up next followed by patches to
prepare sfc driver to bind to enabled VF's
This is followed by patch to support use of shared RSS contexts
which makes VF's use shared RSS contexts in all cases.
Patch series ends with a patch to bind the sfc driver to the
enabled VF's which creates network interfaces corresponding to
the VF's.
Coming up soon are the patches to set_vf_mac, set_vf_config,
set_vf_vlan, vf_spoofcheck, etc.
These patches have been tested with and without CONFIG_SFC_SRIOV.
In the case of CONFIG_SFC_SRIOV=y enabling of VF's using
sriov_configure is also tested. The enabled VF's bind to the
installed sfc driver succesfully to create network interfaces.
In the case of CONFIG_SFC_SRIOV=n enabling of VF's using
sriov_configure returns the correct error message:
"Function not implemented".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shradha Shah [Wed, 6 May 2015 00:00:07 +0000 (01:00 +0100)]
sfc: Bind the sfc driver to any available VF's
Add the device ID of the VF to the PCI device ID table.
Added a boolean flag is_vf in efx_nic_type to differentiate
between a VF and PF at probe time. This flag is useful in later
patches while setting MAC address specially in the
PCI-passthrough case.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Cooper [Tue, 5 May 2015 23:59:38 +0000 (00:59 +0100)]
sfc: Add use of shared RSS contexts.
Allow PFs to allocate shared RSS contexts if we exhaust our
exclusive RSS contexts. Make VFs use shared RSS contexts in
all cases.
Spruce up error handling so that the shadow copy of the RSS
table is updated after successful update, rather than in all
cases, so that we report the actual contents of the RSS table
after a failure to set it, rather than what we'd like it to be.
Populate context_size parameter when vacuously allocating RSS
context of size 1.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Tue, 5 May 2015 23:59:18 +0000 (00:59 +0100)]
sfc: Cope with permissions enforcement added to firmware for SR-IOV
* Accept EPERM in some simple cases, the following cases are handled:
1) efx_mcdi_read_assertion()
Unprivileged PCI functions aren't allowed to GET_ASSERTS.
We return success as it's up to the primary PF to deal with asserts.
2) efx_mcdi_mon_probe() in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to read sensor info, and
worrying about sensor data is the primary PF's job.
3) phy_op->reconfigure() in efx_init_port() and efx_reset_up()
Unprivileged functions aren't allowed to MC_CMD_SET_LINK, they just have
to accept the settings (including flow-control, which is what
efx_init_port() is worried about) they've been given.
4) Fallback to GET_WORKAROUNDS in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to set workarounds. So if
efx_mcdi_set_workaround() fails EPERM, use efx_mcdi_get_workarounds()
to find out if workaround_35388 is enabled.
5) If DRV_ATTACH gets EPERM, try without specifying fw-variant
Unprivileged PCI functions have to use a FIRMWARE_ID of 0xffffffff
(MC_CMD_FW_DONT_CARE).
6) Don't try to exit_assertion unless one had fired
Previously we called efx_mcdi_exit_assertion even if
efx_mcdi_read_assertion had received MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS.
This is unnecessary, and the resulting MC_CMD_REBOOT, even if the
AFTER_ASSERTION flag made it a no-op, would fail EPERM for unprivileged
PCI functions.
So make efx_mcdi_read_assertion return whether an assert happened, and only
call efx_mcdi_exit_assertion if it has.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shradha Shah [Tue, 5 May 2015 23:58:54 +0000 (00:58 +0100)]
sfc: manually allocate and free vadaptors
To be able to use MC_CMD_VADAPTOR_SET_MAC, vadaptors must be
manually allocated and freed as automatic vadaptors will disappear
when their reference_count reaches zero, which must happen before
the MAC address is changed.
Vadaptors are allocated and freed in the vswitching_probe/remove
functions for PFs and VFs, and this means that vadaptors are restored
correctly following an MC reboot or other reset when required.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shradha Shah [Tue, 5 May 2015 23:58:31 +0000 (00:58 +0100)]
sfc: create vports for VFs and assign random MAC addresses
The parent PF creates vports for all its child VFs and adds MAC
addresses to these. When the VF driver loads, it can make an MCDI
call to get the MAC address that the parent PF assigned it.
The parent PF also assigns a mac address to its own vport because
implicit creation of a vAdaptor will only work on evb ports with
MAC addresses assigned.
The vport MAC address needs to be stored in the PF's nic_data
struct as it can later be changed on the vadaptor (and its net_dev
struct). When removing a vport the original MAC address must be
deleted.
A new flag is needed in the VF data structure to identify whether
a vport has been assigned to the VF. This is to determine whether
it needs to be un-assigned before freeing the vport. Also,
attempting to un-assign a vport which is not assigned will result
in an EALREADY error.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Pieczko [Tue, 5 May 2015 23:57:34 +0000 (00:57 +0100)]
sfc: create VEB vswitch and vport above default firmware setup
Adds functions to allocate and free vswitches and vports; vadaptors
are automatically allocated and freed when TX/RX queues are
initialised and finalised. This vswitching structure is only created
if the firmware supports it, so a check that full-featured firmware
is running is performed first.
If the MC resets, the vswitching infrastructure will need to be
recreated, so mark the "must_probe_vswitching" flag when an MC reboot
is detected.
Don't try to create a vswitch if vf-count=0
This allocation of vswitches and vports does not currently support
configuring VLAN tags, but that can be added in a future change.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Pieczko [Tue, 5 May 2015 23:57:14 +0000 (00:57 +0100)]
sfc: record the PF's vport ID in nic_data
The default port ID of EVB_PORT_ID_ASSIGNED is a "magic" number
for the MCFW to select the physical port of the PF. If other
vswitches and vports are created on top of the default firmware
configuration, the ID of the newly created vport is then required
when passed to MCDI commands. Currently, this doesn't happen so
the vport_id is never changed, but a subsequent patch will change
this behaviour so that other vswitches and vports are created.
The vport_id recorded in nic_data is only relevant for PFs.
VFs will have their vports created by their parent PF, and in
that case the parent PF will record the vport ID of each VF.
For a VF, nic_data->vport_id is expected to remain at the default
value.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Pieczko [Tue, 5 May 2015 23:56:55 +0000 (00:56 +0100)]
sfc: Record [rt]x_dpcpu_fw_id in EF10 nic_data
The (future) code to add/remove vswitches and vports will be
dependent on the firmware variant.
To simplify the checking of the firmware variant, record
values for rx_dpcpu_fw_id and tx_dpcpu_fw_id in EF10 nic_data.
There was only one place where this was previously used:
efx_mcdi_print_fwver() in ethtool.c.
The MC_CMD_GET_CAPABILITIES can be replaced and the values from
nic_data used instead.
Note that the printing of "?" if the MC command fails or if the
outlength is incorrect no longer apply, because errors are returned
in efx_ef10_init_datapath_caps() in both of these cases.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Pieczko [Tue, 5 May 2015 23:55:36 +0000 (00:55 +0100)]
sfc: Move and rename efx_vf struct to siena_vf
The efx_vf struct contains Siena-specific fields for VFs,
so rename to siena_vf.
Also move it into the siena_nic_data struct, as EF10 will
track its VFs in its own ef10_nic_data, storing much less
information about them since VFDI is no longer used.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shradha Shah [Tue, 5 May 2015 23:55:13 +0000 (00:55 +0100)]
sfc: Own header for nic-specific sriov functions, single instance of netdev_ops and sriov removed from Falcon code
By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.
The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.
Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 9 May 2015 20:05:54 +0000 (16:05 -0400)]
Merge branch 'dsa-next'
Andrew Lunn says:
====================
More Marvell DSA refactring and fixup
This patch setup continues the refactoring and cleanup of the Marvell
DSA drivers.
Patch #1 Centralizes the duplicated parts of port setup and global
setup into the shared mv88e6xxx.
Patch #2 Centralizes looping over the ports setting them up
Patch #3 Uses mnemonics for the remaining register access in the
drivers.
Patch #4 The 6172 is actually a member of the 6352 family. This moves
the probe code into the correct driver.
Patch #5 Adds more members of the 6171 family to the 6171 driver. The
new devices are untested.
Patch #6 The 6185 is a member of the 6131 family. Add it to the probe
code of the 6131 driver.
Patch #7 and Patch #8 Simply the mutex's in mv88e6xxx.c. The SMI bus
is the bottleneck, not the granularity of the mutex's so simply the
code down to a single mutex.
Patch #8 Fixes a false positive lockdep splat, due to nested uses of
MDIO busses.
Patch #9 Fixes another false positive lockdep splat with the transmit
queue because of stacked Ethernet devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 5 May 2015 23:09:56 +0000 (01:09 +0200)]
net: dsa: Add lockdep class to tx queues to avoid lockdep splat
DSA stacks an Ethernet device on top of an Ethernet device. This can
cause false positive lockdep splats for the transmit queue: Acked-by: Florian Fainelli <f.fainelli@gmail.com>
=============================================
[ INFO: possible recursive locking detected ] 4.0.0-rc7-01838-g70621a215fc7 #386 Not tainted
---------------------------------------------
kworker/0:0/4 is trying to acquire lock:
(_xmit_ETHER#2){+.-...}, at: [<c040e95c>] sch_direct_xmit+0xa8/0x1fc
but task is already holding lock:
(_xmit_ETHER#2){+.-...}, at: [<c03f4208>] __dev_queue_xmit+0x4d4/0x56c
other info that might help us debug this:
Possible unsafe locking scenario:
DSA can have nested MDIO busses, where the Ethernet MDIO bus is used
to access an MDIO bus within the switch which has the PHYs connected
to it. This nesting causes lockdep to give false positives. Use
mutex_lock_nested() to avoid this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 5 May 2015 23:09:54 +0000 (01:09 +0200)]
net: dsa: mv88e6xxx: Replace stats mutex with SMI mutex
The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the stats mutex by the SMI mutex to make
the locking concept simpler.
The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 5 May 2015 23:09:53 +0000 (01:09 +0200)]
net: dsa: mv88e6xxx: Replace PHY mutex by SMI mutex
The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the PHY mutex by the SMI mutex to make
the locking concept simpler.
The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 5 May 2015 23:09:50 +0000 (01:09 +0200)]
net: dsa: Move mv88e6172 support into mv88e6352 family driver
The mv88e6172 is part of the mv88e6352 family of devices. Move support
for it out of the mv88e6171 driver into the mv88e6352, which results
in some simplifications to the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 5 May 2015 23:09:47 +0000 (01:09 +0200)]
net: dsa: Centralise global and port setup code into mv88e6xxx.
The port setup code in the individual drivers is identical for 6123,
6171, and 6352, and very similar in 6131. Move it all into mv88e6xxx,
using the chip families to differentiate on features.
Similarly, the global setup is also very similar. Move the majority
into mv8e6xxx.
The chips themselves fall into families. Add helpers which uses the
device IDs to determine if a device is a member of a family or not.
Add some additional device IDs to the existing list, to make these
helper functions more complete. However these IDs are not yet added to
the probe functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Arik Nemtsov [Wed, 6 May 2015 13:28:31 +0000 (16:28 +0300)]
cfg80211: change GO_CONCURRENT to IR_CONCURRENT for STA
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: Allow GO concurrent relaxation after BSS disconnection
If a P2P GO was allowed on a channel because of the GO concurrent
relaxation, i.e., another station interface was associated to an AP on
the same channel or the same UNII band, and the station interface
disconnected from the AP, allow the following use cases unless the
channel is marked as indoor only and the device is not operating in an
indoor environment:
1. Allow the P2P GO to stay on its current channel. The rationale behind
this is that if the channel or UNII band were allowed by the AP they
could still be used to continue the P2P GO operation, and avoid connection
breakage.
2. Allow another P2P GO to start on the same channel or another channel
that is in the same UNII band as the previous instantiated P2P GO.
Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 5 May 2015 14:32:29 +0000 (16:32 +0200)]
mac80211: validate cipher scheme PN length better
Currently, a cipher scheme can advertise an arbitrarily long
sequence counter, but mac80211 only supports up to 16 bytes
and the initial value from userspace will be truncated.
Fix two things:
* don't allow the driver to register anything longer than
the 16 bytes that mac80211 reserves space for
* require userspace to specify a starting value with the
correct length (or none at all)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 20 Apr 2015 16:21:58 +0000 (18:21 +0200)]
mac80211: extend get_key() to return PN for all ciphers
For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 20 Apr 2015 16:12:41 +0000 (18:12 +0200)]
mac80211: extend get_tkip_seq to all keys
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andreas Gröger [Tue, 5 May 2015 18:08:34 +0000 (20:08 +0200)]
can: janz-ican3: add support for CAL/CANopen firmware
In our department we are using some older Janz ICAN3-modules in our dekstop
pcs. There we have slightly different carrier boards than the janz-cmodio
supported in the kernel sources, called CAN-PCI2 with two submodules. But the
pci configuration regions are identical. So extending the supported pci devices
to the corresponding device ids is sufficient to get the drivers working.
* The old ICAN3-modules with firmware 1.28 need more then 250ms for the restart
after reset. I've increased the timeout to 500ms.
* The janz_ican3 module uses the raw can services of the Janz-firmware, this
means firmware must be ICANOS/2. Our ICAN3-modules are equipped with
CAL/CANopen-firmware, so I must use the appropriate commands for the layer
management services.
Te driver detects the firmware after module reset and selects the commands
matching the firmware. This affects the bus on/off-command
(ican3_set_bus_state) and the configuration of the bittiming
(ican3_set_bittiming). For better diagnostics the detected firmware string is
presented as sysfs attribute (fwinfo).
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Shawn Landden [Tue, 5 May 2015 16:07:16 +0000 (09:07 -0700)]
can.h: make padding given by gcc explicit
The current definition of struct can_frame has a 16-byte size, with 8-byte
alignment, but the 3 bytes of padding are not explicit like the similar 2 bytes
of padding of struct canfd_frame. Make it explicit so it is easier to read.
Signed-off-by: Shawn Landden <shawn@churchofgit.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
net: axienet: Removed _of_ prefix in probe and remove functions
Synchronize names with other drivers.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: axienet: Removed coding style errors and warnings
Removed checkpatch.pl errors and warnings.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper checks to handle the PHY-less case.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: axienet: Handle jumbo frames for lesser frame sizes
In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The packet completion interrupts for TX and RX should be serviced before
the packets are consumed. This ensures against the degenerate case when a
new completion interrupt is raised after the handler has exited but before
the interrupts are cleared. In this case its possible for the ISR to clear
an unhandled interrupt (leading to potential deadlock).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Tested-by: Jason Wu <huanyu@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The AXI-DMA rx-delay interrupt can sometimes be triggered
when there are 0 outstanding packets received. This is due
to the fact that the receive function will greedily consume
as many packets as possible on interrupt. So if two packets
(with a very particular timing) arrive in succession they
will each cause the rx-delay interrupt, but the first interrupt
will consume both packets.
This means the second interrupt is a 0 packet receive.
This is mostly OK, except that the tail pointer register is
updated unconditionally on receive. Currently the tail pointer
is always set to the current bd-ring descriptor under
the assumption that the hardware has moved onto the next
descriptor. What this means for length 0 recv is the current
descriptor that the hardware is potentially yet to use will
be marked as the tail. This causes the hardware to think
its run out of descriptors deadlocking the whole rx path.
Fixed by updating the tail pointer to the most recent
successfully consumed descriptor.
Reported-by: Wendy Liang <wendy.liang@xilinx.com> Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Tested-by: Jason Wu <huanyu@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RGMII. The h/w configuration
parameter C_PHY_TYPE, which represents the interface configured in
the design, is used to differentiate various interfaces supported
by AXI Ethernet.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 May 2015 23:31:50 +0000 (19:31 -0400)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
Trivial fixes and changes for SGE
This patch series adds the following.
Discard packet if length is greater than MTU, move sge monitor code to a
new routine, add device node to ULD info, add congestion notification from
SGE for ingress queue and freelists and for T5, setting up the Congestion
Manager values of the new RX Ethernet Queue is done by firmware now.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
Thanks
V2: Align parenthesis for PATCH 2/6 and PATCH 5/6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Discard the packet if the length is greater than mtu
pktgen sends raw udp packets and bypasses most of the
linux networking stack. User can specify different packet sizes.
Hence we need to discard the packet if the length is greater than mtu
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Pass in a Congestion Channel Map to t4_sge_alloc_rxq()
Passes a Congestion Channel Map to t4_sge_alloc_rxq()
for the Ethernet RX Queues based on the MPS Buffer Group Map
of the TX Channel rather than just the TX Channel Map.
Also, in t4_sge_alloc_rxq() for T5, setting up the
Congestion Manager values of the new RX Ethernet Queue is
done by firmware now.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Make sure that Freelist size is larger than Egress Congestion Threshold
We need to make sure that the Free List Size, in pointers, is at
least 2 Egress Queue Units (8 pointers/each) larger than the SGE's Egress
Congestion Threshold (in pointers).
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Tue, 5 May 2015 00:27:02 +0000 (02:27 +0200)]
rhashtable-test: Fix 64bit division
A 64bit division went in unnoticed. Use do_div() to accomodate
non 64bit architectures.
Reported-by: kbuild test robot Fixes: 1aa661f5c3df ("rhashtable-test: Measure time to insert, remove & traverse entries") Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 May 2015 23:29:50 +0000 (19:29 -0400)]
Merge branch 'ipvlan-mcast'
Mahesh Bandewar says:
====================
Multicast processing in IPvlan
Dan Willems pointed out that autoconf in IPvlan is broken because of the
way broadcast bit gets set. Since broadcast processing is a real performance
drain, the broadcast bit in multicast filter was only set when the interface
was configured with IPv4 address. In autoconf scenario, when there are
no addresses configured; this logic did not work and it wouldn't allow
DHCPv4 to work. The only way was to add protocol specific hacks to avoid
processing unnecessary broadcast burdon.
This jugglery could be avoided if these multicast / broadcast packets are taken
out of fast-path and are processed in a work-queue. This will enable us to add
broadcast bit in all multicast filters without any impact on performance of
the virtual device. This patch series just does that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Tue, 5 May 2015 00:06:11 +0000 (17:06 -0700)]
ipvlan: Always set broadcast bit in multicast filter
Earlier tricks of setting broadcast bit only when IPv4 address is added
onto interface are not good enough especially when autoconf comes in play.
Setting them on always is performance drag but now that multicast /
broadcast is not processed in fast-path; enabling broadcast will let
autoconf work correctly without affecting performance characteristics of
the device.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Tue, 5 May 2015 00:06:03 +0000 (17:06 -0700)]
ipvlan: Defer multicast / broadcast processing to a work-queue
Processing multicast / broadcast in fast path is performance draining
and having more links means more cloning and bringing performance
down further.
Broadcast; in particular, need to be given to all the virtual links.
Earlier tricks of enabling broadcast bit for IPv4 only interfaces are not
really working since it fails autoconf. Which means enabling broadcast
for all the links if protocol specific hacks do not have to be added into
the driver.
This patch defers all (incoming as well as outgoing) multicast traffic to
a work-queue leaving only the unicast traffic in the fast-path. Now if we
need to apply any additional tricks to further reduce the impact of this
(multicast / broadcast) type of traffic, it can be implemented while
processing this work without affecting the fast-path.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 May 2015 23:24:43 +0000 (19:24 -0400)]
Merge branch 'eth_proto_is_802_3'
Alexander Duyck says:
====================
Add eth_proto_is_802_3 to provide improved means of checking Ethertype
This patch series implements and makes use of eth_proto_is_802_3(). The
idea behind the function is to provide an optimized means of testing to
determine if a given Ethertype value is a length or 802.3 protocol number.
The standard path for this was to use ntohs(proto) and then perform a
comparison. This adds a slight cost as it usually requires either a 16b
rotate or byte swap which can cost 1 cycle or more depending on the
processor.
I had previously addressed this for eth_type_trans, however in doing so I had
overlooked checking with sparse and had introduced a couple sparse warnings.
The first patch in this series fixes those sparse warnings as well as does
some additional optimization for big endian systems. In addition it pushes
the code out into a separate function which can then be used in the other
patches to reduce the instruction count/processing time in those functions
as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 4 May 2015 21:33:48 +0000 (14:33 -0700)]
etherdev: Fix sparse error, make test usable by other functions
This change does two things. First it fixes a sparse error for the fact
that the __be16 degrades to an integer. Since that is actually what I am
kind of doing I am simply working around that by forcing both sides of the
comparison to u16.
Also I realized on some compilers I was generating another instruction for
big endian systems such as PowerPC since it was masking the value before
doing the comparison. So to resolve that I have simply pulled the mask out
and wrapped it in an #ifndef __BIG_ENDIAN.
Lastly I pulled this all out into its own function. I notices there are
similar checks in a number of other places so this function can be reused
there to help reduce overhead in these paths as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bernhard Thaler [Mon, 4 May 2015 20:47:13 +0000 (22:47 +0200)]
bridge: change BR_GROUPFWD_RESTRICTED to allow forwarding of LLDP frames
BR_GROUPFWD_RESTRICTED bitmask restricts users from setting values to
/sys/class/net/brX/bridge/group_fwd_mask that allow forwarding of
some IEEE 802.1D Table 7-10 Reserved addresses:
Change BR_GROUPFWD_RESTRICTED to allow to forward LLDP frames and document
group_fwd_mask.
e.g.
echo 16384 > /sys/class/net/brX/bridge/group_fwd_mask
allows to forward LLDP frames.
This may be needed for bridge setups used for network troubleshooting or
any other scenario where forwarding of LLDP frames is desired (e.g. bridge
connecting a virtual machine to real switch transmitting LLDP frames that
virtual machine needs to receive).
Tested on a simple bridge setup with two interfaces and host transmitting
LLDP frames on one side of this bridge (used lldpd). Setting group_fwd_mask
as described above lets LLDP frames traverse bridge.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 4 May 2015 04:34:46 +0000 (21:34 -0700)]
tcp: provide SYN headers for passive connections
This patch allows a server application to get the TCP SYN headers for
its passive connections. This is useful if the server is doing
fingerprinting of clients based on SYN packet contents.
Two socket options are added: TCP_SAVE_SYN and TCP_SAVED_SYN.
The first is used on a socket to enable saving the SYN headers
for child connections. This can be set before or after the listen()
call.
The latter is used to retrieve the SYN headers for passive connections,
if the parent listener has enabled TCP_SAVE_SYN.
TCP_SAVED_SYN is read once, it frees the saved SYN headers.
The data returned in TCP_SAVED_SYN are network (IPv4/IPv6) and TCP
headers.
Original patch was written by Tom Herbert, I changed it to not hold
a full skb (and associated dst and conntracking reference).
We have used such patch for about 3 years at Google.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 23 Apr 2015 10:19:22 +0000 (12:19 +0200)]
mac80211: make LED triggering depend on activation
When LED triggers are compiled in, but not used, mac80211 will still
call them to update the status. This isn't really a problem for the
assoc and radio ones, but the TX/RX (and to a certain extend TPT)
ones can be called very frequently (for every packet.)
In order to avoid that when they're not used, track their activation
and call the corresponding trigger (and in the TPT case, account for
throughput) only when the trigger is actually used by an LED.
Additionally, make those trigger functions inlines since theyre only
used once in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 22 Apr 2015 19:07:39 +0000 (21:07 +0200)]
mac80211: clean up station debugfs
Remove items that can be retrieved through nl80211. This also
removes two items (tx_packets and tx_bytes) where only the VO
counter was exposed since they are split up per AC but in the
debugfs file only the first AC was shown.
Also remove the useless "dev" file - the stations have long
been in a sub-directory of the netdev so there's no need for
that any more.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 22 Apr 2015 18:55:55 +0000 (20:55 +0200)]
mac80211: remove sta->tx_fragments counter
This counter is unsafe with concurrent TX and is only exposed
through debugfs and ethtool. Instead of trying to fix it just
remove it for now, if it's really needed then it should be
exposed through nl80211 and in a way that drivers that do the
fragmentation in the device could support it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 22 Apr 2015 18:47:28 +0000 (20:47 +0200)]
mac80211: move dot11 counters under MAC80211_DEBUG_COUNTERS
Since these counters can only be read through debugfs, there's
very little point in maintaining them all the time. However,
even just making them depend on debugfs is pointless - they're
not normally used. Additionally a number of them aren't even
concurrency safe.
Move them under MAC80211_DEBUG_COUNTERS so they're normally
not even compiled in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 22 Apr 2015 18:25:20 +0000 (20:25 +0200)]
mac80211: clean up global debugfs statistics
The debugfs statistics macros are pointlessly verbose, so change
that macro to just have a single argument. While at it, remove
the unused counters and rename rx_expand_skb_head2 to the better
rx_expand_skb_head_defrag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Lüssing [Mon, 4 May 2015 22:19:35 +0000 (00:19 +0200)]
net: fix two sparse warnings introduced by IGMP/MLD parsing exports
> net/core/skbuff.c:4108:13: sparse: incorrect type in assignment (different base types)
> net/ipv6/mcast_snoop.c:63 ipv6_mc_check_exthdrs() warn: unsigned 'offset' is never less than zero.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2015 19:37:08 +0000 (15:37 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-05-04
This series contains updates to igb, e100, e1000e and ixgbe.
Todd cleans up igb_enable_mas() since it should only be called for the
82575 silicon and has no clear return, so modify the function to void.
Jean Sacren found upon inspection that 'err' did not need to be
initialized, since it is immediately overwritten.
Alex Duyck provides two patches for e1000e, the first cleans up the
handling VLAN_HLEN as a part of max frame size. Fixes the issue: c751a3d58cf2d ("e1000e: Correctly include VLAN_HLEN when changing
interface MTU"). The second fixes an issue where the driver was not
allowing jumbo frames to be enabled when CRC stripping was disabled,
however it was allowing CRC stripping to be disabled while jumbo frames
were enabled.
Jeff (me) fixes a warning found on PPC where the use of do_div() needed
to use u64 arg and not s64.
Mark provides three ixgbe patches, first to fix the Intel On-chip System
Fabric (IOSF) Sideband message interfaces, to serialize access using both
PHY bits in the SWFW_SEMAPHORE register. Then fixes how semaphore bits
were released, since they should be released in reverse of the order that
they were taken. Lastly updates ixgbe to use a signed type to hold
error codes, since error codes are negative, so consistently use signed
types when handling them.
v2: dropped the previous #6-#8 patches by Hiroshi Shimanoto based on
feedback from Or Gerlitz (and David Miller) that it appears there
needs to be further discussion on how this gets implemented.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2015 19:04:02 +0000 (15:04 -0400)]
Merge branch 'tipc-topology-cleanup'
Ying Xue says:
====================
tipc: cleanup topology server
Not only function names declared in subscr.c are very confused, but
also topology server's locking policy is not designed very well, for
instance, usually leading to panic in some special corner cases.
In this series, we attempt to eliminate the confusion of function names
and simplify topology server's locking policy to solve above mentioned
issues. More importantly, the change will make relevant code easily
understandable and maintainable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Mon, 4 May 2015 02:36:47 +0000 (10:36 +0800)]
tipc: adjust locking policy of subscription
Currently subscriber's lock protects not only subscriber's subscription
list but also all subscriptions linked into the list. However, as all
members of subscription are never changed after they are initialized,
it's unnecessary for subscription to be protected under subscriber's
lock. If the lock is used to only protect subscriber's subscription
list, the adjustment not only makes the locking policy simpler, but
also helps to avoid a deadlock which may happen once creating a
subscription is failed.
Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Jon Maloy <jon.maloy@ericson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Mon, 4 May 2015 02:36:46 +0000 (10:36 +0800)]
tipc: involve reference counter for subscriber
At present subscriber's lock is used to protect the subscription list
of subscriber as well as subscriptions linked into the list. While one
or all subscriptions are deleted through iterating the list, the
subscriber's lock must be held. Meanwhile, as deletion of subscription
may happen in subscription timer's handler, the lock must be grabbed
in the function as well. When subscription's timer is terminated with
del_timer_sync() during above iteration, subscriber's lock has to be
temporarily released, otherwise, deadlock may occur. However, the
temporary release may cause the double free of a subscription as the
subscription is not disconnected from the subscription list.
Now if a reference counter is introduced to subscriber, subscription's
timer can be asynchronously stopped with del_timer(). As a result, the
issue is not only able to be fixed, but also relevant code is pretty
readable and understandable.
Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Jon Maloy <jon.maloy@ericson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Mon, 4 May 2015 02:36:44 +0000 (10:36 +0800)]
tipc: rename functions defined in subscr.c
When a topology server accepts a connection request from its client,
it allocates a connection instance and a tipc_subscriber structure
object. The former is used to communicate with client, and the latter
is often treated as a subscriber which manages all subscription events
requested from a same client. When a topology server receives a request
of subscribing name services from a client through the connection, it
creates a tipc_subscription structure instance which is seen as a
subscription recording what name services are subscribed. In order to
manage all subscriptions from a same client, topology server links
them into the subscrp_list of the subscriber. So subscriber and
subscription completely represents different meanings respectively,
but function names associated with them make us so confused that we
are unable to easily tell which function is against subscriber and
which is to subscription. So we want to eliminate the confusion by
renaming them.
Signed-off-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Jon Maloy <jon.maloy@ericson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2015 18:49:23 +0000 (14:49 -0400)]
Merge branch 'igmp_mld_export'
Linus Lüssing says:
====================
Exporting IGMP/MLD checking from bridge code
The multicast optimizations in batman-adv are yet only usable and
enabled in non-bridged scenarios. To be able to support bridged setups
batman-adv needs to be able to detect IGMP/MLD queriers and reports on
mesh nodes without bridges, too. See the following link for details:
To avoid duplicate code between the bridge and batman-adv, the IGMP/MLD
message validation code is moved from the bridge to the IPv4/IPv6 stack.
On the way, some refactoring to increase readability and to iron out
some subtle differences between the IGMP and MLD parsing code is done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log