NeilBrown [Fri, 18 Nov 2016 02:22:04 +0000 (13:22 +1100)]
md: add block tracing for bio_remapping
The block tracing infrastructure (accessed with blktrace/blkparse)
supports the tracing of mapping bios from one device to another.
This is currently used when a bio in a partition is mapped to the
whole device, when bios are mapped by dm, and for mapping in md/raid5.
Other md personalities do not include this tracing yet, so add it.
When a read-error is detected we redirect the request to a different device.
This could justifiably be seen as a new mapping for the originial bio,
or a secondary mapping for the bio that errors. This patch uses
the second option.
When md is used under dm-raid, the mappings are not traced as we do
not have access to the block device number of the parent.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
NeilBrown [Tue, 8 Nov 2016 23:21:32 +0000 (10:21 +1100)]
md: remove md_super_wait() call after bitmap_flush()
bitmap_flush() finishes with bitmap_update_sb(), and that finishes
with write_page(..., 1), so write_page() will wait for all writes
to complete. So there is no point calling md_super_wait()
immediately afterwards.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
NeilBrown [Tue, 8 Nov 2016 23:21:32 +0000 (10:21 +1100)]
md/raid1: fix: IO can block resync indefinitely
While performing a resync/recovery, raid1 divides the
array space into three regions:
- before the resync
- at or shortly after the resync point
- much further ahead of the resync point.
Write requests to the first or third do not need to wait. Write
requests to the middle region do need to wait if resync requests are
pending.
If there are any active write requests in the middle region, resync
will wait for them.
Due to an accounting error, there is a small range of addresses,
between conf->next_resync and conf->start_next_window, where write
requests will *not* be blocked, but *will* be counted in the middle
region. This can effectively block resync indefinitely if filesystem
writes happen repeatedly to this region.
As ->next_window_requests is incremented when the sector is after
conf->start_next_window + NEXT_NORMALIO_DISTANCE
the same boundary should be used for determining when write requests
should wait.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
NeilBrown [Fri, 4 Nov 2016 05:46:03 +0000 (16:46 +1100)]
md/bitmap: Don't write bitmap while earlier writes might be in-flight
As we don't wait for writes to complete in bitmap_daemon_work, they
could still be in-flight when bitmap_unplug writes again. Or when
bitmap_daemon_work tries to write again.
This can be confusing and could risk the wrong data being written last.
So make sure we wait for old writes to complete before new writes start.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
NeilBrown [Fri, 4 Nov 2016 05:46:03 +0000 (16:46 +1100)]
md/raid10: abort delayed writes when device fails.
When writing to an array with a bitmap enabled, the writes are grouped
in batches which are preceded by an update to the bitmap.
It is quite likely if that a drive develops a problem which is not
media related, that the bitmap write will be the first to report an
error and cause the device to be marked faulty (as the bitmap write is
at the start of a batch).
In this case, there is point submiting the subsequent writes to the
failed device - that just wastes times.
So re-check the Faulty state of a device before submitting a
delayed write.
This requires that we keep the 'rdev', rather than the 'bdev' in the
bio, then swap in the bdev just before final submission.
Reported-by: Hannes Reinecke <hare@suse.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
NeilBrown [Fri, 4 Nov 2016 05:46:03 +0000 (16:46 +1100)]
md/raid1: abort delayed writes when device fails.
When writing to an array with a bitmap enabled, the writes are grouped
in batches which are preceded by an update to the bitmap.
It is quite likely if that a drive develops a problem which is not
media related, that the bitmap write will be the first to report an
error and cause the device to be marked faulty (as the bitmap write is
at the start of a batch).
In this case, there is point submiting the subsequent writes to the
failed device - that just wastes times.
So re-check the Faulty state of a device before submitting a
delayed write.
This requires that we keep the 'rdev', rather than the 'bdev' in the
bio, then swap in the bdev just before final submission.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
NeilBrown [Fri, 4 Nov 2016 05:46:03 +0000 (16:46 +1100)]
md: perform async updates for metadata where possible.
When adding devices to, or removing device from, an array we need to
update the metadata. However we don't need to do it synchronously as
data integrity doesn't depend on these changes being recorded
instantly. So avoid the synchronous call to md_update_sb and just set
a flag so that the thread will do it.
This can reduce the number of updates performed when lots of devices
are being added or removed.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
NeilBrown [Wed, 2 Nov 2016 03:16:49 +0000 (14:16 +1100)]
md: change all printk() to pr_err() or pr_warn() etc.
1/ using pr_debug() for a number of messages reduces the noise of
md, but still allows them to be enabled when needed.
2/ try to be consistent in the usage of pr_err() and pr_warn(), and
document the intention
3/ When strings have been split onto multiple lines, rejoin into
a single string.
The cost of having lines > 80 chars is less than the cost of not
being able to easily search for a particular message.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
Revert commit 11367799f3d1 ("md: Prevent IO hold during accessing to faulty
raid5 array") as it doesn't comply with commit c3cce6cda162 ("md/raid5:
ensure device failure recorded before write request returns."). That change
is not required anymore as the problem is resolved by commit 16f889499a52
("md: report 'write_pending' state when array in sync") - read request is
stuck as array state is not reported correctly via sysfs attribute.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
Tomasz Majchrzak [Tue, 25 Oct 2016 15:07:08 +0000 (17:07 +0200)]
md: wake up personality thread after array state update
When raid1/raid10 array fails to write to one of the drives, the request
is added to bio_end_io_list and finished by personality thread. The
thread doesn't handle it as long as MD_CHANGE_PENDING flag is set. In
case of external metadata this flag is cleared, however the thread is
not woken up. It causes request to be blocked for few seconds (until
another action on the array wakes up the thread) or to get stuck
indefinitely.
Wake up personality thread once MD_CHANGE_PENDING has been cleared.
Moving 'restart_array' call after the flag is cleared it not a solution
because in read-write mode the call doesn't wake up the thread.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
Tomasz Majchrzak [Fri, 21 Oct 2016 14:27:08 +0000 (16:27 +0200)]
md: don't fail an array if there are unacknowledged bad blocks
If external metadata handler supports bad blocks and unacknowledged bad
blocks are present, don't report disk via sysfs as faulty. Such
situation can be still handled so disk just has to be blocked for a
moment. It makes it consistent with kernel state as corresponding rdev
flag is also not set.
When the disk in being unblocked there are few cases:
1. Disk has been in blocked and faulty state, it is being unblocked but
it still remains in faulty state. Metadata handler will remove it from
array in the next call.
2. There is no bad block support in external metadata handler and bad
blocks are present - put the disk in blocked and faulty state (see
case 1).
3. There is bad block support in external metadata handler and all bad
blocks are acknowledged - clear all flags, continue.
4. There is bad block support in external metadata handler but there are
still unacknowledged bad blocks - clear all flags, continue. It is fine
to clear Blocked flag because it was probably not set anyway (if it was
it is case 1). BlockedBadBlocks flag can also be cleared because the
request waiting for it will set it again when it finds out that some bad
block is still not acknowledged. Recovery is not necessary but there are
no problems if the flag is set. Sysfs rdev state is still reported as
blocked (due to unacknowledged bad blocks) so metadata handler will
process remaining bad blocks and unblock disk again.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
Tomasz Majchrzak [Fri, 21 Oct 2016 14:26:57 +0000 (16:26 +0200)]
md: add bad block support for external metadata
Add new rdev flag which external metadata handler can use to switch
on/off bad block support. If new bad block is encountered, notify it via
rdev 'unacknowledged_bad_blocks' sysfs file. If bad block has been
cleared, notify update to rdev 'bad_blocks' sysfs file.
When bad blocks support is being removed, just clear rdev flag. It is
not necessary to reset badblocks->shift field. If there are bad blocks
cleared or added at the same time, it is ok for those changes to be
applied to the structure. The array is in blocked state and the drive
which cannot handle bad blocks any more will be removed from the array
before it is unlocked.
Simplify state_show function by adding a separator at the end of each
string and overwrite last separator with new line.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Reviewed-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: Shaohua Li <shli@fb.com>
Linus Torvalds [Mon, 7 Nov 2016 18:16:23 +0000 (10:16 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"It's been pretty quiet on the fixes side of things for us, but Artem
reported a build failure introduced during the merge window that
appears with older GCCs that do not support asm goto. The fix is
bigger than I'd like, but it's a mechnical move of some constants to
break an include dependency between atomic.h and jump_label.h when
!HAVE_JUMP_LABEL.
Summary:
- Fix build failure on compilers without asm goto"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix circular include of asm/lse.h through linux/jump_label.h
Linus Torvalds [Mon, 7 Nov 2016 18:14:47 +0000 (10:14 -0800)]
Merge tag 'openrisc-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull openrisc fix from Guenter Roeck:
"Fix openrisc crash caused by ro_init changes"
* tag 'openrisc-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
openrisc: Define __ro_after_init to avoid crash
Linus Torvalds [Mon, 7 Nov 2016 18:13:10 +0000 (10:13 -0800)]
Merge tag 'hwmon-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix resource leak on devm_kcalloc failure"
* tag 'hwmon-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (core) fix resource leak on devm_kcalloc failure
Linus Torvalds [Mon, 7 Nov 2016 18:05:39 +0000 (10:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- modprobe-after-rmmod load failure bugfix for intel-ish, from Even Xu
- IRQ probing bugfix for intel-ish, from Srinivas Pandruvada
- attribute parsing fix in hid-sensor, from Ooi, Joyce
- other small misc fixes / quirky device additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: sensor: fix attributes in HID sensor interface
HID: intel-ish-hid: request_irq failure
HID: intel-ish-hid: Fix driver reinit failure
HID: intel-ish-hid: Move DMA disable code to new function
HID: intel-ish-hid: consolidate ish wake up operation
HID: usbhid: add ATEN CS962 to list of quirky devices
HID: intel-ish-hid: Fix !CONFIG_PM build warning
HID: sensor-hub: Fix packing of result buffer for feature report
Bisect points to commit d2ec3f77de8e ("pty: make ptmx file ops read-only
after init"). Fix by defining __ro_after_init for the openrisc
architecture, similar to parisc.
Catalin Marinas [Thu, 3 Nov 2016 18:34:34 +0000 (18:34 +0000)]
arm64: Fix circular include of asm/lse.h through linux/jump_label.h
Commit efd9e03facd0 ("arm64: Use static keys for CPU features")
introduced support for static keys in asm/cpufeature.h, including
linux/jump_label.h. When CC_HAVE_ASM_GOTO is not defined, this causes a
circular dependency via linux/atomic.h, asm/lse.h and asm/cpufeature.h.
This patch moves the capability macros out out of asm/cpufeature.h into
a separate asm/cpucaps.h and modifies some of the #includes accordingly.
Fixes: efd9e03facd0 ("arm64: Use static keys for CPU features") Reported-by: Artem Savkov <asavkov@redhat.com> Tested-by: Artem Savkov <asavkov@redhat.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Linus Torvalds [Sat, 5 Nov 2016 18:46:02 +0000 (11:46 -0700)]
Merge branches 'sched-urgent-for-linus' and 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull stack vmap fixups from Thomas Gleixner:
"Two small patches related to sched_show_task():
- make sure to hold a reference on the task stack while accessing it
- remove the thread_saved_pc printout
.. and add a sanity check into release_task_stack() to catch problems
with task stack references"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Remove pointless printout in sched_show_task()
sched/core: Fix oops in sched_show_task()
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fork: Add task stack refcounting sanity check and prevent premature task stack freeing
Linus Torvalds [Sat, 5 Nov 2016 18:34:07 +0000 (11:34 -0700)]
Merge tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"There are several bug fixes queued:
- fix raid5-cache recovery bugs
- fix discard IO error handling for raid1/10
- fix array sync writes bogus position to superblock
- fix IO error handling for raid array with external metadata"
* tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: be careful not lot leak internal curr_resync value into metadata. -- (all)
raid1: handle read error also in readonly mode
raid5-cache: correct condition for empty metadata write
md: report 'write_pending' state when array in sync
md/raid5: write an empty meta-block when creating log super-block
md/raid5: initialize next_checkpoint field before use
RAID10: ignore discard error
RAID1: ignore discard error
Linus Torvalds [Sat, 5 Nov 2016 18:28:21 +0000 (11:28 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two more important data integrity fixes related to RAID device drivers
which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
path and a memory leak in the scsi_debug driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices
Linus Torvalds [Sat, 5 Nov 2016 18:15:09 +0000 (11:15 -0700)]
Merge tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of fixup patches meant to fix the usage of DMA on stack, plus
one warning fixup"
* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
[media] radio-bcm2048: don't ignore errors
[media] pctv452e: fix semicolon.cocci warnings
[media] flexcop-usb: don't use stack for DMA
[media] stk-webcam: don't use stack for DMA
[media] s2255drv: don't use stack for DMA
[media] cpia2_usb: don't use stack for DMA
[media] digitv: handle error code on RC query
[media] dw2102: return error if su3000_power_ctrl() fails
[media] nova-t-usb2: handle error code on RC query
[media] technisat-usb2: use DMA buffers for I2C transfers
[media] pctv452e: don't call BUG_ON() on non-fatal error
[media] pctv452e: don't do DMA on stack
[media] nova-t-usb2: don't do DMA on stack
[media] gp8psk: don't go past the buffer size
[media] gp8psk: don't do DMA on stack
[media] dtv5100: don't do DMA on stack
[media] dtt200u: handle USB control message errors
[media] dtt200u: don't do DMA on stack
[media] dtt200u-fe: handle errors on USB control messages
[media] dtt200u-fe: don't do DMA on stack
...
Linus Torvalds [Sat, 5 Nov 2016 18:11:31 +0000 (11:11 -0700)]
Merge tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix for a Qualcomm driver issue that causes a use-before-set crash
- fix for DesignWare iATU unroll support that causes external aborts
when enabling the host bridge
* tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
Linus Torvalds [Sat, 5 Nov 2016 17:52:29 +0000 (10:52 -0700)]
Merge tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates to reflect some new maintainers/submaintainers.
We have some great volunteers who've been developing and reviewing
already. We're going to try a group maintainership model, so
eventually you'll probably see pull requests from people besides me.
- NAND fixes from Boris:
"Three simple fixes:
- fix a non-critical bug in the gpmi driver
- fix a bug in the 'automatic NAND timings selection' feature
introduced in 4.9-rc1
- fix a false positive uninitialized-var warning"
* tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd:
mtd: mtk: avoid warning in mtk_ecc_encode
mtd: nand: Fix data interface configuration logic
mtd: nand: gpmi: disable the clocks on errors
MAINTAINERS: add more people to the MTD maintainer team
MAINTAINERS: add a maintainer for the SPI NOR subsystem
Linus Torvalds [Sat, 5 Nov 2016 17:42:20 +0000 (10:42 -0700)]
Merge tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.9 series:
- Fix a nasty file descriptor leak when getting line handles.
- A fix for a cleanup that seemed innocent but created a problem for
drivers instantiating several gpiochips for one single OF node.
- Fix a unpredictable problem using irq_domain_simple() in the mvebu
driver by converting it to a lineas irqdomain"
* tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/mvebu: Use irq_domain_add_linear
gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak
Ooi, Joyce [Thu, 3 Nov 2016 10:55:15 +0000 (18:55 +0800)]
HID: sensor: fix attributes in HID sensor interface
User is unable to access to input-X-yyy and feature-X-yyy where
X is a hex value and more than 9 (e.g. input-a-yyy, feature-b-yyy) in HID
sensor custom sysfs interface.
This is because when creating the attribute, the attribute index is
written to using %x (hex). However, when reading and writing values into
the attribute, the attribute index is scanned using %d (decimal). Hence,
user is unable to access to attributes with index in hex values
(e.g. 'a', 'b', 'c') but able to access to attributes with index in
decimal values (e.g. 1, 2, 3,..).
This fix will change input-%d-%x-%s and feature-%d-%x-%s to input-%x-%x-%s
and feature-%x-%x-%s in show_values() and store_values() accordingly.
On some platforms ISH interrupt is shared, which causes request_irq to
fail. This requires IRQF_SHARED irq flag.
But IRQF_NO_SUSPEND and IRQF_SHARED should not be used together, so
removed IRQF_NO_SUSPEND flag. Anyway this driver doesn't require
IRQF_NO_SUSPEND, as this interrupt is not required during "noirq" phases
of suspending and resuming devices as well as during the time when
nonboot CPUs are taken offline and brought back online.
Even Xu [Fri, 21 Oct 2016 22:48:38 +0000 (15:48 -0700)]
HID: intel-ish-hid: consolidate ish wake up operation
Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Linus Torvalds [Sat, 5 Nov 2016 03:12:10 +0000 (20:12 -0700)]
Merge tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Fixes for some recent regressions including fallout from the vmalloc'd
stack change (after which we can no longer encrypt stuff on the
stack)"
* tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix general protection fault in release_lock_stateid()
svcrdma: backchannel cannot share a page for send and rcv buffers
sunrpc: fix some missing rq_rbuffer assignments
sunrpc: don't pass on-stack memory to sg_set_buf
nfsd: move blocked lock handling under a dedicated spinlock
Linus Torvalds [Sat, 5 Nov 2016 03:08:16 +0000 (20:08 -0700)]
Merge branch 'for-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from Chris Mason:
"Some fixes that Dave Sterba collected. We held off on these last week
because I was focused on the memory corruption testing"
* 'for-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix WARNING in btrfs_select_ref_head()
Btrfs: remove some no-op casts
btrfs: pass correct args to btrfs_async_run_delayed_refs()
btrfs: make file clone aware of fatal signals
btrfs: qgroup: Prevent qgroup->reserved from going subzero
Btrfs: kill BUG_ON in do_relocation
Linus Torvalds [Sat, 5 Nov 2016 03:03:14 +0000 (20:03 -0700)]
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix two more POSIX ACL bugs introduced in 4.8 and add a missing fsync
during copy up to prevent possible data loss"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fsync after copy-up
ovl: fix get_acl() on tmpfs
ovl: update S_ISGID when setting posix ACLs
Linus Torvalds [Fri, 4 Nov 2016 20:30:13 +0000 (13:30 -0700)]
Merge tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for amdgpu, radeon, intel, imx and virtio-gpu.
This is a bit larger than I'd like, but I had some stuff I meant to
send for -rc3 but was waiting for the PAT regression fix to land. So
this is really fixes for rc3 and rc4 in one go.
There are a set of fixes for an oops we've been seeing around MST
display unplug, along with more suspend/resume and shutdown fixes for
amdgpu, one power management follow on fix for nouveau, and set of imx
fixes, and a single virtio-gpu regression fix"
* tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux: (54 commits)
virtio-gpu: fix vblank events
drm/nouveau/acpi: fix check for power resources support
drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
drm/i915: Remove two invalid warns
drm/i915: Rotated view does not need a fence
drm/i915/fbc: fix CFB size calculation for gen8+
drm: i915: Wait for fences on new fb, not old
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: fix watermarks when using the pipe scaler
drm/i915: Fix mismatched INIT power domain disabling during suspend
drm/i915: fix a read size argument
drm/i915: Use fence_write() from rpm resume
drm/i915/gen9: fix DDB partitioning for multi-screen cases
drm/i915: workaround sparse warning on variable length arrays
drm/i915: keep declarations in i915_drv.h
drm/amd/powerplay: fix bug get wrong evv voltage of Polaris.
drm/amdgpu/si_dpm: workaround for SI kickers
drm/radeon/si_dpm: workaround for SI kickers
drm/amdgpu: fix s3 resume back, uvd dpm randomly can't disable.
...
Niklas Cassel [Fri, 14 Oct 2016 21:54:55 +0000 (23:54 +0200)]
PCI: designware: Check for iATU unroll support after initializing host
dw_pcie_iatu_unroll_enabled() reads a dbi_base register. Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init. Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.
Fixes: a0601a470537 ("PCI: designware: Add iATU Unroll feature") Tested-by: James Le Cuirot <chewi@gentoo.org> Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Joao Pinto <jpinto@synopsys.com> Acked-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Fri, 4 Nov 2016 20:08:05 +0000 (13:08 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One NULL pointer dereference, and two fixes for regressions introduced
during the merge window.
The rest are fixes for MIPS, s390 and nested VMX"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: Check memopp before dereference (CVE-2016-8630)
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
KVM: x86: fix wbinvd_dirty_mask use-after-free
kvm/x86: Show WRMSR data is in hex
kvm: nVMX: Fix kernel panics induced by illegal INVEPT/INVVPID types
KVM: document lock orders
KVM: fix OOPS on flush_work
KVM: s390: Fix STHYI buffer alignment for diag224
KVM: MIPS: Precalculate MMIO load resume PC
KVM: MIPS: Make ERET handle ERL before EXL
KVM: MIPS: Fix lazy user ASID regenerate for SMP
Linus Torvalds [Fri, 4 Nov 2016 20:03:57 +0000 (13:03 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A set of MIPS fixes for 4.9:
- lots of fixes for printk continuations
- six fixes for FP related code.
- fix max_low_pfn with disabled highmem
- fix KASLR handling of NULL FDT and KASLR for generic kernels
- fix build of compressed image
- provide default mips_cpc_default_phys_base to ignore CPC
- fix reboot on Malta"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix max_low_pfn with disabled highmem
MIPS: Correct MIPS I FP sigcontext layout
MIPS: Fix ISA I/II FP signal context offsets
MIPS: Remove FIR from ISA I FP signal context
MIPS: Fix ISA I FP sigcontext access violation handling
MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue
MIPS: ptrace: Also initialize the FP context on individual FCSR writes
MIPS: dump_tlb: Fix printk continuations
MIPS: Fix __show_regs() output
MIPS: traps: Fix output of show_code
MIPS: traps: Fix output of show_stacktrace
MIPS: traps: Fix output of show_backtrace
MIPS: Fix build of compressed image
MIPS: generic: Fix KASLR for generic kernel.
MIPS: KASLR: Fix handling of NULL FDT
MIPS: Malta: Fixup reboot
MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC
Linus Torvalds [Fri, 4 Nov 2016 20:01:13 +0000 (13:01 -0700)]
Merge branch 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"The first three patches are trivial and add some required KERN_CONT,
ignore the new pkey syscalls on parisc and use the LINUX_GATEWAY_ADDR
define instead of hardcoded values.
The two patches from Dave Anglin are important.
The first one avoids trashing the sr2 and sr3 space registers in the
Light-weight syscall path. Especially the usage of sr3 is critical
since it may get trashed by the interrupt handler.
The second patch is even more important and tagged for stable series.
It protects one critical section in the syscall entry path by
disabling local interrupts. Without disabling interrupts, the sr7
space register may not be in sync with the current stack setup and
thus an incoming hardware interrupt may destroy memory in random
userspace areas"
* 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Ignore the pkey system calls for now
parisc: Use LINUX_GATEWAY_ADDR define instead of hardcoded value
parisc: Ensure consistent state when switching to kernel stack at syscall entry
parisc: Avoid trashing sr2 and sr3 in LWS code
parisc: use KERN_CONT when printing device inventory
i2c: core: fix NULL pointer dereference under race condition
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
James Hogan [Tue, 1 Nov 2016 13:59:09 +0000 (13:59 +0000)]
MIPS: Fix max_low_pfn with disabled highmem
When low memory doesn't reach HIGHMEM_START (e.g. up to 256MB at PA=0 is
common) and highmem is present above HIGHMEM_START (e.g. on Malta the
RAM overlayed by the IO region is aliased at PA=0x90000000), max_low_pfn
will be initially calculated very large and then clipped down to
HIGHMEM_START.
This causes crashes when reading /sys/kernel/mm/page_idle/bitmap
(i.e. CONFIG_IDLE_PAGE_TRACKING=y) when highmem is disabled. pfn_valid()
will compare against max_mapnr which is derived from max_low_pfn when
there is no highend_pfn set up, and will return true for PFNs right up
to HIGHMEM_START, even though they are beyond the end of low memory and
no page structs will actually exist for these PFNs.
This is fixed by skipping high memory regions when initially calculating
max_low_pfn if highmem is disabled, so it doesn't get clipped too high.
We also clip regions which overlap the highmem boundary when highmem is
disabled, so that max_pfn doesn't extend into highmem either.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14490/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Complement commit 80cbfad79096 ("MIPS: Correct MIPS I FP context
layout") and correct the way Floating Point General registers are stored
in a signal context with MIPS I hardware.
Use the S.D and L.D assembly macros to have pairs of SWC1 instructions
and pairs of LWC1 instructions produced, respectively, in an arrangement
which makes the memory representation of floating-point data passed
compatible with that used by hardware SDC1 and LDC1 instructions, where
available, regardless of the hardware endianness used. This matches the
layout used by r4k_fpu.S, ensuring run-time compatibility for MIPS I
software across all o32 hardware platforms.
Define an EX2 macro to handle exceptions from both hardware instructions
implicitly produced from S.D and L.D assembly macros.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14477/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a regression introduced with commit 2db9ca0a3551 ("MIPS: Use struct
mips_abi offsets to save FP context") for MIPS I/I FP signal contexts,
by converting save/restore code to the updated internal API. Start FGR
offsets from 0 rather than SC_FPREGS from $a0 and use $a1 rather than
the offset of SC_FPC_CSR from $a0 for the Floating Point Control/Status
Register (FCSR).
Document the new internal API and adjust assembly code formatting for
consistency.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14476/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Complement commit e50c0a8fa60d ("Support the MIPS32 / MIPS64 DSP ASE.")
and remove the Floating Point Implementation Register (FIR) from the FP
register set recorded in a signal context with MIPS I processors too, in
line with the change applied to r4k_fpu.S.
The `sc_fpc_eir' slot is unused according to our current ABI and the FIR
register is read-only and always directly accessible from user software.
[ralf@linux-mips.org: This is also required because the next commit depends
on it.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14475/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: Fix ISA I FP sigcontext access violation handling
Complement commit 0ae8dceaebe3 ("Merge with 2.3.10.") and use the local
`fault' handler to recover from FP sigcontext access violation faults,
like corresponding code does in r4k_fpu.S. The `bad_stack' handler is
in syscall.c and is not suitable here as we want to propagate the error
condition up through the caller rather than killing the thread outright.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14474/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* commit 443c44032a54 ("MIPS: Always clear FCSR cause bits after
emulation"),
* commit 64bedffe4968 ("MIPS: Clear [MSA]FPE CSR.Cause after
notify_die()"),
* commit b1442d39fac2 ("MIPS: Prevent user from setting FCSR cause
bits"),
* commit b54d2901517d ("Properly handle branch delay slots in connection
with signals.").
Specifically do not mask these bits out in ptrace(2) processing and send
a SIGFPE signal instead whenever a matching pair of an FCSR Cause and
Enable bit is seen as execution of an affected context is about to
resume. Only then clear Cause bits, and even then do not clear any bits
that are set but masked with the respective Enable bits. Adjust Cause
bit clearing throughout code likewise, except within the FPU emulator
proper where they are set according to IEEE 754 exceptions raised as the
operation emulated executed. Do so so that any IEEE 754 exceptions
subject to their default handling are recorded like with operations
executed by FPU hardware.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14460/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: ptrace: Also initialize the FP context on individual FCSR writes
Complement commit ac9ad83bc318 ("MIPS: prevent FP context set via ptrace
being discarded") and also initialize the FP context whenever FCSR alone
is written with a PTRACE_POKEUSR request addressing FPC_CSR, rather than
along with the full FPU register set in the case of the PTRACE_SETFPREGS
request.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14459/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 21 Oct 2016 19:06:40 +0000 (20:06 +0100)]
MIPS: dump_tlb: Fix printk continuations
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from TLB dumps on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Continuation is also used for the second line of each TLB entry printed
in dump_tlb.c even though it has a newline, since it is a continuation
of the interpretation of the same TLB entry. For example:
Paul Burton [Wed, 19 Oct 2016 13:33:23 +0000 (14:33 +0100)]
MIPS: Fix __show_regs() output
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from __show_regs() on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected register output.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14432/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:22 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_code
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_code on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14431/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:21 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_stacktrace
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_stacktrace on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output. Also
start a new line with printk such that the presence of timing
information does not interfere with output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14430/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 19 Oct 2016 13:33:20 +0000 (14:33 +0100)]
MIPS: traps: Fix output of show_backtrace
Since commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_backtrace on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14429/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Mon, 17 Oct 2016 09:09:39 +0000 (10:09 +0100)]
MIPS: Fix build of compressed image
Changes introduced to arch/mips/Makefile for the generic kernel resulted
in build errors when making a compressed image if platform-y has multiple
values, like this:
make[2]: *** No rule to make target `alchemy/'.
make[1]: *** [vmlinuz] Error 2
make[1]: Target `_all' not remade because of errors.
make: *** [sub-make] Error 2
make: Target `_all' not remade because of errors.
Fix this by quoting $(platform-y) as it is passed to the Makefile in
arch/mips/boot/compressed/Makefile
Matt Redfearn [Mon, 17 Oct 2016 16:25:24 +0000 (17:25 +0100)]
MIPS: generic: Fix KASLR for generic kernel.
The KASLR code requires that the plat_get_fdt() function return the
address of the device tree, and it must be available early in the boot,
before prom_init() is called. Move the code determining the address of
the device tree into plat_get_fdt, and call that from prom_init().
The fdt pointer will be set up by plat_get_fdt() called from
relocate_kernel initially and once the relocated kernel has started,
prom_init() will use it again to determine the address in the relocated
image.
Matt Redfearn [Mon, 17 Oct 2016 16:21:46 +0000 (17:21 +0100)]
MIPS: KASLR: Fix handling of NULL FDT
If platform code returns a NULL pointer to the FDT, initial_boot_params
will not get set to a valid pointer and attempting to find the /chosen
node in it will cause a NULL pointer dereference and the kernel to crash
immediately on startup - with no output to the console.
Fix this by checking that initial_boot_params is valid before using it.
Paul Burton [Fri, 14 Oct 2016 09:17:32 +0000 (10:17 +0100)]
MIPS: Malta: Fixup reboot
Commit 10b6ea0959de ("MIPS: Malta: Use syscon-reboot driver to reboot")
converted the Malta board to use the generic syscon-reboot driver to
handle reboots, but incorrectly used the value 0x4d rather than 0x42 as
the magic to write to the reboot register.
I also incorrectly believed that syscon/regmap would default to native
endianness, but this isn't the case. Force this by specifying with a
native-endian property in the devicetree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 10b6ea0959de ("MIPS: Malta: Use syscon-reboot driver to reboot") Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: linux-mips@linux-mips.org Tested-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14396/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Sat, 15 Oct 2016 22:03:43 +0000 (23:03 +0100)]
MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC
Provide a default implementation of mips_cpc_default_phys_base() which
simply returns 0, and adjust mips_cpc_phys_base() to allow for
mips_cpc_default_phys_base() returning 0. This allows kernels which
include CPC support to be built without platform code & simply ignore
the CPC if it wasn't already enabled by the bootloader.
This fixes link failures such as the following from generic defconfigs:
arch/mips/built-in.o: In function `mips_cpc_phys_base':
arch/mips/kernel/mips-cpc.c:47: undefined reference to `mips_cpc_default_phys_base'
[ralf@linux-mips.org: changed prototype for coding style compliance.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14401/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Borislav Petkov [Sat, 29 Oct 2016 11:17:40 +0000 (13:17 +0200)]
HID: intel-ish-hid: Fix !CONFIG_PM build warning
Fix
drivers/hid/intel-ish-hid/ipc/pci-ish.c:247:12: warning: ‘ish_suspend’ defined but not used [-Wunused-function]
static int ish_suspend(struct device *device)
^
drivers/hid/intel-ish-hid/ipc/pci-ish.c:282:12: warning: ‘ish_resume’ defined but not used [-Wunused-function]
static int ish_resume(struct device *device)
^
by sticking them in the CONFIG_PM range too.
HID: sensor-hub: Fix packing of result buffer for feature report
When report count is more than one and report size is not 4 bytes, then we
need some packing into result buffer from the caller of function
sensor_hub_get_feature.
By default the value extracted from a field is 4 bytes from hid core
(using hid_hw_request(hsdev->hdev, report, HID_REQ_GET_REPORT)), even
if report size if less than 4 byte. So when we copy data to user buffer in
sensor_hub_get_feature, we need to only copy report size bytes even
when report count is more than 1. This is
not an issue for most of the sensor hub fields as report count will be 1
where we already copy only report size bytes, but some string fields
like description, it is a problem as the report count will be more than 1.
For example:
Field(6)
Physical(Sensor.OtherCustom)
Application(Sensor.Sensor)
Usage(11)
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Sensor.0306
Report Size(16)
Report Count(11)
Here since the report size is 2 bytes, we will have 2 additional bytes of
0s copied into user buffer, if we directly copy to user buffer from
report->field[]->value
This change will copy report size bytes into the buffer of caller for each
usage report->field[]->value. So for example without this change, the
data displayed for a custom sensor field "sensor-model":
76 00 101 00 110 00 111 00 118 00 111
(truncated to report count of 11)
RFC 2734 defines the datagram_size field in fragment encapsulation
headers thus:
datagram_size: The encoded size of the entire IP datagram. The
value of datagram_size [...] SHALL be one less than the value of
Total Length in the datagram's IP header (see STD 5, RFC 791).
Accordingly, the eth1394 driver of Linux 2.6.36 and older set and got
this field with a -/+1 offset:
Likewise, I observe OS X 10.4 and Windows XP Pro SP3 to transmit 1500
byte sized datagrams in fragments with datagram_size=1499 if link
fragmentation is required.
Only firewire-net sets and gets datagram_size without this offset. The
result is lacking interoperability of firewire-net with OS X, Windows
XP, and presumably Linux' eth1394. (I did not test with the latter.)
For example, FTP data transfers to a Linux firewire-net box with max_rec
smaller than the 1500 bytes MTU
- from OS X fail entirely,
- from Win XP start out with a bunch of fragmented datagrams which
time out, then continue with unfragmented datagrams because Win XP
temporarily reduces the MTU to 576 bytes.
So let's fix firewire-net's datagram_size accessors.
Note that firewire-net thereby loses interoperability with unpatched
firewire-net, but only if link fragmentation is employed. (This happens
with large broadcast datagrams, and with large datagrams on several
FireWire CardBus cards with smaller max_rec than equivalent PCI cards,
and it can be worked around by setting a small enough MTU.)
Cc: stable@vger.kernel.org Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 29 Oct 2016 19:28:18 +0000 (21:28 +0200)]
firewire: net: guard against rx buffer overflows
The IP-over-1394 driver firewire-net lacked input validation when
handling incoming fragmented datagrams. A maliciously formed fragment
with a respectively large datagram_offset would cause a memcpy past the
datagram buffer.
So, drop any packets carrying a fragment with offset + length larger
than datagram_size.
In addition, ensure that
- GASP header, unfragmented encapsulation header, or fragment
encapsulation header actually exists before we access it,
- the encapsulated datagram or fragment is of nonzero size.
Linus Torvalds [Tue, 1 Nov 2016 23:47:18 +0000 (17:47 -0600)]
sched/core: Remove pointless printout in sched_show_task()
In sched_show_task() we print out a useless hex number, not even a
symbol, and there's a big question mark whether this even makes sense
anyway, I suspect we should just remove it all.
Tetsuo Handa [Wed, 2 Nov 2016 10:50:29 +0000 (19:50 +0900)]
sched/core: Fix oops in sched_show_task()
When CONFIG_THREAD_INFO_IN_TASK=y, it is possible that an exited thread
remains in the task list after its stack pointer was already set to NULL.
Therefore, thread_saved_pc() and stack_not_used() in sched_show_task()
will trigger NULL pointer dereference if an attempt to dump such thread's
traces (e.g. SysRq-t, khungtaskd) is made.
Since show_stack() in sched_show_task() calls try_get_task_stack() and
sched_show_task() is called from interrupt context, calling
try_get_task_stack() from sched_show_task() will be safe as well.
Dave Airlie [Thu, 3 Nov 2016 00:18:20 +0000 (10:18 +1000)]
Merge tag 'drm-intel-fixes-2016-11-01' of git://anongit.freedesktop.org/drm-intel into drm-fixes
batch of scattered i915 fixes.
* tag 'drm-intel-fixes-2016-11-01' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
drm/i915: Remove two invalid warns
drm/i915: Rotated view does not need a fence
drm/i915/fbc: fix CFB size calculation for gen8+
drm: i915: Wait for fences on new fb, not old
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: fix watermarks when using the pipe scaler
drm/i915: Fix mismatched INIT power domain disabling during suspend
drm/i915: fix a read size argument
drm/i915: Use fence_write() from rpm resume
drm/i915/gen9: fix DDB partitioning for multi-screen cases
drm/i915: workaround sparse warning on variable length arrays
drm/i915: keep declarations in i915_drv.h
Dave Airlie [Thu, 3 Nov 2016 00:17:50 +0000 (10:17 +1000)]
Merge tag 'imx-drm-fixes-20161021' of git://git.pengutronix.de/pza/linux into drm-fixes
imx-drm plane, build warning, and error handling fixes
- some fixes for active plane reconfiguration support
- hide unused label in case of disabled CONFIG_DRM_FBDEV_EMULATION,
which caused a build warning
- fixed error handling in imx_drm_bind
- disallow odd x/y plane offsets for chroma subsampled formats
- disable local alpha when switching from a format with alpha
channel to an opaque format
* tag 'imx-drm-fixes-20161021' of git://git.pengutronix.de/pza/linux:
drm/imx: ipuv3-plane: disable local alpha for planes without alpha channel
drm/imx: ipuv3-plane: make sure x/y offsets are even in case of chroma subsampling
drm/imx: ipuv3-plane: Access old u/vbo properly in ->atomic_check for YU12/YV12
drm/imx: drm_dev_alloc() returns error pointers
drm/imx: ipuv3-plane: Skip setting u/vbo only when we don't need modeset
drm/imx: ipuv3-plane: Switch EBA buffer only when we don't need modeset
gpu: ipu-v3: Use ERR_CAST instead of ERR_PTR(PTR_ERR())
drm/imx: hide an unused label
Gerd Hoffmann [Tue, 18 Oct 2016 17:32:30 +0000 (15:32 -0200)]
virtio-gpu: fix vblank events
virtio-gpu sends vblank events in virtio_gpu_crtc_atomic_flush, and
because of that it must be called for disabled planes too. Ask
drm_atomic_helper_commit_planes to do that.
v2: update to use new drm_atomic_helper_commit_planes() API.
parisc: Ensure consistent state when switching to kernel stack at syscall entry
We have one critical section in the syscall entry path in which we switch from
the userspace stack to kernel stack. In the event of an external interrupt, the
interrupt code distinguishes between those two states by analyzing the value of
sr7. If sr7 is zero, it uses the kernel stack. Therefore it's important, that
the value of sr7 is in sync with the currently enabled stack.
This patch now disables interrupts while executing the critical section. This
prevents the interrupt handler to possibly see an inconsistent state which in
the worst case can lead to crashes.
Interestingly, in the syscall exit path interrupts were already disabled in the
critical section which switches back to the userspace stack.
Cc: <stable@vger.kernel.org> Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
There is no need to trash sr2 and sr3 in the Light-weight syscall (LWS). sr2
already points to kernel space (it's zero in userspace, otherwise syscalls
wouldn't work), and since the LWS code is executed in userspace, we can simply
ignore to preload sr3.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
Owen Hofmann [Thu, 27 Oct 2016 18:25:52 +0000 (11:25 -0700)]
kvm: x86: Check memopp before dereference (CVE-2016-8630)
Commit 41061cdb98 ("KVM: emulate: do not initialize memopp") removes a
check for non-NULL under incorrect assumptions. An undefined instruction
with a ModR/M byte with Mod=0 and R/M-5 (e.g. 0xc7 0x15) will attempt
to dereference a null pointer here.
Jim Mattson [Fri, 28 Oct 2016 15:29:39 +0000 (08:29 -0700)]
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
After a successful VM-entry with the "VMCS shadowing" VM-execution
control set, the shadow VMCS referenced by the VMCS link pointer field
in the current VMCS becomes active on the logical processor.
A VMCS that is made active on more than one logical processor may become
corrupted. Therefore, before an active VMCS can be migrated to another
logical processor, the first logical processor must execute a VMCLEAR
for the active VMCS. VMCLEAR both ensures that all VMCS data are written
to memory and makes the VMCS inactive.
Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-By: David Matlack <dmatlack@google.com>
Message-Id: <1477668579-22555-1-git-send-email-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 31 Oct 2016 23:39:48 +0000 (00:39 +0100)]
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
Since commit a545ab6a0085 ("kvm: x86: add tsc_offset field to struct
kvm_vcpu_arch", 2016-09-07) the offset between host and L1 TSC is
cached and need not be fished out of the VMCS or VMCB. This means
that we can implement adjust_tsc_offset_guest and read_l1_tsc
entirely in generic code. The simplification is particularly
significant for VMX code, where vmx->nested.vmcs01_tsc_offset
was duplicating what is now in vcpu->arch.tsc_offset. Therefore
the vmcs01_tsc_offset can be dropped completely.
More importantly, this fixes KVM_GET_CLOCK/KVM_SET_CLOCK
which, after commit 108b249c453d ("KVM: x86: introduce get_kvmclock_ns",
2016-09-01) called read_l1_tsc while the VMCS was not loaded.
It thus returned bogus values on Intel CPUs.
Fixes: 108b249c453dd7132599ab6dc7e435a7036c193f Reported-by: Roman Kagan <rkagan@virtuozzo.com> Reviewed-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Tue, 1 Nov 2016 23:48:46 +0000 (17:48 -0600)]
Merge tag 'gcc-plugins-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugin fixes from Kees Cook:
- make sure required exports from gcc plugins are visible to gcc
- switch latent_entropy to unsigned long to avoid stack frame bloat
* tag 'gcc-plugins-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Fix wrong gcc code generation with 64 bit variables
gcc-plugins: Export symbols needed by gcc
Linus Torvalds [Tue, 1 Nov 2016 22:56:05 +0000 (16:56 -0600)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Tests, fixes and cleanups.
Just minor tweaks, there's nothing major in this cycle"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_ring: mark vring_dma_dev inline
virtio/vhost: add Jason to list of maintainers
virtio_blk: Delete an unnecessary initialisation in init_vq()
virtio_blk: Use kmalloc_array() in init_vq()
virtio: remove config.c
virtio: console: Unlock vqs while freeing buffers
ringtest: poll for new buffers once before updating event index
ringtest: commonize implementation of poll_avail/poll_used
ringtest: use link-time optimization
virtio: update balloon size in balloon "probe"
virtio_ring: Make interrupt suppression spec compliant
virtio_pci: Limit DMA mask to 44 bits for legacy virtio devices
Jeff Layton says:
> Hm...now that I look though, this is a little suspicious:
>
> struct nfs4_openowner *oo = openowner(stp->st_openstp->st_stateowner);
>
> I wonder if it's possible for the openstateid to have already been
> destroyed at this point.
>
> We might be better off doing something like this to get the client pointer:
>
> stp->st_stid.sc_client;
>
> ...which should be more direct and less dependent on other stateids
> staying valid.
With the suggested change, I am no longer able to reproduce the above oops.
v2: Fix unhash_lock_stateid() as well
Fix-suggested-by: Jeff Layton <jlayton@redhat.com> Fixes: 42691398be08 ('nfsd: Fix race between FREE_STATEID and LOCK') Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Chuck Lever [Sat, 29 Oct 2016 02:22:33 +0000 (22:22 -0400)]
svcrdma: backchannel cannot share a page for send and rcv buffers
The underlying transport releases the page pointed to by rq_buffer
during xprt_rdma_bc_send_request. When the backchannel reply arrives,
rq_rbuffer then points to freed memory.
Fixes: 68778945e46f ('SUNRPC: Separate buffer pointers for RPC ...') Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
projects / karo-tx-linux.git / log