Dirk Brandewie [Wed, 6 Feb 2013 17:02:08 +0000 (09:02 -0800)]
cpufreq: Retrieve current frequency from scaling drivers with internal governors
Scaling drivers that implement the cpufreq_driver.setpolicy() versus
the cpufreq_driver.target() interface do not set policy->cur.
Normally policy->cur is set during the call to cpufreq_driver.target()
when the frequnecy request is made by the governor.
If the scaling driver implements cpufreq_driver.setpolicy() and
cpufreq_driver.get() interfaces use cpufreq_driver.get() to retrieve
the current frequency.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 7 Feb 2013 05:25:00 +0000 (10:55 +0530)]
cpufreq: Fix locking issues
cpufreq core uses two locks:
- cpufreq_driver_lock: General lock for driver and cpufreq_cpu_data array.
- cpu_policy_rwsemfix locking: per CPU reader-writer semaphore designed to cure
all cpufreq/hotplug/workqueue/etc related lock issues.
These locks were not used properly and are placed against their principle
(present before their definition) at various places. This patch is an attempt to
fix their use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 7 Feb 2013 07:21:27 +0000 (12:51 +0530)]
cpufreq: governors: Fix WARN_ON() for multi-policy platforms
On multi-policy systems there is a single instance of governor for both the
policies (if same governor is chosen for both policies). With the code update
from following patches:
8eeed09 cpufreq: governors: Get rid of dbs_data->enable field b394058 cpufreq: governors: Reset tunables only for cpufreq_unregister_governor()
We are creating/removing sysfs directory of governor for for every call to
GOV_START and STOP. This would fail for multi-policy system as there is a
per-policy call to START/STOP.
This patch reuses the governor->initialized variable to detect total users of
governor.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: ondemand: Replace down_differential tuner with adj_up_threshold
In order to avoid the calculation of up_threshold - down_differential
every time that the frequency must be decreased, we replace the
down_differential tuner with the adj_up_threshold which keeps the
difference across multiple checks.
Update the adj_up_threshold only when the up_theshold is also updated.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Mon, 4 Feb 2013 11:38:52 +0000 (11:38 +0000)]
cpufreq / stats: Get rid of CPUFREQ_STATDEVICE_ATTR
Macro "CPUFREQ_STATDEVICE_ATTR" is defined local to cpufreq_stats.c file and is
almost a copy of the generic version present in cpufreq.h file. Lets use the
generic version instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Shawn Guo [Mon, 4 Feb 2013 05:46:29 +0000 (05:46 +0000)]
cpufreq: add imx6q-cpufreq driver
Add an imx6q-cpufreq driver for Freescale i.MX6Q SoC to handle the
hardware specific frequency and voltage scaling requirements.
The driver supports module build and is instantiated by the platform
device/driver mechanism, so that it will not be instantiated on other
platforms, as IMX is built with multiplatform support.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Tue, 5 Feb 2013 21:21:14 +0000 (22:21 +0100)]
cpufreq: Don't remove sysfs link for policy->cpu
"cpufreq" directory in policy->cpu is never created using
sysfs_create_link(), but using kobject_init_and_add(). And so we
shouldn't call sysfs_remove_link() for policy->cpu(). sysfs stuff
for policy->cpu is automatically removed when we call kobject_put()
for dying policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Tested-by: Dirk Brandewie <dirk.brandewie@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Fri, 1 Feb 2013 06:40:00 +0000 (06:40 +0000)]
cpufreq: TEGRA: Set policy->cpus from driver->init()
For multicore SoC's, with cores sharing clock line, we are required to set
policy->cpus and policy->related_cpus with mask of cpus.
With following patch, we need to set policy->cpus with mask of all possible cpus
and policy->related_cpus would be filled automatically by the cpufreq core.
Viresh Kumar [Fri, 1 Feb 2013 05:42:58 +0000 (05:42 +0000)]
cpufreq: governors: Reset tunables only for cpufreq_unregister_governor()
Currently, whenever governor->governor() is called for CPUFRREQ_GOV_START event
we reset few tunables of governor. Which isn't correct, as this routine is
called for every cpu hot-[un]plugging event. We should actually be resetting
these only when the governor module is removed and re-installed.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fabio Baltieri [Thu, 31 Jan 2013 10:39:19 +0000 (10:39 +0000)]
cpufreq: governors: fix misuse of cdbs.cpu
Fix governors code to set all cpu's cdbs->cpu to the the actual cpu id
and use cur_policy->cpu istead of cdbs->cpu to track current governor's
leader cpu.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Implement a generic helper function policy_is_shared() to replace the
current dbs_sw_coordinated_cpus() at cpufreq level, so that it can be
used by code other than cpufreq governors.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 31 Jan 2013 04:53:56 +0000 (04:53 +0000)]
cpufreq: SPEAr: Notify all policy->cpus of frequency change
SPEAr cpufreq driver supports dual core Cortex-A9 SoC's, where cpus share policy
structure. Whenever we update frequency of a cpu, we must notify all
policy->cpus.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Thu, 31 Jan 2013 02:03:53 +0000 (02:03 +0000)]
cpufreq: Update Documentation for cpus and related_cpus
Documentation related to cpus and related_cpus is confusing and not very clear.
Over that CPUFreq core has seen much changes recently. Lets update documentation
and comments for cpus and related_cpus.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Shawn Guo [Wed, 30 Jan 2013 14:27:49 +0000 (14:27 +0000)]
cpufreq: instantiate cpufreq-cpu0 as a platform_driver
As multiplatform build is being adopted by more and more ARM platforms,
initcall function should be used very carefully. For example, when
GENERIC_CPUFREQ_CPU0 is built in the kernel, cpu0_cpufreq_driver_init()
will be called on all the platforms to initialize cpufreq-cpu0 driver.
To eliminate this undesired the effect, the patch changes cpufreq-cpu0
driver to have it instantiated as a platform_driver. Then it will only
run on platforms that create the platform_device "cpufreq-cpu0".
Along with the change, it also changes cpu_dev to be &pdev->dev,
so that managed functions can start working, and module build gets
supported too.
The highbank-cpufreq driver is also updated accordingly to adapt the
changes on cpufreq-cpu0.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Tue, 29 Jan 2013 14:39:08 +0000 (14:39 +0000)]
cpufreq: Simplify cpufreq_add_dev()
Currently cpufreq_add_dev() firsts allocates policy, calls
driver->init() and then checks if this CPU is already managed or not.
And if it is already managed, its policy is freed.
We can save all this if we somehow know that CPU is managed or not in
advance. policy->related_cpus contains the list of all valid sibling
CPUs of policy->cpu. We can check this to see if the current CPU is
already managed.
From now on, platforms don't really need to set related_cpus from
their init() routines, as the same work is done by core too.
If a platform driver needs to set the related_cpus mask with some
additional CPUs, other than CPUs present in policy->cpus, they are
free to do it, though, as we don't override anything.
[rjw: Changelog] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Mark Langsdorf [Mon, 28 Jan 2013 16:13:15 +0000 (16:13 +0000)]
cpufreq / highbank: add support for highbank cpufreq
Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rob Herring [Mon, 28 Jan 2013 16:13:14 +0000 (16:13 +0000)]
ARM / highbank: add support for pl320 IPC
The pl320 IPC allows for interprocessor communication between the
highbank A9 and the EnergyCore Management Engine. The pl320 implements
a straightforward mailbox protocol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Mark Langsdorf [Mon, 28 Jan 2013 16:13:13 +0000 (16:13 +0000)]
clk / highbank: Prevent glitches in non-bypass reset mode
The highbank clock will glitch with the current code if the
clock rate is reset without relocking the PLL. Program the PLL
correctly to prevent glitches.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rob Herring [Mon, 28 Jan 2013 16:13:12 +0000 (16:13 +0000)]
ARM: use device tree to get smp_twd clock
Move clk setup to twd_local_timer_common_register and rely on
twd_timer_rate being 0 to force calibration if there is no clock.
Remove common_setup_called as it is no longer needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Borislav Petkov [Sun, 20 Jan 2013 10:24:27 +0000 (10:24 +0000)]
cpufreq: Make acpi-cpufreq link first
Now that the majority of x86 CPUs out there are supported by
acpi-cpufreq, we want it to load first and, in the AMD case, drop to
powernow-k8 only on K8s. If, however, both powernow-k8 and acpi-cpufreq
are built-in, the link order matters. Correct that.
Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Matthew Garrett [Sun, 20 Jan 2013 10:24:26 +0000 (10:24 +0000)]
acpi-cpufreq: Do not load on K8
de3ed81d746d ("[CPUFREQ] Change link order of x86 cpufreq modules")
changed cpufreq drivers link order so that powernow-k8 gets loaded first
due to earlier K8s having BIOS bugs.
However, now that acpi-cpufreq supports both AMD and Intel CPUs with HW
P-states, we want to load it first, so that cases where acpi-cpufreq and
powernow-k8 are both built-in and powernow-k8 initializing first, can be
addressed.
So, make sure that even if acpi-cpufreq gets loaded first, it errors out
on K8s and powernow-k8 can be loaded then successfully.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
References: http://lkml.kernel.org/r/20130118162347.GA31499@srcf.ucam.org Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dirk Brandewie [Thu, 17 Jan 2013 16:22:21 +0000 (16:22 +0000)]
cpufreq: handle cpufreq being disabled for all exported function.
When disable_cpufreq() is called some exported functions are still
being used that do not have a check for cpufreq being disabled.
Add a disabled check into cpufreq_cpu_get() to return NULL if
cpufreq is disabled this covers most of the exported functions. For
the exported functions that do not call cpufreq_cpu_get() add an
explicit check.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Mon, 14 Jan 2013 13:23:03 +0000 (13:23 +0000)]
cpufreq: Simplify __cpufreq_remove_dev()
__cpufreq_remove_dev() is called on multiple occasions: cpufreq_driver
unregister and cpu removals.
Current implementation of this routine is overly complex without much need. If
the cpu to be removed is the policy->cpu, we remove the policy first and add all
other cpus again from policy->cpus and then finally call __cpufreq_remove_dev()
again to remove the cpu to be deleted. Haahhhh..
There exist a simple solution to removal of a cpu:
- Simply use the old policy structure
- update its fields like: policy->cpu, etc.
- notify any users of cpufreq, which depend on changing policy->cpu
Hence this patch, which tries to implement the above theory. It is tested well
by myself on ARM big.LITTLE TC2 SoC, which has 5 cores (2 A15 and 3 A7). Both
A15's share same struct policy and all A7's share same policy structure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Sat, 12 Jan 2013 05:14:40 +0000 (05:14 +0000)]
cpufreq: Don't use cpu removed during cpufreq_driver_unregister
This is how the core works:
cpufreq_driver_unregister()
- subsys_interface_unregister()
- for_each_cpu() call cpufreq_remove_dev(), i.e. 0,1,2,3,4 when we
unregister.
cpufreq_remove_dev():
- Remove policy node
- Call cpufreq_add_dev() for next cpu, sharing mask with removed cpu.
i.e. When cpu 0 is removed, we call it for cpu 1. And when called for cpu 2,
we call it for cpu 3.
- cpufreq_add_dev() would call cpufreq_driver->init()
- init would return mask as AND of 2, 3 and 4 for cluster A7.
- cpufreq core would do online_cpu && policy->cpus
Here is the BUG(). Because cpu hasn't died but we have just unregistered
the cpufreq driver, online cpu would still have cpu 2 in it. And so thing
go bad again.
Solution: Keep cpumask of cpus that are registered with cpufreq core and clear
cpus when we get a call from subsys_interface_unregister() via
cpufreq_remove_dev().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Sat, 12 Jan 2013 05:14:39 +0000 (05:14 +0000)]
cpufreq: Notify governors when cpus are hot-[un]plugged
Because cpufreq core and governors worry only about the online cpus, if a cpu is
hot [un]plugged, we must notify governors about it, otherwise be ready to expect
something unexpected.
We already have notifiers in the form of CPUFREQ_GOV_START/CPUFREQ_GOV_STOP, we
just need to call them now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Sat, 12 Jan 2013 05:14:38 +0000 (05:14 +0000)]
cpufreq: Manage only online cpus
cpufreq core doesn't manage offline cpus and if driver->init() has returned
mask including offline cpus, it may result in unwanted behavior by cpufreq core
or governors.
We need to get only online cpus in this mask. There are two places to fix this
mask, cpufreq core and cpufreq driver. It makes sense to do this at common place
and hence is done in core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes a bug that occurred when we had load on a secondary CPU
and the primary CPU was sleeping. Only one sampling timer was spawned
and it was spawned as a deferred timer on the primary CPU, so when a
secondary CPU had a change in load this was not detected by the cpufreq
governor (both ondemand and conservative).
This patch make sure that deferred timers are run on all CPUs in the
case of software controlled CPUs that run on the same frequency.
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com> Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 31 Jan 2013 21:44:59 +0000 (08:44 +1100)]
Merge branch 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
Linus Torvalds [Thu, 31 Jan 2013 21:43:52 +0000 (08:43 +1100)]
Merge tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Error reporting in nfs_xdev_mount incorrectly maps all errors to
ENOMEM
- Fix an NFSv4 refcounting issue
- Fix a mount failure when the server reboots during NFSv4 trunking
discovery
- NFSv4.1 mounts may need to run the lease recovery thread.
- Don't silently fail setattr() requests on mountpoints
- Fix a SUNRPC socket/transport livelock and priority queue issue
- We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.
* tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
SUNRPC: When changing the queue priority, ensure that we change the owner
NFS: Don't silently fail setattr() requests on mountpoints
NFSv4.1: Ensure that nfs41_walk_client_list() does start lease recovery
NFSv4: Fix NFSv4 trunking discovery
NFSv4: Fix NFSv4 reference counting for trunked sessions
NFS: Fix error reporting in nfs_xdev_mount
Linus Torvalds [Thu, 31 Jan 2013 21:43:04 +0000 (08:43 +1100)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"A number of fixes all across the MIPS tree. No area is particularly
standing out and things have cooled down quite nicely for a release."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Function tracer: Fix broken function tracing
mips: Move __virt_addr_valid() to a place for MIPS 64
MIPS: Netlogic: Fix UP compilation on XLR
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
MIPS: Lantiq: Fix cp0_perfcount_irq mapping
MIPS: DSP: Fix DSP mask for registers.
MIPS: Fix build failure by adding definition of pfn_pmd().
MIPS: Octeon: Fix warning.
MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
MIPS: PNX833x: Fix comment.
MIPS: Add struct p_format to union mips_instruction.
MIPS: Export <asm/break.h>.
MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
MIPS: vpe.c: Fix null pointer dereference in print arguments.
i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.
Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.
Reported-by: Andrew Duggan <aduggan@synaptics.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Al Cooper [Wed, 16 Jan 2013 22:43:28 +0000 (22:43 +0000)]
MIPS: Function tracer: Fix broken function tracing
Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439cb43336cd6d7e804ecb2c81193ef63b0
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.
MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.
The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.
Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning. So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.
The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.
This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr". When
disabled, there will be two nops.
This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.
When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.
[ralf@linux-mips.org: Folded in Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com> Cc: rostedt@goodmis.org Cc: ddaney.cavm@gmail.com Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.
Steven Rostedt [Fri, 25 Jan 2013 17:13:15 +0000 (17:13 +0000)]
mips: Move __virt_addr_valid() to a place for MIPS 64
Commit d3ce88431892 "MIPS: Fix modpost error in modules attepting to use
virt_addr_valid()" moved __virt_addr_valid() from a macro in a header
file to a function in ioremap.c. But ioremap.c is only compiled for MIPS
32, and not for MIPS 64.
When compiling for my yeeloong2, which supposedly supports hibernation,
which compiles kernel/power/snapshot.c which calls virt_addr_valid(), I
got this error:
LD init/built-in.o
kernel/built-in.o: In function `memory_bm_free':
snapshot.c:(.text+0x4c9c4): undefined reference to `__virt_addr_valid'
snapshot.c:(.text+0x4ca58): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e44c): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e890): undefined reference to `__virt_addr_valid'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
I suspect that __virt_addr_valid() is fine for mips 64. I moved it to
mmap.c such that it gets compiled for mips 64 and 32.
Mike Snitzer [Thu, 31 Jan 2013 14:11:14 +0000 (14:11 +0000)]
dm thin: fix queue limits stacking
thin_io_hints() is blindly copying the queue limits from the thin-pool
which can lead to incorrect limits being set. The fix here simply
deletes the thin_io_hints() hook which leaves the existing stacking
infrastructure to set the limits correctly.
When a thin-pool uses an MD device for the data device a thin device
from the thin-pool must respect MD's constraints about disallowing a bio
from spanning multiple chunks. Otherwise we can see problems. If the raid0
chunksize is 1152K and thin-pool chunksize is 256K I see the following
md/raid0 error (with extra debug tracing added to thin_endio) when
mkfs.xfs is executed against the thin device:
md/raid0:md99: make_request bug: can't convert block across chunks or bigger than 1152k 6688 127
device-mapper: thin: bio sector=2080 err=-5 bi_size=130560 bi_rw=17 bi_vcnt=32 bi_idx=0
This extra DM debugging shows that the failing bio is spanning across
the first and second logical 1152K chunk (sector 2080 + 255 takes the
bio beyond the first chunk's boundary of sector 2304). So the bio
splitting that DM is doing clearly isn't respecting the MD limits.
max_hw_sectors_kb is 127 for both the thin-pool and thin device
(queue_max_hw_sectors returns 255 so we'll excuse sysfs's lack of
precision). So this explains why bi_size is 130560.
But the thin device's max_hw_sectors_kb should be 4 (PAGE_SIZE) given
that it doesn't have a .merge function (for bio_add_page to consult
indirectly via dm_merge_bvec) yet the thin-pool does sit above an MD
device that has a compulsory merge_bvec_fn. This scenario is exactly
why DM must resort to sending single PAGE_SIZE bios to the underlying
layer. Some additional context for this is available in the header for
commit 8cbeb67a ("dm: avoid unsupported spanning of md stripe boundaries").
Long story short, the reason a thin device doesn't properly get
configured to have a max_hw_sectors_kb of 4 (PAGE_SIZE) is that
thin_io_hints() is blindly copying the queue limits from the thin-pool
device directly to the thin device's queue limits.
Fix this by eliminating thin_io_hints. Doing so is safe because the
block layer's queue limits stacking already enables the upper level thin
device to inherit the thin-pool device's discard and minimum_io_size and
optimal_io_size limits that get set in pool_io_hints. But avoiding the
queue limits copy allows the thin and thin-pool limits to be different
where it is important, namely max_hw_sectors_kb.
Reported-by: Daniel Browning <db@kavod.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Linus Torvalds [Thu, 31 Jan 2013 06:10:36 +0000 (17:10 +1100)]
Merge branch 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
Linus Torvalds [Thu, 31 Jan 2013 06:08:43 +0000 (17:08 +1100)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Linus Torvalds [Thu, 31 Jan 2013 06:04:46 +0000 (17:04 +1100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull console lockdep checking revert from Dave Airlie.
The lockdep splat this showed was interesting, but it's very very old,
and we won't be fixing it until 3.9. In the meantime, undo the lockdep
annotation so that we don't generate the (known) console lockdep issue,
and then possibly hide any potential other (unknown) lockdep problems
that got disabled by the first one that triggered.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "console: implement lockdep support for console_lock"
Trond Myklebust [Wed, 30 Jan 2013 18:04:10 +0000 (13:04 -0500)]
NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
NFS4ERR_DELAY is a legal reply when we call DESTROY_SESSION. It
usually means that the server is busy handling an unfinished RPC
request. Just sleep for a second and then retry.
We also need to be able to handle the NFS4ERR_BACK_CHAN_BUSY return
value. If the NFS server has outstanding callbacks, we just want to
similarly sleep & retry.
Trond Myklebust [Sun, 27 Jan 2013 19:20:49 +0000 (14:20 -0500)]
SUNRPC: When changing the queue priority, ensure that we change the owner
This fixes a livelock in the xprt->sending queue where we end up never
making progress on lower priority tasks because sleep_on_priority()
keeps adding new tasks with the same owner to the head of the queue,
and priority bumps mean that we keep resetting the queue->owner to
whatever task is at the head of the queue.
H. Peter Anvin [Wed, 30 Jan 2013 22:43:05 +0000 (14:43 -0800)]
Merge tag 'efi-for-3.8' into x86/efi
Various urgent EFI fixes and some warning cleanups for v3.8
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Trond Myklebust [Tue, 22 Jan 2013 05:17:06 +0000 (00:17 -0500)]
NFS: Don't silently fail setattr() requests on mountpoints
Ensure that any setattr and getattr requests for junctions and/or
mountpoints are sent to the server. Ever since commit 0ec26fd0698 (vfs: automount should ignore LOOKUP_FOLLOW), we have
silently dropped any setattr requests to a server-side mountpoint.
For referrals, we have silently dropped both getattr and setattr
requests.
This patch restores the original behaviour for setattr on mountpoints,
and tries to do the same for referrals, provided that we have a
filehandle...
Gabor Juhos [Tue, 29 Jan 2013 08:27:04 +0000 (08:27 +0000)]
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
The base address of the PCI memory is 0x10000000 and the base address of the
PCI configuration space is 0x17000000 on the AR71xx SoCs.
The AR71XX_PCI_MEM_SIZE is defined as 0x08000000 which is wrong because that
overlaps with the configuration space. This patch fixes the value of the
AR71XX_PCI_MEM_SIZE constant, in order to avoid this resource conflicts.
Matt Fleming [Thu, 3 Jan 2013 09:02:37 +0000 (09:02 +0000)]
samsung-laptop: Disable on EFI hardware
It has been reported that running this driver on some Samsung laptops
with EFI can cause those machines to become bricked as detailed in the
following report,
There have also been reports of this driver causing Machine Check
Exceptions on recent EFI-enabled Samsung laptops,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
So disable it if booting from EFI since this driver relies on
grovelling around in the BIOS memory map which isn't going to work.
Cc: Corentin Chary <corentincj@iksaif.net> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Colin Ian King <colin.king@canonical.com> Cc: Steve Langasek <steve.langasek@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Matt Fleming [Wed, 14 Nov 2012 09:42:35 +0000 (09:42 +0000)]
efi: Make 'efi_enabled' a function to query EFI facilities
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie> Cc: Corentin Chary <corentincj@iksaif.net> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Dave Jiang <dave.jiang@intel.com> Cc: Olof Johansson <olof@lixom.net> Cc: Peter Jones <pjones@redhat.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Steve Langasek <steve.langasek@canonical.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Konrad Rzeszutek Wilk <konrad@kernel.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: <stable@vger.kernel.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Linus Torvalds [Wed, 30 Jan 2013 11:32:48 +0000 (22:32 +1100)]
Merge tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixlets from Borislav Petkov:
"Two minor correctness fixlets from Dan Carpenter and Joe Perches each."
* tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Fix kcalloc argument order
EDAC: Test correct variable in ->store function
Linus Torvalds [Wed, 30 Jan 2013 11:20:48 +0000 (22:20 +1100)]
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- A collection of small ASoC driver fixes (error path fixes, register
correction, regulator bypass mode fix, etc)
- A few regression fixes and quirks of HD-audio (wrong page attributes
for SG-buffer, Poulsbo/Oaktrail controller fix, digital mic fix for
Acer, etc)
- A fix for USB-audio UAC2 devices wrt FU length check
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix non-snoop page handling
ALSA: hda - Enable LPIB delay count for Poulsbo / Oaktrail
ALSA: hda - fix inverted internal mic on Acer AOA150/ZG5
ALSA: usb-audio: fix invalid length check for RME and other UAC 2 devices
ALSA: hda - Add a fixup for Packard-Bell desktop with ALC880
ASoC: wm_adsp: Release firmware on error
ASoC: wm_adsp: Use GFP_DMA for things that may be DMAed
ASoC: arizona: Use actual rather than desired BCLK when calculating LRCLK
ASoC: wm2200: correct mixer values and text
ASoC: MAINTAINERS: Update email address.
ASoC: wm5110: Correct AEC loopback mask
ASoC: wm5102: Correct AEC loopback mask
ASoC: dapm: Fix sense of regulator bypass mode
ASoC: fsl: fix multiple definition of init_module
ASoC: arizona: Disable free-running mode on FLL1
Linus Torvalds [Wed, 30 Jan 2013 01:02:26 +0000 (12:02 +1100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Intel, radeon and exynos fixes. Nothing too major or wierd: one dmar
fix and a radeon cursor corruption, along with misc exynos fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (21 commits)
drm/exynos: add check for the device power status
drm/exynos: Make 'drm_hdmi_get_edid' static
drm/exynos: fimd and ipp are broken on multiplatform
drm/exynos: don't include plat/gpio-cfg.h
drm/exynos: Remove "internal" interrupt handling
drm/exynos: Add missing static specifiers in exynos_drm_rotator.c
drm/exynos: Replace mdelay with usleep_range
drm/exynos: Make ipp_handle_cmd_work static
drm/exynos: Make g2d_userptr_get_dma_addr static
drm/exynos: consider DMA_NONE flag to dmabuf import
drm/exynos: free sg object if dma_map_sg is failed
drm/exynos: added validation of edid for vidi connection
drm/exynos: let drm handle edid allocations
drm/radeon: Enable DMA_IB_SWAP_ENABLE on big endian hosts.
drm/radeon: fix a rare case of double kfree
radeon_display: Use pointer return error codes
drm/radeon: fix cursor corruption on DCE6 and newer
drm/i915: dump UTS_RELEASE into the error_state
iommu/intel: disable DMAR for g4x integrated gfx
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
...
Linus Torvalds [Wed, 30 Jan 2013 00:59:37 +0000 (11:59 +1100)]
Merge tag 'for-linus-v3.8-rc6' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
"Here are fixes for returning EFSCORRUPTED on probe of a non-xfs
filesystem, the stack switch in xfs_bmapi_allocate, a crash in
_xfs_buf_find, speculative preallocation as the filesystem nears
ENOSPC, an unmount hang, a race with AIO, and a regression with
xfs_fsr:
- fix return value when filesystem probe finds no XFS magic, a
regression introduced in 9802182.
- fix stack switch in __xfs_bmapi_allocate by moving the check for
stack switch up into xfs_bmapi_write.
- fix oops in _xfs_buf_find by validating that the requested block is
within the filesystem bounds.
- limit speculative preallocation near ENOSPC.
- fix an unmount hang in xfs_wait_buftarg by freeing the
xfs_buf_log_item in xfs_buf_item_unlock.
- fix a possible use after free with AIO.
- fix xfs_swap_extents after removal of xfs_flushinval_pages, a
regression introduced in commit fb59581404a."
* tag 'for-linus-v3.8-rc6' of git://oss.sgi.com/xfs/xfs:
xfs: Fix xfs_swap_extents() after removal of xfs_flushinval_pages()
xfs: Fix possible use-after-free with AIO
xfs: fix shutdown hang on invalid inode during create
xfs: limit speculative prealloc near ENOSPC thresholds
xfs: fix _xfs_buf_find oops on blocks beyond the filesystem end
xfs: pull up stack_switch check into xfs_bmapi_write
xfs: Do not return EFSCORRUPTED when filesystem probe finds no XFS magic
Linus Torvalds [Wed, 30 Jan 2013 00:58:26 +0000 (11:58 +1100)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull one s390 fix from Martin Schwidefsky:
"Another transparent huge page fix, we need to define a s390 variant
for pmdp_set_wrprotect to flush the TLB for the huge page correctly."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/thp: implement pmdp_set_wrprotect()
Linus Torvalds [Wed, 30 Jan 2013 00:34:50 +0000 (11:34 +1100)]
Merge tag 'pinctrl-fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"This is a late pinctrl fix pull request, we had to revert out the
pinctrl-single GPIO backend, because of, well, design issues. We're
cooking a better thing for the next cycle.
- Revert gpio request/free backend, new patch set in the works, will
be for v3.9. Get this old cruft out before anyone hurts himself on
it.
- Kconfig buzz
- Various compile warnings
- MPP6 value for the Kirkwood"
* tag 'pinctrl-fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: nomadik: nmk_prcm_gpiocr_get_mode may be unused
pinctrl: exynos: don't mark probing functions as __init
Revert "pinctrl: single: support gpio request and free"
pinctrl: mvebu: fix MPP6 value for kirkwood driver
pinctrl: mvebu: Fix compiler warnings
pinctrl: pinctrl-mxs: Fix variables' definition type
pinctrl: samsung: removing duplicated condition for PINCTRL_SAMSUNG
Arnd Bergmann [Fri, 25 Jan 2013 14:14:30 +0000 (14:14 +0000)]
pinctrl: nomadik: nmk_prcm_gpiocr_get_mode may be unused
nmk_prcm_gpiocr_get_mode is only needed for debugfs output at
the moment, which can be compile-time disabled. Marking
the function __maybe_unused still gives us compile-time
coverage, but avoids a gcc warning.
Without this patch, building nhk8815_defconfig results in:
drivers/pinctrl/pinctrl-nomadik.c:676:12: warning: 'nmk_prcm_gpiocr_get_mode' defined but not used [-Wunused-function]
Arnd Bergmann [Fri, 25 Jan 2013 14:14:29 +0000 (14:14 +0000)]
pinctrl: exynos: don't mark probing functions as __init
Functions called from a driver probe() method must not be
marked __init, because they may get called after the
init phase is done, when the device shows up late, or
because of deferred probing.
Without this patch, building exynos_defconfig results in
multiple warnings like:
WARNING: drivers/pinctrl/built-in.o(.text+0x51bc): Section mismatch in reference from the function exynos5440_pinctrl_probe() to the function .init.text:exynos5440_gpiolib_register()
The function exynos5440_pinctrl_probe() references
the function __init exynos5440_gpiolib_register().
This is often because exynos5440_pinctrl_probe lacks a __init
annotation or the annotation of exynos5440_gpiolib_register is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Tomasz Figa <t.figa@samsung.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
x86, efi: remove attribute check from setup_efi_pci
It looks like the original commit that copied the rom contents from
efi always copied the rom, and the fixup in setup_efi_pci from commit 886d751a2ea99a160 ("x86, efi: correct precedence of operators in
setup_efi_pci") broke that.
This resulted in macbook pro's no longer finding the rom images, and
thus not being able to use the radeon card any more.
The solution is to just remove the check for now, and always copy the
rom if available.
Takashi Iwai [Tue, 29 Jan 2013 17:07:22 +0000 (18:07 +0100)]
ALSA: hda - Fix non-snoop page handling
For non-snoop mode, we fiddle with the page attributes of CORB/RIRB
and the position buffer, but also the ring buffers. The problem is
that the current code blindly assumes that the buffer is contiguous.
However, the ring buffers may be SG-buffers, thus a wrong vmapped
address is passed there, leading to Oops.
Currently we use LPIB forcibly for both playback and capture for
Poulsbo and Oaktrail devices, and this seems rather problematic.
The recent fix for LPIB delay count seems working well with these
devices, so let's enable it instead.
Reported-by: Martin Weishart <martin.weishart@telosalliance.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 29 Jan 2013 06:44:53 +0000 (22:44 -0800)]
Merge tag 'regulator-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Fairly small stuff - a build failure fix for ST platforms, an error
checking fix and an update to the MAINTAINERS file for Liam."
* tag 'regulator-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps80031: Use IS_ERR to check return value of regulator_register()
regulators: db8500: Fix compile failure for drivers/regulator/dbx500-prcmu.c
regulator: MAINTAINERS: update email address
Linus Torvalds [Tue, 29 Jan 2013 00:23:07 +0000 (16:23 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Whenever you have a chance between two dives, you might want to
consider pulling my merge branch to pickup a few fixes for 3.8 that
have been accumulating for the last couple of weeks (I was myself
travelling then on vacation).
Nothing major, just a handful of powerpc bug fixes that I consider
worth getting in before 3.8 goes final."
And I'll have everybody know that I'm not diving for several days yet.
Snif.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Max next_tb to prevent from replaying timer interrupt
powerpc: kernel/kgdb.c: Fix memory leakage
powerpc/book3e: Disable interrupt after preempt_schedule_irq
powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() function
powerpc/pasemi: Fix crash on reboot
powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32
Tiejun Chen [Tue, 15 Jan 2013 17:01:19 +0000 (17:01 +0000)]
powerpc: Max next_tb to prevent from replaying timer interrupt
With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Sun, 6 Jan 2013 00:49:34 +0000 (00:49 +0000)]
powerpc/book3e: Disable interrupt after preempt_schedule_irq
In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> CC: <stable@vger.kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Carl E. Love [Thu, 29 Nov 2012 06:42:03 +0000 (06:42 +0000)]
powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() function
The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error. The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width. However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH. This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Mon, 21 Jan 2013 17:23:26 +0000 (17:23 +0000)]
powerpc/pasemi: Fix crash on reboot
commit f96972f2dc "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"
added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.
When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.
One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.
Running a simple function trace, you can see it goes off quite a bit:
Li Zhong [Sun, 2 Dec 2012 20:19:22 +0000 (20:19 +0000)]
powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32
This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Torsten Kaiser [Sun, 20 Jan 2013 09:24:49 +0000 (10:24 +0100)]
xfs: Fix xfs_swap_extents() after removal of xfs_flushinval_pages()
Commit fb59581404ab7ec5075299065c22cb211a9262a9 removed
xfs_flushinval_pages() and changed its callers to use
filemap_write_and_wait() and truncate_pagecache_range() directly.
But in xfs_swap_extents() this change accidental switched the argument
for 'tip' to 'ip'. This patch switches it back to 'tip'
Signed-off-by: Torsten Kaiser <just.for.lkml@googlemail.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
Linus Torvalds [Mon, 28 Jan 2013 19:52:56 +0000 (11:52 -0800)]
Merge tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"One fix for the AMD IOMMU driver to work around broken BIOSes found in
the field. Some BIOSes forget to enable a workaround for a hardware
problem which might cause the IOMMU to stop working under high load
conditions. The fix makes sure this workaround is enabled."
* tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround
Linus Torvalds [Mon, 28 Jan 2013 19:51:57 +0000 (11:51 -0800)]
Merge tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
Pull networking updates from David Miller:
"Much more accumulated than I would have liked due to an unexpected
bout with a nasty flu:
1) AH and ESP input don't set ECN field correctly because the
transport head of the SKB isn't set correctly, fix from Li
RongQing.
2) If netfilter conntrack zones are disabled, we can return an
uninitialized variable instead of the proper error code. Fix from
Borislav Petkov.
3) Fix double SKB free in ath9k driver beacon handling, from Felix
Feitkau.
4) Remove bogus assumption about netns cleanup ordering in
nf_conntrack, from Pablo Neira Ayuso.
5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
Dumazet. It uses spin_is_locked() in it's test and is therefore
unsuitable for UP.
6) Fix SELINUX labelling regressions added by the tuntap multiqueue
changes, from Paul Moore.
7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
Nayak Sujir.
8) CXGB4 driver sets interrupt coalescing parameters only on first
queue, rather than all of them. Fix from Thadeu Lima de Souza
Cascardo.
9) Fix regression in the dispatch of read/write registers in dm9601
driver, from Tushar Behera.
10) ipv6_append_data miscalculates header length, from Romain KUNTZ.
11) Fix PMTU handling regressions on ipv4 routes, from Steffen
Klassert, Timo Teräs, and Julian Anastasov.
12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
expression. From Nickolai Zeldovich.
13) macvlan_get_size() causes underallocation netlink message space,
fix from Eric Dumazet.
14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
Zeldovich. Amusingly the zero check was already there, we were
just performing it after the modulus :-)
15) Some more splice bug fixes from Eric Dumazet, which fix things
mostly eminating from how we now more aggressively use high-order
pages in SKBs.
16) Fix size calculation bug when freeing hash tables in the IPSEC
xfrm code, from Michal Kubecek.
17) Fix PMTU event propagation into socket cached routes, from Steffen
Klassert.
18) Fix off by one in TX buffer release in netxen driver, from Eric
Dumazet.
19) Fix rediculous memory allocation requirements introduced by the
tuntap multiqueue changes, from Jason Wang.
20) Remove bogus AMD platform workaround in r8169 driver that causes
major problems in normal operation, from Timo Teräs.
21) virtio-net set affinity and select queue don't handle
discontiguous cpu numbers properly, fix from Wanlong Gao.
22) Fix a route refcounting issue in loopback driver, from Eric
Dumazet. There's a similar fix coming that we might add to the
macvlan driver as well.
23) Fix SKB leaks in batman-adv's distributed arp table code, from
Matthias Schiffer.
24) r8169 driver gives descriptor ownership back the hardware before
we're done reading the VLAN tag out of it, fix from Francois
Romieu.
25) Checksums not calculated properly in GRE tunnel driver fix from
Pravin B Shelar.
26) Fix SCTP memory leak on namespace exit."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
dm9601: support dm9620 variant
SCTP: Free the per-net sysctl table on net exit. v2
net: phy: icplus: fix broken INTR pin settings
net: phy: icplus: Use the RGMII interface mode to configure clock delays
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
sctp: set association state to established in dupcook_a handler
ip6mr: limit IPv6 MRT_TABLE identifiers
r8169: fix vlan tag read ordering.
net: cdc_ncm: use IAD provided by the USB core
batman-adv: filter ARP packets with invalid MAC addresses in DAT
batman-adv: check for more types of invalid IP addresses in DAT
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
net: loopback: fix a dst refcounting issue
virtio-net: reset virtqueue affinity when doing cpu hotplug
virtio-net: split out clean affinity function
virtio-net: fix the set affinity bug when CPU IDs are not consecutive
can: pch_can: fix invalid error codes
can: ti_hecc: fix invalid error codes
can: c_can: fix invalid error codes
r8169: remove the obsolete and incorrect AMD workaround
...
projects / karo-tx-linux.git / log