If we reenable ftrace via syctl, we currently set ftrace_trace_function
based on the previous simplistic algorithm. This is inconsistent with
what update_ftrace_function does. So better call that helper instead.
Link: http://lkml.kernel.org/r/5151D26F.1070702@siemens.com Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The sched_clock_remote() implementation has the following inatomicity
problem on 32bit systems when accessing the remote scd->clock, which
is a 64bit value.
While the update of scd->clock is using an atomic64 mechanism, the
readout on the remote cpu is not, which can cause completely bogus
readouts.
It is a quite rare problem, because it requires the update to hit the
narrow race window between the low/high readout and the update must go
across the 32bit boundary.
The resulting misbehaviour is, that CPU1 will see the sched_clock on
CPU1 ~4 seconds ahead of it's own and update CPU1s sched_clock value
to this bogus timestamp. This stays that way due to the clamping
implementation for about 4 seconds until the synchronization with
CLOCK_MONOTONIC undoes the problem.
The issue is hard to observe, because it might only result in a less
accurate SCHED_OTHER timeslicing behaviour. To create observable
damage on realtime scheduling classes, it is necessary that the bogus
update of CPU1 sched_clock happens in the context of an realtime
thread, which then gets charged 4 seconds of RT runtime, which results
in the RT throttler mechanism to trigger and prevent scheduling of RT
tasks for a little less than 4 seconds. So this is quite unlikely as
well.
The issue was quite hard to decode as the reproduction time is between
2 days and 3 weeks and intrusive tracing makes it less likely, but the
following trace recorded with trace_clock=global, which uses
sched_clock_local(), gave the final hint:
What happens is that CPU0 goes idle and invokes
sched_clock_idle_sleep_event() which invokes sched_clock_local() and
CPU1 runs a remote wakeup for CPU0 at the same time, which invokes
sched_remote_clock(). The time jump gets propagated to CPU0 via
sched_remote_clock() and stays stale on both cores for ~4 seconds.
There are only two other possibilities, which could cause a stale
sched clock:
1) ktime_get() which reads out CLOCK_MONOTONIC returns a sporadic
wrong value.
2) sched_clock() which reads the TSC returns a sporadic wrong value.
#1 can be excluded because sched_clock would continue to increase for
one jiffy and then go stale.
#2 can be excluded because it would not make the clock jump
forward. It would just result in a stale sched_clock for one jiffy.
After quite some brain twisting and finding the same pattern on other
traces, sched_clock_remote() remained the only place which could cause
such a problem and as explained above it's indeed racy on 32bit
systems.
So while on 64bit systems the readout is atomic, we need to verify the
remote readout on 32bit machines. We need to protect the local->clock
readout in sched_clock_remote() on 32bit as well because an NMI could
hit between the low and the high readout, call sched_clock_local() and
modify local->clock.
Thanks to Siegfried Wulsch for bearing with my debug requests and
going through the tedious tasks of running a bunch of reproducer
systems to generate the debug information which let me decode the
issue.
Reported-by: Siegfried Wulsch <Siegfried.Wulsch@rovema.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1304051544160.21884@ionos Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some versions of pHyp will perform the adjunct partition test before the
ANDCOND test. The result of this is that H_RESOURCE can be returned and
cause the BUG_ON condition to occur. The HPTE is not removed. So add a
check for H_RESOURCE, it is ok if this HPTE is not removed as
pSeries_lpar_hpte_remove is looking for an HPTE to remove and not a
specific HPTE to remove. So it is ok to just move on to the next slot
and try again.
Signed-off-by: Michael Wolf <mjw@linux.vnet.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes a NULL pointer dereference at boot on UP1500.
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The usb_control_msg() function expects __u16 types and performs
the endianness conversions by itself.
However, in three places, a conversion is performed before it is
handed over to usb_control_msg(), which leads to a double conversion
(= no conversion):
* snd_usb_nativeinstruments_boot_quirk()
* snd_nativeinstruments_control_get()
* snd_nativeinstruments_control_put()
Caught by sparse:
sound/usb/mixer_quirks.c:512:38: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:512:38: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:512:38: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:35: warning: incorrect type in argument 5 (different base types)
sound/usb/mixer_quirks.c:543:35: expected unsigned short [unsigned] [usertype] value
sound/usb/mixer_quirks.c:543:35: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:56: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:543:56: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:543:56: got restricted __le16 [usertype] <noident>
sound/usb/quirks.c:502:35: warning: incorrect type in argument 5 (different base types)
sound/usb/quirks.c:502:35: expected unsigned short [unsigned] [usertype] value
sound/usb/quirks.c:502:35: got restricted __le16 [usertype] <noident>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Acked-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put_noidle in such case.
In __hwspin_lock_request, module_put is also called before
return in pm_runtime_get_sync failed case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com> Signed-off-by: Li Fei <fei.li@intel.com>
[edit commit log] Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There is a quirk patch 5e5a4f5d5a08c9c504fe956391ac3dae2c66556d
"ata_piix: make DVD Drive recognisable on systems with Intel Sandybridge
chipsets(v2)" fixing the 4 ports IDE controller 32bit PIO mode.
We've hit a problem with DVD not recognized on Haswell Desktop platform which
includes Lynx Point 2-port SATA controller.
This quirk patch disables 32bit PIO on this controller in IDE mode.
v2: Change spelling error in statememnt pointed by Sergei Shtylyov.
v3: Change comment statememnt and spliting line over 80 characters pointed by
Libor Pechacek and also rebase the patch against 3.8-rc7 kernel.
Tested-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The above trace was triggered by
"dd if=/dev/zero of=/dev/sr0 bs=2048 count=32768"
It was previously working by accident, since another bug introduced
by 4dce8ba94c7 (libata: Use 'bool' return value for ata_id_XXX) caused
all drives to use maxsect=65535.
Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The function returns type of ATAPI drives so it should return integer value.
The commit 4dce8ba94c7 (libata: Use 'bool' return value for ata_id_XXX) since
v2.6.39 changed the type of return value from int to bool, the change would
cause all of the ATAPI class drives to be treated as TYPE_TAPE and the
max_sectors of the drives to be set to 65535 because of the commit f8d8e5799b7(libata: increase 128 KB / cmd limit for ATAPI tape drives), for the
function would return true for all ATAPI class drives and the TYPE_TAPE is
defined as 0x01.
Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Cc: users@rt2x00.serialmonkey.com Cc: netdev@vger.kernel.org Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
rfc4543(gcm(*)) code for GMAC assumes that assoc scatterlist always contains
only one segment and only makes use of this first segment. However ipsec passes
assoc with three segments when using 'extended sequence number' thus in this
case rfc4543(gcm(*)) fails to function correctly. Patch fixes this issue.
Reported-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com> Tested-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The current code makes the assumption that a cpu_base lock won't be
held if the CPU corresponding to that cpu_base is offline, which isn't
always true.
If a hrtimer is not queued, then it will not be migrated by
migrate_hrtimers() when a CPU is offlined. Therefore, the hrtimer's
cpu_base may still point to a CPU which has subsequently gone offline
if the timer wasn't enqueued at the time the CPU went down.
Normally this wouldn't be a problem, but a cpu_base's lock is blindly
reinitialized each time a CPU is brought up. If a CPU is brought
online during the period that another thread is performing a hrtimer
operation on a stale hrtimer, then the lock will be reinitialized
under its feet, and a SPIN_BUG() like the following will be observed:
<0>[ 28.082085] BUG: spinlock already unlocked on CPU#0, swapper/0/0
<0>[ 28.087078] lock: 0xc4780b40, value 0x0 .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
<4>[ 42.451150] [<c0014398>] (unwind_backtrace+0x0/0x120) from [<c0269220>] (do_raw_spin_unlock+0x44/0xdc)
<4>[ 42.460430] [<c0269220>] (do_raw_spin_unlock+0x44/0xdc) from [<c071b5bc>] (_raw_spin_unlock+0x8/0x30)
<4>[ 42.469632] [<c071b5bc>] (_raw_spin_unlock+0x8/0x30) from [<c00a9ce0>] (__hrtimer_start_range_ns+0x1e4/0x4f8)
<4>[ 42.479521] [<c00a9ce0>] (__hrtimer_start_range_ns+0x1e4/0x4f8) from [<c00aa014>] (hrtimer_start+0x20/0x28)
<4>[ 42.489247] [<c00aa014>] (hrtimer_start+0x20/0x28) from [<c00e6190>] (rcu_idle_enter_common+0x1ac/0x320)
<4>[ 42.498709] [<c00e6190>] (rcu_idle_enter_common+0x1ac/0x320) from [<c00e6440>] (rcu_idle_enter+0xa0/0xb8)
<4>[ 42.508259] [<c00e6440>] (rcu_idle_enter+0xa0/0xb8) from [<c000f268>] (cpu_idle+0x24/0xf0)
<4>[ 42.516503] [<c000f268>] (cpu_idle+0x24/0xf0) from [<c06ed3c0>] (rest_init+0x88/0xa0)
<4>[ 42.524319] [<c06ed3c0>] (rest_init+0x88/0xa0) from [<c0c00978>] (start_kernel+0x3d0/0x434)
As an example, this particular crash occurred when hrtimer_start() was
executed on CPU #0. The code locked the hrtimer's current cpu_base
corresponding to CPU #1. CPU #0 then tried to switch the hrtimer's
cpu_base to an optimal CPU which was online. In this case, it selected
the cpu_base corresponding to CPU #3.
Before it could proceed, CPU #1 came online and reinitialized the
spinlock corresponding to its cpu_base. Thus now CPU #0 held a lock
which was reinitialized. When CPU #0 finally ended up unlocking the
old cpu_base corresponding to CPU #1 so that it could switch to CPU
#3, we hit this SPIN_BUG() above while in switch_hrtimer_base().
CPU #0 CPU #1
---- ----
... <offline>
hrtimer_start()
lock_hrtimer_base(base #1)
... init_hrtimers_cpu()
switch_hrtimer_base() ...
... raw_spin_lock_init(&cpu_base->lock)
raw_spin_unlock(&cpu_base->lock) ...
<spin_bug>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
When switching to tty ports, some lifetime assumptions were changed.
Specifically, close can now be called before the final tty reference is
dropped as part of hangup at device disconnect. Even with the ftdi
private-data refcounting this means that the port private data can be
freed while a process is sleeping on modem-status changes and thus
cannot be relied on to detect disconnects when woken up.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In patch "HID: microsoft: fix invalid rdesc for 3k kbd" I fixed
support for MS 3k keyboards. However the added check using memcmp and
a compound statement breaks build on architectures where memcmp is a
macro with parameters.
hid-microsoft.c:51:18: error: macro "memcmp" passed 6 arguments, but takes just 3
On x86_64, memcmp is a function, so I did not see the error.
Now that netdev_rx_handler_unregister contains synchronize_net(), we need
to call it outside of bond->lock, cause it might sleep. Also, remove the
already unneded synchronize_net().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
skb->ip_summed should be CHECKSUM_UNNECESSARY when the driver reports that
checksums were correct and CHECKSUM_NONE in any other case. They're
currently placed vice versa, which breaks the forwarding scenario. Fix it
by placing them as described above.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 35d48903e97819 (bonding: fix rx_handler locking) added a race
in bonding driver, reported by Steven Rostedt who did a very good
diagnosis :
<quoting Steven>
I'm currently debugging a crash in an old 3.0-rt kernel that one of our
customers is seeing. The bug happens with a stress test that loads and
unloads the bonding module in a loop (I don't know all the details as
I'm not the one that is directly interacting with the customer). But the
bug looks to be something that may still be present and possibly present
in mainline too. It will just be much harder to trigger it in mainline.
In -rt, interrupts are threads, and can schedule in and out just like
any other thread. Note, mainline now supports interrupt threads so this
may be easily reproducible in mainline as well. I don't have the ability
to tell the customer to try mainline or other kernels, so my hands are
somewhat tied to what I can do.
But according to a core dump, I tracked down that the eth irq thread
crashed in bond_handle_frame() here:
slave = bond_slave_get_rcu(skb->dev);
bond = slave->bond; <--- BUG
the slave returned was NULL and accessing slave->bond caused a NULL
pointer dereference.
Which is basically:
dev->rx_handler = NULL;
dev->rx_handler_data = NULL;
And looking at __netif_receive_skb() we have:
rx_handler = rcu_dereference(skb->dev->rx_handler);
if (rx_handler) {
if (pt_prev) {
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = NULL;
}
switch (rx_handler(&skb)) {
My question to all of you is, what stops this interrupt from happening
while the bonding module is unloading? What happens if the interrupt
triggers and we have this:
What protection am I missing in the bond release handler that would
prevent the above from happening?
</quoting Steven>
We can fix bug this in two ways. First is adding a test in
bond_handle_frame() and others to check if rx_handler_data is NULL.
A second way is adding a synchronize_net() in
netdev_rx_handler_unregister() to make sure that a rcu protected reader
has the guarantee to see a non NULL rx_handler_data.
The second way is better as it avoids an extra test in fast path.
Reported-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jpirko@redhat.com> Cc: Paul E. McKenney <paulmck@us.ibm.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
According to the Datasheet (page 52):
15-12 Reserved
11-0 RXBC Receive Byte Count
This field indicates the present received frame byte size.
The code has a bug:
rxh = ks8851_rdreg32(ks, KS_RXFHSR);
rxstat = rxh & 0xffff;
rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied
Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Erik Hugne's errata proposal (Errata ID: 3480) to RFC4291 has been
verified: http://www.rfc-editor.org/errata_search.php?eid=3480
We have to check for pkt_type and loopback flag because either the
packets are allowed to travel over the loopback interface (in which case
pkt_type is PACKET_HOST and IFF_LOOPBACK flag is set) or they travel
over a non-loopback interface back to us (in which case PACKET_TYPE is
PACKET_LOOPBACK and IFF_LOOPBACK flag is not set).
Cc: Erik Hugne <erik.hugne@ericsson.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
v2:
a) moved before multicast source address check
b) changed comment to netdev style
Cc: Erik Hugne <erik.hugne@ericsson.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix bug for DM9000 revision B which contain a DSP PHY
DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().
Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.
Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Usage of pci-msi results in corrupted dma packet transfers to the host.
Reported-by: rebelyouth <rebelyouth.hacklab@gmail.com> Cc: Huang, Xiong <xiong@qca.qualcomm.com> Tested-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some network drivers use a non default hard_header_len
Transmitted skb should take into account dev->hard_header_len, or risk
crashes or expensive reallocations.
In the case of aoe, lets reserve MAX_HEADER bytes.
David reported a crash in defxx driver, solved by this patch.
Reported-by: David Oostdyk <daveo@ll.mit.edu> Tested-by: David Oostdyk <daveo@ll.mit.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ed Cashin <ecashin@coraid.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com> Suggested-by: Sriramakrishnan A G <srk@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If slave sysfs symlink failes to be created - we end up without removing
the master sysfs symlink. Remove it in case of failure.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As reported by Jan, and others over the past few years, there is a
race condition caused by unix_release setting the sock->sk pointer
to NULL before properly marking the socket as dead/orphaned. This
can cause a problem with the LSM hook security_unix_may_send() if
there is another socket attempting to write to this partially
released socket in between when sock->sk is set to NULL and it is
marked as dead/orphaned. This patch fixes this by only setting
sock->sk to NULL after the socket has been marked as dead; I also
take the opportunity to make unix_release_sock() a void function
as it only ever returned 0/success.
Dave, I think this one should go on the -stable pile.
Special thanks to Jan for coming up with a reproducer for this
problem.
Reported-by: Jan Stancek <jan.stancek@gmail.com> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
First I would give three observations which will be used later.
Observation 1: if (delayed_work_pending(wq)) cancel_delayed_work(wq)
This usage is wrong because the pending bit is cleared just before the
work's fn is executed and if the function re-arms itself we might end up
with the work still running. It's safe to call cancel_delayed_work_sync()
even if the work is not queued at all.
Observation 2: Use of INIT_DELAYED_WORK()
Work needs to be initialized only once prior to (de/en)queueing.
Observation 3: IFF_UP is set only after ndo_open is called
Related race conditions:
1. Race between bonding_store_miimon() and bonding_store_arp_interval()
Because of Obs.1 we can end up having both works enqueued.
2. Multiple races with INIT_DELAYED_WORK()
Since the works are not protected by anything between INIT_DELAYED_WORK()
and calls to (en/de)queue it is possible for races between the following
functions:
(races are also possible between the calls to INIT_DELAYED_WORK()
and workqueue code)
bonding_store_miimon() - bonding_store_arp_interval(), bond_close(),
bond_open(), enqueued functions
bonding_store_arp_interval() - bonding_store_miimon(), bond_close(),
bond_open(), enqueued functions
3. By Obs.1 we need to change bond_cancel_all()
Bugs 1 and 2 are fixed by moving all work initializations in bond_open
which by Obs. 2 and Obs. 3 and the fact that we make sure that all works
are cancelled in bond_close(), is guaranteed not to have any work
enqueued.
Also RTNL lock is now acquired in bonding_store_miimon/arp_interval so
they can't race with bond_close and bond_open. The opposing work is
cancelled only if the IFF_UP flag is set and it is cancelled
unconditionally. The opposing work is already cancelled if the interface
is down so no need to cancel it again. This way we don't need new
synchronizations for the bonding workqueue. These bugs (and fixes) are
tied together and belong in the same patch.
Note: I have left 1 line intentionally over 80 characters (84) because I
didn't like how it looks broken down. If you'd prefer it otherwise,
then simply break it.
v2: Make description text < 75 columns
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Masatake YAMATO <yamato@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
vlan_vid_del() could possibly free ->vlan_info after a RCU grace
period, however, we may still refer to the freed memory area
by 'grp' pointer. Found by code inspection.
This patch moves vlan_vid_del() as behind as possible.
Cc: Patrick McHardy <kaber@trash.net> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On SACK reneging the sender immediately retransmits and forces a
timeout but disables Eifel (undo). If the (buggy) receiver does not
drop any packet this can trigger a false slow-start retransmit storm
driven by the ACKs of the original packets. This can be detected with
undo and TCP timestamps.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A long standing problem with TSO is the fact that tcp_tso_should_defer()
rearms the deferred timer, while it should not.
Current code leads to following bad bursty behavior :
20:11:24.484333 IP A > B: . 297161:316921(19760) ack 1 win 119
20:11:24.484337 IP B > A: . ack 263721 win 1117
20:11:24.485086 IP B > A: . ack 265241 win 1117
20:11:24.485925 IP B > A: . ack 266761 win 1117
20:11:24.486759 IP B > A: . ack 268281 win 1117
20:11:24.487594 IP B > A: . ack 269801 win 1117
20:11:24.488430 IP B > A: . ack 271321 win 1117
20:11:24.489267 IP B > A: . ack 272841 win 1117
20:11:24.490104 IP B > A: . ack 274361 win 1117
20:11:24.490939 IP B > A: . ack 275881 win 1117
20:11:24.491775 IP B > A: . ack 277401 win 1117
20:11:24.491784 IP A > B: . 316921:332881(15960) ack 1 win 119
20:11:24.492620 IP B > A: . ack 278921 win 1117
20:11:24.493448 IP B > A: . ack 280441 win 1117
20:11:24.494286 IP B > A: . ack 281961 win 1117
20:11:24.495122 IP B > A: . ack 283481 win 1117
20:11:24.495958 IP B > A: . ack 285001 win 1117
20:11:24.496791 IP B > A: . ack 286521 win 1117
20:11:24.497628 IP B > A: . ack 288041 win 1117
20:11:24.498459 IP B > A: . ack 289561 win 1117
20:11:24.499296 IP B > A: . ack 291081 win 1117
20:11:24.500133 IP B > A: . ack 292601 win 1117
20:11:24.500970 IP B > A: . ack 294121 win 1117
20:11:24.501388 IP B > A: . ack 295641 win 1117
20:11:24.501398 IP A > B: . 332881:351881(19000) ack 1 win 119
While the expected behavior is more like :
20:19:49.259620 IP A > B: . 197601:202161(4560) ack 1 win 119
20:19:49.260446 IP B > A: . ack 154281 win 1212
20:19:49.261282 IP B > A: . ack 155801 win 1212
20:19:49.262125 IP B > A: . ack 157321 win 1212
20:19:49.262136 IP A > B: . 202161:206721(4560) ack 1 win 119
20:19:49.262958 IP B > A: . ack 158841 win 1212
20:19:49.263795 IP B > A: . ack 160361 win 1212
20:19:49.264628 IP B > A: . ack 161881 win 1212
20:19:49.264637 IP A > B: . 206721:211281(4560) ack 1 win 119
20:19:49.265465 IP B > A: . ack 163401 win 1212
20:19:49.265886 IP B > A: . ack 164921 win 1212
20:19:49.266722 IP B > A: . ack 166441 win 1212
20:19:49.266732 IP A > B: . 211281:215841(4560) ack 1 win 119
20:19:49.267559 IP B > A: . ack 167961 win 1212
20:19:49.268394 IP B > A: . ack 169481 win 1212
20:19:49.269232 IP B > A: . ack 171001 win 1212
20:19:49.269241 IP A > B: . 215841:221161(5320) ack 1 win 119
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Van Jacobson <vanj@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Nandita Dukkipati <nanditad@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.
Fix: We should increase the value to 8192/8
Signed-off-by: Mirko Lindner <mlindner@marvell.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.
Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The Receive Overflow interrupt is handled correctly
Signed-off-by: Mirko Lindner <mlindner@marvell.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".
But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:
[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
time we call loop_set_fd() we check that loop_device->lo_state is
Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
it will get EBUSY. And if we try to loop_clr_fd() on unbound loop
device we'll get ENXIO.
loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
loop_device->lo_ctl_mutex. ]
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
fs/nfs/nfs4proc.c: In function ‘__nfs4_get_acl_uncached’:
fs/nfs/nfs4proc.c:3811:14: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
fs/nfs/nfs4proc.c:3818:15: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
Introduced by commit bf118a34 "NFSv4: include bitmap in nfsv4 get
acl data", Dec 7, 2011.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For large UDF filesystems with 512-byte blocks the number of necessary
bitmap blocks is larger than 2^16 so s_nr_groups in udf_bitmap overflows
(the number will overflow for filesystems larger than 128 GB with
512-byte blocks). That results in ENOSPC errors despite the filesystem
has plenty of free space.
Fix the problem by changing s_nr_groups' type to 'int'. That is enough
even for filesystems 2^32 blocks (UDF maximum) and 512-byte blocksize.
Reported-and-tested-by: v10lator@myway.de Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[lxiang: Backported for 3.4-stable. Removed code of simultaneous AP and mesh
mode added in 4a5fc6d 3.9-rc1.] Signed-off-by: Lingzhu Xiang <lxiang@redhat.com> Reviewed-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: no debugfs support] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
find_vma() can be called by multiple threads with read lock
held on mm->mmap_sem and any of them can update mm->mmap_cache.
Prevent compiler from re-fetching mm->mmap_cache, because other
readers could update it in the meantime:
thread 1 thread 2
|
find_vma() | find_vma()
struct vm_area_struct *vma = NULL; |
vma = mm->mmap_cache; |
if (!(vma && vma->vm_end > addr |
&& vma->vm_start <= addr)) { |
| mm->mmap_cache = vma;
return vma; |
^^ compiler may optimize this |
local variable out and re-read |
mm->mmap_cache |
This issue can be reproduced with gcc-4.8.0-1 on s390x by running
mallocstress testcase from LTP, which triggers:
so eisa_probe will fail from pci_eisa_init
==>eisa_root_register
==>eisa_probe path.
as force_probe is not set in pci_eisa_root, it will bail early when
slot0 is not probed and initialized.
Try to use subsys_initcall_sync instead, and will keep following sequence:
pci_subsys_init
pci_eisa_init_early
pnpacpi_init/isapnp_init
After this patch EISA can be initialized properly, and PNP overlapping
resource will not be reserved.
[ 10.104434] system 00:0f: [io 0x0c80-0x0c84] could not be reserved
Reported-by: Matthew Whitehead <mwhitehe@redhat.com> Tested-by: Matthew Whitehead <mwhitehe@redhat.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some SPI slave devices require asserted chip select signal across
multiple transfer segments of an SPI message. Currently the driver
always de-asserts the internal SS signal for every single transfer
segment of the message and ignores the 'cs_change' flag of the
transfer description. Disable the internal chip select (SS) only
if this is needed and indicated by the 'cs_change' flag.
Without this change, each partial transfer of a surrounding
multi-part SPI transaction might erroneously change the SS
signal, which might prevent slaves from answering the request
that was sent in a previous transfer segment because the
transaction could be considered aborted (SS was de-asserted
before reading the response).
Reported-by: Gerhard Sittig <gerhard.sittig@ifm.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When multiple ovq operations are being performed (lots of open/close
operations on virtio_console fds), the __send_control_msg() function can
get confused without locking.
A simple recipe to cause badness is:
* create a QEMU VM with two virtio-serial ports
* in the guest, do
while true;do echo abc >/dev/vport0p1;done
while true;do echo edf >/dev/vport0p2;done
In one run, this caused a panic in __send_control_msg(). In another, I
got
virtio_console virtio0: control-o:id 0 is not a head!
This also results repeated messages similar to these on the host:
qemu-kvm: virtio-serial-bus: Unexpected port id 478762112 for device virtio-serial-bus.0
qemu-kvm: virtio-serial-bus: Unexpected port id 478762368 for device virtio-serial-bus.0
Reported-by: FuXiangChun <xfu@redhat.com> Signed-off-by: Amit Shah <amit.shah@redhat.com> Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com> Reviewed-by: Asias He <asias@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The cvq_lock was taken for the c_ivq. Rename the lock to make that
obvious.
We'll also add a lock around the c_ovq in the next commit, so there's no
ambiguity.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Reviewed-by: Asias He <asias@redhat.com> Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
[bwh: Backported to 3.2:
- Adjust context
- Drop change to virtcons_restore()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The current Tilera boot infrastructure now provides the initramfs
to Linux as a Tilera-hypervisor file named "initramfs", rather than
"initramfs.cpio.gz", as before. (This makes it reasonable to use
other compression techniques than gzip on the file without having to
worry about the name causing confusion.) Adapt to use the new name,
but also fall back to checking for the old name.
Cc'ing to stable so that older kernels will remain compatible with
newer Tilera boot infrastructure.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
After commit 21d8a15a (lookup_one_len: don't accept . and ..) reiserfs
started failing to delete xattrs from inode. This was due to a buggy
test for '.' and '..' in fill_with_dentries() which resulted in passing
'.' and '..' entries to lookup_one_len() in some cases. That returned
error and so we failed to iterate over all xattrs of and inode.
Fix the test in fill_with_dentries() along the lines of the one in
lookup_one_len().
Reported-by: Pawel Zawora <pzawora@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW
Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com> Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A user reported a problem where he was getting early ENOSPC with hundreds of
gigs of free data space and 6 gigs of free metadata space. This is because the
global block reserve was taking up the entire free metadata space. This is
ridiculous, we have infrastructure in place to throttle if we start using too
much of the global reserve, so instead of letting it get this huge just limit it
to 512mb so that users can still get work done. This allowed the user to
complete his rsync without issues. Thanks
Reported-and-tested-by: Stefan Priebe <s.priebe@profihost.ag> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.
Signed-off-by: Kees Cook <keescook@chromium.org> Reported-by: Oded Horovitz <oded@privatecore.com> Reported-by: Brad Spengler <spender@grsecurity.net> Cc: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.
This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.
Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.
Tested-by: Chris Vine <chris@cvine.freeserve.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Thias patch fixes a define conflict between the SH architecture and the sja1000
driver:
drivers/net/can/sja1000/sja1000.h:59:0: warning:
"REG_SR" redefined [enabled by default]
arch/sh/include/asm/ptrace_32.h:25:0: note:
this is the location of the previous definition
A SJA1000_ prefix is added to the offending sja1000 define only, to make a
minimal patch suited for stable. A later patch will add a SJA1000_ prefix to
all defines in sja1000.h.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There is a bug introduced with commit 27c2127 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.
Reported-by: Andreas Degert <andreas.degert@googlemail.com> Signed-off-by: Joerg Roedel <joro@8bytes.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
vcs_poll_data_free() calls unregister_vt_notifier(), which calls
atomic_notifier_chain_unregister(), which calls synchronize_rcu().
Do it *after* we'd dropped ->f_lock.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
... lest we get livelocks between path_is_under() and d_path() and friends.
The thing is, wrt fairness lglocks are more similar to rwsems than to rwlocks;
it is possible to have thread B spin on attempt to take lock shared while thread
A is already holding it shared, if B is on lower-numbered CPU than A and there's
a thread C spinning on attempt to take the same lock exclusive.
As the result, we need consistent ordering between vfsmount_lock (lglock) and
rename_lock (seq_lock), even though everything that takes both is going to take
vfsmount_lock only shared.
Spotted-by: Brad Spengler <spender@grsecurity.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2:
- Adjust context
- s/&vfsmount_lock/vfsmount_lock/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since we only enforce an upper bound, not a lower bound, a "negative"
length can get through here.
The symptom seen was a warning when we attempt to a kmalloc with an
excessive size.
Reported-by: Toralf Förster <toralf.foerster@gmx.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For the s626 driver, there is a bug in the handling of asynchronous
commands on the AI subdevice when the stop source is `TRIG_NONE`. The
command should run continuously until cancelled, but the interrupt
handler stops the command running after the first scan.
The command set-up function `s626_ai_cmd()` contains this code:
switch (cmd->stop_src) {
case TRIG_COUNT:
/* data arrives as one packet */
devpriv->ai_sample_count = cmd->stop_arg;
devpriv->ai_continous = 0;
break;
case TRIG_NONE:
/* continous acquisition */
devpriv->ai_continous = 1;
devpriv->ai_sample_count = 0;
break;
}
The interrupt handler `s626_irq_handler()` contains this code:
if (!(devpriv->ai_continous))
devpriv->ai_sample_count--;
if (devpriv->ai_sample_count <= 0) {
devpriv->ai_cmd_running = 0;
/* ... */
}
So `devpriv->ai_sample_count` is only decremented for the `TRIG_COUNT`
case, but `devpriv->ai_cmd_running` is set to 0 (and the command
stopped) regardless.
Fix this in `s626_ai_cmd()` by setting `devpriv->ai_sample_count = 1`
for the `TRIG_NONE` case. The interrupt handler will not decrement it
so it will remain greater than 0 and the check for stopping the
acquisition will fail.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Use proper macro while extracting TRB transfer length from
Transfer event TRBs. Adding a macro EVENT_TRB_LEN (bits 0:23)
for the same, and use it instead of TRB_LEN (bits 0:16) in
case of event TRBs.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit b10de142119a676552df3f0d2e3a9d647036c26a "USB: xhci:
Bulk transfer support". This patch will have issues applying to older
kernels.
Signed-off-by: Vivek gautam <gautam.vivek@samsung.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We need to be careful when testing task->tk_waitqueue in
rpc_wake_up_task_queue_locked, because it can be changed while we
are holding the queue->lock.
By adding appropriate memory barriers, we can ensure that it is safe to
test task->tk_waitqueue for equality if the RPC_TASK_QUEUED bit is set.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit f0dc117abdfa ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.
The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.
This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq(). If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.
This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.
Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The dma-sh7760 currently fails with the following compile error:
sound/soc/sh/dma-sh7760.c:346:2: error: unknown field 'pcm_ops' specified in initializer
sound/soc/sh/dma-sh7760.c:346:2: warning: initialization from incompatible pointer type
sound/soc/sh/dma-sh7760.c:347:2: error: unknown field 'pcm_new' specified in initializer
sound/soc/sh/dma-sh7760.c:347:2: warning: initialization makes integer from pointer without a cast
sound/soc/sh/dma-sh7760.c:348:2: error: unknown field 'pcm_free' specified in initializer
sound/soc/sh/dma-sh7760.c:348:2: warning: initialization from incompatible pointer type
sound/soc/sh/dma-sh7760.c: In function 'sh7760_soc_platform_probe':
sound/soc/sh/dma-sh7760.c:353:2: warning: passing argument 2 of 'snd_soc_register_platform' from incompatible pointer type
include/sound/soc.h:368:5: note: expected 'struct snd_soc_platform_driver *' but argument is of type 'struct snd_soc_platform *'
This is due the misnaming of the snd_soc_platform_driver type name and 'ops'
field. The issue was introduced in commit f0fba2a("ASoC: multi-component - ASoC
Multi-Component Support").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We need to clear the NFS_LSEG_LAYOUTCOMMIT bits atomically with the
NFS_INO_LAYOUTCOMMIT bit, otherwise we may end up with situations
where the two are out of sync.
The first half of the problem is to ensure that pnfs_layoutcommit_inode
clears the NFS_LSEG_LAYOUTCOMMIT bit through pnfs_list_write_lseg.
We still need to keep the reference to those segments until the RPC call
is finished, so in order to make it clear _where_ those references come
from, we add a helper pnfs_list_write_lseg_done() that cleans up after
pnfs_list_write_lseg.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Acked-by: Benny Halevy <bhalevy@tonian.com>
[bwh: Backported to 3.2: s/pnfs_put_lseg/put_lseg/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
when pnfs block using device mapper,if umounting later,it maybe
cause oops. we apply "1 + sizeof(bl_umount_request)" memory for
msg->data, the memory maybe overflow when we do "memcpy(&dataptr
[sizeof(bl_msg)], &bl_umount_request, sizeof(bl_umount_request))",
because the size of bl_msg is more than 1 byte.
Signed-off-by: fanchaoting<fanchaoting@cn.fujitsu.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[bwh: Backported to 3.2:
- In dev_remove(), msg is a structure not a pointer to it] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In case of 'if (filp->f_pos == 0 or 1)' of sysfs_readdir(),
the failure from filldir() isn't handled, and the reference counter
of the sysfs_dirent object pointed by filp->private_data will be
released without clearing filp->private_data, so use after free
bug will be triggered later.
This patch returns immeadiately under the situation for fixing the bug,
and it is reasonable to return from readdir() when filldir() fails.
Reported-by: Dave Jones <davej@redhat.com> Tested-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While readdir() is running, lseek() may set filp->f_pos as zero,
then may leave filp->private_data pointing to one sysfs_dirent
object without holding its reference counter, so the sysfs_dirent
object may be used after free in next readdir().
This patch holds inode->i_mutex to avoid the problem since
the lock is always held in readdir path.
Reported-by: Dave Jones <davej@redhat.com> Tested-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: open-code file_inode() which we don't have] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This makes sure that release_sock is called for all error conditions in
irda_getsockopt.
Signed-off-by: Kees Cook <keescook@chromium.org> Reported-by: Brad Spengler <spender@grsecurity.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 7708992 ("xen/blkback: Seperate the bio allocation and the bio
submission") consolidated the pendcnt updates to just a single write,
neglecting the fact that the error path relied on it getting set to 1
up front (such that the decrement in __end_block_io_op() would actually
drop the count to zero, triggering the necessary cleanup actions).
Also remove a misleading and a stale (after said commit) comment.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The commit 'ath9k_hw: fix calibration issues on chainmask that don't
include chain 0' changed the hardware chainmask to the chip chainmask
for the duration of the calibration, but the revert to user
configuration in the reset path runs too early.
That causes some issues with limiting the number of antennas (including
spurious failure in hardware-generated packets).
Fix this by reverting the chainmask after the essential parts of the
calibration that need the workaround, and before NF calibration is run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>