Aaro Koskinen [Sat, 1 Jun 2013 18:42:58 +0000 (21:42 +0300)]
staging: MIPS: add Octeon USB HCD support
Add support for Octeon USB HCD. Tested on EdgeRouter Lite with USB
mass storage.
The driver has been extracted from GPL sources of EdgeRouter Lite firmware
(based on Linux 2.6.32.13). Some minor fixes and cleanups have been done
to make it work with 3.10-rc3.
$ uname -a
Linux (none) 3.10.0-rc3-edge-00005-g86cb5bc #41 SMP PREEMPT Sat Jun 1 20:41:46 EEST 2013 mips64 GNU/Linux
$ modprobe octeon-usb
[ 37.971683] octeon_usb: module is from the staging directory, the quality is unknown, you have been warned.
[ 37.983649] OcteonUSB: Detected 1 ports
[ 37.999360] OcteonUSB OcteonUSB.0: Octeon Host Controller
[ 38.004847] OcteonUSB OcteonUSB.0: new USB bus registered, assigned bus number 1
[ 38.012332] OcteonUSB OcteonUSB.0: irq 122, io mem 0x00000000
[ 38.019970] hub 1-0:1.0: USB hub found
[ 38.023851] hub 1-0:1.0: 1 port detected
[ 38.028101] OcteonUSB: Registered HCD for port 0 on irq 122
[ 38.391443] usb 1-1: new high-speed USB device number 2 using OcteonUSB
[ 38.586922] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 38.597375] scsi0 : usb-storage 1-1:1.0
[ 39.604111] scsi 0:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4
[ 39.619113] sd 0:0:0:0: [sda] 7579008 512-byte logical blocks: (3.88 GB/3.61 GiB)
[ 39.630696] sd 0:0:0:0: [sda] Write Protect is off
[ 39.635945] sd 0:0:0:0: [sda] No Caching mode page present
[ 39.641464] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 39.651341] sd 0:0:0:0: [sda] No Caching mode page present
[ 39.656917] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 39.664296] sda: sda1 sda2
[ 39.675574] sd 0:0:0:0: [sda] No Caching mode page present
[ 39.681093] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 39.687223] sd 0:0:0:0: [sda] Attached SCSI removable disk
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Daney <ddaney.cavm@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Harsh Kumar [Fri, 31 May 2013 15:30:42 +0000 (21:00 +0530)]
Staging: winbond: Check for unsuccessful allocation immediately
Check to see if allocation by kzalloc() or usb_alloc_urb() was unsuccessful
immediately after the allocation. Exit from the function can be right at that
point in case of allocation failure.
This avoids unnecessary use of usb_alloc_urb() & usb_free_urb() if kzalloc()
returns NULL.
Also, makes the code better structured & easier to understand.
Dan Carpenter [Thu, 30 May 2013 08:00:34 +0000 (11:00 +0300)]
Staging: crystalhd: remove an unneeded NULL check
We already established earlier in the function that "temp" is
non-NULL. We also don't need to set to NULL because it's a stack
variable an we return immediately.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: rts5139: Use correct USB transfer interval to fix syslog spamming
Using correct transfer interval as specified by the USB endpoint
when doing the interrupt transfer fixes the warning printed by
xhci USB core on every transfer that resulted in spamming
"xhci_queue_intr_tx: 74 callbacks suppressed" to syslog
every 5 seconds.
Signed-off-by: Marcus Overhagen <marcus.overhagen@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: rts5139: Fix SD card detection on Samsung NP730U3E Ultrabook
The timeout detection implemented in this driver isn't very
robust. Although the USB interrupt transfer was successful,
the polling thread often reported timeouts because the 50ms
had expired before it got scheduled, and the SD card wasn't
detected. Increasing it to 100ms, as used in other places of
this driver, makes it work.
Signed-off-by: Marcus Overhagen <marcus.overhagen@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wei Yongjun [Mon, 3 Jun 2013 02:08:13 +0000 (10:08 +0800)]
staging/lustre: fix return value check in libcfs_sock_ioctl()
In case of error, the function sock_alloc_file() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Peng Tao [Mon, 3 Jun 2013 13:58:18 +0000 (21:58 +0800)]
staging/lustre: silence gcc build warning
got bellow build warning that is indeed a false alarm.
CC [M] drivers/staging/lustre/lustre/llite/llite_nfs.o
drivers/staging/lustre/lustre/libcfs/nidstrings.c: In function ‘
libcfs_str2net_internal’:
drivers/staging/lustre/lustre/libcfs/nidstrings.c:432:17: warning: ‘nf’ may be
used uninitialized in this function [-Wuninitializ
ed]
Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hongchao Zhang [Mon, 3 Jun 2013 13:41:00 +0000 (21:41 +0800)]
staging/lustre/osc: check ostid if no OBD_CONNECT_FID
in lustre_set_wire_obdo, if "ocd->ocd_connect_flags" doesn't contain
OBD_CONNECT_FID, use "ost_id" to check the type of the object
instead of using ost_id.oi_fid only.
Jian Yu [Mon, 3 Jun 2013 13:40:59 +0000 (21:40 +0800)]
staging/lustre/tests: check nr_local in ofd_preprw()
This patch checks the number of bulk I/O RPC pages with
PTLRPC_MAX_BRW_PAGES in ofd_preprw() to avoid
LASSERT(iobuf->dr_npages < iobuf->dr_max_pages) occurring
while larger I/O size is specified.
The patch also fixes echo_client_prep_commit() to reuse
the env context so as to avoid LASSERT(info->fti_exp == NULL)
occurring while the bulk I/O size is larger than
PTLRPC_MAX_BRW_SIZE.
The patch also improves obdfilter-survey to handle the
case while interoprating with old server.
[picked echo client part for upstream kernel submission]
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-2598
Lustre-change: http://review.whamcloud.com/6394 Signed-off-by: Jian Yu <jian.yu@intel.com> Reviewed-by: Alex Zhuravlev <alexey.zhuravlev@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always build 64bit ino internally except the client is mounted
with "32bitapi" option, so client will always use 64bit ino
internally. It will build 32bit ino, only if application requires
32 bit ino.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3318
Lustre-change: http://review.whamcloud.com/6371 Signed-off-by: wang di <di.wang@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Ned Bass <bass6@llnl.gov> Reviewed-by: Fan Yong <fan.yong@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emoly Liu [Mon, 3 Jun 2013 13:40:55 +0000 (21:40 +0800)]
staging/lustre/mdt: set ATTR_xTIME_SET to make atime update properly
To make atime update properly between 1.8 client and 2.x server,
this patch includes the following fixes:
- if MDS_ATTR_xTIME is set without MDS_ATTR_xTIME_SET and the client
does not have OBD_CONNECT_FULL20, convert it to LA_xTIME in
mdt_setattr_unpack().
- set both MDS_ATTR_xTIME | MDS_ATTR_xTIME_SET for timestamps in
ll_prepare_close(). This allows us to fix the server-side timestamp
setting in the future.
- remove attr_unpack() and convert the flags from MDS_ATTR_ to LA_*
directly in mdt_attr_valid_xlate() instead.
- improve sanityn.sh test_23().
[picked llite part for upstream kernel submission]
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3036
Lustre-change: http://review.whamcloud.com/6327 Signed-off-by: Liu Ying <emoly.liu@intel.com> Reviewed-by: Fan Yong <fan.yong@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the CL_LAYOUT comment, since it is possible that layout swap
could be used in cases where the file content is changed. I don't
think there are any real world use cases for this, but that depends
on what tools are being used on the filesystem.
Also change the "LAYOUT" string for this ChangeLog record type to
be "LYOUT" to match the convention of other strings to only be
5 characters long.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3279
Lustre-change: http://review.whamcloud.com/6338 Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging/lustre/ost: Ensure dirty flushed on fiemap ioctl
Data corruption is possible if cp(coreutils) uses FIEMAP to obtain
data holes in shared file, since there could be dirty cache on
other clients which hasn't been flushed back.
To ensure all the dirty on remote clients being flushed back on
fiemap ioctl, we'd acquire ldlm lock on server side for fiemap,
unless the local client (which invoke fiemap) has cached lock.
[picked osc part for upstream kernel submission]
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3219
Xyratex-bug-id: MRP-1001
Lustre-change: http://review.whamcloud.com/6127 Signed-off-by: Artem Blagodarenko <artem_blagodarenko@xyratex.com> Signed-off-by: Niu Yawei <yawei.niu@intel.com> Reviewed-by: Nathaniel Clark <nathaniel.l.clark@intel.com> Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Dilger [Mon, 3 Jun 2013 13:40:52 +0000 (21:40 +0800)]
staging/lustre/changelog: fix CL_LAYOUT, accept all types
In order to avoid compatibility issues with older ChangeLog consumers,
change the new CL_LAYOUT record to use the value previously assigned
to CL_IOCTL. The CL_IOCTL type was never used anywhere, and it didn't
really make any sense as a ChangeLog record, since it could really
mean anything at all.
The changelog_show_cb() function is renamed to changelog_kkuc_cb(),
since it is really about consuming the ChangeLog and passing it up to
the kernel-user-coms interface. At some point we should consider to
implement a DBUS-based ChangeLog interface as well.
The changelog_kkuc_cb() "sanity check" on cr_type was removed, since
there is no reason the client kernel needs to know every record type
that is being passed to userspace. It is up to the client tool to
determine what records that it can process.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3279
Lustre-change: http://review.whamcloud.com/6308 Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Bobi Jam <bobijam@gmail.com> Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com> Reviewed-by: Mike Pershin <mike.pershin@intel.com> Reviewed-by: Aurelien Degremont <aurelien.degremont@cea.fr> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John L. Hammond [Mon, 3 Jun 2013 13:40:51 +0000 (21:40 +0800)]
staging/lustre/lprocfs: use stats counter index for *pos
In lprocfs_stats_seq_{start,next,show,stop}() encode the counter index
(rather than the counter address) into *pos. Doing so simplifies these
functions and fixes a bug in the case of per-CPU stats where no stats
would be displayed at all if no events had yet occurred on CPU 0.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-2979
Lustre-change: http://review.whamcloud.com/6328 Signed-off-by: John L. Hammond <john.hammond@intel.com> Reviewed-by: wangdi <di.wang@intel.com> Reviewed-by: Bobi Jam <bobijam@gmail.com> Reviewed-by: Emoly Liu <emoly.liu@intel.com> Reviewed-by: Keith Mannthey <keith.mannthey@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wang di [Mon, 3 Jun 2013 13:40:50 +0000 (21:40 +0800)]
staging/lustre/ost: check pre 2.4 echo client in obdo validation
Because old echo client still uses o_id/o_seq for objid,
but new echo client will uses FID for the objid. Add
OBD_CONNECT_FID for 2.4 echo client, so 2.4 OST will
convert o_id/o_seq to FID if the request from old echo
client.
Add local flag OBD_FL_OSTID for o_flags to indicate
OST does not support FID yet, then echo client will
still send o_id/o_seq to OST.
cleanup ost_validate_obdo
[picked client part for upstream kernel submission]
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3187
Lustre-change: http://review.whamcloud.com/6287 Signed-off-by: wang di <di.wang@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Mike Pershin <mike.pershin@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wang di [Mon, 3 Jun 2013 13:40:49 +0000 (21:40 +0800)]
staging/lustre/llog: Do not use ostid swab for llogid
Since logid still use id/seq format in the request,
it will be swabbed by its own swab func, instead of
using ostid swab, which might see logid as FID incorrectly.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3302
Lustre-change: http://review.whamcloud.com/6305 Signed-off-by: wang di <di.wang@intel.com> Reviewed-by: John Hammond <johnlockwoodhammond@gmail.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikhail Pershin [Mon, 3 Jun 2013 13:40:48 +0000 (21:40 +0800)]
staging/lustre/obdclass: use common way to store lastid
Local files last id are stored in root in files named seq-xxx-lastid
while lastid for OST objects is stored in O/seq/LAST_ID special
object with zero OID and handled by OSD.
Patch reworks local files lastid to be stored in O/seq/LAST_ID too
and using the same format.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-2886
Lustre-change: http://review.whamcloud.com/6199 Signed-off-by: Mikhail Pershin <mike.pershin@intel.com> Signed-off-by: James Nunez <james.a.nunez@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Alex Zhuravlev <alexey.zhuravlev@intel.com> Reviewed-by: Fan Yong <fan.yong@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Dilger [Mon, 3 Jun 2013 13:40:47 +0000 (21:40 +0800)]
staging/lustre/lov: only dump header in lsm_lmm_verify
If lsm_lmm_verify_*() find an error in the lov_mds_md header
structure, don't dump the full stripe information, since this
can be totally bogus (e.g. if stripe_count == -1 or similar).
Instead, just dump the header information for debugging.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3271
Lustre-change: http://review.whamcloud.com/6261 Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Bob Glossman <bob.glossman@intel.com> Reviewed-by: John Hammond <johnlockwoodhammond@gmail.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bobi Jam [Mon, 3 Jun 2013 13:40:45 +0000 (21:40 +0800)]
staging/lustre/osc: some cleanup to reduce stack overflow chance
ptlrpcd_add_req() will wake_up other process, do not hold a spinlock
before calling ptlrpcd_queue_work()->ptlrpcd_add_req().
If current process is allocating memory, memory shrinker could get to
osc_lru_del(), don't call osc_lru_shrink() further since it could
lead a long calling chain.
Use static string OES_STRINGS in OSC_EXTENT_DUMP() to reduce stack
footprint.
Alloc crattr on heap for osc_build_rpc() to reduce stack footprint.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3281
Lustre-change: http://review.whamcloud.com/6270 Signed-off-by: Bobi Jam <bobijam.xu@intel.com> Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com> Reviewed-by: Keith Mannthey <keith.mannthey@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JC Lafoucriere [Mon, 3 Jun 2013 13:40:44 +0000 (21:40 +0800)]
staging/lustre/ldlm: suppress useless lock RPC for layout
In ldlm_lock_decref_internal() when l_lvb_data is freed to
reduce memory consumption, LDLM_FL_LVB_READY is not
cleared, so later when the lock is reused lvb is not
updated. But clearing LDLM_FL_LVB_READY forces layout refetch
at each file access, so the better is to remove the optimization.
The use case is after a restore in HSM.
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3280
Lustre-change: http://review.whamcloud.com/6268 Signed-off-by: JC Lafoucriere <jacques-charles.lafoucriere@cea.fr> Reviewed-by: Fan Yong <fan.yong@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleg Drokin [Mon, 3 Jun 2013 13:40:43 +0000 (21:40 +0800)]
staging/lustre: Revert "LU-2139 osc: Track and limit "unstable" pages"
This seems to be causing multiple issues: LU-3274, LU-3277
[The original commit is folded in the large Lusre patch. So we don't
have an exact commit to revert for kernel client -- Peng Tao] Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quiet a number of overly noisy and unhelpful console error
messages. Improve the format of other nearby errors.
In the case of {lod,lov}_fix_desc_stripe_size(), this doesn't
even need a console message unless it is actually changing
some stripe size that is below the minimum. Typically it is
only zero and is being bumped up to the default value.
[picked lov part for upstream kernel submission]
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-1095
Lustre-change: http://review.whamcloud.com/6264 Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Bobi Jam <bobijam@gmail.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wang di [Mon, 3 Jun 2013 13:40:41 +0000 (21:40 +0800)]
staging/lustre/utils: missing setting echo seq for getattr/setattr
It should set echo seq before do echo getattr/setattr, otherwise
echo_client will regard it as the object with MDT0 sequence.
[picked echo client part for upstream kernel submission]
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3267
Lustre-change: http://review.whamcloud.com/6263 Signed-off-by: wang di <di.wang@intel.com> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Reviewed-by: Lai Siyao <lai.siyao@intel.com> Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wang di [Mon, 3 Jun 2013 13:40:39 +0000 (21:40 +0800)]
staging/lustre/ofd: refill env in ofd_get_info
Because ofd_get_info(KEY_FIEMAP) might be called from
ptlrpc_server_handle_req_in(see the stack below),
where env might not be initialized correctly(see LBUG below),
so it refill refill in ofd_get_info.
This is a patch to the bh.c file that fixes up all indentation errors
found the checkpatch.pl tool. Two lines beyond 80 characters are left
alone to improve readability
Signed-off-by: Davis Abubakr-Sadik Nii Nai <dwa2pac@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xenia Ragiadakou [Sun, 26 May 2013 19:42:44 +0000 (22:42 +0300)]
rtl8192u: fix printk calls in r8192U_core.c
This patch replaces calls to printk with their
corresponding calls to pr_<loglevel>(fmt, ...)
and netdev_<loglevel>(dev, fmt, ...), when it
is applicable, to make the log messages more
informative.
Also, it fixes some small typos and whitespaces
found in log messages.
Markus Niebel [Mon, 27 May 2013 08:19:09 +0000 (10:19 +0200)]
staging: drm/imx: set correct sync pins for display
partial fix of changes from
"staging: drm/imx: Add support for VGA via TVE on i.MX53"
Have to call imx_drm_crtc_panel_format_pins in imx_drm_crtc_panel_format
with the correct pins instead of (0, 0) This enables configuration of
correct waveforms for vsync / hsync for parallel display, LDB (i.MX53 and
i.MX6) as well as HDMI and MIPI (i.MX6)
TODO: configure pins via device tree
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Harsh Kumar [Thu, 30 May 2013 05:48:12 +0000 (11:18 +0530)]
Staging: winbond: Made local functions static
Few functions are used only in one file. They are not included in any
other .h or .c files (I used grep to check). They seem to be local functions.
So, I have made them static.
I have also inlined one function as it is a one line function.
Peng Tao [Wed, 29 May 2013 13:40:56 +0000 (21:40 +0800)]
staging/lustre: fix LBUG and inode refcount bug
ldlm_proc_setup and ldlm_proc_cleanup should reset global
pde pointers otherwise remount may hit
LASSERT(ldlm_ns_proc_dir == NULL);
Also in libcfs_sock_ioctl, fput() includes itself sock_release.
So don't call sock_release twice otherwise kernel may oops
due to incorrect inode ref counting.
Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peng Tao [Wed, 29 May 2013 13:40:55 +0000 (21:40 +0800)]
staging/lustre: adapt proc_dir_entry change
In 3.10 merge window, proc_dir_entry is now private to proc. However,
Lustre lprocfs depends heavily on it and its now-gone read_proc_t and
write_proc_t members.
The patch largely changed the fact, and made lprocfs depend on none of
proc_dir_entry private members. All lprocfs callers are converted to
use the new seq_file scheme.
Also lprocfs_srch is removed so that we can drop lprocfs_lock. All callers
are changed to save created pde in proper place.
See https://jira.hpdd.intel.com/browse/LU-3319 for more details.
Signed-off-by: Peng Tao <tao.peng@emc.com> Signed-off-by: Andreas Dilger <andreas.dilger@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Wed, 29 May 2013 06:57:36 +0000 (09:57 +0300)]
Staging: rtl8192e: printing the wrong array
Smatch complained that there is an array overflow here. It looks
like we are supposed to be printing the ->rates_ex[] array which is
slightly larger than the ->rates[] array. This is a cut and paste
error.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wei Yongjun [Thu, 23 May 2013 09:28:05 +0000 (17:28 +0800)]
Staging: vt6655: add missing free_netdev() on error in hostap_enable_hostapd()
Add the missing free_netdev() before return from function
hostap_enable_hostapd() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log