Jean Delvare [Sun, 7 Oct 2012 22:26:16 +0000 (09:26 +1100)]
i2c-i801: Let i2c-mux-gpio find the GPIO chip
Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.
Jean Delvare [Sun, 7 Oct 2012 22:26:16 +0000 (09:26 +1100)]
i2c-mux-gpio: Add support for dynamically allocated GPIO pins
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.
In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.
The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
only. If finding the GPIO chip is the caller's responsibility, then
deferred probing (if the GPIO chip isn't there yet) will not only
affect the mux and the I2C bus segments behind it, but also the I2C
bus trunk.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Maxime Ripard [Sun, 7 Oct 2012 22:26:15 +0000 (09:26 +1100)]
i2c-mux-gpio: Use devm_kzalloc instead of kzalloc
Use the devm_kzalloc managed function to stripdown the error and remove
code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 7 Oct 2012 22:26:15 +0000 (09:26 +1100)]
i2c-i801: Support SMBus multiplexing on Asus Z8 series
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.
On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.
The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.
Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.
At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Peter Huewe [Sun, 7 Oct 2012 22:26:14 +0000 (09:26 +1100)]
i2c: Make I2C available on UML
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.
The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.
[JD: Some adjustments.]
[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Shubhrajyoti D [Sun, 7 Oct 2012 22:26:13 +0000 (09:26 +1100)]
i2c: Convert struct i2c_msg initialization to C99 format
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Julia Lawall [Sun, 7 Oct 2012 22:26:13 +0000 (09:26 +1100)]
i2c-smbus: Convert kzalloc to devm_kzalloc
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq. This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 7 Oct 2012 22:26:13 +0000 (09:26 +1100)]
i2c-mux: Add support for device auto-detection
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.
I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: David Daney <david.daney@cavium.com> Cc: Michael Lawnick <ml.lawnick@gmx.de> Cc: Rodolfo Giometti <giometti@linux.it>
Linus Torvalds [Sun, 7 Oct 2012 22:14:06 +0000 (07:14 +0900)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pul ACPI & Power Management updates from Len Brown:
- acpidump utility added
- intel_idle driver now supports IVB Xeon
- turbostat utility can now count SMIs
- ACPI can now bind to USB3 hubs
- misc fixes
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (49 commits)
ACPI: Add new sysfs interface to export device description
ACPI: Harden acpi_table_parse_entries() against BIOS bug
tools/power/turbostat: add option to count SMIs, re-name some options
tools/power turbostat: add [-d MSR#][-D MSR#] options to print counter deltas
intel_idle: enable IVB Xeon support
tools/power turbostat: add [-m MSR#] option
tools/power turbostat: make -M output pretty
tools/power turbostat: print more turbo-limit information
tools/power turbostat: delete unused line
tools/power turbostat: run on IVB Xeon
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
ACPI: run _OSC after ACPI_FULL_INITIALIZATION
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
tools/power/acpi/acpidump: version 20071116
tools/power/acpi/acpidump: version 20070714
tools/power/acpi/acpidump: version 20060606
tools/power/acpi/acpidump: version 20051111
xo15-ebook: convert to module_acpi_driver()
...
Ulf Hansson [Fri, 5 Oct 2012 16:45:39 +0000 (12:45 -0400)]
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
This patch fixes up the broken suspend sequence for eMMC with sleep
support. Additionally it reworks the eMMC4.5 Power Off Notification
feature so it fits together with the existing sleep feature.
The CMD0 based re-initialization of the eMMC at resume is re-introduced
to maintain compatiblity for devices using sleep.
A host shall use MMC_CAP2_POWEROFF_NOTIFY to enable the Power Off
Notification feature. We might be able to remove this cap later on,
if we think that Power Off Notification always is preferred over
sleep, even if the host is not able to cut the eMMC VCCQ power.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Saugata Das <saugata.das@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
clk_{un}prepare is mandatory for platforms using common clock framework.
Since this driver is used by SPEAr platform, which supports common clock
framework, add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Chris Ball [Wed, 19 Sep 2012 14:27:04 +0000 (22:27 +0800)]
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
Before this patch, we were using MMC_CAP2_BROKEN_VOLTAGE as a way to
avoid calling regulator_set_voltage() on a fixed regulator, but that's
just duplicating information that already exists -- we should test
whether the regulator is fixed directly, instead of via a capability.
This patch implements that test. We can't reclaim the capability bit
just yet, since there are still boards in arch/arm/ that reference it;
those references can be removed now.
Reported-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds [Sun, 7 Oct 2012 21:38:18 +0000 (06:38 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph updates from Sage Weil:
"The bulk of this pull is a series from Alex that refactors and cleans
up the RBD code to lay the groundwork for supporting the new image
format and evolving feature set. There are also some cleanups in
libceph, and for ceph there's fixed validation of file striping
layouts and a bugfix in the code handling a shrinking MDS cluster."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (71 commits)
ceph: avoid 32-bit page index overflow
ceph: return EIO on invalid layout on GET_DATALOC ioctl
rbd: BUG on invalid layout
ceph: propagate layout error on osd request creation
libceph: check for invalid mapping
ceph: convert to use le32_add_cpu()
ceph: Fix oops when handling mdsmap that decreases max_mds
rbd: update remaining header fields for v2
rbd: get snapshot name for a v2 image
rbd: get the snapshot context for a v2 image
rbd: get image features for a v2 image
rbd: get the object prefix for a v2 rbd image
rbd: add code to get the size of a v2 rbd image
rbd: lay out header probe infrastructure
rbd: encapsulate code that gets snapshot info
rbd: add an rbd features field
rbd: don't use index in __rbd_add_snap_dev()
rbd: kill create_snap sysfs entry
rbd: define rbd_dev_image_id()
rbd: define some new format constants
...
Linus Torvalds [Sun, 7 Oct 2012 21:36:39 +0000 (06:36 +0900)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"The big new feature added this time is supporting online resizing
using the meta_bg feature. This allows us to resize file systems
which are greater than 16TB. In addition, the speed of online
resizing has been improved in general.
We also fix a number of races, some of which could lead to deadlocks,
in ext4's Asynchronous I/O and online defrag support, thanks to good
work by Dmitry Monakhov.
There are also a large number of more minor bug fixes and cleanups
from a number of other ext4 contributors, quite of few of which have
submitted fixes for the first time."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (69 commits)
ext4: fix ext4_flush_completed_IO wait semantics
ext4: fix mtime update in nodelalloc mode
ext4: fix ext_remove_space for punch_hole case
ext4: punch_hole should wait for DIO writers
ext4: serialize truncate with owerwrite DIO workers
ext4: endless truncate due to nonlocked dio readers
ext4: serialize unlocked dio reads with truncate
ext4: serialize dio nonlocked reads with defrag workers
ext4: completed_io locking cleanup
ext4: fix unwritten counter leakage
ext4: give i_aiodio_unwritten a more appropriate name
ext4: ext4_inode_info diet
ext4: convert to use leXX_add_cpu()
ext4: ext4_bread usage audit
fs: reserve fallocate flag codepoint
ext4: remove redundant offset check in mext_check_arguments()
ext4: don't clear orphan list on ro mount with errors
jbd2: fix assertion failure in commit code due to lacking transaction credits
ext4: release donor reference when EXT4_IOC_MOVE_EXT ioctl fails
ext4: enable FITRIM ioctl on bigalloc file system
...
Linus Torvalds [Sun, 7 Oct 2012 21:35:17 +0000 (06:35 +0900)]
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull i2c updates from Jean Delvare:
"Most visible changes are the SMBus multiplexing support added to the
i2c-i801 driver, as well as support for the VIA VX900."
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-piix4: Fix build failure
i2c: Correct struct i2c_driver doc about detection
i2c-i801: Let i2c-mux-gpio find the GPIO chip
i2c-mux-gpio: Update documentation
i2c-mux-gpio: Add support for dynamically allocated GPIO pins
i2c-mux-gpio: Use devm_kzalloc instead of kzalloc
i2c-i801: Support SMBus multiplexing on Asus Z8 series
i2c-viapro: Add VIA VX900 device ID
i2c-parport: i2c_parport_irq can be static
i2c-designware: i2c_dw_xfer_msg can be static
i2c/scx200_*: Replace printks with pr_<level>s
i2c: Make I2C available on UML
i2c: Convert struct i2c_msg initialization to C99 format
i2c-smbus: Convert kzalloc to devm_kzalloc
i2c-mux: Add support for device auto-detection
Linus Torvalds [Sun, 7 Oct 2012 21:33:44 +0000 (06:33 +0900)]
Merge tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time the IOMMU updates contain a bunch of fixes and cleanups to
various IOMMU drivers and the DMA debug code. New features are the
code for IRQ remapping support with the AMD IOMMU (preperation for
that was already merged in the last release) and a debugfs interface
to export some statistics in the NVidia Tegra IOMMU driver."
* tag 'iommu-updates-v3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (27 commits)
iommu/amd: Remove obsolete comment line
dma-debug: Remove local BUS_NOTIFY_UNBOUND_DRIVER define
iommu/amd: Fix possible use after free in get_irq_table()
iommu/amd: Report irq remapping through IOMMU-API
iommu/amd: Print message to system log when irq remapping is enabled
iommu/irq: Use amd_iommu_irq_ops if supported
iommu/amd: Make sure irq remapping still works on dma init failure
iommu/amd: Add initialization routines for AMD interrupt remapping
iommu/amd: Add call-back routine for HPET MSI
iommu/amd: Implement MSI routines for interrupt remapping
iommu/amd: Add IOAPIC remapping routines
iommu/amd: Add routines to manage irq remapping tables
iommu/amd: Add IRTE invalidation routine
iommu/amd: Make sure IOMMU is not considered to translate itself
iommu/amd: Split device table initialization into irq and dma part
iommu/amd: Check if IOAPIC information is correct
iommu/amd: Allocate data structures to keep track of irq remapping tables
iommu/amd: Add slab-cache for irq remapping tables
iommu/amd: Keep track of HPET and IOAPIC device ids
iommu/amd: Fix features reporting
...
projects / karo-tx-linux.git / log