#include <asm/prom.h>
#include <asm/processor.h>
#include <asm/pgtable.h>
-#include <asm/bootinfo.h>
#include <asm/smp.h>
#include <asm/elf.h>
#include <asm/machdep.h>
#include <asm/paca.h>
-#include <asm/ppcdebug.h>
#include <asm/time.h>
#include <asm/cputable.h>
#include <asm/sections.h>
#include <asm/page.h>
#include <asm/mmu.h>
#include <asm/lmb.h>
-#include <asm/iSeries/ItLpNaca.h>
+#include <asm/iseries/it_lp_naca.h>
#include <asm/firmware.h>
#include <asm/systemcfg.h>
+#include <asm/xmon.h>
+#include <asm/udbg.h>
+
+#include "setup.h"
#ifdef DEBUG
#define DBG(fmt...) udbg_printf(fmt)
extern void early_init_devtree(void *flat_dt);
extern void unflatten_device_tree(void);
-extern void smp_release_cpus(void);
-
int have_of = 1;
int boot_cpuid = 0;
int boot_cpuid_phys = 0;
.priority = INT_MIN /* may not return; must be done last */
};
-/*
- * Perhaps we can put the pmac screen_info[] here
- * on pmac as well so we don't need the ifdef's.
- * Until we get multiple-console support in here
- * that is. -- Cort
- * Maybe tie it to serial consoles, since this is really what
- * these processors use on existing boards. -- Dan
- */
-struct screen_info screen_info = {
- .orig_x = 0,
- .orig_y = 25,
- .orig_video_cols = 80,
- .orig_video_lines = 25,
- .orig_video_isVGA = 1,
- .orig_video_points = 16
-};
-
#ifdef CONFIG_SMP
static int smt_enabled_cmdline;
}
early_param("smt-enabled", early_smt_enabled);
-/**
- * setup_cpu_maps - initialize the following cpu maps:
- * cpu_possible_map
- * cpu_present_map
- * cpu_sibling_map
- *
- * Having the possible map set up early allows us to restrict allocations
- * of things like irqstacks to num_possible_cpus() rather than NR_CPUS.
- *
- * We do not initialize the online map here; cpus set their own bits in
- * cpu_online_map as they come up.
- *
- * This function is valid only for Open Firmware systems. finish_device_tree
- * must be called before using this.
- *
- * While we're here, we may as well set the "physical" cpu ids in the paca.
- */
-static void __init setup_cpu_maps(void)
-{
- struct device_node *dn = NULL;
- int cpu = 0;
- int swap_cpuid = 0;
-
- check_smt_enabled();
-
- while ((dn = of_find_node_by_type(dn, "cpu")) && cpu < NR_CPUS) {
- u32 *intserv;
- int j, len = sizeof(u32), nthreads;
-
- intserv = (u32 *)get_property(dn, "ibm,ppc-interrupt-server#s",
- &len);
- if (!intserv)
- intserv = (u32 *)get_property(dn, "reg", NULL);
-
- nthreads = len / sizeof(u32);
-
- for (j = 0; j < nthreads && cpu < NR_CPUS; j++) {
- cpu_set(cpu, cpu_present_map);
- set_hard_smp_processor_id(cpu, intserv[j]);
-
- if (intserv[j] == boot_cpuid_phys)
- swap_cpuid = cpu;
- cpu_set(cpu, cpu_possible_map);
- cpu++;
- }
- }
-
- /* Swap CPU id 0 with boot_cpuid_phys, so we can always assume that
- * boot cpu is logical 0.
- */
- if (boot_cpuid_phys != get_hard_smp_processor_id(0)) {
- u32 tmp;
- tmp = get_hard_smp_processor_id(0);
- set_hard_smp_processor_id(0, boot_cpuid_phys);
- set_hard_smp_processor_id(swap_cpuid, tmp);
- }
-
- /*
- * On pSeries LPAR, we need to know how many cpus
- * could possibly be added to this partition.
- */
- if (systemcfg->platform == PLATFORM_PSERIES_LPAR &&
- (dn = of_find_node_by_path("/rtas"))) {
- int num_addr_cell, num_size_cell, maxcpus;
- unsigned int *ireg;
-
- num_addr_cell = prom_n_addr_cells(dn);
- num_size_cell = prom_n_size_cells(dn);
-
- ireg = (unsigned int *)
- get_property(dn, "ibm,lrdr-capacity", NULL);
-
- if (!ireg)
- goto out;
-
- maxcpus = ireg[num_addr_cell + num_size_cell];
-
- /* Double maxcpus for processors which have SMT capability */
- if (cpu_has_feature(CPU_FTR_SMT))
- maxcpus *= 2;
-
- if (maxcpus > NR_CPUS) {
- printk(KERN_WARNING
- "Partition configured for %d cpus, "
- "operating system maximum is %d.\n",
- maxcpus, NR_CPUS);
- maxcpus = NR_CPUS;
- } else
- printk(KERN_INFO "Partition configured for %d cpus.\n",
- maxcpus);
-
- for (cpu = 0; cpu < maxcpus; cpu++)
- cpu_set(cpu, cpu_possible_map);
- out:
- of_node_put(dn);
- }
-
- /*
- * Do the sibling map; assume only two threads per processor.
- */
- for_each_cpu(cpu) {
- cpu_set(cpu, cpu_sibling_map[cpu]);
- if (cpu_has_feature(CPU_FTR_SMT))
- cpu_set(cpu ^ 0x1, cpu_sibling_map[cpu]);
- }
-
- systemcfg->processorCount = num_present_cpus();
-}
+#else
+#define check_smt_enabled()
#endif /* CONFIG_SMP */
extern struct machdep_calls pSeries_md;
extern struct machdep_calls pmac_md;
extern struct machdep_calls maple_md;
-extern struct machdep_calls bpa_md;
+extern struct machdep_calls cell_md;
extern struct machdep_calls iseries_md;
/* Ultimately, stuff them in an elf section like initcalls... */
#ifdef CONFIG_PPC_MAPLE
&maple_md,
#endif /* CONFIG_PPC_MAPLE */
-#ifdef CONFIG_PPC_BPA
- &bpa_md,
+#ifdef CONFIG_PPC_CELL
+ &cell_md,
#endif
#ifdef CONFIG_PPC_ISERIES
&iseries_md,
DBG(" -> early_setup()\n");
- /*
- * Fill the default DBG level (do we want to keep
- * that old mecanism around forever ?)
- */
- ppcdbg_initialize();
-
/*
* Do early initializations using the flattened device
* tree, like retreiving the physical memory map or
DBG("Found, Initializing memory management...\n");
/*
- * Initialize stab / SLB management
+ * Initialize the MMU Hash table and create the linear mapping
+ * of memory. Has to be done before stab/slb initialization as
+ * this is currently where the page size encoding is obtained
*/
- if (!firmware_has_feature(FW_FEATURE_ISERIES))
- stab_initialize(lpaca->stab_real);
+ htab_initialize();
/*
- * Initialize the MMU Hash table and create the linear mapping
- * of memory
+ * Initialize stab / SLB management except on iSeries
*/
- htab_initialize();
+ if (!firmware_has_feature(FW_FEATURE_ISERIES)) {
+ if (cpu_has_feature(CPU_FTR_SLB))
+ slb_initialize();
+ else
+ stab_initialize(lpaca->stab_real);
+ }
DBG(" <- early_setup()\n");
}
+#if defined(CONFIG_SMP) || defined(CONFIG_KEXEC)
+void smp_release_cpus(void)
+{
+ extern unsigned long __secondary_hold_spinloop;
+
+ DBG(" -> smp_release_cpus()\n");
+
+ /* All secondary cpus are spinning on a common spinloop, release them
+ * all now so they can start to spin on their individual paca
+ * spinloops. For non SMP kernels, the secondary cpus never get out
+ * of the common spinloop.
+ * This is useless but harmless on iSeries, secondaries are already
+ * waiting on their paca spinloops. */
+
+ __secondary_hold_spinloop = 1;
+ mb();
+
+ DBG(" <- smp_release_cpus()\n");
+}
+#else
+#define smp_release_cpus()
+#endif /* CONFIG_SMP || CONFIG_KEXEC */
+
/*
* Initialize some remaining members of the ppc64_caches and systemcfg structures
* (at least until we get rid of them completely). This is mostly some
DBG(" <- initialize_cache_info()\n");
}
-static void __init check_for_initrd(void)
-{
-#ifdef CONFIG_BLK_DEV_INITRD
- u64 *prop;
-
- DBG(" -> check_for_initrd()\n");
-
- if (of_chosen) {
- prop = (u64 *)get_property(of_chosen,
- "linux,initrd-start", NULL);
- if (prop != NULL) {
- initrd_start = (unsigned long)__va(*prop);
- prop = (u64 *)get_property(of_chosen,
- "linux,initrd-end", NULL);
- if (prop != NULL) {
- initrd_end = (unsigned long)__va(*prop);
- initrd_below_start_ok = 1;
- } else
- initrd_start = 0;
- }
- }
-
- /* If we were passed an initrd, set the ROOT_DEV properly if the values
- * look sensible. If not, clear initrd reference.
- */
- if (initrd_start >= KERNELBASE && initrd_end >= KERNELBASE &&
- initrd_end > initrd_start)
- ROOT_DEV = Root_RAM0;
- else
- initrd_start = initrd_end = 0;
-
- if (initrd_start)
- printk("Found initrd at 0x%lx:0x%lx\n", initrd_start, initrd_end);
-
- DBG(" <- check_for_initrd()\n");
-#endif /* CONFIG_BLK_DEV_INITRD */
-}
/*
* Do some initial setup of the system. The parameters are those which
*/
finish_device_tree();
+#ifdef CONFIG_BOOTX_TEXT
+ init_boot_display();
+#endif
+
/*
* Initialize xmon
*/
parse_early_param();
-#ifdef CONFIG_SMP
- /*
- * iSeries has already initialized the cpu maps at this point.
- */
- setup_cpu_maps();
+ check_smt_enabled();
+ smp_setup_cpu_maps();
/* Release secondary cpus out of their spinloops at 0x60 now that
* we can map physical -> logical CPU ids
*/
smp_release_cpus();
-#endif
printk("Starting Linux PPC64 %s\n", system_utsname.version);
printk("-----------------------------------------------------\n");
printk("ppc64_pft_size = 0x%lx\n", ppc64_pft_size);
- printk("ppc64_debug_switch = 0x%lx\n", ppc64_debug_switch);
printk("ppc64_interrupt_controller = 0x%ld\n", ppc64_interrupt_controller);
printk("systemcfg = 0x%p\n", systemcfg);
printk("systemcfg->platform = 0x%x\n", systemcfg->platform);
DBG(" <- setup_system()\n");
}
-/* also used by kexec */
-void machine_shutdown(void)
-{
- if (ppc_md.nvram_sync)
- ppc_md.nvram_sync();
-}
-
-void machine_restart(char *cmd)
-{
- machine_shutdown();
- ppc_md.restart(cmd);
-#ifdef CONFIG_SMP
- smp_send_stop();
-#endif
- printk(KERN_EMERG "System Halted, OK to turn off power\n");
- local_irq_disable();
- while (1) ;
-}
-
-void machine_power_off(void)
-{
- machine_shutdown();
- ppc_md.power_off();
-#ifdef CONFIG_SMP
- smp_send_stop();
-#endif
- printk(KERN_EMERG "System Halted, OK to turn off power\n");
- local_irq_disable();
- while (1) ;
-}
-/* Used by the G5 thermal driver */
-EXPORT_SYMBOL_GPL(machine_power_off);
-
-void machine_halt(void)
-{
- machine_shutdown();
- ppc_md.halt();
-#ifdef CONFIG_SMP
- smp_send_stop();
-#endif
- printk(KERN_EMERG "System Halted, OK to turn off power\n");
- local_irq_disable();
- while (1) ;
-}
-
static int ppc64_panic_event(struct notifier_block *this,
unsigned long event, void *ptr)
{
return NOTIFY_DONE;
}
-
-#ifdef CONFIG_SMP
-DEFINE_PER_CPU(unsigned int, pvr);
-#endif
-
-static int show_cpuinfo(struct seq_file *m, void *v)
-{
- unsigned long cpu_id = (unsigned long)v - 1;
- unsigned int pvr;
- unsigned short maj;
- unsigned short min;
-
- if (cpu_id == NR_CPUS) {
- seq_printf(m, "timebase\t: %lu\n", ppc_tb_freq);
-
- if (ppc_md.get_cpuinfo != NULL)
- ppc_md.get_cpuinfo(m);
-
- return 0;
- }
-
- /* We only show online cpus: disable preempt (overzealous, I
- * knew) to prevent cpu going down. */
- preempt_disable();
- if (!cpu_online(cpu_id)) {
- preempt_enable();
- return 0;
- }
-
-#ifdef CONFIG_SMP
- pvr = per_cpu(pvr, cpu_id);
-#else
- pvr = mfspr(SPRN_PVR);
-#endif
- maj = (pvr >> 8) & 0xFF;
- min = pvr & 0xFF;
-
- seq_printf(m, "processor\t: %lu\n", cpu_id);
- seq_printf(m, "cpu\t\t: ");
-
- if (cur_cpu_spec->pvr_mask)
- seq_printf(m, "%s", cur_cpu_spec->cpu_name);
- else
- seq_printf(m, "unknown (%08x)", pvr);
-
-#ifdef CONFIG_ALTIVEC
- if (cpu_has_feature(CPU_FTR_ALTIVEC))
- seq_printf(m, ", altivec supported");
-#endif /* CONFIG_ALTIVEC */
-
- seq_printf(m, "\n");
-
- /*
- * Assume here that all clock rates are the same in a
- * smp system. -- Cort
- */
- seq_printf(m, "clock\t\t: %lu.%06luMHz\n", ppc_proc_freq / 1000000,
- ppc_proc_freq % 1000000);
-
- seq_printf(m, "revision\t: %hd.%hd\n\n", maj, min);
-
- preempt_enable();
- return 0;
-}
-
-static void *c_start(struct seq_file *m, loff_t *pos)
-{
- return *pos <= NR_CPUS ? (void *)((*pos)+1) : NULL;
-}
-static void *c_next(struct seq_file *m, void *v, loff_t *pos)
-{
- ++*pos;
- return c_start(m, pos);
-}
-static void c_stop(struct seq_file *m, void *v)
-{
-}
-struct seq_operations cpuinfo_op = {
- .start =c_start,
- .next = c_next,
- .stop = c_stop,
- .show = show_cpuinfo,
-};
-
-/*
- * These three variables are used to save values passed to us by prom_init()
- * via the device tree. The TCE variables are needed because with a memory_limit
- * in force we may need to explicitly map the TCE are at the top of RAM.
- */
-unsigned long memory_limit;
-unsigned long tce_alloc_start;
-unsigned long tce_alloc_end;
-
-#ifdef CONFIG_PPC_ISERIES
-/*
- * On iSeries we just parse the mem=X option from the command line.
- * On pSeries it's a bit more complicated, see prom_init_mem()
- */
-static int __init early_parsemem(char *p)
-{
- if (!p)
- return 0;
-
- memory_limit = ALIGN(memparse(p, &p), PAGE_SIZE);
-
- return 0;
-}
-early_param("mem", early_parsemem);
-#endif /* CONFIG_PPC_ISERIES */
-
-#ifdef CONFIG_PPC_MULTIPLATFORM
-static int __init set_preferred_console(void)
-{
- struct device_node *prom_stdout = NULL;
- char *name;
- u32 *spd;
- int offset = 0;
-
- DBG(" -> set_preferred_console()\n");
-
- /* The user has requested a console so this is already set up. */
- if (strstr(saved_command_line, "console=")) {
- DBG(" console was specified !\n");
- return -EBUSY;
- }
-
- if (!of_chosen) {
- DBG(" of_chosen is NULL !\n");
- return -ENODEV;
- }
- /* We are getting a weird phandle from OF ... */
- /* ... So use the full path instead */
- name = (char *)get_property(of_chosen, "linux,stdout-path", NULL);
- if (name == NULL) {
- DBG(" no linux,stdout-path !\n");
- return -ENODEV;
- }
- prom_stdout = of_find_node_by_path(name);
- if (!prom_stdout) {
- DBG(" can't find stdout package %s !\n", name);
- return -ENODEV;
- }
- DBG("stdout is %s\n", prom_stdout->full_name);
-
- name = (char *)get_property(prom_stdout, "name", NULL);
- if (!name) {
- DBG(" stdout package has no name !\n");
- goto not_found;
- }
- spd = (u32 *)get_property(prom_stdout, "current-speed", NULL);
-
- if (0)
- ;
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- else if (strcmp(name, "serial") == 0) {
- int i;
- u32 *reg = (u32 *)get_property(prom_stdout, "reg", &i);
- if (i > 8) {
- switch (reg[1]) {
- case 0x3f8:
- offset = 0;
- break;
- case 0x2f8:
- offset = 1;
- break;
- case 0x898:
- offset = 2;
- break;
- case 0x890:
- offset = 3;
- break;
- default:
- /* We dont recognise the serial port */
- goto not_found;
- }
- }
- }
-#endif /* CONFIG_SERIAL_8250_CONSOLE */
-#ifdef CONFIG_PPC_PSERIES
- else if (strcmp(name, "vty") == 0) {
- u32 *reg = (u32 *)get_property(prom_stdout, "reg", NULL);
- char *compat = (char *)get_property(prom_stdout, "compatible", NULL);
-
- if (reg && compat && (strcmp(compat, "hvterm-protocol") == 0)) {
- /* Host Virtual Serial Interface */
- int offset;
- switch (reg[0]) {
- case 0x30000000:
- offset = 0;
- break;
- case 0x30000001:
- offset = 1;
- break;
- default:
- goto not_found;
- }
- of_node_put(prom_stdout);
- DBG("Found hvsi console at offset %d\n", offset);
- return add_preferred_console("hvsi", offset, NULL);
- } else {
- /* pSeries LPAR virtual console */
- of_node_put(prom_stdout);
- DBG("Found hvc console\n");
- return add_preferred_console("hvc", 0, NULL);
- }
- }
-#endif /* CONFIG_PPC_PSERIES */
-#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
- else if (strcmp(name, "ch-a") == 0)
- offset = 0;
- else if (strcmp(name, "ch-b") == 0)
- offset = 1;
-#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
- else
- goto not_found;
- of_node_put(prom_stdout);
-
- DBG("Found serial console at ttyS%d\n", offset);
-
- if (spd) {
- static char __initdata opt[16];
- sprintf(opt, "%d", *spd);
- return add_preferred_console("ttyS", offset, opt);
- } else
- return add_preferred_console("ttyS", offset, NULL);
-
- not_found:
- DBG("No preferred console found !\n");
- of_node_put(prom_stdout);
- return -ENODEV;
-}
-console_initcall(set_preferred_console);
-#endif /* CONFIG_PPC_MULTIPLATFORM */
-
#ifdef CONFIG_IRQSTACKS
static void __init irqstack_early_init(void)
{
* SLB misses on them.
*/
for_each_cpu(i) {
- softirq_ctx[i] = (struct thread_info *)__va(lmb_alloc_base(THREAD_SIZE,
- THREAD_SIZE, 0x10000000));
- hardirq_ctx[i] = (struct thread_info *)__va(lmb_alloc_base(THREAD_SIZE,
- THREAD_SIZE, 0x10000000));
+ softirq_ctx[i] = (struct thread_info *)
+ __va(lmb_alloc_base(THREAD_SIZE,
+ THREAD_SIZE, 0x10000000));
+ hardirq_ctx[i] = (struct thread_info *)
+ __va(lmb_alloc_base(THREAD_SIZE,
+ THREAD_SIZE, 0x10000000));
}
}
#else
limit = min(0x10000000UL, lmb.rmo_size);
for_each_cpu(i)
- paca[i].emergency_sp = __va(lmb_alloc_base(PAGE_SIZE, 128,
- limit)) + PAGE_SIZE;
+ paca[i].emergency_sp =
+ __va(lmb_alloc_base(HW_PAGE_SIZE, 128, limit)) + HW_PAGE_SIZE;
}
/*
/* initialize the syscall map in systemcfg */
setup_syscall_map();
+#ifdef CONFIG_DUMMY_CONSOLE
+ conswitchp = &dummy_con;
+#endif
+
ppc_md.setup_arch();
/* Use the default idle loop if the platform hasn't provided one. */
printk("[terminate]%04x %s\n", src, msg);
}
-/* This should only be called on processor 0 during calibrate decr */
-void __init setup_default_decr(void)
-{
- struct paca_struct *lpaca = get_paca();
-
- lpaca->default_decr = tb_ticks_per_jiffy;
- lpaca->next_jiffy_update_tb = get_tb() + tb_ticks_per_jiffy;
-}
-
#ifndef CONFIG_PPC_ISERIES
/*
* This function can be used by platforms to "find" legacy serial ports.
}
EXPORT_SYMBOL(check_legacy_ioport);
-#ifdef CONFIG_XMON
-static int __init early_xmon(char *p)
-{
- /* ensure xmon is enabled */
- if (p) {
- if (strncmp(p, "on", 2) == 0)
- xmon_init(1);
- if (strncmp(p, "off", 3) == 0)
- xmon_init(0);
- if (strncmp(p, "early", 5) != 0)
- return 0;
- }
- xmon_init(1);
- debugger(NULL);
-
- return 0;
-}
-early_param("xmon", early_xmon);
-#endif
-
void cpu_die(void)
{
if (ppc_md.cpu_die)
projects / karo-tx-linux.git / blobdiff