# put drivers in the right section, in alphabetical order
-config GPIO_DA9052
- tristate "Dialog DA9052 GPIO"
- depends on PMIC_DA9052
- help
- Say yes here to enable the GPIO driver for the DA9052 chip.
-
-config GPIO_DA9055
- tristate "Dialog Semiconductor DA9055 GPIO"
- depends on MFD_DA9055
- help
- Say yes here to enable the GPIO driver for the DA9055 chip.
-
- The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
- be controller by this driver.
-
- If driver is built as a module it will be called gpio-da9055.
-
+# This symbol is selected by both I2C and SPI expanders
config GPIO_MAX730X
tristate
-comment "Memory mapped GPIO drivers:"
+menu "Memory mapped GPIO drivers"
config GPIO_74XX_MMIO
tristate "GPIO driver for 74xx-ICs with MMIO access"
If driver is built as a module it will be called gpio-altera.
+config GPIO_BCM_KONA
+ bool "Broadcom Kona GPIO"
+ depends on OF_GPIO && (ARCH_BCM_MOBILE || COMPILE_TEST)
+ help
+ Turn on GPIO support for Broadcom "Kona" chips.
+
config GPIO_CLPS711X
tristate "CLPS711X GPIO support"
depends on ARCH_CLPS711X || COMPILE_TEST
config GPIO_DWAPB
tristate "Synopsys DesignWare APB GPIO driver"
- depends on ((ARM || ARM64) && OF_GPIO) || X86_INTEL_QUARK
select GPIO_GENERIC
select GENERIC_IRQ_CHIP
help
Say yes here to support the STA2x11/ConneXt GPIO device.
The GPIO module has 128 GPIO pins with alternate functions.
+config GPIO_STP_XWAY
+ bool "XWAY STP GPIOs"
+ depends on SOC_XWAY
+ help
+ This enables support for the Serial To Parallel (STP) unit found on
+ XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
+ that can be up to 24 bit. This peripheral is aimed at driving leds.
+ Some of the gpios/leds can be auto updated by the soc with dsl and
+ phy status.
+
config GPIO_SYSCON
tristate "GPIO based on SYSCON"
depends on MFD_SYSCON && OF
help
Say yes here to support Xilinx Zynq GPIO controller.
-comment "I2C GPIO expanders:"
+endmenu
-config GPIO_ADP5520
- tristate "GPIO Support for ADP5520 PMIC"
- depends on PMIC_ADP5520
- help
- This option enables support for on-chip GPIO found
- on Analog Devices ADP5520 PMICs.
+menu "I2C GPIO expanders"
+ depends on I2C
config GPIO_ADP5588
tristate "ADP5588 I2C GPIO expander"
enough to represent all pins, but the driver will assume a
register layout for 64 pins (8 registers).
-config GPIO_ARIZONA
- tristate "Wolfson Microelectronics Arizona class devices"
- depends on MFD_ARIZONA
- help
- Support for GPIOs on Wolfson Arizona class devices.
-
-config GPIO_CRYSTAL_COVE
- tristate "GPIO support for Crystal Cove PMIC"
- depends on INTEL_SOC_PMIC
- select GPIOLIB_IRQCHIP
- help
- Support for GPIO pins on Crystal Cove PMIC.
-
- Say Yes if you have a Intel SoC based tablet with Crystal Cove PMIC
- inside.
-
- This driver can also be built as a module. If so, the module will be
- called gpio-crystalcove.
-
-config GPIO_LP3943
- tristate "TI/National Semiconductor LP3943 GPIO expander"
- depends on MFD_LP3943
- help
- GPIO driver for LP3943 MFD.
- LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
- Open drain outputs are required for this usage.
-
config GPIO_MAX7300
tristate "Maxim MAX7300 GPIO expander"
depends on I2C
This driver provides an in-kernel interface to those GPIOs using
platform-neutral GPIO calls.
+config GPIO_SX150X
+ bool "Semtech SX150x I2C GPIO expander"
+ depends on I2C=y
+ select GPIOLIB_IRQCHIP
+ default n
+ help
+ Say yes here to provide support for Semtech SX150-series I2C
+ GPIO expanders. Compatible models include:
+
+ 8 bits: sx1508q
+ 16 bits: sx1509q
+
+endmenu
+
+menu "MFD GPIO expanders"
+
+config GPIO_ADP5520
+ tristate "GPIO Support for ADP5520 PMIC"
+ depends on PMIC_ADP5520
+ help
+ This option enables support for on-chip GPIO found
+ on Analog Devices ADP5520 PMICs.
+
+config GPIO_ARIZONA
+ tristate "Wolfson Microelectronics Arizona class devices"
+ depends on MFD_ARIZONA
+ help
+ Support for GPIOs on Wolfson Arizona class devices.
+
+config GPIO_CRYSTAL_COVE
+ tristate "GPIO support for Crystal Cove PMIC"
+ depends on INTEL_SOC_PMIC
+ select GPIOLIB_IRQCHIP
+ help
+ Support for GPIO pins on Crystal Cove PMIC.
+
+ Say Yes if you have a Intel SoC based tablet with Crystal Cove PMIC
+ inside.
+
+ This driver can also be built as a module. If so, the module will be
+ called gpio-crystalcove.
+
+config GPIO_CS5535
+ tristate "AMD CS5535/CS5536 GPIO support"
+ depends on MFD_CS5535
+ help
+ The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
+ can be used for quite a number of things. The CS5535/6 is found on
+ AMD Geode and Lemote Yeeloong devices.
+
+ If unsure, say N.
+
+config GPIO_DA9052
+ tristate "Dialog DA9052 GPIO"
+ depends on PMIC_DA9052
+ help
+ Say yes here to enable the GPIO driver for the DA9052 chip.
+
+config GPIO_DA9055
+ tristate "Dialog Semiconductor DA9055 GPIO"
+ depends on MFD_DA9055
+ help
+ Say yes here to enable the GPIO driver for the DA9055 chip.
+
+ The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
+ be controller by this driver.
+
+ If driver is built as a module it will be called gpio-da9055.
+
+config GPIO_DLN2
+ tristate "Diolan DLN2 GPIO support"
+ depends on MFD_DLN2
+ select GPIOLIB_IRQCHIP
+
+ help
+ Select this option to enable GPIO driver for the Diolan DLN2
+ board.
+
+ This driver can also be built as a module. If so, the module
+ will be called gpio-dln2.
+
+config GPIO_JANZ_TTL
+ tristate "Janz VMOD-TTL Digital IO Module"
+ depends on MFD_JANZ_CMODIO
+ help
+ This enables support for the Janz VMOD-TTL Digital IO module.
+ This driver provides support for driving the pins in output
+ mode only. Input mode is not supported.
+
+config GPIO_KEMPLD
+ tristate "Kontron ETX / COMexpress GPIO"
+ depends on MFD_KEMPLD
+ help
+ This enables support for the PLD GPIO interface on some Kontron ETX
+ and COMexpress (ETXexpress) modules.
+
+ This driver can also be built as a module. If so, the module will be
+ called gpio-kempld.
+
+config GPIO_LP3943
+ tristate "TI/National Semiconductor LP3943 GPIO expander"
+ depends on MFD_LP3943
+ help
+ GPIO driver for LP3943 MFD.
+ LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
+ Open drain outputs are required for this usage.
+
+config GPIO_MSIC
+ bool "Intel MSIC mixed signal gpio support"
+ depends on MFD_INTEL_MSIC
+ help
+ Enable support for GPIO on intel MSIC controllers found in
+ intel MID devices
+
+config GPIO_PALMAS
+ bool "TI PALMAS series PMICs GPIO"
+ depends on MFD_PALMAS
+ help
+ Select this option to enable GPIO driver for the TI PALMAS
+ series chip family.
+
config GPIO_RC5T583
bool "RICOH RC5T583 GPIO"
depends on MFD_RC5T583
This enables support for the GPIOs found on the STMPE I/O
Expanders.
-config GPIO_STP_XWAY
- bool "XWAY STP GPIOs"
- depends on SOC_XWAY
- help
- This enables support for the Serial To Parallel (STP) unit found on
- XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
- that can be up to 24 bit. This peripheral is aimed at driving leds.
- Some of the gpios/leds can be auto updated by the soc with dsl and
- phy status.
-
-config GPIO_SX150X
- bool "Semtech SX150x I2C GPIO expander"
- depends on I2C=y
- select GPIOLIB_IRQCHIP
- default n
- help
- Say yes here to provide support for Semtech SX150-series I2C
- GPIO expanders. Compatible models include:
-
- 8 bits: sx1508q
- 16 bits: sx1509q
-
config GPIO_TC3589X
bool "TC3589X GPIOs"
depends on MFD_TC3589X
+ depends on OF_GPIO
select GPIOLIB_IRQCHIP
help
This enables support for the GPIOs found on the TC3589X
I/O Expander.
+config GPIO_TIMBERDALE
+ bool "Support for timberdale GPIO IP"
+ depends on MFD_TIMBERDALE
+ ---help---
+ Add support for the GPIO IP in the timberdale FPGA.
+
+config GPIO_TPS6586X
+ bool "TPS6586X GPIO"
+ depends on MFD_TPS6586X
+ help
+ Select this option to enable GPIO driver for the TPS6586X
+ chip family.
+
+config GPIO_TPS65910
+ bool "TPS65910 GPIO"
+ depends on MFD_TPS65910
+ help
+ Select this option to enable GPIO driver for the TPS65910
+ chip family.
+
config GPIO_TPS65912
tristate "TI TPS65912 GPIO"
depends on (MFD_TPS65912_I2C || MFD_TPS65912_SPI)
Say yes here to access the GPO signals of twl6040
audio chip from Texas Instruments.
+config GPIO_UCB1400
+ tristate "Philips UCB1400 GPIO"
+ depends on UCB1400_CORE
+ help
+ This enables support for the Philips UCB1400 GPIO pins.
+ The UCB1400 is an AC97 audio codec.
+
config GPIO_WM831X
tristate "WM831x GPIOs"
depends on MFD_WM831X
Say yes here to access the GPIO signals of WM8994 audio hub
CODECs from Wolfson Microelectronics.
-comment "PCI GPIO expanders:"
+endmenu
+
+menu "PCI GPIO expanders"
+ depends on PCI
config GPIO_AMD8111
tristate "AMD 8111 GPIO driver"
If unsure, say N.
-config GPIO_CS5535
- tristate "AMD CS5535/CS5536 GPIO support"
- depends on MFD_CS5535
- help
- The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
- can be used for quite a number of things. The CS5535/6 is found on
- AMD Geode and Lemote Yeeloong devices.
-
- If unsure, say N.
-
config GPIO_INTEL_MID
bool "Intel Mid GPIO support"
depends on PCI && X86
help
Say Y here to support Intel Sodaville GPIO.
-config GPIO_TIMBERDALE
- bool "Support for timberdale GPIO IP"
- depends on MFD_TIMBERDALE
- ---help---
- Add support for the GPIO IP in the timberdale FPGA.
+endmenu
-comment "SPI GPIO expanders:"
+menu "SPI GPIO expanders"
+ depends on SPI_MASTER
config GPIO_74X164
tristate "74x164 serial-in/parallel-out 8-bits shift register"
SPI driver for Freescale MC33880 high-side/low-side switch.
This provides GPIO interface supporting inputs and outputs.
-comment "AC97 GPIO expanders:"
+endmenu
-config GPIO_UCB1400
- tristate "Philips UCB1400 GPIO"
- depends on UCB1400_CORE
- help
- This enables support for the Philips UCB1400 GPIO pins.
- The UCB1400 is an AC97 audio codec.
-
-comment "LPC GPIO expanders:"
-
-config GPIO_KEMPLD
- tristate "Kontron ETX / COMexpress GPIO"
- depends on MFD_KEMPLD
- help
- This enables support for the PLD GPIO interface on some Kontron ETX
- and COMexpress (ETXexpress) modules.
-
- This driver can also be built as a module. If so, the module will be
- called gpio-kempld.
-
-comment "MODULbus GPIO expanders:"
-
-config GPIO_JANZ_TTL
- tristate "Janz VMOD-TTL Digital IO Module"
- depends on MFD_JANZ_CMODIO
- help
- This enables support for the Janz VMOD-TTL Digital IO module.
- This driver provides support for driving the pins in output
- mode only. Input mode is not supported.
-
-config GPIO_PALMAS
- bool "TI PALMAS series PMICs GPIO"
- depends on MFD_PALMAS
- help
- Select this option to enable GPIO driver for the TI PALMAS
- series chip family.
-
-config GPIO_TPS6586X
- bool "TPS6586X GPIO"
- depends on MFD_TPS6586X
- help
- Select this option to enable GPIO driver for the TPS6586X
- chip family.
-
-config GPIO_TPS65910
- bool "TPS65910 GPIO"
- depends on MFD_TPS65910
- help
- Select this option to enable GPIO driver for the TPS65910
- chip family.
-
-config GPIO_MSIC
- bool "Intel MSIC mixed signal gpio support"
- depends on MFD_INTEL_MSIC
- help
- Enable support for GPIO on intel MSIC controllers found in
- intel MID devices
-
-config GPIO_BCM_KONA
- bool "Broadcom Kona GPIO"
- depends on OF_GPIO && (ARCH_BCM_MOBILE || COMPILE_TEST)
- help
- Turn on GPIO support for Broadcom "Kona" chips.
-
-comment "USB GPIO expanders:"
+menu "USB GPIO expanders"
+ depends on USB
config GPIO_VIPERBOARD
tristate "Viperboard GPIO a & b support"
River Tech's viperboard.h for detailed meaning
of the module parameters.
-config GPIO_DLN2
- tristate "Diolan DLN2 GPIO support"
- depends on MFD_DLN2
- select GPIOLIB_IRQCHIP
-
- help
- Select this option to enable GPIO driver for the Diolan DLN2
- board.
-
- This driver can also be built as a module. If so, the module
- will be called gpio-dln2.
+endmenu
endif
projects / karo-tx-linux.git / blobdiff