#define DW_MCI_FREQ_MAX 200000000 /* unit: HZ */
#define DW_MCI_FREQ_MIN 400000 /* unit: HZ */
-#ifdef CONFIG_MMC_DW_IDMAC
#define IDMAC_INT_CLR (SDMMC_IDMAC_INT_AI | SDMMC_IDMAC_INT_NI | \
SDMMC_IDMAC_INT_CES | SDMMC_IDMAC_INT_DU | \
SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \
/* Each descriptor can transfer up to 4KB of data in chained mode */
#define DW_MCI_DESC_DATA_LENGTH 0x1000
-#endif /* CONFIG_MMC_DW_IDMAC */
static bool dw_mci_reset(struct dw_mci *host);
static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset);
return DMA_FROM_DEVICE;
}
-#ifdef CONFIG_MMC_DW_IDMAC
static void dw_mci_dma_cleanup(struct dw_mci *host)
{
struct mmc_data *data = host->data;
mci_writel(host, BMOD, temp);
}
-static void dw_mci_idmac_complete_dma(struct dw_mci *host)
+static void dw_mci_dmac_complete_dma(void *arg)
{
+ struct dw_mci *host = arg;
struct mmc_data *data = host->data;
dev_vdbg(host->dev, "DMA complete\n");
+ if ((host->use_dma == TRANS_MODE_EDMAC) &&
+ data && (data->flags & MMC_DATA_READ))
+ /* Invalidate cache after read */
+ dma_sync_sg_for_cpu(mmc_dev(host->cur_slot->mmc),
+ data->sg,
+ data->sg_len,
+ DMA_FROM_DEVICE);
+
host->dma_ops->cleanup(host);
/*
wmb(); /* drain writebuffer */
}
-static void dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
+static int dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
{
u32 temp;
/* Start it running */
mci_writel(host, PLDMND, 1);
+
+ return 0;
}
static int dw_mci_idmac_init(struct dw_mci *host)
.init = dw_mci_idmac_init,
.start = dw_mci_idmac_start_dma,
.stop = dw_mci_idmac_stop_dma,
- .complete = dw_mci_idmac_complete_dma,
+ .complete = dw_mci_dmac_complete_dma,
+ .cleanup = dw_mci_dma_cleanup,
+};
+
+static void dw_mci_edmac_stop_dma(struct dw_mci *host)
+{
+ dmaengine_terminate_all(host->dms->ch);
+}
+
+static int dw_mci_edmac_start_dma(struct dw_mci *host,
+ unsigned int sg_len)
+{
+ struct dma_slave_config cfg;
+ struct dma_async_tx_descriptor *desc = NULL;
+ struct scatterlist *sgl = host->data->sg;
+ const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
+ u32 sg_elems = host->data->sg_len;
+ u32 fifoth_val;
+ u32 fifo_offset = host->fifo_reg - host->regs;
+ int ret = 0;
+
+ /* Set external dma config: burst size, burst width */
+ cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
+ cfg.src_addr = cfg.dst_addr;
+ cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+
+ /* Match burst msize with external dma config */
+ fifoth_val = mci_readl(host, FIFOTH);
+ cfg.dst_maxburst = mszs[(fifoth_val >> 28) & 0x7];
+ cfg.src_maxburst = cfg.dst_maxburst;
+
+ if (host->data->flags & MMC_DATA_WRITE)
+ cfg.direction = DMA_MEM_TO_DEV;
+ else
+ cfg.direction = DMA_DEV_TO_MEM;
+
+ ret = dmaengine_slave_config(host->dms->ch, &cfg);
+ if (ret) {
+ dev_err(host->dev, "Failed to config edmac.\n");
+ return -EBUSY;
+ }
+
+ desc = dmaengine_prep_slave_sg(host->dms->ch, sgl,
+ sg_len, cfg.direction,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc) {
+ dev_err(host->dev, "Can't prepare slave sg.\n");
+ return -EBUSY;
+ }
+
+ /* Set dw_mci_dmac_complete_dma as callback */
+ desc->callback = dw_mci_dmac_complete_dma;
+ desc->callback_param = (void *)host;
+ dmaengine_submit(desc);
+
+ /* Flush cache before write */
+ if (host->data->flags & MMC_DATA_WRITE)
+ dma_sync_sg_for_device(mmc_dev(host->cur_slot->mmc), sgl,
+ sg_elems, DMA_TO_DEVICE);
+
+ dma_async_issue_pending(host->dms->ch);
+
+ return 0;
+}
+
+static int dw_mci_edmac_init(struct dw_mci *host)
+{
+ /* Request external dma channel */
+ host->dms = kzalloc(sizeof(struct dw_mci_dma_slave), GFP_KERNEL);
+ if (!host->dms)
+ return -ENOMEM;
+
+ host->dms->ch = dma_request_slave_channel(host->dev, "rx-tx");
+ if (!host->dms->ch) {
+ dev_err(host->dev, "Failed to get external DMA channel.\n");
+ kfree(host->dms);
+ host->dms = NULL;
+ return -ENXIO;
+ }
+
+ return 0;
+}
+
+static void dw_mci_edmac_exit(struct dw_mci *host)
+{
+ if (host->dms) {
+ if (host->dms->ch) {
+ dma_release_channel(host->dms->ch);
+ host->dms->ch = NULL;
+ }
+ kfree(host->dms);
+ host->dms = NULL;
+ }
+}
+
+static const struct dw_mci_dma_ops dw_mci_edmac_ops = {
+ .init = dw_mci_edmac_init,
+ .exit = dw_mci_edmac_exit,
+ .start = dw_mci_edmac_start_dma,
+ .stop = dw_mci_edmac_stop_dma,
+ .complete = dw_mci_dmac_complete_dma,
.cleanup = dw_mci_dma_cleanup,
};
-#endif /* CONFIG_MMC_DW_IDMAC */
static int dw_mci_pre_dma_transfer(struct dw_mci *host,
struct mmc_data *data,
static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
{
-#ifdef CONFIG_MMC_DW_IDMAC
unsigned int blksz = data->blksz;
const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
u32 fifo_width = 1 << host->data_shift;
u32 msize = 0, rx_wmark = 1, tx_wmark, tx_wmark_invers;
int idx = ARRAY_SIZE(mszs) - 1;
+ /* pio should ship this scenario */
+ if (!host->use_dma)
+ return;
+
tx_wmark = (host->fifo_depth) / 2;
tx_wmark_invers = host->fifo_depth - tx_wmark;
done:
fifoth_val = SDMMC_SET_FIFOTH(msize, rx_wmark, tx_wmark);
mci_writel(host, FIFOTH, fifoth_val);
-#endif
}
static void dw_mci_ctrl_rd_thld(struct dw_mci *host, struct mmc_data *data)
host->using_dma = 1;
- dev_vdbg(host->dev,
- "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n",
- (unsigned long)host->sg_cpu, (unsigned long)host->sg_dma,
- sg_len);
+ if (host->use_dma == TRANS_MODE_IDMAC)
+ dev_vdbg(host->dev,
+ "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n",
+ (unsigned long)host->sg_cpu,
+ (unsigned long)host->sg_dma,
+ sg_len);
/*
* Decide the MSIZE and RX/TX Watermark.
mci_writel(host, INTMASK, temp);
spin_unlock_irqrestore(&host->irq_lock, irqflags);
- host->dma_ops->start(host, sg_len);
+ if (host->dma_ops->start(host, sg_len)) {
+ /* We can't do DMA */
+ dev_err(host->dev, "%s: failed to start DMA.\n", __func__);
+ return -ENODEV;
+ }
return 0;
}
/* DDR mode set */
if (ios->timing == MMC_TIMING_MMC_DDR52 ||
+ ios->timing == MMC_TIMING_UHS_DDR50 ||
ios->timing == MMC_TIMING_MMC_HS400)
regs |= ((0x1 << slot->id) << 16);
else
const struct dw_mci_drv_data *drv_data = host->drv_data;
u32 uhs;
u32 v18 = SDMMC_UHS_18V << slot->id;
- int min_uv, max_uv;
int ret;
if (drv_data && drv_data->switch_voltage)
* does no harm but you need to set the regulator directly. Try both.
*/
uhs = mci_readl(host, UHS_REG);
- if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
- min_uv = 2700000;
- max_uv = 3600000;
+ if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
uhs &= ~v18;
- } else {
- min_uv = 1700000;
- max_uv = 1950000;
+ else
uhs |= v18;
- }
+
if (!IS_ERR(mmc->supply.vqmmc)) {
- ret = regulator_set_voltage(mmc->supply.vqmmc, min_uv, max_uv);
+ ret = mmc_regulator_set_vqmmc(mmc, ios);
if (ret) {
dev_dbg(&mmc->class_dev,
- "Regulator set error %d: %d - %d\n",
- ret, min_uv, max_uv);
+ "Regulator set error %d - %s V\n",
+ ret, uhs & v18 ? "1.8" : "3.3");
return ret;
}
}
int err = -EINVAL;
if (drv_data && drv_data->execute_tuning)
- err = drv_data->execute_tuning(slot);
+ err = drv_data->execute_tuning(slot, opcode);
return err;
}
}
-#ifdef CONFIG_MMC_DW_IDMAC
- /* Handle DMA interrupts */
+ if (host->use_dma != TRANS_MODE_IDMAC)
+ return IRQ_HANDLED;
+
+ /* Handle IDMA interrupts */
if (host->dma_64bit_address == 1) {
pending = mci_readl(host, IDSTS64);
if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI |
SDMMC_IDMAC_INT_RI);
mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
- host->dma_ops->complete(host);
+ host->dma_ops->complete((void *)host);
}
} else {
pending = mci_readl(host, IDSTS);
mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI |
SDMMC_IDMAC_INT_RI);
mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
- host->dma_ops->complete(host);
+ host->dma_ops->complete((void *)host);
}
}
-#endif
return IRQ_HANDLED;
}
goto err_host_allocated;
/* Useful defaults if platform data is unset. */
- if (host->use_dma) {
+ if (host->use_dma == TRANS_MODE_IDMAC) {
mmc->max_segs = host->ring_size;
mmc->max_blk_size = 65536;
mmc->max_seg_size = 0x1000;
mmc->max_req_size = mmc->max_seg_size * host->ring_size;
mmc->max_blk_count = mmc->max_req_size / 512;
+ } else if (host->use_dma == TRANS_MODE_EDMAC) {
+ mmc->max_segs = 64;
+ mmc->max_blk_size = 65536;
+ mmc->max_blk_count = 65535;
+ mmc->max_req_size =
+ mmc->max_blk_size * mmc->max_blk_count;
+ mmc->max_seg_size = mmc->max_req_size;
} else {
+ /* TRANS_MODE_PIO */
mmc->max_segs = 64;
mmc->max_blk_size = 65536; /* BLKSIZ is 16 bits */
mmc->max_blk_count = 512;
static void dw_mci_init_dma(struct dw_mci *host)
{
int addr_config;
- /* Check ADDR_CONFIG bit in HCON to find IDMAC address bus width */
- addr_config = (mci_readl(host, HCON) >> 27) & 0x01;
-
- if (addr_config == 1) {
- /* host supports IDMAC in 64-bit address mode */
- host->dma_64bit_address = 1;
- dev_info(host->dev, "IDMAC supports 64-bit address mode.\n");
- if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
- dma_set_coherent_mask(host->dev, DMA_BIT_MASK(64));
- } else {
- /* host supports IDMAC in 32-bit address mode */
- host->dma_64bit_address = 0;
- dev_info(host->dev, "IDMAC supports 32-bit address mode.\n");
- }
+ struct device *dev = host->dev;
+ struct device_node *np = dev->of_node;
- /* Alloc memory for sg translation */
- host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE,
- &host->sg_dma, GFP_KERNEL);
- if (!host->sg_cpu) {
- dev_err(host->dev, "%s: could not alloc DMA memory\n",
- __func__);
+ /*
+ * Check tansfer mode from HCON[17:16]
+ * Clear the ambiguous description of dw_mmc databook:
+ * 2b'00: No DMA Interface -> Actually means using Internal DMA block
+ * 2b'01: DesignWare DMA Interface -> Synopsys DW-DMA block
+ * 2b'10: Generic DMA Interface -> non-Synopsys generic DMA block
+ * 2b'11: Non DW DMA Interface -> pio only
+ * Compared to DesignWare DMA Interface, Generic DMA Interface has a
+ * simpler request/acknowledge handshake mechanism and both of them
+ * are regarded as external dma master for dw_mmc.
+ */
+ host->use_dma = SDMMC_GET_TRANS_MODE(mci_readl(host, HCON));
+ if (host->use_dma == DMA_INTERFACE_IDMA) {
+ host->use_dma = TRANS_MODE_IDMAC;
+ } else if (host->use_dma == DMA_INTERFACE_DWDMA ||
+ host->use_dma == DMA_INTERFACE_GDMA) {
+ host->use_dma = TRANS_MODE_EDMAC;
+ } else {
goto no_dma;
}
/* Determine which DMA interface to use */
-#ifdef CONFIG_MMC_DW_IDMAC
- host->dma_ops = &dw_mci_idmac_ops;
- dev_info(host->dev, "Using internal DMA controller.\n");
-#endif
+ if (host->use_dma == TRANS_MODE_IDMAC) {
+ /*
+ * Check ADDR_CONFIG bit in HCON to find
+ * IDMAC address bus width
+ */
+ addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON));
+
+ if (addr_config == 1) {
+ /* host supports IDMAC in 64-bit address mode */
+ host->dma_64bit_address = 1;
+ dev_info(host->dev,
+ "IDMAC supports 64-bit address mode.\n");
+ if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
+ dma_set_coherent_mask(host->dev,
+ DMA_BIT_MASK(64));
+ } else {
+ /* host supports IDMAC in 32-bit address mode */
+ host->dma_64bit_address = 0;
+ dev_info(host->dev,
+ "IDMAC supports 32-bit address mode.\n");
+ }
- if (!host->dma_ops)
- goto no_dma;
+ /* Alloc memory for sg translation */
+ host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE,
+ &host->sg_dma, GFP_KERNEL);
+ if (!host->sg_cpu) {
+ dev_err(host->dev,
+ "%s: could not alloc DMA memory\n",
+ __func__);
+ goto no_dma;
+ }
+
+ host->dma_ops = &dw_mci_idmac_ops;
+ dev_info(host->dev, "Using internal DMA controller.\n");
+ } else {
+ /* TRANS_MODE_EDMAC: check dma bindings again */
+ if ((of_property_count_strings(np, "dma-names") < 0) ||
+ (!of_find_property(np, "dmas", NULL))) {
+ goto no_dma;
+ }
+ host->dma_ops = &dw_mci_edmac_ops;
+ dev_info(host->dev, "Using external DMA controller.\n");
+ }
if (host->dma_ops->init && host->dma_ops->start &&
host->dma_ops->stop && host->dma_ops->cleanup) {
goto no_dma;
}
- host->use_dma = 1;
return;
no_dma:
dev_info(host->dev, "Using PIO mode.\n");
- host->use_dma = 0;
+ host->use_dma = TRANS_MODE_PIO;
}
static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset)
}
}
-#if IS_ENABLED(CONFIG_MMC_DW_IDMAC)
- /* It is also recommended that we reset and reprogram idmac */
- dw_mci_idmac_reset(host);
-#endif
+ if (host->use_dma == TRANS_MODE_IDMAC)
+ /* It is also recommended that we reset and reprogram idmac */
+ dw_mci_idmac_reset(host);
ret = true;
* Get the host data width - this assumes that HCON has been set with
* the correct values.
*/
- i = (mci_readl(host, HCON) >> 7) & 0x7;
+ i = SDMMC_GET_HDATA_WIDTH(mci_readl(host, HCON));
if (!i) {
host->push_data = dw_mci_push_data16;
host->pull_data = dw_mci_pull_data16;
if (host->pdata->num_slots)
host->num_slots = host->pdata->num_slots;
else
- host->num_slots = ((mci_readl(host, HCON) >> 1) & 0x1F) + 1;
+ host->num_slots = SDMMC_GET_SLOT_NUM(mci_readl(host, HCON));
/*
* Enable interrupts for command done, data over, data empty,
*/
int dw_mci_suspend(struct dw_mci *host)
{
+ if (host->use_dma && host->dma_ops->exit)
+ host->dma_ops->exit(host);
+
return 0;
}
EXPORT_SYMBOL(dw_mci_suspend);
projects / karo-tx-linux.git / blobdiff