+++ /dev/null
-#ifndef _PPC64_HVCALL_H
-#define _PPC64_HVCALL_H
-
-#define HVSC .long 0x44000022
-
-#define H_Success 0
-#define H_Busy 1 /* Hardware busy -- retry later */
-#define H_Constrained 4 /* Resource request constrained to max allowed */
-#define H_LongBusyStartRange 9900 /* Start of long busy range */
-#define H_LongBusyOrder1msec 9900 /* Long busy, hint that 1msec is a good time to retry */
-#define H_LongBusyOrder10msec 9901 /* Long busy, hint that 10msec is a good time to retry */
-#define H_LongBusyOrder100msec 9902 /* Long busy, hint that 100msec is a good time to retry */
-#define H_LongBusyOrder1sec 9903 /* Long busy, hint that 1sec is a good time to retry */
-#define H_LongBusyOrder10sec 9904 /* Long busy, hint that 10sec is a good time to retry */
-#define H_LongBusyOrder100sec 9905 /* Long busy, hint that 100sec is a good time to retry */
-#define H_LongBusyEndRange 9905 /* End of long busy range */
-#define H_Hardware -1 /* Hardware error */
-#define H_Function -2 /* Function not supported */
-#define H_Privilege -3 /* Caller not privileged */
-#define H_Parameter -4 /* Parameter invalid, out-of-range or conflicting */
-#define H_Bad_Mode -5 /* Illegal msr value */
-#define H_PTEG_Full -6 /* PTEG is full */
-#define H_Not_Found -7 /* PTE was not found" */
-#define H_Reserved_DABR -8 /* DABR address is reserved by the hypervisor on this processor" */
-#define H_NoMem -9
-#define H_Authority -10
-#define H_Permission -11
-#define H_Dropped -12
-#define H_SourceParm -13
-#define H_DestParm -14
-#define H_RemoteParm -15
-#define H_Resource -16
-
-/* Long Busy is a condition that can be returned by the firmware
- * when a call cannot be completed now, but the identical call
- * should be retried later. This prevents calls blocking in the
- * firmware for long periods of time. Annoyingly the firmware can return
- * a range of return codes, hinting at how long we should wait before
- * retrying. If you don't care for the hint, the macro below is a good
- * way to check for the long_busy return codes
- */
-#define H_isLongBusy(x) ((x >= H_LongBusyStartRange) && (x <= H_LongBusyEndRange))
-
-/* Flags */
-#define H_LARGE_PAGE (1UL<<(63-16))
-#define H_EXACT (1UL<<(63-24)) /* Use exact PTE or return H_PTEG_FULL */
-#define H_R_XLATE (1UL<<(63-25)) /* include a valid logical page num in the pte if the valid bit is set */
-#define H_READ_4 (1UL<<(63-26)) /* Return 4 PTEs */
-#define H_AVPN (1UL<<(63-32)) /* An avpn is provided as a sanity test */
-#define H_ANDCOND (1UL<<(63-33))
-#define H_ICACHE_INVALIDATE (1UL<<(63-40)) /* icbi, etc. (ignored for IO pages) */
-#define H_ICACHE_SYNCHRONIZE (1UL<<(63-41)) /* dcbst, icbi, etc (ignored for IO pages */
-#define H_ZERO_PAGE (1UL<<(63-48)) /* zero the page before mapping (ignored for IO pages) */
-#define H_COPY_PAGE (1UL<<(63-49))
-#define H_N (1UL<<(63-61))
-#define H_PP1 (1UL<<(63-62))
-#define H_PP2 (1UL<<(63-63))
-
-/* DABRX flags */
-#define H_DABRX_HYPERVISOR (1UL<<(63-61))
-#define H_DABRX_KERNEL (1UL<<(63-62))
-#define H_DABRX_USER (1UL<<(63-63))
-
-/* pSeries hypervisor opcodes */
-#define H_REMOVE 0x04
-#define H_ENTER 0x08
-#define H_READ 0x0c
-#define H_CLEAR_MOD 0x10
-#define H_CLEAR_REF 0x14
-#define H_PROTECT 0x18
-#define H_GET_TCE 0x1c
-#define H_PUT_TCE 0x20
-#define H_SET_SPRG0 0x24
-#define H_SET_DABR 0x28
-#define H_PAGE_INIT 0x2c
-#define H_SET_ASR 0x30
-#define H_ASR_ON 0x34
-#define H_ASR_OFF 0x38
-#define H_LOGICAL_CI_LOAD 0x3c
-#define H_LOGICAL_CI_STORE 0x40
-#define H_LOGICAL_CACHE_LOAD 0x44
-#define H_LOGICAL_CACHE_STORE 0x48
-#define H_LOGICAL_ICBI 0x4c
-#define H_LOGICAL_DCBF 0x50
-#define H_GET_TERM_CHAR 0x54
-#define H_PUT_TERM_CHAR 0x58
-#define H_REAL_TO_LOGICAL 0x5c
-#define H_HYPERVISOR_DATA 0x60
-#define H_EOI 0x64
-#define H_CPPR 0x68
-#define H_IPI 0x6c
-#define H_IPOLL 0x70
-#define H_XIRR 0x74
-#define H_PERFMON 0x7c
-#define H_MIGRATE_DMA 0x78
-#define H_REGISTER_VPA 0xDC
-#define H_CEDE 0xE0
-#define H_CONFER 0xE4
-#define H_PROD 0xE8
-#define H_GET_PPP 0xEC
-#define H_SET_PPP 0xF0
-#define H_PURR 0xF4
-#define H_PIC 0xF8
-#define H_REG_CRQ 0xFC
-#define H_FREE_CRQ 0x100
-#define H_VIO_SIGNAL 0x104
-#define H_SEND_CRQ 0x108
-#define H_COPY_RDMA 0x110
-#define H_SET_XDABR 0x134
-#define H_STUFF_TCE 0x138
-#define H_PUT_TCE_INDIRECT 0x13C
-#define H_VTERM_PARTNER_INFO 0x150
-#define H_REGISTER_VTERM 0x154
-#define H_FREE_VTERM 0x158
-#define H_POLL_PENDING 0x1D8
-
-#ifndef __ASSEMBLY__
-
-/* plpar_hcall() -- Generic call interface using above opcodes
- *
- * The actual call interface is a hypervisor call instruction with
- * the opcode in R3 and input args in R4-R7.
- * Status is returned in R3 with variable output values in R4-R11.
- * Only H_PTE_READ with H_READ_4 uses R6-R11 so we ignore it for now
- * and return only two out args which MUST ALWAYS BE PROVIDED.
- */
-long plpar_hcall(unsigned long opcode,
- unsigned long arg1,
- unsigned long arg2,
- unsigned long arg3,
- unsigned long arg4,
- unsigned long *out1,
- unsigned long *out2,
- unsigned long *out3);
-
-/* Same as plpar_hcall but for those opcodes that return no values
- * other than status. Slightly more efficient.
- */
-long plpar_hcall_norets(unsigned long opcode, ...);
-
-/*
- * Special hcall interface for ibmveth support.
- * Takes 8 input parms. Returns a rc and stores the
- * R4 return value in *out1.
- */
-long plpar_hcall_8arg_2ret(unsigned long opcode,
- unsigned long arg1,
- unsigned long arg2,
- unsigned long arg3,
- unsigned long arg4,
- unsigned long arg5,
- unsigned long arg6,
- unsigned long arg7,
- unsigned long arg8,
- unsigned long *out1);
-
-/* plpar_hcall_4out()
- *
- * same as plpar_hcall except with 4 output arguments.
- *
- */
-long plpar_hcall_4out(unsigned long opcode,
- unsigned long arg1,
- unsigned long arg2,
- unsigned long arg3,
- unsigned long arg4,
- unsigned long *out1,
- unsigned long *out2,
- unsigned long *out3,
- unsigned long *out4);
-
-#endif /* __ASSEMBLY__ */
-#endif /* _PPC64_HVCALL_H */
projects / karo-tx-linux.git / blobdiff