Florian Fainelli [Fri, 20 Jan 2017 19:08:27 +0000 (11:08 -0800)]
net: systemport: Add support for SYSTEMPORT Lite
Add supporf for the SYSTEMPORT Lite Ethernet controller, this piece of hardware
is largely based on the full-blown SYSTEMPORT and differs in the following:
- no full-blown UniMAC, instead we have the MagicPacket matching from UniMAC at
same offset, and a GMII Interface Block (GIB) for the MAC-level stuff, since
we are always interfaced to an Ethernet switch which is fully Ethernet compliant
shortcuts could be made
- 16 transmit queues, whose interrupts are moved into the first Level-2 interrupt
controller bank
- slight TDMA offset change (a register was inserted after TDMA_STATUS, *sigh*)
Florian Fainelli [Fri, 20 Jan 2017 19:08:26 +0000 (11:08 -0800)]
net: systemport: Dynamically allocate number of TX rings
In preparation for adding SYSTEMPORT Lite, which has twice as less transmit
queues than SYSTEMPORT make sure we do allocate TX rings based on the
systemport,txq property to get an appropriate memory footprint.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 20 Jan 2017 16:08:56 +0000 (08:08 -0800)]
ipv6: add NUMA awareness to seg6_hmac_init_algo()
Since we allocate per cpu storage, let's also use NUMA hints.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: David Lebrun <david.lebrun@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net>
jpinto [Fri, 20 Jan 2017 16:00:26 +0000 (16:00 +0000)]
net: stmicro: fix LS field mask in EEE configuration
This patch fixes the LS mask when setting EEE timer.
LS field is 10 bits long and not 11 as currently.
Signed-off-by: Joao Pinto <jpinto@synopsys.com> Reported-By: Rayagond Kokatanur <rayagond@vayavyalabs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Fri, 20 Jan 2017 14:36:57 +0000 (22:36 +0800)]
net/mlx4: use rb_entry()
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 19:42:52 +0000 (14:42 -0500)]
Merge branch 'dsa-hwmon'
Andrew Lunn says:
====================
net: dsa: Move temperature sensor code into PHY.
Marvell Ethernet switches contain a temperature sensor. There appears
to be one sensor, which is shared by each of the internal PHYs. Each
PHY has independent registers to read this sensor, and to set a limit
for when an alarm should be raised.
Some Marvell discrete PHY also have the same sensor and registers.
Moving the HWMON code from DSA into the PHY makes the sensor available
in discrete PHYs, and removes the layering violation, the switch
driver poking around in PHY registers.
While moving the code into the PHY driver, it has been re-written to
use the new HWMON APIs.
v2:
Better Cover note explaining one sensor, but multiple independent
registers
Simply error checking.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 20 Jan 2017 00:37:50 +0000 (01:37 +0100)]
net: dsa: Remove hwmon support
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Thu, 19 Jan 2017 22:47:46 +0000 (17:47 -0500)]
inet: don't use sk_v6_rcv_saddr directly
When comparing two sockets we need to use inet6_rcv_saddr so we get a NULL
sk_v6_rcv_saddr if the socket isn't AF_INET6, otherwise our comparison function
can be wrong.
Fixes: 637bc8b ("inet: reset tb->fastreuseport when adding a reuseport sk") Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 19:22:27 +0000 (14:22 -0500)]
Merge tag 'mlx5-updates-2017-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 and mlx5e updates 2017-01-19
This series includes some updates for mlx5 core and mlx5e netdevice driver.
From Leon, a small fix that remove an unnecessary print.
From Eli Cohen, a fix to the FW version printout in case of internal error.
From Eugenia Emantayev, two patches, the 1st adds mlx5 1pps (pulse per
second) mlx5 infrastructure support and the 2nd adds the necessary bits
for mlx5e ptp logic and structures.
From Mohamad, add support for s-tagged packet receive when in promiscuous
mode.
Form Gal Pressman, MCAM (Management capabilities mask register) and PCAM
(Ports capabilities mask register) registers infrastructure, those
registers are needed in order to query the different statistics registers
support in FW, in order for the driver to enable/disable query and
reporting them back to user. On top of this infrastructure we've exposed
new set of statistics groups:
- MPCNT: Physical layer statistical counters (For symbol errors)
- PPCNT: PCIe performance counters
In addition to the statistics capabilities series we've moved the mlx5 HCA
capabilities fields to a dedicated struct under the driver private data.
At the end a small patch to update & query statistics in the most desired
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 17:35:11 +0000 (12:35 -0500)]
Merge branch 'cpsw-common-res-usage'
Ivan Khoronzhuk says:
====================
net: ethernet: ti: cpsw: correct common res usage
This series is intended to remove unneeded redundancies connected with
common resource usage function.
Since v1:
- changed name to cpsw_get_usage_count()
- added comments to open/closw for cpsw_get_usage_count()
- added patch:
net: ethernet: ti: cpsw: clarify ethtool ops changing num of descs
Based on net-next/master
====================
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Thu, 19 Jan 2017 16:58:27 +0000 (18:58 +0200)]
net: ethernet: ti: cpsw: clarify ethtool ops changing num of descs
After adding cpsw_set_ringparam ethtool op, better to carry out
common parts of similar ops splitting descriptors in runtime. It
allows to reuse these parts and shows what the ops actually do.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Thu, 19 Jan 2017 16:58:24 +0000 (18:58 +0200)]
net: ethernet: ti: cpsw: don't disable interrupts in ndo_open
No need to disable interrupts if no open devices,
they are disabled anyway.
Even no need to disable interrupts if some ndev is opened, In this
case shared resources are not touched, only parameters of ndev shell,
so no reason to disable them also. Removed lines have proved it.
So, no need in redundant check and interrupt disable.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Thu, 19 Jan 2017 16:58:23 +0000 (18:58 +0200)]
net: ethernet: ti: cpsw: remove dual check from common res usage function
Common res usage is possible only in case an interface is
running. In case of not dual emac here can be only one interface,
so while ndo_open and switch mode, only one interface can be opened,
thus if open is called no any interface is running ... and no common
res are used. So remove check on dual emac, it will simplify
code/understanding and will match the name it's called.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 17:22:27 +0000 (12:22 -0500)]
Merge branch 'rxbusy'
Mahesh Bandewar says:
====================
use netdev_is_rx_handler_busy() in few known cases
netdev_rx_handler_register() was recently split into two parts - (a) check
if the handler is used, (b) register the new handler, parts. This is
helpful in scenarios like bonding where at the time of registration there
is too much state to unwind and it should check if the device is free
before building that state. IPvlan and macvlan drivers don't have this
issue however it can make use of the same check instead of using a device
specific check.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Wed, 18 Jan 2017 23:02:53 +0000 (15:02 -0800)]
ipvlan: use netdev_is_rx_handler_busy instead of checking specific type
IPvlan checks if the master device is already used by checking a
specific device (here it's macvlan device). This is technically not
sufficient and it should just ensure the rx_handler is busy or not.
This would be a super check that includes macvlan and any other that
has already registered rx-handler.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Wed, 18 Jan 2017 23:02:49 +0000 (15:02 -0800)]
net: remove duplicate code.
netdev_rx_handler_register() checks to see if the handler is already
busy which was recently separated into netdev_is_rx_handler_busy(). So
use the same function inside register() to avoid code duplication.
Essentially this change should be a no-op
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The fq_codel qdisc currently always regenerates the skb flow hash.
This wastes some cycles and prevents flow seperation in cases where
the traffic has been encrypted and can no longer be understood by the
flow dissector.
Change it to use the prexisting flow hash if one exists, and only
regenerate if necessary.
Signed-off-by: Andrew Collins <acollins@cradlepoint.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 17:10:17 +0000 (12:10 -0500)]
Merge branch 'tipc-multicast-through-replication'
Jon Maloy says:
====================
tipc: emulate multicast through replication
TIPC multicast messages are currently distributed via L2 broadcast
or IP multicast to all nodes in the cluster, irrespective of the
number of real destinations of the message.
In this series we introduce an option to transport messages via
replication ("replicast") across a selected number of unicast links,
instead of relying on the underlying media. This option is used when
true broadcast/multicast is not supported by the media, or when the
number of true destinations is much smaller than the cluster size.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:53 +0000 (13:50 -0500)]
tipc: make replicast a user selectable option
If the bearer carrying multicast messages supports broadcast, those
messages will be sent to all cluster nodes, irrespective of whether
these nodes host any actual destinations socket or not. This is clearly
wasteful if the cluster is large and there are only a few real
destinations for the message being sent.
In this commit we extend the eligibility of the newly introduced
"replicast" transmit option. We now make it possible for a user to
select which method he wants to be used, either as a mandatory setting
via setsockopt(), or as a relative setting where we let the broadcast
layer decide which method to use based on the ratio between cluster
size and the message's actual number of destination nodes.
In the latter case, a sending socket must stick to a previously
selected method until it enters an idle period of at least 5 seconds.
This eliminates the risk of message reordering caused by method change,
i.e., when changes to cluster size or number of destinations would
otherwise mandate a new method to be used.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:52 +0000 (13:50 -0500)]
tipc: introduce replicast as transport option for multicast
TIPC multicast messages are currently carried over a reliable
'broadcast link', making use of the underlying media's ability to
transport packets as L2 broadcast or IP multicast to all nodes in
the cluster.
When the used bearer is lacking that ability, we can instead emulate
the broadcast service by replicating and sending the packets over as
many unicast links as needed to reach all identified destinations.
We now introduce a new TIPC link-level 'replicast' service that does
this.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:51 +0000 (13:50 -0500)]
tipc: add functionality to lookup multicast destination nodes
As a further preparation for the upcoming 'replicast' functionality,
we add some necessary structs and functions for looking up and returning
a list of all nodes that host destinations for a given multicast message.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 18 Jan 2017 18:50:50 +0000 (13:50 -0500)]
tipc: add function for checking broadcast support in bearer
As a preparation for the 'replicast' functionality we are going to
introduce in the next commits, we need the broadcast base structure to
store whether bearer broadcast is available at all from the currently
used bearer or bearers.
We do this by adding a new function tipc_bearer_bcast_support() to
the bearer layer, and letting the bearer selection function in
bcast.c use this to give a new boolean field, 'bcast_support' the
appropriate value.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gianluca Borello [Wed, 18 Jan 2017 17:55:49 +0000 (17:55 +0000)]
bpf: add bpf_probe_read_str helper
Provide a simple helper with the same semantics of strncpy_from_unsafe():
int bpf_probe_read_str(void *dst, int size, const void *unsafe_addr)
This gives more flexibility to a bpf program. A typical use case is
intercepting a file name during sys_open(). The current approach is:
SEC("kprobe/sys_open")
void bpf_sys_open(struct pt_regs *ctx)
{
char buf[PATHLEN]; // PATHLEN is defined to 256
bpf_probe_read(buf, sizeof(buf), ctx->di);
/* consume buf */
}
This is suboptimal because the size of the string needs to be estimated
at compile time, causing more memory to be copied than often necessary,
and can become more problematic if further processing on buf is done,
for example by pushing it to userspace via bpf_perf_event_output(),
since the real length of the string is unknown and the entire buffer
must be copied (and defining an unrolled strnlen() inside the bpf
program is a very inefficient and unfeasible approach).
With the new helper, the code can easily operate on the actual string
length rather than the buffer size:
SEC("kprobe/sys_open")
void bpf_sys_open(struct pt_regs *ctx)
{
char buf[PATHLEN]; // PATHLEN is defined to 256
int res = bpf_probe_read_str(buf, sizeof(buf), ctx->di);
/* consume buf, for example push it to userspace via
* bpf_perf_event_output(), but this time we can use
* res (the string length) as event size, after checking
* its boundaries.
*/
}
Another useful use case is when parsing individual process arguments or
individual environment variables navigating current->mm->arg_start and
current->mm->env_start: using this helper and the return value, one can
quickly iterate at the right offset of the memory area.
The code changes simply leverage the already existent
strncpy_from_unsafe() kernel function, which is safe to be called from a
bpf program as it is used in bpf_trace_printk().
Signed-off-by: Gianluca Borello <g.borello@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Jan 2017 16:43:17 +0000 (11:43 -0500)]
Merge branch 'bus-agnostic-num-vf'
Phil Sutter says:
====================
Retrieve number of VFs in a bus-agnostic way
Previously, it was assumed that only PCI NICs would be capable of having
virtual functions - with my proposed enhancement of dummy NIC driver
implementing (fake) ones for testing purposes, this is no longer true.
Discussion of said patch has led to the suggestion of implementing a
bus-agnostic method for VF count retrieval so rtnetlink could work with
both real VF-capable PCI NICs as well as my dummy modifications without
introducing ugly hacks.
The following series tries to achieve just that by introducing a bus
type callback to retrieve a device's number of VFs, implementing this
callback for PCI bus and finally adjusting rtnetlink to make use of the
generalized infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Wed, 18 Jan 2017 13:04:39 +0000 (14:04 +0100)]
device: Implement a bus agnostic dev_num_vf routine
Now that pci_bus_type has num_vf callback set, dev_num_vf can be
implemented in a bus type independent way and the check for whether a
PCI device is being handled in rtnetlink can be dropped.
Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Fri, 20 Jan 2017 13:53:06 +0000 (14:53 +0100)]
gre6: Clean up unused struct ipv6_tel_txoption definition
Commit b05229f44228 ("gre6: Cleanup GREv6 transmit path, call common GRE
functions") removed the ip6gre specific transmit function, but left the
struct ipv6_tel_txoption definition. Clean it up.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 18 Jan 2017 14:52:51 +0000 (15:52 +0100)]
cxgb4: hide unused warnings
The two new variables are only used inside of an #ifdef and cause
harmless warnings when that is disabled:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'init_one':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:9: error: unused variable 'port_vec' [-Werror=unused-variable]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:6: error: unused variable 'v' [-Werror=unused-variable]
This adds another #ifdef around the declarations.
Fixes: 96fe11f27b70 ("cxgb4: Implement ndo_get_phys_port_id for mgmt dev") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Jan 2017 15:40:36 +0000 (07:40 -0800)]
net: ipv6: Keep nexthop of multipath route on admin down
IPv6 deletes route entries associated with multipath routes on an
admin down where IPv4 does not. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24 metric 64
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.100.2.254 dev eth2 weight 1
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.4
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Set link down:
$ ip li set eth1 down
IPv4 retains the multihop route but flags eth1 route as dead:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.16 dev eth1 weight 1 dead linkdown
nexthop via 10.100.2.16 dev eth2 weight 1
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
and IPv6 deletes the route as part of flushing all routes for the device:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Worse, on admin up of the device the multipath route has to be deleted
to get this leg of the route re-added.
This patch keeps routes that are part of a multipath route if
ignore_routes_with_linkdown is set with the dead and linkdown flags
enabling consistency between IPv4 and IPv6:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 dead linkdown pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 18 Jan 2017 04:14:10 +0000 (20:14 -0800)]
mlx4: support __GFP_MEMALLOC for rx
Commit 04aeb56a1732 ("net/mlx4_en: allocate non 0-order pages for RX
ring with __GFP_NOMEMALLOC") added code that appears to be not needed at
that time, since mlx4 never used __GFP_MEMALLOC allocations anyway.
As using memory reserves is a must in some situations (swap over NFS or
iSCSI), this patch adds this flag.
Note that this driver does not reuse pages (yet) so we do not have to
add anything else.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 529ed1275263 ("net: phy: phy drivers should not set
SUPPORTED_[Asym_]Pause"), phylib now handles automatically enabling
pause frame support in the PHY, and the MAC driver should follow suit.
Since the EMAC driver driver does this, we no longer need to force
pause frames support.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Tue, 23 Aug 2016 09:23:29 +0000 (12:23 +0300)]
net/mlx5e: Expose physical layer statistical counters to ethtool
Use ethtool -S to query physical layer statistical counters including:
- rx_symbol_errors_phy: Number of symbol errors that were not corrected
by FEC correction algorithm or that FEC was not active on this interface.
- rx_corrected_bits_phy: Number of corrected bits according to active
FEC (RS/FC).
Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman [Thu, 8 Dec 2016 14:03:31 +0000 (16:03 +0200)]
net/mlx5: Query and cache PCAM, MCAM registers on initialization
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PCAM and MCAM registers will provide information regarding firmware
support for different features, in order to avoid cases where new driver
combined with old firmware results in syndromes (for ex. PCIe counters
before this patchset).
Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5e: Receive s-tagged packets in promiscuous mode
Today when the driver enter to promiscuous mode or vlan
filter is disabled, we add flow rule to receive any c-taggd
packets, therefore s-tagged packets are dropped.
In order to receive s-tagged packets as well we need to add
flow rule to receive any s-tagged packet.
This patch enables the 1PPS IN and 1PPS OUT support according
to the advertised HCA capability. Single pin may be configured
to one of the above mutual exclusive functions via standard
Linux tools and APIs. For example, testptp open source application.
net/mlx5: Add MTPPS and MTPPSE registers infrastructure
Implement query and set functionality for MTPPS and MTPPSE registers.
MTPPS (Management Pulse Per Second) provides the device PPS capabilities,
configures the PPS in and out modules and holds the PPS in time stamp.
Query MTPPS is supported only when HCA_CAP.pps is set and modify is supported
when HCA_CAP.pps_modify is set.
MTPPSE (Management Pulse Per Second Event) configures the different event
generation modes for PPS. Supported when HCA_CAP.pps is set.
Eli Cohen [Fri, 16 Dec 2016 16:30:15 +0000 (10:30 -0600)]
net/mlx5: Fix version printout in case of health issue
Firmware representation of the firmware version on the health buffer has
changed for newer device. The representation in the initialization
segment does not and will not change. In addition, we print the health
buffer firmware version as a raw hex number.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Leon Romanovsky [Thu, 1 Dec 2016 08:34:57 +0000 (10:34 +0200)]
net/mlx5: Remove information print after attempt to load mlx5_ib module
Infiniband part of mlx5 driver can be compiled as a module
or as a part of bzImage (compiled in). In the second case,
the call to request_module will return an error -ENOENT.
It will cause to a misleading print "failed request module
on mlx5_ib".
This patch removes this print, In order to comply with mlx4.
Fixes: f66f049fb738 ("net/mlx5_core: Request the mlx5 IB module on driver load") Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some bus names are pretty long and do not fit into
17 chars. Increase therefore MII_BUS_ID_SIZE and
phy_fixup.bus_id to larger number. Now mii_bus.id
can host larger name.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com> Signed-off-by: Magnus Öberg <magnus.oberg@westermo.se> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
macb: Common code to enable ptp support for MACB/GEM
This patch does the following:
- MACB/GEM-PTP interface
- registers and bitfields for TSU
- capability flags to enable PTP per platform basis
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The new ARP support has pushed the stack size over the edge on ARM,
as there are two large objects on the stack in this function (mask
and tb) and both have now grown a bit more:
net/sched/cls_flower.c: In function 'fl_change':
net/sched/cls_flower.c:928:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
We can solve this by dynamically allocating one or both of them.
I first tried to do it just for the mask, but that only saved
152 bytes on ARM, while this version just does it for the 'tb'
array, bringing the stack size back down to 664 bytes.
Fixes: 99d31326cbe6 ("net/sched: cls_flower: Support matching on ARP") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 18 Jan 2017 16:45:01 +0000 (17:45 +0100)]
net: Remove usage of net_device last_rx member
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738376d ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f49b ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dacec ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Mirko Lindner <mlindner@marvell.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 18 Jan 2017 01:41:39 +0000 (20:41 -0500)]
net: dsa: use cpu_switch instead of ds[0]
Now that the DSA Ethernet switches are true Linux devices, the CPU
switch is not necessarily the first one. If its address is higher than
the second switch on the same MDIO bus, its index will be 1, not 0.
Avoid any confusion by using dst->cpu_switch instead of dst->ds[0].
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 18 Jan 2017 01:41:38 +0000 (20:41 -0500)]
net: dsa: store CPU switch structure in the tree
Store a dsa_switch pointer to the CPU switch in the tree instead of only
its index. This avoids the need to initialize it to -1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jan 2017 21:35:30 +0000 (16:35 -0500)]
Merge branch 'vhost_net-batching'
Jason Wang says:
====================
vhost_net tx batching
This series tries to implement tx batching support for vhost. This was
done by using MSG_MORE as a hint for under layer socket. The backend
(e.g tap) can then batch the packets temporarily in a list and
submit it all once the number of bacthed exceeds a limitation.
Tests shows obvious improvement on guest pktgen over over
mlx4(noqueue) on host:
Changes from V4:
- stick to NAPI_POLL_WEIGHT for rx-frames is user specify a value
greater than it.
Changes from V3:
- use ethtool instead of module parameter to control the maximum
number of batched packets
- avoid overhead when MSG_MORE were not set and no packet queued
Changes from V2:
- remove uselss queue limitation check (and we don't drop any packet now)
Changes from V1:
- drop NAPI handler since we don't use NAPI now
- fix the issues that may exceeds max pending of zerocopy
- more improvement on available buffer detection
- move the limitation of batched pacekts from vhost to tuntap
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 18 Jan 2017 07:02:03 +0000 (15:02 +0800)]
tun: rx batching
We can only process 1 packet at one time during sendmsg(). This often
lead bad cache utilization under heavy load. So this patch tries to do
some batching during rx before submitting them to host network
stack. This is done through accepting MSG_MORE as a hint from
sendmsg() caller, if it was set, batch the packet temporarily in a
linked list and submit them all once MSG_MORE were cleared.
Tests were done by pktgen (burst=128) in guest over mlx4(noqueue) on host:
User were allowed to change per device batched packets through
ethtool -C rx-frames. NAPI_POLL_WEIGHT were used as upper limitation
to prevent bh from being disabled too long.
Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 18 Jan 2017 07:02:02 +0000 (15:02 +0800)]
vhost_net: tx batching
This patch tries to utilize tuntap rx batching by peeking the tx
virtqueue during transmission, if there's more available buffers in
the virtqueue, set MSG_MORE flag for a hint for backend (e.g tuntap)
to batch the packets.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 18 Jan 2017 07:02:01 +0000 (15:02 +0800)]
vhost: better detection of available buffers
This patch tries to do several tweaks on vhost_vq_avail_empty() for a
better performance:
- check cached avail index first which could avoid userspace memory access.
- using unlikely() for the failure of userspace access
- check vq->last_avail_idx instead of cached avail index as the last
step.
This patch is need for batching supports which needs to peek whether
or not there's still available buffers in the ring.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Wed, 18 Jan 2017 00:50:05 +0000 (08:50 +0800)]
net:add one common config ARCH_WANT_RELAX_ORDER to support relax ordering
Relax ordering(RO) is one feature of 82599 NIC, to enable this feature can
enhance the performance for some cpu architecure, such as SPARC and so on.
Currently it only supports one special cpu architecture(SPARC) in 82599
driver to enable RO feature, this is not very common for other cpu architecture
which really needs RO feature.
This patch add one common config CONFIG_ARCH_WANT_RELAX_ORDER to set RO feature,
and should define CONFIG_ARCH_WANT_RELAX_ORDER in sparc Kconfig firstly.
Signed-off-by: Mao Wenan <maowenan@huawei.com> Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 17 Jan 2017 23:51:08 +0000 (15:51 -0800)]
net: ipv6: remove prefix arg to rt6_fill_node
The prefix arg to rt6_fill_node is non-0 in only 1 path - rt6_dump_route
where a user is requesting a prefix only dump. Simplify rt6_fill_node
by removing the prefix arg and moving the prefix check to rt6_dump_route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patch 6/6 is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525
section 5.1.2 and 5.1.3
Patches 1-5/6 are ahead of it to define some apis and asoc members
for it.
Note that with this patchset, asoc->reconf_enable has no chance yet to
be set, until the patch "sctp: add get and set sockopt for reconf_enable"
is applied in the future. As we can not just enable it when sctp is not
capable of processing reconf chunk yet.
v1->v2:
- put these into a smaller group.
- rename some temporary variables in the codes.
- rename the titles of the commits and improve some changelogs.
v2->v3:
- re-split the patchset and make sure it has no dead codes for review.
v3->v4:
- move sctp_make_reconf() into patch 1/6 to avoid kbuild warning.
- drop unused struct sctp_strreset_req.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:47 +0000 (00:44 +0800)]
sctp: implement sender-side procedures for SSN Reset Request Parameter
This patch is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525 section
5.1.2 and 5.1.3.
It is also add sockopt SCTP_RESET_STREAMS in rfc6525 section 6.3.2
for users.
Note that the new asoc member strreset_outstanding is to make sure
only one reconf request chunk on the fly as rfc6525 section 5.1.1
demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:46 +0000 (00:44 +0800)]
sctp: add sockopt SCTP_ENABLE_STREAM_RESET
This patch is to add sockopt SCTP_ENABLE_STREAM_RESET to get/set
strreset_enable to indicate which reconf request type it supports,
which is described in rfc6525 section 6.3.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:45 +0000 (00:44 +0800)]
sctp: add reconf_enable in asoc ep and netns
This patch is to add reconf_enable field in all of asoc ep and netns
to indicate if they support stream reset.
When initializing, asoc reconf_enable get the default value from ep
reconf_enable which is from netns netns reconf_enable by default.
It is also to add reconf_capable in asoc peer part to know if peer
supports reconf_enable, the value is set if ext params have reconf
chunk support when processing init chunk, just as rfc6525 section
5.1.1 demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:44 +0000 (00:44 +0800)]
sctp: add stream reconf primitive
This patch is to add a primitive based on sctp primitive frame for
sending stream reconf request. It works as the other primitives,
and create a SCTP_CMD_REPLY command to send the request chunk out.
sctp_primitive_RECONF would be the api to send a reconf request
chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:43 +0000 (00:44 +0800)]
sctp: add stream reconf timer
This patch is to add a per transport timer based on sctp timer frame
for stream reconf chunk retransmission. It would start after sending
a reconf request chunk, and stop after receiving the response chunk.
If the timer expires, besides retransmitting the reconf request chunk,
it would also do the same thing with data RTO timer. like to increase
the appropriate error counts, and perform threshold management, possibly
destroying the asoc if sctp retransmission thresholds are exceeded, just
as section 5.1.1 describes.
This patch is also to add asoc strreset_chunk, it is used to save the
reconf request chunk, so that it can be retransmitted, and to check if
the response is really for this request by comparing the information
inside with the response chunk as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 17 Jan 2017 16:44:42 +0000 (00:44 +0800)]
sctp: add support for generating stream reconf ssn reset request chunk
This patch is to add asoc strreset_outseq and strreset_inseq for
saving the reconf request sequence, initialize them when create
assoc and process init, and also to define Incoming and Outgoing
SSN Reset Request Parameter described in rfc6525 section 4.1 and
4.2, As they can be in one same chunk as section rfc6525 3.1-3
describes, it makes them in one function.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jan 2017 18:04:30 +0000 (13:04 -0500)]
Merge branch 'rework-inet_csk_get_port'
Josef Bacik says:
====================
Rework inet_csk_get_port
V3->V4:
-Removed the random include of addrconf.h that is no longer needed.
V2->V3:
-Dropped the fastsock from the tb and instead just carry the saddrs, family, and
ipv6 only flag.
-Reworked the helper functions to deal with this change so I could still use
them when checking the fast path.
-Killed tb->num_owners as per Eric's request.
-Attached a reproducer to the bottom of this email.
V1->V2:
-Added a new patch 'inet: collapse ipv4/v6 rcv_saddr_equal functions into one'
at Hannes' suggestion.
-Dropped ->bind_conflict and just use the new helper.
-Fixed a compile bug from the original ->bind_conflict patch.
The original description of the series follows:
At some point recently the guys working on our load balancer added the ability
to use SO_REUSEPORT. When they restarted their app with this option enabled
they immediately hit a softlockup on what appeared to be the
inet_bind_bucket->lock. Eventually what all of our debugging and discussion led
us to was the fact that the application comes up without SO_REUSEPORT, shuts
down which creates around 100k twsk's, and then comes up and tries to open a
bunch of sockets using SO_REUSEPORT, which meant traversing the inet_bind_bucket
owners list under the lock. Since this lock is needed for dealing with the
twsk's and basically anything else related to connections we would softlockup,
and sometimes not ever recover.
To solve this problem I did what you see in Path 5/5. Once we have a
SO_REUSEPORT socket on the tb->owners list we know that the socket has no
conflicts with any of the other sockets on that list. So we can add a copy of
the sock_common (really all we need is the recv_saddr but it seemed ugly to copy
just the ipv6, ipv4, and flag to indicate if we were ipv6 only in there so I've
copied the whole common) in order to check subsequent SO_REUSEPORT sockets. If
they match the previous one then we can skip the expensive
inet_csk_bind_conflict check. This is what eliminated the soft lockup that we
were seeing.
Patches 1-4 are cleanups and re-workings. For instance when we specify port ==
0 we need to find an open port, but we would do two passes through
inet_csk_bind_conflict every time we found a possible port. We would also keep
track of the smallest_port value in order to try and use it if we found no
port our first run through. This however made no sense as it would have had to
fail the first pass through inet_csk_bind_conflict, so would not actually pass
the second pass through either. Finally I split the function into two functions
in order to make it easier to read and to distinguish between the two behaviors.
I have tested this on one of our load balancing boxes during peak traffic and it
hasn't fallen over. But this is not my area, so obviously feel free to point
out where I'm being stupid and I'll get it fixed up and retested. Thanks,
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:06 +0000 (07:51 -0800)]
inet: reset tb->fastreuseport when adding a reuseport sk
If we have non reuseport sockets on a tb we will set tb->fastreuseport to 0 and
never set it again. Which means that in the future if we end up adding a bunch
of reuseport sk's to that tb we'll have to do the expensive scan every time.
Instead add the ipv4/ipv6 saddr fields to the bind bucket, as well as the family
so we know what comparison to make, and the ipv6 only setting so we can make
sure to compare with new sockets appropriately. Once one sk has made it onto
the list we know that there are no potential bind conflicts on the owners list
that match that sk's rcv_addr. So copy the sk's information into our bind
bucket and set tb->fastruseport to FASTREUSESOCK_STRICT so we know we have to do
an extra check for subsequent reuseport sockets and skip the expensive bind
conflict check.
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:05 +0000 (07:51 -0800)]
inet: split inet_csk_get_port into two functions
inet_csk_get_port does two different things, it either scans for an open port,
or it tries to see if the specified port is available for use. Since these two
operations have different rules and are basically independent lets split them
into two different functions to make them both more readable.
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:04 +0000 (07:51 -0800)]
inet: don't check for bind conflicts twice when searching for a port
This is just wasted time, we've already found a tb that doesn't have a bind
conflict, and we don't drop the head lock so scanning again isn't going to give
us a different answer. Instead move the tb->reuse setting logic outside of the
found_tb path and put it in the success: path. Then make it so that we don't
goto again if we find a bind conflict in the found_tb path as we won't reach
this anymore when we are scanning for an ephemeral port.
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:03 +0000 (07:51 -0800)]
inet: kill smallest_size and smallest_port
In inet_csk_get_port we seem to be using smallest_port to figure out where the
best place to look for a SO_REUSEPORT sk that matches with an existing set of
SO_REUSEPORT's. However if we get to the logic
if (smallest_size != -1) {
port = smallest_port;
goto have_port;
}
we will do a useless search, because we would have already done the
inet_csk_bind_conflict for that port and it would have returned 1, otherwise we
would have gone to found_tb and succeeded. Since this logic makes us do yet
another trip through inet_csk_bind_conflict for a port we know won't work just
delete this code and save us the time.
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:02 +0000 (07:51 -0800)]
inet: drop ->bind_conflict
The only difference between inet6_csk_bind_conflict and inet_csk_bind_conflict
is how they check the rcv_saddr, so delete this call back and simply
change inet_csk_bind_conflict to call inet_rcv_saddr_equal.
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Tue, 17 Jan 2017 15:51:01 +0000 (07:51 -0800)]
inet: collapse ipv4/v6 rcv_saddr_equal functions into one
We pass these per-protocol equal functions around in various places, but
we can just have one function that checks the sk->sk_family and then do
the right comparison function. I've also changed the ipv4 version to
not cast to inet_sock since it is unneeded.
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
jpinto [Tue, 17 Jan 2017 14:53:07 +0000 (14:53 +0000)]
stmicro: add more information to Kconfig
This patch adds more info to stmicro' Kconfig files in order to be clearer
that the driver can be used by ethernet cards based on 10/100/1000/EQOS
Synopsys IP Cores.
EQOS was also added stmmac/Kconfig Kconfig, since dwmac4 is in fact EQoS,
one of Synopsys Ethernet IPs. More info at:
https://www.synopsys.com/dw/ipdir.php?ds=dwc_ether_qos
Signed-off-by: Joao Pinto <jpinto@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 18 Jan 2017 06:06:07 +0000 (22:06 -0800)]
net/mlx5e: Support bpf_xdp_adjust_head()
This patch adds bpf_xdp_adjust_head() support to mlx5e.
1. rx_headroom is added to struct mlx5e_rq. It uses
an existing 4 byte hole in the struct.
2. The adjusted data length is checked against
MLX5E_XDP_MIN_INLINE and MLX5E_SW2HW_MTU(rq->netdev->mtu).
3. The macro MLX5E_SW2HW_MTU is moved from en_main.c to en.h.
MLX5E_HW2SW_MTU is also moved to en.h for symmetric reason
but it is not a must.
v2:
- Keep the xdp specific logic in mlx5e_xdp_handle()
- Update dma_len after the sanity checks in mlx5e_xmit_xdp_frame()
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Baron [Tue, 17 Jan 2017 18:37:19 +0000 (13:37 -0500)]
tcp: accept RST for rcv_nxt - 1 after receiving a FIN
Using a Mac OSX box as a client connecting to a Linux server, we have found
that when certain applications (such as 'ab'), are abruptly terminated
(via ^C), a FIN is sent followed by a RST packet on tcp connections. The
FIN is accepted by the Linux stack but the RST is sent with the same
sequence number as the FIN, and Linux responds with a challenge ACK per
RFC 5961. The OSX client then sometimes (they are rate-limited) does not
reply with any RST as would be expected on a closed socket.
This results in sockets accumulating on the Linux server left mostly in
the CLOSE_WAIT state, although LAST_ACK and CLOSING are also possible.
This sequence of events can tie up a lot of resources on the Linux server
since there may be a lot of data in write buffers at the time of the RST.
Accepting a RST equal to rcv_nxt - 1, after we have already successfully
processed a FIN, has made a significant difference for us in practice, by
freeing up unneeded resources in a more expedient fashion.
// Client closes the connection
0.300 < F. 1:1(0) ack 1 win 32768
// now send rst with same sequence
0.300 < R. 1:1(0) ack 1 win 32768
// make sure we are in TCP_CLOSE
0.400 %{
assert tcpi_state == 7
}%
Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shyam Saini [Tue, 17 Jan 2017 02:05:04 +0000 (07:35 +0530)]
qed: Replace memset with eth_zero_addr
Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero. Also, it makes the code clearer
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lance Richardson [Mon, 16 Jan 2017 23:11:35 +0000 (18:11 -0500)]
bridge: sparse fixes in br_ip6_multicast_alloc_query()
Changed type of csum field in struct igmpv3_query from __be16 to
__sum16 to eliminate type warning, made same change in struct
igmpv3_report for consistency.
Fixed up an ntohs() where htons() should have been used instead.
Signed-off-by: Lance Richardson <lrichard@redhat.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Jan 2017 19:38:44 +0000 (14:38 -0500)]
Merge branch 'mpls-packet-stats'
Robert Shearman says:
====================
mpls: Packet stats
This patchset records per-interface packet stats in the MPLS
forwarding path and exports them using a nest of attributes root at a
new IFLA_STATS_AF_SPEC attribute as part of RTM_GETSTATS messages:
The first patch adds the rtnl infrastructure for this, including a new
callbacks to per-AF ops of fill_stats_af and get_stats_af_size. The
second patch records MPLS stats and makes use of the infrastructure to
export them. The rtnl infrastructure could also be used to export IPv6
stats in the future.
Changes in v2:
- make incrementing IPv6 stats in mpls_stats_inc_outucastpkts
conditional on CONFIG_IPV6 to fix build with CONFIG_IPV6=n
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Mon, 16 Jan 2017 14:16:37 +0000 (14:16 +0000)]
mpls: Packet stats
Having MPLS packet stats is useful for observing network operation and
for diagnosing network problems. In the absence of anything better,
RFC2863 and RFC3813 are used for guidance for which stats to expose
and the semantics of them. In particular rx_noroutes maps to in
unknown protos in RFC2863. The stats are exposed to userspace via
AF_MPLS attributes embedded in the IFLA_STATS_AF_SPEC attribute of
RTM_GETSTATS messages.
All the introduced fields are 64-bit, even error ones, to ensure no
overflow with long uptimes. Per-CPU counters are used to avoid
cache-line contention on the commonly used fields. The other fields
have also been made per-CPU for code to avoid performance problems in
error conditions on the assumption that on some platforms the cost of
atomic operations could be more expensive than sending the packet
(which is what would be done in the success case). If that's not the
case, we could instead not use per-CPU counters for these fields.
Only unicast and non-fragment are exposed at the moment, but other
counters can be exposed in the future either by adding to the end of
struct mpls_link_stats or by additional netlink attributes in the
AF_MPLS IFLA_STATS_AF_SPEC nested attribute.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log