can: flexcan: enable interrupts atomically at the end of flexcan_chip_start()
This patch defers the writing of the interrupts bits of the CTRL register order
to enables all interrupts atomically at the the of the flexcan_chip_start()
function.
Suggested-by: Torsten Lang <torsten.lang@uweschneider.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: flexcan: use pointer to struct regs instead of void pointer for mmio address space
This patch renames the pointer to the mmio address space from "base" to "regs"
and changes the type from "void __iomem *" to "struct flexcan_regs __iomem *".
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames the "features" member of struct flexcan_devtype_data to
"quirks". The corresponding defines are renamed too, to reflect what they
actually do.
can: flexcan: flexcan_chip_start(): cleanup writing of reg_mcr
This patch changes the order the individual bits of the mcr register in
flexcan_chip_start() are or'ed together to match the datasheet. The inline
documentation is adjusted accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David S. Miller [Mon, 21 Sep 2015 05:26:58 +0000 (22:26 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-17
This series contains updates to i40e and i40evf.
Shannon provides updates to i40e and i40evf to resolve an issue with the
nvmupdate utility. First renames a variable name to reduce confusion and
to differentiate it from the actual user variable. Then added the ability
to save the admin queue write back descriptor if a caller supplies a
buffer for it to be saved into. Added a new GetStatus command so that
the NVM update tool can query the current status instead of doing fake
write requests to probe for readiness. Added wait states to the NVM
update state machine to signify when waiting for an update operation to
finish, whether we are in the middle of a set of write operations, or we
are now idle but waiting. Then added a facility to run admin queue
commands through the NVM update utility in order to allow the update
tools to interact with the firmware and do special commands needed for
updates and configuration changes. Also added a facility to recover the
result of a previously run admin queue command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace time_t type and get_seconds function which are not y2038 safe
on 32-bit systems. Function ktime_get_seconds use monotonic instead of
real time and therefore will not cause overflow.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Changes from V1:
1. Remove "inline" in C file (according to LKML comment, same in below).
2. Fix a bug about class_find_device.
3. Change the DTS pattern on hnae, restruct it to compatible with Hi1610 soc.
4. Unified hip04_mdio and hip05_mdio into hns_mdio, which is more usaul for
later SOCs.
net: add Hisilicon Network Subsystem basic ethernet support
This is to add basic ethernet support for HNS. It is one of the way to
use the HNS acceleration engine. But most of the decoding/encoding
capability of the AE cannot be used in this way.
This submit contains the basic feature as a ethernet driver. More will
be added later.
Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: Kenneth Lee <liguozhu@huawei.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
DSAF, namely Distributed System Area Fabric, is one of the HNS
acceleration engine implementation. This patch add DSAF driver to the
system.
hns_ae_adapt: the adaptor for registering the driver to HNAE framework
hns_dsaf_mac: MAC cover interface for GE and XGE
hns_dsaf_gmac: GE (10/100/1000G Ethernet) MAC function
hns_dsaf_xgmac: XGE (10000+G Ethernet) MAC function
hns_dsaf_main: the platform device driver for the whole hardware
hns_dsaf_misc: some misc helper function, such as LED support
hns_dsaf_ppe: packet process engine function
hns_dsaf_rcb: ring buffer function
Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: Kenneth Lee <liguozhu@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: add Hisilicon Network Subsystem hnae framework support
HNAE (Hisilicon Network Acceleration Engine) is a framework to provide a
unified ring buffer interface for Hisilicon Network Acceleration
Engines.
With the interface, upper layer can work as ethernet driver, ODP driver
or other service driver on purpose.
Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: Kenneth Lee <liguozhu@huawei.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO support for Hisilicon Network Subsystem. It is used in Hislicon
hip04, hip05 and Hi1610 SoC to control the external PHY
Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: Kenneth Lee <liguozhu@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: add Hisilicon Network Subsystem support (config and documents)
The Hisilicon Network Subsystem is a long term evolution IP which is
supposed to be used in Hisilicon ICT SoC. The IP, which is called hns
for short, is a TCP/IP acceleration engine, which can directly decode
TCP/IP stream and distribute them to different ring buffers.
HNS can be configured to work on different mode for different scenario.
This patch make use only some of the mode to make it as standard
ethernet NIC. The other mode will be added soon.
The whole function has 4 kernel sub-modules:
hnae: the HNS acceleration engine framework. It provides a abstract
interface between the engine and the upper layers which make use of the
engine by ring buffer.
hns_enet_drv: a standard ethernet driver that base on the ring buffer.
hns_dsaf: one of the implementation of HNS acceleration engine, which is
applied on Hililicon hip05, Hi1610 and other later-on SoCs
hns_mdio: the mdio control to the PHY, used by acceleration engine
This submit add basic config and documents
Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: Kenneth Lee <liguozhu@huawei.com> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
chas williams [Wed, 16 Sep 2015 20:28:25 +0000 (16:28 -0400)]
xen-netfront: always set num queues if possible
If netfront connects with two (or more) queues and then reconnects with
only one queue it fails to delete or rewrite the multi-queue-num-queues
key and netback will try to use the wrong number of queues.
Always write the num-queues field if the backend has multi-queue support.
Signed-off-by: Chas Williams <3chas3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bcmgenet: Implement RX coalescing control knobs
Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.
We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bcmgenet: Implement TX coalescing control knobs
Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.
We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.
Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.
While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Nikolay for noticing the uninitialized use amongst the maze of
gotos.
As Nikolay pointed out the second initialization is not required to fix
the oops, but rather to fix a related problem where a valid lookup should
be invalidated before creating the rth entry.
Fixes: b7503e0cdb5d ("net: Add FIB table id to rtable") Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Reported-by: Richard Alpe <richard.alpe@ericsson.com> Reported-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
At plumbers we discussed different options on how to get rid of skb_clone
from bpf_clone_redirect(), the patch 2 implements the best option.
Patch 1 adds 'integrated exts' to cls_bpf to improve performance by
combining simple actions into bpf classifier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing bpf_clone_redirect() helper clones skb before redirecting
it to RX or TX of destination netdev.
Introduce bpf_redirect() helper that does that without cloning.
Benchmarked with two hosts using 10G ixgbe NICs.
One host is doing line rate pktgen.
Another host is configured as:
$ tc qdisc add dev $dev ingress
$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
action bpf run object-file tcbpf1_kern.o section clone_redirect_xmit drop
so it receives the packet on $dev and immediately xmits it on $dev + 1
The section 'clone_redirect_xmit' in tcbpf1_kern.o file has the program
that does bpf_clone_redirect() and performance is 2.0 Mpps
$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
action bpf run object-file tcbpf1_kern.o section redirect_xmit drop
which is using bpf_redirect() - 2.4 Mpps
and using cls_bpf with integrated actions as:
$ tc filter add dev $dev root pref 10 \
bpf run object-file tcbpf1_kern.o section redirect_xmit integ_act classid 1
performance is 2.5 Mpps
To summarize:
u32+act_bpf using clone_redirect - 2.0 Mpps
u32+act_bpf using redirect - 2.4 Mpps
cls_bpf using redirect - 2.5 Mpps
For comparison linux bridge in this setup is doing 2.1 Mpps
and ixgbe rx + drop in ip_rcv - 7.8 Mpps
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 16 Sep 2015 06:05:42 +0000 (23:05 -0700)]
cls_bpf: introduce integrated actions
Often cls_bpf classifier is used with single action drop attached.
Optimize this use case and let cls_bpf return both classid and action.
For backwards compatibility reasons enable this feature under
TCA_BPF_FLAG_ACT_DIRECT flag.
Then more interesting programs like the following are easier to write:
int cls_bpf_prog(struct __sk_buff *skb)
{
/* classify arp, ip, ipv6 into different traffic classes
* and drop all other packets
*/
switch (skb->protocol) {
case htons(ETH_P_ARP):
skb->tc_classid = 1;
break;
case htons(ETH_P_IP):
skb->tc_classid = 2;
break;
case htons(ETH_P_IPV6):
skb->tc_classid = 3;
break;
default:
return TC_ACT_SHOT;
}
return TC_ACT_OK;
}
Joint work with Daniel Borkmann.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <tom@herbertland.com> Cc: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 15 Sep 2015 22:24:20 +0000 (15:24 -0700)]
tcp: provide skb->hash to synack packets
In commit b73c3d0e4f0e ("net: Save TX flow hash in sock and set in skbuf
on xmit"), Tom provided a l4 hash to most outgoing TCP packets.
We'd like to provide one as well for SYNACK packets, so that all packets
of a given flow share same txhash, to later enable bonding driver to
also use skb->hash to perform slave selection.
Note that a SYNACK retransmit shuffles the tx hash, as Tom did
in commit 265f94ff54d62 ("net: Recompute sk_txhash on negative routing
advice") for established sockets.
This has nice effect making TCP flows resilient to some kind of black
holes, even at connection establish phase.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <tom@herbertland.com> Cc: Mahesh Bandewar <maheshb@google.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Fri, 28 Aug 2015 21:55:51 +0000 (17:55 -0400)]
i40e/i40evf: add get AQ result command to nvmupdate utility
Add a facility to recover the result of a previously run AQ command.
Change-ID: I21afec2c20c1a5e6ba60c7fbfcbedfff78c10e45 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Fri, 28 Aug 2015 21:55:50 +0000 (17:55 -0400)]
i40e/i40evf: add exec_aq command to nvmupdate utility
Add a facility to run AQ commands through the nvmupdate utility in order
to allow the update tools to interact with the FW and do special
commands needed for updates and configuration changes.
Change-ID: I5c41523e4055b37f8e4ee479f7a0574368f4a588 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Fri, 28 Aug 2015 21:55:49 +0000 (17:55 -0400)]
i40e/i40evf: add wait states to NVM state machine
This adds wait states to the NVM update state machine to signify when
waiting for an update operation to finish, whether we're in the middle
of a set of Write operations, or we're now idle but waiting.
Change-ID: Iabe91d6579ef6a2ea560647e374035656211ab43 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Fri, 28 Aug 2015 21:55:48 +0000 (17:55 -0400)]
i40e/i40evf: add GetStatus command for nvmupdate
This adds a new GetStatus command so that the NVM update tool can query
the current status instead of doing fake write requests to probe for
readiness.
Change-ID: I671ec6ccd4dfc9dbac3a03b964589d693fda5cd8 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Fri, 28 Aug 2015 21:55:47 +0000 (17:55 -0400)]
i40e/i40evf: add handling of writeback descriptor
If the writeback descriptor buffer was previously created, this gives it
to the AQ command request to be used to save the results.
Change-ID: I8c8a1af81e6ebed6d0a15ed31697fe1a6c4e3708 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Thu, 27 Aug 2015 15:42:42 +0000 (11:42 -0400)]
i40e/i40evf: save aq writeback for future inspection
Add the ability to save the AdminQ write back descriptor if a
caller supplies a buffer for it to be saved into.
Change-ID: I3d1301d26360b39a2d66dc8569e851f54133a3af Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Thu, 23 Jul 2015 20:54:33 +0000 (16:54 -0400)]
i40e: rename variable to prevent clash of understanding
This code returns something that becomes the errno value from ethtool and
passes around a pointer to an errno variable. This patch changes the name
slightly to differentiate it from the actual user errno variable.
Change-ID: Idaa37845c069e66f4cea072e90f471bb2142454d Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Fri, 18 Sep 2015 00:18:38 +0000 (17:18 -0700)]
Merge branch 'nf_hook_netns'
Eric W. Biederman says:
====================
Passing net through the netfilter hooks
My primary goal with this patchset and it's follow ups is to cleanup the
network routing paths so that we do not look at the output device to
derive the network namespace. My plan is to pass the network namespace
of the transmitting socket through the output path, to replace code that
looks at the output network device today. Once that is done we can have
routes with output devices outside of the current network namespace.
Which should allow reception and transmission of packets in network
namespaces to be as fast as normal packet reception and transmission
with early demux disabled, because it will same code path.
Once skb_dst(skb)->dev is a little better under control I think it will
also be possible to use rcu to cleanup the ancient hack that sets
dst->dev to loopback_dev when a network device is removed.
The work to get there is a series of code cleanups. I am starting with
passing net into the netfilter hooks and into the functions that are
called after the netfilter hooks. This removes from netfilter the
need to guess which network namespace it is working on.
To get there I perform a series of minor prep patches so the big changes
at the end are possible to audit without getting lost in the noise. In
particular I have a lot of patches computing net into a local variable
and then using it through out the function.
So this patchset encompases removing dead code, sorting out the _sk
functions that were added last time someone pushed a prototype change
through the post netfilter functions. Cleaning up individual functions
use of the network namespace. Passing net into the netfilter hooks.
Passing net into the post netfilter functions. Using state->net in
the netfilter code where it is available and trivially usable.
Pablo, Dave I don't know whose tree this makes more sense to go
through. I am assuming at least initially Pablos as netfilter is
involved. From what I have seen there will be a lot of back and forth
between the netfilter code paths and the routing code paths.
The patches are also available (against 4.3-rc1) at:
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/net-next.git master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: Add blank lines in callers of netfilter hooks
In code review it was noticed that I had failed to add some blank lines
in places where they are customarily used. Taking a second look at the
code I have to agree blank lines would be nice so I have added them
here.
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is immediately motivated by the bridge code that chains functions that
call into netfilter. Without passing net into the okfns the bridge code would
need to guess about the best expression for the network namespace to process
packets in.
As net is frequently one of the first things computed in continuation functions
after netfilter has done it's job passing in the desired network namespace is in
many cases a code simplification.
To support this change the function dst_output_okfn is introduced to
simplify passing dst_output as an okfn. For the moment dst_output_okfn
just silently drops the struct net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of saying "net = dev_net(state->in?state->in:state->out)"
just say "state->net". As that information is now availabe,
much less confusing and much less error prone.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: Pass struct net into the netfilter hooks
Pass a network namespace parameter into the netfilter hooks. At the
call site of the netfilter hooks the path a packet is taking through
the network stack is well known which allows the network namespace to
be easily and reliabily.
This allows the replacement of magic code like
"dev_net(state->in?:state->out)" that appears at the start of most
netfilter hooks with "state->net".
In almost all cases the network namespace passed in is derived
from the first network device passed in, guaranteeing those
paths will not see any changes in practice.
The exceptions are:
xfrm/xfrm_output.c:xfrm_output_resume() xs_net(skb_dst(skb)->xfrm)
ipvs/ip_vs_xmit.c:ip_vs_nat_send_or_cont() ip_vs_conn_net(cp)
ipvs/ip_vs_xmit.c:ip_vs_send_or_cont() ip_vs_conn_net(cp)
ipv4/raw.c:raw_send_hdrinc() sock_net(sk)
ipv6/ip6_output.c:ip6_xmit() sock_net(sk)
ipv6/ndisc.c:ndisc_send_skb() dev_net(skb->dev) not dev_net(dst->dev)
ipv6/raw.c:raw6_send_hdrinc() sock_net(sk)
br_netfilter_hooks.c:br_nf_pre_routing_finish() dev_net(skb->dev) before skb->dev is set to nf_bridge->physindev
In all cases these exceptions seem to be a better expression for the
network namespace the packet is being processed in then the historic
"dev_net(in?in:out)". I am documenting them in case something odd
pops up and someone starts trying to track down what happened.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When struct net starts being passed through the ipv4 and ipv6 fragment
routines br_nf_push_frag_xmit will need to take a net parameter.
Prepare br_nf_push_frag_xmit before that is needed and introduce
br_nf_push_frag_xmit_sk for the call sites that still need the old
calling conventions.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is a prep work for passing struct net through ip_do_fragment and
later the netfilter okfn. Doing this independently makes the later
code changes clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A function with weird arguments that it will never use to accomdate a
netfilter callback prototype is absolutely in the core of the
networking stack. Frankly it does not make sense and it causes a lot
of confusion as to why arguments that are never used are being passed
to the function.
As I am preparing to make a second change to arguments to the okfn even
the names stops making sense.
As I have removed the two callers of this function remove this confusion
from the networking stack.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function dev_queue_xmit_skb_sk is unncessary and very confusing.
Introduce br_send_bpdu_finish to remove the need for dev_queue_xmit_skb_sk,
and have br_send_bpdu_finish call dev_queue_xmit.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function dev_queue_xmit_skb_sk is unncessary and very confusing.
Introduce arp_xmit_finish to remove the need for dev_queue_xmit_skb_sk,
and have arp_xmit_finish call dev_queue_xmit.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sock paramter to dst_output making dst_output_sk superfluous.
Add a skb->sk parameter to all of the callers of dst_output
Have the callers of dst_output_sk call dst_output.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 17 Sep 2015 23:50:36 +0000 (16:50 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-15
This series contains updates to ixgbe and fm10k.
Don fixes a ixgbe issue by adding checks for systems that do not have
SFP's to avoid incorrectly acting on interrupts that are falsely
interpreted as SFP events.
Alex Williamson adds a fix for ixgbe to disable SR-IOV prior to
unregistering the netdev to avoid issues with guest OS's which do not
support hot-unplug or their hot-unplug is broken.
Alex Duyck update the lowest limit for adaptive interrupt interrupt
moderation to about 12K interrupts per second for ixgbe. This change
increases the performance for ixgbe. Also fixed up fm10k to remove
the optimization that assumed that all fragments would be limited to
page size, since that assumption is incorrect as the TCP allocator can
provide up to a 32K page fragment. Updated fm10k to add the MAC
address to the list of values recorded on driver load. Fixes fm10k
so that we only trigger the data path reset if the fabric is ready to
handle traffic to avoid triggering the reset unless the switch API is
ready for us.
Jacob updates the fm10k driver to disable the service task during
suspend and re-enable it after we resume. If we don't do this, the
device could be UP when you suspend and come back from resume as
DOWN. Also update fm10k to prevent the removal of default VID rules,
and correctly remove the stack layers information of the VLAN, but then
return to forwarding that VID as untagged frames. If we deleted the VID
rules here, we would begin dropping traffic due to VLAN membership
violations. Fixed fm10k to use pcie_get_minimum_link(), which is useful
in cases where we connect to a slot at Gen3, but the slot is behind a bus
which is only connected at Gen2. Updated fm10k to update the netdev
permanent address during reinit instead of up to enable users to
immediately see the new MAC address on the VF even if the device is not
up. Adds the creation of VLAN interfaces on a device, even while the
device is down for fm10k. Fixed an issue where we request the incorrect
MAC/VLAN combinations, and prevents us from accidentally reporting some
frames as VLAN tagged. Provided a couple of trivial fixes for fm10k
to fix code style and typos in code comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 822b3b2ebfff8e9b3d006086c527738a7ca00cd0 ("net: Add max rate tx queue
attribute") moved get_netdev_queue_index around, but kept the old version.
Probably because of a reuse of the original patch from before Eric's change to
that function.
Remove one inline keyword, and no need for a loop to find
an index into a table.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Fixes: 822b3b2ebfff ("net: Add max rate tx queue attribute") Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
can: Allwinner A10/A20 CAN Controller support - Kernel module
Kernel module for Allwinner A10/A20 CAN controller.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: Allwinner A10/A20 CAN Controller support - Devicetree bindings
Devicetree bindings for Allwinner A10/A20 CAN controller.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Robert Jarzmik [Thu, 10 Sep 2015 19:26:04 +0000 (21:26 +0200)]
net: smc91x: convert pxa dma to dmaengine
Convert the dma transfers to be dmaengine based, now pxa has a dmaengine
slave driver. This makes this driver a bit more PXA agnostic.
The driver was tested on pxa27x (mainstone) and pxa310 (zylonite),
ie. only pxa platforms.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Russell King <linux@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Wed, 24 Jun 2015 20:34:50 +0000 (13:34 -0700)]
fm10k: fix iov_msg_mac_vlan_pf VID checks
The VF will send a message to request multicast addresses with the
default VID. In the current code, if the PF has statically assigned a
VLAN to a VF, then the VF will not get the multicast addresses. Fix up
all of the various VLAN messages to use identical checks (since each
check was different). Also use set as a variable, so that it simplifies
our check for whether VLAN matches the pf_vid.
The new logic will allow set of a VLAN if it is zero, automatically
converting to the default VID. Otherwise it will allow setting the PF
VID, or any VLAN if PF has not statically assigned a VLAN. This is
consistent behavior, and allows VF to request either 0 or the
default_vid without silently failing.
Note that we need the check for zero since VFs might not get the default
VID message in time to actually request non-zero VLANs.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 24 Jun 2015 20:34:49 +0000 (13:34 -0700)]
fm10k: Only trigger data path reset if fabric is up
This change makes it so that we only trigger the data path reset if the
fabric is ready to handle traffic. The general idea is to avoid
triggering the reset unless the switch API is ready for us. Otherwise
we can just postpone the reset until we receive a switch ready
notification.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 24 Jun 2015 20:34:48 +0000 (13:34 -0700)]
fm10k: re-enable VF after a full reset on detection of a Malicious event
Modify behavior of Malicious Driver Detection events. Presently, the
hardware disables the VF queues and re-assigns them to the PF. This
causes the VF in question to continuously Tx hang, because it assumes
that it can transmit over the queues in question. For transient events,
this results in continuous logging of malicious events.
New behavior is to reset the LPORT and VF state, so that the VF will
have to reset and re-enable itself. This does mean that malicious VFs
will possibly be able to continue and attempt malicious events again.
However, it is expected that system administrators will step in and
manually remove or disable the VF in question.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 24 Jun 2015 20:34:46 +0000 (13:34 -0700)]
fm10k: send traffic on default VID to VLAN device if we have one
This patch ensures that VLAN traffic on the default VID will go to the
corresponding VLAN device if it exists. To do this, mask the rx_ring VID
if we have an active VLAN on that VID.
For this to work correctly, we need to update fm10k_process_skb_fields
to correctly mask off the VLAN_PRIO_MASK bits and compare them
separately, otherwise we incorrectly compare the priority bits with the
cleared flag. This also happens to fix a related bug where having
priority bits set causes us to incorrectly classify traffic.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 24 Jun 2015 20:34:44 +0000 (13:34 -0700)]
fm10k: TRIVIAL fix up ordering of __always_unused and style
Fix some style issues in debugfs code, and correct ordering of void and
__always_unused. Technically, the order does not matter, but preferred
style is to put the macro between the type and name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Fri, 19 Jun 2015 17:56:10 +0000 (10:56 -0700)]
fm10k: don't store sw_vid at reset
If we store the sw_vid at reset of PF, then we accidentally prevent the
VF from receiving the message to update its default VID. This only
occurs if the VF is created before the PF has come up, which is the
standard way of creating VFs when using the module parameter.
This fixes an issue where we request the incorrect MAC/VLAN
combinations, and prevents us from accidentally reporting some frames as
VLAN tagged.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Fri, 19 Jun 2015 17:56:09 +0000 (10:56 -0700)]
fm10k: allow creation of VLAN interfaces even while down
We re-sync upon going up, so there is little reason to worry about not
syncing immediately with switch. This prevents an error that occurs if
you add a VLAN interface while down.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 19 Jun 2015 02:41:10 +0000 (19:41 -0700)]
fm10k: Report MAC address on driver load
This change adds the MAC address to the list of values recorded on driver
load. The MAC address represents the serial number of the unit and allows
us to track the value should a card be replaced in a system.
The log message should now be similar in output to that of ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 16 Jun 2015 18:47:12 +0000 (11:47 -0700)]
fm10k: Don't assume page fragments are page size
This change pulls out the optimization that assumed that all fragments
would be limited to page size. That hasn't been the case for some time now
and to assume this is incorrect as the TCP allocator can provide up to a
32K page fragment.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 15 Jun 2015 22:00:56 +0000 (15:00 -0700)]
fm10k: update netdev perm_addr during reinit, instead of at up
Update the netdev permanent address during fm10k_reinit enables the user
to immediately see the new MAC address on the VF even if the device
isn't up. The previous code required that the device by opened before
changes would appear.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 15 Jun 2015 22:00:55 +0000 (15:00 -0700)]
fm10k: update fm10k_slot_warn to use pcie_get_minimum link
This is useful in cases where we connect to a slot at Gen3, but the slot
is behind a bus which only connected at Gen2. This generally only
happens when a PCIe switch is in the sequence of devices, and can be
very confusing when you see slow performance with no obvious cause.
I am aware this patch has a few lines that break 80 characters, but
there does not seem to be a readable way to format them to less than 80
characters. Suggestions welcome.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 15 Jun 2015 22:00:53 +0000 (15:00 -0700)]
fm10k: only prevent removal of default VID rules
This allows us to correctly add a VLAN even if it matches our default
VID. However, we don't want to remove the VID rules once that VLAN is
deleted. Correctly remove the stack layers information of the VLAN, but
then return to forwarding that VID as untagged frames. If we deleted the
VID rules here, we would begin dropping traffic due to VLAN membership
violations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 15 Jun 2015 22:00:51 +0000 (15:00 -0700)]
fm10k: disable service task during suspend
The service task reads some registers as part of its normal routine,
even while the interface is down. Normally this is ok. However, during
suspend we have disabled the PCI device. Due to this, registers will
read in the same way as a surprise-remove event. Disable the service
task while we suspend, and re-enable it after we resume. If we don't do
this, the device could be UP when you suspend and come back from resume
as closed (since fm10k closes the device when it gets a surprise
remove).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 30 Jul 2015 22:19:28 +0000 (15:19 -0700)]
ixgbe: Limit lowest interrupt rate for adaptive interrupt moderation to 12K
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
Alex Williamson [Wed, 29 Jul 2015 20:38:21 +0000 (14:38 -0600)]
ixgbe: Teardown SR-IOV before unregister_netdev()
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 2 Sep 2015 20:47:54 +0000 (13:47 -0700)]
ixgbe: fix issue with SFP events with new X550 devices
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / karo-tx-linux.git / log