#
-# (C) Copyright 2000 - 2011
+# (C) Copyright 2000 - 2012
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
XWAY SoCs for booting from NOR flash. The U-Boot image needs to
be swapped if a flash programmer is used.
+- ARM options:
+ CONFIG_SYS_EXCEPTION_VECTORS_HIGH
+
+ Select high exception vectors of the ARM core, e.g., do not
+ clear the V bit of the c1 register of CP15.
+
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
CONFIG_CFB_CONSOLE
Enables console device for a color framebuffer. Needs following
- defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
+ defines (cf. smiLynxEM, i8042)
VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
(default big endian)
VIDEO_HW_RECTFILL graphic chip supports
'Sane' compilers will generate smaller code if
CONFIG_PRE_CON_BUF_SZ is a power of 2
+- Safe printf() functions
+ Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
+ the printf() functions. These are defined in
+ include/vsprintf.h and include snprintf(), vsnprintf() and
+ so on. Code size increase is approximately 300-500 bytes.
+ If this option is not given then these functions will
+ silently discard their buffer size argument - this means
+ you are not getting any overflow checking in this case.
+
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
+ CONFIG_CMD_SF * Read/write/erase SPI NOR flash
CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
If this defined, the driver is quiet.
The driver doen't show link status messages.
+ CONFIG_CALXEDA_XGMAC
+ Support for the Calxeda XGMAC device
+
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
for your device
- CONFIG_USBD_PRODUCTID 0xFFFF
+- ULPI Layer Support:
+ The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
+ the generic ULPI layer. The generic layer accesses the ULPI PHY
+ via the platform viewport, so you need both the genric layer and
+ the viewport enabled. Currently only Chipidea/ARC based
+ viewport is supported.
+ To enable the ULPI layer support, define CONFIG_USB_ULPI and
+ CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
- MMC Support:
The MMC controller on the Intel PXA is supported. To
- FAT(File Allocation Table) filesystem write function support:
CONFIG_FAT_WRITE
- Support for saving memory data as a file
- in FAT formatted partition
+
+ Define this to enable support for saving memory data as a
+ file in FAT formatted partition.
+
+ This will also enable the command "fatwrite" enabling the
+ user to write files to FAT.
- Keyboard Support:
CONFIG_ISA_KEYBOARD
allows to read/write in Dataflash via the standard
commands cp, md...
+- Serial Flash support
+ CONFIG_CMD_SF
+
+ Defining this option enables SPI flash commands
+ 'sf probe/read/write/erase/update'.
+
+ Usage requires an initial 'probe' to define the serial
+ flash parameters, followed by read/write/erase/update
+ commands.
+
+ The following defaults may be provided by the platform
+ to handle the common case when only a single serial
+ flash is present on the system.
+
+ CONFIG_SF_DEFAULT_BUS Bus identifier
+ CONFIG_SF_DEFAULT_CS Chip-select
+ CONFIG_SF_DEFAULT_MODE (see include/spi.h)
+ CONFIG_SF_DEFAULT_SPEED in Hz
+
- SystemACE Support:
CONFIG_SYSTEMACE
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:
+- Detailed boot stage timing
+ CONFIG_BOOTSTAGE
+ Define this option to get detailed timing of each stage
+ of the boot process.
+
+ CONFIG_BOOTSTAGE_USER_COUNT
+ This is the number of available user bootstage records.
+ Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
+ a new ID will be allocated from this stash. If you exceed
+ the limit, recording will stop.
+
+ CONFIG_BOOTSTAGE_REPORT
+ Define this to print a report before boot, similar to this:
+
+ Timer summary in microseconds:
+ Mark Elapsed Stage
+ 0 0 reset
+ 3,575,678 3,575,678 board_init_f start
+ 3,575,695 17 arch_cpu_init A9
+ 3,575,777 82 arch_cpu_init done
+ 3,659,598 83,821 board_init_r start
+ 3,910,375 250,777 main_loop
+ 29,916,167 26,005,792 bootm_start
+ 30,361,327 445,160 start_kernel
+
Legacy uImage format:
Arg Where When
fdt_high - if set this restricts the maximum address that the
flattened device tree will be copied into upon boot.
+ For example, if you have a system with 1 GB memory
+ at physical address 0x10000000, while Linux kernel
+ only recognizes the first 704 MB as low memory, you
+ may need to set fdt_high as 0x3C000000 to have the
+ device tree blob be copied to the maximum address
+ of the 704 MB low memory, so that Linux kernel can
+ access it during the boot procedure.
+
If this is set to the special value 0xFFFFFFFF then
the fdt will not be copied at all on boot. For this
to work it must reside in writable memory, have
projects / karo-tx-uboot.git / blobdiff