]> git.kernelconcepts.de Git - karo-tx-uboot.git/blobdiff - README
sandbox: Add a simple sound driver
[karo-tx-uboot.git] / README
diff --git a/README b/README
index 3fdd1197aa8fc8a223fe5c3cb3939f5ba6891048..216f0c70aa9403534127dcd256627fa55e12f08e 100644 (file)
--- a/README
+++ b/README
@@ -486,6 +486,22 @@ The following options need to be configured:
                PBI commands can be used to configure SoC before it starts the execution.
                Please refer doc/README.pblimage for more details
 
+               CONFIG_SYS_FSL_DDR_BE
+               Defines the DDR controller register space as Big Endian
+
+               CONFIG_SYS_FSL_DDR_LE
+               Defines the DDR controller register space as Little Endian
+
+               CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
+               Physical address from the view of DDR controllers. It is the
+               same as CONFIG_SYS_DDR_SDRAM_BASE for  all Power SoCs. But
+               it could be different for ARM SoCs.
+
+               CONFIG_SYS_FSL_DDR_INTLV_256B
+               DDR controller interleaving on 256-byte. This is a special
+               interleaving mode, handled by Dickens for Freescale layerscape
+               SoCs with ARM core.
+
 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 
@@ -927,7 +943,6 @@ The following options need to be configured:
                CONFIG_CMD_SAVEENV        saveenv
                CONFIG_CMD_FDC          * Floppy Disk Support
                CONFIG_CMD_FAT          * FAT command support
-               CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
                CONFIG_CMD_FUSE         * Device fuse support
@@ -2854,6 +2869,26 @@ CBFS (Coreboot Filesystem) support
                The signing part is build into mkimage regardless of this
                option.
 
+- bootcount support:
+               CONFIG_BOOTCOUNT_LIMIT
+
+               This enables the bootcounter support, see:
+               http://www.denx.de/wiki/DULG/UBootBootCountLimit
+
+               CONFIG_AT91SAM9XE
+               enable special bootcounter support on at91sam9xe based boards.
+               CONFIG_BLACKFIN
+               enable special bootcounter support on blackfin based boards.
+               CONFIG_SOC_DA8XX
+               enable special bootcounter support on da850 based boards.
+               CONFIG_BOOTCOUNT_RAM
+               enable support for the bootcounter in RAM
+               CONFIG_BOOTCOUNT_I2C
+               enable support for the bootcounter on an i2c (like RTC) device.
+                       CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
+                       CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
+                                                   the bootcounter.
+                       CONFIG_BOOTCOUNT_ALEN = address len
 
 - Show boot progress:
                CONFIG_SHOW_BOOT_PROGRESS
@@ -3435,6 +3470,9 @@ typically in board_init_f() and board_init_r().
 Configuration Settings:
 -----------------------
 
+- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+               Optionally it can be defined to support 64-bit memory commands.
+
 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
                undefine this when you're short of memory.