Define this to use i/o functions instead of macros
(some hardware wont work with macros)
+ CONFIG_DRIVER_TI_EMAC
+ Support for davinci emac
+
+ CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
+ Define this if you have more then 3 PHYs.
+
CONFIG_FTGMAC100
Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
CONFIG_SH_ETHER_CACHE_WRITEBACK
If this option is set, the driver enables cache flush.
+- TPM Support:
+ CONFIG_GENERIC_LPC_TPM
+ Support for generic parallel port TPM devices. Only one device
+ per system is supported at this time.
+
+ CONFIG_TPM_TIS_BASE_ADDRESS
+ Base address where the generic TPM device is mapped
+ to. Contemporary x86 systems usually map it at
+ 0xfed40000.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
CONFIG_MXC_SPI
Enables the driver for the SPI controllers on i.MX and MXC
- SoCs. Currently only i.MX31 is supported.
+ SoCs. Currently i.MX31/35/51 are supported.
- FPGA Support: CONFIG_FPGA
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+ define this, if you want to read first the oob data
+ and then the data. This is used for example on
+ davinci plattforms.
+
- CONFIG_USE_ARCH_MEMCPY
CONFIG_USE_ARCH_MEMSET
If these options are used a optimized version of memcpy/memset will
be used if available. These functions may be faster under some
conditions but may increase the binary size.
+Freescale QE/FMAN Firmware Support:
+-----------------------------------
+
+The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
+loading of "firmware", which is encoded in the QE firmware binary format.
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_SYS_QE_FMAN_FW_ADDR
+ The address in the storage device where the firmware is located. The
+ meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+ is also specified.
+
+- CONFIG_SYS_QE_FMAN_FW_LENGTH
+ The maximum possible size of the firmware. The firmware binary format
+ has a field that specifies the actual size of the firmware, but it
+ might not be possible to read any part of the firmware unless some
+ local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NOR
+ Specifies that QE/FMAN firmware is located in NOR flash, mapped as
+ normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
+ virtual address in NOR flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NAND
+ Specifies that QE/FMAN firmware is located in NAND flash.
+ CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_MMC
+ Specifies that QE/FMAN firmware is located on the primary SD/MMC
+ device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
+ Specifies that QE/FMAN firmware is located on the primary SPI
+ device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+
Building the Software:
======================