releases in "stable" maintenance trees.
Examples:
- U-Boot v2009.11 - Release November 2009
+ U-Boot v2009.11 - Release November 2009
U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
/mips32 Files specific to MIPS32 CPUs
/xburst Files specific to Ingenic XBurst CPUs
/lib Architecture specific library files
+ /nds32 Files generic to NDS32 architecture
+ /cpu CPU specific files
+ /n1213 Files specific to Andes Technology N1213 CPUs
+ /lib Architecture specific library files
/nios2 Files generic to Altera NIOS2 architecture
/cpu CPU specific files
/lib Architecture specific library files
CONFIG_CMD_NAND * NAND support
CONFIG_CMD_NET bootp, tftpboot, rarpboot
CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
- CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
+ CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
CONFIG_CMD_PCI * pciinfo
CONFIG_CMD_PCMCIA * PCMCIA support
CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
+ CONFIG_CMD_TFTPPUT * TFTP put command (upload)
CONFIG_CMD_TIME * run command and report execution time
CONFIG_CMD_USB * USB support
CONFIG_CMD_CDP * Cisco Discover Protocol support
XXX - this list needs to get updated!
+- Device tree:
+ CONFIG_OF_CONTROL
+ If this variable is defined, U-Boot will use a device tree
+ to configure its devices, instead of relying on statically
+ compiled #defines in the board file. This option is
+ experimental and only available on a few boards. The device
+ tree is available in the global data as gd->fdt_blob.
+
+ U-Boot needs to get its device tree from somewhere. This can
+ be done using one of the two options below:
+
+ CONFIG_OF_EMBED
+ If this variable is defined, U-Boot will embed a device tree
+ binary in its image. This device tree file should be in the
+ board directory and called <soc>-<board>.dts. The binary file
+ is then picked up in board_init_f() and made available through
+ the global data structure as gd->blob.
+
+ CONFIG_OF_SEPARATE
+ If this variable is defined, U-Boot will build a device tree
+ binary. It will be called u-boot.dtb. Architecture-specific
+ code will locate it at run-time. Generally this works by:
+
+ cat u-boot.bin u-boot.dtb >image.bin
+
+ and in fact, U-Boot does this for you, creating a file called
+ u-boot-dtb.bin which is useful in the common case. You can
+ still use the individual files if you need something more
+ exotic.
+
- Watchdog:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
- CONFIG_RTC_MC13783 - use MC13783 RTC
+ CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
- NETWORK Support (PCI):
CONFIG_E1000
- Support for Intel 8254x gigabit chips.
+ Support for Intel 8254x/8257x gigabit chips.
+
+ CONFIG_E1000_SPI
+ Utility code for direct access to the SPI bus on Intel 8257x.
+ This does not do anything useful unless you set at least one
+ of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
+
+ CONFIG_E1000_SPI_GENERIC
+ Allow generic access to the SPI bus on the Intel 8257x, for
+ example with the "sspi" command.
+
+ CONFIG_CMD_E1000
+ Management command for E1000 devices. When used on devices
+ with SPI support you can reprogram the EEPROM from U-Boot.
CONFIG_E1000_FALLBACK_MAC
default MAC for empty EEPROM after production.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
+ CONFIG_DRIVER_TI_EMAC
+ Support for davinci emac
+
+ CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
+ Define this if you have more then 3 PHYs.
+
CONFIG_FTGMAC100
Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
CONFIG_SH_ETHER_CACHE_WRITEBACK
If this option is set, the driver enables cache flush.
+- TPM Support:
+ CONFIG_GENERIC_LPC_TPM
+ Support for generic parallel port TPM devices. Only one device
+ per system is supported at this time.
+
+ CONFIG_TPM_TIS_BASE_ADDRESS
+ Base address where the generic TPM device is mapped
+ to. Contemporary x86 systems usually map it at
+ 0xfed40000.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
to disable the command chpart. This is the default when you
have not defined a custom partition
+- FAT(File Allocation Table) filesystem write function support:
+ CONFIG_FAT_WRITE
+ Support for saving memory data as a file
+ in FAT formatted partition
+
- Keyboard Support:
CONFIG_ISA_KEYBOARD
Define a default value for the IP address to use for
the default Ethernet interface, in case this is not
determined through e.g. bootp.
+ (Environment variable "ipaddr")
- Server IP address:
CONFIG_SERVERIP
Defines a default value for the IP address of a TFTP
server to contact when using the "tftboot" command.
+ (Environment variable "serverip")
CONFIG_KEEP_SERVERADDR
Keeps the server's MAC address, in the env 'serveraddr'
for passing to bootargs (like Linux's netconsole option)
+- Gateway IP address:
+ CONFIG_GATEWAYIP
+
+ Defines a default value for the IP address of the
+ default router where packets to other networks are
+ sent to.
+ (Environment variable "gatewayip")
+
+- Subnet mask:
+ CONFIG_NETMASK
+
+ Defines a default value for the subnet mask (or
+ routing prefix) which is used to determine if an IP
+ address belongs to the local subnet or needs to be
+ forwarded through a router.
+ (Environment variable "netmask")
+
- Multicast TFTP Mode:
CONFIG_MCAST_TFTP
CONFIG_I2C_MULTI_BUS
This option allows the use of multiple I2C buses, each of which
- must have a controller. At any point in time, only one bus is
- active. To switch to a different bus, use the 'i2c dev' command.
+ must have a controller. At any point in time, only one bus is
+ active. To switch to a different bus, use the 'i2c dev' command.
Note that bus numbering is zero-based.
CONFIG_SYS_I2C_NOPROBES
This option specifies a list of I2C devices that will be skipped
- when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
+ when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
is set, specify a list of bus-device pairs. Otherwise, specify
a 1D array of device addresses
e.g.
#undef CONFIG_I2C_MULTI_BUS
- #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
+ #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
will skip addresses 0x50 and 0x68 on a board with one I2C bus
- #define CONFIG_I2C_MULTI_BUS
+ #define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
Enables a hardware SPI driver for general-purpose reads
and writes. As with CONFIG_SOFT_SPI, the board configuration
must define a list of chip-select function pointers.
- Currently supported on some MPC8xxx processors. For an
+ Currently supported on some MPC8xxx processors. For an
example, see include/configs/mpc8349emds.h.
CONFIG_MXC_SPI
Enables the driver for the SPI controllers on i.MX and MXC
- SoCs. Currently only i.MX31 is supported.
+ SoCs. Currently i.MX31/35/51 are supported.
- FPGA Support: CONFIG_FPGA
13 common/image.c Start multifile image verification
14 common/image.c No initial ramdisk, no multifile, continue.
- 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
+ 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
-30 arch/powerpc/lib/board.c Fatal error, hang the system
-31 post/post.c POST test failed, detected by post_output_backlog()
See also: doc/README.Modem
+Board initialization settings:
+------------------------------
+
+During Initialization u-boot calls a number of board specific functions
+to allow the preparation of board specific prerequisites, e.g. pin setup
+before drivers are initialized. To enable these callbacks the
+following configuration macros have to be defined. Currently this is
+architecture specific, so please check arch/your_architecture/lib/board.c
+typically in board_init_f() and board_init_r().
+
+- CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
+- CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
+- CONFIG_BOARD_LATE_INIT: Call board_late_init()
+- CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
Configuration Settings:
-----------------------
used) must be put below this limit, unless "bootm_low"
enviroment variable is defined and non-zero. In such case
all data for the Linux kernel must be between "bootm_low"
- and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
+ and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
variable "bootm_mapsize" will override the value of
CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
then the value in "bootm_size" will be used instead.
This setting describes a second storage area of CONFIG_ENV_SIZE
size used to hold a redundant copy of the environment data, so
that there is a valid backup copy in case there is a power failure
- during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
aligned to an erase block boundary.
- CONFIG_ENV_RANGE (optional):
- CONFIG_SYS_CCSRBAR_PHYS:
Physical address of CCSR. CCSR can be relocated to a new
physical address, if desired. In this case, this macro should
- be set to that address. Otherwise, it should be set to the
+ be set to that address. Otherwise, it should be set to the
same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
is typically relocated on 36-bit builds. It is recommended
that this macro be defined via the _HIGH and _LOW macros:
globally (CONFIG_CMD_MEM).
- CONFIG_SKIP_LOWLEVEL_INIT
- [ARM, MIPS only] If this variable is defined, then certain
+ [ARM, NDS32, MIPS only] If this variable is defined, then certain
low level initializations (like setting up the memory
controller) are omitted and/or U-Boot does not
relocate itself into RAM.
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+ define this, if you want to read first the oob data
+ and then the data. This is used for example on
+ davinci plattforms.
+
- CONFIG_USE_ARCH_MEMCPY
CONFIG_USE_ARCH_MEMSET
If these options are used a optimized version of memcpy/memset will
be used if available. These functions may be faster under some
conditions but may increase the binary size.
+Freescale QE/FMAN Firmware Support:
+-----------------------------------
+
+The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
+loading of "firmware", which is encoded in the QE firmware binary format.
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_SYS_QE_FMAN_FW_ADDR
+ The address in the storage device where the firmware is located. The
+ meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+ is also specified.
+
+- CONFIG_SYS_QE_FMAN_FW_LENGTH
+ The maximum possible size of the firmware. The firmware binary format
+ has a field that specifies the actual size of the firmware, but it
+ might not be possible to read any part of the firmware unless some
+ local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NOR
+ Specifies that QE/FMAN firmware is located in NOR flash, mapped as
+ normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
+ virtual address in NOR flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_NAND
+ Specifies that QE/FMAN firmware is located in NAND flash.
+ CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_MMC
+ Specifies that QE/FMAN firmware is located on the primary SD/MMC
+ device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+- CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
+ Specifies that QE/FMAN firmware is located on the primary SPI
+ device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+
+
Building the Software:
======================
tftpboot- boot image via network using TFTP protocol
and env variables "ipaddr" and "serverip"
(and eventually "gatewayip")
+tftpput - upload a file via network using TFTP protocol
rarpboot- boot image via network using RARP/TFTP protocol
diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
loads - load S-Record file over serial line
kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
bootm_mapsize.
- bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
+ bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
This variable is given as a hexadecimal number and it
defines the size of the memory region starting at base
address bootm_low that is accessible by the Linux kernel
add the information it needs into it, and the memory
must be accessible by the kernel.
+ fdtcontroladdr- if set this is the address of the control flattened
+ device tree used by U-Boot when CONFIG_OF_CONTROL is
+ defined.
+
i2cfast - (PPC405GP|PPC405EP only)
if set to 'y' configures Linux I2C driver for fast
mode (400kHZ). This environment variable is used in
boards currenlty use other variables for these purposes, and some
boards use these variables for other purposes.
-Image File Name RAM Address Flash Location
------ --------- ----------- --------------
-u-boot u-boot u-boot_addr_r u-boot_addr
-Linux kernel bootfile kernel_addr_r kernel_addr
-device tree blob fdtfile fdt_addr_r fdt_addr
-ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
+Image File Name RAM Address Flash Location
+----- --------- ----------- --------------
+u-boot u-boot u-boot_addr_r u-boot_addr
+Linux kernel bootfile kernel_addr_r kernel_addr
+device tree blob fdtfile fdt_addr_r fdt_addr
+ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
The following environment variables may be used and automatically
updated by the network boot commands ("bootp" and "rarpboot"),
is raised.
If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
-will be programmed into hardware as part of the initialization process. This
+will be programmed into hardware as part of the initialization process. This
may be skipped by setting the appropriate 'ethmacskip' environment variable.
The naming convention is as follows:
"ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
INTEGRITY).
* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
- IA64, MIPS, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
- Currently supported: ARM, AVR32, Intel x86, MIPS, Nios II, PowerPC).
+ IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
+ Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
* Compression Type (uncompressed, gzip, bzip2)
* Load Address
* Entry Point
Note: on Nios II, we give "-G0" option to gcc and don't use gp
to access small data sections, so gp is free.
+On NDS32, the following registers are used:
+
+ R0-R1: argument/return
+ R2-R5: argument
+ R15: temporary register for assembler
+ R16: trampoline register
+ R28: frame pointer (FP)
+ R29: global pointer (GP)
+ R30: link register (LP)
+ R31: stack pointer (SP)
+ PC: program counter (PC)
+
+ ==> U-Boot will use R10 to hold a pointer to the global data
+
NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
or current versions of GCC may "optimize" the code too much.
projects / karo-tx-uboot.git / blobdiff