9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
with a fix speed from 100000 and the slave addr 0!
+ - drivers/i2c/ihs_i2c.c
+ - activate this driver with CONFIG_SYS_I2C_IHS
+ - CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0
+ - CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0
+ - CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0
+ - CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1
+ - CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1
+ - CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1
+ - CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2
+ - CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2
+ - CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2
+ - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
+ - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
+ - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
+
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
disabled. If a board need legacy image format support
enable this through CONFIG_IMAGE_FORMAT_LEGACY
+ CONFIG_FIT_DISABLE_SHA256
+ Supporting SHA256 hashes has quite an impact on binary size.
+ For constrained systems sha256 hash support can be disabled
+ with this option.
+
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
environment area within the total memory of your DataFlash placed
at the specified address.
+- CONFIG_ENV_IS_IN_SPI_FLASH:
+
+ Define this if you have a SPI Flash memory device which you
+ want to use for the environment.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SECT_SIZE:
+
+ Define the SPI flash's sector size.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ This setting describes a second storage area of CONFIG_ENV_SIZE
+ size used to hold a redundant copy of the environment data, so
+ that there is a valid backup copy in case there is a power failure
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SPI_BUS (optional):
+ - CONFIG_ENV_SPI_CS (optional):
+
+ Define the SPI bus and chip select. If not defined they will be 0.
+
+ - CONFIG_ENV_SPI_MAX_HZ (optional):
+
+ Define the SPI max work clock. If not defined then use 1MHz.
+
+ - CONFIG_ENV_SPI_MODE (optional):
+
+ Define the SPI work mode. If not defined then use SPI_MODE_3.
+
- CONFIG_ENV_IS_IN_REMOTE:
Define this if you have a remote memory space which you
You will probably want to define these to avoid a really noisy system
when storing the env in UBI.
+- CONFIG_ENV_IS_IN_FAT:
+ Define this if you want to use the FAT file system for the environment.
+
+ - FAT_ENV_INTERFACE:
+
+ Define this to a string that is the name of the block device.
+
+ - FAT_ENV_DEV_AND_PART:
+
+ Define this to a string to specify the partition of the device. It can
+ be as following:
+
+ "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
+ - "D:P": device D partition P. Error occurs if device D has no
+ partition table.
+ - "D:0": device D.
+ - "D" or "D:": device D partition 1 if device D has partition
+ table, or the whole device D if has no partition
+ table.
+ - "D:auto": first partition in device D with bootable flag set.
+ If none, first valid paratition in device D. If no
+ partition table then means device D.
+
+ - FAT_ENV_FILE:
+
+ It's a string of the FAT file name. This file use to store the
+ envrionment.
+
+ - CONFIG_FAT_WRITE:
+ This should be defined. Otherwise it cannot save the envrionment file.
+
- CONFIG_ENV_IS_IN_MMC:
Define this if you have an MMC device which you want to use for the
window->master inbound window->master LAW->the ucode address in
master's memory space.
+Freescale Layerscape Management Complex Firmware Support:
+---------------------------------------------------------
+The Freescale Layerscape Management Complex (MC) supports the loading of
+"firmware".
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_FSL_MC_ENET
+ Enable the MC driver for Layerscape SoCs.
+
+- CONFIG_SYS_LS_MC_FW_ADDR
+ The address in the storage device where the firmware is located. The
+ meaning of this address depends on which CONFIG_SYS_LS_MC_FW_IN_xxx macro
+ is also specified.
+
+- CONFIG_SYS_LS_MC_FW_LENGTH
+ The maximum possible size of the firmware. The firmware binary format
+ has a field that specifies the actual size of the firmware, but it
+ might not be possible to read any part of the firmware unless some
+ local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_LS_MC_FW_IN_NOR
+ Specifies that MC firmware is located in NOR flash, mapped as
+ normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
+ virtual address in NOR flash.
+
Building the Software:
======================
projects / karo-tx-uboot.git / blobdiff