Prepare v2013.10-rc2

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 391880765a0865f05a71efc6dedf40d99e61d7fe..677c3dc252174f62dacc13bb93ab4aad702e63a6 100644 (file)
--- a/README
+++ b/README
@@ -2641,6 +2641,21 @@ CBFS (Coreboot Filesystem) support
                Note: There is also a sha1sum command, which should perhaps
                be deprecated in favour of 'hash sha1'.
 
+- Freescale i.MX specific commands:
+               CONFIG_CMD_HDMIDETECT
+               This enables 'hdmidet' command which returns true if an
+               HDMI monitor is detected.  This command is i.MX 6 specific.
+
+               CONFIG_CMD_BMODE
+               This enables the 'bmode' (bootmode) command for forcing
+               a boot from specific media.
+
+               This is useful for forcing the ROM's usb downloader to
+               activate upon a watchdog reset which is nice when iterating
+               on U-Boot.  Using the reset button or running bmode normal
+               will set it back to normal.  This command currently
+               supports i.MX53 and i.MX6.
+
 - Signing support:
                CONFIG_RSA
 
@@ -3075,6 +3090,14 @@ FIT uImage format:
                Support for NAND boot using simple NAND drivers that
                expose the cmd_ctrl() interface.
 
+               CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+               Set for the SPL on PPC mpc8xxx targets, support for
+               arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+
+               CONFIG_SPL_COMMON_INIT_DDR
+               Set for common ddr init with serial presence detect in
+               SPL binary.
+
                CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
                CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
                CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
@@ -3144,6 +3167,17 @@ FIT uImage format:
                option to re-enable it. This will affect the output of the
                bootm command when booting a FIT image.
 
+- TPL framework
+               CONFIG_TPL
+               Enable building of TPL globally.
+
+               CONFIG_TPL_PAD_TO
+               Image offset to which the TPL should be padded before appending
+               the TPL payload. By default, this is defined as
+                CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
+                CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
+                payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
+
 Modem Support:
 --------------
 
@@ -4181,6 +4215,11 @@ Low Level (hardware related) configuration options:
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 
+- CONFIG_TPL_BUILD
+               Modifies the behaviour of start.S  when compiling a loader
+               that is executed after the SPL and before the actual U-Boot.
+               It is loaded by the SPL.
+
 - CONFIG_SYS_MPC85XX_NO_RESETVEC
                Only for 85xx systems. If this variable is specified, the section
                .resetvec is not kept and the section .bootpg is placed in the
@@ -4627,6 +4666,12 @@ List of environment variables (most likely not complete):
 
   npe_ucode    - set load address for the NPE microcode
 
+  silent_linux  - If set then linux will be told to boot silently, by
+                 changing the console to be empty. If "yes" it will be
+                 made silent. If "no" it will not be made silent. If
+                 unset, then it will be made silent if the U-Boot console
+                 is silent.
+
   tftpsrcport  - If this is set, the value is used for TFTP's
                  UDP source port.