Blackfin: call watchdog_init() for external watchdogs

[karo-tx-uboot.git] / README

diff --git a/README b/README
index fe6ca98d82b3fd9209edf67442cbd117d7218639..940b50794213d72606271bce2204d15c8f72c616 100644 (file)
--- a/README
+++ b/README
@@ -777,7 +777,7 @@ The following options need to be configured:
                CONFIG_LBA48
 
                Set this to enable support for disks larger than 137GB
-               Also look at CONFIG_SYS_64BIT_LBA ,CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
+               Also look at CONFIG_SYS_64BIT_LBA.
                Whithout these , LBA48 support uses 32bit variables and will 'only'
                support disks up to 2.1TB.
 
@@ -822,6 +822,16 @@ The following options need to be configured:
 
 - NETWORK Support (other):
 
+               CONFIG_DRIVER_AT91EMAC
+               Support for AT91RM9200 EMAC.
+
+                       CONFIG_RMII
+                       Define this to use reduced MII inteface
+
+                       CONFIG_DRIVER_AT91EMAC_QUIET
+                       If this defined, the driver is quiet.
+                       The driver doen't show link status messages.
+
                CONFIG_DRIVER_LAN91C96
                Support for SMSC's LAN91C96 chips.
 
@@ -2447,6 +2457,19 @@ to save the current settings.
        - CONFIG_SYS_EEPROM_SIZE:
          The size in bytes of the EEPROM device.
 
+       - CONFIG_ENV_EEPROM_IS_ON_I2C
+         define this, if you have I2C and SPI activated, and your
+         EEPROM, which holds the environment, is on the I2C bus.
+
+       - CONFIG_I2C_ENV_EEPROM_BUS
+         if you have an Environment on an EEPROM reached over
+         I2C muxes, you can define here, how to reach this
+         EEPROM. For example:
+
+         #define CONFIG_I2C_ENV_EEPROM_BUS       "pca9547:70:d\0"
+
+         EEPROM which holds the environment, is reached over
+         a pca9547 i2c mux with address 0x70, channel 3.
 
 - CONFIG_ENV_IS_IN_DATAFLASH:
 
@@ -2524,13 +2547,6 @@ use the "saveenv" command to store a valid environment.
 - CONFIG_SYS_FAULT_MII_ADDR:
                MII address of the PHY to check for the Ethernet link state.
 
-- CONFIG_SYS_64BIT_VSPRINTF:
-               Makes vsprintf (and all *printf functions) support printing
-               of 64bit values by using the L quantifier
-
-- CONFIG_SYS_64BIT_STRTOUL:
-               Adds simple_strtoull that returns a 64bit value
-
 - CONFIG_NS16550_MIN_FUNCTIONS:
                Define this if you desire to only have use of the NS16550_init
                and NS16550_putc functions for the serial driver located at
@@ -2989,7 +3005,9 @@ environment. As long as you don't save the environment you are
 working with an in-memory copy. In case the Flash area containing the
 environment is erased by accident, a default environment is provided.
 
-Some configuration options can be set using Environment Variables:
+Some configuration options can be set using Environment Variables.
+
+List of environment variables (most likely not complete):
 
   baudrate     - see CONFIG_BAUDRATE
 
@@ -3101,7 +3119,7 @@ Some configuration options can be set using Environment Variables:
                  available network interfaces.
                  It just stays at the currently selected interface.
 
-   netretry    - When set to "no" each network operation will
+  netretry     - When set to "no" each network operation will
                  either succeed or fail without retrying.
                  When set to "once" the network operation will
                  fail when all the available network interfaces
@@ -3117,7 +3135,18 @@ Some configuration options can be set using Environment Variables:
   tftpdstport  - If this is set, the value is used for TFTP's UDP
                  destination port instead of the Well Know Port 69.
 
-   vlan                - When set to a value < 4095 the traffic over
+  tftpblocksize - Block size to use for TFTP transfers; if not set,
+                 we use the TFTP server's default block size
+
+  tftptimeout  - Retransmission timeout for TFTP packets (in milli-
+                 seconds, minimum value is 1000 = 1 second). Defines
+                 when a packet is considered to be lost so it has to
+                 be retransmitted. The default is 5000 = 5 seconds.
+                 Lowering this value may make downloads succeed
+                 faster in networks with high packet loss rates or
+                 with unreliable TFTP servers.
+
+  vlan         - When set to a value < 4095 the traffic over
                  Ethernet is encapsulated/received over 802.1q
                  VLAN tagged frames.
 
@@ -3916,7 +3945,9 @@ For PowerPC, the following registers have specific use:
        R30:    GOT pointer
        R31:    frame pointer
 
-       (U-Boot also uses R14 as internal GOT pointer.)
+       (U-Boot also uses R12 as internal GOT pointer. r12
+       is a volatile register so r12 needs to be reset when
+       going back and forth between asm and C)
 
     ==> U-Boot will use R2 to hold a pointer to the global data