Defines the string to utilize when trying to match PCIe device
tree nodes for the given platform.
+ CONFIG_SYS_PPC_E500_DEBUG_TLB
+
+ Enables a temporary TLB entry to be used during boot to work
+ around limitations in e500v1 and e500v2 external debugger
+ support. This reduces the portions of the boot code where
+ breakpoints and single stepping do not work. The value of this
+ symbol should be set to the TLB1 entry to be used for this
+ purpose.
+
+ CONFIG_SYS_FSL_ERRATUM_A004510
+
+ Enables a workaround for erratum A004510. If set,
+ then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
+ CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
+
+ CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
+ CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
+
+ Defines one or two SoC revisions (low 8 bits of SVR)
+ for which the A004510 workaround should be applied.
+
+ The rest of SVR is either not relevant to the decision
+ of whether the erratum is present (e.g. p2040 versus
+ p2041) or is implied by the build target, which controls
+ whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
+
+ See Freescale App Note 4493 for more information about
+ this erratum.
+
+ CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
+
+ This is the value to write into CCSR offset 0x18600
+ according to the A004510 workaround.
+
+- Generic CPU options:
+ CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
+
+ Defines the endianess of the CPU. Implementation of those
+ values is arch specific.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
Select high exception vectors of the ARM core, e.g., do not
clear the V bit of the c1 register of CP15.
+ CONFIG_SYS_THUMB_BUILD
+
+ Use this flag to build U-Boot using the Thumb instruction
+ set for ARM architectures. Thumb instruction set provides
+ better code density. For ARM architectures that support
+ Thumb2 this flag will result in Thumb2 code generated by
+ GCC.
+
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
- Monitor Functions:
Monitor commands can be included or excluded
from the build by using the #include files
- "config_cmd_all.h" and #undef'ing unwanted
- commands, or using "config_cmd_default.h"
+ <config_cmd_all.h> and #undef'ing unwanted
+ commands, or using <config_cmd_default.h>
and augmenting with additional #define's
for wanted commands.
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
+ CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
+ (169.254.*.*)
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
CONFIG_CMD_TIME * run command and report execution time
CONFIG_CMD_USB * USB support
CONFIG_CMD_CDP * Cisco Discover Protocol support
- CONFIG_CMD_FSL * Microblaze FSL support
+ CONFIG_CMD_MFSL * Microblaze FSL support
EXAMPLE: If you want all functions except of network
If this variable is defined, an environment variable
named "ver" is created by U-Boot showing the U-Boot
version as printed by the "version" command.
- This variable is readonly.
+ Any change to this variable will be reverted at the
+ next reset.
- Real-Time Clock:
commands like bootm or iminfo. This option is
automatically enabled when you select CONFIG_CMD_DATE .
-- Partition Support:
- CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
- and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
+- Partition Labels (disklabels) Supported:
+ Zero or more of the following:
+ CONFIG_MAC_PARTITION Apple's MacOS partition table.
+ CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
+ Intel architecture, USB sticks, etc.
+ CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
+ CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
+ bootloader. Note 2TB partition limit; see
+ disk/part_efi.c
+ CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
CONFIG_CMD_SCSI) you must configure support for at
- least one partition type as well.
+ least one non-MTD partition type as well.
- IDE Reset method:
CONFIG_IDE_RESET_ROUTINE - this is defined in several
Define this to have a tty type of device available to
talk to the UDC device
+ CONFIG_USBD_HS
+ Define this to enable the high speed support for usb
+ device and usbtty. If this feature is enabled, a routine
+ int is_usbd_high_speed(void)
+ also needs to be defined by the driver to dynamically poll
+ whether the enumeration has succeded at high speed or full
+ speed.
+
CONFIG_SYS_CONSOLE_IS_IN_ENV
Define this if you want stdin, stdout &/or stderr to
be set to usbtty.
can be displayed via the splashscreen support or the
bmp command.
+- Do compresssing for memory range:
+ CONFIG_CMD_ZIP
+
+ If this option is set, it would use zlib deflate method
+ to compress the specified memory at its best effort.
+
- Compression support:
CONFIG_BZIP2
CONFIG_BOOTP_NTPSERVER
CONFIG_BOOTP_TIMEOFFSET
CONFIG_BOOTP_VENDOREX
+ CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
environment variable, not the BOOTP server.
+ CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
+ after the configured retry count, the call will fail
+ instead of starting over. This can be used to fail over
+ to Link-local IP address configuration if the DHCP server
+ is not available.
+
CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
serverip from a DHCP server, it is possible that more
than one DNS serverip is offered to the client.
the DHCP timeout and retry process takes a longer than
this delay.
+ - Link-local IP address negotiation:
+ Negotiate with other link-local clients on the local network
+ for an address that doesn't require explicit configuration.
+ This is especially useful if a DHCP server cannot be guaranteed
+ to exist in all environments that the device must operate.
+
+ See doc/README.link-local for more information.
+
- CDP Options:
CONFIG_CDP_DEVICE_ID
Timeout waiting for an ARP reply in milliseconds.
+ CONFIG_NFS_TIMEOUT
+
+ Timeout in milliseconds used in NFS protocol.
+ If you encounter "ERROR: Cannot umount" in nfs command,
+ try longer timeout such as
+ #define CONFIG_NFS_TIMEOUT 10000UL
+
- Command Interpreter:
CONFIG_AUTO_COMPLETE
the environment like the "source" command or the
boot command first.
+ CONFIG_ENV_VARS_UBOOT_CONFIG
+
+ Define this in order to add variables describing the
+ U-Boot build configuration to the default environment.
+ These will be named arch, cpu, board, vendor, and soc.
+
+ Enabling this option will cause the following to be defined:
+
+ - CONFIG_SYS_ARCH
+ - CONFIG_SYS_CPU
+ - CONFIG_SYS_BOARD
+ - CONFIG_SYS_VENDOR
+ - CONFIG_SYS_SOC
+
- DataFlash Support:
CONFIG_HAS_DATAFLASH
CONFIG_SYS_SPL_MALLOC_SIZE
The size of the malloc pool used in SPL.
+ CONFIG_SPL_FRAMEWORK
+ Enable the SPL framework under common/. This framework
+ supports MMC, NAND and YMODEM loading of U-Boot and NAND
+ NAND loading of the Linux Kernel.
+
+ CONFIG_SPL_DISPLAY_PRINT
+ For ARM, enable an optional function to print more information
+ about the running system.
+
CONFIG_SPL_LIBCOMMON_SUPPORT
Support for common/libcommon.o in SPL binary
CONFIG_SPL_SPI_SUPPORT
Support for drivers/spi/libspi.o in SPL binary
+ CONFIG_SPL_RAM_DEVICE
+ Support for running image already present in ram, in SPL binary
+
CONFIG_SPL_LIBGENERIC_SUPPORT
Support for lib/libgeneric.o in SPL binary
environment area within the total memory of your DataFlash placed
at the specified address.
+- CONFIG_ENV_IS_IN_REMOTE:
+
+ Define this if you have a remote memory space which you
+ want to use for the local device's environment.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the address and size of the
+ environment area within the remote memory space. The
+ local device can get the environment from remote memory
+ space by SRIO or PCIE links.
+
+BE CAREFUL! For some special cases, the local device can not use
+"saveenv" command. For example, the local device will get the
+environment stored in a remote NOR flash by SRIO or PCIE link,
+but it can not erase, write this NOR flash by SRIO or PCIE interface.
+
- CONFIG_ENV_IS_IN_NAND:
Define this if you have a NAND device which you want to use
Disable PCI-Express on systems where it is supported but not
required.
+- CONFIG_PCI_ENUM_ONLY
+ Only scan through and get the devices on the busses.
+ Don't do any setup work, presumably because someone or
+ something has already done it, and we don't need to do it
+ a second time. Useful for platforms that are pre-booted
+ by coreboot or similar.
+
- CONFIG_SYS_SRIO:
Chip has SRIO or not
Specifies that QE/FMAN firmware is located on the primary SPI
device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
+- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+ Specifies that QE/FMAN firmware is located in the remote (master)
+ memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
+ can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
+ window->master inbound window->master LAW->the ucode address in
+ master's memory space.
Building the Software:
======================
make NAME_config
where "NAME_config" is the name of one of the existing configu-
-rations; see the main Makefile for supported names.
+rations; see boards.cfg for supported names.
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for
steps:
1. Add a new configuration option for your board to the toplevel
- "Makefile" and to the "MAKEALL" script, using the existing
- entries as examples. Note that here and at many other places
- boards and other names are listed in alphabetical sort order. Please
- keep this order.
+ "boards.cfg" file, using the existing entries as examples.
+ Follow the instructions there to keep the boards in order.
2. Create a new directory to hold your board specific code. Add any
files you need. In your board directory, you will need at least
the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
projects / karo-tx-uboot.git / blobdiff