ipu common: reset ipuv3 correctly

[karo-tx-uboot.git] / README

diff --git a/README b/README
index a664607b524e155644d91e35755027b8f9d3601b..afdf591c623f6cfa5c507d6918e738dea12b2c79 100644 (file)
--- a/README
+++ b/README
@@ -363,6 +363,12 @@ The following options need to be configured:
                ICache only when Code runs from RAM.
 
 - 85xx CPU Options:
+               CONFIG_SYS_PPC64
+
+               Specifies that the core is a 64-bit PowerPC implementation (implements
+               the "64" category of the Power ISA). This is necessary for ePAPR
+               compliance, among other possible reasons.
+
                CONFIG_SYS_FSL_TBCLK_DIV
 
                Defines the core time base clock divider ratio compared to the
@@ -655,6 +661,10 @@ The following options need to be configured:
                                                additional board info beside
                                                the logo
 
+               When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
+               a limited number of ANSI escape sequences (cursor control,
+               erase functions and limited graphics rendition control).
+
                When CONFIG_CFB_CONSOLE is defined, video console is
                default i/o. Serial console can be forced with
                environment 'console=serial'.
@@ -801,9 +811,11 @@ The following options need to be configured:
                CONFIG_CMD_EEPROM       * EEPROM read/write support
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_EXPORTENV    * export the environment
+               CONFIG_CMD_EXT2         * ext2 command support
+               CONFIG_CMD_EXT4         * ext4 command support
                CONFIG_CMD_SAVEENV        saveenv
                CONFIG_CMD_FDC          * Floppy Disk Support
-               CONFIG_CMD_FAT          * FAT partition support
+               CONFIG_CMD_FAT          * FAT command support
                CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
@@ -1033,6 +1045,9 @@ The following options need to be configured:
                devices.
                CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
 
+                The environment variable 'scsidevs' is set to the number of
+                SCSI devices found during the last scan.
+
 - NETWORK Support (PCI):
                CONFIG_E1000
                Support for Intel 8254x/8257x gigabit chips.
@@ -2176,8 +2191,8 @@ CBFS (Coreboot Filesystem) support
                following board configurations are known to be
                "pRAM-clean":
 
-                       ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
-                       HERMES, IP860, RPXlite, LWMON, LANTEC,
+                       IVMS8, IVML24, SPD8xx, TQM8xxL,
+                       HERMES, IP860, RPXlite, LWMON,
                        FLAGADM, TQM8260
 
 - Error Recovery:
@@ -2303,6 +2318,12 @@ CBFS (Coreboot Filesystem) support
                - CONFIG_SYS_VENDOR
                - CONFIG_SYS_SOC
 
+               CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+               Define this in order to add variables describing certain
+               run-time determined information about the hardware to the
+               environment.  These will be named board_name, board_rev.
+
 - DataFlash Support:
                CONFIG_HAS_DATAFLASH