/x86 Files generic to x86 architecture
/api Machine/arch independent API for external apps
/board Board dependent files
+/cmd U-Boot commands functions
/common Misc architecture independent functions
/configs Board default configuration files
/disk Code for disk drive partition handling
with a special header) as build targets. By defining
CONFIG_BUILD_TARGET in the SoC / board header, this
special image will be automatically built upon calling
- make / MAKEALL.
+ make / buildman.
CONFIG_IDENT_STRING
CONFIG_SPL_INIT_MINIMAL
Arch init code should be built for a very small image
- CONFIG_SPL_LIBCOMMON_SUPPORT
- Support for common/libcommon.o in SPL binary
-
- CONFIG_SPL_LIBDISK_SUPPORT
- Support for disk/libdisk.o in SPL binary
-
- CONFIG_SPL_I2C_SUPPORT
- Support for drivers/i2c/libi2c.o in SPL binary
-
- CONFIG_SPL_GPIO_SUPPORT
- Support for drivers/gpio/libgpio.o in SPL binary
-
- CONFIG_SPL_MMC_SUPPORT
- Support for drivers/mmc/libmmc.o in SPL binary
-
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
Address and partition on the MMC to load U-Boot from
Partition on the MMC to load U-Boot from when the MMC is being
used in fs mode
- CONFIG_SPL_FAT_SUPPORT
- Support for fs/fat/libfat.o in SPL binary
-
- CONFIG_SPL_EXT_SUPPORT
- Support for EXT filesystem in SPL binary
-
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Filename to read to load U-Boot when reading from filesystem
Support for a lightweight UBI (fastmap) scanner and
loader
- CONFIG_SPL_MTD_SUPPORT
- Support for the MTD subsystem within SPL. Useful for
- environment on NAND support within SPL.
-
CONFIG_SPL_NAND_RAW_ONLY
Support to boot only raw u-boot.bin images. Use this only
if you need to save space.
- CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
- Set for the SPL on PPC mpc8xxx targets, support for
- drivers/ddr/fsl/libddr.o in SPL binary.
-
CONFIG_SPL_COMMON_INIT_DDR
Set for common ddr init with serial presence detect in
SPL binary.
Support for an OMAP3-specific set of functions to return the
ID and MFR of the first attached NAND chip, if present.
- CONFIG_SPL_SERIAL_SUPPORT
- Support for drivers/serial/libserial.o in SPL binary
-
- CONFIG_SPL_SPI_FLASH_SUPPORT
- Support for drivers/mtd/spi/libspi_flash.o in SPL binary
-
- CONFIG_SPL_SPI_SUPPORT
- Support for drivers/spi/libspi.o in SPL binary
-
CONFIG_SPL_RAM_DEVICE
Support for running image already present in ram, in SPL binary
- CONFIG_SPL_LIBGENERIC_SUPPORT
- Support for lib/libgeneric.o in SPL binary
-
- CONFIG_SPL_ENV_SUPPORT
- Support for the environment operating in SPL binary
-
- CONFIG_SPL_NET_SUPPORT
- Support for the net/libnet.o in SPL binary.
- It conflicts with SPL env from storage medium specified by
- CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
-
CONFIG_SPL_PAD_TO
Image offset to which the SPL should be padded before appending
the SPL payload. By default, this is defined as
"Debug Server firmware" and triggering SP boot-rom.
This firmware often needs to be loaded during U-Boot booting.
-- CONFIG_FSL_DEBUG_SERVER
- Enable the Debug Server for Layerscape SoCs.
-
-- CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE
- Define minimum DDR size required for debug server image
-
- CONFIG_SYS_MC_RSV_MEM_ALIGN
Define alignment of reserved memory MC requires
But before you submit such a patch, please verify that your modifi-
cation did not break existing code. At least make sure that *ALL* of
the supported boards compile WITHOUT ANY compiler warnings. To do so,
-just run the "MAKEALL" script, which will configure and build U-Boot
-for ALL supported system. Be warned, this will take a while. You can
-select which (cross) compiler to use by passing a `CROSS_COMPILE'
-environment variable to the script, i. e. to use the ELDK cross tools
-you can type
-
- CROSS_COMPILE=ppc_8xx- MAKEALL
-
-or to build on a native PowerPC system you can type
-
- CROSS_COMPILE=' ' MAKEALL
-
-When using the MAKEALL script, the default behaviour is to build
-U-Boot in the source directory. This location can be changed by
-setting the BUILD_DIR environment variable. Also, for each target
-built, the MAKEALL script saves two log files (<target>.ERR and
-<target>.MAKEALL) in the <source dir>/LOG directory. This default
-location can be changed by setting the MAKEALL_LOGDIR environment
-variable. For example:
-
- export BUILD_DIR=/tmp/build
- export MAKEALL_LOGDIR=/tmp/log
- CROSS_COMPILE=ppc_8xx- MAKEALL
-
-With the above settings build objects are saved in the /tmp/build,
-log files are saved in the /tmp/log and the source tree remains clean
-during the whole build process.
+just run the buildman script (tools/buildman/buildman), which will
+configure and build U-Boot for ALL supported system. Be warned, this
+will take a while. Please see the buildman README, or run 'buildman -H'
+for documentation.
See also "U-Boot Porting Guide" below.
Notes:
-* Before sending the patch, run the MAKEALL script on your patched
+* Before sending the patch, run the buildman script on your patched
source tree and make sure that no errors or warnings are reported
for any of the boards.
projects / karo-tx-uboot.git / blobdiff