CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
- CONFIG_CMD_FUSE Device fuse support
+ CONFIG_CMD_FUSE * Device fuse support
CONFIG_CMD_GETTIME * Get time since boot
CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_GREPENV * search environment
CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all images found in NOR flash
- CONFIG_CMD_IMLS_NAND List all images found in NAND flash
+ CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
CONFIG_CMD_IMMAP * IMMR dump support
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_INI * import data from an ini file into the env
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
- CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
+ CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
(169.254.*.*)
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
- CONFIG_CMD_MD5SUM print md5 message digest
+ CONFIG_CMD_MD5SUM * print md5 message digest
(requires CONFIG_CMD_MEMORY and CONFIG_MD5)
CONFIG_CMD_MEMINFO * Display detailed memory information
CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, loopw
- CONFIG_CMD_MEMTEST mtest
+ CONFIG_CMD_MEMTEST * mtest
CONFIG_CMD_MISC Misc functions like sleep etc
CONFIG_CMD_MMC * MMC memory mapped support
CONFIG_CMD_MII * MII utility commands
CONFIG_CMD_MTDPARTS * MTD partition support
CONFIG_CMD_NAND * NAND support
CONFIG_CMD_NET bootp, tftpboot, rarpboot
+ CONFIG_CMD_NFS NFS support
CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
CONFIG_CMD_PCI * pciinfo
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
CONFIG_CMD_SF * Read/write/erase SPI NOR flash
- CONFIG_CMD_SHA1SUM print sha1 memory digest
+ CONFIG_CMD_SHA1SUM * print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_USB * USB support
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_MFSL * Microblaze FSL support
+ CONFIG_CMD_XIMG Load part of Multi Image
EXAMPLE: If you want all functions except of network
CONFIG_TPM_TIS_I2C_BURST_LIMITATION
Define the burst count bytes upper limit
+ CONFIG_TPM_ATMEL_TWI
+ Support for Atmel TWI TPM device. Requires I2C support.
+
CONFIG_TPM_TIS_LPC
Support for generic parallel port TPM devices. Only one device
per system is supported at this time.
to. Contemporary x86 systems usually map it at
0xfed40000.
+ CONFIG_CMD_TPM
+ Add tpm monitor functions.
+ Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
+ provides monitor access to authorized functions.
+
+ CONFIG_TPM
+ Define this to enable the TPM support library which provides
+ functional interfaces to some TPM commands.
+ Requires support for a TPM device.
+
+ CONFIG_TPM_AUTH_SESSIONS
+ Define this to enable authorized functions in the TPM library.
+ Requires CONFIG_TPM and CONFIG_SHA1.
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405, MPC5200); define
CONFIG_DFU_NAND
This enables support for exposing NAND devices via DFU.
+ CONFIG_SYS_DFU_DATA_BUF_SIZE
+ Dfu transfer uses a buffer before writing data to the
+ raw storage device. Make the size (in bytes) of this buffer
+ configurable. The size of this buffer is also configurable
+ through the "dfu_bufsiz" environment variable.
+
CONFIG_SYS_DFU_MAX_FILE_SIZE
When updating files rather than the raw storage device,
we use a static buffer to copy the file into and then write
=> vertically centered image
at x = dspWidth - bmpWidth - 9
- CONFIG_SPLASH_SCREEN_PREPARE
-
- If this option is set then the board_splash_screen_prepare()
- function, which must be defined in your code, is called as part
- of the splash screen display sequence. It gives the board an
- opportunity to prepare the splash image data before it is
- processed and sent to the frame buffer by U-Boot.
-
- Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
If this option is set, additionally to standard BMP
Note: There is also a sha1sum command, which should perhaps
be deprecated in favour of 'hash sha1'.
+- Signing support:
+ CONFIG_RSA
+
+ This enables the RSA algorithm used for FIT image verification
+ in U-Boot. See doc/uImage/signature for more information.
+
+ The signing part is build into mkimage regardless of this
+ option.
+
+
- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
most specific compatibility entry of U-Boot's fdt's root node.
The order of entries in the configuration's fdt is ignored.
+ CONFIG_FIT_SIGNATURE
+ This option enables signature verification of FIT uImages,
+ using a hash signed and verified using RSA. See
+ doc/uImage.FIT/signature.txt for more details.
+
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
projects / karo-tx-uboot.git / blobdiff