/cpu CPU specific files
/arm720t Files specific to ARM 720 CPUs
/arm920t Files specific to ARM 920 CPUs
- /at91rm9200 Files specific to Atmel AT91RM9200 CPU
- /imx Files specific to Freescale MC9328 i.MX CPUs
- /s3c24x0 Files specific to Samsung S3C24X0 CPUs
+ /at91rm9200 Files specific to Atmel AT91RM9200 CPU
+ /imx Files specific to Freescale MC9328 i.MX CPUs
+ /s3c24x0 Files specific to Samsung S3C24X0 CPUs
/arm925t Files specific to ARM 925 CPUs
/arm926ejs Files specific to ARM 926 CPUs
/arm1136 Files specific to ARM 1136 CPUs
/mips Files generic to MIPS architecture
/cpu CPU specific files
/lib Architecture specific library files
- /nios Files generic to Altera NIOS architecture
- /cpu CPU specific files
- /lib Architecture specific library files
/nios2 Files generic to Altera NIOS2 architecture
/cpu CPU specific files
/lib Architecture specific library files
- /ppc Files generic to PowerPC architecture
+ /powerpc Files generic to PowerPC architecture
/cpu CPU specific files
/74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
/mpc5xx Files specific to Freescale MPC5xx CPUs
the CPU's i2c node address).
Now, the u-boot i2c code for the mpc8xx
- (arch/ppc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
+ (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
and so its address should therefore be cleared to 0 (See,
eg, MPC823e User's Manual p.16-473). So, set
CONFIG_SYS_I2C_SLAVE to 0.
#define I2C_DELAY udelay(2)
+ CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
+
+ If your arch supports the generic GPIO framework (asm/gpio.h),
+ then you may alternatively define the two GPIOs that are to be
+ used as SCL / SDA. Any of the previous I2C_xxx macros will
+ have GPIO-based defaults assigned to them as appropriate.
+
+ You should define these to the GPIO value as given directly to
+ the generic GPIO functions.
+
CONFIG_SYS_I2C_INIT_BOARD
When a board is reset during an i2c bus transfer
custom i2c_init_board() routine in boards/xxx/board.c
is run early in the boot sequence.
+ CONFIG_SYS_I2C_BOARD_LATE_INIT
+
+ An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
+ defined a custom i2c_board_late_init() routine in
+ boards/xxx/board.c is run AFTER the operations in i2c_init()
+ is completed. This callpoint can be used to unreset i2c bus
+ using CPU i2c controller register accesses for CPUs whose i2c
+ controller provide such a method. It is called at the end of
+ i2c_init() to allow i2c_init operations to setup the i2c bus
+ controller on the CPU (e.g. setting bus speed & slave address).
+
CONFIG_I2CFAST (PPC405GP|PPC405EP only)
This option enables configuration of bi_iic_fast[] flags
15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
- -30 arch/ppc/lib/board.c Fatal error, hang the system
+ -30 arch/powerpc/lib/board.c Fatal error, hang the system
-31 post/post.c POST test failed, detected by post_output_backlog()
-32 post/post.c POST test failed, detected by post_run_single()
I2C muxes, you can define here, how to reach this
EEPROM. For example:
- #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
+ #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
EEPROM which holds the environment, is reached over
a pca9547 i2c mux with address 0x70, channel 3.
Please note that the environment is read-only until the monitor
has been relocated to RAM and a RAM copy of the environment has been
-created; also, when using EEPROM you will have to use getenv_r()
+created; also, when using EEPROM you will have to use getenv_f()
until then to read environment variables.
The environment is protected by a CRC32 checksum. Before the monitor
CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
- Overrides the default PCI memory map in arch/ppc/cpu/mpc8260/pci.c if set.
+ Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
- CONFIG_PCI_DISABLE_PCIE:
Disable PCI-Express on systems where it is supported but not
interface is currently active. For example you
can do the following
- => setenv ethact FEC ETHERNET
- => ping 192.168.0.1 # traffic sent on FEC ETHERNET
- => setenv ethact SCC ETHERNET
- => ping 10.0.0.1 # traffic sent on SCC ETHERNET
+ => setenv ethact FEC
+ => ping 192.168.0.1 # traffic sent on FEC
+ => setenv ethact SCC
+ => ping 10.0.0.1 # traffic sent on SCC
ethrotate - When set to "no" U-Boot does not go through all
available network interfaces.
o If neither SROM nor the environment contain a MAC address, an error
is raised.
+If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
+will be programmed into hardware as part of the initialization process. This
+may be skipped by setting the appropriate 'ethmacskip' environment variable.
+The naming convention is as follows:
+"ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
Image Formats:
==============
Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
INTEGRITY).
* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
- IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
- Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC).
+ IA64, MIPS, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
+ Currently supported: ARM, AVR32, Intel x86, MIPS, Nios II, PowerPC).
* Compression Type (uncompressed, gzip, bzip2)
* Load Address
* Entry Point
(no, we don't intend to provide a full virtual machine interface to
Linux :-).
-But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
+But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
Just make sure your machine specific header file (for instance
include/asm-ppc/tqm8xx.h) includes the same definition of the Board
-> tools/mkimage -n '2.4.4 kernel for TQM850L' \
> -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
- > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
+ > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
> examples/uImage.TQM850L
Image Name: 2.4.4 kernel for TQM850L
Created: Wed Jul 19 02:34:59 2000
needs more space in Flash, but boots much faster since it does not
need to be uncompressed:
- -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
+ -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
-> tools/mkimage -n '2.4.4 kernel for TQM850L' \
> -A ppc -O linux -T kernel -C none -a 0 -e 0 \
- > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
+ > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
> examples/uImage.TQM850L-uncompressed
Image Name: 2.4.4 kernel for TQM850L
Created: Wed Jul 19 02:34:59 2000
==> U-Boot will use R8 to hold a pointer to the global data
+On Nios II, the ABI is documented here:
+ http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
+
+ ==> U-Boot will use gp to hold a pointer to the global data
+
+ Note: on Nios II, we give "-G0" option to gcc and don't use gp
+ to access small data sections, so gp is free.
+
NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
or current versions of GCC may "optimize" the code too much.
projects / karo-tx-uboot.git / blobdiff