ldr pc, _software_interrupt
ldr pc, _prefetch_abort
ldr pc, _data_abort
-#ifdef CONFIG_LPC2292
- .word 0xB4405F76 /* 2's complement of the checksum of the vectors */
-#else
ldr pc, _not_used
-#endif
ldr pc, _irq
ldr pc, _fiq
bl cpu_init_crit
#endif
-#ifdef CONFIG_LPC2292
- bl lowlevel_init
-#endif
-
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
- bl coloured_LED_init
- bl red_led_on
-#endif
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
mov pc, lr
-_board_init_r_ofs:
- .word board_init_r - _start
-
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
/*
*************************************************************************
*
*************************************************************************
*/
-#if defined(CONFIG_LPC2292)
-PLLCFG_ADR: .word PLLCFG
-PLLFEED_ADR: .word PLLFEED
-PLLCON_ADR: .word PLLCON
-PLLSTAT_ADR: .word PLLSTAT
-VPBDIV_ADR: .word VPBDIV
-MEMMAP_ADR: .word MEMMAP
-
-#endif
-
cpu_init_crit:
-#if defined(CONFIG_NETARM)
- /*
- * prior to software reset : need to set pin PORTC4 to be *HRESET
- */
- ldr r0, =NETARM_GEN_MODULE_BASE
- ldr r1, =(NETARM_GEN_PORT_MODE(0x10) | \
- NETARM_GEN_PORT_DIR(0x10))
- str r1, [r0, #+NETARM_GEN_PORTC]
- /*
- * software reset : see HW Ref. Guide 8.2.4 : Software Service register
- * for an explanation of this process
- */
- ldr r0, =NETARM_GEN_MODULE_BASE
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
- /*
- * setup PLL and System Config
- */
- ldr r0, =NETARM_GEN_MODULE_BASE
-
- ldr r1, =( NETARM_GEN_SYS_CFG_LENDIAN | \
- NETARM_GEN_SYS_CFG_BUSFULL | \
- NETARM_GEN_SYS_CFG_USER_EN | \
- NETARM_GEN_SYS_CFG_ALIGN_ABORT | \
- NETARM_GEN_SYS_CFG_BUSARB_INT | \
- NETARM_GEN_SYS_CFG_BUSMON_EN )
-
- str r1, [r0, #+NETARM_GEN_SYSTEM_CONTROL]
-
-#ifndef CONFIG_NETARM_PLL_BYPASS
- ldr r1, =( NETARM_GEN_PLL_CTL_PLLCNT(NETARM_PLL_COUNT_VAL) | \
- NETARM_GEN_PLL_CTL_POLTST_DEF | \
- NETARM_GEN_PLL_CTL_INDIV(1) | \
- NETARM_GEN_PLL_CTL_ICP_DEF | \
- NETARM_GEN_PLL_CTL_OUTDIV(2) )
- str r1, [r0, #+NETARM_GEN_PLL_CONTROL]
-#endif
-
- /*
- * mask all IRQs by clearing all bits in the INTMRs
- */
- mov r1, #0
- ldr r0, =NETARM_GEN_MODULE_BASE
- str r1, [r0, #+NETARM_GEN_INTR_ENABLE]
-#elif defined(CONFIG_S3C4510B)
-
- /*
- * Mask off all IRQ sources
- */
- ldr r1, =REG_INTMASK
- ldr r0, =0x3FFFFF
- str r0, [r1]
-
- /*
- * Disable Cache
- */
- ldr r0, =REG_SYSCFG
- ldr r1, =0x83ffffa0 /* cache-disabled */
- str r1, [r0]
-
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* No specific initialisation for IntegratorAP/CM720T as yet */
-#elif defined(CONFIG_LPC2292)
- /* Set-up PLL */
- mov r3, #0xAA
- mov r4, #0x55
- /* First disconnect and disable the PLL */
- ldr r0, PLLCON_ADR
- mov r1, #0x00
- str r1, [r0]
- ldr r0, PLLFEED_ADR /* start feed sequence */
- str r3, [r0]
- str r4, [r0] /* feed sequence done */
- /* Set new M and P values */
- ldr r0, PLLCFG_ADR
- mov r1, #0x23 /* M=4 and P=2 */
- str r1, [r0]
- ldr r0, PLLFEED_ADR /* start feed sequence */
- str r3, [r0]
- str r4, [r0] /* feed sequence done */
- /* Then enable the PLL */
- ldr r0, PLLCON_ADR
- mov r1, #0x01 /* PLL enable bit */
- str r1, [r0]
- ldr r0, PLLFEED_ADR /* start feed sequence */
- str r3, [r0]
- str r4, [r0] /* feed sequence done */
- /* Wait for the lock */
- ldr r0, PLLSTAT_ADR
- mov r1, #0x400 /* lock bit */
-lock_loop:
- ldr r2, [r0]
- and r2, r1, r2
- cmp r2, #0
- beq lock_loop
- /* And finally connect the PLL */
- ldr r0, PLLCON_ADR
- mov r1, #0x03 /* PLL enable bit and connect bit */
- str r1, [r0]
- ldr r0, PLLFEED_ADR /* start feed sequence */
- str r3, [r0]
- str r4, [r0] /* feed sequence done */
- /* Set-up VPBDIV register */
- ldr r0, VPBDIV_ADR
- mov r1, #0x01 /* VPB clock is same as process clock */
- str r1, [r0]
-#elif defined(CONFIG_TEGRA)
- /* No cpu_init_crit for tegra as yet */
-#else
-#error No cpu_init_crit() defined for current CPU type
-#endif
-
-#ifdef CONFIG_ARM7_REVD
- /* set clock speed */
- /* !!! we run @ 36 MHz due to a hardware flaw in Rev. D processors */
- /* !!! not doing DRAM refresh properly! */
- ldr r0, SYSCON3
- ldr r1, [r0]
- bic r1, r1, #CLKCTL
- orr r1, r1, #CLKCTL_36
- str r1, [r0]
-#endif
-
-#if !defined(CONFIG_LPC2292) && !defined(CONFIG_TEGRA)
+#if !defined(CONFIG_TEGRA)
mov ip, lr
/*
* before relocating, we have to setup RAM timing
#endif
#endif /* CONFIG_SPL_BUILD */
-
-#if defined(CONFIG_NETARM)
- .align 5
-.globl reset_cpu
-reset_cpu:
- ldr r1, =NETARM_MEM_MODULE_BASE
- ldr r0, [r1, #+NETARM_MEM_CS0_BASE_ADDR]
- ldr r1, =0xFFFFF000
- and r0, r1, r0
- ldr r1, =(relocate-CONFIG_SYS_TEXT_BASE)
- add r0, r1, r0
- ldr r4, =NETARM_GEN_MODULE_BASE
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETA
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- ldr r1, =NETARM_GEN_SW_SVC_RESETB
- str r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
- mov pc, r0
-#elif defined(CONFIG_S3C4510B)
-/* Nothing done here as reseting the CPU is board specific, depending
- * on external peripherals such as watchdog timers, etc. */
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
- /* No specific reset actions for IntegratorAP/CM720T as yet */
-#elif defined(CONFIG_LPC2292)
- .align 5
-.globl reset_cpu
-reset_cpu:
- mov pc, r0
-#elif defined(CONFIG_TEGRA)
- /* No specific reset actions for tegra as yet */
-#else
-#error No reset_cpu() defined for current CPU type
-#endif
projects / karo-tx-uboot.git / blobdiff