*/
#include <common.h>
+#include <asm/armv7.h>
+#include <asm/pl310.h>
#include <asm/errno.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
if (type != MXC_CPU_MX6SL) {
reg = readl(&anatop->digprog);
+ struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
+ u32 cfg = readl(&scu->config) & 3;
type = ((reg >> 16) & 0xff);
if (type == MXC_CPU_MX6DL) {
- struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
- u32 cfg = readl(&scu->config) & 3;
-
if (!cfg)
type = MXC_CPU_MX6SOLO;
}
+
+ if (type == MXC_CPU_MX6Q) {
+ if (cfg == 1)
+ type = MXC_CPU_MX6D;
+ }
+
}
reg &= 0xff; /* mx6 silicon revision */
return (type << 12) | (reg + 0x10);
if (type == MXC_CPU_MX6SOLO)
cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF);
+ if (type == MXC_CPU_MX6D)
+ cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF);
+
return cpurev;
}
#endif
void init_aips(void)
{
struct aipstz_regs *aips1, *aips2;
+#ifdef CONFIG_MX6SX
+ struct aipstz_regs *aips3;
+#endif
aips1 = (struct aipstz_regs *)AIPS1_BASE_ADDR;
aips2 = (struct aipstz_regs *)AIPS2_BASE_ADDR;
+#ifdef CONFIG_MX6SX
+ aips3 = (struct aipstz_regs *)AIPS3_BASE_ADDR;
+#endif
/*
* Set all MPROTx to be non-bufferable, trusted for R/W,
writel(0x00000000, &aips2->opacr2);
writel(0x00000000, &aips2->opacr3);
writel(0x00000000, &aips2->opacr4);
+
+#ifdef CONFIG_MX6SX
+ /*
+ * Set all MPROTx to be non-bufferable, trusted for R/W,
+ * not forced to user-mode.
+ */
+ writel(0x77777777, &aips3->mprot0);
+ writel(0x77777777, &aips3->mprot1);
+
+ /*
+ * Set all OPACRx to be non-bufferable, not require
+ * supervisor privilege level for access,allow for
+ * write access and untrusted master access.
+ */
+ writel(0x00000000, &aips3->opacr0);
+ writel(0x00000000, &aips3->opacr1);
+ writel(0x00000000, &aips3->opacr2);
+ writel(0x00000000, &aips3->opacr3);
+ writel(0x00000000, &aips3->opacr4);
+#endif
}
static void clear_ldo_ramp(void)
}
/*
- * Set the VDDSOC
+ * Set the PMU_REG_CORE register
*
- * Mask out the REG_CORE[22:18] bits (REG2_TRIG) and set
- * them to the specified millivolt level.
+ * Set LDO_SOC/PU/ARM regulators to the specified millivolt level.
* Possible values are from 0.725V to 1.450V in steps of
* 0.025V (25mV).
*/
writew(enable, &wdog2->wmcr);
}
+static void set_ahb_rate(u32 val)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ u32 reg, div;
+
+ div = get_periph_clk() / val - 1;
+ reg = readl(&mxc_ccm->cbcdr);
+
+ writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) |
+ (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr);
+}
+
+static void clear_mmdc_ch_mask(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* Clear MMDC channel mask */
+ writel(0, &mxc_ccm->ccdr);
+}
+
int arch_cpu_init(void)
{
init_aips();
+ /* Need to clear MMDC_CHx_MASK to make warm reset work. */
+ clear_mmdc_ch_mask();
+
+ /*
+ * When low freq boot is enabled, ROM will not set AHB
+ * freq, so we need to ensure AHB freq is 132MHz in such
+ * scenario.
+ */
+ if (mxc_get_clock(MXC_ARM_CLK) == 396000000)
+ set_ahb_rate(132000000);
+
imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */
#ifdef CONFIG_APBH_DMA
writel(reg, &mxc_ccm->chsccdr);
}
#endif
+
+#ifndef CONFIG_SYS_L2CACHE_OFF
+#define IOMUXC_GPR11_L2CACHE_AS_OCRAM 0x00000002
+void v7_outer_cache_enable(void)
+{
+ struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
+ unsigned int val;
+
+#if defined CONFIG_MX6SL
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ val = readl(&iomux->gpr[11]);
+ if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) {
+ /* L2 cache configured as OCRAM, reset it */
+ val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM;
+ writel(val, &iomux->gpr[11]);
+ }
+#endif
+
+ writel(0x132, &pl310->pl310_tag_latency_ctrl);
+ writel(0x132, &pl310->pl310_data_latency_ctrl);
+
+ val = readl(&pl310->pl310_prefetch_ctrl);
+
+ /* Turn on the L2 I/D prefetch */
+ val |= 0x30000000;
+
+ /*
+ * The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
+ * The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
+ * But according to ARM PL310 errata: 752271
+ * ID: 752271: Double linefill feature can cause data corruption
+ * Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
+ * Workaround: The only workaround to this erratum is to disable the
+ * double linefill feature. This is the default behavior.
+ */
+
+#ifndef CONFIG_MX6Q
+ val |= 0x40800000;
+#endif
+ writel(val, &pl310->pl310_prefetch_ctrl);
+
+ val = readl(&pl310->pl310_power_ctrl);
+ val |= L2X0_DYNAMIC_CLK_GATING_EN;
+ val |= L2X0_STNDBY_MODE_EN;
+ writel(val, &pl310->pl310_power_ctrl);
+
+ setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+}
+
+void v7_outer_cache_disable(void)
+{
+ struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
+
+ clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+}
+#endif /* !CONFIG_SYS_L2CACHE_OFF */