#include <asm-offsets.h>
#include <config.h>
#include <version.h>
+#include <asm/system.h>
+#include <linux/linkage.h>
.globl _start
_start: b reset
_TEXT_BASE:
.word CONFIG_SYS_TEXT_BASE
-#ifdef CONFIG_TEGRA2
-/*
- * Tegra2 uses 2 separate CPUs - the AVP (ARM7TDMI) and the CPU (dual A9s).
- * U-Boot runs on the AVP first, setting things up for the CPU (PLLs,
- * muxes, clocks, clamps, etc.). Then the AVP halts, and expects the CPU
- * to pick up its reset vector, which points here.
- */
-.globl _armboot_start
-_armboot_start:
- .word _start
-#endif
-
/*
* These are defined in the board-specific linker script.
*/
.globl _bss_end_ofs
_bss_end_ofs:
- .word __bss_end__ - _start
+ .word __bss_end - _start
.globl _end_ofs
_end_ofs:
orr r0, r0, #0xd3
msr cpsr,r0
-#if defined(CONFIG_OMAP34XX)
- /* Copy vectors to mask ROM indirect addr */
- adr r0, _start @ r0 <- current position of code
- add r0, r0, #4 @ skip reset vector
- mov r2, #64 @ r2 <- size to copy
- add r2, r0, r2 @ r2 <- source end address
- mov r1, #SRAM_OFFSET0 @ build vect addr
- mov r3, #SRAM_OFFSET1
- add r1, r1, r3
- mov r3, #SRAM_OFFSET2
- add r1, r1, r3
-next:
- ldmia r0!, {r3 - r10} @ copy from source address [r0]
- stmia r1!, {r3 - r10} @ copy to target address [r1]
- cmp r0, r2 @ until source end address [r2]
- bne next @ loop until equal */
-#if !defined(CONFIG_SYS_NAND_BOOT) && !defined(CONFIG_SYS_ONENAND_BOOT)
- /* No need to copy/exec the clock code - DPLL adjust already done
- * in NAND/oneNAND Boot.
- */
- bl cpy_clk_code @ put dpll adjust code behind vectors
-#endif /* NAND Boot */
+/*
+ * Setup vector:
+ * (OMAP4 spl TEXT_BASE is not 32 byte aligned.
+ * Continue to use ROM code vector only in OMAP4 spl)
+ */
+#if !(defined(CONFIG_OMAP44XX) && defined(CONFIG_SPL_BUILD))
+ /* Set V=0 in CP15 SCTRL register - for VBAR to point to vector */
+ mrc p15, 0, r0, c1, c0, 0 @ Read CP15 SCTRL Register
+ bic r0, #CR_V @ V = 0
+ mcr p15, 0, r0, c1, c0, 0 @ Write CP15 SCTRL Register
+
+ /* Set vector address in CP15 VBAR register */
+ ldr r0, =_start
+ mcr p15, 0, r0, c12, c0, 0 @Set VBAR
#endif
+
/* the mask ROM code should have PLL and others stable */
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+ bl cpu_init_cp15
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
+#ifndef CONFIG_SPL_BUILD
/*
* void relocate_code (addr_sp, gd, addr_moni)
*
* after relocating the monitor code.
*
*/
- .globl relocate_code
-relocate_code:
+ENTRY(relocate_code)
mov r4, r0 /* save addr_sp */
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _image_copy_end_ofs
add r2, r0, r3 /* r2 <- source end address */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
-#ifndef CONFIG_SPL_BUILD
/*
* fix .rel.dyn relocations
*/
add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
- b clear_bss
+
+relocate_done:
+
+ bx lr
+
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
.word __rel_dyn_end - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
+ENDPROC(relocate_code)
-#endif /* #ifndef CONFIG_SPL_BUILD */
-
-clear_bss:
-#ifdef CONFIG_SPL_BUILD
- /* No relocation for SPL */
- ldr r0, =__bss_start
- ldr r1, =__bss_end__
-#else
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
#endif
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
- add r0, r0, #4
- cmp r0, r1
- bne clbss_l
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-jump_2_ram:
+ENTRY(c_runtime_cpu_setup)
/*
* If I-cache is enabled invalidate it
*/
mcr p15, 0, r0, c7, c10, 4 @ DSB
mcr p15, 0, r0, c7, c5, 4 @ ISB
#endif
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
+/*
+ * Move vector table
+ */
+#if !defined(CONFIG_TEGRA)
+ /* Set vector address in CP15 VBAR register */
+ ldr r0, =_start
+ add r0, r0, r9
+ mcr p15, 0, r0, c12, c0, 0 @Set VBAR
+#endif /* !Tegra */
-_board_init_r_ofs:
- .word board_init_r - _start
+ bx lr
+ENDPROC(c_runtime_cpu_setup)
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
/*************************************************************************
*
- * CPU_init_critical registers
+ * void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3)
+ * __attribute__((weak));
*
- * setup important registers
- * setup memory timing
+ * Stack pointer is not yet initialized at this moment
+ * Don't save anything to stack even if compiled with -O0
+ *
+ *************************************************************************/
+ENTRY(save_boot_params)
+ bx lr @ back to my caller
+ENDPROC(save_boot_params)
+ .weak save_boot_params
+
+/*************************************************************************
+ *
+ * cpu_init_cp15
+ *
+ * Setup CP15 registers (cache, MMU, TLBs). The I-cache is turned on unless
+ * CONFIG_SYS_ICACHE_OFF is defined.
*
*************************************************************************/
-cpu_init_crit:
+ENTRY(cpu_init_cp15)
/*
* Invalidate L1 I/D
*/
#endif
mcr p15, 0, r0, c1, c0, 0
+#ifdef CONFIG_ARM_ERRATA_742230
+ mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register
+ orr r0, r0, #1 << 4 @ set bit #4
+ mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
+#endif
+
+#ifdef CONFIG_ARM_ERRATA_743622
+ mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register
+ orr r0, r0, #1 << 6 @ set bit #6
+ mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
+#endif
+
+#ifdef CONFIG_ARM_ERRATA_751472
+ mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register
+ orr r0, r0, #1 << 11 @ set bit #11
+ mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
+#endif
+
+ mov pc, lr @ back to my caller
+ENDPROC(cpu_init_cp15)
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+/*************************************************************************
+ *
+ * CPU_init_critical registers
+ *
+ * setup important registers
+ * setup memory timing
+ *
+ *************************************************************************/
+ENTRY(cpu_init_crit)
/*
* Jump to board specific initialization...
* The Mask ROM will have already initialized
* basic memory. Go here to bump up clock rate and handle
* wake up conditions.
*/
- mov ip, lr @ persevere link reg across call
- bl lowlevel_init @ go setup pll,mux,memory
- mov lr, ip @ restore link
- mov pc, lr @ back to my caller
+ b lowlevel_init @ go setup pll,mux,memory
+ENDPROC(cpu_init_crit)
#endif
#ifndef CONFIG_SPL_BUILD
projects / karo-tx-uboot.git / blobdiff