x86: fsp: Enlarge the size of malloc() pool before relocation

[karo-tx-uboot.git] / arch / x86 / Kconfig

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index b52a80e1c2017215766723bc3bbce1e04657bf49..687208fb3001f050fb589015986ad1df00d78458 100644 (file)
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -11,6 +11,9 @@ choice
 config VENDOR_COREBOOT
        bool "coreboot"
 
+config VENDOR_EFI
+       bool "efi"
+
 config VENDOR_EMULATION
        bool "emulation"
 
@@ -24,6 +27,7 @@ endchoice
 
 # board-specific options below
 source "board/coreboot/Kconfig"
+source "board/efi/Kconfig"
 source "board/emulation/Kconfig"
 source "board/google/Kconfig"
 source "board/intel/Kconfig"
@@ -188,16 +192,9 @@ config X86_RAMTEST
          to work correctly. It is not exhaustive but can save time by
          detecting obvious failures.
 
-config MARK_GRAPHICS_MEM_WRCOMB
-       bool "Mark graphics memory as write-combining"
-       default n
-       help
-         The graphics performance may increase if the graphics
-         memory is set as write-combining cache type. This option
-         enables marking the graphics memory as write-combining.
-
 config HAVE_FSP
        bool "Add an Firmware Support Package binary"
+       depends on !EFI
        help
          Select this option to add an Firmware Support Package binary to
          the resulting U-Boot image. It is a binary blob which U-Boot uses
@@ -235,6 +232,13 @@ config FSP_TEMP_RAM_ADDR
          Stack top address which is used in FspInit after DRAM is ready and
          CAR is disabled.
 
+config FSP_SYS_MALLOC_F_LEN
+       hex
+       depends on HAVE_FSP
+       default 0x100000
+       help
+         Additional size of malloc() pool before relocation.
+
 config SMP
        bool "Enable Symmetric Multiprocessing"
        default n
@@ -287,7 +291,30 @@ config TSC_FREQ_IN_MHZ
        help
          The running frequency in MHz of Time-Stamp Counter (TSC).
 
+config HAVE_VGA_BIOS
+       bool "Add a VGA BIOS image"
+       help
+         Select this option if you have a VGA BIOS image that you would
+         like to add to your ROM.
+
+config VGA_BIOS_FILE
+       string "VGA BIOS image filename"
+       depends on HAVE_VGA_BIOS
+       default "vga.bin"
+       help
+         The filename of the VGA BIOS image in the board directory.
+
+config VGA_BIOS_ADDR
+       hex "VGA BIOS image location"
+       depends on HAVE_VGA_BIOS
+       default 0xfff90000
+       help
+         The location of VGA BIOS image in the SPI flash. For example, base
+         address of 0xfff90000 indicates that the image will be put at offset
+         0x90000 from the beginning of a 1MB flash device.
+
 menu "System tables"
+       depends on !EFI && !SYS_COREBOOT
 
 config GENERATE_PIRQ_TABLE
        bool "Generate a PIRQ table"
@@ -355,4 +382,16 @@ config PCIE_ECAM_BASE
          assigned to PCI devices - i.e. the memory and prefetch regions, as
          passed to pci_set_region().
 
+config PCIE_ECAM_SIZE
+       hex
+       default 0x10000000
+       help
+         This is the size of memory-mapped address of PCI configuration space,
+         which is only available through the Enhanced Configuration Access
+         Mechanism (ECAM) with PCI Express. Each bus consumes 1 MiB memory,
+         so a default 0x10000000 size covers all of the 256 buses which is the
+         maximum number of PCI buses as defined by the PCI specification.
+
+source "arch/x86/lib/efi/Kconfig"
+
 endmenu