#include <asm/arch/at91sam9263.h>
#include <asm/arch/at91sam9263_matrix.h>
#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
+#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
#include <lcd.h>
#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
+#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
* Miscelaneous platform dependent initialisations
*/
-static void at91sam9263ek_serial_hw_init(void)
-{
-#ifdef CONFIG_USART0
- at91_set_A_periph(AT91_PIN_PA26, 1); /* TXD0 */
- at91_set_A_periph(AT91_PIN_PA27, 0); /* RXD0 */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US0);
-#endif
-
-#ifdef CONFIG_USART1
- at91_set_A_periph(AT91_PIN_PD0, 1); /* TXD1 */
- at91_set_A_periph(AT91_PIN_PD1, 0); /* RXD1 */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US1);
-#endif
-
-#ifdef CONFIG_USART2
- at91_set_A_periph(AT91_PIN_PD2, 1); /* TXD2 */
- at91_set_A_periph(AT91_PIN_PD3, 0); /* RXD2 */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US2);
-#endif
-
-#ifdef CONFIG_USART3 /* DBGU */
- at91_set_A_periph(AT91_PIN_PC30, 0); /* DRXD */
- at91_set_A_periph(AT91_PIN_PC31, 1); /* DTXD */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_SYS);
-#endif
-}
-
#ifdef CONFIG_CMD_NAND
static void at91sam9263ek_nand_hw_init(void)
{
/* Configure SMC CS3 for NAND/SmartMedia */
at91_sys_write(AT91_SMC_SETUP(3),
- AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
+ AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
+ AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
at91_sys_write(AT91_SMC_PULSE(3),
AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
at91_sys_write(AT91_SMC_MODE(3),
AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
AT91_SMC_EXNWMODE_DISABLE |
-#ifdef CFG_NAND_DBW_16
+#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_DBW_16 |
-#else /* CFG_NAND_DBW_8 */
+#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_DBW_8 |
#endif
AT91_SMC_TDF_(2));
1 << AT91SAM9263_ID_PIOCDE);
/* Configure RDY/BSY */
- at91_set_gpio_input(AT91_PIN_PA22, 1);
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
- at91_set_gpio_output(AT91_PIN_PD15, 1);
-}
-#endif
-
-#ifdef CONFIG_HAS_DATAFLASH
-static void at91sam9263ek_spi_hw_init(void)
-{
- at91_set_B_periph(AT91_PIN_PA5, 0); /* SPI0_NPCS0 */
-
- at91_set_B_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */
- at91_set_B_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */
- at91_set_B_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */
-
- /* Enable clock */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_SPI0);
+ at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif
#ifdef CONFIG_MACB
static void at91sam9263ek_macb_hw_init(void)
{
+ unsigned long rstc;
+
/* Enable clock */
at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_EMAC);
pin_to_mask(AT91_PIN_PE26),
pin_to_controller(AT91_PIN_PE0) + PIO_PUDR);
+ rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
+
/* Need to reset PHY -> 500ms reset */
at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
- AT91_RSTC_ERSTL | (0x0D << 8) |
+ (AT91_RSTC_ERSTL & (0x0D << 8)) |
AT91_RSTC_URSTEN);
at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
/* Wait for end hardware reset */
while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
+ /* Restore NRST value */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (rstc) |
+ AT91_RSTC_URSTEN);
+
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PC25),
pin_to_controller(AT91_PIN_PC0) + PIO_PUER);
pin_to_mask(AT91_PIN_PE26),
pin_to_controller(AT91_PIN_PE0) + PIO_PUER);
- at91_set_A_periph(AT91_PIN_PE21, 0); /* ETXCK_EREFCK */
- at91_set_B_periph(AT91_PIN_PC25, 0); /* ERXDV */
- at91_set_A_periph(AT91_PIN_PE25, 0); /* ERX0 */
- at91_set_A_periph(AT91_PIN_PE26, 0); /* ERX1 */
- at91_set_A_periph(AT91_PIN_PE27, 0); /* ERXER */
- at91_set_A_periph(AT91_PIN_PE28, 0); /* ETXEN */
- at91_set_A_periph(AT91_PIN_PE23, 0); /* ETX0 */
- at91_set_A_periph(AT91_PIN_PE24, 0); /* ETX1 */
- at91_set_A_periph(AT91_PIN_PE30, 0); /* EMDIO */
- at91_set_A_periph(AT91_PIN_PE29, 0); /* EMDC */
-
-#ifndef CONFIG_RMII
- at91_set_A_periph(AT91_PIN_PE22, 0); /* ECRS */
- at91_set_B_periph(AT91_PIN_PC26, 0); /* ECOL */
- at91_set_B_periph(AT91_PIN_PC22, 0); /* ERX2 */
- at91_set_B_periph(AT91_PIN_PC23, 0); /* ERX3 */
- at91_set_B_periph(AT91_PIN_PC27, 0); /* ERXCK */
- at91_set_B_periph(AT91_PIN_PC20, 0); /* ETX2 */
- at91_set_B_periph(AT91_PIN_PC21, 0); /* ETX3 */
- at91_set_B_periph(AT91_PIN_PC24, 0); /* ETXER */
-#endif
-
-}
-#endif
-
-#ifdef CONFIG_USB_OHCI_NEW
-static void at91sam9263ek_uhp_hw_init(void)
-{
- /* Enable VBus on UHP ports */
- at91_set_gpio_output(AT91_PIN_PA21, 0);
- at91_set_gpio_output(AT91_PIN_PA24, 0);
+ at91_macb_hw_init();
}
#endif
gd->fb_base = AT91SAM9263_SRAM0_BASE;
}
+
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+
+#ifndef CONFIG_SYS_NO_FLASH
+extern flash_info_t flash_info[];
+#endif
+
+void lcd_show_board_info(void)
+{
+ ulong dram_size, nand_size;
+#ifndef CONFIG_SYS_NO_FLASH
+ ulong flash_size;
+#endif
+ int i;
+ char temp[32];
+
+ lcd_printf ("%s\n", U_BOOT_VERSION);
+ lcd_printf ("(C) 2008 ATMEL Corp\n");
+ lcd_printf ("at91support@atmel.com\n");
+ lcd_printf ("%s CPU at %s MHz\n",
+ AT91_CPU_NAME,
+ strmhz(temp, get_cpu_clk_rate()));
+
+ dram_size = 0;
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+ dram_size += gd->bd->bi_dram[i].size;
+ nand_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+ nand_size += nand_info[i].size;
+#ifndef CONFIG_SYS_NO_FLASH
+ flash_size = 0;
+ for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
+ flash_size += flash_info[i].size;
+#endif
+ lcd_printf (" %ld MB SDRAM, %ld MB NAND",
+ dram_size >> 20,
+ nand_size >> 20 );
+#ifndef CONFIG_SYS_NO_FLASH
+ lcd_printf (",\n %ld MB NOR",
+ flash_size >> 20);
+#endif
+ lcd_puts ("\n");
+}
+#endif /* CONFIG_LCD_INFO */
#endif
int board_init(void)
/* adress of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- at91sam9263ek_serial_hw_init();
+ at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
at91sam9263ek_nand_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
- at91sam9263ek_spi_hw_init();
+ at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
+ at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
at91sam9263ek_macb_hw_init();
#endif
#ifdef CONFIG_USB_OHCI_NEW
- at91sam9263ek_uhp_hw_init();
+ at91_uhp_hw_init();
#endif
#ifdef CONFIG_LCD
at91sam9263ek_lcd_hw_init();
#endif
}
#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)AT91SAM9263_BASE_EMAC, 0x00);
+#endif
+ return rc;
+}
projects / karo-tx-uboot.git / blobdiff