#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_rstc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
#include <atmel_lcdc.h>
+#include <atmel_mci.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
- struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
- unsigned long erstl;
/* Enable clock */
writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
pin_to_mask(AT91_PIN_PA13),
&pioa->pudr);
- erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
-
- /* Need to reset PHY -> 500ms reset */
- writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(13) |
- AT91_RSTC_MR_URSTEN, &rstc->mr);
-
- writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
-
- /* Wait for end hardware reset */
- while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL))
- ;
-
- /* Restore NRST value */
- writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN,
- &rstc->mr);
+ at91_phy_reset();
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PA15) |
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
- vl_col: 480,
- vl_row: 272,
- vl_clk: 9000000,
- vl_sync: ATMEL_LCDC_INVLINE_NORMAL |
- ATMEL_LCDC_INVFRAME_NORMAL,
- vl_bpix: 3,
- vl_tft: 1,
- vl_hsync_len: 45,
- vl_left_margin: 1,
- vl_right_margin:1,
- vl_vsync_len: 1,
- vl_upper_margin:40,
- vl_lower_margin:1,
- mmio : ATMEL_BASE_LCDC,
+ .vl_col = 480,
+ .vl_row = 272,
+ .vl_clk = 9000000,
+ .vl_sync = ATMEL_LCDC_INVLINE_NORMAL |
+ ATMEL_LCDC_INVFRAME_NORMAL,
+ .vl_bpix = 3,
+ .vl_tft = 1,
+ .vl_hsync_len = 45,
+ .vl_left_margin = 1,
+ .vl_right_margin = 1,
+ .vl_vsync_len = 1,
+ .vl_upper_margin = 40,
+ .vl_lower_margin = 1,
+ .mmio = ATMEL_BASE_LCDC,
};
#endif /* CONFIG_LCD_INFO */
#endif
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+int board_mmc_init(bd_t *bis)
+{
+ at91_mci_hw_init();
+
+ return atmel_mci_init((void *)ATMEL_BASE_MCI0);
+}
+#endif
+
int board_early_init_f(void)
{
at91_seriald_hw_init();