sama5d3xek: run PHY's config

[karo-tx-uboot.git] / board / atmel / sama5d3xek / sama5d3xek.c

diff --git a/board/atmel/sama5d3xek/sama5d3xek.c b/board/atmel/sama5d3xek/sama5d3xek.c
index 8a214de475a11d5b10eddfd5de144961caaaa643..ca4f79ddc1f6feb708424032864e40e8271ff4b0 100644 (file)
--- a/board/atmel/sama5d3xek/sama5d3xek.c
+++ b/board/atmel/sama5d3xek/sama5d3xek.c
@@ -17,6 +17,7 @@
 #include <lcd.h>
 #include <atmel_lcdc.h>
 #include <atmel_mci.h>
+#include <phy.h>
 #include <micrel.h>
 #include <net.h>
 #include <netdev.h>
@@ -67,6 +68,61 @@ void sama5d3xek_nand_hw_init(void)
 }
 #endif
 
+#ifndef CONFIG_SYS_NO_FLASH
+static void sama5d3xek_nor_hw_init(void)
+{
+       struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+
+       at91_periph_clk_enable(ATMEL_ID_SMC);
+
+       /* Configure SMC CS0 for NOR flash */
+       writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+              AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+              &smc->cs[0].setup);
+       writel(AT91_SMC_PULSE_NWE(10) | AT91_SMC_PULSE_NCS_WR(11) |
+              AT91_SMC_PULSE_NRD(10) | AT91_SMC_PULSE_NCS_RD(11),
+              &smc->cs[0].pulse);
+       writel(AT91_SMC_CYCLE_NWE(11) | AT91_SMC_CYCLE_NRD(14),
+              &smc->cs[0].cycle);
+       writel(AT91_SMC_TIMINGS_TCLR(0) | AT91_SMC_TIMINGS_TADL(0)  |
+              AT91_SMC_TIMINGS_TAR(0)  | AT91_SMC_TIMINGS_TRR(0)   |
+              AT91_SMC_TIMINGS_TWB(0)  | AT91_SMC_TIMINGS_RBNSEL(0)|
+              AT91_SMC_TIMINGS_NFSEL(0), &smc->cs[0].timings);
+       writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+              AT91_SMC_MODE_EXNW_DISABLE |
+              AT91_SMC_MODE_DBW_16 |
+              AT91_SMC_MODE_TDF_CYCLE(1),
+              &smc->cs[0].mode);
+
+       /* Address pin (A1 ~ A23) configuration */
+       at91_set_a_periph(AT91_PIO_PORTE, 1, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 2, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 3, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 4, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 5, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 6, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 7, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 8, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 9, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 10, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 11, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 12, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 13, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 14, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 15, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 16, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 17, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 18, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 19, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 20, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 21, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 22, 0);
+       at91_set_a_periph(AT91_PIO_PORTE, 23, 0);
+       /* CS0 pin configuration */
+       at91_set_a_periph(AT91_PIO_PORTE, 26, 0);
+}
+#endif
+
 #ifdef CONFIG_CMD_USB
 static void sama5d3xek_usb_hw_init(void)
 {
@@ -181,6 +237,9 @@ int board_init(void)
 #ifdef CONFIG_NAND_ATMEL
        sama5d3xek_nand_hw_init();
 #endif
+#ifndef CONFIG_SYS_NO_FLASH
+       sama5d3xek_nor_hw_init();
+#endif
 #ifdef CONFIG_CMD_USB
        sama5d3xek_usb_hw_init();
 #endif
@@ -215,15 +274,25 @@ int dram_init(void)
 
 int board_phy_config(struct phy_device *phydev)
 {
-       /* rx data delay */
-       ksz9021_phy_extended_write(phydev,
-                                  MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, 0x2222);
-       /* tx data delay */
-       ksz9021_phy_extended_write(phydev,
-                                  MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW, 0x2222);
-       /* rx/tx clock delay */
-       ksz9021_phy_extended_write(phydev,
-                                  MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0xf2f4);
+       /* board specific timings for GMAC */
+       if (has_gmac()) {
+               /* rx data delay */
+               ksz9021_phy_extended_write(phydev,
+                                          MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
+                                          0x2222);
+               /* tx data delay */
+               ksz9021_phy_extended_write(phydev,
+                                          MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
+                                          0x2222);
+               /* rx/tx clock delay */
+               ksz9021_phy_extended_write(phydev,
+                                          MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
+                                          0xf2f4);
+       }
+
+       /* always run the PHY's config routine */
+       if (phydev->drv->config)
+               return phydev->drv->config(phydev);
 
        return 0;
 }
@@ -307,6 +376,8 @@ void spl_board_init(void)
 {
 #ifdef CONFIG_SYS_USE_MMC
        sama5d3xek_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+       sama5d3xek_nand_hw_init();
 #elif CONFIG_SYS_USE_SERIALFLASH
        at91_spi0_hw_init(1 << 0);
 #endif