Update from 2013.01 to 2013.07

[karo-tx-uboot.git] / board / bf609-ezkit / soft_switch.h

diff --git a/board/bf609-ezkit/soft_switch.h b/board/bf609-ezkit/soft_switch.h
new file mode 100644 (file)
index 0000000..d147fe1
--- /dev/null
+++ b/board/bf609-ezkit/soft_switch.h
@@ -0,0 +1,80 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2011 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __BOARD_SOFT_SWITCH_H__
+#define __BOARD_SOFT_SWITCH_H__
+
+#include <asm/soft_switch.h>
+
+/* switch 0 port A */
+#define CAN_EN                 0x1
+#define CAN_STB                0x2
+#define CAN0_ERR_EN            0x4
+#define CAN0RX_EN              0x8
+#define CNT0UD_EN              0x10
+#define CNT0DG_EN              0x20
+#define CNT0ZM_EN              0x40
+#define RMII_CLK_EN            0x80
+
+/* switch 0 port B */
+#define UART0RTS_EN            0x1
+#define UART0RX_EN             0x2
+#define UART0CTS_EN            0x4
+#define UART0CTS_RTS_LPBK      0x8
+#define UART0CTS_RST_EN        0x10
+#define UART0CTS_146_EN        0x20
+#define TEMP_IRQ_EN            0x40
+#define TEMP_THERM_EN          0x80
+
+/* switch 1 port A */
+#define OVERRIDE_SMC0_LP0_BOOT 0x1
+#define SMC0_EPPI2_LP1_SWITCH  0x2
+#define SMC0_LP0_EN            0x8
+#define LED1_GPIO_EN           0x10
+#define LED2_GPIO_EN           0x20
+#define LED3_GPIO_EN           0x40
+#define LED4_GPIO_EN           0x80
+
+/* switch 1 port B */
+#define PUSHBUTTON1_EN         0x1
+#define PUSHBUTTON2_EN         0x2
+#define SD_CD_EN               0x4
+#define SD_WP_EN               0x8
+#define SPIFLASH_CS_EN         0x10
+#define SPI0D2_EN              0x20
+#define SPI0D3_EN              0x40
+
+/* switch 2 port A */
+#define PHYINT_EN              0x1
+#define PHY_PWR_DWN_INT        0x2
+#define PHYAD0                 0x4
+#define ETHERNET_EN            0x8
+#define WAKE_PUSHBUTTON_EN     0x10
+#define PD0_SPI0D2_EN          0x20
+#define PD1_SPI0D3_EN          0x40
+#define PD2_SPI0MISO_EN        0x80
+
+/* switch 2 port B */
+#define PD3_SPI0MOSI_EN        0x1
+#define PD4_SPI0CK_EN          0x2
+
+#ifdef CONFIG_BFIN_BOARD_VERSION_1_0
+#define SWITCH_ADDR     0x21
+#else
+#define SWITCH_ADDR     0x20
+#endif
+
+#define NUM_SWITCH      3
+#define IODIRA          0x0
+#define IODIRB          0x1
+#define OLATA           0x14
+#define OLATB           0x15
+
+int setup_board_switches(void);
+
+#endif /* __BOARD_SOFT_SWITCH_H__ */