Update from 2013.01 to 2013.07

[karo-tx-uboot.git] / board / esg / ima3-mx53 / imximage.cfg

diff --git a/board/esg/ima3-mx53/imximage.cfg b/board/esg/ima3-mx53/imximage.cfg
index fa6b42ddcce9afba6527129d930e53c14f923c9c..324a90e9028592b9d4da1390cb058944a79c5621 100644 (file)
--- a/board/esg/ima3-mx53/imximage.cfg
+++ b/board/esg/ima3-mx53/imximage.cfg
@@ -1,50 +1,36 @@
-#
-# (C) Copyright 2012
-# Stefano Babic DENX Software Engineering sbabic@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not write to the Free Software
-# Foundation Inc. 51 Franklin Street Fifth Floor Boston,
-# MA 02110-1301 USA
-#
-# Refer docs/README.imxmage for more details about how-to configure
-# and create imximage boot image
-#
-# The syntax is taken as close as possible with the kwbimage
-
-# image version
+/*
+ * (C) Copyright 2012
+ * Stefano Babic DENX Software Engineering sbabic@denx.de.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
 
+/* image version */
 IMAGE_VERSION 2
 
-# Boot Device : one of
-# spi, sd (the board has no nand neither onenand)
-
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
 BOOT_FROM      nor
 
-# Device Configuration Data (DCD)
-#
-# Each entry must have the format:
-# Addr-type           Address        Value
-#
-# where:
-#      Addr-type register length (1,2 or 4 bytes)
-#      Address   absolute address of the register
-#      value     value to be stored in the register
-
-# IOMUX for RAM only
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *     Addr-type register length (1,2 or 4 bytes)
+ *     Address   absolute address of the register
+ *     value     value to be stored in the register
+ */
+/* IOMUX for RAM only */
 DATA 4 0x53fa8554 0x300020
 DATA 4 0x53fa8560 0x300020
 DATA 4 0x53fa8594 0x300020
@@ -72,37 +58,47 @@ DATA 4 0x53fa86fc 0x0
 DATA 4 0x53fa86f4 0x0
 DATA 4 0x53fa8714 0x0
 DATA 4 0x53fa8724 0x4000000
-#
-# DDR RAM
+
+/* DDR RAM */
 DATA 4 0x63fd9088 0x40404040
 DATA 4 0x63fd9090 0x40404040
 DATA 4 0x63fd907C 0x01420143
 DATA 4 0x63fd9080 0x01450146
 DATA 4 0x63fd9018 0x00111740
 DATA 4 0x63fd9000 0x84190000
-# esdcfgX
+
+/* esdcfgX */
 DATA 4 0x63fd900C 0x9f5152e3
 DATA 4 0x63fd9010 0xb68e8a63
 DATA 4 0x63fd9014 0x01ff00db
-# Read/Write command delay
+
+/* Read/Write command delay */
 DATA 4 0x63fd902c 0x000026d2
-# Out of reset delays
+
+/* Out of reset delays */
 DATA 4 0x63fd9030 0x00ff0e21
-# ESDCTL ODT timing control
+
+/* ESDCTL ODT timing control */
 DATA 4 0x63fd9008 0x12273030
-# ESDCTL power down control
+
+/* ESDCTL power down control */
 DATA 4 0x63fd9004 0x0002002d
-# Set registers in DDR memory chips
+
+/* Set registers in DDR memory chips */
 DATA 4 0x63fd901c 0x00008032
 DATA 4 0x63fd901c 0x00008033
 DATA 4 0x63fd901c 0x00028031
 DATA 4 0x63fd901c 0x052080b0
 DATA 4 0x63fd901c 0x04008040
-# ESDCTL refresh control
+
+/* ESDCTL refresh control */
 DATA 4 0x63fd9020 0x00005800
-# PHY ZQ HW control
+
+/* PHY ZQ HW control */
 DATA 4 0x63fd9040 0x05380003
-# PHY ODT control
+
+/* PHY ODT control */
 DATA 4 0x63fd9058 0x00022222
-# start DDR3
+
+/* start DDR3 */
 DATA 4 0x63fd901c 0x00000000