uchar tras_clocks;
uchar burst_len;
uchar banks, slot;
- int size; /* detected size, not from I2C but from dram_size() */
+ int size; /* detected size, not from I2C but from dram_size() */
} sdram_info_t;
#ifdef DEBUG
-void dump_dimm_info(struct sdram_info *d)
+void dump_dimm_info (struct sdram_info *d)
{
- static const char *ecc_legend[]={""," Parity"," ECC"};
- printf("dimm%s %sDRAM: %dMibytes:\n",
- ecc_legend[d->ecc],
- d->registered?"R":"",
- (d->size>>20));
- printf(" drb=%d tpar=%d tras=%d burstlen=%d banks=%d slot=%d\n",
- d->drb_size, d->tpar, d->tras_clocks, d->burst_len,
- d->banks, d->slot);
+ static const char *ecc_legend[] = { "", " Parity", " ECC" };
+
+ printf ("dimm%s %sDRAM: %dMibytes:\n",
+ ecc_legend[d->ecc],
+ d->registered ? "R" : "", (d->size >> 20));
+ printf (" drb=%d tpar=%d tras=%d burstlen=%d banks=%d slot=%d\n",
+ d->drb_size, d->tpar, d->tras_clocks, d->burst_len,
+ d->banks, d->slot);
}
#endif
static int
-memory_map_bank(unsigned int bankNo,
- unsigned int bankBase,
- unsigned int bankLength)
+memory_map_bank (unsigned int bankNo,
+ unsigned int bankBase, unsigned int bankLength)
{
#ifdef DEBUG
if (bankLength > 0) {
- printf("mapping bank %d at %08x - %08x\n",
- bankNo, bankBase, bankBase + bankLength - 1);
+ printf ("mapping bank %d at %08x - %08x\n",
+ bankNo, bankBase, bankBase + bankLength - 1);
} else {
- printf("unmapping bank %d\n", bankNo);
+ printf ("unmapping bank %d\n", bankNo);
}
#endif
- memoryMapBank(bankNo, bankBase, bankLength);
+ memoryMapBank (bankNo, bankBase, bankLength);
return 0;
}
#ifdef MAP_PCI
static int
-memory_map_bank_pci(unsigned int bankNo,
- unsigned int bankBase,
- unsigned int bankLength)
+memory_map_bank_pci (unsigned int bankNo,
+ unsigned int bankBase, unsigned int bankLength)
{
PCI_HOST host;
- for (host=PCI_HOST0;host<=PCI_HOST1;host++) {
- const int features=
+
+ for (host = PCI_HOST0; host <= PCI_HOST1; host++) {
+ const int features =
PREFETCH_ENABLE |
DELAYED_READ_ENABLE |
AGGRESSIVE_PREFETCH |
READ_LINE_AGGRESSIVE_PREFETCH |
READ_MULTI_AGGRESSIVE_PREFETCH |
- MAX_BURST_4 |
- PCI_NO_SWAP;
+ MAX_BURST_4 | PCI_NO_SWAP;
- pciMapMemoryBank(host, bankNo, bankBase, bankLength);
+ pciMapMemoryBank (host, bankNo, bankBase, bankLength);
- pciSetRegionSnoopMode(host, bankNo, PCI_SNOOP_WB, bankBase,
- bankLength);
+ pciSetRegionSnoopMode (host, bankNo, PCI_SNOOP_WB, bankBase,
+ bankLength);
- pciSetRegionFeatures(host, bankNo, features, bankBase, bankLength);
+ pciSetRegionFeatures (host, bankNo, features, bankBase,
+ bankLength);
}
return 0;
}
* translate ns.ns/10 coding of SPD timing values
* into 10 ps unit values
*/
-static inline unsigned short
-NS10to10PS(unsigned char spd_byte)
+static inline unsigned short NS10to10PS (unsigned char spd_byte)
{
unsigned short ns, ns10;
/* isolate lower nibble */
ns10 = (spd_byte & 0x0F);
- return(ns*100 + ns10*10);
+ return (ns * 100 + ns10 * 10);
}
/*
* translate ns coding of SPD timing values
* into 10 ps unit values
*/
-static inline unsigned short
-NSto10PS(unsigned char spd_byte)
+static inline unsigned short NSto10PS (unsigned char spd_byte)
{
- return(spd_byte*100);
+ return (spd_byte * 100);
}
#ifdef CONFIG_ZUMA_V2
-static int
-check_dimm(uchar slot, sdram_info_t *info)
+static int check_dimm (uchar slot, sdram_info_t * info)
{
/* assume 2 dimms, 2 banks each 256M - we dont have an
* dimm i2c so rely on the detection routines later */
- memset(info, 0, sizeof(*info));
+ memset (info, 0, sizeof (*info));
info->slot = slot;
info->banks = 2; /* Detect later */
- info->registered = 0;
+ info->registered = 0;
info->drb_size = 32; /* 16 - 256MBit, 32 - 512MBit
but doesn't matter, both do same
thing in setup_sdram() */
- info->tpar = 3;
- info->tras_clocks = 5;
- info->burst_len = 4;
+ info->tpar = 3;
+ info->tras_clocks = 5;
+ info->burst_len = 4;
#ifdef CONFIG_ECC
info->ecc = 0; /* Detect later */
#endif /* CONFIG_ECC */
#elif defined(CONFIG_P3G4)
-static int
-check_dimm(uchar slot, sdram_info_t *info)
+static int check_dimm (uchar slot, sdram_info_t * info)
{
- memset(info, 0, sizeof(*info));
+ memset (info, 0, sizeof (*info));
if (slot)
return 0;
return 0;
}
-#else /* ! CONFIG_ZUMA_V2 && ! CONFIG_P3G4*/
+#else /* ! CONFIG_ZUMA_V2 && ! CONFIG_P3G4 */
/* This code reads the SPD chip on the sdram and populates
* the array which is passed in with the relevant information */
-static int
-check_dimm(uchar slot, sdram_info_t *info)
+static int check_dimm (uchar slot, sdram_info_t * info)
{
DECLARE_GLOBAL_DATA_PTR;
uchar addr = slot == 0 ? DIMM0_I2C_ADDR : DIMM1_I2C_ADDR;
get_clocks ();
- tmemclk = 1000000000 / (gd->bus_clk / 100); /* in 10 ps units */
+ tmemclk = 1000000000 / (gd->bus_clk / 100); /* in 10 ps units */
#ifdef CONFIG_EVB64260_750CX
if (0 != slot) {
- printf("check_dimm: The EVB-64260-750CX only has 1 DIMM,");
- printf(" called with slot=%d insetad!\n", slot);
+ printf ("check_dimm: The EVB-64260-750CX only has 1 DIMM,");
+ printf (" called with slot=%d insetad!\n", slot);
return 0;
}
#endif
- DP(puts("before i2c read\n"));
+ DP (puts ("before i2c read\n"));
- ret = i2c_read(addr, 0, 128, data, 0);
+ ret = i2c_read (addr, 0, 128, data, 0);
- DP(puts("after i2c read\n"));
+ DP (puts ("after i2c read\n"));
/* zero all the values */
- memset(info, 0, sizeof(*info));
+ memset (info, 0, sizeof (*info));
if (ret) {
- DP(printf("No DIMM in slot %d [err = %x]\n", slot, ret));
+ DP (printf ("No DIMM in slot %d [err = %x]\n", slot, ret));
return 0;
}
/* first, do some sanity checks */
if (data[2] != 0x4) {
- printf("Not SDRAM in slot %d\n", slot);
+ printf ("Not SDRAM in slot %d\n", slot);
return 0;
}
sdram_banks = data[17];
width = data[13] & 0x7f;
- DP(printf("sdram_banks: %d, banks: %d\n", sdram_banks, info->banks));
+ DP (printf
+ ("sdram_banks: %d, banks: %d\n", sdram_banks, info->banks));
/* check if the memory is registered */
if (data[21] & (BIT1 | BIT4))
supp_cal = (data[18] & 0x6) >> 1;
/* compute the relevant clock values */
- trp_clocks = (NSto10PS(data[27])+(tmemclk-1)) / tmemclk;
- trcd_clocks = (NSto10PS(data[29])+(tmemclk-1)) / tmemclk;
- info->tras_clocks = (NSto10PS(data[30])+(tmemclk-1)) / tmemclk;
+ trp_clocks = (NSto10PS (data[27]) + (tmemclk - 1)) / tmemclk;
+ trcd_clocks = (NSto10PS (data[29]) + (tmemclk - 1)) / tmemclk;
+ info->tras_clocks = (NSto10PS (data[30]) + (tmemclk - 1)) / tmemclk;
- DP(printf("trp = %d\ntrcd_clocks = %d\ntras_clocks = %d\n",
- trp_clocks, trcd_clocks, info->tras_clocks));
+ DP (printf ("trp = %d\ntrcd_clocks = %d\ntras_clocks = %d\n",
+ trp_clocks, trcd_clocks, info->tras_clocks));
/* try a CAS latency of 3 first... */
cal_val = 0;
if (supp_cal & 3) {
- if (NS10to10PS(data[9]) <= tmemclk)
+ if (NS10to10PS (data[9]) <= tmemclk)
cal_val = 3;
}
/* then 2... */
if (supp_cal & 2) {
- if (NS10to10PS(data[23]) <= tmemclk)
+ if (NS10to10PS (data[23]) <= tmemclk)
cal_val = 2;
}
- DP(printf("cal_val = %d\n", cal_val));
+ DP (printf ("cal_val = %d\n", cal_val));
/* bummer, did't work... */
if (cal_val == 0) {
- DP(printf("Couldn't find a good CAS latency\n"));
+ DP (printf ("Couldn't find a good CAS latency\n"));
return 0;
}
if (trcd_clocks > info->tpar)
info->tpar = trcd_clocks;
- DP(printf("tpar set to: %d\n", info->tpar));
+ DP (printf ("tpar set to: %d\n", info->tpar));
#ifdef CFG_BROKEN_CL2
- if (info->tpar == 2){
+ if (info->tpar == 2) {
info->tpar = 3;
- DP(printf("tpar fixed-up to: %d\n", info->tpar));
+ DP (printf ("tpar fixed-up to: %d\n", info->tpar));
}
#endif
/* compute the module DRB size */
- info->drb_size = (((1 << (rows + cols)) * sdram_banks) * width) / _16M;
+ info->drb_size =
+ (((1 << (rows + cols)) * sdram_banks) * width) / _16M;
- DP(printf("drb_size set to: %d\n", info->drb_size));
+ DP (printf ("drb_size set to: %d\n", info->drb_size));
/* find the burst len */
info->burst_len = data[16] & 0xf;
}
#endif /* ! CONFIG_ZUMA_V2 */
-static int
-setup_sdram_common(sdram_info_t info[2])
+static int setup_sdram_common (sdram_info_t info[2])
{
ulong tmp;
- int tpar=2, tras_clocks=5, registered=1, ecc=2;
+ int tpar = 2, tras_clocks = 5, registered = 1, ecc = 2;
+
+ if (!info[0].banks && !info[1].banks)
+ return 0;
+
+ if (info[0].banks) {
+ if (info[0].tpar > tpar)
+ tpar = info[0].tpar;
+ if (info[0].tras_clocks > tras_clocks)
+ tras_clocks = info[0].tras_clocks;
+ if (!info[0].registered)
+ registered = 0;
+ if (info[0].ecc != 2indent: Standard input:491: Warning:old style assignment ambiguity in "=*". Assuming "= *"
- if(!info[0].banks && !info[1].banks) return 0;
+indent: Standard input:492: Warning:old style assignment ambiguity in "=*". Assuming "= *"
- if(info[0].banks) {
- if(info[0].tpar>tpar) tpar=info[0].tpar;
- if(info[0].tras_clocks>tras_clocks) tras_clocks=info[0].tras_clocks;
- if(!info[0].registered) registered=0;
- if(info[0].ecc!=2) ecc=0;
+)
+ ecc = 0;
}
- if(info[1].banks) {
- if(info[1].tpar>tpar) tpar=info[1].tpar;
- if(info[1].tras_clocks>tras_clocks) tras_clocks=info[1].tras_clocks;
- if(!info[1].registered) registered=0;
- if(info[1].ecc!=2) ecc=0;
+ if (info[1].banks) {
+ if (info[1].tpar > tpar)
+ tpar = info[1].tpar;
+ if (info[1].tras_clocks > tras_clocks)
+ tras_clocks = info[1].tras_clocks;
+ if (!info[1].registered)
+ registered = 0;
+ if (info[1].ecc != 2)
+ ecc = 0;
}
/* SDRAM configuration */
- tmp = GTREGREAD(SDRAM_CONFIGURATION);
+ tmp = GTREGREAD (SDRAM_CONFIGURATION);
/* Turn on physical interleave if both DIMMs
* have even numbers of banks. */
- if( (info[0].banks == 0 || info[0].banks == 2) &&
- (info[1].banks == 0 || info[1].banks == 2) ) {
- /* physical interleave on */
- tmp &= ~(1 << 15);
+ if ((info[0].banks == 0 || info[0].banks == 2) &&
+ (info[1].banks == 0 || info[1].banks == 2)) {
+ /* physical interleave on */
+ tmp &= ~(1 << 15);
} else {
- /* physical interleave off */
- tmp |= (1 << 15);
+ /* physical interleave off */
+ tmp |= (1 << 15);
}
tmp |= (registered << 17);
* See Res #12 */
tmp |= (1 << 26);
- GT_REG_WRITE(SDRAM_CONFIGURATION, tmp);
- DP(printf("SDRAM config: %08x\n",
- GTREGREAD(SDRAM_CONFIGURATION)));
+ GT_REG_WRITE (SDRAM_CONFIGURATION, tmp);
+ DP (printf ("SDRAM config: %08x\n", GTREGREAD (SDRAM_CONFIGURATION)));
/* SDRAM timing */
tmp = (((tpar == 3) ? 2 : 1) |
(((tpar == 3) ? 2 : 1) << 2) |
- (((tpar == 3) ? 2 : 1) << 4) |
- (tras_clocks << 8));
+ (((tpar == 3) ? 2 : 1) << 4) | (tras_clocks << 8));
#ifdef CONFIG_ECC
/* Setup ECC */
- if (ecc == 2) tmp |= 1<<13;
+ if (ecc == 2)
+ tmp |= 1 << 13;
#endif /* CONFIG_ECC */
- GT_REG_WRITE(SDRAM_TIMING, tmp);
- DP(printf("SDRAM timing: %08x (%d,%d,%d,%d)\n",
- GTREGREAD(SDRAM_TIMING), tpar,tpar,tpar,tras_clocks));
+ GT_REG_WRITE (SDRAM_TIMING, tmp);
+ DP (printf ("SDRAM timing: %08x (%d,%d,%d,%d)\n",
+ GTREGREAD (SDRAM_TIMING), tpar, tpar, tpar, tras_clocks));
/* SDRAM address decode register */
/* program this with the default value */
- GT_REG_WRITE(SDRAM_ADDRESS_DECODE, 0x2);
- DP(printf("SDRAM decode: %08x\n",
- GTREGREAD(SDRAM_ADDRESS_DECODE)));
+ GT_REG_WRITE (SDRAM_ADDRESS_DECODE, 0x2);
+ DP (printf ("SDRAM decode: %08x\n",
+ GTREGREAD (SDRAM_ADDRESS_DECODE)));
return 0;
}
/* sets up the GT properly with information passed in */
-static int
-setup_sdram(sdram_info_t *info)
+static int setup_sdram (sdram_info_t * info)
{
ulong tmp, check;
ulong *addr = 0;
int i;
/* sanity checking */
- if (! info->banks) return 0;
+ if (!info->banks)
+ return 0;
/* ---------------------------- */
/* Program the GT with the discovered data */
/* bank parameters */
- tmp = (0xf<<16); /* leave all virt bank pages open */
+ tmp = (0xf << 16); /* leave all virt bank pages open */
- DP(printf("drb_size: %d\n", info->drb_size));
+ DP (printf ("drb_size: %d\n", info->drb_size));
switch (info->drb_size) {
case 1:
tmp |= (1 << 14);
tmp |= (3 << 14);
break;
default:
- printf("Error in dram size calculation\n");
+ printf ("Error in dram size calculation\n");
return 1;
}
/* SDRAM bank parameters */
/* the param registers for slot 1 (banks 2+3) are offset by 0x8 */
- GT_REG_WRITE(SDRAM_BANK0PARAMETERS + (info->slot * 0x8), tmp);
- GT_REG_WRITE(SDRAM_BANK1PARAMETERS + (info->slot * 0x8), tmp);
- DP(printf("SDRAM bankparam slot %d (bank %d+%d): %08lx\n", info->slot, info->slot*2, (info->slot*2)+1, tmp));
+ GT_REG_WRITE (SDRAM_BANK0PARAMETERS + (info->slot * 0x8), tmp);
+ GT_REG_WRITE (SDRAM_BANK1PARAMETERS + (info->slot * 0x8), tmp);
+ DP (printf
+ ("SDRAM bankparam slot %d (bank %d+%d): %08lx\n", info->slot,
+ info->slot * 2, (info->slot * 2) + 1, tmp));
/* set the SDRAM configuration for each bank */
for (i = info->slot * 2; i < ((info->slot * 2) + info->banks); i++) {
- DP(printf("*** Running a MRS cycle for bank %d ***\n", i));
+ DP (printf ("*** Running a MRS cycle for bank %d ***\n", i));
/* map the bank */
- memory_map_bank(i, 0, GB/4);
+ memory_map_bank (i, 0, GB / 4);
/* set SDRAM mode */
- GT_REG_WRITE(SDRAM_OPERATION_MODE, 0x3);
- check = GTREGREAD(SDRAM_OPERATION_MODE);
+ GT_REG_WRITE (SDRAM_OPERATION_MODE, 0x3);
+ check = GTREGREAD (SDRAM_OPERATION_MODE);
/* dummy write */
*addr = 0;
/* wait for the command to complete */
- while ((GTREGREAD(SDRAM_OPERATION_MODE) & (1 << 31)) == 0)
- ;
+ while ((GTREGREAD (SDRAM_OPERATION_MODE) & (1 << 31)) == 0);
/* switch back to normal operation mode */
- GT_REG_WRITE(SDRAM_OPERATION_MODE, 0);
- check = GTREGREAD(SDRAM_OPERATION_MODE);
+ GT_REG_WRITE (SDRAM_OPERATION_MODE, 0);
+ check = GTREGREAD (SDRAM_OPERATION_MODE);
/* unmap the bank */
- memory_map_bank(i, 0, 0);
- DP(printf("*** MRS cycle for bank %d done ***\n", i));
+ memory_map_bank (i, 0, 0);
+ DP (printf ("*** MRS cycle for bank %d done ***\n", i));
}
return 0;
* - short between address lines
* - short between data lines
*/
-static long int
-dram_size(long int *base, long int maxsize)
+static long int dram_size (long int *base, long int maxsize)
{
- volatile long int *addr, *b=base;
- long int cnt, val, save1, save2;
+ volatile long int *addr, *b = base;
+ long int cnt, val, save1, save2;
#define STARTVAL (1<<20) /* start test at 1M */
- for (cnt = STARTVAL/sizeof(long); cnt < maxsize/sizeof(long); cnt <<= 1) {
- addr = base + cnt; /* pointer arith! */
-
- save1=*addr; /* save contents of addr */
- save2=*b; /* save contents of base */
-
- *addr=cnt; /* write cnt to addr */
- *b=0; /* put null at base */
-
- /* check at base address */
- if ((*b) != 0) {
- *addr=save1; /* restore *addr */
- *b=save2; /* restore *b */
- return (0);
- }
- val = *addr; /* read *addr */
-
- *addr=save1;
- *b=save2;
-
- if (val != cnt) {
- /* fix boundary condition.. STARTVAL means zero */
- if(cnt==STARTVAL/sizeof(long)) cnt=0;
- return (cnt * sizeof(long));
- }
- }
- return maxsize;
+ for (cnt = STARTVAL / sizeof (long); cnt < maxsize / sizeof (long);
+ cnt <<= 1) {
+ addr = base + cnt; /* pointer arith! */
+
+ save1 = *addr; /* save contents of addr */
+ save2 = *b; /* save contents of base */
+
+ *addr = cnt; /* write cnt to addr */
+ *b = 0; /* put null at base */
+
+ /* check at base address */
+ if ((*b) != 0) {
+ *addr = save1; /* restore *addr */
+ *b = save2; /* restore *b */
+ return (0);
+ }
+ val = *addr; /* read *addr */
+
+ *addr = save1;
+ *b = save2;
+
+ if (val != cnt) {
+ /* fix boundary condition.. STARTVAL means zero */
+ if (cnt == STARTVAL / sizeof (long))
+ cnt = 0;
+ return (cnt * sizeof (long));
+ }
+ }
+ return maxsize;
}
/* ------------------------------------------------------------------------- */
/* U-Boot interface function to SDRAM init - this is where all the
* controlling logic happens */
-long int
-initdram(int board_type)
+long int initdram (int board_type)
{
- ulong checkbank[4] = { [0 ... 3] = 0 };
+ ulong checkbank[4] = {[0 ... 3] = 0 };
int bank_no;
ulong total;
int nhr;
/* first, use the SPD to get info about the SDRAM */
/* check the NHR bit and skip mem init if it's already done */
- nhr = get_hid0() & (1 << 16);
+ nhr = get_hid0 () & (1 << 16);
if (nhr) {
- printf("Skipping SDRAM setup due to NHR bit being set\n");
+ printf ("Skipping SDRAM setup due to NHR bit being set\n");
} else {
/* DIMM0 */
- check_dimm(0, &dimm_info[0]);
+ check_dimm (0, &dimm_info[0]);
/* DIMM1 */
-#ifndef CONFIG_EVB64260_750CX /* EVB64260_750CX has only 1 DIMM */
- check_dimm(1, &dimm_info[1]);
-#else /* CONFIG_EVB64260_750CX */
- memset(&dimm_info[1], 0, sizeof(sdram_info_t));
+#ifndef CONFIG_EVB64260_750CX /* EVB64260_750CX has only 1 DIMM */
+ check_dimm (1, &dimm_info[1]);
+#else /* CONFIG_EVB64260_750CX */
+ memset (&dimm_info[1], 0, sizeof (sdram_info_t));
#endif
/* unmap all banks */
- memory_map_bank(0, 0, 0);
- memory_map_bank(1, 0, 0);
- memory_map_bank(2, 0, 0);
- memory_map_bank(3, 0, 0);
+ memory_map_bank (0, 0, 0);
+ memory_map_bank (1, 0, 0);
+ memory_map_bank (2, 0, 0);
+ memory_map_bank (3, 0, 0);
/* Now, program the GT with the correct values */
- if (setup_sdram_common(dimm_info)) {
- printf("Setup common failed.\n");
+ if (setup_sdram_common (dimm_info)) {
+ printf ("Setup common failed.\n");
}
- if (setup_sdram(&dimm_info[0])) {
- printf("Setup for DIMM1 failed.\n");
+ if (setup_sdram (&dimm_info[0])) {
+ printf ("Setup for DIMM1 failed.\n");
}
- if (setup_sdram(&dimm_info[1])) {
- printf("Setup for DIMM2 failed.\n");
+ if (setup_sdram (&dimm_info[1])) {
+ printf ("Setup for DIMM2 failed.\n");
}
/* set the NHR bit */
- set_hid0(get_hid0() | (1 << 16));
+ set_hid0 (get_hid0 () | (1 << 16));
}
/* next, size the SDRAM banks */
total = 0;
- if (dimm_info[0].banks > 0) checkbank[0] = 1;
- if (dimm_info[0].banks > 1) checkbank[1] = 1;
+ if (dimm_info[0].banks > 0)
+ checkbank[0] = 1;
+ if (dimm_info[0].banks > 1)
+ checkbank[1] = 1;
if (dimm_info[0].banks > 2)
- printf("Error, SPD claims DIMM1 has >2 banks\n");
+ printf ("Error, SPD claims DIMM1 has >2 banks\n");
- if (dimm_info[1].banks > 0) checkbank[2] = 1;
- if (dimm_info[1].banks > 1) checkbank[3] = 1;
+ if (dimm_info[1].banks > 0)
+ checkbank[2] = 1;
+ if (dimm_info[1].banks > 1)
+ checkbank[3] = 1;
if (dimm_info[1].banks > 2)
- printf("Error, SPD claims DIMM2 has >2 banks\n");
+ printf ("Error, SPD claims DIMM2 has >2 banks\n");
/* Generic dram sizer: works even if we don't have i2c DIMMs,
* as long as the timing settings are more or less correct */
/*
* pass 1: size all the banks, using first bat (0-256M)
- * limitation: we only support 256M per bank due to
- * us only having 1 BAT for all DRAM
+ * limitation: we only support 256M per bank due to
+ * us only having 1 BAT for all DRAM
*/
for (bank_no = 0; bank_no < CFG_DRAM_BANKS; bank_no++) {
/* skip over banks that are not populated */
- if (! checkbank[bank_no])
+ if (!checkbank[bank_no])
continue;
- DP(printf("checking bank %d\n", bank_no));
+ DP (printf ("checking bank %d\n", bank_no));
- memory_map_bank(bank_no, 0, GB/4);
- checkbank[bank_no] = dram_size(NULL, GB/4);
- memory_map_bank(bank_no, 0, 0);
+ memory_map_bank (bank_no, 0, GB / 4);
+ checkbank[bank_no] = dram_size (NULL, GB / 4);
+ memory_map_bank (bank_no, 0, 0);
- DP(printf("bank %d %08lx\n", bank_no, checkbank[bank_no]));
+ DP (printf ("bank %d %08lx\n", bank_no, checkbank[bank_no]));
}
/*
* pass 2: contiguously map each bank into physical address
- * space.
+ * space.
*/
- dimm_info[0].banks=dimm_info[1].banks=0;
+ dimm_info[0].banks = dimm_info[1].banks = 0;
for (bank_no = 0; bank_no < CFG_DRAM_BANKS; bank_no++) {
- if(!checkbank[bank_no]) continue;
+ if (!checkbank[bank_no])
+ continue;
- dimm_info[bank_no/2].banks++;
- dimm_info[bank_no/2].size+=checkbank[bank_no];
+ dimm_info[bank_no / 2].banks++;
+ dimm_info[bank_no / 2].size += checkbank[bank_no];
- memory_map_bank(bank_no, total, checkbank[bank_no]);
+ memory_map_bank (bank_no, total, checkbank[bank_no]);
#ifdef MAP_PCI
- memory_map_bank_pci(bank_no, total, checkbank[bank_no]);
+ memory_map_bank_pci (bank_no, total, checkbank[bank_no]);
#endif
total += checkbank[bank_no];
}
* in that configuration, ECC chips are mounted, even for stacked
* chips)
*/
- if (checkbank[2]==0 && checkbank[3]==0) {
- dimm_info[0].ecc=2;
- GT_REG_WRITE(SDRAM_TIMING, GTREGREAD(SDRAM_TIMING) | (1 << 13));
+ if (checkbank[2] == 0 && checkbank[3] == 0) {
+ dimm_info[0].ecc = 2;
+ GT_REG_WRITE (SDRAM_TIMING,
+ GTREGREAD (SDRAM_TIMING) | (1 << 13));
/* TODO: do we have to run MRS cycles again? */
}
#endif /* CONFIG_ZUMA_V2 */
- if (GTREGREAD(SDRAM_TIMING) & (1 << 13)) {
- puts("[ECC] ");
+ if (GTREGREAD (SDRAM_TIMING) & (1 << 13)) {
+ puts ("[ECC] ");
}
#endif /* CONFIG_ECC */
#ifdef DEBUG
- dump_dimm_info(&dimm_info[0]);
- dump_dimm_info(&dimm_info[1]);
+ dump_dimm_info (&dimm_info[0]);
+ dump_dimm_info (&dimm_info[1]);
#endif
/* TODO: return at MOST 256M? */
/* return total > GB/4 ? GB/4 : total; */
projects / karo-tx-uboot.git / blobdiff