#include <linux/compiler.h>
#include <asm/mmu.h>
#include <asm/processor.h>
+#include <asm/errno.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
#define CLK_MUX_SEL_MASK 0x4
#define ETH_PHY_CLK_OUT 0x4
-#define PLL_NUM 2
DECLARE_GLOBAL_DATA_PTR;
debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl);
switch (serdes1_prtcl) {
+ case 0x29:
case 0x2a:
case 0x2C:
case 0x2D:
break;
#ifdef CONFIG_PPC_B4420
+ case 0x17:
case 0x18:
/*
* Configuration:
(void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
u32 serdes1_prtcl, lane;
unsigned int flag_sgmii_aurora_prtcl = 0;
- int ret, i;
+ int i;
+ int ret = 0;
serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl);
- /* Clear SRDS_RSTCTL_RST bit for both PLLs before changing refclks
+ /* To prevent generation of reset request from SerDes
+ * while changing the refclks, By setting SRDS_RST_MSK bit,
+ * SerDes reset event cannot cause a reset request
*/
- for (i = 0; i < PLL_NUM; i++)
- clrbits_be32(&srds_regs->bank[i].rstctl, SRDS_RSTCTL_RST);
+ setbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK);
+
/* Reconfigure IDT idt8t49n222a device for CPRI to work
* For this SerDes1's Refclk1 and refclk2 need to be set
* to 122.88MHz
SERDES_REFCLK_122_88, 0);
if (ret) {
printf("IDT8T49N222A configuration failed.\n");
- return ret;
+ goto out;
} else
- printf("IDT8T49N222A configured.\n");
+ debug("IDT8T49N222A configured.\n");
} else {
- return ret;
+ goto out;
}
select_i2c_ch_pca(I2C_CH_DEFAULT);
/* Steps For SerDes PLLs reset and reconfiguration after
* changing SerDes's refclks
*/
- for (i = 0; i < PLL_NUM; i++) {
+ for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) {
debug("For PLL%d reset and reconfiguration after"
" changing refclks\n", i+1);
clrbits_be32(&srds_regs->bank[i].rstctl,
printf("WARNING:IDT8T49N222A configuration not"
" supported for:%x SerDes1 Protocol.\n",
serdes1_prtcl);
- return -1;
}
- return 0;
+out:
+ /* Clearing SRDS_RST_MSK bit as now
+ * SerDes reset event can cause a reset request
+ */
+ clrbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK);
+ return ret;
+}
+
+int config_serdes2_refclks(void)
+{
+ ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ serdes_corenet_t *srds2_regs =
+ (void *)CONFIG_SYS_FSL_CORENET_SERDES2_ADDR;
+ u32 serdes2_prtcl;
+ int ret = 0;
+ int i;
+
+ serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+ if (!serdes2_prtcl) {
+ debug("SERDES2 is not enabled\n");
+ return -ENODEV;
+ }
+ serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+ debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl);
+
+ /* To prevent generation of reset request from SerDes
+ * while changing the refclks, By setting SRDS_RST_MSK bit,
+ * SerDes reset event cannot cause a reset request
+ */
+ setbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK);
+
+ /* Reconfigure IDT idt8t49n222a device for PCIe SATA to work
+ * For this SerDes2's Refclk1 need to be set to 100MHz
+ */
+ switch (serdes2_prtcl) {
+ case 0x9E:
+ case 0x9A:
+ case 0xb2:
+ debug("Configuring IDT for PCIe SATA for srds_prctl:%x\n",
+ serdes2_prtcl);
+ ret = select_i2c_ch_pca(I2C_CH_IDT);
+ if (!ret) {
+ ret = set_serdes_refclk(IDT_SERDES2_ADDRESS, 2,
+ SERDES_REFCLK_100,
+ SERDES_REFCLK_156_25, 0);
+ if (ret) {
+ printf("IDT8T49N222A configuration failed.\n");
+ goto out;
+ } else
+ debug("IDT8T49N222A configured.\n");
+ } else {
+ goto out;
+ }
+ select_i2c_ch_pca(I2C_CH_DEFAULT);
+
+ /* Steps For SerDes PLLs reset and reconfiguration after
+ * changing SerDes's refclks
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) {
+ clrbits_be32(&srds2_regs->bank[i].rstctl,
+ SRDS_RSTCTL_SDRST_B);
+ udelay(10);
+ clrbits_be32(&srds2_regs->bank[i].rstctl,
+ (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B));
+ udelay(10);
+ setbits_be32(&srds2_regs->bank[i].rstctl,
+ SRDS_RSTCTL_RST);
+ setbits_be32(&srds2_regs->bank[i].rstctl,
+ (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B
+ | SRDS_RSTCTL_SDRST_B));
+ }
+ break;
+ default:
+ printf("IDT configuration not supported for:%x S2 Protocol.\n",
+ serdes2_prtcl);
+ }
+
+out:
+ /* Clearing SRDS_RST_MSK bit as now
+ * SerDes reset event can cause a reset request
+ */
+ clrbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK);
+ return ret;
}
int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+ int ret;
/*
* Remap Boot flash + PROMJET region to caching-inhibited
else
printf("SerDes1 Refclks have been set.\n");
+ /* SerDes2 refclks need to be set again, as default clks
+ * are not suitable for PCIe SATA to work
+ * This function will set SerDes2's Refclk1 and refclk2
+ * for SerDes2 protocols having PCIe in them
+ * for PCIe SATA to work
+ */
+ ret = config_serdes2_refclks();
+ if (!ret)
+ printf("SerDes2 Refclks have been set.\n");
+ else if (ret == -ENODEV)
+ printf("SerDes disable, Refclks couldn't change.\n");
+ else
+ printf("SerDes2 Refclk reconfiguring failed.\n");
+
/* Configure VSC3316 and VSC3308 crossbar switches */
if (configure_vsc3316_3308())
printf("VSC:failed to configure VSC3316/3308.\n");
projects / karo-tx-uboot.git / blobdiff