/*
- * Copyright 2009 Freescale Semiconductor.
+ * Copyright 2009-2010 Freescale Semiconductor.
*
* (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
*
*/
#include <common.h>
+#include <hwconfig.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/mmu.h>
+#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
#include <asm/fsl_ddr_sdram.h>
#include <ioports.h>
#include <libfdt.h>
#include <fdt_support.h>
+#include <fsl_esdhc.h>
#include "bcsr.h"
+#if defined(CONFIG_PQ_MDS_PIB)
+#include "../common/pq-mds-pib.h"
+#endif
phys_size_t fixed_sdram(void);
{5, 10, 2, 0, 3}, /* UART1_CTS_B */
{5, 11, 1, 0, 2}, /* UART1_RTS_B */
+ /* QE UART */
+ {0, 19, 1, 0, 2}, /* QEUART_TX */
+ {1, 17, 2, 0, 3}, /* QEUART_RX */
+ {0, 25, 1, 0, 1}, /* QEUART_RTS */
+ {1, 23, 2, 0, 1}, /* QEUART_CTS */
+
+ /* QE USB */
+ {5, 3, 1, 0, 1}, /* USB_OE */
+ {5, 4, 1, 0, 2}, /* USB_TP */
+ {5, 5, 1, 0, 2}, /* USB_TN */
+ {5, 6, 2, 0, 2}, /* USB_RP */
+ {5, 7, 2, 0, 1}, /* USB_RX */
+ {5, 8, 2, 0, 1}, /* USB_RN */
+ {2, 4, 2, 0, 2}, /* CLK5 */
+
+ /* SPI Flash, M25P40 */
+ {4, 27, 3, 0, 1}, /* SPI_MOSI */
+ {4, 28, 3, 0, 1}, /* SPI_MISO */
+ {4, 29, 3, 0, 1}, /* SPI_CLK */
+ {4, 30, 1, 0, 0}, /* SPI_SEL, GPIO */
+
{0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */
};
return 0;
}
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_NAND_BASE;
+ const u8 flash_esel = 0;
+
+ /*
+ * Remap Boot flash to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_NAND_BASE, /* tlb, epn, rpn */
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */
+ 0, flash_esel, /* ts, esel */
+ BOOKE_PAGESZ_64M, 1); /* tsize, iprot */
+
+ return 0;
+}
+
int checkboard (void)
{
printf ("Board: 8569 MDS\n");
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
out_be32(&lbc->lcrr, (u32)in_be32(&lbc->lcrr)| 0x00030000);
}
-#ifdef CONFIG_PCIE1
-static struct pci_controller pcie1_hose;
-#endif /* CONFIG_PCIE1 */
+static void fdt_board_disable_serial(void *blob, bd_t *bd, const char *alias)
+{
+ const char *status = "disabled";
+ int off;
+ int err;
+
+ off = fdt_path_offset(blob, alias);
+ if (off < 0) {
+ printf("WARNING: could not find %s alias: %s.\n", alias,
+ fdt_strerror(off));
+ return;
+ }
-int first_free_busno = 0;
+ err = fdt_setprop(blob, off, "status", status, strlen(status) + 1);
+ if (err) {
+ printf("WARNING: could not set status for serial0: %s.\n",
+ fdt_strerror(err));
+ return;
+ }
+}
-#ifdef CONFIG_PCI
-void
-pci_init_board(void)
+/*
+ * Because of an erratum in prototype boards it is impossible to use eSDHC
+ * without disabling UART0 (which makes it quite easy to 'brick' the board
+ * by simply issung 'setenv hwconfig esdhc', and not able to interact with
+ * U-Boot anylonger).
+ *
+ * So, but default we assume that the board is a prototype, which is a most
+ * safe assumption. There is no way to determine board revision from a
+ * register, so we use hwconfig.
+ */
+
+static int prototype_board(void)
{
- volatile ccsr_gur_t *gur;
- uint io_sel;
- uint host_agent;
+ if (hwconfig_subarg("board", "rev", NULL))
+ return hwconfig_subarg_cmp("board", "rev", "prototype");
+ return 1;
+}
- gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
- host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
+static int esdhc_disables_uart0(void)
+{
+ return prototype_board() ||
+ hwconfig_subarg_cmp("esdhc", "mode", "4-bits");
+}
-#ifdef CONFIG_PCIE1
+static void fdt_board_fixup_qe_uart(void *blob, bd_t *bd)
{
- volatile ccsr_fsl_pci_t *pci;
- struct pci_controller *hose;
- int pcie_ep;
- struct pci_region *r;
- int pcie_configured;
-
- pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
- hose = &pcie1_hose;
- pcie_ep = is_fsl_pci_agent(LAW_TRGT_IF_PCIE_1, host_agent);
- r = hose->regions;
- pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel);
+ u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
+ const char *devtype = "serial";
+ const char *compat = "ucc_uart";
+ const char *clk = "brg9";
+ u32 portnum = 0;
+ int off = -1;
+
+ if (!hwconfig("qe_uart"))
+ return;
+
+ if (hwconfig("esdhc") && esdhc_disables_uart0()) {
+ printf("QE UART: won't enable with esdhc.\n");
+ return;
+ }
+
+ fdt_board_disable_serial(blob, bd, "serial1");
- if (pcie_configured && !(gur->devdisr & MPC85xx_DEVDISR_PCIE)){
- printf ("\n PCIE connected to slot as %s (base address %x)",
- pcie_ep ? "End Point" : "Root Complex",
- (uint)pci);
+ while (1) {
+ const u32 *idx;
+ int len;
- if (pci->pme_msg_det) {
- pci->pme_msg_det = 0xffffffff;
- debug (" with errors. Clearing. Now 0x%08x",
- pci->pme_msg_det);
+ off = fdt_node_offset_by_compatible(blob, off, "ucc_geth");
+ if (off < 0) {
+ printf("WARNING: unable to fixup device tree for "
+ "QE UART\n");
+ return;
}
- printf ("\n");
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCIE1_MEM_BUS,
- CONFIG_SYS_PCIE1_MEM_PHYS,
- CONFIG_SYS_PCIE1_MEM_SIZE,
- PCI_REGION_MEM);
+ idx = fdt_getprop(blob, off, "cell-index", &len);
+ if (!idx || len != sizeof(*idx) || *idx != fdt32_to_cpu(2))
+ continue;
+ break;
+ }
+
+ fdt_setprop(blob, off, "device_type", devtype, strlen(devtype) + 1);
+ fdt_setprop(blob, off, "compatible", compat, strlen(compat) + 1);
+ fdt_setprop(blob, off, "tx-clock-name", clk, strlen(clk) + 1);
+ fdt_setprop(blob, off, "rx-clock-name", clk, strlen(clk) + 1);
+ fdt_setprop(blob, off, "port-number", &portnum, sizeof(portnum));
+
+ setbits_8(&bcsr[15], BCSR15_QEUART_EN);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+
+int board_mmc_init(bd_t *bd)
+{
+ struct ccsr_gur *gur = (struct ccsr_gur *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+ u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
+ u8 bcsr6 = BCSR6_SD_CARD_1BIT;
+
+ if (!hwconfig("esdhc"))
+ return 0;
+
+ printf("Enabling eSDHC...\n"
+ " For eSDHC to function, I2C2 ");
+ if (esdhc_disables_uart0()) {
+ printf("and UART0 should be disabled.\n");
+ printf(" Redirecting stderr, stdout and stdin to UART1...\n");
+ console_assign(stderr, "eserial1");
+ console_assign(stdout, "eserial1");
+ console_assign(stdin, "eserial1");
+ printf("Switched to UART1 (initial log has been printed to "
+ "UART0).\n");
+
+ clrsetbits_be32(&gur->plppar1, PLPPAR1_UART0_BIT_MASK,
+ PLPPAR1_ESDHC_4BITS_VAL);
+ clrsetbits_be32(&gur->plpdir1, PLPDIR1_UART0_BIT_MASK,
+ PLPDIR1_ESDHC_4BITS_VAL);
+ bcsr6 |= BCSR6_SD_CARD_4BITS;
+ } else {
+ printf("should be disabled.\n");
+ }
+
+ /* Assign I2C2 signals to eSDHC. */
+ clrsetbits_be32(&gur->plppar1, PLPPAR1_I2C_BIT_MASK,
+ PLPPAR1_ESDHC_VAL);
+ clrsetbits_be32(&gur->plpdir1, PLPDIR1_I2C_BIT_MASK,
+ PLPDIR1_ESDHC_VAL);
- /* outbound io */
- pci_set_region(r++,
- CONFIG_SYS_PCIE1_IO_BUS,
- CONFIG_SYS_PCIE1_IO_PHYS,
- CONFIG_SYS_PCIE1_IO_SIZE,
- PCI_REGION_IO);
+ /* Mux I2C2 (and optionally UART0) signals to eSDHC. */
+ setbits_8(&bcsr[6], bcsr6);
- hose->region_count = r - hose->regions;
+ return fsl_esdhc_mmc_init(bd);
+}
+
+static void fdt_board_fixup_esdhc(void *blob, bd_t *bd)
+{
+ const char *status = "disabled";
+ int off = -1;
- hose->first_busno=first_free_busno;
+ if (!hwconfig("esdhc"))
+ return;
- fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
- printf ("PCIE on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
+ if (esdhc_disables_uart0())
+ fdt_board_disable_serial(blob, bd, "serial0");
+
+ while (1) {
+ const u32 *idx;
+ int len;
+
+ off = fdt_node_offset_by_compatible(blob, off, "fsl-i2c");
+ if (off < 0)
+ break;
+
+ idx = fdt_getprop(blob, off, "cell-index", &len);
+ if (!idx || len != sizeof(*idx))
+ continue;
+
+ if (*idx == 1) {
+ fdt_setprop(blob, off, "status", status,
+ strlen(status) + 1);
+ break;
+ }
+ }
- first_free_busno=hose->last_busno+1;
+ if (hwconfig_subarg_cmp("esdhc", "mode", "4-bits")) {
+ off = fdt_node_offset_by_compatible(blob, -1, "fsl,esdhc");
+ if (off < 0) {
+ printf("WARNING: could not find esdhc node\n");
+ return;
+ }
+ fdt_delprop(blob, off, "sdhci,1-bit-only");
+ }
+}
+#else
+static inline void fdt_board_fixup_esdhc(void *blob, bd_t *bd) {}
+#endif
+static void fdt_board_fixup_qe_usb(void *blob, bd_t *bd)
+{
+ u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
+
+ if (hwconfig_subarg_cmp("qe_usb", "speed", "low"))
+ clrbits_8(&bcsr[17], BCSR17_nUSBLOWSPD);
+ else
+ setbits_8(&bcsr[17], BCSR17_nUSBLOWSPD);
+
+ if (hwconfig_subarg_cmp("qe_usb", "mode", "peripheral")) {
+ clrbits_8(&bcsr[17], BCSR17_USBVCC);
+ clrbits_8(&bcsr[17], BCSR17_USBMODE);
+ do_fixup_by_compat(blob, "fsl,mpc8569-qe-usb", "mode",
+ "peripheral", sizeof("peripheral"), 1);
} else {
- printf (" PCIE: disabled\n");
+ setbits_8(&bcsr[17], BCSR17_USBVCC);
+ setbits_8(&bcsr[17], BCSR17_USBMODE);
}
+
+ clrbits_8(&bcsr[17], BCSR17_nUSBEN);
}
+
+#ifdef CONFIG_PCIE1
+static struct pci_controller pcie1_hose;
+#endif /* CONFIG_PCIE1 */
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ struct fsl_pci_info pci_info[1];
+ u32 devdisr, pordevsr, io_sel;
+ int first_free_busno = 0;
+ int num = 0;
+
+ int pcie_ep, pcie_configured;
+
+ devdisr = in_be32(&gur->devdisr);
+ pordevsr = in_be32(&gur->pordevsr);
+ io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
+
+ debug (" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel);
+
+#if defined(CONFIG_PQ_MDS_PIB)
+ pib_init();
+#endif
+
+#ifdef CONFIG_PCIE1
+ pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel);
+
+ if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
+ SET_STD_PCIE_INFO(pci_info[num], 1);
+ pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs);
+ printf("PCIE1: connected to Slot as %s (base addr %lx)\n",
+ pcie_ep ? "Endpoint" : "Root Complex",
+ pci_info[num].regs);
+ first_free_busno = fsl_pci_init_port(&pci_info[num++],
+ &pcie1_hose, first_free_busno);
+ } else {
+ printf("PCIE1: disabled\n");
+ }
+
+ puts("\n");
#else
- gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
+ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE); /* disable */
#endif
+
}
#endif /* CONFIG_PCI */
break;
}
- err = fdt_setprop_string(blob, nodeoff, "phy-connection-type",
- "rmii");
+ err = fdt_fixup_phy_connection(blob, nodeoff, RMII);
+
if (err < 0) {
printf("WARNING: could not set phy-connection-type "
"%s.\n", fdt_strerror(err));
#endif
ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCIE1
- ft_fsl_pci_setup(blob, "pci1", &pcie1_hose);
-#endif
+ FT_FSL_PCI_SETUP;
+
+ fdt_board_fixup_esdhc(blob, bd);
+ fdt_board_fixup_qe_uart(blob, bd);
+ fdt_board_fixup_qe_usb(blob, bd);
}
#endif
projects / karo-tx-uboot.git / blobdiff