--- /dev/null
+/*
+ * (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
+ * (C) Copyright 2009 Dave Srl www.dave.eu
+ * (C) Copyright 2010 ifm ecomatic GmbH
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/bitops.h>
+#include <command.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <asm/mpc512x.h>
+#include <fdt_support.h>
+#ifdef CONFIG_MISC_INIT_R
+#include <i2c.h>
+#endif
+
+static int eeprom_diag;
+static int mac_diag;
+static int gpio_diag;
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void gpio_configure(void)
+{
+ immap_t *im;
+ gpio512x_t *gpioregs;
+
+ im = (immap_t *) CONFIG_SYS_IMMR;
+ gpioregs = &im->gpio;
+ out_be32(&gpioregs->gpodr, 0x00290000); /* open drain */
+ out_be32(&gpioregs->gpdat, 0x80001040); /* data (when output) */
+
+ /*
+ * out_be32(&gpioregs->gpdir, 0xC2293020);
+ * workaround for a hardware effect: configure direction in pieces,
+ * setting all outputs at once drops the reset line too low and
+ * makes us lose the MII connection (breaks ethernet for us)
+ */
+ out_be32(&gpioregs->gpdir, 0x02003060); /* direction */
+ setbits_be32(&gpioregs->gpdir, 0x00200000); /* += reset asi */
+ udelay(10);
+ setbits_be32(&gpioregs->gpdir, 0x00080000); /* += reset safety */
+ udelay(10);
+ setbits_be32(&gpioregs->gpdir, 0x00010000); /* += reset comm */
+ udelay(10);
+ setbits_be32(&gpioregs->gpdir, 0xC0000000); /* += backlight, KB sel */
+
+ /* to turn from red to yellow when U-Boot runs */
+ setbits_be32(&gpioregs->gpdat, 0x00002020);
+ out_be32(&gpioregs->gpimr, 0x00000000); /* interrupt mask */
+ out_be32(&gpioregs->gpicr1, 0x00000004); /* interrupt sense part 1 */
+ out_be32(&gpioregs->gpicr2, 0x00A80000); /* interrupt sense part 2 */
+ out_be32(&gpioregs->gpier, 0xFFFFFFFF); /* interrupt events, clear */
+}
+
+/* the physical location of the pins */
+#define GPIOKEY_ROW_BITMASK 0x40000000
+#define GPIOKEY_ROW_UPPER 0
+#define GPIOKEY_ROW_LOWER 1
+
+#define GPIOKEY_COL0_BITMASK 0x20000000
+#define GPIOKEY_COL1_BITMASK 0x10000000
+#define GPIOKEY_COL2_BITMASK 0x08000000
+
+/* the logical presentation of pressed keys */
+#define GPIOKEY_BIT_FNLEFT (1 << 5)
+#define GPIOKEY_BIT_FNRIGHT (1 << 4)
+#define GPIOKEY_BIT_DIRUP (1 << 3)
+#define GPIOKEY_BIT_DIRLEFT (1 << 2)
+#define GPIOKEY_BIT_DIRRIGHT (1 << 1)
+#define GPIOKEY_BIT_DIRDOWN (1 << 0)
+
+/* the hotkey combination which starts recovery */
+#define GPIOKEY_BITS_RECOVERY (GPIOKEY_BIT_FNLEFT | GPIOKEY_BIT_DIRUP | \
+ GPIOKEY_BIT_DIRDOWN)
+
+static void gpio_selectrow(gpio512x_t *gpioregs, u32 row)
+{
+
+ if (row)
+ setbits_be32(&gpioregs->gpdat, GPIOKEY_ROW_BITMASK);
+ else
+ clrbits_be32(&gpioregs->gpdat, GPIOKEY_ROW_BITMASK);
+ udelay(10);
+}
+
+static u32 gpio_querykbd(void)
+{
+ immap_t *im;
+ gpio512x_t *gpioregs;
+ u32 keybits;
+ u32 input;
+
+ im = (immap_t *)CONFIG_SYS_IMMR;
+ gpioregs = &im->gpio;
+ keybits = 0;
+
+ /* query upper row */
+ gpio_selectrow(gpioregs, GPIOKEY_ROW_UPPER);
+ input = in_be32(&gpioregs->gpdat);
+ if ((input & GPIOKEY_COL0_BITMASK) == 0)
+ keybits |= GPIOKEY_BIT_FNLEFT;
+ if ((input & GPIOKEY_COL1_BITMASK) == 0)
+ keybits |= GPIOKEY_BIT_DIRUP;
+ if ((input & GPIOKEY_COL2_BITMASK) == 0)
+ keybits |= GPIOKEY_BIT_FNRIGHT;
+
+ /* query lower row */
+ gpio_selectrow(gpioregs, GPIOKEY_ROW_LOWER);
+ input = in_be32(&gpioregs->gpdat);
+ if ((input & GPIOKEY_COL0_BITMASK) == 0)
+ keybits |= GPIOKEY_BIT_DIRLEFT;
+ if ((input & GPIOKEY_COL1_BITMASK) == 0)
+ keybits |= GPIOKEY_BIT_DIRRIGHT;
+ if ((input & GPIOKEY_COL2_BITMASK) == 0)
+ keybits |= GPIOKEY_BIT_DIRDOWN;
+
+ /* return bit pattern for keys */
+ return keybits;
+}
+
+/* excerpt from the recovery's hw_info.h */
+
+struct __attribute__ ((__packed__)) eeprom_layout {
+ char magic[3]; /** 'ifm' */
+ u8 len[2]; /** content length without magic/len fields */
+ u8 version[3]; /** structure version */
+ u8 type; /** type of PCB */
+ u8 reserved[0x37]; /** padding up to offset 0x40 */
+ u8 macaddress[6]; /** ethernet MAC (for the mainboard) @0x40 */
+};
+
+#define HW_COMP_MAINCPU 2
+
+static struct eeprom_layout eeprom_content;
+static int eeprom_was_read; /* has_been_read */
+static int eeprom_is_valid;
+static int eeprom_version;
+
+#define get_eeprom_field_int(name) ({ \
+ int value; \
+ int idx; \
+ value = 0; \
+ for (idx = 0; idx < sizeof(name); idx++) { \
+ value <<= 8; \
+ value |= name[idx]; \
+ } \
+ value; \
+})
+
+static int read_eeprom(void)
+{
+ int eeprom_datalen;
+ int ret;
+
+ if (eeprom_was_read)
+ return 0;
+
+ eeprom_is_valid = 0;
+ ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
+ (uchar *)&eeprom_content, sizeof(eeprom_content));
+ if (eeprom_diag) {
+ printf("DIAG: %s() read rc[%d], size[%d]\n",
+ __func__, ret, sizeof(eeprom_content));
+ }
+
+ if (ret != 0)
+ return -1;
+
+ eeprom_was_read = 1;
+
+ /*
+ * check validity of EEPROM content
+ * (check version, length, optionally checksum)
+ */
+ eeprom_is_valid = 1;
+ eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
+ eeprom_version = get_eeprom_field_int(eeprom_content.version);
+
+ if (eeprom_diag) {
+ printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
+ __func__, eeprom_content.magic[0],
+ eeprom_content.magic[1], eeprom_content.magic[2],
+ eeprom_datalen, eeprom_version, eeprom_content.type);
+ }
+ if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
+ eeprom_is_valid = 0;
+ if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
+ eeprom_is_valid = 0;
+ if ((eeprom_version != 1) && (eeprom_version != 2))
+ eeprom_is_valid = 0;
+ if (eeprom_content.type != HW_COMP_MAINCPU)
+ eeprom_is_valid = 0;
+
+ if (eeprom_diag)
+ printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);
+
+ return ret;
+}
+
+int mac_read_from_eeprom(void)
+{
+ const u8 *mac;
+ const char *mac_txt;
+
+ if (read_eeprom()) {
+ printf("I2C EEPROM read failed.\n");
+ return -1;
+ }
+
+ if (!eeprom_is_valid) {
+ printf("I2C EEPROM content not valid\n");
+ return -1;
+ }
+
+ mac = NULL;
+ switch (eeprom_version) {
+ case 1:
+ case 2:
+ mac = (const u8 *)&eeprom_content.macaddress;
+ break;
+ }
+
+ if (mac && is_valid_ether_addr(mac)) {
+ eth_setenv_enetaddr("ethaddr", mac);
+ if (mac_diag) {
+ mac_txt = getenv("ethaddr");
+ if (mac_txt)
+ printf("DIAG: MAC value [%s]\n", mac_txt);
+ else
+ printf("DIAG: failed to setup MAC env\n");
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * BEWARE!
+ * this board uses DDR1(!) Micron SDRAM, *NOT* the DDR2
+ * which the ADS, Aria or PDM360NG boards are using
+ * (the steps outlined here refer to the Micron datasheet)
+ */
+u32 sdram_init_seq[] = {
+ /* item 6, at least one NOP after CKE went high */
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ /* item 7, precharge all; item 8, tRP (20ns) */
+ CONFIG_SYS_DDRCMD_PCHG_ALL,
+ CONFIG_SYS_DDRCMD_NOP,
+ /* item 9, extended mode register; item 10, tMRD 10ns) */
+ CONFIG_SYS_MICRON_EMODE | CONFIG_SYS_MICRON_EMODE_PARAM,
+ CONFIG_SYS_DDRCMD_NOP,
+ /*
+ * item 11, (base) mode register _with_ reset DLL;
+ * item 12, tMRD (10ns)
+ */
+ CONFIG_SYS_MICRON_BMODE | CONFIG_SYS_MICRON_BMODE_RSTDLL |
+ CONFIG_SYS_MICRON_BMODE_PARAM,
+ CONFIG_SYS_DDRCMD_NOP,
+ /* item 13, precharge all; item 14, tRP (20ns) */
+ CONFIG_SYS_DDRCMD_PCHG_ALL,
+ CONFIG_SYS_DDRCMD_NOP,
+ /*
+ * item 15, auto refresh (i.e. refresh with CKE held high);
+ * item 16, tRFC (70ns)
+ */
+ CONFIG_SYS_DDRCMD_RFSH,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ /*
+ * item 17, auto refresh (i.e. refresh with CKE held high);
+ * item 18, tRFC (70ns)
+ */
+ CONFIG_SYS_DDRCMD_RFSH,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ CONFIG_SYS_DDRCMD_NOP,
+ /* item 19, optional, unassert DLL reset; item 20, tMRD (20ns) */
+ CONFIG_SYS_MICRON_BMODE | CONFIG_SYS_MICRON_BMODE_PARAM,
+ CONFIG_SYS_DDRCMD_NOP,
+ /*
+ * item 21, "actually done", but make sure 200 DRAM clock cycles
+ * have passed after DLL reset before READ requests are issued
+ * (200 cycles at 160MHz -> 1.25 usec)
+ */
+ /* EMPTY, optional, we don't do it */
+};
+
+phys_size_t initdram(int board_type)
+{
+ return fixed_sdram(NULL, sdram_init_seq, ARRAY_SIZE(sdram_init_seq));
+}
+
+int misc_init_r(void)
+{
+ u32 keys;
+ char *s;
+ int want_recovery;
+
+ /* we use bus I2C-0 for the on-board eeprom */
+ i2c_set_bus_num(0);
+
+ /* setup GPIO directions and initial values */
+ gpio_configure();
+
+ /*
+ * enforce the start of the recovery system when
+ * - the appropriate keys were pressed
+ * - "some" external software told us to
+ * - a previous installation was aborted or has failed
+ */
+ want_recovery = 0;
+ keys = gpio_querykbd();
+ if (gpio_diag)
+ printf("GPIO keyboard status [0x%02X]\n", keys);
+ if ((keys & GPIOKEY_BITS_RECOVERY) == GPIOKEY_BITS_RECOVERY) {
+ printf("detected recovery request (keyboard)\n");
+ want_recovery = 1;
+ }
+ s = getenv("want_recovery");
+ if ((s != NULL) && (*s != '\0')) {
+ printf("detected recovery request (environment)\n");
+ want_recovery = 1;
+ }
+ s = getenv("install_in_progress");
+ if ((s != NULL) && (*s != '\0')) {
+ printf("previous installation has not completed\n");
+ want_recovery = 1;
+ }
+ s = getenv("install_failed");
+ if ((s != NULL) && (*s != '\0')) {
+ printf("previous installation has failed\n");
+ want_recovery = 1;
+ }
+ if (want_recovery) {
+ printf("enforced start of the recovery system\n");
+ setenv("bootcmd", "run recovery");
+ }
+
+ /*
+ * boot the recovery system without waiting; boot the
+ * production system without waiting by default, only
+ * insert a pause (to provide a chance to get a prompt)
+ * when GPIO keys were pressed during power on
+ */
+ if (want_recovery)
+ setenv("bootdelay", "0");
+ else if (!keys)
+ setenv("bootdelay", "0");
+ else
+ setenv("bootdelay", "2");
+
+ /* get the ethernet MAC from I2C EEPROM */
+ mac_read_from_eeprom();
+
+ return 0;
+}
+
+/* setup specific IO pad configuration */
+static iopin_t ioregs_init[] = {
+ { /* LPC CS3 */
+ offsetof(struct ioctrl512x, io_control_nfc_ce0), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(1) | IO_PIN_DS(2),
+ },
+ { /* LPC CS1 */
+ offsetof(struct ioctrl512x, io_control_lpc_cs1), 1,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+ { /* LPC CS2 */
+ offsetof(struct ioctrl512x, io_control_lpc_cs2), 1,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+ { /* LPC CS4, CS5 */
+ offsetof(struct ioctrl512x, io_control_pata_ce1), 2,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(1) | IO_PIN_DS(2),
+ },
+ { /* SDHC CLK, CMD, D0, D1, D2, D3 */
+ offsetof(struct ioctrl512x, io_control_pata_ior), 6,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(1) | IO_PIN_DS(2),
+ },
+ { /* GPIO keyboard */
+ offsetof(struct ioctrl512x, io_control_pci_ad30), 4,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO DN1 PF, LCD power, DN2 PF */
+ offsetof(struct ioctrl512x, io_control_pci_ad26), 3,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO reset AS-i */
+ offsetof(struct ioctrl512x, io_control_pci_ad21), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO reset safety */
+ offsetof(struct ioctrl512x, io_control_pci_ad19), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO reset netX */
+ offsetof(struct ioctrl512x, io_control_pci_ad16), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO ma2 en */
+ offsetof(struct ioctrl512x, io_control_pci_ad15), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO SD CD, SD WP */
+ offsetof(struct ioctrl512x, io_control_pci_ad08), 2,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* FEC RX DV */
+ offsetof(struct ioctrl512x, io_control_pci_ad06), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(2) | IO_PIN_DS(2),
+ },
+ { /* GPIO AS-i prog, AS-i done, LCD backlight */
+ offsetof(struct ioctrl512x, io_control_pci_ad05), 3,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO AS-i wdg */
+ offsetof(struct ioctrl512x, io_control_pci_req2), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO safety wdg */
+ offsetof(struct ioctrl512x, io_control_pci_req1), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO netX wdg */
+ offsetof(struct ioctrl512x, io_control_pci_req0), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO IRQ powerfail */
+ offsetof(struct ioctrl512x, io_control_pci_inta), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO AS-i PWRD */
+ offsetof(struct ioctrl512x, io_control_pci_frame), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO LED0, LED1 */
+ offsetof(struct ioctrl512x, io_control_pci_idsel), 2,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* GPIO IRQ AS-i 1, IRQ AS-i 2, IRQ safety */
+ offsetof(struct ioctrl512x, io_control_pci_irdy), 3,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /* DIU clk */
+ offsetof(struct ioctrl512x, io_control_spdif_txclk), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(2) | IO_PIN_DS(2),
+ },
+ { /* FEC TX ER, CRS */
+ offsetof(struct ioctrl512x, io_control_spdif_tx), 2,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(1) | IO_PIN_DS(2),
+ },
+ { /* GPIO/GPT */ /* to *NOT* have the EXT IRQ0 float */
+ offsetof(struct ioctrl512x, io_control_irq0), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ { /*
+ * FEC col, tx en, tx clk, txd 0-3, mdc, rx er,
+ * rdx 3-0, mdio, rx clk
+ */
+ offsetof(struct ioctrl512x, io_control_psc0_0), 15,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(1) | IO_PIN_DS(2),
+ },
+ /* optional: make sure PSC3 remains the serial console */
+ { /* LPC CS6 */
+ offsetof(struct ioctrl512x, io_control_psc3_4), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(1) | IO_PIN_DS(2),
+ },
+ /* make sure PSC4 remains available for SPI,
+ *BUT* PSC4_1 is a GPIO kind of SS! */
+ { /* enforce drive strength on the SPI pin */
+ offsetof(struct ioctrl512x, io_control_psc4_0), 5,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+ {
+ offsetof(struct ioctrl512x, io_control_psc4_1), 1,
+ IO_PIN_OVER_FMUX,
+ IO_PIN_FMUX(3),
+ },
+ /* optional: make sure PSC5 remains available for SPI */
+ { /* enforce drive strength on the SPI pin */
+ offsetof(struct ioctrl512x, io_control_psc5_0), 5,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(1),
+ },
+ { /* LPC TSIZ1 */
+ offsetof(struct ioctrl512x, io_control_psc6_0), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(1) | IO_PIN_DS(2),
+ },
+ { /* DIU hsync */
+ offsetof(struct ioctrl512x, io_control_psc6_1), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(2) | IO_PIN_DS(1),
+ },
+ { /* DIU vsync */
+ offsetof(struct ioctrl512x, io_control_psc6_4), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(2) | IO_PIN_DS(1),
+ },
+ { /* PSC7, part of DIU RGB */
+ offsetof(struct ioctrl512x, io_control_psc7_0), 2,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(2) | IO_PIN_DS(1),
+ },
+ { /* PSC7, safety UART */
+ offsetof(struct ioctrl512x, io_control_psc7_2), 2,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(0) | IO_PIN_DS(1),
+ },
+ { /* DIU (part of) RGB[] */
+ offsetof(struct ioctrl512x, io_control_psc8_3), 16,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(2) | IO_PIN_DS(1),
+ },
+ { /* DIU data enable */
+ offsetof(struct ioctrl512x, io_control_psc11_4), 1,
+ IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
+ IO_PIN_FMUX(2) | IO_PIN_DS(1),
+ },
+ /* reduce LPB drive strength for improved EMI */
+ { /* LPC OE, LPC RW */
+ offsetof(struct ioctrl512x, io_control_lpc_oe), 2,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+ { /* LPC AX03 through LPC AD00 */
+ offsetof(struct ioctrl512x, io_control_lpc_ax03), 36,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+ { /* LPC CS5 */
+ offsetof(struct ioctrl512x, io_control_pata_ce2), 1,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+ { /* SDHC CLK */
+ offsetof(struct ioctrl512x, io_control_nfc_wp), 1,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+ { /* SDHC DATA */
+ offsetof(struct ioctrl512x, io_control_nfc_ale), 4,
+ IO_PIN_OVER_DRVSTR,
+ IO_PIN_DS(2),
+ },
+};
+
+int checkboard(void)
+{
+ puts("Board: ifm AC14xx\n");
+
+ /* initialize function mux & slew rate IO inter alia on IO Pins */
+ iopin_initialize_bits(ioregs_init, ARRAY_SIZE(ioregs_init));
+
+ return 0;
+}
+
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+}
+#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
projects / karo-tx-uboot.git / blobdiff