/*
* Basic board specific setup
*/
+static const struct pin_mux tx48_pads[] = {
+ { OFFSET(i2c0_sda), MODE(7) | RXACTIVE | PULLUDEN | PULLUP_EN, },
+ { OFFSET(i2c0_scl), MODE(7) | RXACTIVE | PULLUDEN | PULLUP_EN, },
+ { OFFSET(emu1), MODE(7), }, /* ETH PHY Reset */
+};
+
+static const struct pin_mux tx48_i2c_pads[] = {
+ { OFFSET(i2c0_sda), MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN, },
+ { OFFSET(i2c0_scl), MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN, },
+};
+
+static const struct gpio tx48_gpios[] = {
+ { AM33XX_GPIO_NR(3, 5), GPIOFLAG_INPUT, "I2C1_SDA", },
+ { AM33XX_GPIO_NR(3, 6), GPIOFLAG_INPUT, "I2C1_SCL", },
+ { AM33XX_GPIO_NR(3, 8), GPIOFLAG_OUTPUT_INIT_LOW, "ETH_PHY_RESET", },
+};
+
static const struct pin_mux stk5_pads[] = {
/* heartbeat LED */
{ OFFSET(gpmc_a10), MODE(7) | PULLUDEN, },
};
static const struct gpio stk5_gpios[] = {
- { TX48_LED_GPIO, GPIOF_OUTPUT_INIT_LOW, "HEARTBEAT LED", },
- { TX48_MMC_CD_GPIO, GPIOF_INPUT, "HEARTBEAT LED", },
+ { TX48_LED_GPIO, GPIOFLAG_OUTPUT_INIT_LOW, "HEARTBEAT LED", },
+ { TX48_MMC_CD_GPIO, GPIOFLAG_INPUT, "MMC0 CD", },
};
static const struct pin_mux stk5_lcd_pads[] = {
};
static const struct gpio stk5_lcd_gpios[] = {
- { AM33XX_GPIO_NR(1, 19), GPIOF_OUTPUT_INIT_LOW, "LCD RESET", },
- { AM33XX_GPIO_NR(1, 22), GPIOF_OUTPUT_INIT_LOW, "LCD POWER", },
- { AM33XX_GPIO_NR(3, 14), GPIOF_OUTPUT_INIT_HIGH, "LCD BACKLIGHT", },
+ { AM33XX_GPIO_NR(1, 19), GPIOFLAG_OUTPUT_INIT_LOW, "LCD RESET", },
+ { AM33XX_GPIO_NR(1, 22), GPIOFLAG_OUTPUT_INIT_LOW, "LCD POWER", },
+ { AM33XX_GPIO_NR(3, 14), GPIOFLAG_OUTPUT_INIT_HIGH, "LCD BACKLIGHT", },
};
static const struct pin_mux stk5v5_pads[] = {
};
static const struct gpio stk5v5_gpios[] = {
- { AM33XX_GPIO_NR(0, 22), GPIOF_OUTPUT_INIT_HIGH, "CAN XCVR", },
+ { AM33XX_GPIO_NR(0, 22), GPIOFLAG_OUTPUT_INIT_HIGH, "CAN XCVR", },
};
#ifdef CONFIG_LCD
.vl_col = 1366,
.vl_row = 768,
- .vl_bpix = LCD_COLOR24, /* Bits per pixel, 0: 1bpp, 1: 2bpp, 2: 4bpp, 3: 8bpp ... */
+ .vl_bpix = LCD_COLOR32, /* Bits per pixel, 0: 1bpp, 1: 2bpp, 2: 4bpp, 3: 8bpp ... */
.cmap = tx48_cmap,
};
}
karo_fdt_move_fdt();
- lcd_bl_polarity = karo_fdt_get_backlight_polarity(working_fdt);
if (video_mode == NULL) {
debug("Disabling LCD\n");
lcd_enabled = 0;
return;
}
+
+ lcd_bl_polarity = karo_fdt_get_backlight_polarity(working_fdt);
vm = video_mode;
if (karo_fdt_get_fb_mode(working_fdt, video_mode, &fb_mode) == 0) {
p = &fb_mode;
panel_info.vl_bpix = LCD_COLOR16;
break;
default:
- panel_info.vl_bpix = LCD_COLOR24;
+ panel_info.vl_bpix = LCD_COLOR32;
}
p->pixclock = KHZ2PICOS(refresh *
/* called with default environment! */
int board_init(void)
{
+ int i;
+
/* mach type passed to kernel */
#ifdef CONFIG_OF_LIBFDT
gd->bd->bi_arch_number = -1;
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
- if (ctrlc())
- printf("CTRL-C detected\n");
+ if (ctrlc() || (prm_rstst & PRM_RSTST_WDT1_RST)) {
+ if (prm_rstst & PRM_RSTST_WDT1_RST)
+ printf("WDOG RESET detected\n");
+ else
+ printf("<CTRL-C> detected; safeboot enabled\n");
+ }
+
+ gpio_request_array(tx48_gpios, ARRAY_SIZE(tx48_gpios));
+ tx48_set_pin_mux(tx48_pads, ARRAY_SIZE(tx48_pads));
+
+ for (i = 0; i < ARRAY_SIZE(tx48_gpios); i++) {
+ int gpio = tx48_gpios[i].gpio;
+ if (gpio_get_value(gpio) == 0)
+ gpio_direction_output(gpio, 1);
+ }
+
+ tx48_set_pin_mux(tx48_pads, ARRAY_SIZE(tx48_i2c_pads));
return 0;
}
prm_rstst = readl(PRM_RSTST);
show_reset_cause(prm_rstst);
-#ifdef CONFIG_OF_LIBFDT
- printf("Board: Ka-Ro TX48-7020 with FDT support\n");
-#else
printf("Board: Ka-Ro TX48-7020\n");
-#endif
+
timer_init();
return 0;
}
static void tx48_set_cpu_clock(void)
{
unsigned long cpu_clk = getenv_ulong("cpu_clk", 10, 0);
+ unsigned long act_cpu_clk;
- if (had_ctrlc() || (prm_rstst & PRM_RSTST_WDT1_RST))
+ if (cpu_clk == 0 || cpu_clk == mpu_clk_rate() / 1000000)
return;
- if (cpu_clk == 0 || cpu_clk == mpu_clk_rate() / 1000000)
+ if (had_ctrlc() || (prm_rstst & PRM_RSTST_WDT1_RST)) {
+ printf("%s detected; skipping cpu clock change\n",
+ (prm_rstst & PRM_RSTST_WDT1_RST) ?
+ "WDOG RESET" : "<CTRL-C>");
return;
+ }
mpu_pll_config_val(cpu_clk);
- printf("CPU clock set to %lu.%03lu MHz\n",
- mpu_clk_rate() / 1000000,
- mpu_clk_rate() / 1000 % 1000);
+ act_cpu_clk = mpu_clk_rate();
+ if (cpu_clk * 1000000 != act_cpu_clk) {
+ printf("Failed to set CPU clock to %lu MHz; using %lu.%03lu MHz instead\n",
+ cpu_clk, act_cpu_clk / 1000000,
+ act_cpu_clk / 1000 % 1000);
+ } else {
+ printf("CPU clock set to %lu.%03lu MHz\n",
+ act_cpu_clk / 1000000, act_cpu_clk / 1000 % 1000);
+ }
}
static void tx48_init_mac(void)
mac_addr[4] = mac_lo & 0xFF;
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
- if (!is_valid_ether_addr(mac_addr)) {
+ if (!is_valid_ethaddr(mac_addr)) {
printf("No valid MAC address programmed\n");
return;
}
int ret = 0;
const char *baseboard;
+ env_cleanup();
+
tx48_set_cpu_clock();
- karo_fdt_move_fdt();
+
+ if (had_ctrlc())
+ setenv_ulong("safeboot", 1);
+ else if (prm_rstst & PRM_RSTST_WDT1_RST)
+ setenv_ulong("wdreset", 1);
+ else
+ karo_fdt_move_fdt();
baseboard = getenv("baseboard");
if (!baseboard)
}
#ifdef CONFIG_DRIVER_TI_CPSW
-static void tx48_phy_init(char *name, int addr)
+static void tx48_phy_init(void)
{
debug("%s: Resetting ethernet PHY\n", __func__);
.hw_stats_reg_ofs = 0x900,
.mac_control = (1 << 5) /* MIIEN */,
.control = cpsw_control,
- .phy_init = tx48_phy_init,
.gigabit_en = 0,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_2,
{
__raw_writel(RMII_MODE_ENABLE, MAC_MII_SEL);
__raw_writel(0x5D, GMII_SEL);
+ tx48_phy_init();
return cpsw_register(&cpsw_data);
}
#endif /* CONFIG_DRIVER_TI_CPSW */
"ti,am3359-tscadc",
};
-void ft_board_setup(void *blob, bd_t *bd)
+int ft_board_setup(void *blob, bd_t *bd)
{
const char *baseboard = getenv("baseboard");
int stk5_v5 = baseboard != NULL && (strcmp(baseboard, "stk5-v5") == 0);
int ret;
ret = fdt_increase_size(blob, 4096);
- if (ret)
+ if (ret) {
printf("Failed to increase FDT size: %s\n", fdt_strerror(ret));
-
+ return ret;
+ }
fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
fdt_fixup_ethernet(blob);
karo_fdt_fixup_touchpanel(blob, tx48_touchpanels,
ARRAY_SIZE(tx48_touchpanels));
- karo_fdt_fixup_usb_otg(blob, "usb0", "phys");
+ karo_fdt_fixup_usb_otg(blob, "usb0", "phys", "vcc-supply");
karo_fdt_fixup_flexcan(blob, stk5_v5);
karo_fdt_update_fb_mode(blob, video_mode);
tx48_disable_watchdog();
+
+ if (get_cpu_rev() == 0) {
+ karo_fdt_del_prop(blob, "lltc,ltc3589-2", 0x34, "interrupts");
+ karo_fdt_del_prop(blob, "lltc,ltc3589-2", 0x34,
+ "interrupt-parent");
+ }
+
+ return 0;
}
#endif /* CONFIG_OF_BOARD_SETUP */
projects / karo-tx-uboot.git / blobdiff