#include <i2c.h>
#include <netdev.h>
#include <spi.h>
+#include <asm/gpio.h>
#include <asm/arch/cpu.h>
#include <asm/arch/dwmmc.h>
-#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/power.h>
#include <asm/arch/sromc.h>
#include <power/pmic.h>
#include <power/max77686_pmic.h>
+#include <power/tps65090_pmic.h>
#include <tmu.h>
DECLARE_GLOBAL_DATA_PTR;
static void board_enable_audio_codec(void)
{
/* Enable MAX98095 Codec */
+ gpio_request(EXYNOS5_GPIO_X17, "max98095_enable");
gpio_direction_output(EXYNOS5_GPIO_X17, 1);
gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE);
}
return 0;
}
+#if defined(CONFIG_POWER)
+#ifdef CONFIG_POWER_MAX77686
+static int pmic_reg_update(struct pmic *p, int reg, uint regval)
+{
+ u32 val;
+ int ret = 0;
+
+ ret = pmic_reg_read(p, reg, &val);
+ if (ret) {
+ debug("%s: PMIC %d register read failed\n", __func__, reg);
+ return -1;
+ }
+ val |= regval;
+ ret = pmic_reg_write(p, reg, val);
+ if (ret) {
+ debug("%s: PMIC %d register write failed\n", __func__, reg);
+ return -1;
+ }
+ return 0;
+}
+
+static int max77686_init(void)
+{
+ struct pmic *p;
+
+ if (pmic_init(I2C_PMIC))
+ return -1;
+
+ p = pmic_get("MAX77686_PMIC");
+ if (!p)
+ return -ENODEV;
+
+ if (pmic_probe(p))
+ return -1;
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN))
+ return -1;
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT,
+ MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V))
+ return -1;
+
+ /* VDD_MIF */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT,
+ MAX77686_BUCK1OUT_1V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK1OUT);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL,
+ MAX77686_BUCK1CTRL_EN))
+ return -1;
+
+ /* VDD_ARM */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1,
+ MAX77686_BUCK2DVS1_1_3V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK2DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1,
+ MAX77686_BUCK2CTRL_ON))
+ return -1;
+
+ /* VDD_INT */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1,
+ MAX77686_BUCK3DVS1_1_0125V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK3DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL,
+ MAX77686_BUCK3CTRL_ON))
+ return -1;
+
+ /* VDD_G3D */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1,
+ MAX77686_BUCK4DVS1_1_2V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK4DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1,
+ MAX77686_BUCK3CTRL_ON))
+ return -1;
+
+ /* VDD_LDO2 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1,
+ MAX77686_LD02CTRL1_1_5V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO3 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1,
+ MAX77686_LD03CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO5 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1,
+ MAX77686_LD05CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO10 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1,
+ MAX77686_LD10CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ return 0;
+}
+#endif /* CONFIG_POWER_MAX77686 */
+
+int exynos_power_init(void)
+{
+ int ret = 0;
+
+#ifdef CONFIG_POWER_MAX77686
+ ret = max77686_init();
+ if (ret)
+ return ret;
+#endif
+#ifdef CONFIG_POWER_TPS65090
+ /*
+ * The TPS65090 may not be in the device tree. If so, it is not
+ * an error.
+ */
+ ret = tps65090_init();
+ if (ret == 0 || ret == -ENODEV)
+ return 0;
+#endif
+
+ return ret;
+}
+#endif /* CONFIG_POWER */
+
#ifdef CONFIG_LCD
+static int board_dp_bridge_setup(void)
+{
+ const int max_tries = 10;
+ int num_tries, node;
+
+ /*
+ * TODO(sjg): Use device tree for GPIOs when exynos GPIO
+ * numbering patch is in mainline.
+ */
+ debug("%s\n", __func__);
+ node = fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_NXP_PTN3460);
+ if (node < 0) {
+ debug("%s: No node for DP bridge in device tree\n", __func__);
+ return -ENODEV;
+ }
+
+ /* Setup the GPIOs */
+
+ /* PD is ACTIVE_LOW, and initially de-asserted */
+ gpio_request(EXYNOS5_GPIO_Y25, "dp_bridge_pd");
+ gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE);
+ gpio_direction_output(EXYNOS5_GPIO_Y25, 1);
+
+ /* Reset is ACTIVE_LOW */
+ gpio_request(EXYNOS5_GPIO_X15, "dp_bridge_reset");
+ gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE);
+ gpio_direction_output(EXYNOS5_GPIO_X15, 0);
+
+ udelay(10);
+ gpio_set_value(EXYNOS5_GPIO_X15, 1);
+
+ gpio_request(EXYNOS5_GPIO_X07, "dp_bridge_hpd");
+ gpio_direction_input(EXYNOS5_GPIO_X07);
+
+ /*
+ * We need to wait for 90ms after bringing up the bridge since there
+ * is a phantom "high" on the HPD chip during its bootup. The phantom
+ * high comes within 7ms of de-asserting PD and persists for at least
+ * 15ms. The real high comes roughly 50ms after PD is de-asserted. The
+ * phantom high makes it hard for us to know when the NXP chip is up.
+ */
+ mdelay(90);
+
+ for (num_tries = 0; num_tries < max_tries; num_tries++) {
+ /* Check HPD. If it's high, we're all good. */
+ if (gpio_get_value(EXYNOS5_GPIO_X07))
+ return 0;
+
+ debug("%s: eDP bridge failed to come up; try %d of %d\n",
+ __func__, num_tries, max_tries);
+ }
+
+ /* Immediately go into bridge reset if the hp line is not high */
+ return -ENODEV;
+}
+
void exynos_cfg_lcd_gpio(void)
{
/* For Backlight */
+ gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
gpio_set_value(EXYNOS5_GPIO_B20, 1);
/* LCD power on */
+ gpio_request(EXYNOS5_GPIO_X15, "lcd_power");
gpio_cfg_pin(EXYNOS5_GPIO_X15, S5P_GPIO_OUTPUT);
gpio_set_value(EXYNOS5_GPIO_X15, 1);
{
set_dp_phy_ctrl(onoff);
}
+
+void exynos_backlight_on(unsigned int on)
+{
+ debug("%s(%u)\n", __func__, on);
+
+ if (!on)
+ return;
+
+#ifdef CONFIG_POWER_TPS65090
+ int ret;
+
+ ret = tps65090_fet_enable(1); /* Enable FET1, backlight */
+ if (ret)
+ return;
+
+ /* T5 in the LCD timing spec (defined as > 10ms) */
+ mdelay(10);
+
+ /* board_dp_backlight_pwm */
+ gpio_direction_output(EXYNOS5_GPIO_B20, 1);
+
+ /* T6 in the LCD timing spec (defined as > 10ms) */
+ mdelay(10);
+
+ /* board_dp_backlight_en */
+ gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
+ gpio_direction_output(EXYNOS5_GPIO_X30, 1);
+#endif
+}
+
+void exynos_lcd_power_on(void)
+{
+ int ret;
+
+ debug("%s\n", __func__);
+
+#ifdef CONFIG_POWER_TPS65090
+ /* board_dp_lcd_vdd */
+ tps65090_fet_enable(6); /* Enable FET6, lcd panel */
+#endif
+
+ ret = board_dp_bridge_setup();
+ if (ret && ret != -ENODEV)
+ printf("LCD bridge failed to enable: %d\n", ret);
+}
+
#endif
projects / karo-tx-uboot.git / blobdiff