-if TARGET_SUN4I
+if ARCH_SUNXI
-config SYS_CONFIG_NAME
- string
- default "sun4i"
+choice
+ prompt "Sunxi SoC Variant"
-endif
+config MACH_SUN4I
+ bool "sun4i (Allwinner A10)"
+ select CPU_V7
+ select SUPPORT_SPL
-if TARGET_SUN5I
+config MACH_SUN5I
+ bool "sun5i (Allwinner A13)"
+ select CPU_V7
+ select SUPPORT_SPL
-config SYS_CONFIG_NAME
- string
- default "sun5i"
+config MACH_SUN6I
+ bool "sun6i (Allwinner A31)"
+ select CPU_V7
+ select SUPPORT_SPL
-endif
+config MACH_SUN7I
+ bool "sun7i (Allwinner A20)"
+ select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-if TARGET_SUN7I
+config MACH_SUN8I
+ bool "sun8i (Allwinner A23)"
+ select CPU_V7
+ select SUPPORT_SPL
-config SYS_CONFIG_NAME
- string
- default "sun7i"
+endchoice
+
+if MACH_SUN6I || MACH_SUN8I
+
+config DRAM_CLK
+ int "sun6i dram clock speed"
+ default 312
+ ---help---
+ Set the dram clock speed, valid range 240 - 480, must be a multiple
+ of 24.
+
+config DRAM_ZQ
+ int "sun6i dram zq value"
+ default 123
+ ---help---
+ Set the dram zq value.
endif
-if TARGET_SUN4I || TARGET_SUN5I || TARGET_SUN7I
+config SYS_CONFIG_NAME
+ default "sun4i" if MACH_SUN4I
+ default "sun5i" if MACH_SUN5I
+ default "sun6i" if MACH_SUN6I
+ default "sun7i" if MACH_SUN7I
+ default "sun8i" if MACH_SUN8I
+
+choice
+ prompt "Board"
+
+config TARGET_A10_OLINUXINO_L
+ bool "A10_OLINUXINO_L"
+ depends on MACH_SUN4I
+
+config TARGET_A10S_OLINUXINO_M
+ bool "A10S_OLINUXINO_M"
+ depends on MACH_SUN5I
+
+config TARGET_A13_OLINUXINOM
+ bool "A13_OLINUXINOM"
+ depends on MACH_SUN5I
+
+config TARGET_A13_OLINUXINO
+ bool "A13_OLINUXINO"
+ depends on MACH_SUN5I
+
+config TARGET_A20_OLINUXINO_L2
+ bool "A20_OLINUXINO_L2"
+ depends on MACH_SUN7I
+
+config TARGET_A20_OLINUXINO_L
+ bool "A20_OLINUXINO_L"
+ depends on MACH_SUN7I
+
+config TARGET_A20_OLINUXINO_M
+ bool "A20_OLINUXINO_M"
+ depends on MACH_SUN7I
+
+config TARGET_AUXTEK_T004
+ bool "AUXTEK_T004"
+ depends on MACH_SUN5I
+
+config TARGET_BANANAPI
+ bool "BANANAPI"
+ depends on MACH_SUN7I
+
+config TARGET_BANANAPRO
+ bool "BANANAPRO"
+ depends on MACH_SUN7I
+
+config TARGET_COLOMBUS
+ bool "COLOMBUS"
+ depends on MACH_SUN6I
+
+config TARGET_CUBIEBOARD2
+ bool "CUBIEBOARD2"
+ depends on MACH_SUN7I
+
+config TARGET_CUBIEBOARD
+ bool "CUBIEBOARD"
+ depends on MACH_SUN4I
+
+config TARGET_CUBIETRUCK
+ bool "CUBIETRUCK"
+ depends on MACH_SUN7I
+
+config TARGET_HUMMINGBIRD_A31
+ bool "HUMMINGBIRD_A31"
+ depends on MACH_SUN6I
+
+config TARGET_IPPO_Q8H_V5
+ bool "IPPO_Q8H_V5"
+ depends on MACH_SUN8I
+
+config TARGET_PCDUINO3
+ bool "PCDUINO3"
+ depends on MACH_SUN7I
+
+config TARGET_MELE_A1000G
+ bool "MELE_A1000G"
+ depends on MACH_SUN4I
+
+config TARGET_MELE_A1000
+ bool "MELE_A1000"
+ depends on MACH_SUN4I
-config SYS_CPU
- string
- default "armv7"
+config TARGET_MELE_M3
+ bool "MELE_M3"
+ depends on MACH_SUN7I
+
+config TARGET_MELE_M9
+ bool "MELE_M9"
+ depends on MACH_SUN6I
+
+config TARGET_MINI_X_1GB
+ bool "MINI_X_1GB"
+ depends on MACH_SUN4I
+
+config TARGET_MINI_X
+ bool "MINI_X"
+ depends on MACH_SUN4I
+
+config TARGET_MSI_PRIMO73
+ bool "MSI Primo73 (7\" tablet)"
+ depends on MACH_SUN7I
+ ---help---
+ The MSI Primo73 is an A20 based tablet, with 1G RAM, 16G NAND,
+ 1024x600 TN LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
+ rear camera, 3000 mAh battery, gt911 touchscreen, mma8452 accelerometer
+ and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
+ (both volume buttons are also connected to the UBOOT_SEL pin). The
+ external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
+ OTG and 3.5mm headphone jack. More details are available at
+ http://linux-sunxi.org/MSI_Primo73
+
+config TARGET_MSI_PRIMO81
+ bool "MSI Primo81 (7.85\" tablet)"
+ depends on MACH_SUN6I
+ ---help---
+ The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
+ 1024x768 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
+ rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
+ and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
+ (both volume buttons are also connected to the UBOOT_SEL pin). The
+ external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
+ OTG and 3.5mm headphone jack. More details are available at
+ http://linux-sunxi.org/MSI_Primo81
+
+config TARGET_BA10_TV_BOX
+ bool "BA10_TV_BOX"
+ depends on MACH_SUN4I
+
+config TARGET_I12_TVBOX
+ bool "I12_TVBOX"
+ depends on MACH_SUN7I
+
+config TARGET_QT840A
+ bool "QT840A"
+ depends on MACH_SUN7I
+
+config TARGET_R7DONGLE
+ bool "R7DONGLE"
+ depends on MACH_SUN5I
+
+endchoice
config SYS_BOARD
- string
default "sunxi"
config SYS_SOC
- string
default "sunxi"
-config FTDFILE
- string "Default ftdfile env setting for this board"
+config SPL_FEL
+ bool "SPL/FEL mode support"
+ depends on SPL
+ default n
+
+config UART0_PORT_F
+ bool "UART0 on MicroSD breakout board"
+ depends on SPL_FEL
+ default n
+ ---help---
+ Repurpose the SD card slot for getting access to the UART0 serial
+ console. Primarily useful only for low level u-boot debugging on
+ tablets, where normal UART0 is difficult to access and requires
+ device disassembly and/or soldering. As the SD card can't be used
+ at the same time, the system can be only booted in the FEL mode.
+ Only enable this if you really know what you are doing.
+
+config FDTFILE
+ string "Default fdtfile env setting for this board"
+
+config OLD_SUNXI_KERNEL_COMPAT
+ boolean "Enable workarounds for booting old kernels"
+ default n
+ ---help---
+ Set this to enable various workarounds for old kernels, this results in
+ sub-optimal settings for newer kernels, only enable if needed.
+
+config MMC0_CD_PIN
+ string "Card detect pin for mmc0"
+ default ""
+ ---help---
+ Set the card detect pin for mmc0, leave empty to not use cd. This
+ takes a string in the format understood by sunxi_name_to_gpio, e.g.
+ PH1 for pin 1 of port H.
+
+config MMC1_CD_PIN
+ string "Card detect pin for mmc1"
+ default ""
+ ---help---
+ See MMC0_CD_PIN help text.
+
+config MMC2_CD_PIN
+ string "Card detect pin for mmc2"
+ default ""
+ ---help---
+ See MMC0_CD_PIN help text.
+
+config MMC3_CD_PIN
+ string "Card detect pin for mmc3"
+ default ""
+ ---help---
+ See MMC0_CD_PIN help text.
+
+config MMC_SUNXI_SLOT_EXTRA
+ int "mmc extra slot number"
+ default -1
+ ---help---
+ sunxi builds always enable mmc0, some boards also have a second sdcard
+ slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
+ support for this.
+
+config USB1_VBUS_PIN
+ string "Vbus enable pin for usb1 (ehci0)"
+ default "PH6" if MACH_SUN4I || MACH_SUN7I
+ default "PH27" if MACH_SUN6I
+ ---help---
+ Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes
+ a string in the format understood by sunxi_name_to_gpio, e.g.
+ PH1 for pin 1 of port H.
+
+config USB2_VBUS_PIN
+ string "Vbus enable pin for usb2 (ehci1)"
+ default "PH3" if MACH_SUN4I || MACH_SUN7I
+ default "PH24" if MACH_SUN6I
+ ---help---
+ See USB1_VBUS_PIN help text.
+
+config VIDEO
+ boolean "Enable graphical uboot console on HDMI, LCD or VGA"
+ default y
+ ---help---
+ Say Y here to add support for using a cfb console on the HDMI, LCD
+ or VGA output found on most sunxi devices. See doc/README.video for
+ info on how to select the video output and mode.
+
+config VIDEO_HDMI
+ boolean "HDMI output support"
+ depends on VIDEO && !MACH_SUN8I
+ default y
+ ---help---
+ Say Y here to add support for outputting video over HDMI.
+
+config VIDEO_VGA
+ boolean "VGA output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting video over VGA.
+
+config VIDEO_VGA_VIA_LCD
+ boolean "VGA via LCD controller support"
+ depends on VIDEO && MACH_SUN5I
+ default n
+ ---help---
+ Say Y here to add support for external DACs connected to the parallel
+ LCD interface driving a VGA connector, such as found on the
+ Olimex A13 boards.
+
+config VIDEO_LCD_MODE
+ string "LCD panel timing details"
+ depends on VIDEO
+ default ""
+ ---help---
+ LCD panel timing details string, leave empty if there is no LCD panel.
+ This is in drivers/video/videomodes.c: video_get_params() format, e.g.
+ x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
+
+config VIDEO_LCD_POWER
+ string "LCD panel power enable pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the power enable pin for the LCD panel. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config VIDEO_LCD_BL_EN
+ string "LCD panel backlight enable pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the backlight enable pin for the LCD panel. This takes a string in the
+ the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of
+ port H.
+
+config VIDEO_LCD_BL_PWM
+ string "LCD panel backlight pwm pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the backlight pwm pin for the LCD panel. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config USB_KEYBOARD
+ boolean "Enable USB keyboard support"
+ default y
+ ---help---
+ Say Y here to add support for using a USB keyboard (typically used
+ in combination with a graphical console).
endif
projects / karo-tx-uboot.git / blobdiff