endchoice
-if MACH_SUN6I || MACH_SUN8I
-
config DRAM_CLK
- int "sun6i dram clock speed"
- default 312
+ int "sunxi dram clock speed"
+ default 312 if MACH_SUN6I || MACH_SUN8I
+ default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
---help---
Set the dram clock speed, valid range 240 - 480, must be a multiple
of 24.
config DRAM_ZQ
- int "sun6i dram zq value"
- default 123
+ int "sunxi dram zq value"
+ default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
+ default 127 if MACH_SUN7I
---help---
Set the dram zq value.
+if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+config DRAM_EMR1
+ int "sunxi dram emr1 value"
+ default 0 if MACH_SUN4I
+ default 4 if MACH_SUN5I || MACH_SUN7I
+ ---help---
+ Set the dram controller emr1 value.
endif
config SYS_CONFIG_NAME
choice
prompt "Board"
-config TARGET_A10_OLINUXINO_L
- bool "A10_OLINUXINO_L"
- depends on MACH_SUN4I
-
config TARGET_A10S_OLINUXINO_M
bool "A10S_OLINUXINO_M"
depends on MACH_SUN5I
bool "BANANAPRO"
depends on MACH_SUN7I
-config TARGET_COLOMBUS
- bool "COLOMBUS"
- depends on MACH_SUN6I
-
config TARGET_CUBIEBOARD2
bool "CUBIEBOARD2"
depends on MACH_SUN7I
-config TARGET_CUBIEBOARD
- bool "CUBIEBOARD"
- depends on MACH_SUN4I
-
config TARGET_CUBIETRUCK
bool "CUBIETRUCK"
depends on MACH_SUN7I
-config TARGET_HUMMINGBIRD_A31
- bool "HUMMINGBIRD_A31"
- depends on MACH_SUN6I
-
-config TARGET_IPPO_Q8H_V5
- bool "IPPO_Q8H_V5"
- depends on MACH_SUN8I
-
config TARGET_PCDUINO3
bool "PCDUINO3"
depends on MACH_SUN7I
-config TARGET_MELE_A1000G
- bool "MELE_A1000G"
- depends on MACH_SUN4I
-
-config TARGET_MELE_A1000
- bool "MELE_A1000"
- depends on MACH_SUN4I
-
config TARGET_MELE_M3
bool "MELE_M3"
depends on MACH_SUN7I
-config TARGET_MELE_M9
- bool "MELE_M9"
- depends on MACH_SUN6I
-
-config TARGET_MINI_X_1GB
- bool "MINI_X_1GB"
- depends on MACH_SUN4I
-
-config TARGET_MINI_X
- bool "MINI_X"
- depends on MACH_SUN4I
+config TARGET_MK802_A10S
+ bool "MK802_A10S"
+ depends on MACH_SUN5I
config TARGET_MSI_PRIMO73
bool "MSI Primo73 (7\" tablet)"
OTG and 3.5mm headphone jack. More details are available at
http://linux-sunxi.org/MSI_Primo73
-config TARGET_MSI_PRIMO81
- bool "MSI Primo81 (7.85\" tablet)"
- depends on MACH_SUN6I
- ---help---
- The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
- 1024x768 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
- rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
- and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
- (both volume buttons are also connected to the UBOOT_SEL pin). The
- external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
- OTG and 3.5mm headphone jack. More details are available at
- http://linux-sunxi.org/MSI_Primo81
-
-config TARGET_BA10_TV_BOX
- bool "BA10_TV_BOX"
- depends on MACH_SUN4I
-
config TARGET_I12_TVBOX
bool "I12_TVBOX"
depends on MACH_SUN7I
-config TARGET_QT840A
- bool "QT840A"
- depends on MACH_SUN7I
-
config TARGET_R7DONGLE
bool "R7DONGLE"
depends on MACH_SUN5I
slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
support for this.
+config USB0_VBUS_PIN
+ string "Vbus enable pin for usb0 (otg)"
+ default ""
+ ---help---
+ Set the Vbus enable pin for usb0 (otg). This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config USB1_VBUS_PIN
string "Vbus enable pin for usb1 (ehci0)"
default "PH6" if MACH_SUN4I || MACH_SUN7I
---help---
Say Y here to add support for outputting video over HDMI.
+config VIDEO_VGA
+ boolean "VGA output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting video over VGA.
+
config VIDEO_VGA_VIA_LCD
boolean "VGA via LCD controller support"
- depends on VIDEO
+ depends on VIDEO && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I)
default n
---help---
Say Y here to add support for external DACs connected to the parallel
LCD interface driving a VGA connector, such as found on the
Olimex A13 boards.
+config VIDEO_VGA_EXTERNAL_DAC_EN
+ string "LCD panel power enable pin"
+ depends on VIDEO_VGA_VIA_LCD
+ default ""
+ ---help---
+ Set the enable pin for the external VGA DAC. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config VIDEO_LCD_MODE
string "LCD panel timing details"
depends on VIDEO
This is in drivers/video/videomodes.c: video_get_params() format, e.g.
x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
+config VIDEO_LCD_DCLK_PHASE
+ int "LCD panel display clock phase"
+ depends on VIDEO
+ default 1
+ ---help---
+ Select LCD panel display clock phase shift, range 0-3.
+
config VIDEO_LCD_POWER
string "LCD panel power enable pin"
depends on VIDEO
Set the backlight pwm pin for the LCD panel. This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config VIDEO_LCD_BL_PWM_ACTIVE_LOW
+ bool "LCD panel backlight pwm is inverted"
+ depends on VIDEO
+ default y
+ ---help---
+ Set this if the backlight pwm output is active low.
+
+
+# Note only one of these may be selected at a time! But hidden choices are
+# not supported by Kconfig
+config VIDEO_LCD_IF_PARALLEL
+ bool
+
+config VIDEO_LCD_IF_LVDS
+ bool
+
+
+choice
+ prompt "LCD panel support"
+ depends on VIDEO
+ ---help---
+ Select which type of LCD panel to support.
+
+config VIDEO_LCD_PANEL_PARALLEL
+ bool "Generic parallel interface LCD panel"
+ select VIDEO_LCD_IF_PARALLEL
+
+config VIDEO_LCD_PANEL_LVDS
+ bool "Generic lvds interface LCD panel"
+ select VIDEO_LCD_IF_LVDS
+
+config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828
+ bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip"
+ select VIDEO_LCD_SSD2828
+ select VIDEO_LCD_IF_PARALLEL
+ ---help---
+ 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+
+config VIDEO_LCD_PANEL_HITACHI_TX18D42VM
+ bool "Hitachi tx18d42vm LCD panel"
+ select VIDEO_LCD_HITACHI_TX18D42VM
+ select VIDEO_LCD_IF_LVDS
+ ---help---
+ 7.85" 1024x768 Hitachi tx18d42vm LCD panel support
+
+endchoice
+
+
+config USB_MUSB_SUNXI
+ bool "Enable sunxi OTG / DRC USB controller in host mode"
+ default n
+ ---help---
+ Say y here to enable support for the sunxi OTG / DRC USB controller
+ used on almost all sunxi boards. Note currently u-boot can only have
+ one usb host controller enabled at a time, so enabling this on boards
+ which also use the ehci host controller will result in build errors.
+
config USB_KEYBOARD
boolean "Enable USB keyboard support"
default y
projects / karo-tx-uboot.git / blobdiff