Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'

[karo-tx-uboot.git] / board / ti / ti814x / evm.c

diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
index c469645ff3d5a991595f42a990c88a1b8f0a8cd7..e406326a11eeca4de1208c9df1f0a39e149122c3 100644 (file)
--- a/board/ti/ti814x/evm.c
+++ b/board/ti/ti814x/evm.c
@@ -27,30 +27,10 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_SPL_BUILD
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#endif
-
 static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
 
 /* UART Defines */
 #ifdef CONFIG_SPL_BUILD
-static void uart_enable(void)
-{
-       /* UART softreset */
-       uart_soft_reset();
-}
-
-static void wdt_disable(void)
-{
-       writel(0xAAAA, &wdtimer->wdtwspr);
-       while (readl(&wdtimer->wdtwwps) != 0x0)
-               ;
-       writel(0x5555, &wdtimer->wdtwspr);
-       while (readl(&wdtimer->wdtwwps) != 0x0)
-               ;
-}
-
 static const struct cmd_control evm_ddr2_cctrl_data = {
        .cmd0csratio    = 0x80,
        .cmd0dldiff     = 0x04,
@@ -100,68 +80,39 @@ static const struct ddr_data evm_ddr2_data = {
        .datauserank0delay      = 1,
        .datadldiff0            = 0x4,
 };
-#endif
 
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+void set_uart_mux_conf(void)
 {
-#ifdef CONFIG_SPL_BUILD
-       /*
-        * Save the boot parameters passed from romcode.
-        * We cannot delay the saving further than this,
-        * to prevent overwrites.
-        */
-#ifdef CONFIG_SPL_BUILD
-       save_omap_boot_params();
-#endif
-
-       /* WDT1 is already running when the bootloader gets control
-        * Disable it to avoid "random" resets
-        */
-       wdt_disable();
-
-       /* Enable timer */
-       timer_init();
-
-       /* Setup the PLLs and the clocks for the peripherals */
-       pll_init();
-
-       /* Enable RTC32K clock */
-       rtc32k_enable();
-
        /* Set UART pins */
        enable_uart0_pin_mux();
+}
 
+void set_mux_conf_regs(void)
+{
        /* Set MMC pins */
        enable_mmc1_pin_mux();
 
        /* Set Ethernet pins */
        enable_enet_pin_mux();
+}
 
-       /* Enable UART */
-       uart_enable();
-
-       gd = &gdata;
-
-       preloader_console_init();
-
+void sdram_init(void)
+{
        config_dmm(&evm_lisa_map_regs);
 
        config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
                   &evm_ddr2_emif0_regs, 0);
        config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
                   &evm_ddr2_emif1_regs, 1);
-#endif
 }
+#endif
 
 /*
  * Basic board specific setup.  Pinmux has been handled already.
  */
 int board_init(void)
 {
-       gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+       gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
        return 0;
 }